Pelco Power Supply C655M A User Manual

I N S T A L L A T I O N / O P E R A T I O N  
MCS*E Series  
Master Power Supply  
C655M-A (1/07)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPLICATION EXAMPLES  
TableAcontainsexamplesofproductsandthenumberofunitsthatcanbepoweredbyeachpowersupply,andisbasedontheVAratingofeachproduct.  
Table A. Product Capacity  
Power Supply Model  
Product  
MCS4-2E  
MCS8-5E  
MCS16-10E  
MCS16-20E  
CDD Camera (12 VA maximum)  
DF5/DF5S with camera (3 VA)  
DF8A/PDF8 (12 VA maximum)  
Indoor Spectra (25 VA)  
Esprit (70 VA)  
4
4
8
8
8
4
1
16  
16  
16  
8
16  
16  
16  
16  
6
4
1
3
INSTALLATION  
The following items are supplied:  
1
2
2
MCS*E Series Power Supply  
Spare fuses  
Wire nuts  
To install an MCS Series power supply, perform the following steps:  
1. Decide where to install the unit.  
2. Open the lid on the unit by removing the 8-32 Phillips screw.  
3. Drill holes in the mounting surface. Use the unit as a template.  
4. Attach the unit securely with fourfasteners (not supplied) ofthe appropriate length. You can use fasteners up to 5/16-inch (0.80 cm) in diameter.  
5. Punch out the necessary knockouts. (There are six knockout holes on the top and two on the bottom.)  
6. Install 1/2-inch (1.27 cm) or 3/4-inch (1.91 cm) conduit fittings where necessary (conduit fittings not provided).  
WARNING: Pelco will not be liable for any damages resulting from incorrect wiring or improper loading of an MCS*E Series power supply.  
INPUT CONNECTIONS  
Table B. Main Fuse Value Table  
MCS4-2E  
MCS88-5E  
MCS16-10E MCS16-20E  
Fuse Location  
Main  
1A  
1A  
1.6A  
3A  
3A  
3A  
5A  
3A  
Individual Output  
1. Verify that the on/off switch inside the box is OFF.  
2. Remove the high voltage compartment panel inside the box.  
3. Attach the 120 input wires to the flying leads in the compartment with the supplied wire nuts (brown – AC line; blue – AC neutral).  
4. Attach the input ground wire to the stud inside the compartment with the supplied washer and nut.  
5. Replace the access panel.  
C655M-A (1/07)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
OUTPUT CONNECTIONS  
Perform the following steps to attach 24 VAC devices to the MCS*E Series power supply:  
1. Refer to Tables C and D in this manual or the wiring table on the unit’s lid to determine the output connection needed for your devices.  
2. Refer to Figure 1 for the proper connector strip connections.  
3. For each device, attach one output wire to the common terminal. Attach the second wire to the appropriate 24 VAC terminal.  
4. When you finish the wiring connections, double check the installation for safety purposes.  
5. Power up the unit with the on/off switch.  
6. Use a voltmeter to verify that used outputs are at appropriate voltage levels.  
7. Close the lid and secure it using the 8-32 Phillips screw.  
OUTPUT # 1  
(24 VAC)  
OUTPUT # 2  
(24 VAC)  
OUTPUT # 9  
(24 VAC)  
24V  
1
2
3
4
5
6
7
8
9
10 11 12  
13 14 15 16  
Main Fuse  
COM  
ON  
OFF  
Power  
OUTPUT 1 THRU 8  
OUTPUT 9 THRU 16  
Figure 1. MCS*E Series Unit Wiring Connector Diagram  
4
C655M-A (1/07)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table C. Recommended Wiring Distances  
The following are the recommended maximum distances (transformer to load) and are calculated with a 10-percent voltage drop. (Ten percent is  
generally the maximum allowable voltage drop for AC-powered devices.) Distances are calculated in feet; values in parentheses are meters.  
Wire Gauge  
Input  
Total VA  
Voltage  
Consumed  
20  
18  
16  
10  
20  
30  
50  
283 (86)  
141 (42)  
94 (28)  
56 (17)  
451 (137)  
225 (68)  
150 (45)  
90 (27)  
716 (218)  
358 (109)  
238 (72)  
143 (43)  
24 VAC  
You can use Table D as a guide to determine the necessary wire gauge (AWG) for various cable distances that provide 24 VAC power. Or use it in  
a reverse fashion to determine the maximum allowable cable distance for a particular wire gauge. Table D applies when using 2-conductor  
copper wire, with characteristics similar to West Penn 221-227 unshielded cable. Calculations are based on a 10-percent voltage drop (generally  
the maximum allowable drop for AC-powered devices).  
The minimum acceptable voltage is calculated as follows: 24.0 VAC  
–02.4 (10%)  
21.6 (Minimum Acceptable Voltage)  
The minimum acceptable voltage used to create Table D was 21.6 volts. Therefore, the 24-volt output has an acceptable range from 24 volts  
down to 21.6 volts.  
Table D. Required Wire Gauge  
Require Wire Gauge Table (AWG)  
WIRE  
DIST  
(feet)  
Equipment Loads  
!
10VA  
20VA  
30VA  
40VA  
50VA  
60VA  
70VA  
80VA  
90VA  
N/A  
100VA  
200VA  
1000  
900  
800  
700  
600  
500  
400  
300  
200  
100  
12-14  
12-14  
12-14  
12-16  
12-16  
12-16  
12-18  
12-18  
12-20  
12-22  
12  
12  
N/A  
12  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
12  
12  
12  
12  
12  
12  
12  
12  
12-14  
12-14  
12-16  
12-18  
12-20  
12  
12  
12  
12  
12  
12-14  
12-16  
12-18  
12  
12  
12  
12  
12-14  
12-18  
12-14  
12-16  
12  
12  
12  
12  
12-16  
12-16  
12-14  
12-14  
12-14  
XX-XX  
Recommended Wire Gauge (AWG) using 24 VAC  
N/A – Distance and load not recommended for any wire size between 12-22 (AWG)  
C655M-A (1/07)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
There are no user-serviceable parts except for the fuses. If the transformer in the unit does not work properly, the entire power supply needs to  
be returned to the factory for repair. Refer to the Warranty and Return Information section of this manual for instructions on returning the power  
supply for repair.  
Clean the outer surface of the power supply with a nonabrasive cleaning cloth and anti-static cleaner. Do not use kerosene or similar substances  
that may damage the surface.  
SPECIFICATIONS  
MECHANICAL  
Cable Entry  
Fuse Size  
Knockouts for either 1/2-inch (1.27 cm) or 3/4-inch (1.91 cm) conduit  
All fuses are 5 x 20 mm  
ELECTRICAL  
Input Voltage  
120 VAC, 60 Hz  
24 VAC  
Output Voltage  
Required Input Current  
See Models section  
Output Fuse Ratings  
MCS4-2E  
MCS8-5E  
MCS16-10E  
MCS16-20E  
1 A*  
3 A*  
3 A*  
3 A*  
Input Connectors  
Wire nut  
Output Connectors  
Input Wire Size  
Screw-type barrier strips  
12-16 gauge solid wire  
12-22 gauge solid or stranded wire  
See Table C  
Output Wire Size  
Recommended Wiring Distances  
GENERAL  
Construction  
Finish  
Steel  
Black polyester powder coat  
Indoor  
Environment  
Operating Temperature  
Dimensions  
32° to 120°F (0° to 50°C)  
4.37" D x 10.86" W x 16.13" H (11.10 x 27.58 x 40.97 cm)  
Unit Weight  
MCS4-2E  
MCS8-5E  
MCS16-10E  
MCS16-20E  
13.45 lb (6.10 kg)  
14.70 lb (6.67 kg)  
16.60 lb (7.53 kg)  
19.70 lb (8.94 kg)  
Ratings  
Meets NEMA Type 1 standards  
*Individual output cannot exceed this rating, and the total of all outputs cannot exceed the overall rating of the power supply (see the models  
section)  
(Design and product specifications subject to change without notice.)  
6
C655M-A (1/07)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission  
products.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Spectra® IV products.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product when  
returned.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra III, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair).  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product lia-  
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such  
Products. In no event will Pelco be liable for any special, incidental or consequential damages  
(including loss of use, loss of profit and claims of third parties) however caused, whether by  
the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C655M  
Date  
6/99  
1/07  
Comments  
Original version.  
C655M-A  
Updated Table A VA ratings for Spectra and Esprit. Added operating temperature. Reformatted document.  
Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura, and Spectra III are trademarks of Pelco.  
©Copyright 2007, Pelco. All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore  
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States  
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peerless Industries TV Mount MM746PU User Manual
Peg Perego Riding Toy SPST5981GR User Manual
Philips Coffeemaker HD7832 55 User Manual
Philips Flat Panel Television 19 20 23 26 47PFL5522D User Manual
Philips Satellite TV System SDV2927 User Manual
Philips Universal Remote 12 User Manual
Pioneer CD Player DEH 2000MP User Manual
Pontiac Automobile 2008 grand prix User Manual
Porter Cable Saw 347k User Manual
Poulan Chainsaw 530086667 User Manual