®
WLVEH Enclosure
for
Wireless Control/Video Systems
Installation/Operation Manual
C907M-A (7/96)
Pelco • 300 W. Pontiac Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-209) 292-1981
FAX (800) 289-9150 or (1-209) 292-3827 • DataFAX (800) 289-9108 or (1-209) 292-0435
International customers call (1-209) 292-1981 or FAX (1-209) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION/OPERATION MANUAL
WLVEH ENCLOSURE
FOR WIRELESS CONTROL/VIDEO SYSTEMS
1.0 WARNINGS
Prior to installation and use of this product, the follow-
ing WARNINGS should be observed.
1. Installation and servicing should only be done by
qualified service personnel and conform to FCC
regulations and all Local codes.
4. OnlyusereplacementpartsrecommendedbyPelco.
5. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
betweenlineandexposedpartstoverifytheexposed
parts have not been connected to line circuitry.
2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.
3. The product may bear the following marks:
This symbol indicates that there are important
operating and maintenance instructions in the
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TOREDUCETHERISKOFELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information in this manual
prior to installation and operation.
Pelco Manual C907M-A (7/96)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Reinstall the transmitter mounting plate (11) in-
side the enclosure. There are two sets of four
mounting holes on the enclosure mounting plate
(15). On units without an omnidirectional dipole
antenna, use the top holes to provide more clear-
ance for making connections to the transmitter.
2.0 SCOPE
This manual covers the installation of the following
wireless systems in the WLVEH outdoor enclosure:
WLV500 Series of control systems
WLV2000 Series of video systems
6. Connect the power leads inside the enclosure to
the transmitter. The red wire attaches to the posi-
tive (+) terminal and the black wire to the nega-
tive (-) terminal.
3.0 DESCRIPTION
The WLVEH Enclosure is a NEMA-rated housing that
protects the WLV500 Series of wireless control sys-
tems and WLV2000 Series of wireless video systems
in outdoor environments.
7. There are two Phillips screws (I) on the bottom of
the enclosure. Nothing is attached to them when a
transmitter is installed in the enclosure.
Input power to the enclosure is selectable from either
120 VAC, 24 VAC, or 230 VAC. The AC input is con-
verted to a regulated 15 VDC to power the wireless
system.
8. Close the lid.
9. To complete the installation, refer to the instruc-
tions for outdoor installation in your WLV500 or
WLV2000 manual.
The enclosure can be mounted to a flat surface or to a
pole when installed with Pelco's PA102 pole mount,
and PA9000 pole mount adapter.
4.2 RECEIVER
4.0 INSTALLATION
Refer to Figure 1 to install the wireless receiver. The
following instructions apply to both the WLV500 and
WLV2000 units.
You can install either a wireless transmtter unit or a
wireless receiver unit in the enclosure. Proceed to ei-
ther Section 4.1, “Transmitter” or Section 4.2, “Re-
ceiver.”
1. Open the lid of the enclosure.
2. Remove the four screws that secure the receiver
mounting plate (item 11) to the enclosure mount-
ing plate (15).
4.1 TRANSMITTER
Refer to Figure 1 to install the wireless transmitter. The
following instructions apply to both the WLV500 and
WLV2000 units.
3. Install the receiver to the receiver mounting plate
so that the electrical connections on the receiver
face the bottom of the enclosure. Use four small
Phillips screws and lockwashers that are supplied
with the receiver.
1. Open the lid of the enclosure.
2. Remove the four screws that secure the transmit-
ter mounting plate (item 11) to the enclosure
mounting plate (15).
4. Reinstall the receiver mounting plate (11) inside
the enclosure. There are two sets of four mounting
holes on the enclosure mounting plate (15). On
units without an omnidirectional dipole antenna,
use the top holes to provide more clearance for
making connections to the bottom of the receiver.
3. Install the transmitter to the transmitter mounting
plate so that the electrical connections on the trans-
mitter face the bottom of the enclosure. Use four
small Phillips screws and lockwashers that are sup-
plied with the transmitter.
5. Connect the power leads inside the enclosure to
the receiver. The red wire attaches to the positive
(+) terminal and the black wire to the negative (-)
terminal.
4. If you have an omnidirectional dipole antenna,
screw it onto the transmitter.
2
Pelco Manual C907M-A (7/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. There are two Phillips screws (I) on the bottom of
the enclosure. If you are installing a WLV500 re-
ceiver, they are not used. If your are installing a
WLV2000 receiver, they are test points for mea-
suring Received Signal Strength Indication (RSSI).
Wire the test points as follows:
5.0 SPECIFICATIONS
Power Input:
Construction:
24, 120, or 230 VAC
Fiberglass box with NEMA 4X rat-
ing
a. Solder one end of a wire to the solder lug on
receiver mounting plate. Solder the other end
of the wire to the solder lug on the Phillips
screw on the left (the screw to the left of I) on
the bottom of the enclosure.
IEC 144 Rating: IP66
Dimensions:
Cable Entry:
4.3" H x 11.5" L x 9.5" W
(10.92 x 29.21 x 24.13 cm)
One (1) gland for power cord
Two (2) glands for video and audio
coaxial cable
b. Solder one end of a wire to the solder lug on
the Phillips screw on the right (I) on the bot-
tom of the enclosure. Screw the other end of
the wire into the tip plug that is supplied.
Locking
Method:
Latches with holes for padlocks
c. Push the tip plug into the green connector on
the front of the receiver.
Weight (excluding wireless transmitter or receiver)
Enclosure:
Shipping:
8.6 lbs (3.90 kg)
10.6 lbs (4.81 kg)
7. Attach the receive antenna (18) to the antenna
mounting bracket (16).
8. Screw the connector on the end of the antenna cable
onto the mating connector on the top of the receiver.
9. Close the lid.
10. To complete the installation, refer to the instruc-
tions for outdoor installation in your WLV500 or
WLV2000 manual.
Pelco Manual C907M-A (7/96)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 EXPLODED ASSEMBLY DIAGRAM
Figure 1. WLVEH Outdoor Enclosure Exploded Assembly Diagram
4
Pelco Manual C907M-A (7/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
6.1 MECHANICAL PARTS LIST
Item
Quantity
Description
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
2
2
1
1
2
1
1
1
1
1
4
4
1
1
1
1
1
2
9-Pin Connector
Gland
Gland Nut
Gland
Gland Nut
Fuse Holder
Power Supply Assembly
3-Position Terminal Block
Transformer
Power Cord (not shown)
Transmitter/Receiver Mounting Plate
Fixed Tilt Bracket
Adjustment Bracket
Enclosure Box
CON03-06-1091
EH400010003
EH400010004
CX950010000
CX950010001
FUS342012L
PCB9000281ASSY
TRB3-140Y
TRF21162.01.OCM
WIRC1318006BL
WLV4100COMP
WLV4155COMP
WLV4156COMP
WLVEH4000COMP
WLVEH4151COMP
WLVEH5152COMP
—
Mounting Plate
Antenna Mounting Bracket
Wireless Transmitter or Receiver
Receive Antenna
1/4 Amp, Slow Blow, 3AG Fuse
—
FUS1/4SB
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
8
12
12
4
4
6
6
6
2
4
10
12
8
4
2
Screw, 1/4-20 x 1/2-inch
Split Lock Washer, 1/4-inch
Flat Washer
Bolt, 1/4-20 x 5/8-inch
1/4-20 Nut
Screw, 10-32 x 1/2-ich, Pan Head, Phillips
Internal Tooth Lock Washer, #10
Flat Washer, #10
Screw, 8-32 x 1/2-inch, Flat Head, Phillips
8-32 Nut
Screw, 6-32 x 3/8-inch, Pan Head, Phillips
Internal Tooth Lock Washer, #6
Flat Washer, #6
ZH1/4-20X.500CH
ZH1/4LWSSL
ZH260X562X65C
ZH1/420X.625CH
ZH1/4-20NUTCH
ZH10-32X.500SPP
ZH10LWSIS
ZH204X436X60C
ZH8-32X.500SFS
ZH8-32NUTSH
ZH6-32X.375SPP
ZH6LWSIS
ZH148X375X32C
ZH6-32NUTSH
ZH6-32X.500SPP
ZH4-40X.250SPP
ZH4LWSIS
6-32 Nut
Screw, 6-32 x 1/2-inch, Pan Head, Phillips
Screw, 4-40 x 1/4-inch, Pan Head, Phillips
Internal Tooth Lock Washer, #4
4
4
7.0 WIRING DIAGRAM
NOTE: Output voltage is 15 VDC, not 10.5.
Figure 2. WLVEH Outdoor Enclosure Wiring Diagram
Pelco Manual C907M-A (7/96)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8.0 WARRANTY AND RETURN
INFORMATION
If a warranty repair is required, contact Pelco at (800)
289-9100 or (209) 292-1981 for a Repair
Authorizationnumber(RA), andprovidethefollowing
information:
WARRANTY
Pelco will repair or replace, without charge, any
merchandise proved defective in material or
workmanship for a period of one (1) year after the date
of shipment. Exceptions to this warranty are as noted
below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order
number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product
which does not fall under the warranty conditions
stated above, please include a written explanation with
the product when returned.
•
Two (2) years on all standard motorized and fixed
focal length lenses.
•
Two (2) years on Legacy®, Intercept®, CM8500/
CM9500/CM9750 Matrix, and DF8 Fixed Dome
products.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
•
Two (2) years on WW5700 series window wiper
(excluding wiper blades).
Method of return shipment shall be the same as method
by which the repair item is received by Pelco.
•
•
Two (2) years on cameras.
RETURNS
Six (6) months on all pan and tilts, scanners or
preset lenses used in continuous motion
applications (e.g., preset scan, tour and auto scan
modes).
In order to expedite parts returned to the factory for
repair or credit, please call the factory at (800) 289-
9100or (209)292-1981toobtainanauthorization
number (CA number if returned for credit, and RA
number if returned for repair). Goods returned for
repair or credit should be clearly identified with the
assignedCA/RAnumberandfreightshouldbeprepaid.
All merchandise returned for credit may be subject to
a 20% restocking and refurbishing charge.
Pelco will warranty all replacement parts and repairs
for 90 days from the date of shipment. All goods for
warranty work shall be sent freight prepaid to our
Clovis, California facility. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident
are not covered under this warranty. Pelco is not liable
foranyincidentalorconsequentialexpensesorliability
incurred by the customer as a result of field repair,
installation, or any other reason.
Ship freight prepaid to: Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
The above warranty is in lieu of any other expressed or
implied warranty, condition, or guarantee by Pelco of
the equipment listed herein. Pelco makes no warranties
except for intended use and will not be liable for any
loss, damage, or costs arising, whether consequential
or incidental, from the use of said merchandise.
This warranty gives you specific legal rights. You may
alsohaveadditionalrights,whicharesubjecttovariation
from state to state.
6
Pelco Manual C907M-A (7/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
|