C249M-C (11/99)
PP300/PP301
Parapet Corner Mount
®
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
3500 Pelco Way,
Clovis, CA 93612-5699
USA
1. Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
2. Installation shall be done in accordance with all local and national electrical and mechanical
codes utilizing only approved materials.
International Customers:
Tel +1 (559) 292-1981
FAX +1 (559) 348-1120
3. Use only installation methods and materials capable of supporting four times the maximum
specified load.
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.
5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
DESCRIPTION
The PP300 and PP301 Parapet Corner Mounts are designed to eliminate the expense and haz-
ards of installing and servicing equipment that is to be mounted on the corners of rooftops and
parapets.
The PP300 mounts on top of rooftops and parapets. The PP301 mounts to the inside of para-
pets. Both mounts rotate 360 degrees in the horizontal plane, allowing equipment to be installed
or serviced from the rooftop easily and safely.
When using the PP300 or PP301 with a ED27/ED2720 or ED28/ED2820 Series Dome, the addi-
tion of the PPI200 Vertical Indexer is required. This will allow vertical rotation of the dome to ac-
quire the clearance needed to swing the boom of the mount over the roof, providing easy and
safe installation and serviceability.
When using the PP300 and PP301 to install equipment such as pan/tilts, a PA2010 or PA2000 is
required. In addition, a PM102A is required if mounting a PT175-24P Pan/Tilt.
INSTALLATION
The PP300/PP301 Parapet Corner Mount kit contains the following items:
WARNING: The
PP300/301 should be
securely mounted to the
Qty
1
Description
Strut pipe (ST1)
structure in accordance with ap-
plicable codes before installing
pan/tilt, etc. The twelve fasteners
to secure the PP300/PP301 to the
rooftop/parapet wall (such as lag
screws or concrete fasteners) are
not supplied. Minimum 3/8-inch
diameter fasteners are recom-
mended; 1/4-inch minimum for
corner wall bracket. Make certain
the mounting surface is able to
support the combined weight of
the mount and camera/enclosure.
1
2
2
2
4
4
4
Corner parapet wall bracket
5/16-18 nuts
5/16-18 x 2-inch carriage bolts
5/16 split lock washers
1/4-20 nuts
1/4-inch split lock washers
1/4-20 x 5/8-inch bolt
Right and left sideplates to turret base:
Qty
20
20
Description
1/4-inch split lock washers
1/4-20 nuts
Installing the Mount
To install the PP300/PP301 Parapet Corner Mount, perform the following steps.
1. Attach right and left sideplates to turret base using 1/4-inch split lock washers and 1/4-20
nuts provided.
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Manual
To order replacement parts for your unit, obtain a service manual in one of the following ways:
•
•
Contact Pelco’s Literature Department and request service manual C249SM.
Related Products
PA2000
PA2010
PM102A
PPI200
Mount adapter plate for medium-duty pan/tilts.
Mount adapter plate for heavy-duty pan/tilts.
Mount adapter plate for PT175-24P Pan/Tilt.
Vertical indexer adapter. Must be used with PP300/PP301 mount to adapt
ED27/ED2720 and ED28/ED2820 Series Domes.
PPI300
Indexing mount arm for parapet applications requiring 360 degrees of dome
rotation. For use with ED27/ED2720 and ED28/ED2820 Series Domes.
SPECIFICATIONS
Lock Positions:
15 degree increments
Positioning
Adjustment:
90 degrees
Suggested
Mounting Method: Secure to parapet or rooftop with twelve suitable fasteners (not supplied).
(3/8-inch diameter suggested minimum for PP300/PP301 and 1/4-inch for
strut plate)
Maximum Load:
Dimensions:
Construction:
Finish:
175 lb (78.75 kg) approximate
See Figures 4 and 5
Aluminum
Polyester powder coat
29 lb 11 oz. (13.40 kg)
Unit Weight
(Design and product specifications subject to change without notice.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 5. PP301 Dimension Diagram
Figure 4. PP300 Dimension Diagram
WARRANTY AND RETURN INFORMATION
WARRANTY
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
Pelco will repair or replace, without charge, any merchandise proved defective in material
or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera
models, which have a five-year warranty.
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
Method of return shipment shall be the same or equal to the method by which the item
was received by Pelco.
RETURNS
• Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
In order to expedite parts returned to the factory for repair or credit, please call the factory
at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.months on DX
Series digital video recorders, NVR300 Series network video recorders, Endura™ Series
distributed network-based video products, and TW3000 Series twisted pair transmission
products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods
to:
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Service Department
Pelco
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or
accident are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting
from the specific use or application made of the Products. Pelco’s liability for any claim,
whether based on breach of contract, negligence, infringement of any rights of any party
or product liability, relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties)
however caused, whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The above warranty provides the Dealer with specific legal rights. The Dealer may also
have additional rights, which are subject to variation from state to state.
REVISION HISTORY
Manual # Date
Comments
C249M
6/90
7/91
7/95
Original version.
C249M
C249M-B
Rev. A. Sections 4.0 and 4.1 revised. Sections 5.0 thru 5.2 and Figures 6 and 7 added.
Rev. B. Sections 3.0 and 3.2 revised to include ED27/ED2720 and PPI300. Section 5.1, step 9, revised to include ED27/
ED2720. References to ED25/ED2520/ED2620 and UMED25 removed.
C249M-C
11/99
Rev. C. Moved exploded assembly diagrams and parts lists to new maintenance/service manual (C249SM). Updated manual
to new format.
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|