Pelco Home Security System C1306M D 7 09 User Manual

I N S T A L L A T I O N

ExSite EHXM Series

Explosionproof

Fixed System

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

6. To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the supply circuit before opening. Keep assembly

tightly closed when in operation.

7. The maximum ambient temperature range is -76° to 140°F (-60° to 60°C).

8. Only use attachments/accessories specified by the manufacturer.

9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

10. Installation should be done only by qualified personnel and conform to all local codes.

11. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not

be installed where exposed to rain and moisture.

12. Use only installation methods and materials capable of supporting four times the maximum specified load.

13. Use stainless steel hardware to fasten the mount to outdoor surfaces.

14. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of

the building.

15. A readily accessible disconnect device shall be incorporated in the building installation wiring.

16. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform

any servicing other that contained in the operating instructions unless you are qualified to do so.

17. Only use replacement parts recommended by Pelco.

18. A certified flameproof, "d," sealing device such as a stopping box with setting compound shall be provided, either in the flameproof

enclosure or immediately at the entrance thereto.

19. For ambient temperatures below 14°F ( -10°C) use field wiring suitable for both minimum and maximum ambient temperature.

The product and/or manual may bear the following marks:

WARNING: This symbol indicates that dangerous voltage constituting a risk of electric shock

is present within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are important operating and maintenance instructions in the

literature accompanying this unit.

WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.

WARNING: To reduce the risk of ignition of hazardous atmospheres, disconnect the

equipment from the supply circuit before opening. Keep assembly tightly closed when

operating.

WARNING: To reduce the risk of ignition of hazardous atmospheres, conduit runs must have

a sealing fitting connected within 2 inches of the enclosure.

TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE

MAY BE PRESENT.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Getting Started

Thank you for purchasing Pelco’s ExSite^®EHXM Series explosionproof system. This manual includes instructions for installing all the components

of the system. Once the system installation is complete, refer to the operation/programming manual for instructions on how to operate and

program your system.

METHODS OF INSTALLATION

The system can be installed in a standard or inverted position. When installed for inverted operation, the camera orientation and controller

functions are reconfigured for normal operation through the system’s software. Hardware adjustment is not required for inverted operation.

Refer to Figure 1 for installation methods.

Figure 1. Methods of Installation

WARNINGS:

•

Total weight of the system is 34.7 lb (15.71 kg). Use caution when lifting and assembling the enclosure component on the power

module. It is recommended that non-slip gloves be worn during installation.

•

Do not turn the body of the enclosure more than 200° in either direction or damage to the power module cable may occur.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Power Module

Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum

specified load of the system (140 lb/63.5 kg).

NOTE: If required, install the optional TXB translator, fiber module, or UTP board before installing the power module. Refer to the installation

instructions supplied with the TXB translator, fiber module, or UTP board for installation instructions.

To install the power module, refer to Figure 2 and do the following:

1. Make sure the threads of the power module and the threads of the supplied M10 x 16 mm stainless steel bolts are free of dirt and debris.

2. Apply a generous amount of thread locking compound (supplied) to the threads of the power module and the threads of the stainless steel

bolts.

3. Face the conduit fitting of the power module towards the mating conduit fitting of the installation.

4. Use the supplied 8 mm Allen wrench to secure the power module to the mounting surface with four M10 x 16 mm stainless steel bolts and

lock washers. Tighten the bolts to 25 to 27 ft-lb (34 to 37 Nm). The thread locking compound supplied must cure for one hour. Allow for this

cure period prior to completing the installation.

NOTE: Figure 2 shows the power module

being installed on a PXM100 pedestal mount

(not supplied).

Figure 2. Attach Power Module to Mounting Surface

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECT WIRING

DANGER: Do not connect the power module to a supply circuit unless all ExSite system components (enclosure, camera module, and

power module) are installed.

Refer to the following information to connect the wires and cables as required.

WARNING: When installing this unit, provide access to the communication wires (TX+ and TX-) to allow connection to the system for

future software upgrades. Connectors must be installed so that the integrity of the hazardous location is maintained.

These communication wires are required even if the system uses Coaxitron^®control.

Maximum wire distance for RS-422 data wires is 4,000 ft (1,219 m).

NOTES:

•

Relay 3 is allocated specifically for an external washer (not supplied by Pelco).

All relays are specified for 32 VDC, 0.5 A.

Wiring/cable for UTP and fiber optic are not provided on the wire harness. The installer must provide UTP and fiber optic connections.

Power Connections 24 VAC

Configuration of Wire Harness

Wire Color

Red

Function

AC Hi

Wire Color

White/Orange

White/Blue

Red

Function

TX+

TX-

Black

AC Low

RX+

Green

RX-

Power Connections 100-240 VAC

Violet/White

White/Red

Relay 3 NC (washer only)

Relay 3 COM (washer only)

Relay 3 NO (washer only)

Relay 2 NC

Relay 2 COM

Relay 2 NO

Relay 1 NC

Relay 1 COM

Relay 1 NO

Alarm COM

Alarm 7

Wire Color

Black

Function

AC Hi

AC Low

Green/Black

Gray/White

Yellow

White

Green/Yellow

Earth Ground

Violet

Wiring Distances

Brown

The following are the recommended maximum distances for 24 VAC and

100-240 VAC applications and are calculated with a 10 percent voltage drop.

(Ten percent is generally the maximum allowable voltage drop for AC-powered

devices.)

Gray

White/Yellow/Black

White/Black/Green

White/Red/Black

White/Brown/Black

Orange

Wire Gauge

Power

Alarm 6

(1.0 mm²)

(1.5 mm²)

(2.5 mm²)

(3.5 mm²)

Alarm 5

27 ft

(8 m)

43 ft

(13 m)

120 ft

(36 m)

69 ft

(21 m)

190 ft

(58 m)

110 ft

(33 m)

310 ft

(94 m)

24 VAC

White/Orange/Black

White/Blue/Black

White/Brown

White/Black

Alarm 4

Alarm 3

100-240

VAC

75 ft

(23 m)

Alarm 2

Alarm 1

NOTE: Power consumption is 120 VA per unit. Use a power source with a

minimum of 150 VA.

Video Coaxial Cable Requirements

Cable Type*

RG59/U

Maximum Distance

750 ft (229 m)

RG6/U

1,000 ft (305 m)

1,500 ft (457 m)

RG11/U

*Cable requirements:

75-ohm impedance

All-copper center conductor

All-copper braided shield with 95% braid coverage

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

DIP SWITCH SETTINGS

Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top

of the power module.

NOTE: No DIP switch settings are required for Coaxitron control.

Figure 3 shows the default settings for the DIP switches. Refer to the following to configure the ExSite system settings.

SW1-1 is set to the ON position.

All other switches are set to the OFF position.

7 8

SW3

SW1

SW2

Figure 3. Default DIP Switch Settings

PROTOCOL SETTINGS

The ExSite system automatically detects the type of protocol. No switch settings are required to set Coaxitron or RS-422 P and D protocols.

RECEIVER ADDRESS SETTINGS (SW1)

The default address is 2 for P protocol. Refer to Table A for address settings that use P protocol. Maximum number of receivers is 32.

The default address is 1 for D protocol. Refer to Table B for address settings that use D protocol. Maximum number of receivers is 254.

TERMINATION SETTING (SW2)

When connecting more than one ExSite system to a single controller, terminate the unit farthest from the controller. Termination is required only

for the last unit in the series. The unit is shipped from the factory in the unterminated OFF position. To terminate the unit, set the SW2 switch to

the ON position.

BAUD SETTINGS (SW3)

Pelco’s D-type controllers are set for 2400 baud. The default setting for the unit is 2400 baud. If you are using a Pelco D-type controller, do not

reset the SW3 switches.

P-type controllers can operate at 2400, 4800, and 9600 baud. Set the SW3 switches (6, 7, and 8), located on the top of the power module, to the

same baud as the P-type controller.

Switch Settings for SW3

Switch Number

2400 Baud

SW3-6

Off

SW3-7

Off

SW3-8

Off

4800 Baud

Off

9600 Baud

Off

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. P Protocol Receiver Address

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

Table B. D Protocol Receiver Address

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

(Continued on next page)

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. D Protocol Receiver Address (Continued)

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

OFF

(Continued on next page)

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. D Protocol Receiver Address (Continued)

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

OFF

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

OFF

(Continued on next page)

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. D Protocol Receiver Address (Continued)

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

239

240

241

242

243

244

245

246

OFF

247

248

249

250

251

252

253

254

OFF

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Camera Module

To install the camera module, do the following:

1. Refer to Figure 4. Loosen the set screw at the back of the camera enclosure with the provided 1.5 mm Allen wrench.

SET SCREW

Figure 4. Loosen Set Screw

WARNING: To avoid thread damage carefully remove the back of the camera enclosure. Never use force to remove the back of the camera

enclosure.

2. Use the supplied spanner wrench to loosen the back of the camera enclosure (refer to Figure 5). Once the back is loose, use your hands to

continue to loosen it until it can be removed.

CAMERA

ENCLOSURE

BACK

SPANNER

WRENCH

Figure 5. Remove Back Cap of Camera Enclosure

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING: Do not force the camera module into the camera enclosure.

3. Slide the camera module into the camera enclosure. Refer to Figure 6 to position the camera module properly in the camera enclosure.

Carefully mate the camera’s power connector to the mating connector located inside the camera enclosure.

Models with a wiper: The tab located inside the camera enclosure must be pointing down before installing the camera module (refer to

Figure 6). To position the tab, place the wiper, located at the front of the camera enclosure, in the center of the viewing window (refer to

Figure 7).

TAB

CENTER

NOTCHES

CAMERA

MODULE

CAMERA

ENCLOSURE

Figure 6. Install Camera Module

CENTER WIPER

Figure 7. Center Wiper

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper:

a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same

orientation as shown in Figure 8.

b. Install the wiper arm. Place the ridge of the arm in the notch of the camera enclosure tab and the slot of the arm over the green

bushing.

5. Secure the camera module (and wiper) with the supplied 8-32 Phillips flat head screw (refer to Figure 8).

SET TAB IN

CENTER POSITION

8-32 PHILLIPS FLAT

HEAD SCREW

ARM

CAMERA

MODULE

HANDLE

STUD

BUSHING

Figure 8. Install Wiper Arm

WARNINGS:

•

To avoid thread damage carefully install the back cap to the camera enclosure.

Never force the back cap onto the end of the camera enclosure.

When installation is completed there should be no gap between the back cap and the camera enclosure.

6. Reinstall the back cap on the enclosure by doing the following:

a. Use your hands to turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until it

comes in contact with the O-ring. If it does not turn easily the threads are not aligned and thread damage will occur.

b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the enclosure

when the back cap is tightened and properly installed.

c. Once the back cap is installed, secure the back cap with the set screw using the supplied 1.5 mm Allen wrench.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Enclosure and Set Pan Position

1. Check for proper seating of the power module seal. Make sure the seal is fully seated in the groove on the top of the power module.

POWER MODULE SEAL

POWER MODULE

Figure 9. Factory-Installed Power Module Seal

WARNING: Use caution when attaching the enclosure unit to the power module. If the grooves on the top of the power module are

damaged, the integrity of the unit could be compromised.

2. Refer to Figure 10 and attach the enclosure unit to the power module. Align the pins of the enclosure unit with the holes of the power

module. Carefully mate the enclosure connector to the power module connector.

LOCKING

RING

HOLE

Figure 10. Attach the Enclosure Unit to the Power Module

WARNINGS:

•

Total weight of the enclosure component is 34.7 lb (15.71 kg). Use caution when lifting and assembling the pan and tilt component on

the power module.

•

The weight of the enclosure unit must be safely supported during installation.

It is recommended that non-slip gloves be worn during installation.

Avoid thread damage. Never use force when assembling and tightening the threaded components of the system.

3. Turn the body of the enclosure to the left or right to set the pan position of the unit.

WARNING: Do not turn the body of the enclosure more than 200° in either direction or damage to the internal power module cable may occur.

4. With your hands carefully thread the enclosure’s locking ring on the threads of the power module until the threads are completely engaged.

5. Use the supplied spanner wrench to tighten the locking ring and fix the position of the enclosure. After the locking ring has been tightened,

tap the end of the handle of the wrench with a hammer or the palm of your hand to ensure a secure fit. Make sure that the pan position is

maintained when tightening the locking ring. Tighten the set screw of the locking ring with the supplied 2 mm Allen wrench to secure the

locking ring.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Set the Tilt Angle of the Camera Module

1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wrench on the tilt shaft (refer to Figure 11).

TILT LOCK

NUT

SET SCREW

TILT SHAFT

Figure 11. Set the Tilt Position

2. Hold the tilt shaft in position with the 21 mm wrench, and then turn the 41 mm wrench to loosen the tilt locking nut.

3. Adjust the tilt position of the camera module by moving the camera module up or down.

4. Continue to hold the tilt shaft with the 21 mm wrench and then tighten the tilt locking nut to set the tilt position of the camera module.

Make sure the tilt position is maintained when tightening the locking ring. Tighten the set screw of the locking nut with the supplied 2 mm

Allen wrench to secure the locking nut.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Install the Sun Shroud

1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 12.

2. Align the mounting holes of the sun shroud with the holes on top of the camera enclosure.

3. Use the supplied nylon washers and screws to secure the sun shroud to the camera enclosure.

NYLON

WASHER

6-32 PHILLIPS PAN

HEAD SCREW

SUN SHROUD

Figure 12. Install the Sun Shroud

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

CAMERA MODULE REPLACEMENT

DANGER: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment from the power supply before opening.

Keep assembly tightly closed when operating.

To replace the camera module, do the following:

1. Remove the back cap of the camera enclosure. Refer to Figure 13 and do the following:

a. Loosen the set screw with a 1.5 mm Allen wrench.

b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure. Once the back is loose, use your hands to continue

to loosen it until it can be removed.

CAMERA

ENCLOSURE

BACK

SET SCREW

SPANNER

WRENCH

Figure 13. Remove Back Cap of Camera Enclosure

2. Remove the 8-32 Phillips flat head screw that secures the camera module inside the camera enclosure (refer to Figure 14).

SET TAB IN

CENTER POSITION

8-32 PHILLIPS FLAT

HEAD SCREW

ARM

CAMERA

MODULE

HANDLE

STUD

BUSHING

Figure 14. Remove or Install Camera Module

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Models with a wiper: Remove the wiper arm and the green bushing from the unit (refer to Figure 14).

4. Slide the camera module out of the enclosure.

WARNING: Never force the camera module into the enclosure.

5. Install the new camera module by doing the following:

Slide the camera module into the camera enclosure. Refer to Figure 15 to position the camera module properly in the camera enclosure.

Carefully mate the camera’s power connector to the mating connector located inside the camera enclosure.

Models with a wiper: The tab located inside the enclosure must be pointing down before installing the camera module (refer to

Figure 15). To position the tab, place the wiper, located at the front of the camera enclosure, in the center of the viewing window (refer to

Figure 16).

TAB

CENTER

NOTCHES

CAMERA

MODULE

CAMERA

ENCLOSURE

Figure 15. Install Camera Module

CENTER WIPER

Figure 16. Center Wiper

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Models with a wiper: Refer to Figure 14 and do the following to reinstall the arm of the wiper:

a. Reinstall the green bushing on the stud located behind the handle of the camera module.

b. Reinstall the wiper arm. Place the ridge of the arm in the notch of the camera enclosure tab and the slot of the arm over the green

bushing.

7. Secure the camera module and the wiper arm with the 8-32 Phillips flat head screw (refer to Figure 14).

WARNINGS:

•

To avoid thread damage, carefully install the back cap to the enclosure.

Never force the back cap onto the end of the enclosure.

When installation is completed, there should be no gap between the back cap and the camera enclosure.

8. Reinstall the back cap on the camera enclosure by doing the following:

a. Use your hands to turn the back cap clockwise until you can no longer turn it with your hands. The back cap should turn easily until it

comes in contact with the O-ring. If it does not turn easily, the threads are not aligned and thread damage will occur.

b. Continue tightening the back cap with the supplied spanner wrench. There should be no gap between the back cap and the camera

enclosure when the back cap is tightened and properly installed.

c. After the back cap is installed, secure the back cap with the set screw using a 1.5 mm Allen wrench.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

ELECTRICAL

Input Voltage

24 VAC or 100-240 VAC, 50/60 Hz

Input Voltage Range

Power Consumption

Heater and Defroster

Electrical Connections

10%

Maximum 60 W (120 VA) per system

Microprocessor controlled

6-foot wire harness with connections for power, video, data control, alarm inputs, and auxiliary outputs

MECHANICAL

Cable Entry

One 0.75-inch (1.91 cm) NPT threaded opening

GENERAL

Construction

316L stainless steel

Finish

Electropolish

Viewing Window

Operating Temperature

Unit Weight

0.50-inch (12.7 mm) thick, soda-lime tempered glass

-76° to 140°F (-60° to 60°C)

34.7 lb (15.71 kg)

Effective Projected Area (EPA)

97.3 square inches

CERTIFICATIONS

Class I, Groups A, B, C, and D

Class II, Groups E, F, G, T5

Class I, Zone 1, AEx d IIC, Ex d IIC, T5

BR-Ex d IIC, T5, IP66

04/UL-BRAE-0027

IECEx UL 04.0010X, Ex d IIC, T5

DEMKO 04 ATEX 0413858

0539

II 2 G Ex d IIC, T5

II 2 D Ex tD A21 IP66 T105°C

(Tamb -60°C to +60°C)

5.13

11.5 (29.21)

(13.03)

4.91

(12.47)

10.5

(26.8)

0.75 NPT

(1.91)

13.1 (33.27)

4 PLCS. TYP.

10MM - 1.5MM X 14MM

ON A 4.75-INCH DIA. B.C.

EQUALLY SPACED

3.354

(8.52)

NOTE: Values in parentheses are centimeters; all others are inches.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA/OPTICS

Camera

Day/Night (23X) Color

NTSC, PAL

2:1 Interlace

1/4-inch progressive scan CCD

LowLight^™(22X) Color

NTSC, PAL

2:1 Interlace

1/4-inch EXview HAD^™CCD

Signal Format

Scanning System

Image Sensor

Effective Pixels

NTSC

PAL

768 (H) x 494 (V)

752 (H) x 582 (V)

768 (H) x 494 (V)

752 (H) x 582 (V)

Horizontal Resolution

NTSC

PAL

540 TV lines

>470 TV lines

>460 TV lines

Lens

Zoom

f/1.6 (focal length, 3.6~82.8 mm optical)

23X optical, 10X digital

f/1.6 (focal length, 4~88 mm optical)

22X optical, 12X digital

Zoom Speed

2.9/4.2/5.8 seconds

2.4/3.9/6.3 seconds

Horizontal Angle of

View

54° at 3.6 mm wide zoom

2.5° at 82.8 mm telephoto zoom

47° at 4.0 mm wide zoom

2.2° at 88 mm telephoto zoom

Focus

Automatic with manual override

Maximum Sensitivity

at 35 IRE

NTSC

0.025 lux at 1/2 sec shutter (color)

0.1 lux at 1/60 sec shutter (B-W)

0.004 lux at 1/2 sec shutter (B-W)

0.02 lux at 1/2 sec shutter

PAL

0.025 lux at 1/1.5 sec shutter (color)

0.1 lux at 1/50 sec shutter (B-W)

0.004 lux at 1/1.5 sec shutter (B-W)

0.02 lux at 1/1.5 sec shutter

Sync System

Internal/AC line lock, phase adjustable using

remote control, V-Sync*

Internal/AC line lock, phase adjustable using

remote control, V-Sync*

White Balance

Automatic with manual override*

Shutter Speed

NTSC

PAL

Automatic (electronic iris)/Manual

1/2~1/30,000*

1/1.5~1/30,000*

Automatic (electronic iris)/Manual

1/2~1/30,000*

1/1.5~1/30,000*

Iris Control

Automatic Iris Control with manual override*

Gain Control

Video Output

Video Signal to Noise

Automatic/OFF*

1 Vp-p, 75 ohms

>50 dB

Automatic/OFF*

1 Vp-p, 75 ohms

>50 dB

*Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770,

CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000, or KBD9000 controllers.

C1306M-D (7/09)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in

material or workmanship for a period of one year after the date of shipment.

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Exceptions to this warranty are as noted below:

• Five years:

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s liability

for any claim, whether based on breach of contract, negligence, infringement of

any rights of any party or product liability, relating to the Products shall not exceed

the price paid by the Dealer to Pelco for such Products. In no event will Pelco be

liable for any special, incidental, or consequential damages (including loss of use,

loss of profit, and claims of third parties) however caused, whether by the

negligence of Pelco or otherwise.

–

Fiber optic products

TW3000 Series unshielded twisted pair (UTP) transmission products

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:

–

Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,

C10CH Series, IP3701H Series, and IX Series)

EH1500 Series enclosures

Spectra^®IV products (including Spectra IV IP)

Camclosure^®Series (IS, ICS, IP) integrated camera systems

–

The above warranty provides the Dealer with specific legal rights. The Dealer may

also have additional rights, which are subject to variation from state to state.

DX Series digital video recorders, DVR5100 Series digital video recorders,

Digital Sentry^®Series hardware products, DVX Series digital video

recorders, and NVR300 Series network video recorders

Endura^®Series distributed network-based video products

Genex^®Series products (multiplexers, server, and keyboard)

PMCL200/300/400 Series LCD monitors

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the

following information:

–

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

• Two years:

If there is a dispute regarding the warranty of a product that does not fall under

the warranty conditions stated above, please include a written explanation with

the product when returned.

–

Standard varifocal, fixed focal, and motorized zoom lenses

DF5/DF8 Series fixed dome products

Legacy^®Series integrated positioning systems

Spectra III^™, Spectra Mini, Spectra Mini IP, Esprit^®, ExSite^®, and PS20

scanners, including when used in continuous motion applications.

Method of return shipment shall be the same or equal to the method by which the

item was received by Pelco.

–

Esprit Ti and TI2500 Series thermal imaging products

Esprit and WW5700 Series window wiper (excluding wiper blades).

CM6700/CM6800/CM9700 Series matrix

RETURNS

To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100

or (559) 292-1981 to obtain an authorization number (CA number if returned for

credit, and RA number if returned for repair) and designated return location.

Digital Light Processing (DLP^®) displays (except lamp and color wheel). The

lamp and color wheel will be covered for a period of 90 days. The air filter is

not covered under warranty.

Intelli-M^®eIDC controllers

All merchandise returned for credit may be subject to a 20 percent restocking and

refurbishing charge.

–

• One year:

Video cassette recorders (VCRs), except video heads. Video heads will be

covered for a period of six months.

• Six months:

All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes).

–

Goods returned for repair or credit should be clearly identified with the assigned

CA or RA number and freight should be prepaid.

–

12-23-08

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

REVISION HISTORY

Manual #

C1306M

Date

8/05

Comments

Original version.

C1306M-A

C1306M-B

C1306M-C

C1306M-D

7/06

Updated for the new factory-installed power module seal (ECO 06-1400). Revised power module installation instructions. Removed Figure 9.

Removed color reference to power module seal (ECO 06-14300). Added power module warning. Added Figure 9.

Changed camera specs per CN22046.

10/06

11/08

7/09

Updated Important Safety Instructions section and added product certifications; UL certification requirement. Reference CN22827.

Pelco, the Pelco logo, Endura, ExSite, Spectra, Genex, Esprit, Camclosure, Coaxitron, and Legacy are registered trademarks of Pelco, Inc.

Spectra III is a trademark of Pelco, Inc.

LowLight is a trademark of Pelco, Inc.

EXview HAD is a trademark of Sony Corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

www.pelco.com

Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150

International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

Pelican Water Dispenser WF4 User Manual
Philips Car Satellite Radio System SDV9201 17 User Manual
Philips Indoor Furnishings 44992 30 16 User Manual
Philips Telephone SE4502B 17 User Manual
Philips TV Antenna SDW1410GN User Manual
Philips TV VCR Combo 14 20PT1354 User Manual
Pioneer Blu ray Player BDP 43FD User Manual
Poulan Snow Blower 192044 User Manual
Powerware Power Supply 8 10 kVA User Manual
ProForm Home Gym PFEX39912 User Manual