I N S T A L L A T I O N
FT106011/FR106011
Fiber Transmitter
and Receiver
Video with Bidirectional Audio, Data,
and Contact Closure
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
List of Illustrations
1
10 RS-232 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11 RS-422 Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
14 Manchester Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
15 Bi-Phase Data Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
16 Balanced Audio Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
17 Unbalanced Audio Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
C2649M (9/07)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Tables
Audio Select Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Data Select Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contact Closure Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Data Connector Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Audio Connector Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting with Front-Panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the points where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases shall be placed on the apparatus.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
16. Installation should be done only by qualified personnel and conform to all local codes.
17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.
18. Use only installation methods and materials capable of supporting four times the maximum
specified load.
19. A CCC-approved power cord must be used to power this equipment when used in China.
20. CAUTION: These servicing instructions are for use by qualified service personnel only. To
reduce the risk of electric shock do not perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
6
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this
equipment can void your authority to operate this equipment under Federal Communications
Commission’s rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Product Overview
DESCRIPTION
The FT106011/FR106011 fiber transmitter and receiver provide simultaneous transmission of one
unidirectional video channel, two bidirectional audio channels, one bidirectional data channel, and
one bidirectional contact closure over one optical fiber (refer to Figure 1).
VIDEO
AUDIO
VIDEO
AUDIO
FT106011
TRANSMITTER
FR106011
RECEIVER
DATA
CONTACT
CLOSURE
DATA
CONTACT
CLOSURE
ONE
FIBER
Figure 1. FT106011/FR106011 Video, Audio, Data, and Contact Closure Transmission
Features of the FT106011/FR106011 fiber optic transmission system include the following:
•
•
10-bit digitally encoded video for high-quality video transmission over a single fiber
Two bidirectional 24-bit digitally encoded audio channels with user-selectable 600-ohm
balanced or 47K-ohm unbalanced input impedance
•
Bidirectional data channel with user-selectable RS-232, RS-422, RS-485 (2-wire/4-wire),
Manchester, Bi-Phase, and Coaxitron® communication
•
•
•
•
Bidirectional contact closure that allows a choice of normally open or normally closed outputs
Multimode fiber support for distances up to 6 km (3.7 mi)
Single-mode fiber support for distances up to 38 km (23.6 mi)
Laser diode for transmission of optical signals
NOTE: The FT106011 transmitter/FR106011 receiver is a Class 1 laser product that complies
with FDA radiation performance standard 21CFR Subchapter J and with IEC 60825-1 Edition 1.2,
2001-08.
•
•
•
Patent-pending transmission technology allowing Coaxitron control at full-distance capabilities
Compatible with NTSC, PAL, and SECAM video standards
Designed to meet NEMA TS 2 and Caltrans traffic signal control equipment standards for
ambient operating temperature, mechanical shock and vibration, humidity with condensation,
high-line/low-line voltage conditions, and transient voltage protection
NOTE: Conformal coating is required for operation in environments with relative humidity
above 95 percent (condensing).
•
•
•
•
No performance adjustments required
12 VDC or 24 VAC power supply
Stand-alone and rack-mountable modular design
LED indicators for monitoring of signal status, laser status, data activity, contact closure
activation, and operating power
8
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS
The FT106011/FR106011 fiber transmitter and receiver consist of the following series of models:
Multimode Models:*
FT106011MSTR
FR106011MSTR
Fiber optic video transmitter with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; multimode,
ST connector
Fiber optic video receiver with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; multimode,
ST connector
Single-Mode Models:*
FT106011SSTR
FR106011SSTR
FT106011SFCR
FR106011SFCR
Fiber optic video transmitter with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; single-mode,
ST connector
Fiber optic video receiver with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; single-mode,
ST connector
Fiber optic video transmitter with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; single-mode,
FC connector
Fiber optic video receiver with two bidirectional audio channels, one
bidirectional data channel, and one bidirectional contact closure; single-mode,
FC connector
*For conformal coated models, replace the first letter F in the model number with the letter C.
The conformal coated version of FT106011MSTR, for example, is CT106011MSTR.
OPTIONAL ACCESSORIES
The following optional accessories are available:
WM5001-3U
Wall mount base kit for single-width module
WM5001-3UEXP Wall mount expansion kit for single-width module
RK5000-3U
19-inch rack mount chassis for 14 slots (no power), 3 RUs
19-inch rack mount chassis for 12 slots with power, 3 RUs
External rack power supply, 1 RU, dual 120 W power outputs
Blank filler panel, single width
RK5000PS-3U
EPS5000-120
RK5001B-3U
RK5002B-3U
RK5001-1UEXP
Blank filler panel, double width
Adapter kit that allows a 3 RU single-width fiber module to be used in
RK5000PS-5U rack mount chassis
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
9
FRONT PANEL
The front panel of the FT106011 transmitter and FR106011 receiver provides LED indicators that allow
you to monitor contact closure activation, audio signal status, data activity, video signal status, optical
FT106011
TRANSMITTER
FR106011
RECEIVER
Figure 2. Front Panel of FT106011 Transmitter and FR106011 Receiver
CONTACT CLOSURE LED
AUDIO PRESENT LED
DATA ACTIVITY LED
VIDEO PRESENT LED
OPTIC FAULT LED (optical signal status/laser status indicator)
POWER LED (Pelco badge)
10
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL
All connections to the FT106011 transmitter and FR106011 receiver are made to the rear panel of the
Figure 3. Rear Panel of FT106011 Transmitter and FR106011 Receiver
RACK POWER/ALARM CONNECTOR, 4-pin connector for power/alarm connection of rack-
mounted module
STAND-ALONE POWER CONNECTOR, 2-pin connector for power connection of stand-alone
module; removable mating connector with screw terminals (not shown)
FIBER OPTIC CONNECTOR, ST or FC (dependent on FT106011/FR106011 model)
CONTACT CLOSURE CONNECTOR, 6-pin connector; removable mating connector with tension
clamps (not shown)
DATA CONNECTOR, 8-pin connector; removable mating connector with tension clamps (not
shown)
AUDIO CONNECTOR, 12-pin connector; removable mating connector with tension clamps (not
shown)
BNC CONNECTOR, 75-ohm analog video input (FT106011)/output (FR106011)
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Installation
PACKAGE CONTENTS
The following items are supplied:
1
1
FT106011 transmitter or FR106011 receiver
Regulated switching power supply with four plug adapters (North American, Australian, U.K.,
and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output
1
1
1 small flat-tip screwdriver
Wall clip with two 4-40 x 0.25-inch Phillips pan head screws with lock washers (for attachment
of single module to wall)
1
FT106011/FR106011 Fiber Transmitter and Receiver Installation manual (this manual)
SETTING THE AUDIO SIGNAL AND IMPEDANCE MODE
An Audio Select switch, which is a 10-position rotary switch, is provided on the bottom of the
you to set the desired audio mode of operation.
With the FT106011 transmitter/FR106011 receiver powered off, set the Audio Select switch to the
desired mode of operation using the supplied screwdriver. Table B lists Audio Select switch settings
and associated audio modes of operation as indicated on the bottom of the units.
NOTE: If you wish to change the audio mode after the FT106011 transmitter/FR106011 receiver has
been powered on, power off the transmitter/receiver, change the audio mode, and then power on the
transmitter/receiver again.
12
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO SELECT SWITCH
AUDIO
DATA
SELECT
SELECT
0. UNBAL 47K
1. BAL 600
0. RS-232
1. RS-422
2-9 NOT USED
2. RS-485 2W
3. RS-485 4W
4. Man/Bi-Phase
5. Coaxitron
6-9 NOT USED
Figure 4. Audio Select Switch
Table A. Audio Select Switch Settings
Switch Setting
Audio Mode
0 (default setting)
UNBAL 47K Ω: Unbalanced audio signals, 47K-ohm input
impedance
BAL 600 Ω: Balanced audio signals, 600-ohm input
impedance
1
NOTE: Switch settings 2-9 are not used. If switch setting 2-9 is selected, the
Audio Present LED lights red.
C2649M (9/07)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE DATA COMMUNICATION MODE
A Data Select switch, which is a 10-position rotary switch, is provided on the bottom of the FT106011
the data communication mode required for the transfer of data.
With the FT106011 transmitter/FR106011 receiver powered off, set the Data Select switch to the
switch settings and associated data communication modes as indicated on the bottom of the units.
Note the following:
•
The FT106011 transmitter and the FR106011 receiver allow data translation between RS-232
and RS-422 signal levels. Consequently, the Data Select switch can be set to 0 (RS-232) on the
transmitter and to 1 (RS-422) on the receiver. Conversely, the Data Select switch can be set to
1 (RS-422) on the transmitter and to 0 (RS-232) on the receiver.
•
If you wish to change the data communication mode setting after the FT106011 transmitter/
FR106011 receiver has been powered on, power off the transmitter/receiver, change the data
communication mode setting, and then power on the transmitter/receiver again.
14
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA SELECT SWITCH
AUDIO
DATA
SELECT
SELECT
0. UNBAL 47K
1. BAL 600
0. RS-232
1. RS-422
2-9 NOT USED
2. RS-485 2W
3. RS-485 4W
4. Man/Bi-Phase
5. Coaxitron
6-9 NOT USED
Figure 5. Data Select Switch
Table B. Data Select Switch Settings
Switch Setting
Data Communication Mode
RS-232
0 (default setting)
1
2
3
4
5
RS-422
RS-485 2-Wire
RS-485 4-Wire
Manchester/Bi-Phase
Coaxitron
NOTE: Switch settings 6-9 are not used. If switch
setting 6-9 is selected, the Data Activity LED lights red.
C2649M (9/07)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING THE TRANSMITTER/RECEIVER
The FT106011 transmitter/FR106011 receiver can be mounted into a rack or can be used as a stand-
alone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to
a wall.
MOUNTING THE TRANSMITTER/RECEIVER INTO A RACK
The FT106011 transmitter/FR106011 receiver can be installed into an RK5000 Series rack mount
chassis, which can be mounted into an industry-standard 19-inch (48.26 cm) equipment rack. The
RK5000 Series rack mount chassis includes the following models:
•
RK5000PS-3U and RK5000-3U: Designed to accommodate fiber optic modules as follows:
–
–
The RK5000PS-3U rack mount chassis provides 12 module slots and a power supply.
The RK5000-3U rack mount chassis provides 14 module slots (a power supply is not
included). Power to the modules can be supplied using the optional external power
supply (EPS5000-120).
For additional information, refer to the RK5000PS-3U/RK5000-3U Fiber Rack Mount Chassis
Installation manual.
•
RK5000PS-5U: Designed to accommodate Endura™ modules but can also accommodate fiber
optic modules with the use of the RK5001-1UEXP adapter kit. The RK5001-1UEXP adapter kit
is required for installation of the FT106011 transmitter/FR106011 receiver into the
RK5000PS-5U chassis.
For information about the RK5000PS-5U chassis, refer to the RK5000PS-5U Rack Mount Chassis
Installation manual.
MOUNTING THE TRANSMITTER/RECEIVER TO A WALL
The FT106011 transmitter/FR106011 receiver can be mounted to a wall in the following ways:
•
Using the supplied wall clip for attachment of a single module to a wall. For installation
instructions, refer to the Mounting the Transmitter/Receiver Using the Wall Clip section.
•
Using the optional WM5001 wall mount kits, which are designed for mounting of single-width
fiber optic modules. The WM5001-3U base kit allows mounting of a single module to the wall.
The WM5001-3UEXP expansion kit allows mounting of an additional module. It is
recommended that a maximum of three expansion kits be used with the base kit, allowing a
maximum of four single-width modules to be mounted to the wall.
NOTE: The WM5001 wall mount kits can be used with the WM5002 wall mount kits, which are
designed for mounting of double-width fiber optic modules. If mounting a mix of single-width
and double-width modules is desired, it is recommended that a maximum of two single-width
modules and one double-width module be mounted in combination with one another.
For mounting instructions using the wall mount kits, refer to the WM5000 Series Wall Mount
Kit Installation manual.
16
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Transmitter/Receiver Using the Wall Clip
NOTE: Before mounting the FT106011 transmitter/FR106011 receiver to a wall, ensure that there is
adequate space at both ends for viewing the front-panel LEDs and for making the various rear-panel
cable connections.
To attach the FT106011 transmitter/FR106011 receiver to a wall using the supplied wall clip, refer to
Figure 6 and do the following:
1. Using the two vertical or horizontal wall-mounting holes, attach the wall clip to a wall using
two screws (not provided).
2. Slide the module into the clip until the two holes on the bottom of the module align with the
two holes on the lower flange of the clip.
3. Attach the module to the clip using the two Phillips pan head screws provided for the clip.
UPPER
FLANGE
VERTICAL
MOUNTING HOLE (2)
HORIZONTAL
MOUNTING HOLE (2)
LOWER
FLANGE
SCREW, PHILLIPS
PAN HEAD WITH
LOCK WASHER (2)
WALL CLIP
Figure 6. Mounting the FT106011 Transmitter/FR106011 Receiver Using the Wall Clip
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
17
CONNECTING THE TRANSMITTER/RECEIVER
Connections to the FT106011 transmitter and the FR106011 receiver are made on the rear panel of the
•
Power connection
NOTES:
–
–
A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when
used as a stand-alone module. A 12 VDC power supply is provided. If a 24 VAC power
supply is used, the power supply must be a Listed Direct Plug-In Power Unit marked as
Class 2 and rated as 24 VAC, 200 mA (minimum output).
In extreme temperature conditions, it is recommended that an industrial-rated outdoor
power supply be used.
•
•
•
•
•
•
Fiber connection
Contact closure connection
Data connection
Audio connection
Video input connection (transmitter only)
Video output connection (receiver only)
18
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER/ALARM CONNECTION
FOR RACK-MOUNTED MODULE
POWER CONNECTION
FOR STANDALONE MODULE
FIBER OPTIC CABLE
CONTACT CLOSURE, DATA, AND
AUDIO COMMUNICATIONS
CABLES (REFER TO TABLES C, D,
AND E FOR CONNECTOR PIN
ASSIGNMENTS AND TO
FIGURES 8-17 FOR WIRING
DIAGRAMS)
COAXIAL CABLE
TO INSERT OR REMOVE A WIRE,
DO THE FOLLOWING:
PIN 2
PIN 1
1. USING THE SUPPLIED
SCREWDRIVER, PRESS DOWN
ON THE APPROPRIATE CLAMP
UNTIL THE SCREWDRIVER IS
FIRMLY SEATED IN THE SLOT.
2. INSERT THE WIRE INTO OR
REMOVE THE WIRE FROM THE
ASSOCIATED PIN.
PIN 11
PIN 12
3. REMOVE THE SCREWDRIVER.
Figure 7. FT106011 Transmitter/FR106011 Receiver Connections
Table C. Contact Closure Pin Assignments
Pin Number
Contact Closure (CC)
In, Common
1
2
3 or 4
5
In
Out, Common
Out, Normally Open
Out, Normally Closed
6
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Table D. Data Connector Pin Assignments
Pin
RS-485
2-Wire
RS-485
4-Wire
Number RS-232
RS-422
Manchester
Bi-Phase
1
2
TX+ (Out+) T+/R+ (Out+/In+) TX+ (Out+)
TX+ (Out+) (W) TX+ (Out+)
TX- (Out-) (B) TX- (Out-)
RX+ (In+) (W) RX+ (In+)
TX-(Out-)
RX+ (In+)
RX- (In-)
—
T-/R-(Out-/In-)
TX- (Out-)
RX+ (In+)
RX- (In-)
—
3
4
5
6
—
—
—
—
—
—*
—
RX- (In-) (B)
—
RX- (In-)
—
RX (In)
TX (Out)
—
—
—
—
7 or 8 Ground
—*
—*
Shield
Shield
*Ground may be required based on conditions of installation. Refer to the current version of EIA/TIA-422
and EIA/TIA-485 standards for additional information.
NOTES:
•
TX (Out), TX+ (Out+), TX- (Out-), T+ (Out+), and T- (Out-) denote data output from the transmitter/
receiver.
•
•
•
RX (In), RX+ (In+), RX- (In-), R+ (In+), and R- (In-) denote data input to the transmitter/receiver.
W denotes white wire, and B denotes black wire.
Data ports are not terminated. For RS-422, RS-485 2-Wire, RS-485 4-Wire, Manchester, and
Bi-Phase data signals, termination may be required based on conditions of installation. If
termination is required, terminate the data signal at the endpoint of the data bus using a 120-ohm
resistor.
Table E. Audio Connector Pin Assignments
Pin Number
Balanced
In, Left+
Unbalanced
1
2
—
In, Right+
In, Left-
In, Right-
—
—
3
—
4
—
5
In, Left
In, Right
Shield
Out, Left
Out, Right
—
6
—
7 or 8
9
—
Out, Left+
Out, Right+
Out, Left-
Out, Right-
10
11
12
—
20
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
FT106011 TRANSMITTER –
CONTACT CLOSURE
CONNECTOR
CONTACT
CLOSURE
OUTPUT
IN
IN, COMMON
CONNECTIONS BETWEEN CONTACT CLOSURE OUTPUT AND FT106011 TRANSMITTER
FR106011 RECEIVER –
CONTACT CLOSURE
CONNECTOR
CONTACT
CLOSURE
INPUT
OUT, COMMON
OUT, NORMALLY OPEN
CONNECTIONS BETWEEN CONTACT CLOSURE INPUT AND FR106011 RECEIVER
Figure 8. Normally Open Contact Closure Wiring
FT106011 TRANSMITTER –
CONTACT CLOSURE
CONNECTOR
CONTACT
IN
IN, COMMON
CLOSURE
OUTPUT
CONNECTIONS BETWEEN CONTACT CLOSURE OUTPUT AND FT106011 TRANSMITTER
FR106011 RECEIVER –
CONTACT CLOSURE
CONNECTOR
CONTACT
CLOSURE
INPUT
OUT, COMMON
OUT,
NORMALLY CLOSED
CONNECTIONS BETWEEN CONTACT CLOSURE INPUT AND FR106011 RECEIVER
Figure 9. Normally Closed Contact Closure Wiring
C2649M (9/07)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
RX
RS-232
DATA SELECTION
0
TX
2
4
6
8
1
3
5
7
GND
TX
5
RX
GND
RS-232 DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
RS-232
RX
TX
DATA SELECTION
0
2
4
6
8
1
3
5
7
GND
TX
5
RX
GND
RS-232 DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 10. RS-232 Data Communication Wiring
22
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
RX+
RS-422
DATA SELECTION
0
TX-
RX-
TX+
RX+
RX-
2
4
6
8
1
3
5
7
TX+
5
TX-
RS-422 DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
RS-422
RX+
RX-
TX+
TX-
DATA SELECTION
0
TX-
RX-
TX+
RX+
2
4
6
8
1
3
5
7
5
RS-422 DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 11. RS-422 Data Communication Wiring
C2649M (9/07)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
R+/T+
RS-485 2-WIRE
DATA SELECTION
0
T-/R-
T+/R+
R-/T-
5
RS-485 2-WIRE DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
RS-485 2-WIRE
R+/T+
R-/T-
DATA SELECTION
0
T-/R-
T+/R+
5
RS-485 2-WIRE DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 12. RS-485 2-Wire (Half Duplex) Data Communication Wiring
24
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
RS-485 4-WIRE
RX+
RX-
TX+
TX-
DATA SELECTION
0
TX-
TX+
RX+
2
1
3
5
7
RX-
4
5
6
8
RS-485 4-WIRE DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
RS-485 4-WIRE
RX+
RX-
TX+
TX-
DATA SELECTION
0
TX-
TX+
RX+
2
1
3
5
7
RX-
4
5
6
8
RS-485 4-WIRE DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 13. RS-485 4-Wire (Full Duplex) Data Communication Wiring
C2649M (9/07)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
MANCHESTER
W*
B*
DATA SELECTION
0
2
4
6
8
1
3
5
7
RX-
RX+
5
SHIELD
MANCHESTER DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
MANCHESTER
W*
B*
DATA SELECTION
0
TX-
TX+
2
4
6
8
1
3
5
7
5
SHIELD
MANCHESTER DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
*W DENOTES WHITE WIRE, AND B DENOTES BLACK WIRE.
Figure 14. Manchester Data Communication Wiring
26
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
DATA CONNECTOR
DEVICE A
BI-PHASE
TX+
TX-
DATA SELECTION
0
2
4
6
8
1
3
5
7
RX-
RX+
5
SHIELD
BI-PHASE DATA CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
DATA CONNECTOR
DEVICE B
BI-PHASE
RX+
RX-
DATA SELECTION
0
TX-
TX+
2
4
6
8
1
3
5
7
5
SHIELD
BI-PHASE DATA CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 15. Bi-Phase Data Communication Wiring
C2649M (9/07)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
AUDIO CONNECTOR
R+
R-
L+
DEVICE A
L-
AUDIO OUT
LEFT
AUDIO OUT
RIGHT
BALANCED AUDIO CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER–
AUDIO CONNECTOR
DEVICE B
AUDIO IN
LEFT
AUDIO IN
RIGHT
R+
R-
L+
L-
BALANCED AUDIO CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 16. Balanced Audio Wiring
28
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
FR106011
RECEIVER –
AUDIO CONNECTOR
DEVICE A
AUDIO OUT
LEFT
R
L
AUDIO OUT
RIGHT
SHIELD
UNBALANCED AUDIO CONNECTIONS BETWEEN DEVICE A AND FR106011 RECEIVER
FT106011
TRANSMITTER –
AUDIO CONNECTOR
DEVICE B
AUDIO IN
LEFT
AUDIO IN
RIGHT
R
L
SHIELD
UNBALANCED AUDIO CONNECTIONS BETWEEN DEVICE B AND FT106011 TRANSMITTER
Figure 17. Unbalanced Audio Wiring
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Troubleshooting
LED indicators on the front panel of the FT106011 transmitter/FR106011 receiver (refer to Figure 2)
allow you to monitor signal status, laser status, data activity, contact closure activation, and operating
guidelines.
Table F. Troubleshooting with Front-Panel Indicators
Indicator Color
Meaning
Possible Cause
Corrective Action
Power LED (Pelco badge)
Blue
Power is being applied
–
No action required.
to the module.
Not lit
Power is not being
applied to the module. faulty.
Power connection is
Check power connection.
If module is rack mounted,
reseat module or power
supply as necessary.
Power supply has failed. Replace power supply.
Loss of power occurs due Check circuit breaker(s),
to tripped circuit
fuse(s), or electrical service
breaker(s), blown fuse(s), as necessary.
or faulty electrical
service.
Contact Closure LED (
)
Amber
Not lit
Contact is closed.
Contact is open.
–
–
No action required.
No action required.
Check connections.
(Continued on next page)
Connections are faulty.
30
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Troubleshooting with Front-Panel Indicators (Continued)
Indicator Color
Meaning
Possible Cause
Corrective Action
Audio Present LED (
)
Green
Audio is being trans-
mitted onto the fiber by
the audio port or is
being received from
the fiber by the audio
port.
–
No action required.
Red
The Audio Select
switch is set to an
invalid position.
The Audio Select switch Ensure that the Audio
is set to any of the Select switch is set to
following positions: 2, 3, position 0 or 1 as desired
4, 5, 6, 7, 8, or 9.
(refer to the Setting the
Impedance Mode section
for detailed information).
Intermittent red
Not lit
An audio overload
condition exists.
The audio input level
exceeds 3.0 Vp-p.
Lower the audio input
level.
Audio is not being
transmitted onto the
fiber by the data port or
is not being received
from the fiber by the
data port.
Audio is not present on
the channel.
No action required.
Audio connection is
faulty.
Check audio connections.
Cable is defective.
Replace cable.
(Continued on next page)
C2649M (9/07)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Troubleshooting with Front-Panel Indicators (Continued)
Indicator Color
Meaning
Possible Cause
Corrective Action
Data Activity LED (
)
Flashing amber
Data is being trans-
mitted onto the fiber by
the data port or is
being received from
the fiber by the data
port.
–
No action required.
Red
The Data Select switch The Data Select switch is Ensure that the Data Select
is set to an invalid
position.
set to position 6, 7, 8,
or 9.
switch is set to the correct
position (refer to the
section for detailed
information).
Not lit
Data is not being
transmitted onto the
fiber by the data port or
is not being received
from the fiber by the
data port.
Data is not present on
the channel.
No action required.
Data connection is faulty. Check data connections.
Data communication
cable is defective.
Replace cable.
(Continued on next page)
32
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Troubleshooting with Front-Panel Indicators (Continued)
Indicator Color
Meaning
Possible Cause
or
Corrective Action
Video Present LED (
)
Green
Incoming video signal
is present on the
channel.
—
No action required.
Red on transmitter
Incoming video signal Video source is not
Check power connection to
the video source.
is not present on the
channel.
powered on.
Video source is not
connected to the
transmitter.
Check BNC connections.
Coaxial cable is
defective.
Replace cable.
Red on receiver
Incoming video signal Optical signal is not
Refer to the Optic Fault LED
is not present on the
channel.
being received from the section in this table.
transmitter. Optic Fault
LED is also red.
Video source is not
powered on.
Check power connection to
the video source.
Video source is not
connected to the
transmitter.
Check BNC connections.
Coaxial cable connected Replace cable.
to the transmitter is
defective.
(Continued on next page)
C2649M (9/07)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Troubleshooting with Front-Panel Indicators (Continued)
Indicator Color
Meaning
Possible Cause
Corrective Action
Optic Fault LED (
)
Green
The optical signal is
being received and
laser is operating
properly.
–
No action required.
Red
The optical signal is
not being received.
Remote fiber module is
not powered on.
Check power connections.
Replace power supply if
necessary.
Fiber optic cable is not
connected.
Check fiber optic
connections.
Fiber optic cable
connectors are dirty or
are damaged.
Clean, polish, or replace
fiber optic cable
connectors as necessary.
Fiber optic cable is
defective.
Replace cable.
A problem exists with
the optical power
budget.
Verify that losses in fiber
optic cable do not exceed
the optical power budget
specification of the fiber
optic link. If the losses do
exceed the optical power
budget, contact Product
Support.
Flashing red
Laser has shut down.
Fiber module is operating Ensure that fiber module
in extreme conditions; for operates according to
example, operating
temperature is below or in the Specifications
above recommended section, and then cycle the
range as stated in the the power. If problem persists,
Specifications section. contact Product Support.
Laser has reached end of Cycle the power. If problem
operating conditions stated
life.
persists, contact Product
Support.
34
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
VIDEO
Number of Channels
Modulation Type
Video Input (FT106011)/
Video Output (FR106011)
1
Pulse code modulation, 10-bit resolution
1.0 Vp-p, 75 ohms, NTSC, PAL, and SECAM
Bandwidth
6.5 MHz
Gain
Unity
Differential Gain
Differential Phase
Tilt
<1%
<0.7°
<1%
Signal-to-Noise Ratio
>70 dB (CCIR weighted)
AUDIO
Number of Channels
Audio Input (FT106011/
Audio Output (FR106011)
Input Impedance
2
2.9 Vp-p maximum
600 ohms or 47K ohms, switch-selectable
Input/Output Connection
Bandwidth
Total Harmonic Distortion
Signal-to-Noise Ratio
Balanced (600 ohms) or unbalanced (47K ohms)
20 kHz
<0.02%
>87 dB
DATA
Number of Channels
Data Communication
1
RS-232, RS-422, RS-485 (2-wire/4-wire), Manchester, Bi-Phase,
Coaxitron
Maximum Baud Rate
500 kbps
CONTACT CLOSURE
Number of Channels
Input
1
Active low
Output
30 VDC, 1 A maximum
Choice of normally open or normally closed
GENERAL
Operating Temperature
Input Power Requirements
LED Indicators
-40° to 167°F (-40° to 75°C)
12 VDC or 24 VAC, 350 mA
Power
Video Present
Audio Present
Data Activity
Contact Closure Activation
Optic Fault
C2649M (9/07)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
8.75” D x 1.08” W x 4.81” H
(22.23 x 2.74 x 12.22 cm)
Unit Weight
MECHANICAL
1.6 lb (0.73 kg)
Connectors
Rack Power/Alarm
Stand-Alone Power
Video
4-pin connector
2-pin connector, screw terminals
BNC
Audio
12-pin connector, tension clamps
8-pin connector, tension clamps
6-pin connector, tension clamps
ST for multimode fiber
Data
Contact Closure
Fiber Optic
ST or FC for single-mode fiber
OPTICAL POWER BUDGET, TRANSMISSION DISTANCE, AND LASER CLASS 1 LIMIT
Optical
Power
Budget
Maximum
Transmission
Distance
Laser
Class 1
Limit*
Compatible
Receiver
Transmitter
Wavelength
Multimode (62.5/125 μm)
22 dB†
22 dB†
6 km (3.7 mi)‡
6 km (3.7 mi)‡
<15.6 mW
<0.78 mW
FT106011MSTR FR106011MSTR
1310 nm
850 nm
Single-Mode (9/125 μm)
38 km (23.6 mi)§
38 km (23.6 mi)§
38 km (23.6 mi)§
38 km (23.6 mi)§
<15.6 mW
<10.0 mW
<15.6 mW
<10.0 mW
FT106011SSTR FR106011SSTR
FT106011SFCR FR106011SFCR
1310 nm
1550 nm
1310 nm
1550 nm
24 dB
24 dB
24 dB
24 dB
*The FT106011 transmitter/FR106011 receiver is classified by the FDA as a Class 1 laser product.
† When using 50/125 μm multimode fiber, subtract 3 dB from the optical power budget.
‡ Maximum transmission distance is limited by fiber bandwidth.
§Maximum transmission distance is based on attenuation of 0.5 dB/km plus a 5 dB buffer for
connector and splice losses.
NOTES:
•
For conformal coated models, replace the first letter F in the model number with the letter C.
The conformal coated version of FT106011MSTR, for example, is CT106011MSTR.
•
For models with higher optical power budgets, contact the factory.
36
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
The materials used in the manufacture of this document and its components are compliant to the
requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste
electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling
this equipment.
C2649M (9/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
•
•
Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products.
Three years on Spectra® IV products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-
2X camera models, which have a five-year warranty.
•
•
•
•
•
•
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
Two years on Spectra III™, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video
products.
•
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco
Pelco c/o Expeditors
3500 Pelco Way
Clovis, CA 93612-5699 USA
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual #
C2649M
Date Comments
9/07 Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, Coaxitron, and Spectra are registered trademarks of Pelco.
Endura, ExSite, and Spectra III are trademarks of Pelco.
DLP is a registered trademark of Texas Instruments, Inc.
©Copyright 2007, Pelco.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Canada Finland France Italy Russia Singapore Spain Sweden
|
|
|
|
|
|
|
|
The Netherlands United Arab Emirates United Kingdom United States
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|