2 3
4
5
6
7
8 9
10
12
1
11
13
P-1001AT
P-2001AT
P-3001AT
Technical
Main Channel Power Output
PMPO,8 Ohms, 1KHz test
THD(1KHz)
1000WX2
<1%
2000WX2
<1%
3000WX2
<1%
20 19
18
17
16 15 14
Normal Load Impedance
8 Ohm
8 Ohm
8 Ohm
Input Sensitivity Impedance
400mV/33k Ohm
6mV/600 Ohm
400mV/33k Ohm
6mV/600 Ohm
400mV/33k Ohm
6mV/600 Ohm
CD/DVD AUX
Microphone
(1) POWER SWITCH
(10) FUNCTION DISPLAYED FLUORESCENT
WINDOW
(11) SUB.OUT VOLUME CONTROL
Press to switch the power unit ON or OFF.
(2) TUNING-
Signal to Noise Ratio
Pure Amplifier
Radio tuning button.Decrements the radio
frequency.
(12) LED DIMMER
76dB
71dB
76dB
71dB
76dB
71dB
Adjusts the blue lights and blue rings.
(3) PREV<
KARAOKE
This knob is used to select the preview
station which have been kept in system.
(13) MASTER VOLUME CONTROL
Adjusts the volume level. Turn the knob.
Clockwise to increase the volume.
Frequency Range
(4) TUNING+
Frequency Response(40Hz-15KHz)
+2dB
+2dB
+2dB
-
-
-
Radio tuning button. Increments the radio
frequency.
(14) ECHO CONTROL
Tone Characteristic(100Hz-10KHz)
Power Requirements
+14dB
+14dB
+14dB
Turn the knob to adjust the MIC echo
level.
-
-
-
(5) NEXT>
This knob is used to select the next station
which have been kept in system.
AC~110V/60Hz AC~220V50Hz
483(W)X300(D)X80(H)mm
6.5kg
(15) MIC TREBLE
Adjusts the treble of MIC.
Dimension
Weight
(6) AM/FM SELECTOR
(16) MIC BASS
6kg
7.2kg
(7) A/B SPEAKERS OUTPUT SELECTOR
Adjusts the bass of MIC.
Three mode
：A、B、A+B
(17) MIC VOLUME
(8) MENU CONTROL
Adjusts the volume level. Turn the knob
clockwise to increase the MIC volume.
This is used to increment and decrement
level for the selected function of Master
Volume , Bass , Treble, Balance
station seek.
，Auto
(18) MIC INPUT JACKS 1&2
KARAOKE MIC connect to these jacks.
※ Specifications subject to change without prior notice
(9) INPUT
This is used to select the input sources:
DVD/CD TUNER IPOD/MP3 AUX
(19) HEADPHONE JACKS
Headphone connect to these jacks.
、
、
、
(20) IPOD/MP3 JACKS
IPOD/MP3 connect to these jacks.
4
3
PDF created with pdfFactory trial version www.pdffactory.com
1、AUTO
Automatically search the single source when power on.
2、CD/DVD
CD/DVD Selector.
3、AUX
AUX Selector.
4、TUNER
TUNER Selector.
5、LOUD
Press the button to correct an unbalance program source.
WARNI NG
6、IPOD/MP3
IPOD/MP3 Selector、
7、AUTO SCAN
1
2
7
8
9
3
4
5
6
10
AM/FM auto scan selector，scan and store stations
automitically. Can store 50 stations.
8、MEMORY
After a station has been found，you can store the station
by pressing the MEMORY button and the screen will
display SAVE.
(6) A SPEAKER OUTPUT TERMINALS
(1)TUNER ANT
Connect your speaker system to
Connect for AM and FM antennas.
9、ST/MONO
Stereo and mono selector.
10、AM/FM
these terminals.
(2) AUDIO INPUT JACKS
(7) B SPEAKER OUTPUT TERMINALS
Connect your the other speaker system(s) to
these terminals.
Connect the audio ouput jacks of
DVD/CD、AUX to these jacks.
AM/FM selector.
11/12、PREV> NEXT<
Stations preview and next selector.
13/14、TUNING> TUNING<
The two keys are used to adjust to the best single of
the stations.
(3) REC.LINE OUTPUT JACKS
(8) COOLING FAN
Connect the RECORD input jacks to
these jacks.
(9) 110V/220V SWITCH
According to power voltage ,push this button
to the station of the110V or 220V.
(4) PRE OUTPUT JACKS
Connect the professional input jacks
to these jacks.
(5) SUB-WOOFER OUTPUT JACKS 1&2
15、TREBLE
16、BASS
17、L/R
Left / Right Balance Control
18、A/B SPEAKER
(10) POWER CORD
Connect to AC 110V/60Hz&220V/50Hz outlet.
Speaker（A/B/A+B） Selector
19、VOL+ VOL-
Master Volume Up And Down
20、MUTE
Mute Selector
Remote Controller Operation
1. Remote controller should be operated within 6
meter and the scope of 30 in front of receiver.
2. Make sure that there is no big obstacle between
remote controller and machine.
3. Remote sensor should be far away
from the light,high amounts of light can affect its performance.
5
6
PDF created with pdfFactory trial version www.pdffactory.com
AM ANTENNA
IPOD or
MP3 input
2 MIC
INPUTS
FM ANTENNA
1. Make sure that all connections are properly connected and the main
volume is set to minimum level before turning on the unit.
2. When more then one pair of speakers are used, (specially the main
speaker output) make sure that the speakers used are of the same
wattage and impedance, otherwise the unit maybe damaged under
high power or long term operation.
WARNI NG
AUX
Power Amp
2 Mono Sub Outputs
3. To avoid humming sounds and unwanted noise, make sure that all the
wires are properly inserted.
CD/DVD
Main Speakers
Power Amp
CD Recorder
4. For speaker cords, strip off the vinyl coating and twist the wire tip.
Push down the pink jack or loosen the screw terminal, before inserting
the wire tip, then fasten it and tighten the screw. Be careful not to let
the wires stick out of the terminal otherwise this may cause a short
circuit when wires of different terminal contact each other.
5. After the unit is turned on, adjust the main volume to the desired level
same is true with the bass and treble volume, etc.
Preamp Out
Power Amp
7
8
PDF created with pdfFactory trial version www.pdffactory.com
|