VOICE OVER IP
USER’S MANUAL
Your User Name:
Your Password:
Your Prefix No.:
Your H323 ID:
Your Extension No.:
PI Gatekeeper IP Address: 4.38.32.22
Download from Www.Somanuals.com. All Manuals Search And Download.
1.VoIP PHONE DIAGRAM
VoIP PHONE PORTS
USER NAME
PI WALNUT
777777
09:00:00
GATEKEEPER ID
TIME
• Phone
• Network In
• Power-In • Network Out
VoIP PHONE BUTTONS
• LED Display
• Menu Keypad
Use “ Func” & “ ” to select
1. Phone Mode
2. Gateway Mode (GW)
• 10 Speed Dials
• Phone Keypad
• Speaker Phone
Speed Dial Button
Phone Book Button
Menu Button
VoIP PHONE MENU KEYPAD
Cancel Button
OK (Confirm)
Message Light
DAM/Message
DAM Setting
(Digital Answering Mechine)
Navigation Button
(up/down and left right)
(Digital Answering Mechine)
to check message
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. INTRODUCTION
Before using VoIPPhone, some setup procedures are required to make the phone work properly.
• When both VoIP Phones have Static IP address, users can dial IP address of VoIP Phone.
• If dynamic IP is used, PI can provide gatekeeper service to assign an extension number for VoIP Phone.
• The VoIP Phone also have gateway function, so user can call from PSTN to VoIP phone, from VoIP
phone to another VoIP, or VoIP to PSTN
PSTN
VoIP
VoIP
PSTN
Internet
• No computer required when using this phone.
• Easy configuration through web browser. (i.e. Internet Explorer, Netscape Navigator)
• Using this VoIP phone as regular phone. (Dial out through PSTN) dial 0 to gain PSTN access.
Ex: if you are calling to 1-800-555-1234, you should dial “ 0 18005551234 #”
• Every VoIP Phone comes with a fixed Extension No. and H323 ID
These settings are used to register to PI’s Gatekeeper. These must not be changed.
These settings can only be viewed and modified through web browser.
You can use this VoIP Phone to make calls with 6 scenario
VoIP PHONE - VoIP PHONE
VoIP PHONE - TELEPHONE (local)
TELEPHONE - VoIP PHONE
VoIP PHONE - VoIP PHONE - TELEPHONE (remote)
TELEPHONE - VoIP PHONE - VoIP PHONE
TELEPHONE (local) - VoIP PHONE - VoIP PHONE - TELEPHONE (remote)
Local VoIP PHONE
Remote VoIP PHONE
For More Setup Function,
please refer to page 19.
REGULAR PHONE
(Local Telephone)
REGULAR PHONE
(Remote Telephone)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. HOW TO SET UP (You can exit the Setup Menu anytime by pressing the “ MENU” key again.)
A. Menu Setup
Must Setup in Order for VoIP Phone to Work Properly
Menu
• Push “Menu” to enter Setup Mode
• Set up the name of the phone
e.g. USA01
• Set up DHCP mode (Enable or Disable switched by <– or –> key)
Leave in Disable mode if you have Static IP Address
For Dynamic IP Address, DHCP must set to Enable.
settings would be automatically set.
• Set up ADSL Dialup mode (for Support PPPoE)
(Enable or disable switched by <– or –> Key)
If you select ADSL Dialup to “ YES” , please refer to Page 6, Note.1.
• Set up the IP Share Address as the default gateway of the PC by using the Virtual IP
address for Internet access.
For IP Sharing, Router’s WAN port should connect to the VoIP Phone’s PC port
• Set up IP address when DHCP is disable
Note*: The default value is 0.0.0.0
While DHCP is Disable, IP address must be entered.
• Set up the router (Default Gateway) IP address when DHCP is disable.
• Setting the router IP to 0.0.0.0 is recommended when connecting in a LAN environment.
The default value is 0.0.0.0; When DHCP is Disable, Router IP must be entered.
• Setup subnet mask when DHCP is disable
• The default value is 255.255.255.0 (class C network)
This value must be on while DHCP is OFF
• Set up DNS (Domain Name Service) Server IP Address.
• This function allow IP Phone to look for default SNTP server by Domain name.
• Set up SNTP (Simple Network Time Protocol)
• This function allow IP Phone to get time from the Internet.
• Set up the date (year/month/day) e.g. 99/11/30
• Set up the time (hour:minute:second) e.g. 15:53:20
Note*: Only needed when SNTP is not available
• Set up the Time Zone
• Enable or Disable Gatekeeper by <– or –> key
If you set Gatekeeper to “ YES” , please refer to Page 6, Note.2.
• Set up the highest priority of the voice codec for this phone.
(G711Alaw/G.711ULaw/G.723.1/G.729) Your could use <–, –> key to choose.
• Set up VoIP Gateway IP address for “shortcut dial”
• If you want to dial to PSTN or phone number, the VoIP gateway IP address has to be set.
• There are total 5 Gateways from 1 to
5
To Dial for Gateway shortcut dial, simply dial “ 1 #” ~ “ 5 #”
NOTE: When Dialing thru Gateway shortcut dial, enter only static IP or use VPN.
• Call waiting between VoIP and PSTN
• Call forward to pre-setting number or IP address.
• If you choose “YES” then you could input the number
a. IP to IP (priority 1); i.e. 4.38.32.22,a remote unit where you want the call forward to.
b. From IP to PSTN (priority 2); i.e. 555-1234, a local phone number
c. From PSTN to IP (priority 3); i.e. 192.168.100.222 forward to this IPif call from PSTN
Enabling this function, only one of the three options will be chosen. If two or more are
selected, only the one with the higher priority will work. For example, if you want to use
PSTN to IP Call, Priority 1 & 2 should be blank.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. HOW TO SETUP (You can exit the setup menu anytime by pressing “ MENU” key again.)
A. Menu Setup Con’t
• Set the Tone among different country tone standard or different brand of PBX.
• Select the country or user define.
• Set the Dial Type of PSTN
• You could use <–, –> key to choose PULSE or DTMF
• The function enable when you don’t press any key after the period of time, it will automati-
cally dial the number.
• Shows the MAC of the machine.
• shows the version of the firmware.
Menu
• When setup complete, press “menu” button again.
• Press <OK> to confirm and save the changes or press <Cancel> to canel all changes
*You can exit the setup menu anytime by pressing “ MENU” key again.
Cancel
OK
NOTE.1: When setting up “ADSL Dialup” or PPPoE function set to “YES”
• ID for ADSL Dialup (Internet User Name)
• Password for ADSL Dialup (Internet Password)
NOTE.2: When set up “Gatekeeper” function set to “YES”
• Set up Gatekeeper (GK) IP Address
• Gatekeeper IP will be supplied from PI and should be set to 4.38.32.22
• PI will preset Ext No (Extension No.) - Do Not Change
This Extension No. act as your VoIP Phone number.
• Gateway prefix number can be set(*see warning) if you have already set up the Gatekeeper
(GK) IP. Once Gateway (GW) prefix has been set, this IP Phone will register as a Gateway in
the Gatekeeper. We do not suggest this function to be used and it should be set blank.
*WARNING: GW Prefix is the Identification or password to your VoIP Phone. By enabling this
function, you will have access to VoIP Phone’s PSTN line. But, if someone else have your
Prefix, they can access an outside line thru your VoIP Phone and may run up your telephone
bill. GW Prefix has a maximum of 16 digit number.
• PI GK (Gate Keeper) can not recognize Internal IP address (i.e. 192.168.XXX.XXX)
• If you have to use any IP Sharing (Router), VoIP Phone must be installed in front of Router.
• You can connect Router’s WAN port to VoIP Phone’s PC Port for IP Sharing.
Internet
Router’s WAN Port
• LAN IN
• PC OUT
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. HOW TO SET UP
B. SPEED DIAL
B-1 Setting the speed dial keys
SPEED DIAL
• Press any buttons from M1 to M10 to select
~
• The system will display the current setting (Blank if no previous setting)
• Using the keypad to input the IP address or Phone Numbers.
For Example: “4 38 32 255 #” for setting up the IP address
“
0 5551234 #” for setting up the telephone Number.
• Press “ OK” to save and quit SPEED Dial Setup Mode.
B-2 Using the Speed Dial Keys
~
• Press any button of the speed dial keys from M1 to M10 to Dial
Note:
• M1~M10 setup enable you to do speed dial on your VoIP PHONE.
• Gateway shortcut dial 1~ 5 allows user to access the VoIP PHONE remotely through regular
telephone or another VoIP PHONE.
The remote user simply connect to VoIP PHONE and dial “ 1 #”
C. HOLD (MUTE)
After pressing the “HOLD” key, both local & remote side of the communication line will only hear the
music playing. (This function only available when codec set as G.723.1 or G.729)
Put on “HOLD” with background music
Press again to stop the function
D. VOLUME ADJUSTMENT
VOLUME
Click ‘SPEAKER’ while
handset is on the hook
Select up/down to set
speaker volume
Pick up the handset,
Select up/down to set
Handset volume
When IP Phone is on
standby mode, Select
up/down to set Ringer
Volume
E. CALL TRANSFER
This function is available only when both phone support H.450 call transfer. Upon placing a phone
call, you can use “call transfer” function to transfer the call to other person. For example: when A is
talking to B. A could press “Flash” key and the display will show “Transfer to”. A can enter the IP
address of C and A will be talking to C. After A hanging up the phone, C can talk with B.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
F. PHONE BOOK
Every record inside the phone book has 2 fields: Name and Phone number
The Name field is the primary key of the record and phone number is the field you can use to
store extension number, phone number or IP address. The phone book records are sorted by
Name automatically. You can perform search, add, delete tasks to update your phone book.
PHONE BOOK
Press “P-Book” key again to
exit phone book mode
Press
Browsing Mode
Use Down Arrow Key
First Record
IP Address
to enter Browsing Mode
Phone No.
IP Address
Use
or
arrow
Input the keyword and the system
will return the record identical
match to the keyword
key to switch between
records.
Phone No.
Press
Use Up Arrow Key
Last Record
Edit Mode
to add new record
to Phone Book
Use Down Arrow Key
New Record
Cancel
Phone Book
OK
Use
or
arrow
Press Cancel or P-Book Key will
return to First Page
key to switch between
stages.
System will dial the number in the
field then quit Phone book Mode
Cancel
Use Up Arrow Key
New Record
The record will be deleted and the
system will return to browsing
mode again.
Press “ ” to quit Phone book edit mode and save the changes
Press “#” to quit Phone book edit mode and ignore the changes.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G. DAM (DIGITAL ANSWERING MACHINE)
DAM/MESSAGE
If there is no message.
If there is any message.
LCD Display
Press OK button to listen to the
messages and then system will
return the previous page without
showing “unread” indication.
Press CANCELbutton to delete
the message
Use
or
arrow
key to switch among
messages.
Press DAM/Message again to exit
the DAM Mode. If there is any
message left unread, LED will
continue flashing.
DAM/MESSAGE
H. DAM SETTING
Note**: Only “OK” key will save the OGM (out going message) in.
When you reboot the IP Phone, the OGM will restore to default message.
Note: After setting up, ‘OK’ have to be pressed in order to save
the setting. When IP phone is turn off or reboot, OGM will
restore to default message.
DAM SETTING
<– Use
or
arrow key
to choose setting
After picking up the handset,
you can start to record the OGM.
Play the OGM then goes back
to “2.Check Message” again
If DAMis enable, LED is ON while
there is unread msg. LED flashes
9
Download from Www.Somanuals.com. All Manuals Search And Download.
I. IP SHARE/NAT - PC COMPUTER
This function allows the VoIP Phone and PC to share the one global real IP address. You may only have one
real IP address assigned by your ISP. With this function we can share one IP address with several PC.
• When “NAT/IP Share” in the VoIP Phone is set as “10.1.1.1”
• The IP address setting for PC is
IP Address: 10.1.1.2~10.1.1.254
Subnet Mask: 255.255.255.0
Default Gateway: 10.1.1.1 (same as IP share address)
• DNS server IP address should be set
(for DNS server IP address please refer to ISP)
Computer
Internet
• LAN IN
PC’s RJ-45
Network Port
• PC OUT
PC NAT Setting
Internet Protocol (TCP/IP) Properties
? X
General
You can get IP settings assigned automatically if your network sup-
ports this capability. Otherwise, you need to ask your network adminis-
trator for the appropriate IP settings.
NAT Setting on VoIP Phone
Obtain an IP address automatically
Use the following IP address:
IP address:
10
255 . 255. 255.
10 1 .
.
1
.
1 .
2
0
1
Subnet mask:
Default gateway:
.
1
.
Obtain DNS server address automatically
use the following DNSserver address:
Preferred DNS server:
Alternate DNS server:
68 .95 . 192.
1
Please Check with your ISP
for your real DNS IP Numbers
Advanced...
OK Cancel
10
Download from Www.Somanuals.com. All Manuals Search And Download.
J. IP SHARE/NAT - ROUTER
First, please setup your Router enable static IP On.
Do not set to Dynamic IP or PPPoE for this setting.
NAT Setting on VoIP Phone
Router
Internet
Router’s
WAN Port
• LAN IN
• PC OUT
Router Setting
Cable/DSL ISP Settings:
Device LAN IP Settings
Please set up the following:
Please set up the following:
IP assigned by your ISP to 10.1.1.2
IP Subnet Mask: 255.255.255.0
The device LAN IP Address and Subnet Mask
IP Address: 192.168.10.1
ISP Gateway Address: 10.1.1.1
IP Subnet Mask: 255.255.255.0
Domain Name Server (DNS) IP Address: 68.95.192.1
Please Check with your
Internet service provider (ISP)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
K. CALL FORWARD
The setting for this Gateway function
• you could use the <–,–> key to enable or disable the Call Forward function
• Set up the IP address for Call Foward from PSTN to IP
• Set up the phone number for Call Forward from IP to PSTN
• Set up the phone number for Call Forward from IP to IP
Use the <–,–> key to enable or disable the Call Forward Function
Set up the phone number for Call Forward from IP to IP
Set up the IP address for Call Forward from PSTNto IP
Set up the phone number for Call Forward from IP to PSTN
• Call forward to pre-setting number or IP address.
if you choose “YES” then you could input the number
• IP to IP (priority 1); (i.e. 192.168.100.200 remote unit where you want the call forward to.)
• From IP to PSTN (priority 2); (i.e. 555-1234 local phone number)
• From PSTN to IP (priority 3); (i.e. 192.168.100.222 forward to this IP if calling from PSTN)
One of the three option can be chosen. If two or more are selected, only the one with higher priority will work.
For example, if you want to use PSTN to IP Call, Priority 1 & 2 should be blank.
L. BUSY TONE SETTING
Since the busy tone might be different from country to country, make sure to set up your IP Phone’s
busy tone for different PSTN environments.
• Select proper tone setup by arrow
• Use the <–,–> key to choose different country.
• Press OK to enter User defined mode, then set up the ms for on/off interval.
Select proper tone setup by
arrow keys
You can use the <–,–> key to
choose different country
Press OK to enter User
defined mode, then set up
the ms for on/off interval.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M. GATEWAY/PHONE MODE
The VoIP Phone supports Gateway mode or Phone mode. Set this IP Phone to Gateway mode
if you want to forward incoming PSTN calls to another IP phone.
Otherwise, set up your IP Phone to Phone Mode.
Press “1” or “2” for phone or
Gateway mode (GW)
Func
Use “Func” then “ ” button to
scroll through the display modes
Use “ Func” then “ ” button to scroll through the display modes
Once the Gateway Set to GW (Gateway) and the Foward function is set off.
Calling to this phone will allow the caller access to dial any outside calls.
If you are calling from a telephone, you will hear “ Please Dial Phone Number at the Tone” .
Dial another VoIP Phone’s IP address or extension number to make the call.
Call from User A to VoIP at Location-1, Location-2, or Any User.
VoIP Phone at Location 1
VoIP Phone at Location 2
User A
Any User
at any location
at any location
PSTN
PSTN
INTERNET
Gateway OFF
When GW (Gateway) is set OFF
VoIP Phone on Location 1 will Ring
When GW (Gateway) is set OFF
VoIP Phone on Location 2 will Ring
Gateway OFF
Gateway ON
When GW (Gateway) is set ON and
security for GW is blank. User A
can gain access to this VoIP Phone
‘s PSTN Line. Therefore just key in
the phone number
Gateway ON When GW (Gateway) is set on
you gain access to this VoIP phone, you will
Security for GW
is blank or not set
hear “please dial phone number at the tone”.
Since PSTN line is in use, you can call other
VoIP Phones
When GW (Gateway) is set ON and
Security for GW is set. User A can
gain access to this VoIP Phone ‘s
PSTN Line after Key in the pass-
word. Therefore just key in the
password and phone number
together.
Security for GW
is set (see NOTE)
1. Shortcut Dial 1~ 5 followed by the”#”
if shortcut dial are set to other VoIP Phone.
2. Dial VoIP Phone’s IP Address.
3. Dial Extension of other VoIP Phone
4. Dial Known GW Prefix to gain access of
another VoIP Phone’s Outside Line.
Gateway Prefix
When GW (Gateway) is set ON and
Prefix is set. Any User call from any
VoIP Phone can dail GW Prefix
number to gain access to this VoIP
Phone’s PSTN Line.
When VoIP Phone on Location 2 is
set to forward. User A will be for-
ward to Preset forwarded Number.
Forward ON
NOTE: Security for GW (Gateway) Password has to set thru the web browser
Easy configuration through web browser. (i.e. Internet Explorer, Netscape Navigator)
Default user name: user
Default password: user
13
Download from Www.Somanuals.com. All Manuals Search And Download.
N. LANGUAGE SELECTION
This Ip Phone supports both English and Japanese, the setup process is as below:
• Press <UP> & <DOWN> to toggle between English and Japanese
• Press <OK> to set the selected language and return to stand-by-mode
Press <Up> & <Down> to toggle
between English and Japanese
Func
Press <OK> to set the selected language
and return to stand-by mode
Use “Func” & “1” button to
enter to the Language
selection mode
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4. HOW TO SET UP VoIP PHONE THRU BROWSER
A. WEB BROWSER CONFIGURATION
Your IP Phone can also be set up by using a web browser, such as “Microsoft IE”, “Netscape”. Key-in http://ip_address:9999
(ip_address is the IP address of the IP Phone) in URL field to get into the web page. If the password is not BLANK, it will pop up
a window for entering the password. You can change settings by click the Hyper-Text in left side of the window. Once completed,
press “Submit” to save the settings or press “Reset” to restore the parameter to the original setting. Note: You have to click
“Submit” before moving to another page, otherwise the settings will be lost. You must reboot your computer to activate any new
settings.
Default User Name: User
Default Password: User
assword field is blank, User Name
ou have to log-in to the browser
me: User; Password: User
are changing the User Name
d should be set also.
r User Name and Password when
his product.
er VoIP Phone’s IP Address
se should be static IPs.
When Call Forward is Enabled
Please choose only one option
either from IP to PSTN, PSTN
to IP or IP to IP. Leave the
other two field blank.
Please leave this field blank.
This number will be shown on
Gatekeeper Server.
This field is your GK password
It is used for the Gatekeeper
service. This password can
only be set in the web browser.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
B. ADVENCED SETTING
Please do NOT change setting
on this page
C. QUICK DIAL SETTING
This is the Quick Dial Setting
You can set it to IP address or
Telephone numbers.
Setting up PSTN or telephone
call, please use “ 0” , phone
number and followed by a #.
Example: 555-1234
Dial “ 0 5551234 #”
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5. HOW TO USE VoIP PHONE
LOCATION A
LOCATION B
LOCATION C
LOCATION D
PSTN
PSTN
Internet
Telephone
(909) 555-4321
REGULARPHONE
(714) 555-1234
VoIP Phone
(909) 555-2222
IP:4.38.32.123
Extension: 6666
GW Prefix: 616161
Shortcut Dials:
1: 4.38.32.223
2: 9999
VoIP Phone
(714) 555-3333
IP: 4.38.32.223
Extension: 9999
GW Prefix: 909090
Shortcut Dials:
1: 4.38.32.123
2: 6666
Your Static IP Address
VoIP Extension No.
Your Gateway Prefix
Your Static IP Address
VoIP Extension No.
Your Gateway Prefix
Example for shortcut dial:
Remote IP Address:
Remote VoIP Extension No.:
Gateway Prefix:
Remote IP Address:
Remote IP Address:
You can set 5 Shortcut Dial which can be
access through PSTN
Example for shortcut dial:
Remote IP Address:
Remote VoIP Extension No.:
Gateway Prefix:
3: 616161
3: 909090
Remote IP Address:
Remote IP Address:
You can set 5 Shortcut Dial which can be
access through PSTN
4: 4.38.32.100
5: 4.38.32.200
GW (Gateway)
Password: 7777
4: 4.38.32.100
5: 4.38.32.200
GW (Gateway)
Password: 6666
Shortcut Dial can be IP Address,
VoIP extension or GW Prefix
Shortcut Dial can be IP Address,
VoIP extension or GW Prefix
A. MAKING A TELEPHONE CALL TO VOIP PHONE
LOCATION A LOCATION B
There are 4 different ways to make a phone call with VoIP Phone
PSTN
• Dial IP address directly “ 4 38 32 250 #” (IP: 4.38.32.250)
or “192 168 100 100 #” (IP: 192.168.100.100) while using VPN
replace “.” with “ ” in the IP address, use # to finish dialing.
• Dial VoIP extension, a free (GK) gatekeeper service provided by PI.
You can dial the extension of another VoIP phone (i.e. “66666 #”)
• Dial through VoIP Phone to telephone when GW (gateway) is enabled.
You can simply dial “ 1” (shortcut dial), password and phone no.
You can store 5 shortcuts “ 1”~“ 5”, they can be IP or VoIP extension.
Regular Telephone
(909) 555-4321
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
• Dialing through regular phone line “ 0 19095983718 #)
Note: Dial “ 0” to access regular phone line.
When making a call from location A to location B
Simply dial “5552222”. Regular Phone on location B will ring.
Pick up handset and you can begin communication.
C. MAKING A REGULAR TELEPHONE CALL
C. MAKING A INTERNET CALL TO VOIP PHONE
LOCATION A
LOCATION B
LOCATION B
LOCATION C
PSTN
Internet
Regular Telephone
(909) 555-4321
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
Telephone No.: (714) 555-3333
IP Address: 4.38.32.223
When making a call from location B to location A
When making a call from location B to location C
Simply dial “ 0 5554321 #”. Regular Phone on location A will ring.
Pick up handset and you can begin communication.
Simply dial “4 38 32 223 #”. VoIP Phone on location C will ring.
Pick up handset and you can begin communication.
Download from Www.Somanuals.com. All Manuals Search And Download.
E. MAKING A PHONE CALL TO ANOTHER VOIP PHONE
LOCATION A LOCATION B
LOCATION C
PSTN
Internet
Regular Telephone
(909) 555-4321
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
Telephone No.: (714) 555-3333
IP Address: 4.38.32.223
If VoIP phone at Location B has set up 4.38.32.223 to its shortcut dial 1. You
can simply dial “ 1 #” after you hear “please dial phone number at the tone”.
VoIP Phone at Location B can also be set up to forward call to Location C. If
Auto forward is set to 4.38.32.223, then User at Location A need only to place
a call to Location B and will be automatically transfered to VoIP Phone at
Location C.
When making a call from location A to location C
VoIP Phone on Location B must set GW (Gateway) ON.
To make a call from Location A to B Simply Dial “5552222”.
You will hear “please dial phone number at the tone”
Dial IP of VoIP Phone Number on Location C “4 38 32 223 #”
C.MAKING A GW CALL FROM ANOTHER VOIP PHONE
LOCATION B
Internet
LOCATION C
LOCATION D
PSTN
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
Telephone No.: (714) 555-3333
IP Address: 4.38.32.223
Regular Telephone
(714) 555-1234
When making a call from location B to location D
If VoIP Phone on Location C have set a GW Prefix. Example 909090.
At the tone, dial “909090 #” wait 2 sec, dial “5551234 #” to call Location D
If you make call to Location C frequently, you can now set shortcut dial 1 to
909090 5551234. And you can now make the call by pressing “ 1 #” or you
can set 1 to 909090 and dial “ 1 5551234 #” after the tone.
Warning : Since GW Prefix doesn’t require password to access your phone.
It’s recommanded to leave it blank in order to prevent unauthorized use of
VoIP Phone. Since Any VoIP phone can call your GW Prefix and gain access
of your PSTN phone lines
VoIP Phone on Location C must set GW enabled
We can set IP address of Location C to shortcut dial from 1~
We can simply set this up to 1 with IP 4.38.32.233
While VoIP Phone’s GW (Gateway) is “ON” at Location C
i. If VoIP Phone on Location C does not have GW password.
You can simply dial “ 1 5551234 #” to call Location D
5
ii. If VoIP Phone on Location C have GW password (example. 7777)
You can simply dial “ 1 7777 5551234 #” to call Location D
F. MAKING A GW CALL FROM REGULAR PSTN PHONE
LOCATION A
LOCATION B
LOCATION C
LOCATION D
PSTN
PSTN
Internet
Regular Telephone
(909) 555-4321
Regular Telephone
(714) 555-1234
Telephone No.: (909) 555-2222
IP Address: 4.38.32.123
Telephone No.: (714) 555-3333
IP Address: 4.38.32.223
When making a call from location A to location D
If VoIP Phone on Location C have a GW Prefix. Example 909090
You (Location A) can call to Location B, after you hear “please dial phone
number at the tone”, dial “909090#” wait 2 sec and dial “5551234 #” to
call Location D. If you make call to Location D frequently, you can now set
short cut dial 1 at Location B to “887766 5551234 #”. And you can
make the call by pressing “ 1 #” at the tone. You can also set 1 to
887766 and dial “ 1 5551234 #” after the tone.
VoIP Phone at Location B must set GW enabled and set up VoIP Phone
at Location C to it’s shortcut dial between 1~
We can set shortcut dial 1 with IP 4.38.32.233
5
While VoIP Phone’s GW (Gateway) is “ON” at Location C.
i. If VoIP Phone on Location C does not have GW password.
You (Location A) can simply dial 555-2222 to call Location B,
After hearing “please dial phone number at the tone”, dial
Warning: Since GW Prefix doesn’t require password to access your phone
It’s recommanded to leave it blank in order to prevent unauthorized use of
VoIP Phone. Since Any VoIP phone can call your GW Prefix and gain
access of your PSTN phone lines.
“
1 5551234 #” Note: dial “ 1” will call to Location C. At location C
because no password required, you can simply enter the phone
number at Location D where you want to call.
ii. If VoIP Phone on Location C have GW password (example. 7777)
You can simply dial “ 1 7777 5551234 #” to call Location D
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SETUP DIAGRAM
Setup Diagram A
You may register to PI Gatekeeper
Setup Diagram B
You may register to PI Gatekeeper
Note 1: PI Gatekeeper is a free service. This free service is dependent on the longevity of each
ISP (Internet Service Provider), network/internet traffic and cost of maintenance. As this is a free
service, PI is not responsible for any liabilities and losses due to any down-time.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Diagram C (Not Recommanded, Professional Installation Required)
PI Gatekeeper does NOT support for this setting.
You can only call to your
internal IP address,
You can only call to your
internal IP address,
Setup Diagram D (Not Recommanded, Professional Installation Required)
PI Gatekeeper does NOT support for this setting.
You can only call to your
statuc IP address,
You can only call to your
static IP address,
Note 1: For setting up as Diagram C,D, Each VoIP PHONE require it’s own static IP address.
Note 2: If dynamic IP, you should used DYNDNS (Dynamic IP Solution) and assign port
1719~1720 and 41000~41001 for VoIP PHONE.
6. ABBREVIATIONS
Gatekeeper:
Gateway:
G723:
G711:
G729A/B:
MAC Address:
ADSL:
CNG:
DAM:
DHCP:
DTMF:
IP:
Asymmetric Digital Subscribe Line
Comfortable Noise Generation
Digital Answering Machine
Dynamic Host Configuration Protocol
Dual Tone Multi-Frequency
Internet Protocol
NAT:
Network Address Translation
Point-to-Point Protocol Over Ethernet
Public Switch Telephony Network
Simple Network Time Protocol
Voice Activate Detection
PI Gatekeeper: 4.38.32.22
PPPoE:
PSTN:
SNTP:
VAD:
If this IP Address does not respond, please visit
to obtain a new gatekeeper IP address.
VoIP:
VPN:
Voice over Internet Protocol
Virtual Private Network
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STATIC IP QUICK SETUP
(You can exit the Setup Menu anytime by pressing the “ MENU” key again.)
Menu
• Push “Menu” to enter Setup Mode
• Set up the name of the phone (e.g. PI WALNUT)
• Skip (Leave as default)
User Name
PI WALNUT
• Skip (Leave as default)
777777
09:00:00
Extension No.
Time
• Skip (Leave as default)
Upon Completion, your LEDDisplay should
contain the following information.
• Set up Your IP address.
• Set up your ISP Gateway Address.
• The default value is 255.255.255.0 (Please check with your ISP)
• Leave as default. (Please check with your ISP)
• Set up SNTP (Simple Network Time Protocol)
• This function allow IP Phone to get time from the Internet.
If you do not know how to set this up. Skip to next step.
• Set up the date (year/month/day) e.g. 99/11/30
• Set up the time (hour:minute:second) e.g. 15:53:20
• Set up the Time Zone
If you do not know how to set this up. Skip to next step.
• Enable or Disable Gatekeeper by <– or –> key
If you want to use the GK (Gatekeeper) please enable this function.
• Enable or Disable Gatekeeper by <– or –> key
If you want to use the GK (Gatekeeper) please enable this function.
• Set up Gatekeeper (GK) IP Address
• Gatekeeper IP will be supplied from PI and should be set to 4.38.32.22
Menu
• To save and exit press “menu” button and then “OK”.
• To cancel and exit press “menu” button and then “Cancel”
Q1
Download from Www.Somanuals.com. All Manuals Search And Download.
DYNAMIC IP QUICK SETUP
(You can exit the Setup Menu anytime by pressing the “ MENU” key again.)
Menu
• Push “Menu” to enter Setup Mode
• Set up the name of the phone (e.g. PI WALNUT)
• Set up DHCP mode to Enable
• Skip (Leave as default)
User Name
PI WALNUT
777777
09:00:00
Extension No.
Time
• Skip (Leave as default)
• Skip (Leave as default)
Upon Completion, your LEDDisplay should
contain the following information.
• Skip (Leave as default)
• Skip (Leave as default)
• Skip (Leave as default)
• Set up SNTP (Simple Network Time Protocol)
• This function allow IP Phone to get time from the Internet.
If you do not know how to set this up. Skip to next step.
• Set up the date (year/month/day) e.g. 99/11/30
• Set up the time (hour:minute:second) e.g. 15:53:20
• Set up the Time Zone
If you do not know how to set this up. Skip to next step.
• Enable or Disable Gatekeeper by <– or –> key
If you want to use the GK (Gatekeeper) please enable this function.
• Enable or Disable Gatekeeper by <– or –> key
If you want to use the GK (Gatekeeper) please enable this function.
• Set up Gatekeeper (GK) IP Address
• Gatekeeper IP will be supplied from PI and should be set to 4.38.32.22
Menu
• To save and exit press “menu” button and then “OK”.
• To cancel and exit press “menu” button and then “Cancel”
Q2
Download from Www.Somanuals.com. All Manuals Search And Download.
ADSL (PPPoE) QUICK SETUP
(You can exit the Setup Menu anytime by pressing the “ MENU” key again.)
Menu
• Push “Menu” to enter Setup Mode
• Set up the name of the phone (e.g. PI WALNUT)
• Set up DHCP mode (Enable or Disable switched by <– or –> key)
Leave in Disable mode if you have Static IP Address
For Dynamic IP Address, DHCP must set to Enable.
• Set up ADSL Dialup mode to YES
• ID for ADSL Dialup (Internet User Name)
• Password for ADSL Dialup (Internet Password)
• Skip (Leave as default)
• Skip (Leave as default)
• Skip (Leave as default)
User Name
PI WALNUT
777777
09:00:00
Extension No.
Time
• Skip (Leave as default)
Upon Completion, your LEDDisplay should
contain the following information.
• Skip (Leave as default)
• Set up SNTP (Simple Network Time Protocol)
• This function allow IP Phone to get time from the Internet.
If you do not know how to set this up. Skip to next step.
• Set up the date (year/month/day) e.g. 99/11/30
• Set up the time (hour:minute:second) e.g. 15:53:20
• Set up the Time Zone
If you do not know how to set this up. Skip to next step.
• Enable or Disable Gatekeeper by <– or –> key
If you want to use the GK (Gatekeeper) please enable this function.
• Set up Gatekeeper (GK) IP Address
• Gatekeeper IP will be supplied from PI and should be set to 4.38.32.22
• PI will preset Ext No (Extension No.) - Please Do Not Change
This allows other VoIP Phone to dial your VoIP Phone by G/K
(Gatekeeper) Extension instead of typing your IP address.
Menu
• To save and exit press “menu” button and then “OK”.
• To cancel and exit press “menu” button and then “Cancel”
Q3
Download from Www.Somanuals.com. All Manuals Search And Download.
By removing this label, you agree to conform
to the conditions below.
PI Gatekeeper is a free service. This free service is dependent on the
longevity of each ISP (Internet Service Provider), network/internet traffic
and cost of maintenance. As this is a free service, PI is not responsible
for any liabilities and losses due to any down-time.
label
Download from Www.Somanuals.com. All Manuals Search And Download.
|