USER
MANUAL
MODEL 2500RC Series
Models 2500RC, 2510RC
and 2520RC:
All-Rate CSU/DSU
Rack Mount Card
SALES OFFICE
(301) 975-1000
TECHNICAL SUPPORT
(301) 975-1007
Part# 07M2500RC--D
Doc# 099011UD
Revised 3/19/97
C
E
R
T
I
F
I
E
D
An ISO-9001
Certified Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 FCC INFORMATION
1.4 SERVICE
All warranty and nonwarranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
The Model 2500 Series has been tested and registered in
compliance with the specifications in Part 68 of the FCC rules. A label
on the equipment bears the FCC registration number. You may be
requested to provide this information to your telephone company.
Your telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the proper
operation of the Model 2500 Series. If this happens, the telephone
company should give you advance notice to prevent the interruption of
your service.
Notice: Packages received without an RMA number will not be
accepted.
The telephone company may decide to temporarily discontinue
your service if they believe your Model 2500 Series may cause harm to
the telephone network. Whenever possible, they will contact you in
advance. If you elect to do so, you have the right to file a complaint
with the FCC.
Patton Electronics' technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Patton Model 2500RC. Technical Service hours: 8AM to 5PM EST,
Monday through Friday.
If you have any trouble operating the Model 2500 Series, please
contact Patton Technical Support at (301) 975-1000. The telephone
company may ask you to disconnect the equipment from the telephone
network until the problem has been corrected or until you are certain
that the Model 2500 Series is not malfunctioning.
The following information may be required when applying to your
local telephone company for leased line facilities:
Service
Digital Facility Service Order Network
Type
Interface Code
04DU5-24
04DU5-48
04DU5-96
04DU5-56
Code
6.0F
6.0F
6.0F
6.0F
Jacks
RJ48S
RJ48S
RJ48S
RJ48S
2.4 Kbps Digital Interface
4.8 Kbps Digital Interface
9.6 Kbps Digital Interface
56 Kbps Digital Interface
NOTE: As of this publication date, 19.2 and 64Kbps digital
services have not been assigned Digital Facility Interface Codes.
1.3 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive and the Low Voltage Directive (LVD) of the Union European
(EU). A Certificate of Compliance is available by contacting Technical
Support.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 GENERAL INFORMATION
2.3 SUPPORTED APPLICATIONS
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is
warranted for One Year parts and labor. If any questions arise during
installation or use of the unit, contact Patton Electronics Technical
The Model 2500RC Series includes three units: the Model 2500RC
All-Rate CSU/DSU, the Model 2510RC Switched 56 CSU/DSU and the
Model 2520RC All-Rate/Switched 56 CSU/DSU. Depending upon the
unit selected, the Mode 2500RC Series supports three distinct modes
of operation. These are outlined in the descriptions and table below:
Dedicated DDS/Clear Channel Operation (Models 2500RC, 2520RC)
The unit can be easily configured for dedicated DDS/Clear Channel
operation by means of the dip switches on the bottom of the enclosure,
or by means of the software control port. Set the Line Rate to match
the rate of service to which you subscribe. Set the Mode switches for
Network Clocking. The Rate Converter and the Data Format options
should be set as required for your application. The remaining options
may need to be set depending on your terminal equipment and your
application.
2.1 PRODUCT FEATURES
• Operates over 4-wire dedicated digital lines
• Supports rates of 56 Kbps and 64 Kbps and all sub rates
• Supports Switched 56 dialing
• Both RS-232 and V.35 rear interface cards available
• Features V.52 and V.54 compliant tests
• Nine easy-to-read LED indicators to monitor data signals
• Internal, external or received loopback clocking
• AT&T 62310 compliant
Switched-56 Operation (Models 2510RC, 2520RC)
The unit can be used in Switched 56 applications. Set the Line
Rate to 56 Kbps. Set the Mode switches for Switched 56, and enable
Force RTS and Circuit Assurance. Dial or store a number using the
control port. The Rate Converter and the Data Format options should
be set as required for your application. The remaining options may
need to be set depending on your terminal equipment and your
application.
• Can be used as a high speed modem for private twisted pair
• Fits in Patton’s rack chassis and Cluster Boxes
• Made in the USA
Campus Area Short Haul Operation (Models 2500RC, 2520RC)
2.2 GENERAL PRODUCT DESCRIPTION
The unit can also be used for campus area point-to-point short-haul
applications on private twisted-pair wires. Set the Line Rates the same
on both units. Set the Mode switch for the appropriate Transmit Clock
Mode for your application. Internal, External and Looped Clock Modes
are available. Set the remaining options as needed by your terminal
equipment or your application.
The Model 2500RC Series CSU/DSUs operate either
synchronously or asynchronously over 4-wire circuits up to 64 Kbps.
Rate conversion allows operation with a variety of DTE devices.
Diagnostics include V.54 and V.52 loopback tests, as well as CSU
loops. Configuration is accomplished by either internal DIP switches or
RS-232 software switches (user provides terminal). Nine easy-to-read
function card LED indicators monitor data and control signals. Two rear
interface cards are available: DB-25 and RJ-48 or M/34 and RJ-48.
MODEL 2500RC SERIES APPLICATIONS
2500RC
2510RC
2520RC
Line Rate Switches
Mode Switches
All line rates
Supported
56 Kbps only
All line rates
Supported
The Model 2500RC Series is AT&T compliant and supports DDS,
Switched 56, Clear Channel 64 and other digital services available from
major service providers including AT&T, Sprint and MCI. Dedicated
models can also be used as a high speed modem for private twisted
pair. The Model 2500RC Series is available in standalone or in rack-
card versions (only rack card versions are covered in this manual).
Supports all modes Switched 56 only
except Sw-56
All modes
Supported
Dialing
Commands
Not Supported
Supported
Supported
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 CONFIGURATION
3.1.1 Switch Set “S1”
Before you can install and operate your Model 2500RC Series
CSU/DSU, you must configure both the front and rear cards. The
Model 2500RC Series has two sets of eight switches (S1 and S2), a
reversible interface driver board and two Rotary Address switches
(MSD and LSD). The 2500RC also has software switches which may
be configured with the Patton Model 1000CC control card (not
supplied), using a VT-100 type RS-232 terminal. Rear card
configuration is accomplished by means of hardware straps.
The configuration switches on switch set S1 allow you to specify
Line Rate, Circuit Assurance, RTS, Character Length, Data Format and
DSR Loop Status. The table below summarizes S1 switch settings,
including the factory defaults. Following the table are descriptions of
each switch setting.
SWITCH SET S1 SUMMARY TABLE
3.1 FRONT CARD CONFIGURATION - HARDWARE SWITCHES
Position
S1-1
S1-2
S1-3
S1-4
S1-5
S1-6
S1-7
S1-8
Function
Line Rate
Factory Default
Exceptions
The Model 2500RC Series front card defaults to the use of
hardware switches for configuration. Hardware switches consist of
two eight-position DIP switches, and two rotary switches (see Figure 1,
below).
Off
56,000 bps
On
Line Rate
}
Line Rate
On
Circuit Assurance
RTS
Off Disabled
Off Forced On
Off 10-Bit
Model 2510:Enabled
Rotary Address
Switches
Interface
Driver
Board
LSD
MSD
Character Length
Data Format
DSR Loop Status
Off Synchronous
Off DSR Off
Switches S1-1. S1-2 and S1-3: Line Rate
SW2
SW1
These switches control the signalling rate on the line or RJ-48S
port of the unit. They should be set to match the speed of your digital
service.
FRONT THIS SIDE UP FOR V.35
S1-1
On
On
On
On
Off
Off
Off
S1-2
On
On
Off
Off
On
On
Off
S1-3
On
Setting
2.4 Kbps
4.8 Kbps
9.6 Kbps
19.2 Kbps
56 Kbps
64 Kbps
Force configuration
pointer to default to
Hardware Switches
(See Section 3.2)
Off
On
Off
On
Off
Off
Figure 1. Model 2500RC Series front card, showing location of switches
The two sets of DIP switches on the Model 2500 Series are referred to
as S1, S2. As Figure 2 shows, the orientation of all DIP switches is the
same with respect to “ON” and “OFF” positions.
ON
ON
For line rates of 56 and 64 kbps, it is possible to operate the DTE
interface at a lower rate. To do this, set these switches to 56 or 64 kbps
and set the Rate Converter/DTE Rate switches as required.
1
2
3
4
5
6
7
8
OFF
Figure 2. Close up of DIP switches showing ON/OFF positions.
NOTE: The ON position is oriented toward the front of the Model 1092RC.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch S1-4: Circuit Assurance
Switch S1-7: Data Format
The transmitter and the CTS output can be configured to go On
only when a working communication circuit is established. If Circuit
Assurance is used, enable it on only one end of the communication link.
Circuit Assurance should be enabled in Switched 56 mode.
The data format selection controls whether an async-to-sync
conversion is performed.
S1-7
On
Data Format
Asynchronous
Synchronous
Circuit
Off
S1-4
On
Assurance
Enabled
Description
CTS will go low and the transmitter
will be held off if the receiver is in
the No Signal state or CD is low
The transmitter and CTS will
operate without regard to the
receiver state
Switch S1-8: DSR System Status
Off
Disabled
The behavior of the DSR output during performance of a local loop
can be controlled.
DSR
S1-8
On
Loop Status
DSR On
Description
DSR remains high (On) during the
Analog Loop
Switch S1-5: RTS
The RTS input can be forced on, ignoring the terminal’s RTS
signal. RTS controls the transmitter by either sending the user’s data
or sending an idle code.
Off
DSR Off
DSR goes low (Off) during the
Analog Loop
3.1.2 Switch Set “S2”
S1-5
Off
RTS
Forced On
Description
An On (high) condition is trans-
mitted regardless of the state of
this unit’s RTS input
The configuration switches on switch S2 control the Rate
Adapter/DTE Rate, Clock Mode, Anti-Stream Timer and RTS/CTS
Delay. The table below shows factory default settings for Switch S2.
Following the table are descriptions of each switch setting.
On
Follows DTE The RTS input controls the
transmitter
SWITCH SET S2 SUMMARY TABLE
Switch S1-6: Character Length
Position
S2-1
S2-2
S2-3
S2-4
S2-5
S2-6
S2-7
S2-8
Function
Rate Adapter
Rate Adapter
Rate Adapter
DTE Loop Control
Clock Mode
Factory Default
Exceptions
Off
In asynchronous data format, 10 and 11 bit characters are
supported. This setting is ignored in synchronous data format.
DTE Rate
Off
}
Off
Character
Length
10-bit
Character Description
Off Disabled
S1-6
Off
Start
Data bits
Parity
None
1
Stop bits
1
1
1
8
7
7
1 or more
1 or more
2
Off
Off
Off
On
Network
Clock
Model 2510
Switched 56
}
}
Clock Mode
None
Anti-Stream Timer
RTS/CTS Delay
On Disabled
On
11-bit
1
1
8
9
1
1 or more
1 or more
Off Normal
None
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Switches S2-1, S2-2 and S2-3: Rate Adapter/DTE Rate
Switch S2-7: Anti-Stream Timer
The Model 2500RC Series includes a rate adapter that allows the
unit to be used with DTE devices that support rates lower than 56/64
kbps. All switch settings below are valid for line rates of 56 or 64 kbps.
The anti-stream timer protects multidrop networks from a drop that
is continuously transmitting. If the terminal keeps RTS raised for more
than 30 seconds, the timer forces RTS off internally. This allows the
rest of the multidrop network to resume operation. The CSU/DSU
remains in the forced-off condition until the terminal drops RTS.
S2-1
On
Off
On
Off
On
Off
S2-2
On
On
Off
Off
On
Off
S2-3
On
On
On
On
Off
Off
DTE Rate
2.4 kbps
4.8 kbps
9.6 kbps
19.2 kbps
Timer Value in Sec at Various Line Rates
S2-7
On
Off
Timer
Disabled
Enabled
56
19.2
9.6
4.8
2.4
2
4
8
15
30
38.4 kbps
Line Rate = DTE Rate
Switch S2-8: RTS/CTS Delay
NOTE: for DTE devices that operate at 57.6 kbps, set the Line
Rate to 56 kbps (see Section 3.1.1 4.1.1), set the rate adapter for
“Line Rate=DTE Rate”, and configure your DTE device for two
stop bits (set character length accordingly).
The RTS/CTS turn-on delay can be set to Normal or Extended.
Delay in mSec at Various Line Rates
S2-8
Off
CTS Delay
Normal
56
0.3
1.3
19.2
0.9
3.8
9.6
1.9
7.5
4.8
3.8
15
2.4
7.5
30
Switch S2-4: DTE Loop Control
On
Extended
The local loop and remote loop can be activated from the DTE
interface using signals “LL” and “RL”.
3.1.3 Setting the Reversible Interface Driver Board
The Model 2500RC Series supports both RS-232 and V.35
S2-4
electrical interfaces for the terminal connection port. Which electrical
interface is active is determined by the orientation of the small
reversible daughter board on the front card (see Figure 3, below). The
daughter board is clearly marked “THIS SIDE UP FOR RS-232” and
“THIS SIDE UP FOR V.35”. Note: When plugging the daughter board
into the socket, the arrow should always point toward the front of the
PC board.
On
Off
Enable LL and RL inputs
Disable
Switches S2-5 and S2-6: Clock Mode
The appropriate transmitter clocking modes can be selected for
Dedicated DDS, Switched-56 or campus-area (private) operation.
S2-5
On
S2-6
Off
Mode
External Clock Mode Transmit Clock
derived from terminal
Description
Interface
Driver
Board
interface
Network Clock Mode Transmit clock derived
(Looped Clock Mode) from the received line
signal; Use this mode
Off
Off
FRONT
THIS SIDE UP FOR V.35
for Dedicated DDS
operation
On
Off
On
On
Internal Clock Mode
Switched 56
Transmit Clock
derived internally
(Model 2510, 2520)
Figure 3. Closeup of Model 2500RC Interface Driver Board
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.4 Setting Rotary Address Switches
2. Power up the terminal and set its RS-232C port as follows:
9600 baud
8 data bits, 1 stop bit, no parity
local echo
CR = CR/LF on inbound data
ANSI, VT-100 emulation
If you plan to use the software control port to configure or dial the
Model 2500RC Series unit, you will need to configure each front card
with a unique address. This is done by using a small screw driver to
set the two rotary switches, as shown in Figure 4, below. The switches
are set individually for a number from 0 - 9, forming a two digit address
(00 - 98). Software commands set to a particular address will be
recognized by the card with that address, and ignored by other cards.
3. Press [CTRL+B] on the terminal, then enter the address of the
card you wish to configure (see Section 3.1.4), and press
[RETURN]. (Note: Do not use the universal address [99].
Configure only one card at a time.) The Model 2500RC Series
Main Menu should then display on the terminal screen (see
below).
Note: Address “99” is universal. All units respond to address “99”
no matter how the rotary switches are set.
Rotary Address
Switches
LSD
MSD
Figure 4. Setting the rotary address switches
3.2 FRONT CARD CONFIGURATION - SOFTWARE SWITCHES
The Model 2500RC Series has an internal control port that allows
software configuration. Control port signals are carried to each card in
the rack along the power bus board inside the rack chassis. Access to
all rack card control ports is provided by a single Patton Model 1000CC
control card. For instructions on installation and use of the Model
1000CC, please refer to the Model 1000CC User Manual.
3.2.2 Using the Software Menu System
The Model 2500RC Series Menu System operates as follows:
1
2
All selections must be followed by [RETURN].
To make a selection from any menu, enter the option number
at the prompt and press [RETURN].
3.2.1 Accessing the Software Control Port
Once you have set each Model 2500RC’s address (see Section
3.1.4), plugged each front card into the rack chassis (see Section 4.0),
and properly installed the Model 1000CC control card (see Model
1000CC User Manual), you are ready to access the Model 2500RC
Series Main Menu. Follow these steps:
3.
To exit any menu without making a selection, press [ESC]
followed by [RETURN]. (Note: You can also exit by just
pressing [RETURN]. However, doing this in the Store Phone
Number Menu will clear the buffer of the currently stored
number.)
1. Connect the serial RS-232C port of a VT100 terminal (or
similar RS-232 DTE with terminal emulation) to the EIA-561
control port on the Model 1000CC control card.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.3 Verifying Software Switch Control
For each screen described below, selecting a numbered option and
pressing [RETURN] stores that option setting and returns you to the
Software Switch Menu (Note: All lettered options must be entered in
lower case)
In order to use software switches for configuration, it is necessary
to disable the hardware switch settings. To do this, use the following
procedure (Note: If this procedure is omitted, your software
configurations will be overridden by the hardware switch settings):
Line Rate
Choosing option 1 in the Software Switch Menu takes you to the
Line Rate Menu (below). This option controls the signaling rate on the
line. Set it to match the speed of your digital service. For line rates of
56 or 64 Kbps, it is possible to operate the DTE interface at a lower
rate. To do this , set the line rate to 56 or 64 Kbps. Then set the DTE
Speed as required (Software Switch Menu option 7).
1. On the Main Menu (opposite page), choose item 1, “Select
Hardware/Software Switch Control”. The following screen will
appear:
2. In the Hardware/Software Control Menu, select item 2 to
enable software switch control.
3. The Main Menu will automatically reappear after your selection
is entered.
Circuit Assurance
3.2.4 Setting Software Switch Parameters
Choosing option 2 in the Software Switch Menu takes you to the
Circuit Assurance Menu (below). On dedicated (DDS) circuits, the
transmitter and the CTS output can be configured to go ON only when
a working communication circuit is established. If you use Circuit
Assurance with DDS services, enable it on only one end of the
communication link. For Switched-56 service, enable Circuit Assurance
on both ends of the circuit. When Circuit Assurance is disabled, the
transmitter and CTS operate without regard to the receiver state.
From the Main Menu, selecting item 3, “Set Software Switch
Parameters” will take you to the Software Switch Menu (below). From
this screen, you can soft configure the 2500RC parameters.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Force RTS
Choosing option 3 in the Software Switch Menu takes you to the
RTS Menu (below). The RTS input can be forced ON, ignoring the RTS
signal from the DTE. When RTS is forced ON, the transmitter is always
enabled and the user may send data. On a Model 2510RC or 2520RC,
RTS should be forced ON for Switched-56 operation.
DTE Data Format
Choosing option 5 in the Software Switch Menu takes you to the
Data Format Menu (below). This option controls whether an async-to-
sync conversion is performed between the DTE and the Model 2500RC
Series. (Data is always transferred synchronously between two Model
2500RC Series units.) For an asynchronous DTE, select the
asynchronous data format1,2; for a synchronous DTE, select the
synchronous data format.
NOTE: When the Line Rate (Software Switch Menu option 1) is 64
Kbps, RTS is always forced ON, regardless of the Force RTS
switch setting.
NOTE1: The async rate of 57.6 kbps is supported at the 56 kbps
line rate, provided the DTE equipment is configured to transmit two
stop bits. The extra stop bit reduces the DTE’s effective data rate
to allow synchronization with the 56 kbps line speed. Set the
Model 2500RC Series for two stop bits by selecting “11 bit
character length” in the Character Length Menu.
Character Length
Choosing option 4 in the Software Switch Menu takes you to the
Character Length Menu (below). In asynchronous data format, the
Model 2500RC Series supports 10-bit and 11-bit character lengths. Set
this option according to the characteristics of the data being
transmitted.
NOTE2: You can use the Model 2500RC Series to transmit lower-
speed asynchronous data (up to 9.6 Kbps) over synchronous
circuits by simple over-sampling. To do this, select the
synchronous data format and set the line Line Rate (Software
Switch Menu option 1) to at least four times that asynchronous
data rate you wish to send. For example, use a Line Rate of 9.6
Kbps or higher for 2.4 Kbps async data.
17
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DSR Status During Local Loopback
NOTE: For DTE data rates of 56 kbps or 64 kbps, set the rate
adapter to “Line Rate = DTE Rate”, and set the Line Rate to 56 or
64 kbps, respectively. For DTE rate of 57.6 kbps, set rate adapter
to “Line Rate = DTE Rate”, set line rate to 56 kbps, set DTE for two
stop bits, and set CSU/DSU character length to “11 bits”.
Choosing option 6 in the Software Switch Menu takes you to the
DSR Loop Status Menu (below). This option controls the behavior of
the DSR output during local loopback. To force DSR high (ON) during
local loopback, enable this option. To force DSR low (OFF) during a
local loopback, disable it.
DTE Loop Control
Choosing option 8 in the Software Switch Menu takes you to the
DTE Loop Control Menu (below). The local and remote loopbacks on
the Model 2500RC Series can be controlled from the DTE interface by
raising or lowering the LL and RL signals. To allow the DTE to control
these loopbacks in this manner, enable this option. Disable if you want
the Model 2500RC Series to ignore these signals.
Rate Converter/DTE Rate
Choosing option 7 in the Software Switch Menu takes you to the
Rate Adapter/DTE Rate Menu (opposite page). The Model 2500RC
Series rate converter adapts a 56 Kbps or 64 Kbps line rate to slower
DTE data rates. Set the Rate Converter to match the DTE data rate. If
the DTE data rate is the same as the line rate, disable rate conversion
by selecting item 6 on this menu.
Clock Mode
Choosing option 9 in the Software Switch Menu takes you to the
Clock Mode Menu (below).
(continued)
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Set this option as follows:
RTS/CTS Delay
Choosing option “b “ in the Software Switch Menu takes you to the
RTS/CTS Delay Menu (below). This option lets you set the RTS/CTS
turn-on delay to Normal or Extended. The delay interval decreases as
the line rate increases.
• Internal (Master): To use the Model 2500RC and 2520RC internal
reference clock as the timing source, select item 1. Use internal timing
in point-to-point applications where the Model 2500RC Series is being
used as a limited distance modem. (Set the far-end Model 2500RC
Series unit for looped timing as described below.)
• Network (Looped): To have the Model 2500RC Series derive a
transmit clock from the incoming data stream from the network, select
item 2. This is the default setting and appropriate for most applications.
(Models 2500RC and 2520RC only)
• External (Terminal Timing): To have the Model 2500RC Series use
the DTE-supplied transmit clock (pin 24 on and RS-232/V.24 interface
or pins U and W on a V.35 interface), select item 3. Use external timing
for tail-circuit applications, in which the RS-232 or V.35 ports of two
Model 2500RC Series units are interconnected.
• Switched 56 (Model 2510RC and 2520RC only): When using a
Model 2510RC or 2520RC with Switched 56 service, select item 4.
Anti-Streaming Timer
Choosing option “a” (options “a” through “e” must be entered in
lower-case letters) in the Software Switch Menu takes you to the Anti
Stream Timer Menu (below). This option lets you enable or disable the
anti-streaming timer, which protects multidrop networks from a drop that
is continuously transmitting. If the DTE asserts RTS for a period of time
exceeding the timer interface, the timer forces RTS off internally. This
allows the rest of the multidrop network to resume operation. The
Model 2500RC Series holds RTS off until the terminal drops RTS. The
timer interval decreases as the line rate increases.
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 REAR CARD CONFIGURATION
3.3.1 Model 1000RCM12548 Strap Settings
The Model 2500RC Series has two interface card options: the
Model 1000RCM12548 (DB-25/RJ-48S) and the Model
1000RCM13448 (M/34/RJ-48S). Each of these options supports one
interface connection and one 4-wire connection. Figure 5 (below)
illustrates the two different interface options for the Model 2500RC
Series.
Figure 7 shows strap locations for the Model 1000RMC12548
(DB-25/RJ-48S) rear cards. These straps determine various grounding
characteristics for the terminal interface and twisted pair lines.
JB3
(peg 1 on top)
JB2
(NOT USED)
Model
Model
1000RCM12548
1000RCM13448
JB4
(peg 1 on left)
Figure 7. DB-25/RJ-48S strap locations
The table below provides an overview of interface strap functions
for the rear interface cards. Following this overview is a detailed
description of each strap’s function.
DB-25 F
M/34 F
Figure 5. Model 2500RC Series interface card options
INTERFACE CARD STRAP SUMMARY TABLE #1
Prior to installation, you will need to examine the rear card you
have selected and make sure it is properly configured for your
application. Each rear card is configured by setting straps located on
the PC board. To configure the rear cards, you must set the
configuration straps. Figure 6 (below) shows the orientation of these
straps. Each strap can either be on pegs 1 and 2, or on pegs 2 and 3.
Sections 3.3.1 and 3.3.2 describe the strap locations and possible
settings for each rear card.
Strap
JB3
Function
Position 1&2
Connected
Connected
Position 2&3
Open*
DTE Shield (Pin1) & FRGND
FRGND & SGND
JB4
Open*
DTE Shield (Pin 1) & FRGND (JB3)
In the connected position, this strap links DB-25 pin 1 & frame
ground. In the open position, pin 1 is “lifted” from frame ground.
JB3
Position 1&2 = DTE Shield (Pin 1) and FRGND Connected
Position 2&3 = DTE Shield (Pin 1) and FRGND Not Connected
Figure 6. Orientation of interface card straps
23
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 INSTALLATION
SGND & FRGND (JB4)
This section describes the functions of the Model 1000R16 rack
chassis, tells how to install front and rear Model 2500RC Series cards
into the chassis, and provides diagrams for wiring the interface
connections correctly.
In the connected position, this strap links DB-25 pin 7 (Signal
Ground) and frame ground. In the open position, pin 1 is “lifted” from
frame ground.
JB4
Position 1&2 = SGND (Pin 7) and FRGND Connected
Position 2&3 = SGND (Pin 7) and FRGND Not Connected
4.1 THE MODEL 1000R16 RACK CHASSIS
The Model 1000R16 Rack Chassis (Figure 9, below) has sixteen
short range modem card slots, plus its own power supply. Measuring
only 3.5” high, the Model 1000R16 is designed to occupy only 2U in a
19” rack. Sturdy front handles allow the Model 1000R16 to be
extracted and transported conveniently.
3.3.2 Model 1000RCM13448 Strap Settings
Figure 8 shows the strap location for the Model 1000RCM13448
(M/34/RJ-48S) rear card. This strap determines whether Signal Ground
and Frame Ground will be connected.
JB4
(peg 1 on left)
Figure 9. Model 1000R16 Rack Chassis with power supply
4.1.1 The Rack Power Supply
The power supply included in the Model 1000R16 rack uses the
same mid-plane architecture as the modem cards. The front card of
the power supply slides in from the front, and the rear card slides in
from the rear. They plug into one another in the middle of the rack.
The front card is then secured by thumb screws and the rear card by
conventional metal screws.
Figure 8. M/34/RJ-48 strap locations
SGND & FRGND (JB4)
In the connected position, this strap links Signal Ground and frame
ground.
WARNING! There are no user-serviceable parts in the
power supply section of the Model 2500RC Series.
Voltage setting changes and fuse replacement should only
be performed by qualified service personnel. Contact
Patton Electronics Technical support at (301)975-1007 for
more information.
JB4
Position 1&2 = SGND and FRGND Connected
Position 2&3 = SGND and FRGND Not Connected
(continued)
26
25
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 OPERATION
Switching the Power Supply On and Off
Once the Model 2500RC Series unit is installed and configured
properly it is ready to operate. This section describes the function of
the LED indicators, the status displays, the use of loopback test modes,
and Switched 56 dialing procedures (Models 2510RC and 2520RC
only).
The power switch is located on the front panel. When plugged in
and switched on, a red front panel LED will glow. Since the Model
1000R16 is a "hot swappable" rack, it is not necessary for any cards to
be installed before switching on the power supply. The power supply
may be switched off at any time without harming the installed cards.
5.1 LED DESCRIPTIONS
NOTE: Please refer to the Model 1000RP Series User Manual AC
and DC Rack Mount Power Supplies for fuse and power card
replacement information.
The Model 2500RC Series is equipped with nine LED indicators that
monitor the status of communication. Figure 12 (below) shows the
location of the LEDs on the Model 2500RC Series front panel. Note
also the location of the test mode switches and RS-232 control port
(used in Switched 56 dialing as well as software configuration).
Following Figure 12 is a description of each LED’s function.
4.2 INSTALLING THE MODEL 2500RC SERIES INTO THE CHASSIS
The Model 2500RC Series is comprised of a front card and a rear
card. The two cards meet inside the rack chassis and plug into each
other by way of mating 50 pin card edge connectors. Use the following
steps as a guideline for installing each Model 2500RC Series into the
rack chassis:
•
“TD” and “RD” will glow red to indicate an Idle condition or
Binary “1” data on the respective terminal interface signals.
Green indicates Binary “0” data.
1. Slide the rear card into the back of the chassis along the metal
rails provided.
2. Secure the rear card using the metal screws provided.
Model 2500RC
3. Slide the card into the front of the chassis. It should meet the
rear card when it’s almost all the way into the chassis.
DTR
Power
TD
4. Push the front card gently into the card-edge receptacle of the
rear card. It should “click” into place.
RD
CTS
OS
CD
5. Secure the front card using the thumb screws.
NS
NOTE: Since the Model 1000R16 chassis allows “hot
swapping” of cards, it is not necessary to power down the rack
when you install or remove a Model 2500RC Series.
TM
ER
Remote
Analog
511
511/E
4.3 WIRING THE MODEL 2500RC SERIES
Each of the rear interface cards compatible with the Model 2500RC
Series has one terminal interface port and one 4-wire (twisted pair)
port. For specific interface pin-outs, refer to the diagrams in
Appendix D of this manual.
Figure 10. The Model 2500RC Series' front panel LEDs
(continued)
28
27
Download from Www.Somanuals.com. All Manuals Search And Download.
•
“CTS” will glow green to indicate an On condition. When on,
the unit is ready to send data. If CTS remains off, check the
Forced RTS, Circuit Assurance and Anti-Stream settings.
5.2.1 Displaying Configuration Settings
To display the current settings of the hardware and /or software
switches, go to the Main Menu and select item 2, “Read Configuration”.
This will take you to the Read Configuration Menu (below).
•
•
•
“CD” will glow green to indicate that a valid carrier is present.
If CD is not lit, there is no valid carrier signal detected.
“DTR” will glow green to indicate that the DTR signal from the
terminal is active.
“NS” will glow red to indicate No Signal. This means the
Model 2500RC Series receiver does not detect a signal from
the digital service provider (or, in the case of short-haul
operation, from the remote Model 2500RC Series). If NS is lit,
check for an unplugged cable, broken wire or an incorrect Line
Rate selection.
In the Read Configuration Menu, you may select item 1 to read the
hardware switch configuration or item 2 to read the software switch
configuration. A sample screens is shown below:
•
•
•
“OS” glows red to indicate Out-of-Service. This means the
Model 2500RC Series has received an Out-of-Service signal
from the digital service provider and indicates a problem with
the service provider’s equipment. If this condition persists,
contact your service provider.
“ER” glows red to indicate that an Error has been detected in
the received signal. ER will flash if the Model 2500RC Series
receives illegal bi-polar violations or framing errors. During the
511 or 511/E test, ER will flash to indicate that the Test Pattern
Detector has detected a bit error.
“TM” glows red to indicate Test Mode. It will light if the unit is
placed into a test mode. The unit can be placed in test mode
by the local user, by the remote user or by the service
provider.
5.2 STATUS DISPLAYS
The Model 2500RC Series lets you use a VT-100 type RS-232
terminal to display the current configuration settings, as well as the
line/loop status.
Important: Please be sure you have read Section 3.2, and the Model
1000CC User Manual before attempting to implement the instructions
in the remainder of Section 5.2.
(continued)
30
29
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.2 Displaying Line/Loop Status
LAL Test Activation
To check the current status of the Model 2500RC Series and the
associated circuit, go to the Main Menu and select item 4, “Display
Line/Loop Status”1,2 . This will take you to a screen similar to the
Line/Loop Status Monitor Screen (below).
The LAL test may be activated in one of three ways:
1.
2.
Toggle the front panel “Local/Normal/Remote” switch to the
right hand side to the “Local” position.
Activate the LL lead from the DTE (Note: in order to use this
option, the DTE Loop Control option must be enabled–see
Section 3.2.4). If you are not sure which pin is the LL lead,
please refer to the pinout diagrams in Appendix D.
3
From a terminal, first go to the Main Menu and select item 3 to
display the Software Switch Menu (Section 3.2.4) In the
Software Switch Menu, select item “e” to go to the Local Line
Loop Menu (see below). To activate LAL, select item 1.
NOTE1: To refresh the display with the most up-to-date
information, key “4” and press [RETURN].
NOTE2: The error count is reset after each time it is displayed.
5.3 LOOPBACK TEST MODES
The Model 2500RC Series offers three loopback tests to evaluate
the condition of the CSU/DSUs and the communication link: local
analog loopback, remote digital loopback and telco loopback (C.O.
Loopback).
LAL Test Procedure
Once LAL is activated, the Model 2500RC Series transmit output is
connected to its own receiver. The “Test” LED should be lit. Follow
these steps to complete the test:
5.3.1 Local Analog Loopback (LAL)
1.
Verify that the data terminal equipment is operating properly
and can be used for a test. If a fault is indicated, call a
technician or replace the unit.
The Local Analog Loopback (LAL) test checks the operation of the
local Model 2500RC Series. Any data sent to the local Model 2500RC
Series in this test mode will be echoed (returned) back to the user
device. For example, characters typed on the keyboard of a terminal
will appear on the terminal screen (see Figure 11, below).
2.
Perform a BER (bit error rate) test on each unit using a
separate BER tester (The Model 2500RC Series has a built-in
BER tester–see Section 5.4). If the BER test equipment
indicates no faults but the data terminal indicates a fault, follow
the manufacturer's checkout procedures for the data terminal.
Also, check the interface cable between the terminal and the
Model 2500RC Series.
CSU/DSU
Figure 11. Local analog loop
31
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.2 Remote Digital Loopback (RDL)
RDL Test Procedure
Once LAL is activated, the “Test” LED should be lit. Perform a BER
(bit error rate) test on the system, using BER testers on both ends. If
the BER test equipment indicates a fault and the Local Analog
Loopback test was successful for both Model 2500RC Series units, you
may have a problem with the line between the CSU/DSUs. You should
inspect the line for proper connections.
The Remote Digital Loopback (RDL) test checks the performance of
both the local and remote Model 2500RC Series', and the
communication link between them. Any characters sent to the remote
Model 2500RC Series in this test mode will be returned back to the
originating device. For example, characters typed on the keyboard of
the local terminal will appear on the local terminal screen after having
been passed to the remote Model 2500RC Series and looped back
(see Figure 12, below).
5.3.3 Telco Testing
CSU/DSU
The digital service provider’s central office can perform CSU Loop
and DSU Loop diagnostic testing. These diagnostics allow the central
office to evaluate circuit operation without making visits to a customer’s
premises.
Digital Network
Figure 12. Remote digital loop
CSU Loop
The CSU Loop is activated when the central office reverses the DC
sealing current that flows between the TX pair and the RX pair. In this
case, the Model 2500RC Series recognizes this and loops signals on
the RX pair back to the central office on the TX pair (see Figure 13,
below). While the CSU Loop is activated by the central office, the TM
light is illuminated.
RDL Test Activation
The RDL test may be activated in one of three ways:
1) Toggle the front panel “Local/Normal/Remote” switch to the left
hand side to the “Remote” position.
2) Activate the RL lead from the DTE (Note: in order to use this
option, the DTE Loop Control option must be enabled–see
Section 3.2.4). If you are not sure which pin is the RL lead, please
refer to the pinout diagrams in Appendix D.
DSU
CSU
Digital Network
Figure 13. CSU loop
3) From a terminal, first go to the Main Menu and select item 3 to
display the Software Switch Menu (Section 3.2.4) In the
Software Switch Menu, select item “d” to go to the Set
Remote Digital Loop Menu (see below). To activate RDL, select
item 1.
DSU Loop
The DSU Loop is activated when the central office sends a DSU
loop signal over the twisted pair wire. The Model 2500RC Series
senses this signal and loops the digital data back to the central office
(see Figure 14, below). While the DSU Loop is activated, the TM light
is illuminated.
Digital Network
DSU CSU
Figure 14. DSU loop
33
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 THE V.52 BER TEST PATTERN GENERATOR
5.5 SWITCHED 56 DIALING COMMANDS (MODELS 2510RC &
2520RC)
The Model 2500RC Series has a built-in test pattern generator and
detector. It can be invoked at both ends of a link simultaneously (using
two operators) or it can be invoked in conjunction with the LAL or RDL
tests (using one operator). The following example requires two
operators–one to initiate and monitor the test at the local Model
2500RC Series, and one at the remote Model 2500RC Series. To use
the V.52 BER test by itself, both operators should simultaneously follow
these steps:
CAUTION! For proper Switched 56 operation, you must enable
the Circuit Assurance and Force RTS options as described in
Section 4.0. Failure to do so may prevent the Model 2500RC
Series unit from answering incoming Switched 56 calls.
To access the Switched 56 dialing capabilities of the Mode 2500RC
Series, go to the Main Menu (see Section 3.2.4) and select item 5, “Set
Switched 56 Dialing Parameters”. This will take you to the Switched 56
Menu (see below). The following paragraphs describe the commands
in the Switched 56 Menu.
1. Locate the “511/511E” toggle switch on the front panel of the
Model 2500RC Series and move it to the left hand side (see
Note 1). This activates the V.52 BER test mode and transmits
a “511” pseudorandom test pattern to the other unit. If any
errors are received, the receiving CSU/DSU’s red “Error” LED
will blink sporadically (see Notes 1 & 2, below).
2. If the test indicates no errors are present, move the V.52
toggle switch to the right hand side, activating the “511/E” test
(see Note 2). The 511/E test transmits the 511 pseudorandom
test pattern and injects intentional errors about once per
second. If the test is working properly, the receiving
CSU/DSU’s red “Error” LED will blink regularly. A successful
“511/E” test will confirm that the link is in place, and that the
Model 2500RC Series’ built-in “511” generator and detector
are working properly.
NOTE1: The 511 BER pattern can also be activated using the
software control port. Follow these steps: From a terminal, first go
to the Main Menu and select item 3 to display the Software Switch
Menu (Section 3.2.4) In the Software Switch Menu, select item “c”
to go to the Send 511 Pattern Menu (see below). To send a 511
pattern, select item 1.
Store Phone Number (Enable DTR Dialing)
Selecting item 1 in the Dial Menu lets you activate the Model
2500RC Series’ “DTR Dialing” feature by storing a phone number in the
unit’s non-volatile memory. The Model 2500RC Series automatically
dials this number when the DTE raises the DTR lead. When you issue
this command, the Model 2500RC Series responds with this prompt:
NOTE2: Control Port activation of the “511E” pattern is not
possible. The “511E” pattern may only be activated using the front
panel toggle switch.
Enter up to 12 digits (without hyphens or other alphabetic characters),
followed by [RETURN]. For example: “13015551212.”
CAUTION! Pressing [RETURN] by itself will erase any
previously stored number from the unit’s non-volatile memory
and cannot be undone. This will also disable DTR dialing.
NOTE: To disable DTR dialing, press [RETURN] (and nothing
else) when asked to enter the number to be stored.
35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
SPECIFICATIONS
Read Stored Number
Selecting item 2 in the Dial Menu lets you view the phone number
currently stored in the Model 2500RC Series non-volatile memory.
DDS Type:
Dedicated
Transmission Format:
Interface:
Asynchronous, synchronous
Dial New Number
Selecting item 3 in the Dial Menu lets you dial a number other than
the one stored in non-volatile memory. When you select this menu
item, the Model 2500RC Series responds with this prompt:
RS-232 and V.35
Standards:
AT&T 62310 compliant
2.4, 4.8, 9.6, 19.2, 56 and 64 Kbps
DDS Line Rates:
DTE Rates:
2.4, 4.8, 9.6, 19.2, 38.4, 56, and 64
Kbps; 57.6 Kbps, async, 2 stop bits
Enter up to 12 digits (without hyphens or other alphabetic characters),
followed by [RETURN]. For example: “13015551212.”
Control Port:
Configuration and diagnostics
4-wire
After dialing the number, the Model 2500RC Series will display the
message, “Dialing” and then display each number as it is dialed. The
Model 2500RC Series will then prompt the user to wait while the
connection is made. One of the following messages will then be
displayed to indicate the success or failure or the connection:
Transmission Line:
Applications:
DDS point-to-point or multipoint;
campus-area point-to-point
•
•
CONNECT: The called unit has answered.
Indicators:
LED indicators for TD, RD, CTS, CD,
DTR, No Signal, Out-of-Service, Error
and Test Mode
NO WINK: The central office did not send a wink signal
within 5 seconds of line seizure.
•
•
•
SHORT WINK: A wink signal less than 120 milliseconds
was received.
Diagnostics:
V.54 compliant local and remote
loopback tests; V.52 compliant
511/511E BER test, TELCO CSU and
DSU loops
LONG WINK: A wink signal greater than 320 milliseconds
was received.
NO CARRIER: The called unit did not answer within 30
seconds.
Connectors:
Power Supply:
Dimensions:
DB-25 and M/34
115V or 230V AC
7.3” x 6.6” x 1.6”
•
•
DTR OFF: DTR must be on to dial.
OFF HOOK: The Model 2500RC Series is already off-hook
and in data mode.
NOTE: The control port will not respond to additional commands
until one of the above response messages is issued.
Model 2500RC Series Distance Table (miles)
Wire Gauge
Data
Rate
22
7.1
7.6
24
4.9
5.2
6.2
7.7
26
3.4
3.6
4.5
5.8
9.7
9.1
64 Kbps
56 Kbps
19.2 Kbps
9600 bps
4800 bps
2400 bps
Hang Up
Selecting item 4 in the Dial Menu terminates the call.
8.7
10.4
13.7
15.1
10.6
14.2
37
38
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
CABLE RECOMMENDATIONS
APPENDIX C
FACTORY REPLACEMENT PARTS
AND ACCESSORIES
The Patton Model 2500RC Series operates at frequencies of 20kHz
or less and has been performance tested by Patton technicians using
twisted-pair cable with the following characteristics:
Patton Model #
Description
10-2500RC......................DDS Cable, RJ48 - RJ48, 6 foot
10-561S...........................Control Port Cable, EIA-561, 6ft, shielded
12M-561 ..........................Adapter, EIA-561 to DB-25 Male
12F-561...........................Adapter, EIA-561 to DB-25 Female
082R2..............................Fuse 5x20mm, 200mA, 250V, Time-lag
Little Fuse P/N 239.200
Wire Gauge
Capacitance
Resistance
19 AWG
22 AWG
24 AWG
83nf/mi or 15.72 pf/ft.
83nf/mi or 15.72 pf/ft.
83nf/mi or 15.72 pf/ft.
.0163 Ohms/ft.
.0326 Ohms/ft.
.05165 Ohms/ft.
1000RPEM......................120/240V Rear Power Entry Module
1000RPSM-2 ..................120/240V Front Power Supply Module
1000RPEM-DC................DC Rear Power Entry Module
1000RPSM-48A ..............48V Front Power Supply Module
1000RPEM-V ..................120/240V CE Compliant Rear Power
Entry Module
To gain optimum performance from the Model 2500RC Series,
please keep the following guidelines in mind:
• Always use twisted pair wire—this is not an option.
1000RPSM-V ..................120/240V CE Compliant Front Power
Supply Module
• Use twisted pair wire with a capacitance of 20pf/ft or less.
• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher
AWG numbers than 26)
0805US ...........................American Power Cord
0805EUR.........................European Power Cord CEE 7
0805UK ...........................United Kingdom Power Cord
0805AUS.........................Australia/New Zealand Power Cord
0805DEN.........................Denmark Power Cord
0805FR............................France/Belgium Power Cord
0805IN.............................India Power Cord
• Use of twisted pair with a resistance greater than the above
specifications may cause a reduction in maximum distance
obtainable. Functionality should not be affected.
• Many environmental factors can affect the maximum distances
obtainable at a particular site. Use the above data rate/distance
table as a general guideline only.
0805IS.............................Israel Power Cord
0805JAP..........................Japan Power Cord
0805SW...........................Switzerland Power Cord
39
40
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX D
(APPENDIX D - Continued)
INTERFACE PIN ASSIGNMENT
DDS INTERFACE
The DDS Interface is an RJ-48S modular jack.
DB-25 CONNECTOR, TERMINAL INTERFACE
Pin #
1
Signal
Frame Ground
Pin #
Signal
2
TD
1
2
3
4
5
6
7
8
TX+
TX-
3
4
5
6
7
8
15
17
18
20
21
24
25
RD
RTS
CTS
DSR
no connection
no connection
no connection
no connection
RX+
SGND (Signal Ground)
CD
TC
RC
LL (Local Loop)
DTR
RL (Remote Loop)
XTC
RX-
M/34 CONNECTOR, TERMINAL INTERFACE
Pin #
B
Signal
SGND (Signal Ground)
TM (Test Mode)
C
RTS
D
CTS
CONTROL PORT INTERFACE
E
DSR
F
CD
8 Position modular connector compliant with EIA-561.
H
DTR
L
LL (Local Loop)
Pin #
Signal
M
N
P
TM (Test Mode)
RL (Remote Loop)
TD
4
5
6
Signal Ground
RD (Output)
TD (Input)
R
RD
S
T
U
V
TD/
RD/
XTC
RC
W
X
Y
XTC/
RC/
TC
AA
TC/
41
42
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX E
TRANSMITTER CLOCK SOURCE DURING TEST LOOPS
Dear Valued Customer,
Thank you for purchasing Patton Electronics products! We do
Analog
Loop
Originating
Remote Loop Remote Loop
Receiving
appreciate your business. I trust that you find this user manual helpful.
Clock Mode Normal
We manufacture one of the widest selections of data communications
products in the world including CSU/DSU's, network termination units,
powered and self-powered short range modems, fiber optic modems, interface
converters, baluns, electronic data switches, data-line surge protectors,
multiplexers, transceivers, hubs, print servers and much more. We produce
these products at our Gaithersburg, MD, USA facility, and can custom
manufacture products for your unique needs.
Internal
External
Network
INT
EXT
RC
INT
INT
INT
INT
EXT
RC
RC
EXT
RC
RC = Received Clock
We would like to hear from you. Please contact us in any of the
following ways to tell us how you like this product and how we can meet your
product needs today and in the future.
Web:
(301) 975-1000
(301) 975-1007
(301) 869-9293
Sales E-mail:
Support E-mail:
Phone - Sales
Phone - Support
Fax:
Mail:
Patton Electronics Company
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
We are committed to a quality product at a quality price. Patton
Electronics is BABT and ISO 9001 certified. We meet and exceed the highest
standards in the industry (CE, UL, etc.).
It is our business to serve you. If you are not satisfied with any
aspect of this product or the service provided from Patton Electronics or its
distributors, please let us know.
Thank you.
Burton A.Patton
Vice President
P.S. Please tell us where you purchased this product.
Copyright ©
Patton Electronics Company
All Rights Reserved
_________________________________________________________
43
Download from Www.Somanuals.com. All Manuals Search And Download.
|