Patton electronic Network Card 1007 User Manual

USER  
MANUAL  
MODEL 1007 and  
1007S  
Mac Short Range Modem  
SALES OFFICE  
(301) 975-1000  
TECHNICAL SUPPORT  
(301) 975-1007  
Part# 07M1007-A  
Doc# 082012UA  
Revised 3/24/94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.0 INSTALLATION  
RJ-11  
SIGNAL  
RJ-45  
SIGNAL  
The Model 1007 is easy to install. This section tells you how to  
properly connect the Model 1007 to the twisted pair interface and Mac  
phone port, and how to operate the Model 1007.  
1----------------GND†  
2----------------RCV-  
3----------------XMT+  
4----------------XMT-  
5----------------RCV+  
6----------------GND†  
1----------------N/C  
2----------------GND†  
3----------------RCV-  
4----------------XMT+  
5----------------XMT-  
6----------------RCV+  
7----------------GND†  
8----------------N/C  
3.1 CONNECTION TO THE TWISTED PAIR INTERFACE  
The Model 1007 supports data-only communication between a  
Mac and another serial device. There are two requirements for instal-  
lation:  
When connecting two Model 1007s, it is necessary to use a  
“crossover” cable. The diagram below shows how a crossover cable  
should be constructed for an environment where both Model 1007s  
use a 4-wire RJ-11 connector. Similar logic should be followed when  
using an RJ-45 connector or a combination of the two.  
1. These units work in pairs. You must have one Model 1007 (or a  
compatible model) at each end of the two twisted pair cable.  
2. To function properly, the Model 1007's modular jacks must be con-  
nected to two twisted pairs of metallic wire. The pairs must be  
unconditioned, dry metallic wire, between 19 and 26 AWG (the  
higher number gauges may limit distance). Standard dial-up tele-  
phone circuits, or leased circuits that run through signal equaliza-  
tion equipment are not acceptable.  
SIGNAL PIN# COLOR‡  
COLOR  
PIN# SIGNAL  
GND†  
RCV-  
XMT+  
XMT-  
RCV+  
GND†  
1
2
3
4
5
6
Blue --------------------White  
6
4
5
2
3
1
GND†  
XMT-  
RCV+  
RCV-  
XMT+  
GND†  
Yellow------------------Red  
Green ------------------Black  
Red---------------------Yellow  
Black -------------------Green  
White-------------------Blue  
For your convenience, the Model 1007 is available with two differ-  
ent twisted pair interfaces: an RJ-11 jack or an RJ-45 jack.  
3.1.1 TWISTED PAIR CONNECTION USING RJ-11 OR RJ-45  
Connection to ground is optional  
Standard color codes—yours may be different  
The Model 1007's RJ-11 and RJ-45 connectors on the twisted pair  
interface are pre-wired for a standard TELCO wiring environment (see  
Figure 1). The table on the following page describes the signal/pin  
relationships.  
3.2 CONNECTION TO THE MAC PHONE PORT  
The Model 1007 should be connected to your Mac through the  
1 foot extension cable. Simply plug one end of the cable into the  
Model 1007 and the other end directly into the phone (serial) port of  
your Mac. The pin-outs are listed below.  
1 - Blue  
1 - Blue  
2 - Orange  
2 - Yellow  
3 - Green  
4 - Red  
3 - Black  
4 - Red  
5 - Green  
6 - Yellow  
7 - Brown  
8 - Slate  
Serial Port Pinout (RJ-45)  
5 - Black  
6 - White  
1
2
3
4
5
6
7
8
=
=
=
=
=
=
=
=
N/C  
HSKi (Handshake In)  
HSKo (Handshake Out)  
Ground  
RD- (Receive Data -)  
TD- (Transmit Data -)  
N/C  
Figure 1. AT&T standard modular color codes  
N/C  
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A  
Mini Din 8 to RJ-45 Cable  
Din 8 RJ-45  
SPECIFICATIONS  
Signal  
Transmission Format: Asynchronous  
1---------------3 --------------HSKo (Handshake Out)  
2---------------2 --------------HSKi (Handshake In)  
3---------------6 --------------TD (Transmit Data)  
4---------------4 --------------Gnd (Ground)  
5---------------5 --------------RD (Receive Data)  
6---------------4 --------------TD+(Transmit Data)  
7 -------------N/C-------------GPi  
Data Rate: 0 to 19,200 bps  
Surge Protection: 600W power dissipation at 1 mS and response  
time of 1.0 pS (Model 1007S only)  
Distance: See below  
8 -------------N/C-------------RD+ (Receive Data)  
Control Signal: The single Mac control line, Handshake In, turns  
on when the modem is connected  
TD+ is connected to ground  
Distance: See table below  
3.3 OPERATING THE MODEL 1007  
Transmit Line: 4 wire, unconditioned line (2 twisted pairs)  
Transmit Mode: Full duplex, 4-wire  
Transmit Level: 0 dBm  
Once the Model 1007 is properly installed, it should operate trans-  
parently—as if it were a standard cable connection. Operating power  
is derived from the Mac's data and control signals; there is no  
“ON/OFF” switch.  
Line Connection: RJ-11, RJ-45  
Power Supply: None required, uses ultra low power from data and  
control signals  
Size: 2.0” x 1.7” x 0.8”  
Distance Table (miles)  
Wire Gauge  
Data Rate  
19  
6.2  
7.5  
8.7  
11.8  
17.0  
24  
3.7  
4.9  
5.6  
8.0  
26  
1.2  
2.5  
3.7  
4.9  
8.0  
19,200  
9,600  
4,800  
2,400  
1,200  
11.8  
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B  
BLOCK DIAGRAM  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  

NETGEAR Network Router XM128 ISDN User Manual
NETGEAR Switch GSM7224 User Manual
Nikon Camcorder COOLPIXS9100BLK User Manual
Onkyo Speaker System HTP 520 User Manual
Optoma Technology Projector EP910 User Manual
Overland Storage Stroller S81 T R2 4 10 User Manual
OWI Speaker V6715 User Manual
Panasonic Car Stereo System CQ 5251JU User Manual
Panasonic Cordless Telephone KX TCD650E User Manual
Panasonic Headphones KX TD7580 User Manual