Patton electronic Film Camera 2113 User Manual

USER

MANUAL

MODELS 2113 & 2115

CopperLink™-T

T1/E1 Extenders

Important—This is a Class A device and is

intended for use in a light industrial environ-

ment. It is not intended nor approved for use

in an industrial or residential environment.

Part# 07M2113-UM

Doc# 03331U2-001,

Rev. B

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Revised 8/16/07

An ISO-9001Certiﬁed

Company

Download from Www.Somanuals.com. All Manuals Search And Download.

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 2113 or 2115 components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the ﬁrst date of the shipment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modiﬁcation. If this

product fails or does not performs as warranted, your sole recourse shall

be repair or replacement as described above. Under no condition shall

Patton Electronics be liable for any damages incurred by the use of this

product.These damages include, but are not limited to, the following: lost

proﬁts, lost savings and incidental or consequential damages arising

from the use of or inability to use this product. Patton Electronics spe-

ciﬁcally disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

Note Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 RADIO AND TV INTERFERENCE

This equipment generates and uses radio frequency energy, and if not

installed and used properly—that is, in strict accordance with the manu-

facturer's instructions—may cause interference to radio and television

reception. This equipment has been tested and found to comply with the

limits for a Class A computing device in accordance with the speciﬁca-

tions in Subpart B of Part 15 of FCC rules, which are designed to provide

reasonable protection from such interference in a commercial installa-

tion. However, there is no guarantee that interference will not occur in a

particular installation. If the equipment causes interference to radio or

television reception, which can be determined by disconnecting the

cables, try to correct the interference by one or more of the following

measures: moving the computing equipment away from the receiver, re-

orienting the receiving antenna, and/or plugging the receiving equipment

into a different AC outlet (such that the computing equipment and

receiver are on different branches).

1.2 CE DECLARATION OF CONFORMITY

We certify that the apparatus identiﬁed in this document conforms to the

requirements of Council Directive 1999/5/EC on the approximation of the

laws of the member states relating to Radio and Telecommunication Ter-

minal Equipment and the mutual recognition of their conformity.

Download from Www.Somanuals.com. All Manuals Search And Download.

The safety advice in the documentation accompanying this product shall

be obeyed. The conformity to the above directive is indicated by the CE

sign on the device.

1.3 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green, European Compliance Services Limited.

Oakdene House, Oak Road , Watchﬁeld, Swindon, Wilts SN6 8TD, UK

1.4 FCC PART 68

This equipment complies with Part 68 of FCC rules and the requirements

adopted by ACTA. On the bottom side of this equipment is a label that

contains—among other information—a product identiﬁer in the format

US: AAAEQ##TXXXX. If requested, this number must be provided to the

telephone company.

The method used to connect this equipment to the premises wiring and

telephone network must comply with the applicable FCC Part 68 rules

and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone

company will notify you in advance that temporary discontinuance of ser-

vice may be required. But if advance notice isn’t practical, the telephone

company will notify the customer as soon as possible. Also, you will be

advised of your right to ﬁle a complaint with the FCC if you believe it is

necessary.

The telephone company may make changes in its facilities, equipment,

operations or procedures that could affect the operation of the equip-

ment. If this happens the telephone company will provide advance notice

in order for you to make necessary modiﬁcations to maintain uninter-

rupted service.

If trouble is experienced with this equipment, for repair or warranty infor-

mation, please contact our company. If the equipment is causing harm to

the telephone network, the telephone company may request that you dis-

connect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the

state public utility commission, public service commission or corporation

commission for information.

1.5 INDUSTRY CANADA NOTICE

This equipment meets the applicable Industry Canada Terminal Equip-

ment Technical Speciﬁcations. This is conﬁrmed by the registration num-

ber. The abbreviation, IC, before the registration number signiﬁes that

Download from Www.Somanuals.com. All Manuals Search And Download.

registration was performed based on a Declaration of Conformity indicat-

ing that Industry Canada technical speciﬁcations were met. It does not

imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain

telecommunications network protective, operational and safety require-

ments. The Department does not guarantee the equipment will operate

to the user's satisfaction. Before installing this equipment, users should

ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed

using an acceptable method of connection. In some cases, the com-

pany’s inside wiring associated with a single line individual service may

be extended by means of a certiﬁed connector assembly (telephone

extension cord).The customer should be aware that compliance with the

above condition may not prevent degradation of service in some situa-

tions. Repairs to some certiﬁed equipment should be made by an autho-

rized maintenance facility designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment malfunc-

tions, may give the telecommunications company cause to request the

user to disconnect the equipment. Users should ensure for their own pro-

tection that the ground connections of the power utility, telephone lines

and internal metallic water pipe system, are connected together. This

protection may be particularly important in rural areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.6 COMPLIANCE

EMC

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

Safety

• UL 60950-1/CSA C22.2 N0. 60950-1

• IEC/EN60950-1

• AS/NZS 60950-1

PSTN Regulatory

• FCC Part 68

• CS03

• TBR12 & 13

• AS/ACIF S016:2001

• AS/ACIF S043:2003

1.7 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container. This

number may be obtained from Patton Electronics Technical Services at:

• Telephone: +1 (301) 975-1007

• Email: [email protected]

• URL: http://www.patton.com

Technical support is available from 8 AM to 5 PM EST (8:00 to 17:00

UTC-5), Monday through Friday.

Note Packages received without an RMA number will not be

accepted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alternate Patton support for Europe, Middle East, and Africa

(EMEA)

• Telephone support: Standard telephone support is available ﬁve days

a week—from 8:00 am to 5:00 pm CET (0900 to 1800 UTC/GMT)—

by calling +41 (0)31 985 25 55

• Fax: +41 (0)31 985 25 26

1.8 SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. The

equipment shall be returned to Patton Electronics for

repairs, or repaired by qualiﬁed service personnel.

• The external AC adaptor shall be a listed limited

power source that incorporates a disconnect device and

shall be positioned within easy reach of the operator.

Ensure that the AC power cable meets all applicable

standards for the country in which it is to be installed,

WARNING

and that it is connected to a wall outlet which has earth

ground.

• Do not work on the system or connect or disconnect

cables during periods of lightning activity.

In accordance with the requirements of council direc-

tive 2002/96/EC on Waste of Electrical and Electronic

Equipment (WEEE), ensure that at end-of-life you sepa-

rate this product from other waste and scrap and deliver

to the WEEE collection system in your country for recy-

cling.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.0 GENERAL INFORMATION

Thank you purchasing this Patton Electronics product. This product has

been thoroughly inspected and tested and is warranted for one year for

parts and labor. If questions arise while installing or using this product,

contact Technical Support at +1 (301) 975-1007.

2.1 FEATURES

• Easy-to-install T1/E1 Extenders—no conﬁguration required

• Data rates up to 2.048 Mbps in 64-kbps intervals

• Plug ‘n’ Play for easy installations

• LED indicators for Power, Ethernet Link, and Frame

• CE marked

2.2 DESCRIPTION

The Patton Electronics Model 2113/2115 CopperLink™-T provides high

speed 2-wire T1/E1 extension connectivity to ISPs, PTTs, and enterprise

environments using binder group friendly TC-PAM modulation.

Line connection is made with an RJ-45 jack. Models 2113 and 2115 are

nally-accessible DIP switches, loopback diagnostics, and CopperLink™-

T Plug ‘n’ Play.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.0 INSTALLATION

Because the CopperLink-T T1/E1 Extenders require no conﬁgur ation, they

can be installed quickly. Installation consists of the following:

• Connect the power plug (refer to section 3.1, “Connecting Power” on

page 10).

• Connect the line port (refer to section 3.3, “Connecting the Line Port”

on page 11)

Note See Figure 1 and Figure 2 for the rear-panel connectors

locations.

• Connect the T1/E1 port (refer to section 3.4, “Connecting the Circuit

Interface” on page 11).

Made in the USA

Line

Interface

TX (75 Ohm)

E1 interface

(Data to

Power

(120 Ohm)

G.703/G.704

network)

RX (75 Ohm)

Power

(Data from

G.703/G.704

network)

Figure 1. CopperLink-T Model 2113 rear panel

Made in the USA

Line

Interface

T1 interface

(RJ-48C)

Power

Figure 2. CopperLink-T Model 2115 rear panel

Download from Www.Somanuals.com. All Manuals Search And Download.

3.1 CONNECTING POWER

The external AC adaptor shall be a listed limited power

source that incorporates a disconnect device and shall

be positioned within easy reach of the operator. Ensure

that the AC power cable meets all applicable standards

for the country in which it is to be installed, and that it

is connected to a wall outlet which has earth ground.

CAUTION

Your CopperLink-T T1/E1 Extender comes with an external AC adaptor

with a detachable power cord.

To connect power to the CopperLink-T:

1. Connect the female plug of the AC power cord to the AC adaptor

provided.

2. Connect the barrel-type connector of the AC adaptor to the Power

connector on the CopperLink-T.

3. Insert the male plug of the AC power cord into the AC power outlet

(100-240 VAC).

4. Verify that the Power LED on the front panel illuminates and remains

lit.

3.2 POWER INPUT CONNECTOR

The CopperLink-T T1/E1 Extender comes with an AC power supply.

• The supplies connection to the CopperLink-T T1/E1 Extender is a

2.5 mm barrel receptacle with the center conductor positive (see

Figure 3).

Figure 3. Power connection barrel receptacle diagram

• CopperLink-T T1/E1 Extender’s rated voltage: 5.0 VDC

• CopperLink-T T1/E1 Extender’s rated current: 1 A DC

External AC universal power supply

• Output from power supply: 5 VDC, 2A

• Input to power supply: universal input 100–240 VAC 50/60 Hz 0.3A

Download from Www.Somanuals.com. All Manuals Search And Download.

The interconnecting cables shall be acceptable for

external use and shall be rated for the proper applica-

tion with respect to voltage, current, anticipated tem-

perature, ﬂammability, and mechanical serviceability.

CAUTION

3.3 CONNECTING THE LINE PORT

Follow the steps below to connect the CopperLink-T line port:

1. Obtain a single-twisted pair cable with an RJ-45 plug connector at

each end.

2. Plug one end of the cable into the RJ-45 socket (labeled Line) on the

CopperLink-T .

3. When the remote and local extender units synchronize, the front-

panel Link LED will turn on.

3.4 CONNECTING THE CIRCUIT INTERFACE

Your CopperLink-T comes with either an RJ-48C or an RJ-48C and dual

BNC for connection to a T1 or E1:

• Model 2113 - E1: 120-Ohm RJ-48C and dual 75-Ohm BNC connec-

tors

• Model 2115 - T1: RJ-48C

To connect the twisted pair cable to the CopperLink-T T1/E1 port:

1. Attach the male connector of the twisted pair cable to the female RJ-

48 connector on the CopperLink-T.

2. Attach the other end of the cable to the RJ-48 connector on the local

T1 or E1.

Note When attaching the 2113/2115 directly to a T1/E1 circuit,

a straight through twisted pair cable can be used. When

attaching the 2113/R or 2115/R to a device, please use

the enclosed T1/E1 cross over cable for proper operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note The unit marked as 2113/L or 2115/L is conﬁgured by

default to accept timing from the T1/E1 circuit. The 2113/

R or 2115/R unit then recovers this timing from the line in

order to ensure synchronization of the T1/E1 circuit over

the extenders.

Model Number

Gaithersburg, Maryland

CopperLink-T T1/E1 Link Extender

Power Input 5VDC, 0.5A

(P) Prod: 2113/L/EUI

(S) Serial Nbr: 0000000000

Lot: M00000

Firm Rev: 1.0.0

Complies with FCC Part 15, Class A and FCC Part 68

Registration No.: 1X1XXXXX111

Patton Electronics

Made in the USA

Figure 4. The label showing the speciﬁc model number on the bottom of the unit

Download from Www.Somanuals.com. All Manuals Search And Download.

4.0 OPERATION

Once the CopperLink-T T1/E1 Extenders are properly installed, they

should operate transparently. No user settings required. This section

describes reading the LED status monitors.

4.1 FRONT PANEL LED STATUS MONITORS

Models 2113 and 2115 feature three front-panel LEDs that monitor power,

Ethernet signals, and the CopperLink connection. Figure 5 shows the front

panel location of each LED. Table 1 describes the LED functions.

CopperLink™-T

T1/E1 Link Extender

Frame

Link

Frame

LED

Link

LED

Power

LED

Figure 5. CopperLink-T T1/E1 Extender front panel

Table 1: Front panel LED description

LED

Description

Power

Link

When lit, indicates the unit is powered on

• On solid—link is connected

• Off—No signal detected

• Flashing — Data is being transmitted/received

Frame

• On solid—T1/E1 frame is connected

• Off — No signal detected

• Flashing — Error detected

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2 CONFIGURATION AND DIP SWITCHES

The CopperLink-T™ T1/E1 Extenders are Plug ‘n’ Play enabled and do

not require any conﬁguration by the user.

Note The user should NOT change any of the dip switches except

for S1-7 (if necessary). If the user changes the position of any of

the dip switches (except for S1-7), it will affect the operation of

the unit. Refer to Appendix B on page 17 for the factory default

dip switch conﬁguration.

Switch S1-7: Line Build Out

Switch S1-7 deﬁnes the shape of the waveform on the T1 or E1 line.

Table 2: S1-7 Default Position

Switch 2113/L/EUI 2113/R/EUI 2115/L/EUI 2115/R/EUI

S1-7

OFF (120)

ON (0.0dB) ON (0.0dB)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX A

SPECIFICATIONS

A.1 CIRCUIT RATES

• Model 2113 - 2.048 Mbps

• Model 2115 - 1.544 Mbps

A.2 CIRCUIT INTERFACE

• E1 (Model 2113) presents G.703/G.704 interface. Either 75 Ohms (unbal-

anced) or 120 Ohms (balanced). Pins 1 & 2 are Receive. Pins 4 & 5 are

transmit.

• T1 (Model 2115) present T1 interface. Pins 1 & 2 are Receive. Pins 4 &

5 are Transmit.

A.3 CIRCUIT DEFAULTS

• E1 Line Coding = HDB3.

• T1 Line Coding = B8ZS; Line Build Out Rx = Automatic; Line Build Out

Tx = 0.

A.4 CIRCUIT CONNECTOR

• Dual BNC and RJ48C (Model 2113), strap selectable

• RJ48C connector (Model 2115)

A.5 LED INDICATORS

• Three LED indicators: Power, Link, Frame

A.6 POWER AND POWER SUPPLY SPECIFICATIONS

• AC power supply

• Connection to the CopperLink-T T1/E1 Extender requires +5VDC ±5%

DC power (1.0A minimum). Center pin is +5V.The barrel type plug has

a 2.5/5.5/10mm I.D./O.D./shaft length dimensions

• CopperLink-T T1/E1 Extender’s rated voltage: 5.0 VDC

• CopperLink-T T1/E1 Extender’s rated current: 1A DC

Download from Www.Somanuals.com. All Manuals Search And Download.

A.7 ENVIRONMENTAL

• Temperature: 32–122°F (0–50°C)

• Relative Humidity: 5–95%, non-condensing

• Altitude: 0–15,000 ft (0–4,572 m)

A.8 TRANSMISSION LINE

• Single Twisted Pair

A.9 LINE CODING

• TC-PAM (Trellis Coded Pulse Amplitude Modulation)

A.10 LINE INTERFACE

• Transformer coupled, 2500 VRMS isolation

A.11 LINE PHYSICAL CONNECTION

• RJ-45, 2-wire polarity insensitive pins 4 and 5

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX B

FACTORY DEFAULT DIP SWITCH CONFIGURATION

Note This information is provided for informational purposes only.

These settings should not be changed other than by instructions

from Patton Support, lest the unit be rendered inoperable.

B.1 SWITCH S1 - FACTORY DEFAULT CONFIGURATION

Table 3: S1 Factory Default Dip Switch Conﬁguration

Switch

2113/L/EUI 2113/R/EUI 2115/L/EUI 2115/R/EUI

Switch 1-1

Switch 1-2

Switch 1-3

Switch 1-4

Switch 1-5

Switch 1-6

Switch 1-7

Switch 1-8

OFF

B.2 SWITCH S2 - FACTORY DEFAULT CONFIGURATION

Table 4: S2 Factory Default Dip Switch Conﬁguration

Switch

2113/L/EUI 2113/R/EUI 2115/L/EUI 2115/R/EUI

Switch 2-1

Switch 2-2

Switch 2-3

Switch 2-4

Switch 2-5

Switch 2-6

Switch 2-7

Switch 2-8

OFF

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

_________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

_________________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

_________________________________________________________

Patton Electronics Company

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Oven H 4744 BP User Manual
Nikon Camcorder S6200 User Manual
Nikon Digital Camera 13311 User Manual
Niles Audio Fan FM 1 User Manual
Nintendo Video Games 45496742133 User Manual
Omega Vehicle Security Computer Monitor CNiTH 16D AL User Manual
Omnimount TV Mount 1004409 User Manual
Oster Convection Oven OTM1101VBS User Manual
Panasonic Drill EY7410 User Manual
Panasonic Medical Alarms ESB91 User Manual