O W N E R ' S
M A N U A L
PAL-280 Precision Architectural Loudspeakers
www.parasound.com
Download from Www.Somanuals.com. All Manuals Search And Download.
For best performance and easier troubleshooting, always “home run” wiring when installing
multiple speakers rather than connecting from one speaker to the next. When connecting
multiple speakers, make sure that the power amplifier is capable of adequately driving the
combined impedance of the speakers. If not, you may need additional amplifiers or an
impedance protection device that are often built into loudspeaker selection boxes.
Mirror Image Tweeter Assembly
The PAL-280 tweeter assembly is mirror imaged so you can position them for best sonic
imaging. Ideally, the listening position should be at one point of an equilateral triangle with
the left and right speakers positioned at the other two points. If you need to mount the speakers
outside this idealized equilateral triangle, position the tweeters toward the middle. If you need
to mount the speakers inside this idealized equilateral triangle, position the tweeters toward
the middle.
Installing the PAL-280 Precision Architectural Loudspeakers
1. Confirm that there is at least 1 1/2" of clearance between each edge of the planned
cutout and adjacent studs or joints.
2. Fasten the supplied cardboard template to the wall or ceiling with tape or thumbtacks.
Check again for equal distance of both speakers from the ceiling or floor.
3. Use a level or the included template’s self-leveling feature to so the cutout will be level.
4. Trace around the perimeter of the template.
5. Before making the final cutout, make a small 6-inch square “test cutout” in the center of
the penciled outline. Reach inside the test hole to verify that there are no obstructions in
the way of your planned cutout.
6. Before cutting the hole, first score the drywall with a razor knife and use a keyhole saw
to complete the cut. Remove debris from the edge of the hole.
7. Secure the speaker wire to a stud near the cutout so its weight will not tug on the terminals
of the speaker after it is connected. This also keeps the wire from dropping behind the
wall before you can connect it.
8. Terminate the speaker wire with 1/4" spade lugs or banana plugs. You can also insert
bare wire up to AWG 12 into the holes on the sides of the binding posts.
9. Carefully separate the removable bezel from the baffle and loudspeaker assembly. The
bezel can be mounted in the wall and painted if desired while the main part of the
loudspeaker is stored away safely until you are ready to mount it. Note: The grilles
should be painted separately rather than while mounted in the separate bezel.
10. Insert the PAL-280 bezel into the cutout to make sure it fits easily without forcing.
11. Evenly tighten the mounting screws on the bezel. The mounting “swing-arms” (also known
as mounting “dogs”) will automatically swing out 90 degrees. After they swing out, the
arms then clamp against the drywall from behind the wall.Avoid using excessive force to
prevent deforming the drywall or cracking the speaker’s mounting frame.
12. We recommend that you add a “blanket” of sound absorbing material such as ceiling
insulation behind the woofer to reduce sound transmission into the adjoining room.
Additionally, any sound leakage from behind the molded frame can be blocked with
foam weather-stripping directly behind the plastic speaker bezel.
13. Install the main loudspeaker assembly into the bezel.
14. Install the six rubber shoulder washers into the holes in the bezel
15. Use the six supplied #8 x ∫” screws to fasten the loudspeaker assembly into the bezel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Drilled Hole for Infrared Receivers
The PAL-280 has a 1/2" hole in the bezel to accommodate an infrared receiver such as the
Xantech Video Link model 490. The hole can be accessed by removing the rubber bushing
from the rear of the bezel. If you plan to hide an infrared receiver behind the loudspeaker
grille, be sure to pre-wire a three conductor control wire along with the speaker wire.
Removing the Loudspeaker Assembly from the Bezel
Gently push the lower portion of the pivoting midrange and tweeter assembly until it is at
its full 15-degree downward position. This allows access for your fingers to reach inside
the baffle and loudspeaker assembly and pull it away from the bezel.
Adjusting the Pivoting Midrange and Tweeter Assembly
The PAL-280 employs a pivoting midrange and tweeter assembly.You can adjust this assembly
so the midrange and tweeter are pointing toward the listening position regardless of how the
PALis mounted in the wall. Gently push upper or lower portion of the pivoting midrange and
tweeter assembly to aim it at the desired position.
Fine Tuning the Frequency Response of Your Loudspeakers
Three Position Treble Adjustment
High
The PAL-280 treble adjustment switch allows you to adjust the tweeter level from 0 dB (flat)
to -3 dB or + 3 dB. If you are mounting the speaker in a “live” room with many reflective
surfaces, you may want to attenuate the treble response and tame sibilance. If you are mounting
the speaker in a room with many absorptive surfaces, you may want to boost the treble response.
Two Position Mid-Bass Contour Adjustment
Mid
Bass
The PAL-280 mid-bass adjustment switch allows you to attenuate the mid-bass response
from 0 dB (flat) to -3 dB. If you mounted the PAL-280 near a corner of a wall, you may notice
additional boominess of the bass response. You can attenuate the mid-bass response by setting
the Mid Bass switch to the -3 dB position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Swing arms in locked
and mounted position
Swing arms in
retracted position
PAL-280 Removable Bezel
Tone Adjustment Switches
P
A L - 2
8
0
P
r
e c i s i o n A r c h
i
t
e c t
u
r
a
l
L o u
d
s p e a k e r
High
Aluminum
Tweeter
Mid
Bass
Pivoting Tweeter Assembly
Kevlar Woofer
with Phase Plug
IR Receiver Access Hole
PAL-280 Baffle and Driver Assembly
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PAL-280 Precision Architectural Loudspeaker Specifications
Frequency Response
40 Hz-22 kHz +/- 2 dB
Nominal Impedance
Minimum Impedance
Sensitivity 1 Watt/1Meter
RMS Power Range
Woofer Size
6 Ohms
4 Ohms
89 dB
10-100 Watts
8"
Cone Material
Kevlar
Surround Material
Tweeter Size
Polyurethane
1 " Aluminum Dome
Pivoting Chamber for Lower Crossover Point
2.4 kHz
Tweeter Assembly
Crossover Frequency
Crossover Slope
12 dB per octave
Dimensions
Hole Cut-Out
8 5/8" x 12 3/4"
10" x 14"
Outer Edge of Frame
Optional Accessories
Rough-In Kit
NC/K-8M
Parasound Products, Inc. 950 Battery Street, San Francisco, CA 94111
Features and Specifications Subject to Change Without Notice
© 2000 Parasound Products, Inc. Rev 0.9
Download from Www.Somanuals.com. All Manuals Search And Download.
|