LP5 LEG PRESS 5
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
ASSEMBLY INSTRUCTIONS
CLASS H
PART# 7357701
REV.B
1
Version: LP5A-101
Revision: 11/08/02
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody LP5 Leg Press. Please read these
instructions thoroughly and keep them for future reference.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Tools Required forAssembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
DESCRIPTION
FRAME
KEY
PART #
ACU04-1444
ACU04-1447
ACU04-1449
ACU04-1445
ACU04-1446
ACU04-1448
ACU02-1298
ACU07-0135
ACUDA1E03830016NB
QTY
QTY
KEY
10
11
12
13
14
15
DESCRIPTION
3/8” FLATWASHER
3/8” LOCK NUT
PART #
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
2
6
8
2
4
4
1
4
2
1
ACUDC1250100020B
ACUDB2E03811000B
ACUDA1E02143413NB
ACUDB2E01212000B
ACU11-0080
SEATADJUST
HANDLE
1/2 X 4-3/4” BOLT
1/2” LOCK NUT
MAINARM
SECONDARM
FOOTPLATE
PULLEYBRACKET
PAD
SPRING PIN KNOB
3/4 X 4” SHAFT
ACU05-0372
16
BUMPER, 1-1/2 X 2
SETSCREW, M4X0.7X6L
ACU06-0437
17
ACUDACM04006007YB
3/8 X 3” BOLT
NOTE: Some of the component may be pre-assembled.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
For assembly to the GS1, GS2, GS4, GS8 Gym Systems .
4
Make sure MAIN ARM
is orientated correctly
9−1/2"
5
16
15
1
13
12 1/2 X 4-3/4”
FIGURE 1
STEP 1:
• NOTE: Follow STEP 1 for the assembly of the LEG PRESS to the GS1, GS2, GS4 and GS8 Gym Systems. If you have the CM3 or GS6
Gym System proceed to STEP 2.
• NOTE: FLANGEBEARINGSSHOULDBEPRE-INSTALLED
• SECURELY assemble the SECONDARM (5) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15)
and one 1/2” LOCK NUT (13). See FIGURE 1.
• SECURELY assemble the MAINARM (4) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), two 3/4” FLANGE BEARINGS (14), one
3/4 X 4” SHAFT (15) and one 1/2” LOCK NUT (13). See FIGURE 1. (NOTE: Make sure MAINARM is orientated correctly, top hole
should be 9-1/2” from the top of arm as shown in FIGURE 1.)
• SECURELY assemble two 1-1/2 X 2 “ BUMPERS (16) to each side of the MAINARM (4) where the MAINARM (4) contacts the FRAME
(1) See FIGURE 1.
• Proceed to to STEP 3.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For assembly to the CM3 and GS6 Gym System .
4
11−1/4"
Make sure MAIN ARM
is orientated correctly
5
16
15
1
13
12 1/2 X 4-3/4”
FIGURE 2
STEP 2:
• NOTE: Follow STEP 2 for the assembly of the LEG PRESS to the CM3 and GS6 Gym System. If you have the GS1, GS2, GS4 or GS8
Gym Systems proceed to STEP 3.
• NOTE: FLANGE BEARINGS SHOULD BE PRE-INSTALLED
• SECURELY assemble the SECONDARM (5) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15) and one
1/2” LOCK NUT (13). See FIGURE 2.
• SECURELY assemble the MAINARM (4) to the FRAME (1) using one 1/2 X 4-3/4” BOLT (12), one 3/4 X 4” SHAFT (15) and one 1/2”
LOCK NUT(13). See FIGURE 2. (NOTE: Make sure MAINARM is orientated correctly, top hole should be 11-1/4” from the top of arm
as shown in FIGURE 2.)
• SECURELY assemble two 1-1/2 X 2 BUMPERS (16) to each side of the MAINARM (4) where the MAINARM (4) contacts the FRAME
(1) See FIGURE 2.
• Proceed to to STEP 3.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
15
4
5
FIGURE 3
STEP 3:
• Insert one 3/4 X 4” SHAFT (15) thru pre-installed FLANGE BEARINGS in the SECONDARM (5) as shown in FIGURE 3.
• Insert one 3/4 X 4” SHAFT (15) thru pre-installed FLANGE BEARINGS in the MAINARM (4) as shown in FIGURE 3.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6
13
5
4
12 1/2 X 4-3/4”
FIGURE 4
STEP 4:
• SECURELY assemble the FOOTPLATE (6) to the SECONDARM (5) and the MAINARM (4) using two 1/2 X 4-3/4” BOLTS (12) and two
1/2” LOCK NUTS (13). See FIGURE 4.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3/8 X 3” 9
1
3
10
11
FIGURE 5
STEP 5:
• SECURELY assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 3” BOLTS (9), four 3/8” FLATWASHERS (10) and two 3/
8” LOCK NUTS (11) as shown in FIGURE 5.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
9
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
14
17
1
FIGURE 6
STEP 6:
• Securely assemble one PLUNGER PIN (14) to the FRAME (1) as shown. (NOTE: Screw PLUNGER PIN (14) in all the way)
• Securely assemble one M4 SET SCREW (17) to the plunger pin barrel on the FRAME (1) then back off 1/4 turn so PLUNGER PIN (14)
rotates freely until the threads come in contact with the M4 SET SCREW (17)
• CAREFULLEY slide the SEATADJUST (2) into the FRAME (1) as shown. The SEAT can be adjusted by turning the SPRING PIN
KNOB (14) clockwise and pulling. The SEAT can be secured in place by releasing the pin into an adjustment hole and turning
clockwise until tight.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
8
2
10
9 3/8 X 3”
FIGURE 7
STEP 7:
• SECURELYassemble one PAD (8) to the SEATADJUST (2) using two 3/8 X 3” BOLTS (9) and two 3/8” FLATWASHERS (10) as
shown in FIGURE 7.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
8
1
10
3/8 X 3” 9
7
FIGURE 8
STEP 8:
• SECURELYassemble one PAD (8) to the FRAME (1) using two 3/8 X 3” BOLTS (9) and two 3/8” FLATWASHERS (10) as shown in
FIGURE8.
•
Refer to the LEG PRESS ADAPTOR assembly instructions to attach the LP5 LEG PRESS to the home gym. The PULLEY
BRACKET (7) will be attached at that time.
Thank you for purchasing the Parabody LP5 LEG PRESS. If unsure of proper use of equipment, call your
local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
SERIALNUMBER LOCATION
Thank you for purchasing the ParaBody LP5 Leg Press.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: 763.323.4500 Fax: 763.323.4797
800.328.9714 (Toll-free within the U.S. and Canada)
INTERNATIONALOFFICES
Life FitnessAtlantic BV
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
Life Fitness Benelux N.V.
Bijdorpplein 25-31
85716 Unterschleissheim
Germany
2992 LB Barendrecht
The Netherlands
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Italia S.R.L.
Via Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|