Model No.
FV-05-11VKS1
FV-05-11VK1
FV-11-15VK1
Contents
2-3
GENERAL SAFETY INFORMATION
PLEASE READ PRIOR TO INSTALLING THIS FAN
DESCRIPTION
4
4
4
UNPACKING
5
SUPPLIED ACCESSORIES
5
DIMENSIONS
5
WIRING DIAGRAM
FEATURE
6
FV-05-11VKS1 FV-05-11VK1
INDICATION (PLUG ‘N PLAY FUNCTION DEVICES)
MOTION (PLUG ‘N PLAY FUNCTION DEVICES)
INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES)
INSTALLATION (NEW CONSTRUCTION)
INSTALLATION (RETROFIT)
MAINTENANCE (CLEANING)
6-7
7
8
8-10
10
11
PRACTICAL GUIDE TO INSTALLATION
SPECIFICATIONS
BACK COVER
BACK COVER
BACK COVER
PRODUCT SERVICE
FV-11-15VK1
Thank you for purchasing this Panasonic product.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Canada only: Not to be installed in a ceiling thermally insulated to a value greater than R40.
Do not disassemble the unit for reconstruction. It may cause fire or electric shock.
When this product is no longer being operated, please remove the product to prevent the
possibility of falling.
Ceiling joist must be subjected to static load more than five times the weight of the product.
Do not install with a method which is not approved in the instructions.
Do not use this fan with any solid-state speed control device. Solid state controls may cause
harmonic distortion which can cause motor humming noise.
This product must be properly grounded.
CAUTION
Do not install this ventilating fan where interior room temperature may
exceed 104°F(40°C).
Make sure that the electric service supply voltage is AC 120V, 60Hz.
Follow all local electrical and safety codes, as well as the National
Electrical Code (NEC) and the Occupation Safety and Health Act (OSHA).
Always disconnect the power source before working on or near the fan,
motor or junction box.
Protect the supply wiring from sharp edges, oil, grease, hot surfaces,
chemicals or other objects.
Adaptor
Do not kink the supply wiring.
Provide make up air for proper ventilation.
For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
(Cooking area)
Do not install the unit where ducts are configured as shown
Do not install above or
in Fig.A.
inside this area
Not for use in cooking area. (Fig.B)
The special-purpose or dedicated parts, such as mounting
fixtures, must be used if such parts are provided.
Floor
Cooking
equipment
Fig. B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE READ PRIOR TO INSTALLING THIS FAN
Spot and Continuous Ventilation: These fans are designed to run continuously ensuring a healthy
environment at low CFM levels 24 hours a day. By utilizing the optional CustomVent Multi-Speed
module the fans are built to run continuously at a pre-set lower level (FV-05-11VKS1 and FV-05-11VK1:
0, 30, 40, 50, 60, 70, 80, 90, 100 CFM; FV-11-15VK1: 0, 50, 60, 70, 80, 90, 100, 110, 120 CFM). The
setting is dependent on the size of the house and the individual wishes of the homeowner. It is crucial
that the installer pre-set the lower setting during the installation. Please refer to the chart below
and the switch indication on page 6.
CustomVent Multi-Speed module (Lower Setting). ASHRAE 62.2-2010
(sq.feet)
Two Bedrooms Three Bedrooms Four Bedrooms Five Bedrooms
33
38
43
48
53
58
63
68
73
78
83
88
93
40
45
50
55
60
65
70
75
80
85
90
95
100
<1,000
1,500
2,000
2,500
3,000
3,500
4,000
4,500
5,000
5,500
6,000
6,500
7,000
48
53
58
63
68
73
78
83
88
93
98
103
108
55
60
65
70
75
80
85
90
95
100
105
110
These fans are also built to take care of the homeowner’s spot ventilation needs when the room is
occupied. The basic fan models allow a choice of three speeds. When fans are equipped with the optional
Multi-Speed module, these models kick up to a maximum level of 150 CFM for the FV-11-15VK1 and 110
CFM for the FV-05-11VKS1 and FV-05-11VK1 either when the switch is turned on or activated by the
optional Condensation Sensor module or the optional Motion Sensor module.
A High/Low Delay Timer, located inside the fan unit, is utilized to return the fan back to the pre-set
Continuous ventilation mode. The installer needs to consult with the homeowner for the desired
setting on the timer (0 - 60 minutes) and make the adjustments during the installation.
DESCRIPTION
These products are listed by UL under UL file No. E78414.
These products use a sirocco fan driven by a DC motor powered by an integral transformer. The motor is
designed to have long operating life, high dynamic response, higher speed ranges with saving energy.
The grille covering the fan body is a spring-loaded, quick remove type. A damper for preventing air counter
flow is provided. The blower uses a high-capacity sirocco fan developed to reduce the noise level.
UNPACKING
Unpack and carefully remove the unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPPLIED ACCESSORIES
Quantity
Quantity
1
Part name
Appearance
Part name
Appearance
Warranty
sheet
Grille
1
Flex-Z FastTM
bracket
Tapping screw
(ST4.2X20)
1
2
4
4
Installation
instructions
Self-drilling
screw
DIMENSIONS
Unit: inches (mm)
FV-11-15VK1
1 (26)
7/8 (22.5)
4
5/8 (116)
10
FV-05-11VK1
FV-11-15VK1
6
3/8 (163)
7
3/8 (190)
12
11
11
FV-11-15VK1
FV-05-11VKS1
No.
1
No.
7
Part name
Part name
Connector cover
Base PCB box
13 (330)
Blade
Grille
2
8
Motion sensor location
(FV-MSVK1 not included)
9
Pick-A-Flow switch
3
10
11
4
5
Junction box
Adaptor
Fan body
Damper
Multi-Speed module
(FV-05-11VKS1 only,
Flex-Z FastTM bracket
12
6
3 7/8 (100)
10 1/4 (260)
3 7/8 (100)
other models not included)
WIRING DIAGRAM
Junction box
Fan body
DC-Motor
Switch for power
(114°C Fuse)
Live
Black
(Power supply)
AC120V 60Hz
Thermally
protected
Neutral
White
Multi-Speed module
(FV-05-11VKS1
Hi/Low switch: When plug in
Multi-Speed module;
On/Off switch: When plug in
other Plug ‘N Play modules.
only, other models
not included)
Red
Red
Plug ‘N Play module slot
(Non-powered control wires)
Plug ‘N Play module slot
Green
Earth ground
Green
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURE
[For models of: FV-05-11VKS1, FV-05-11VK1, FV-11-15VK1.]
The WhisperGreen Select Line of ventilation fans employs innovative, state-of-the-art technologies that
provide a number of customizable unique features that lead to improved indoor air quality. Please
read the installation manual first in order to realize the benefits of this customizable, modular fan.
Optimum Ventilation Performance:
Duct length, elbows and other factors increase static pressure which can hinder the performance of most
ventilation fans. This fan utilizes SmartFlow microchip technology that monitors the static pressure in the
system and speeds up or slows down the rpm of the fan depending upon the amount of resistance within
the ducts. This feature allows the fan to perform as rated and avoid potential installation issues.
Outstanding Energy Savings:
The WhisperGreen Select Line of fans are built using DC motor technology. The DC motor is 30% - 70%
more energy efficient than the minimum ENERGY STAR requirements.
Pick-A-Flow Feature
All the WhisperGreen Select base models of fans come with Pick-A-Flow
speed options. The Pick-A-Flow switch on the face of all WhisperGreen
Select fans allows the option to choose 50 – 80 – 110 CFM for the
FV-05-11VK1, FV-05-11VKS1 or 110 – 130 – 150 CFM for the
FV-11-15VK1. These fans can run continuously or intermittently,
depending upon the needs of the owner.
Air volume type (CFM)
Factory setting
(
)
AIR VOLUME CFM
05-11 50
Pick-A-Flow
switch
80 110
FV-05-11VKS1
FV-05-11VK1
MODEL
50
80
110
80 CFM
11-15
FV-11-15VK1
110 130 150
130 CFM
MODEL110130150
INDICATION (PLUG ‘N PLAY FUNCTION DEVICES)
PLUG ‘N PLAY Modular Component Accessories
Sold Separately, Not Included With Base Model Fan
FV-VS15VK1 Multi-Speed module allows the fan to run continuously
at lower speeds to maintain ventilation standards to meet Indoor
Air Quality and then boost up to high speed to meet intermittent
needs for ‘Spot’ or ‘Point Source’ exhaust needs. The FV-VS15VK1
Modular Component will operate for both the FV-05-11VK1 and the
FV-11-15VK1 matching the appropriate Multi-Speed setting shown
below. The FV-05-11VKS1 comes with the FV-VS15VK1 Multi-Speed
module. It is not necessary to purchase this component.
Note the options on the face of the FV-VS15VK1 Multi-Speed module
to choose appropriate levels of airflow (CFM) and time delay before
returning back to low speed (TIME). Choosing the Pick-A-Flow setting
automatically adjusts the Multi-Speed setting accordingly. As an
example, if the Pick-A-Flow Multi-speed setting is 80 CFM, the
Multi-Speed settings adjust automatically to be 0, 30, 40, 50, 60 or 70
CFM at the lower speeds. The fan will ‘boost’ to the 80 CFM speed as
the high speed setting. Selecting a particular TIME option will cause
the fan to run for the selected amount of time before returning to
the lower speed setting chosen on the CFM dial.
Note that there is ONLY ONE
Plug ‘N Play slot to insert the
Multi-Speed module within the
base model fan. There are TWO
interchangeable Plug ‘N Play
slots to insert the Condensation
Sensor module, Motion Sensor
module or Nite-GloTM LED Night
Light module within the base
model fan.
Multi-Speed Air volume (CFM)
Pick-A-Flow (CFM)
50
80
110
110
130
150
0
0
0
0
0
0
30
30
30
50
50
50
40
40
40
60
60
60
40
50
50
70
70
70
40
60
60
80
80
80
40
70
70
40
70
80
40
70
90 100
40
70
FV-05-11VKS1,
FV-05-11VK1
(plug-in FV-VS15VK1)
90 100 100 100
90 100 110 110
90 100 110 120
FV-11-15VK1
(plug-in FV-VS15VK1)
Delay Time (min)
45
Factory setting: 20 minutes.
Delay Time position “0“ : Manual wall switch control is 0 minute;
without manual wall switch control is 0.5 minute.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICATION (PLUG ‘N PLAY FUNCTION DEVICES) CONTINUED
PLUG ‘N PLAY Modular Component Accessories
Sold Separately, Not Included With Base Model Fan
FV-CSVK1 Condensation Sensor module turns the base fan on or
boosts to higher speed when humidity is detected when used in
combination with the FV-VS15VK1. The Condensation Sensor works
based on calculations from the Psychrometric Chart, or combination
of Relative Humidity (RH) and Temperature. This allows the fan to
anticipate the formation of condensation and automatically turn on
when needed to expel humid air. The Condensation Sensor is pre-set
to run for 20 minutes; it will then check the RH and Temperature to
detect if the fan needs to run for another 20 minutes cycle.
FV-MSVK1 Motion Sensor module turns the base fan on or boosts
to higher speed when motion is detected when using in combination
with the FV-VS15VK1. The Motion Sensor is pre-set to run for 20
minutes; it will then re-check for movement; if detected the fan will
run for another 20 minutes cycle. The Motion Sensor detects within
the range shown below.
The distance that motion
can be detected is limited
to 10 feet (3m). The field
of view of the sensor is 90°.
(Room temperature is 25 C).
FV-NLVK1 Nite-GloTM LED Night Light module automatically turns on
when ambient light levels are met. Turning the dial on the Modular
Nite-Glo Component to ‘DARK’ is ideal if the fan is in an isolated room
with little ambient light from nearby rooms. Turning the dial to
‘BRIGHT’ is ideal if there is light spill from nearby rooms. (Note that it is
necessary to connect wall switch when only plug in FV-NLVK1, fan can
operate on high speed with wall switch control, fan can also operate
on low speed when used in combination with the FV-VS15VK1.)
MOTION (PLUG ‘N PLAY FUNCTION DEVICES)
PLUG ‘N PLAY Modular
Components used in
Combinations
PLUG ‘N PLAY Modular Component Accessories
Sold Separately, Not Included With Base Model Fan
FV-CSVK1 + FV-MSVK1
Turns the fan on for 20 minutes when either
motion or excess humidity is detected.
FV-CSVK1 + FV-VS15VK1
Cycles the fan to high speed from low speed
for the amount of time selected on the Control
Dial based upon detection of excess humidity.
FV-MSVK1 + FV-VS15VK1
Cycles the fan to high speed from low speed
for the amount of time selected on the Control
Dial based upon motion within the room.
Fan
Time delay
operation
Motion
Human
active
operation
FV-CSVK1 only
Fan
ON/OFF
20 minutes
time delay
When motion or
excess humidity is
detected, fan runs the delay time has
at high speed. passed.
Remains running
at high speed until
FV-MSVK1 only
Fan
active
At low
speed
Depend on
FV-VS15VK1 Time
delay setting
FV-CSVK1 + FV-VS15VK1
FV-MSVK1 + FV-VS15VK1
Fan
Hi/Low speed
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES)
You can purchase the specified Plug ‘N Play devices that are explained on page 6-7 and install them in positions
2
3
,
and
. Position
can only be used with Multi-Speed module (model FV-05-11VKS1 already have
and can be used for any of the other optional control modules.
this control installed), position
2
3
1. Remove the connector cover from position
, 2 or 3 .
2. Plug in the specified devices to Base PCB box and fix to the slot, till hear the sound installed in place.
Connector
cover
Base PCB box
Slot
2
2
3
3
Clasp
Squeeze tabs on the Clasp to
remove. Squeeze, insert and
release the tabs on Clasp to replace.
INSTALLATION (NEW CONSTRUCTION)
The fan position between joists from 16" to 24"
on center can be adjusted flexibly.
Adaptor
Machine screw
(M4X6)
CAUTION
Please wear gloves during the installation
work as follow.
Fig.1
Fan body
1. Disconnet plug connector from receptacle and
remove adaptor from fan body by removing the
machine screw (M4X6) before installation. (Fig.1)
Joist
IMPORTANT:
Remove the tape from damper and adaptor
before installation. As shown below:
Bend down
4 tabs
Adaptor
Damper
2 Tapping screws
(ST4.2X20)
Fig.2
Tape
Joist
2. Bend down 4 tabs for positioning, install the
Flex-Z FastTM bracket to joists by using 2 tapping
screws(ST4.2X20) (Please prepare the screws and
put on Flex-Z FastTM bracket before Flex-Z FastTM
bracket is installed on joist). (Fig.2)
3. Adjust the length of Flex-Z FastTM bracket as the
spacing between joists, and install to joists by
using 2 tapping screws (ST4.2X20). (Fig.3)
4. Remove junction box cover and secure conduit
or stress relief to junction box knock-out hole.
(Fig.4)
2 Tapping screws
(ST4.2X20)
Fig.3
Circular duct
Mastic or
approved
foil tape
Conduit
5. Install a circular duct and secure it with clamps,
or ties and seal it with mastic or approved foil tape.
4 inch 6 inch circular duct is needed to connect to
relevant part of common adaptor. (Fig.4)
6. Install the adaptor to Flex-Z FastTM bracket by
using 2 self-drilling screws. (Fig.4)
Knock-out
hole
Junction box
cover
2 Self-drilling screws
Fig.4
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (NEW CONSTRUCTION) CONTINUED
7. Refer to wiring diagram on page 5.
Follow all the local electrical safety codes as well
as the National Electrical Code (NEC).
Using UL approved wire nuts, connect house
power wires to ventilating fan wires. (Fig.5)
FV-05-11VKS1
FV-05-11VK1
FV-11-15VK1
Conduit
Earth ground
to green
Wire nut
Junction
box
Netural to white
CAUTION
Two red wires
(Connect to a general
manual wall switch)
Mount junction box cover carefully so that
lead wires are not pinched.
Live to black
Fig.5
8. Insert fan body and slide into adapter assy with
some strength, untill the flange overlaps the
Flex-Z FastTM bracket. Secure the fan body to
Flex-Z FastTM bracket by using 2 self-drilling screws,
plug connector to receptacle and secure the fan
body to adaptor by using machine screw (M4X6).
(Fig.6)
Joist
CAUTION
Plug connector
Receptacle
Secure machine screw (M4X6) to the suitable
hole and not touch the Flex-Z FastTM bracket.
Please fix the screw carefully to avoid screw
slip teeth.
Machine
screw
(M4X6)
2 Self-drilling
screws
9. Finish ceiling work. Ceiling hole should be aligned
with the inside edge of the flange. (Fig.7)
Fig.6
10. Remove the tapes from louver and springs
before installation. (Fig.8)
Ceiling
Unit: inches (mm)
(270)
10 1/2
10 1/2
IMPORTANT:
(270)
Replace the sensor cover before the installation
(only for plug-in Motion sensor modular FV-MSVK1).
As shown below:
Keep on pressing the clasps when removing the ornamental cover.
Gloves
After finishing the ceiling job, fill gap between flange
and ceillng with caulk or other sealant to prevent air
leakage
Fig.7
Tapes
Ornamental
cover
Insert the sensor cover (attachment for FV-MSVK1) into slot.
Sensor
cover
Fig.8
Clasp
Ceiling
11. Insert the grille mounting spring on the wiring
side into the slot. (Fig.9)
12. Plug in the specified devices as your choice
(refer to installation on page 8). Insert the
motion sensor (FV-MSVK1 only) or LED night
light (FV-NLVK1 only) into slot of the grille.
Fix the lead wire into the clasp (Fig.9).
Motion sensor
(FV-MSVK1 only)
LED night light
(FV-NLVK1 only)
Fig.9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (NEW CONSTRUCTION) CONTINUED
13. Adjust Pick-A-Flow switch; if used, adjust the
FV-VS15VK1 Multi-Speed module. (Fig.10)
Refer to indication on page 6.
Ceiling
Grille
14. Insert the other mounting spring into the slot as
shown and mount grille to fan body. (Fig.11)
Fig.10
CAUTION
Mount grille carefully so that lead wire is
Ceiling
not pinched.
Mounting
spring
Gloves
Fig.11
Grille
INSTALLATION (RETROFIT)
Unit: inches (mm)
Joist
Conduit
Circular duct
WARNING
Disconnect power source before working
on unit.
4 Tapping
screws (ST4.2x20)
1. Remove the existing fan and cut ceiling openning.
Secure the Flex-Z FastTM bracket to joists by using 4
tapping screws (ST4.2x20) (Please prepare the
screws and put on Flex-Z FastTM bracket before
Flex-Z FastTM bracket is installed on joist).
(275)
10 7/8
Fig.12
Ceiling (already existed)
Conduit
Existing ductwork and wiring left in place. (Fig.12)
Circular duct
Mastic or
approved
foil tape
2. Follow the step 1, 4, 5 on page 8 and step 7 on
page 9. (Before connect the circular duct to the
adaptor, should pull down the circular duct from
the ceiling)
Joist
Knock-out
hole
3. Install the adaptor to Flex-Z FastTM bracket by
using 2 self-drilling screws. (Fig.13)
Junction box
cover
2 Self-drilling screws
Ceiling
Fig.13
4. Secure the fan body to Flex-Z FastTM bracket by
using 2 self-drilling screws, plug connector to
receptacle and secure the fan body to adaptor
by using machine screw (M4X6). (Fig.14)
Joist
CAUTION
Secure machine screw (M4X6) to the suitable
hole and not touch the Flex-Z FastTM bracket.
Please fix the screw carefully to avoid screw
slip teeth.
Ceiling
Flange
Machine screw (M4X6)
2 Self-drilling screws (Fix the
flange and Flex-Z Fast bracket through the ceiling)
TM
5. Follow the step 10 to 14 on page 9 to 10.
Fig.14
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting spring
Gloves
WARNING
Disconnect power source before working
on unit.
Grille
Slot
Fig.15
CAUTION
Routine maintenance must be done
every year. Please wear gloves during
the cleaning work.
Clasp
Ceiling
Never use gasoline, benzene, thinner or
any other such chemicals for cleaning the
ventilating fan.
Motion sensor
(FV-MSVK1 only)
LED night light
Do not immerse motor in water when
cleaning. Do not soak resin parts in water
over 140°F (60°C).
(FV-NLVK1 only)
Fig.16
1. Remove grille by pulling down one mounting
spring (Fig.15), then pull down the other. (For
models plug-in FV-MSVK1 or FV-NLVK1: Pull
down the mounting spring that without lead
wire passed side, and remove motion sensor or
LED night light as shown in Fig.16) (Squeeze
mounting spring and pull down carefully)
Gloves
Fig.17
2. Clean grille. (Don’t put into hot water. Use
non-abrasive kitchen detergent, wipe dry with
clean cloth) (Fig.17)
Ceiling
3. The grille should be dry after cleaning.
Vacuum
cleaner
4. Remove dust and dirt from fan body using a
vacuum cleaner. (Fig.18)
Fig.18
5. Using a cloth dampened with kitchen detergent,
remove any dirt from fan body. Wipe dry with
clean cloth. (Fig.19)
Ceiling
6. Reinstall grille.
Gloves
Fig.19
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PRACTICAL GUIDE TO INSTALLATION
Properly insulate the area around the fan to
minimize building heat loss and gain. (Fig.20)
Loose fill or batt insulation can be placed
directly over the fan housing in the attic.
Our fans and fan/light combination units do
not create excessive heat that is a common
problem with recessed light fixtures or some
competitor’s fan/light combination. Our
efficient, cool-running motors and our LED
lighting unit do not create enough ambient
heat to be subjected to these limitations.
4 inches or 6 inches roof jack, wall cap,
or soffit vent with backdraft damper
Mechanically connect duct to termination
and seal with mastic or approved foil
faced tape
2-3 ft straight run before elbow
ln attic installation,
caulk box to drywall
Short piece of flexible duct helps
alignment and absorbs sound.
lnsulation
Clamps plus mastic or approved
foil faced tape at all flex joints
Foil tape tightly covers all metal
duct joints (glue PVC joints)
Fig.20
SPECIFICATIONS
Specifications for Base Model fans
Duct
Air volume
Noise
Air
direction
Voltage Frequency
Speed
(rpm)
Power
(W)
Weight
Ib.
diameter at 0.1"WG
(inches)
Model No.
(V)
(Hz)
(sones)
(CFM)
<0.3
<0.3
<0.3
<0.3
<0.3
50
80
110
110
130
150
740
795
915
620
630
660
3.5
5.5
9.5
7.0
10.0
FV-05-11VKS1
FV-05-11VK1
Exhaust
Exhaust
4 or 6
10.6(4.8)
10.6(4.8)
FV-11-15VK1
13.0
<0.3
HVI Certified performance based on HVI Procedures 915, 916, and 920.
Specifications for Multi Speed fans
Duct
Air volume
Air
direction
Voltage Frequency
(V) (Hz)
Noise
(sones)
Speed
(rpm)
Power
(W)
Weight
Ib.
diameter at 0.1"WG
(inches)
Model No.
(CFM)
100
90
80
70
60
50
40
30
0
120
110
100
90
80
70
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
8.0
6.5
5.5
4.3
3.6
3.5
2.7
2.4
870
835
795
760
745
740
FV-05-11VKS1,
FV-05-11VK1
(Plug-in
FV-VS15VK1)
Exhaust
Exhaust
10.6(4.8)
10.6(4.8)
730
725
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
<0.3
7.4
7.0
5.6
4.9
4.4
3.8
3.6
3.1
625
620
615
610
605
600
FV-11-15VK1
(Plug-in
FV-VS15VK1)
60
50
595
590
0
Warning Concerning Removal of Covers. The unit should be serviced by qualified technicians only.
Your product is designed and manufactured to ensure a minimum of maintenance. Should your unit
require service or parts, call Panasonic Call Center at 1-866-292-7299 (USA) or 1-800-669-5165 (Canada).
Two Riverfront Plaza, Newark, NJ 07102
Panasonic corporation 2014
X0114-2024 15VK10420B
Download from Www.Somanuals.com. All Manuals Search And Download.
|