Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 - Disclaimer! Read this throroughly.
Before installing the KeyMaster which is able to make your DVD
player codefree, you should read through these warnings
thoroughly:
v We are not responsible for any illegal use of the KeyMaster.
v We offer no warranty on your DVD-player.
v The installation of the KeyMaster is at your own risk.
v By installing the KeyMaster you may invalidate the warranty of
your DVD-player.
v If the manufacture of the DVD-player makes changes we can’t
the guaranty the functionality of the KeyMaster.
v The KeyMaster is to be installed inside your DVD-player and it is
therefore necessary to be familiar with soldering, otherwise you
should get a service center to do the installation for you.
v Remember to disconnect the DVD-player from the mains, before
opening the DVD-player.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 - Removal of the top cover.
It is necessary to remove the frontcover of the tray. First, open the
tray by pressing "OPEN" on the player or the remote control. Then,
pull the bottom of the frontcover of the tray forward and simultaneli-
ty carefully pull it upwards. Shown on fig. 1.
Fig. 1
Note: The picture shows a Panasonic A160.
Remember to disconnect the player from the mains before proce-
ding. Remove the seven screws which holds the topcover, two in
each side and three on the back of the player as shown on fig. 2.
Fig. 2
Note: The picture shows a Panasonic DVD-RV60.
Download from Www.Somanuals.com. All Manuals Search And Download.
continued...
To remove the mechanism, use the following procedure:
Ÿ
Ÿ
Disconnect the cables connected to the frontpanel of the player.
Remove the frontpanel by loosening the seven snap-locks.
Please be aware that the bottom chassis can have very sharp
edges.
Ÿ
Ÿ
Remove the four screws which holds the mechanism.
Then remove the mechanism by pulling the backside of the
mechanism upwards.
Note: The mechanism is sensitive towards static electricity and
should be handled carefully.
Fig. 3
Note: The picture shows a Panasonic DVD-RV60.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 - Installing the KeyMaster.
When the mechanism is removed it is possible to install the Key-
Master. fig. 4.
Fig. 4
Seven wires have to be soldered onto the MPEG board (which are
attached to the mechanism). All seven wires have to be soldered
onto the bottomside of the MPEG board. Remember to adjust the
ends of the wires so they will fit onto the soldering pads.
Solder the seven wires onto the board as shown on fig. 4-5-6.
Do not change or remove any components.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 - Continued.
Fig. 5
à Connect the RED wire to the testpoint TP6209.
à Connect the BLACK wire to the testpoint TP6201.
à Connect the BROWN wire to the testpoint TP6204 or pin 2,
IC6303.
à Connect the WHITE wire to the testpoint TP6202 or pin 6,
IC6303.
Fig. 6
à Connect the PURPLE wire on pin 1, IC6303.
à Connect the GREY wire on pin 5, IC6303.
à Connect the BLUE wire on pin 4, IC6301.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 - Installation in the Panasonic SA-PM08.
In the Panasonic SA-PM08 the installation has to done as follows:
Fig. 7
à Connect the RED wire to C6501 (+).
à Connect the BLACK wire to the C6501 (-).
à Connect the BROWN wire to the shown testpoint TP6204 or
pin 2, IC6303.
à Connect the WHITE wire to the shown testpoint TP6202 or pin
6, IC6303.
à Connect the GREY wire to the testpoint TP6202 or pin 5,
IC6303.
Fig. 8
à Connect the PURPLE wire on pin 1, IC6303.
à Connect the BLUE wire on pin 4, IC6301.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 - Securing KeyMaster.
Before fastening the KeyMaster the wires have to be fixed with a
cable tie. Use the cable tie as shown on fig. 9. Fix the wires so they
are not located underneath the chassis of the mechanism.
Fig. 9
Note: the picture shows a Panasonic DVD-RV60.
Secure the KeyMaster onto the mechanism chassis as shown on
fig. 9. Remove the protection film from the double sided tape and
press the KeyMaster thoroughly towards the chassis.
In Panasonic SA-PM08 the KeyMasteren has to be sercured as
shown in Fig. 10.
Fig. 10
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 - Assembling the player.
Assembling the player is done using the following procedure:
Ê Use the four screws to attach the mechanism.
Ë Press the cables from the frontpanel into their sockets.
Ì Attach the front of the player again. Then ensure all snap-
locks.
• Put the topcover back on and secure it.
• Refit the frontpanel of the tray.
3.5 - Finishing up the installation.
After turning the player on and off the KeyMaster is ready for use.
The player and the KeyMaster is now ready for use. For details
about programming the KeyMaster look in the operating instructi-
ons.
Remember to test the player in both region 1 & 2.
Enjoy our product, the KeyMaster!
Download from Www.Somanuals.com. All Manuals Search And Download.
|