TG1311_1312_1313BX(e).book Page 1 Tuesday, September 2, 2008 10:36 AM
Operating Instructions
Digital Cordless Phone
Model No. KX-TG1311BX
KX-TG1312BX
KX-TG1313BX
Table of Contents
Introduction ......................................................... 2
Preparation .......................................................... 4
Making/Answering Calls..................................... 9
Phonebook......................................................... 11
Useful Telephone Settings ............................... 12
Caller ID Service................................................ 16
Multi-unit Operation .......................................... 17
Useful Information............................................. 18
Model shown is KX-TG1311.
This unit is compatible with Caller ID. You must subscribe to the
appropriate service offered by your service provider/telephone
company.
Charge the batteries for about 7 hours before initial use.
Please read these operating instructions before using the unit and
save them for future reference.
PNQX1123ZA DC0908DQ0
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 3 Tuesday, September 2, 2008 10:36 AM
Introduction
L This product should be kept away from heat sources such as radiators,
cookers, etc. It should also not be placed in rooms where the
temperature is less than 5 °C or greater than 40 °C.
Important information
Warning:
General
L To prevent the risk of electrical shock, do not expose this product to rain
or any other type of moisture.
L Use only the AC adaptor supplied with this product, noted on page 2.
L Do not connect the AC adaptor to any AC outlet other than a standard
220–240 V AC outlet.
L Unplug this product from power outlets if it emits smoke, an abnormal
smell, or makes unusual noise. These conditions can cause fire or
electric shock. Confirm that smoke has stopped emitting and contact an
authorised service centre.
− the portable handset battery(ies) need recharging or have failed.
− there is a power failure.
− the key lock feature is turned on.
− the call bar feature is turned on (only phone numbers stored in the unit
as emergency numbers can be called).
L Do not spill liquids (detergents, cleansers, etc.) onto the telephone line
cord plug, or allow it to become wet at all. This may cause a fire. If the
telephone line cord plug becomes wet, immediately pull it from the
telephone wall jack, and do not use.
L Do not place or use this product near automatically controlled devices
such as automatic doors and fire alarms. Radio waves emitted from this
product may cause such devices to malfunction resulting in an accident.
L Regularly remove any dust, etc. from the AC adaptor/power plug by
pulling it from the power outlet, then wiping with a dry cloth. Accumulated
dust may cause an insulation defect from moisture, etc. resulting in a fire.
L Do not damage the power cord/plug. This may cause a short circuit,
electric shock, and/or fire.
L Do not open the base unit, charger, or handset other than to replace the
battery(ies).
L Consult the manufacturer of any personal medical devices, such as
pacemakers or hearing aids, to determine if they are adequately
shielded from external RF (radio frequency) energy. (The product
operates in the frequency range of 1.88 GHz to 1.90 GHz, and the RF
transmission power is 250 mW (max.).) Do not use the product in health
care facilities if any regulations posted in the area instruct you not to do
so. Hospitals or health care facilities may be using equipment that could
be sensitive to external RF energy.
L Do not touch the plug with wet hands.
L The AC adaptor is used as the main disconnect device. Ensure that the
AC outlet is installed near the product and is easily accessible.
L Care should be taken that objects do not fall onto, and liquids are not
spilled into, the product. Do not subject this product to excessive smoke,
dust, mechanical vibration or shock.
Battery caution
L Only the supplied handset can be used with the base unit. No other
handsets can be registered or used.
L We recommend using the battery(ies) noted on page 2. USE ONLY
rechargeable Ni-MH batteries AAA (R03) size.
L Do not mix old and new batteries.
L Do not dispose of the battery(ies) in a fire, as they may explode. Check
with local waste management codes for special disposal instructions.
Environment
L Do not use this product near water.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 4 Tuesday, September 2, 2008 10:36 AM
Preparation
Pri
L Do not open or mutilate the battery(ies). Released electrolyte from the
battery(ies) is corrosive and may cause burns or injury to the eyes or
skin. The electrolyte may be toxic if swallowed.
Connections
L Exercise care when handling the battery(ies). Do not allow conductive
materials such as rings, bracelets or keys to touch the battery(ies),
otherwise a short circuit may cause the battery(ies) and/or the
conductive material to overheat and cause burns.
Base unit
The base unit can be mounted on the wall, if required.
L Use only the supplied Panasonic AC adaptor PQLV207BX.
L Use only the supplied telephone line cord. Using another telephone line
cord may not allow the unit to work properly.
L Charge the battery(ies) provided with or identified for use with this
product only in accordance with the instructions and limitations specified
in this manual.
L Only use a compatible base unit (or charger) to charge the battery(ies).
Do not tamper with the base unit (or charger). Failure to follow these
instructions may cause the battery(ies) to swell or explode.
30 mm
Notice for product disposal, transfer, or return
L This product can store your private/confidential information. To protect
your privacy/confidentiality, we recommend that you erase the
information such as phonebook or caller list entries from the memory
before you dispose of, transfer, or return the product.
Screws
(Not supplied)
Hooks
(220-240 V AC, 50/60 Hz)
Information on Disposal in other Countries outside the European
Union
To telephone line
These symbols are only valid in the European Union. If you wish to discard
these items, please contact your local authorities or dealer and ask for the
correct method of disposal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 5 Tuesday, September 2, 2008 10:36 AM
Preparation
Charger
If you subscribe to a DSL/ADSL service
L Please attach a DSL/ADSL filter (contact your DSL/ADSL provider) to
the telephone line between the base unit and the telephone line jack in
the event of the following:
Available for:
KX-TG1312/KX-TG1313
The charger can be mounted on the wall, if required.
− noise is heard during conversations.
− Caller ID features do not function properly.
L Use only the supplied Panasonic AC adaptor PQLV209BX.
25.2 mm
Hooks
(220-240 V AC, 50/60 Hz)
To telephone line
DSL/ADSL filter
Screws
(Not supplied)
Location
Note:
For maximum distance and noise-free operation, place your base unit:
− away from electrical appliances such as TVs, radios, personal
computers, or other phones.
L Never install telephone wiring during a lightning storm.
L Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the
weight of the adaptor may cause it to become disconnected.
− in a convenient, high, and central location.
During a power failure
The unit will not work during a power failure. We recommend connecting a
corded-type telephone (without AC adaptor) to the same telephone line or
to the same telephone line jack using a T-adaptor.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 6 Tuesday, September 2, 2008 10:36 AM
Preparation
Battery installation
Battery charge
Important:
Place the handset on the base unit or charger for about 7 hours before
initial use.
L Use the supplied rechargeable batteries (Part No. HHR-55AAAB).
L When installing the batteries:
− Wipe the battery ends (S, T) with a dry cloth.
− Avoid touching the battery ends (S, T) or the unit contacts.
− Confirm correct polarities (S, T).
L If the handset does not automatically turn on after installing batteries,
press {ih} for about 1 second, or place the handset on the base unit
or charger.
Battery level
Battery icon
5
Battery level
High
L When flashing: Fully charged.
6
Medium
Low
Insert the batteries negative (T) end first. Close the handset cover.
7
L When flashing: Needs charging.
Panasonic Ni-MH battery performance (supplied batteries)
Operation
Operating time
17 hours max.
150 hours max.
In continuous use
Not in use (standby)
Note:
Turning the power on/off
L It is normal for batteries not to reach full capacity at the initial charge.
Maximum battery performance is reached after a few complete cycles of
charge/discharge (use).
Power on
L Actual battery performance depends on a combination of how often the
handset is in use and how often it is not in use (standby).
Press {ih} for about 1 second.
L Even after the handset is fully charged, the handset can be left on the
base unit or charger without any ill effect on the batteries.
Power off
Press {ih} for about 2 seconds.
L The battery level may not be displayed correctly after you replace the
batteries. In this case, place the handset on the base unit or charger and
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 7 Tuesday, September 2, 2008 10:36 AM
Preparation
let it charge for at least 7 hours.
Base unit
Controls
A Charge contacts
{x} (Locator)
A
B
Handset
A Receiver
B
B Display
C
D
{k} (Phonebook)
{C} (Talk)
N
E Navigator
({e}/{v}/{>}/{<})
? (Volume: {e}/{v})
{R} (Redial/Pause)
{R} (Recall/Flash)
A
B
Display
F
G
Handset display items
H Microphone
C
D
E
F
I
J
K
L
{j/OK} (Menu/OK)
{ih} (Off/Power)
{C} (Clear)
{INT}
KX-TG1311:
Item
Meaning
Within range of a base unit
I
J
K
w
L When flashing: Out of range, no registration, or no
power on base unit
G
H
To stop paging
KX-TG1312/KX-TG1313:
To stop paging/Intercom
x
Paging, intercom mode, or accessing base unit
Making or answering a call
Phonebook mode
L
M
k
C
l
M Charge contacts
N Ringer
Setting mode
5
Battery level
0
New voice mail message received.*1 (page 17)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 8 Tuesday, September 2, 2008 10:36 AM
Preparation
Item
Meaning
Symbols used in these operating
instructions
Call bar is on. (page 13)
Direct call is on. (page 13)
Key lock is on. (page 10)
Symbol
{j/OK}
i
Meaning
Press {j/OK}.
Proceed to the next operation.
Ringer volume is off. (page 12)
Displayed when you press {#}.
{v}/{e}: “ ”
Press {v} or {e} to select the words in
quotations.
Example: {v}/{e}: “OFF”
Display language
If “BS NO” is selected for standby mode display
(page 13) and the current base unit number is 1, “-1-”
1 {j/OK}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “DISPLAY OPT” i {>}
4 {v}/{e}: “LANGUAGE” i {>}
If “HS NO” is selected for standby mode display
(page 13) and the current handset number is 2, “[2]”
is displayed.
5 {v}/{e}: Select your desired language. i {>} i {ih}
Note:
L If you select a language you cannot read: {ih} i {j/OK} i {v}
i {>} i {v} 3 times i {>} i {v} 2 times i {>} i
{v}/{e}: Select your desired language. i {>} i {ih}
4 new calls
When new calls have been received, the display shows the number of
new calls.
*1 Voice mail subscribers only
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 9 Tuesday, September 2, 2008 10:36 AM
Making/Answering Calls
M/wrl
Dialling mode
Making calls
1 Dial the phone number. i {C}
If you cannot make calls, change this setting according to your telephone
line service. The default setting is Tone.
“1” (Tone): For tone dial service.
2 When you finish talking, press {ih} or place the handset on the base
unit or charger.
“2” (Pulse): For rotary/pulse dial service.
1 {j/OK}
2 {v}/{e}: “SETTING BS” i {>} i {3}
Answering calls
3 Enter base unit PIN (default: “0000”). i {1}
1 Press {C} to answer the call.
L If you forget your PIN, see page 21.
L You can also answer the call by pressing any dial key from {0} to {9},
{*}, or {#}. (Any key answer feature)
4 Select the desired setting by pressing {1} for tone dialling mode or {2}
for pulse dialling mode.
2 When you finish talking, press {ih} or place the handset on the base
unit or charger.
5 {>} i {ih}
Handset locator
Date and time
1 Press {x} on the base unit.
2 To stop paging, press {x} on the base unit or press {C} or {INT} on
1 {j/OK}
2 {v}/{e}: “SETTING BS” i {>} i {*}
the handset.
3 Enter the current hour and minute (24-hour time entry).
Adjusting the receiver volume
L If you make a mistake, press {C}. Digits are cleared from the right.
Press {e} or {v} repeatedly while talking.
4 {>}
L A beep is heard.
Pause (for PBX/long distance service users)
5 {>} i {*} 2 times
A pause is sometimes required when making calls using a PBX or long
distance service. Pressing {R} 1 time creates a 3 second pause. Press
{R} repeatedly to create longer pauses.
6 Enter the current date, month, and year.
L If you make a mistake, press {C}. Digits are cleared from the right.
7 {>} i {ih}
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 10 Tuesday, September 2, 2008 10:36 AM
Making/Answering Calls
Redial functions (redialling/storing/editing before
calling/erasing)
For call waiting or Call Waiting Caller ID service users
To use call waiting, you must first subscribe to the call waiting service of
your service provider/telephone company.
This feature allows you to receive calls while you are already talking on the
phone. If you receive a call while on the phone, you will hear a call waiting
tone.
If you subscribe to both Caller ID and Call Waiting with Caller ID
services, the 2nd caller’s information is displayed after you hear the call
waiting tone on the handset.
1 {R} i {v}/{e}: Select the desired phone number.
2 ■ Redialling:
{C}
■ Storing:
{>} i {v}/{e}: “SAVE TEL NO” i {>} i {j/OK} i Enter
the name (9 characters max.; page 11). i {j/OK}
■ Editing before calling:
{>} i {v}/{e}: “EDIT CALL NO” i {>} i Edit the number.
i {C}
1 Press {R} to answer the 2nd call.
2 To switch between calls, press {R}.
Note:
■ Erasing:
{>} i {v}/{e}: “CLEAR”/“ALL CLEAR” i {>} i
{v}/{e}: “YES” i {>} i {ih}
L Please contact your service provider/telephone company for details and
availability of this service in your area.
Key lock
Temporary tone dialling (for rotary/pulse service users)
The handset can be locked so that no calls or settings can be made.
Incoming calls can be answered, but all other functions are disabled while
key lock is on.
Press {j/OK} for about 2 seconds to turn key lock on/off.
Note:
You can temporarily switch the dialling mode to tone when you need to
access touch-tone services (for example, telephone banking services).
1 Make a call.
2 Press {*} when prompted to enter your code or PIN, then press the
appropriate dial keys.
L Calls to emergency numbers cannot be made until key lock is turned off.
L The dialling mode will return to pulse when you hang up.
Recall/flash
{R} allows you to use the special features of your host PBX such as
transferring an extension call, or accessing optional telephone services.
Note:
L To change the recall/flash time, see page 14.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 11 Tuesday, September 2, 2008 10:36 AM
Phonebook
Making calls/editing/erasing
Adding entries to the phonebook
1 {k} i {v}/{e}: Select the desired entry.
The phonebook allows you to make calls without having to dial manually.
You can add 50 names and phone numbers.
2 ■ Making calls:
{C}
1 {j/OK} 2 times
2 Enter the party’s phone number (24 digits max.). i {j/OK}
3 Enter the party’s name (9 characters max.). i {j/OK}
4 {ih}
Note:
■ Editing:
{>} i {v}/{e}: “EDIT” i {>} i Edit the phone number. i
{j/OK} i Edit the name. i {j/OK}
■ Erasing:
{>} i {v}/{e}: “CLEAR” i {>} i {v}/{e}: “YES” i {>}
i {ih}
L When caller information is received and it matches a phone number
stored in the unit’s phonebook, the stored name is displayed.
Character table
Keys Characters
Keys Characters
{1}
{2}
{3}
{4}
{5}
#
[
]
* ,
2
–
/
1
{6}
{7}
{8}
{9}
{0}
M N
O
R
V
Y
6
S
8
Z
0
A
D
G
J
B
E
H
K
C
F
I
P
T
Q
U
7
9
3
4
W X
L
5
(Space)
Note:
L To enter another character located on the same dial key, press {>} to
move the cursor to the next space, then press the appropriate dial key.
Editing/correcting a mistake
1 Press {<} or {>} to move the cursor to the right of where you want to
correct the number/character.
2 {C} i Enter the correct number/character.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 12 Tuesday, September 2, 2008 10:36 AM
Useful Telephone Settings
Ufl ltt
One touch dialling (Hot key)
Guide to handset settings
To customise the handset (general approach):
Assigning an entry in the phonebook to a one touch dial key
1 {j/OK}
Dial keys {1} to {9} can each be used as a one touch dial key, allowing you
to dial a number from the phonebook by simply pressing a dial key.
2 Press {v} or {e} to select “SETTING HS”. i {>}
3 Press {v} or {e} to select the desired item in the handset settings
1 {k} i {v}/{e}: Select the desired entry. i {j/OK}
2 {v}/{e}: “HOT KEY REG” i {>}
3 {v}/{e}: Select the desired dial key. i {>}
L If the dial key is already assigned as a one touch dial key, the
displayed number flashes.
menu. i {>}
4 Press {v} or {e} to select the desired item in the sub-menu. i {>}
5 Press {v} or {e} to select the desired setting. i {>}
L This step may vary depending on the feature being programmed.
L To exit the operation, press {ih}.
4 {v}/{e}: “YES” i {>} i {ih}
Note:
L In the following table, < > indicates the default settings.
Making calls/cancelling a one touch dial assignment
1 Press and hold the desired one touch dial key ({1} to {9}).
Menu
Sub-menu
Page
13
—
2 ■ Making calls:
TIME ALARM
SET TIME
{C}
■ Cancelling a one touch dial assignment:
SET ALARM<OFF>
{>} 2 times i {v}/{e}: “YES” i {>} i {ih}
RINGER OPT
RINGER VOL<level 6>
EXT RINGER*1 <RING TYPE 1>
INT RINGER<RING TYPE 1>
PAGING<RING TYPE 1>
ALARM<RING TYPE 1>
KEY TONE<ON>
—
—
—
—
—
TONE OPT
—
CALL WAITING<ON>
RANGE ALARM<OFF>
BATTERY LOW<ON>
—
—
—
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 13 Tuesday, September 2, 2008 10:36 AM
Useful Telephone Settings
5 Enter the desired hour and minute (24 hour time entry). i {>}
6 {v}/{e}: Select the desired setting. i {>} i {ih}
Menu
Sub-menu
Page
—
DISPLAY OPT
STANDBY MODE<CLOCK>
TALK MODE<TALK TIME>
LANGUAGE<ENGLISH>
CALL BAR<OFF>
DIRECT NO
—
Call bar
8
Call bar feature prohibits outside calls from being made. When call bar is
turned on, only emergency calls can be made. To store emergency
numbers, see page 15.
CALL OPT
13
13
—
1 {j/OK}
SET DIRECT<OFF>
HSPIN CHANGE<0000>
AUTO TALK*2 <OFF>
—
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “CALL OPT” i {>}
4 {v}/{e}: “CALL BAR” i {>}
OTHER OPT
RESET HS
14
—
14
5 Enter handset PIN (default: “0000”).
*1 If you select a melody for the external ringer tone, the ringer continues
to sound until the melody finishes even when another person answers
the call using another phone connected to the same line. If you want the
*2 Auto talk feature allows you to answer calls simply by lifting the handset
off the base unit or charger. You do not need to press {C}. If you
subscribe to a Caller ID service and want to view the caller’s information
after lifting up the handset to answer a call, turn off this feature.
L If you forget your PIN, see page 21.
6 {v}/{e}: Select the desired setting. i {>} i {ih}
Direct call
Direct call feature allows you to dial a preset phone number simply by
pressing {C}. No dialling is necessary.
1 {j/OK}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “CALL OPT” i {>}
4 {v}/{e}: “DIRECT NO” i {>}
5 Enter a phone number (24 digits max.). i {j/OK} 2 times
Alarm
An alarm sounds at the set time for 3 minutes.
Important:
L Set the date and time beforehand (page 9).
6 {v}/{e}: “ON” i {>} i {ih}
1 {j/OK}
Note:
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “TIME ALARM” i {>}
4 {v}/{e}: “SET TIME” i {>}
L When this feature is turned on, only the direct call number can be called.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 14 Tuesday, September 2, 2008 10:36 AM
Useful Telephone Settings
Changing the handset PIN
Guide to base unit settings
For security, the handset PIN must be entered when changing certain
settings. If you change the PIN, please write down your new PIN as the unit
will not reveal it to you again.
To customise the base unit (general approach):
1 {j/OK}
1 {j/OK}
2 Press {v} or {e} to select “SETTING BS”. i {>}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “OTHER OPT” i {>}
4 {v}/{e}: “HSPIN CHANGE” i {>}
L “INPUT CODE” is displayed.
3 Enter the desired code number. Follow the instructions in the “Feature”
column of the chart.
L To exit the operation, press {ih}.
5 Enter the current 4-digit handset PIN.
L If you forget your PIN, see page 21.
Code No.
Feature (default setting)
6 Enter the new 4-digit handset PIN.
7 Enter the new 4-digit handset PIN again. i {ih}
{0}
Reset base unit to its default settings.*1
− Enter base unit PIN (default: “0000”).*2 i {>}
{3}
Dialling mode (Tone): page 9
Recall/flash time (600 ms)*3
− Enter base unit PIN (default: “0000”).*2 i {2} i
{1}
− Select the desired setting by pressing {1} for 100 ms,
{2} for 600 ms or {3} for 300 ms. i {>}
Resetting the handset
1 {j/OK}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “RESET HS” i {>}
4 Enter handset PIN (default: “0000”).
L If you forget your PIN, see page 21.
DTMF mode (Off): page 16
5 {v}/{e}: “YES” i {>} i {ih}
{5}
Change base unit PIN (“0000”).*4
− Enter the current 4-digit base unit PIN.*2
− Enter the new 4-digit base unit PIN.
− Enter the new 4-digit base unit PIN again.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 15 Tuesday, September 2, 2008 10:36 AM
Useful Telephone Settings
Code No.
Feature (default setting)
Code No.
Feature (default setting)
{6}
Call restriction*5
{*}
Date and time: page 9
■ Setting call restriction
*1 Only the emergency number setting is not reset.
*2 If you forget your PIN, see page 21.
*3 The recall/flash time depends on your telephone exchange or host PBX.
Contact your PBX supplier if necessary.
− Enter base unit PIN (default: “0000”).*2 i Enter
the desired handset number by pressing the
appropriate dial key.
L The selected handset number flashes on the
display.
*4 If you change the PIN, please write down your new PIN as the unit will
not reveal it to you again.
− {>}
*5 Call restriction feature restricts the handset from dialling certain phone
numbers. You can assign up to 10 phone numbers (memory locations
0–9) to be restricted.
− Enter the phone number to be restricted (8 digits
max.).
*6 Emergency number feature determines which phone numbers may be
dialled while the call bar feature is turned on. A total of 4 emergency
numbers (memory locations 1–4) can be stored.
L To select a different memory location, press {>}
and enter a number.
− {>}
■ Turning on/off call restriction
− Enter base unit PIN (default: “0000”).*2
L Handset number is displayed. A flashing number
indicates call restriction is on; a non-flashing
number indicates call restriction is off.
− Enter the desired handset number by pressing the
appropriate dial key to turn on/off. i {>} 2 times
Emergency number*6
− Enter base unit PIN (default: “0000”).*2 i {*}
■ Storing:
− Enter the emergency number (8 digits max.).
L To select a different memory location, press
{>} and enter a number.
− {>}
■ Editing:
Press {>} to display the desired number. i {C}
i Enter the new emergency number. i {>}
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 16 Tuesday, September 2, 2008 10:36 AM
Caller ID Service
ClI
DTMF mode setting
Using Caller ID service
Certain service providers/telephone companies send caller information
between the first and second rings. If the display does not show caller
information after a few rings, follow these instructions to set DTMF mode.
Important:
L This unit is Caller ID compatible. To use Caller ID features, you must
subscribe to a Caller ID service. Contact your service provider/telephone
company for details.
1 {j/OK}
2 {v}/{e}: “SETTING BS” i {>} i {3}
3 Enter base unit PIN (default: “0000”). i {4}
Caller ID features
L If you forget your PIN, see page 21.
4 Select DTMF mode by pressing {2}.
Display indications
5 {>} i {ih}
L When new calls have been received, the display shows the number of
new calls.
L To cancel DTMF mode, press {1} in step 4.
Example: 4 new calls have been received.
Storing/editing/erasing
1 {v}/{e}: Select the desired entry. i {>}
2 ■ Storing:
{v}/{e}: “SAVE TEL NO” i {>} i {j/OK} i Enter the
party’s name (9 characters max.; page 11). i {j/OK} i {ih}
■ Editing:
{v}/{e}: “EDIT CALL NO” i {>} i Press {<} or {>} to move
the cursor to the right of where you want to edit the number. i Edit
the phone number. i {C}
L Phone numbers of the last 50 different callers are logged in the caller list.
Example:
*1
■ Erasing:
{v}/{e}: “CLEAR”/“ALL CLEAR” i {>} i {v}/{e}: “YES” i
{>} i {ih}
*1 Shown when this call has already been viewed or answered.
Press {C} to call back.
L If the unit cannot receive caller information, the following is displayed:
− “OUT OF AREA”: The caller dials from an area which does not provide a
Caller ID service.
− “PRIVATE”: The caller requests not to send caller information.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 17 Tuesday, September 2, 2008 10:36 AM
Multi-unit Operation
Mt-iOrti
Voice mail service
Intercom
Voice mail is an automatic answering service offered by your service
provider/telephone company. After you subscribe to this service, your
service provider/telephone company’s voice mail system answers calls for
you when you are unavailable to answer the phone or when your line is
busy. Messages are recorded by your service provider/telephone
company, not your telephone.
When you have new messages, 0 is displayed on the handset
depending on your service provider/telephone company. Please contact
your service provider/telephone company for details of this service.
Important:
Available for:
KX-TG1312/KX-TG1313
Intercom calls can be made between handsets.
Example: When handset 1 calls handset 2
1 Handset 1:
{INT} i Press {2} (desired handset number).
2 Handset 2:
{C}
3 When you finish talking, press {ih}.
L If 0 still remains on the display even after you have listened to new
messages, turn it off by pressing {<} for 1 second.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 18 Tuesday, September 2, 2008 10:36 AM
Useful Information
Ufl Ifrti
Transferring calls, conference calls
Troubleshooting
If you still have difficulties after following the instructions in this section,
disconnect the base unit’s AC adaptor and turn off the handset, then
reconnect the base unit’s AC adaptor and turn on the handset.
Available for:
KX-TG1312/KX-TG1313
Outside calls can be transferred between 2 handsets. 2 handsets can have
a conference call with an outside party.
Problem
Cause/solution
Example: When handset 1 transfers a call to handset 2
1 Handset 1:
w is flashing.
L The handset is too far from the base
unit. Move closer.
During an outside call, press {INT}. i Press {2} (desired handset
number).
L The base unit’s AC adaptor is not
connected. Check the connections
(page 4).
L The outside call is put on hold.
L If there is no answer, press {INT} to return to the outside call.
L You are using the handset or base unit
in an area with high electrical
interference. Re-position the base unit
and use the handset away from
sources of interference.
2 Handset 2:
Press {C} to answer the page.
L Handset 2 can talk with handset 1.
3 Handset 1:
L The handset registration is cancelled.
Register the handset to the base unit
(page 20).
To complete the call transfer, press {ih}.
To establish a conference call, press {3}.
Transferring a call without speaking to the other handset user
1 During an outside call, press {INT}. i Enter the desired handset
number.
L k flashes to indicate the outside call is on hold.
2 {ih}
L The outside call rings at the other handset.
Note:
L If the other handset user does not answer the call within 30 seconds, the
call rings at your handset again.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 19 Tuesday, September 2, 2008 10:36 AM
Useful Information
Problem
Cause/solution
Problem
Cause/solution
I cannot make or receive
calls.
L The base unit’s AC adaptor or
telephone line cord is not connected.
Check the connections.
Noise is heard, sound
cuts in and out.
L You are using the handset or base unit
in an area with high electrical
interference. Re-position the base unit
and use the handset away from
sources of interference.
L The call bar feature is turned on. Turn it
off (page 13).
L Move closer to the base unit.
L If you use a DSL/ADSL service, we
recommend connecting a DSL/ADSL
filter between the base unit and the
telephone line jack. Contact your DSL/
ADSL provider for details.
L You dialled a call restricted number
(page 15).
L The key lock feature is turned on. Turn
it off (page 10).
L The dialling mode may be set
(page 9).
I fully charged the
batteries, but 7 still
flashes.
L Clean the charge contacts and charge
again (page 6).
The unit does not ring.
L The ringer volume is turned off. Adjust
L It is time to replace the batteries
(page 6).
The handset display is
blank.
L The handset is not turned on. Turn the
I fully charged the
batteries, but the
operating time seems to
be shorter.
L Clean the battery ends (S, T) and the
charge contacts with a dry cloth, and
charge again.
power on (page 6).
The handset will not turn
on.
installed correctly (page 6).
L Fully charge the batteries (page 6).
I have changed the
L Change the display language (page 8).
display language to a
language I cannot read.
A busy tone is heard
L The handset is too far from the base
when {C} is pressed.
unit. Move closer and try again.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 20 Tuesday, September 2, 2008 10:36 AM
Useful Information
Problem
Cause/solution
Liquid damage
Problem
Caller information is not
displayed.
L You must subscribe to a Caller ID
service. Contact your service provider/
telephone company for details.
L If your unit is connected to any
additional telephone equipment,
remove and plug the unit directly into
the wall jack.
Cause/solution
Liquid or other form of
moisture has entered the
handset/base unit.
L Disconnect the AC adaptor and
telephone line cord from the base unit.
Remove the batteries from the handset
and leave to dry for at least 3 days.
After the handset/base unit are
completely dry, reconnect the AC
adaptor and telephone line cord. Insert
the batteries and charge fully before
use. If the unit does not work properly,
contact your nearest Panasonic service
centre.
L If you use a DSL/ADSL service, we
recommend connecting a DSL/ADSL
filter between the base unit and the
telephone line jack. Contact your DSL/
ADSL provider for details.
L Other telephone equipment may be
interfering with this unit. Disconnect the
other equipment and try again.
Caution:
L To avoid permanent damage, do not use a microwave oven to speed up
Caller information is slow
to display.
L Depending on your service provider/
telephone company, the unit may
display the caller’s information at 2nd
ring or later.
the drying process.
Registering the handset to the base unit
1 {j/OK}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “REGISTRATION” i {>}
4 {v}/{e}: “REGISTER HS” i {>}
L Move closer to the base unit.
I cannot remember the
PIN.
L Change the PIN using the instructions
on page 21.
5 Press and hold {x} on the base unit for about 5 seconds.
L If all registered handsets start ringing, press {x} to stop, then start
again from step 1.
L The rest of the procedure must be completed within 4 minutes.
6 {v}/{e}: Select a base unit number. i {>}
7 Wait until “BS PIN” is displayed. i Enter the base unit PIN (default:
“0000”). i {>}
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 21 Tuesday, September 2, 2008 10:36 AM
Useful Information
L If you forget your PIN, see page 21.
L When the handset has been registered successfully, w stops
flashing.
Specifications
L If w is still flashing, start again from step 1.
■ Standard:
DECT (Digital Enhanced Cordless Telecommunications)
■ Number of channels: 120 Duplex Channels
■ Frequency range: 1.88 GHz to 1.90 GHz
■ Duplex procedure:
TDMA (Time Division Multiple Access)
■ Channel spacing: 1,728 kHz
■ Bit rate: 1,152 kbit/s
Changing the handset PIN
1 {j/OK}
2 {v}/{e}: “SETTING HS” i {>}
3 {v}/{e}: “OTHER OPT” i {>}
4 {v}/{e}: “HSPIN CHANGE” i {>}
5 {*}{7}{0}{0}{0}
■ Modulation:
GFSK (Gaussian Frequency Shift Keying)
■ RF transmission power:
Approx. 10 mW (average power per channel)
■ Voice coding: ADPCM 32 kbit/s
■ Power source:
6 Enter the new 4-digit handset PIN.
7 Enter the new 4-digit handset PIN again.
8 {ih}
Changing the base unit PIN
1 {j/OK}
220–240 V AC, 50/60 Hz
■ Power consumption:
2 {v}/{e}: “SETTING BS” i {>}
3 {5}
4 {*}{7}{0}{0}{0}
Base unit:
Standby: Approx. 2.1 W
Maximum: Approx. 5.7 W
Charger*1:
5 Enter the new 4-digit base unit PIN.
6 Enter the new 4-digit base unit PIN again.
7 {ih}
Standby: Approx. 1.1 W
Maximum: Approx. 5.2 W
■ Operating conditions:
5 °C–40 °C, 20 %–80 % relative air humidity (dry)
■ Dimensions:
Base unit: Approx. 103 mm × 104 mm × 58 mm
Handset: Approx. 148 mm × 50 mm × 33 mm
Charger: Approx. 87 mm × 75 mm × 53 mm
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 22 Tuesday, September 2, 2008 10:36 AM
Useful Information
■ Mass (weight):
Base unit: Approx. 120 g
Handset: Approx. 120 g
Charger: Approx. 60 g
*1 KX-TG1312/KX-TG1313
Note:
L Design and specifications are subject to change without notice.
L The illustration in these instructions may vary slightly from the actual
product.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 23 Tuesday, September 2, 2008 10:36 AM
Notes
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TG1311_1312_1313BX(e).book Page 24 Tuesday, September 2, 2008 10:36 AM
For your future reference
We recommend keeping a record of the following information to assist with
any repair under warranty.
Serial No.
Date of purchase
(found on the bottom of the base
unit)
Name and address of dealer
Attach your purchase receipt here.
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and
may be reproduced for internal use only. All other reproduction, in whole or
in part, is prohibited without the written consent of Panasonic
Communications Co., Ltd.
© Panasonic Communications Co., Ltd. 2008
Panasonic Communications Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|