Heavy Duty CD player/weather Band Receiver with CD changer Control
CQ-5335U
CLK
ALM
PWR
Operating Instructions
CQ-5335U
DISC
VOLPUSH
SEL/SAT
DISP
LOUD
MODE
MUTE
TUNE
SEEK
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
• Please read these instructions carefully before using this product and keep this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
We welcomes you to our ever growing family of electronic product owners. We know that this product will
bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering,
manufactured with carefully selected components and assembled by people who take pride in their work. Once
you discover the quality, reliability, and value we have built into this product, you too will be proud to be a
member of our family.
❐ Use this product safely
When Driving
Keep the volume level low enough to be aware of
road and traffic conditions.
Disc Mechanism
Do not insert coins or any small objects. Keep
screwdrivers and other metallic objects away from
the disc mechanism and disc.
When Washing Your Car
Do not expose the product, including the speakers
and CDs, to water or excessive moisture. This could
cause electrical shorts, fire, or other damage.
Use Authorized Service centers
Do not attempt to disassemble or adjust this
precision product. Please refer to the Service center
list included with this product for service assistance.
When Parked
Parking in direct sunlight can produce very high
temperatures inside your car. Give the interior a
chance to cool down before switching the unit on.
For Installation
The product should be installed in a horizontal
position with the front end up at a convenient angle,
but not more than 30˚.
Use the Proper Power Supply
This product is designed to operate with a 12 V DC,
negative ground battery system.
1. Operating Instructions ..................................................................................................1
2. Supplied Hardware.............................................................................1 set (➡ page 23)
3. Warranty Card...............................................................................................................1
Accessories
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Contents
Safety Information(Part 15 of the FCC Rules). . . . . . . . . . . . . . . . . Page 2
Use this product safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
❒ Power and Sound Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power, volume, mute, loudness, Illumination switching, audio mode
(Bass/Treble/Balance/Fader)
❒ Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Initial time, time reseting
❒ Alarm Time Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Initial alarm time, alarm time setting and reset, alarm operation,
alarm output volume selection
❒ Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Radio mode, band, manual tuning, seek tuning, preset station setting,
preset station calling, Weather Band Stations
FM
❒ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disc insert and playback, stop and disc eject, listening to a CD,
track selection, track search, repeat play, random play, scan play
❒ CD changer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CD Changer mode, Disc Selection, Track Selection, Track Search, scan
play, repeat play, random play
Note: CD changer controls are applicable to units with optional CD changer
unit (sold separately)
❒ Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Note: Remote controls are available to an optional Remote control unit
CA-RC500U (sold separately)
❒ Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting tips, Error Display Messages
❒ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Care of the unit, notes on discs, notes on CD-Rs/RWs
❒ Speaker Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
❒ Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation hardware, overview, required tools dashboard specifications,
preparation, to remove the unit
❒ Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cautions, wiring diagram
❒ Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Power and Sound Controls
Power
Turn the key in the ignition until the
accessory indicator lights.
Power on: Press [PWR] (power).
Power off: Press [PWR] (power) again.
C
AC
ON
Remote Control Signal Sensor
Point the remote control unit
(CA-RC 500U, option) toward
the unit's sensor.
CLK
ALM
PWR
CQ-5335U
DISC
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
CD SCAN
RPT
RDM
BAND
APM
SCAN
IL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
Volume
Turn the knob clockwise to increase volume,
and counterclockwise to decrease volume.
Loudness
Press and hold [MUTE] (LOUD) for more
than 2 seconds to enhance bass and treble
tones when listening at low or medium
volume.
Volume level (0 to 40)
(default:18)
Press and hold [MUTE] (LOUD) for more
than 2 seconds again to deactivate when
listening at higher volumes.
Up
Mute
Down
Press [MUTE] to mute the sound completely.
Press [MUTE] again to cancel.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Power and Sound Controls
(Continued)
Note: If no operation takes place for more than 5
seconds in audio mode (2 seconds in
volume mode), the display returns to the
regular mode.
Audio Modes
(Bass/Treble/Balance/Fader)
q Push [SEL] to select the audio mode.
Volume
Bass
Audio Mode
Fader
Balance
Treble
push
CLK
ALM
PWR
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MODE
MUTE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
SCAN
1
2
3
4
5
6
BASS/TREB/BAL/FADER
ILL
APM
Turn [VOL] (volume) clockwise or
counterclockwise to change each level.
w
Illumination Switching
Press [SCAN] (ILL) for more than 2 seconds
to switch the illumination color (green/amber).
Bass:
default : 0 dB
Adjustable range: –12 to +12 dB (by 3 dB step)
Treble:
default : 0 dB
Adjustable range: –12 to +12 dB (by 3 dB step)
Balance:
R (right speaker) or L (left speaker)
Adjustable range:
1 to 15 (by 1 step)
Balance center
(default)
Fader:
F (front speaker) or R (rear speaker)
Adjustable range:
1 to 15 (by 1 step)
Fader center
(default)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Clock Setting
The 12-hour system is used for the clock.
Selecting the Clock Display
Press [CLK] (clock) to switch clock and alarm time
display both.
Initial Time
clock display
Alarm time display
“SET” is displayed when the clock is not adjusted.
Note: if no operation takes place for more than 5
seconds in alarm time, the display returns to the
clock display.
CLK
PWR
ALM
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MODE
MUTE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
1
2
3
4
5
6
BASS/TREB/BAL/FADER
ILL
[{ TUNE], [} TUNE]
Time Setting
(Hours, Minutes)
q Press and hold [CLK] (clock) and do not release
to set time. Display blinks and the time setting
mode is activated.
(blink.)
Hours
w Press [{] to set the hour.
(Hours set.)
Minutes
e Press [}] to set the minute.
(Minutes set.)
r Once the time has been set, release [CLK].
Time Reset
When you want to reset the time, repeat steps q to
(End.)
r.
Note: Press and hold [{] or [}] to change
Note: the current time will be displayed at all the
numbers rapidly.
time even the power of the radio is turned off.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Alarm Time Setting
The 12-hour system is used for the clock.
Initial Alarm Time
Press and hold [ALM] (Alarm)
“AM 12:00” is displayed when the alarm is not adjusted.
CLK
PWR
ALM
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
[{ TUNE], [} TUNE]
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
(Hours, Minutes)
1
2
3
4
5
6
BASS/TREB/BAL/FADER
Alarm Time Setting
q Press and hold [ALM] (Alarm) and do not
release to set alarm time. Display blinks and
the alarm time setting mode is activated.
Alarm Operation
• Alarm is switched to ON or OFF each time [ALM] is pressed.
• When the alarm is switched to ON, the alarm will sound at the set
alarm time.
Turning off the Alarm Sound
(blink.)
The alarm will turn off automatically after 90 seconds. Otherwise,
press [ALM] once.
Hours
w Press [{] to set the hour.
Alarm output Volume Selection
(Hours set.)
You can select ALARM VOL 1 (or VOL 2) by pressing [ALM] in
sequence and the display will show as follows.
Minutes
e Press [}] to set the minute.
a
a
OFF
(Minutes set.)
r Once the alarm time has been set, release [ALM].
Note: Press and hold [{] or [}] to change
numbers rapidly.
Cautions:
Alarm Time Reset
• Be careful not to set wrong alarm time, otherwise, the alarm
may sound while driving.
• If the alarm is set, be sure to check the set alarm time by
pressing [CLK].
When you want to reset the alarm time, repeat
steps q to r.
• If volume is set at “0” level, the output volume will be muted.
(Even when ALARM is acting.)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Radio
q
Radio Mode
Press [MODE] to change to the radio mode.
Radio
CD Player
CD Changer Control
a
a
c
( When a CD changer is connected )
( When CD disc loaded )
FM stereo indicator
CLK
ALM
PWR
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
w
e
r
Band
Press [BAND] to change the band.
Scan
• Press [SCAN], each station will be scanned sequentially and the display
will blink for 5 seconds.
• Press [SCAN] again to stop scanning and the last station will continue to
broadcast.
Manual Tuning
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Seek Tuning
Press and hold for more than 0.5 seconds and release it.
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Tuning will automatically stop when the next broadcast
station is received.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Radio
(Continued)
Preset Station Setting
Up to 6 stations can be saved in each of the FM1, FM2
and AM preset station memories.
Note: Existing saved stations are overwritten with new
stations after following this procedure.
q
Band
Press [BAND] to select a desired band.
(➡ page 9)
CLK
PWR
ALM
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
Preset buttons from [1] to [6]
w Auto Preset Memory (APM)
Press and hold [BAND] (APM: auto preset memory) for more
than 2 seconds.
• The 6 stations with good reception will be automatically
saved in the memory under preset buttons from [1] to [6].
• Once set, the preset stations are sequentially scanned for 5
seconds each.
• Press [BAND] again to stop sequentially scan.
Manual Preset Memory
q Use manual or seek tuning to find a station. (➡ page 9)
w Press and hold one of the preset buttons from [1] to [6]
until the display blinks once.
blinks once
Preset Station Calling
Caution: To ensure safety, never attempt to preset stations
while you are driving.
Press the corresponding preset button from [1]
to [6] to tune in a preset station.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
CLK
ALM
PWR
CQ-5335U
DISC
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
Tuning in a Weather Band Station
• Press [BAND] to select WB (Weather Band). (a page 9)
• Press any of the buttons [1] to [6] to monitor the preset station.
WB
Weather Band Frequency (channel) Number
Note: The weather band (CH1-6) has been preset. CH7 is selected by
pressing [}] or [{].
Weather Band Stations
National Weather Radio Broadcasts from over 380 Iocations throughout the
U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information 24 hours
a day on one of the following frequencies.
1. 162.550 MHz
2. 162.400 MHz
3. 162.475 MHz
4. 162.425 MHz
5. 165.450 MHz
6. 162.500 MHz
7. 162.525 MHz
Occasionally the frequency of an existing or planned station must be
changed because of unexpected radio frequency interfere with adjacent
NOAA weather Radio Stations and/or with other Government or
commercial Operations within the area. If you have a question concerning
NOAA Weather Radio, please contact your nearest National Weather
Service Office.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
CD Player
Disc Insert and Playback
Disc insert
Playback will start automatically after the player recognized
the loaded disc as an ordinary music CD. (When a CD-R or
CD-RW which has CD-DA formatted data as the same as an
ordinary music CD is loaded, this player recognizes it as an
ordinary music CD.)
u (eject)
U
5
3
3
-5
Q
C
“LOAd” will be displayed until the disc is loaded.
Label Side
Notes:
• Do not insert a disc when “DISC” indicator lights.
• The power will be turned on automatically when a disc is
loading.
Stop and Disc Eject
Press [u] (eject) to stop CD play and eject the disc.
During disc ejection, “CD EJECT” will be displayed.
Listening to a CD
Press [MODE] to change to the CD player mode.
Playback will start automatically when a disc is loaded.
( When CD disc loaded )
CD player
Radio
CLK
ALM
PWR
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
1
2
3
4
5
6
BASS/TREB/BAL/FADER
ILL
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Cautions:
• Only 5" (12 cm) CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
• This unit does not support CD text display.
• This unit does not support MP3 and WMA disc playback.
• Refer to page 20 about notes on CD-Rs/RWs.
• This unit is not designed for any 3" (8 cm) disc.
• If you insert an 3" (8 cm) disc and can not eject it, turn ACC of your car off once and turn it on again, then press
[u] (eject).
• Do not use irregular shaped discs.
• Do not use discs that have a seal or label attached.
• Do not insert foreign matter into the disc slot.
CLK
PWR
ALM
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
Track Selection
Track Search
Press [2 TRACK]: Advance to the next track.
Press and hold...
Press [1 TRACK]: Back to the beginning of the current
[2 TRACK]: Fast forward
[1 TRACK]: Fast reverse
Release to resume the regular play.
track.
Back to the previous track. (Press
twice.)
• Press [5] (RPT) .
The current track is repeated.
• Press [5] (RPT) again to cancel.
Repeat play
• Press [6] (RDM).
All the tracks are played in random order.
• Press [6] (RDM) again to cancel.
Random play
Scan play
• Press [4] (CD SCAN).
The first 10 seconds of each track on the
disc are played in sequence.
• Press [4] (CD SCAN) again to cancel.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
CD Changer Control
q CD Changer mode
While a disc magazine is inserted in the CD changer, press [MODE] to select CD changer mode.
Play starts from the first track.
CLK
PWR
ALM
CQ-5335U
VOLPUSH
SEL/SAT
DISP
LOUD
MUTE
MODE
TUNE
SEEK
DISC
CD SCAN
RPT
RDM
BAND
APM
SCAN
ILL
1
2
3
4
5
6
BASS/TREB/BAL/FADER
w Disc Selection
[1] ({ DISC): Previous disc.
[2] (} DISC): Next disc.
e Track Selection
Press [TRACK 2] once to go to the next track. Press
repeatedly to step forward through all the tracks.
Press [TRACK 1] once to play from the beginning of the
current track, Press twice to play the previous track. Press
repeatedly to step backward through all the tracks.
Track Search
Press and hold [TRACK 2] or [TRACK 1] for more
than 0.5 seconds to activate fast forward or reverse through
a track. Release it to resume the normal CD play from that
position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Note:
CD changer functions are applicable to units with optional CD changer unit.
(sold separately)
• Press [4] (CD SCAN). The track number blinks
and the first 10 seconds of each track on the
blinks
Scan Play
discs play in sequence.
• Press [4] (CD SCAN) again to cancel and
continue with the current track.
(Tracks)
• Press and hold [4] (CD SCAN) for more than 2
seconds. The first track of all the discs in the
magazine is played for 10 seconds each and
Disc Number blinks.
• Press and hold [4] (CD SCAN) for more than 2
blinks
Scan Play
(Discs)
seconds again to cancel.
lights REP: Repeat lndicator
blinks REP: Repeat lndicator
lights R̈: Random Indicator
Repeat Play
• Press [5] (RPT) to repeat the current track.
• Press [5] (RPT) again to cancel.
(Tracks)
• Press and hold [5] (RPT) for more than 2
seconds to repeat the current disc.
• Press and hold [5] (RPT) for more than 2
seconds again to cancel.
Repeat Play
(Discs)
• Press [6] (RDM) to random selection. Music is
played from all available CDs.
Random Play
• Press [6] (RDM) again to cancel.
(Tracks)
• Press and hold [6] (RDM) for more than 2
seconds all the available tracks on the current
blinks R̈: Random Indicator
Random Play
disc play in a random sequence.
• Press and hold [6] (RDM) for more than 2
seconds again to cancel
(Discs)
❐ Remote Control
CA-RC500U (option)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Troubleshooting
Preliminary Steps
Cautions:
Check and take steps as described in the tables below.
• Do not use the unit if it malfunctions or if there is
something wrong.
• Do not use the unit in irregular condition, for
example, without sound, or with smoke or foul
smell, which can cause ignition or electric shock.
Immediately stop using it and call the store where
you purchased it.
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is
neither smoke nor heat from the unit before asking for
repairs. Never try to repair the unit by yourself because it
is dangerous to do so.
Troubleshooting Tips
❐ Common
Trouble
Cause/Step
Vehicle’s ignition switch is not on.
a Turn your vehicle’s ignition switch to ACC or ON.
Cables are not correctly connected.
a Connect cables correctly.
Power connector is not correctly connected.
a Connect the power connector to the terminal that is always active.
No power.
Power connector is not correctly connected.
a Connect the power connector to your vehicle’s ACC source.
Grounding wire is not correctly connected.
a Connect the grounding wire to a metal part of the vehicle.
Mute is set to ON.
a Set it to OFF.
No sound.
Noise.
Cables are not correctly connected.
a Connect cables correctly.
The ground lead is not connected properly.
a Connect the ground lead properly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Troubleshooting
❐ Radio
(Continued)
Trouble
Cause/Step
Station is too far, or signals are too weak.
Much noise in FM stereo
and monaural broad-
casts.
a Select other stations of higher signal level.
The radio antenna is not extended enough.
a Extend fully the radio antenna.
Battery cable is not correctly connected.
a Connect the battery cable to the terminal that is always active.
Preset station is reset.
❐ CD
Trouble
Cause/Step
Disc is upside down.
a Place disc in the correct direction with the label side up.
• Disc is dirty.
• Disc has scratches.
a Clean disc, referring to the section on “Notes on Discs”.
Disc is in the CD
compartment but no
sound is made, or disc is
ejected automatically.
A disc that has data other than CD-DA type is loaded.
a Discs that have CD-DA type data should be used.
a The unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
• Disc is dirty.
• Disc has scratches.
a Clean disc, referring to the section on “Notes on Discs”.
Sound skips, bad sound
quality. (e.g. caused by
noise)
a The unit may not successfully playback a CD-R/RW that is made in
combination of writing software, a CD recorder (CD-R/RW drive) and a
disc which are incompatible one another. Refer to instructions for the
concerned devices for details.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
❐ CD (Continued)
Trouble
Cause/Step
Mounting angle is over 30˚.
a Adjust mounting angle to less than 30˚.
Sound skips due to
vibration.
Instable mounting.
a Mount the unit securely with the mounting parts, referring to the
section on installation.
• Disc is defective.
• Mechanical trouble.
Disc is not ejected.
a Press [u] (eject). If normal operation is not restored, call the store
where you purchased the unit or the nearest Service center to ask for
repairs.
The first track of a mix mode disc was reproduced. (Mix mode is a format in
which data except music is recorded on the first track and music data is
recorded on other than the first track in a session.)
Time is counted but no
sound comes out.
a Playback music data recorded on other than the first track.
❐ Sound Setting
Trouble
Cause/Step
Left and right balance, or front and rear balance is off on one side.
a Adjust BAL/FAD as appropriate.
No sound from left, right,
front, or rear speaker.
Cables are not correctly connected.
a Connect the cables correctly.
Left and right sounds are
reversed in stereo
listening.
The right speaker wire is connected to the left speaker and the left speaker
wire to the right speaker.
a Connect the speaker wires to the correct ones.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Troubleshooting
(Continued)
Error Display Messages
❐ CD
Trouble
Cause/Step
Disc is dirty, or is upside down.
A disc that has data other than CD-DA type is loaded.
➡ Check the disc.
Disc has scratches.
➡ Check the disc.
No operation by some cause.
➡ If normal operation is not restored, call the store where you purchased
the unit or the nearest Service center to ask for repairs.
❐ CD changer
Disc is dirty, or is upside down.
➡ Select the next available compact disc. Check the disc.
Disc has scratches.
➡ Select the next available compact disc. Check the disc.
No operation by some cause.
➡ Eject the magazine. If failure persists, press the reset switch on the CD
changer. If normal operation is not restored yet, call the store where you
purchased the unit to the nearest panasonic service center to ask for
repairs.
No disc in the changer (magazine)
➡ Insert discs into the changer (magazine).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Maintenance
Care of the Unit
❐ Caution on Cleaning
❐ Cleaning this Unit
Use a dry, soft cloth to wipe.
Never use solvents such as benzine, thinner as they
may mar the surface of the unit.
Notes on Discs
Do not play any ordinary music CDs with labels
other than this one.
How to hold the disc
• Do not touch the underside of the disc.
• Do not scratch the discs.
Label side
• Do not bend disc.
• When not in use, keep the disc in the case.
Do not use irregular shaped discs.
• Transparency discs maybe can not be played back
Do not leave discs on the following places:
• Direct sunlight
• Near car heaters
Do not use irregular shaped discs.
• Dirty, dusty and damp areas
• Seats and dashboards
<Right>
<Wrong>
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or
ballpoint pen stroke.
Notes on CD-Rs/RWs
• You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to
their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
• CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them
inside a vehicle for extended periods may damage them and make playback impossible.
• The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a CD
recorder (CD-R/RW drive) and a disc if they are incompatible one another.
• This player cannot play the CD-R/RW discs if the session is not closed.
• This player cannot play the CD-R/RW discs which contains other than CD-DA data.
• Be sure to observe the instructions of CD-R/RW disc for handling it.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Speaker Connections
Caution: Please follow the instructions given below. Failure to do so will cause damage to the unit and speakers.
<Right>
• Use ungrounded speaker only.
• The maximum speaker input should be 37 W or more. (If used with the optional
power amplifier, the speaker input should be higher than the maximum amplifier
output.)
(White)
+
-
+
L
-
(White
w/black stripe)
• The speaker impedance should be 4 - 8 1.
• This unit uses the BTCL circuit, so each speaker should be connected separately
using parallel vinyl insulated cords.
• The speaker cords and the power amplifier unit should be kept away (about 30 cm
apart) from the antenna and antenna extension cord.
(Gray)
+
-
+
R
-
(Gray
w/black stripe)
<Wrong>
+
-
+
-
+
-
+
+
-
+
+
L
L
L
-
-
-
Chassis
Chassis
+
-
+
-
+
-
+
+
-
+
+
R
R
R
-
-
-
• Never connect the speaker cord to
the body of the car.
• Do not use a 3-wire type speaker
system having a common earth
lead.
• Do not connect more than one
speaker to one set of speaker
leads.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized
Panasonic Service center. The product should be serviced only by a qualified technician.
Maintenance
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
Caution
This product is designed without a fuse inside due to fuses already exist in your vehicle. We would recommend to use
fuses of the specified rating (10 A). Using fuses that exceed the prescribed capacity could cause this product to start
smoking, ignite or other malfunction.
If your vehicle is without the fuse or a circuit braker to protect this unit ,please your dealer add the specified fuse 10 A
or a circuit breaker at the BATTERY lead of your vehicle's harness. please see page 26 to find out where "BATTERY +
12 V" is for your dealer adding the fuse or the circuit breaker.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Installation Guide
WARNING
❐ This installation information is designed for experienced installers and is not
intended for non-technical individuals. It does not contain warnings or cautions of
potential dangers involved in attempting to install this product.
Any attempt to install this product in a vehicle by anyone other than a qualified
installer could cause damage to the electrical system and could result in serious
personal injury or death.
❐ If your vehicle is equipped with air bag and/or anti-theft systems, specific procedures
may be required for connection and disconnection of the battery to install this product.
Before attempting installation of this electronic component, contact your vehicle
dealer or manufacturer to determine the required procedure and strictly follow their
instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOY-
MENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN
DAMAGE TO THE VEHICLE AND PERSONAL INJURY.
…Keep for future reference in case the product needs
servicing.
• Installation Hardware…Needed for in-dash installation.
❐ Overview
This product should be installed by a professional.
However, if you plan to install this product yourself,
❐ Dashboard Specifications
your first step is to decide where to install it. The
instructions in these pages will guide you through the
remaining steps:
3
Thickness Min. ⁄16" (4.75 mm)
7
Max. ⁄32" (5.56 mm)
(Please refer to the “WARNING” statement above.)
• Identify and label the car wires.
• Connect the vehicle wires to the wires of the power
connector.
3
2 ⁄32" (53 mm)
• Install the unit in the dashboard.
• Check the operation of the unit.
5
7 ⁄32" (182 mm)
If you encounter problems, please consult your nearest
professional installer.
Caution: This unit operates with a 12 V DC negative
ground auto battery system only. Do not attempt to
use it in any other system. Doing so could cause
serious damage.
Before you begin installation, look for the items which
are packed with your unit.
• Warranty Card…Fill this out promptly.
• Panasonic Servicenter List for Service Directory
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Installation
❐ Preparation
(Continued)
❐ Installation Hardware
Warning: If your vehicle is equipped with air bag
and/or anti-theft systems, specific procedures may
be required for connection and disconnection of the
battery to install this product.
No.
Item
Diagram Q’ty
Mounting Collar*
1
q
Before attempting installation of this electronic
component, contact your vehicle dealer or
manufacturer to determine the required procedure
and strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE
AND PERSONAL INJURY.
Plain washer (5mmø)
Spring Washer (5mmø)
Hex. Nut (5mmø)
2
2
2
1
1
1
2
1
w
e
r
t
y
u
i
o
Rear Support Strap
Hex. Bolt
(5mmø × 25 mm)
• Disconnect the cable from the negative
terminal (see warning and caution below).
battery
Toothed Lock Washer
(5mmø)
• Remove Mounting Collar q from the main unit
temporarily, which are already mounted at shipment.*
Removal Tool
(U-shaped)
Caution: Various settings that have been stored in
the memory in other on-board equipment (vehicle
navigation etc.) may be lost if the battery terminals
are disconnected.
Antenna Connector
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the
terminals.
After completing installation of the main unit, set the
equipment again according to the record.
(a) Using the rear support strap t
• Unit should be installed in a horizontal position with
the front end up at a convenient angle, but not more
than 30˚.
❐ Dashboard Installation
Installation Opening
(b) Using the rubber cushion (option)
This unit can be installed in any dashboard having an
opening as shown below. The dashboard should be
3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be
able to support the unit.
Rear support bracket
Rubber cushion (option)
(provided on the vehicle)
Mounting bolt
(5 mmø)
q Mounting collar
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Cautions:
• We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
• When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands
and fingers.
First complete the electrical connections, and then check them for correctness.(a page 26)
The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model.
Insert Mounting Collar q into the
dashboard, and bend the mounting tabs
out with a screwdriver.
1
The tabs to be bent vary depending on
the vehicle. To securely install the unit,
fully bend a number of the tabs so that
there is no rattling.
Example:
Tab
q Mounting
Power Connector
Collar
Mounting Holes
Mounting Bolt
Establish the rear connection of the unit.
After fixing Power Connector, fix the rear of the unit
to the vehicle body by either method (a) or (b)
shown in the previous page.
2
Mounting springs (C)
After installation reconnect the negative
(–) battery terminal.
3
Engage the Mounting
Springs (C) in the
Mounting
Hole
mounting holes of the
Mounting Collar q
firmly.
Mounting Spring
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Installation
(Continued)
To Remove the Unit from the vehicle's dashboard
Insert each Removal Tool i and pull.
i Removal Tool
(U-shaped)
Note: Do not lose Removal Tools. They will be needed to remove the unit from the vehicle's dashboard.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Electrical Connections
Cautions:
• This wiring information is for experienced technical individual, for safety reason, please your dealer wire this
connection.
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and
keep cable terminals free from touching any metal parts.
• Remember, if your vehicle has a drive computer or a navigation computer, the data of its memory maybe erased
when the battery terminals are disconnected.
❐ Wiring Diagram
Not used
CD changer
10 12 14 16
CD Receiver
CQ-5335U
9
7
11 13 15
5
3
1
8
6
4
2
Antenna
ቪ Antenna Connector
Power Connector
(Rear Side)
Detail of power connector
NO.
1
2
3
4
FUNCTION
BATTERY +12 V
GROUND
NO.
9
10
11
12
13
FUNCTION
REAR SP R (–)
REAR SP R (+)
FRONT SP R (–)
FRONT SP R (+)
FRONT SP L (–)
FRONT SP L (+)
REAR SP L (–)
REAR SP L (+)
※The power connector does not come
along with the unit. If need, please
consult your dealer.
5
6
POWER +12 V ACC 14
7
8
15
16
Accessory Power(ACC)
(+12V DC, negative ground
only)
(Red)
ACC
Ground Lead
(Connect to a clean, bare
metallic part of your vehicle)
(Black)
Ground
Battery
(Yellow)
Battery Lead
(Connect to vehicle battery)
(Violet/Black)
(Gray/Black)
(white)
(Gray)
(Green)
(Violet)
(Green/Black)
(White/Black)
Left Speaker
(Front)
Right Speaker
(Front)
Left Speaker
(Rear)
Right Speaker
(Rear)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
❐ Upgrading the system (connect a CD changer and the wired remote.)
Note:
For wiring, carefully read the operation instructions for the devices connected.
Not used
CQ-5335U
CD changer connector
(10P conncetor)
Wired Remote Connector
(8P connector)
APM/PRG
BAND
DISP
SEEK
MODE
VOL
RC330U
TUNE
DISP UP
PWR SEL
- SAT
Wired Remote
( CA-RC330U, option )
CD Changer (CD-DP880, option)
Extension Cable for connecting the unit and CD changer.
※The Extension cable does not come along with the unit,
if need, please consult your dealer.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Specifications
❐ General
Power Supply:
12 V DC (11 V-16 V) test Voltage 14.4 V, Negative ground
Less than 2.5 A (CD mode, 0.5 W 4-speaker)
37 W × 4 channels at 400 Hz, Volume Control maximum
Current consumption:
Maximum Power Output:
Tone adjustment range:
Bass:
12 dB at 100 Hz
Treble:
12 dB at 10 kHz
Power Output:
18 W per channel into 4 ohms, 40 to 30 000 Hz at 3 % THD
4-8 1
7" × 1-15/16" × 6-1/10" (178 × 50 × 160 mm)
3 lbs. 12 oz (1.7kg)
Suitable Speaker Impedance:
Dimensions (W × H × D):
Weight:
❐ FM Stereo Radio
Frequency Range:
87.9-107.9 MHz
Useable Sensitivity:
12 dBf. (1.1 µV/ 75 1, S/N 30 dB)
17 dBf. (1.8 µV/ 75 1)
30-15 000 Hz 3 dB
75 dB
50 dB Quieting Sensitivity:
Frequency Response:
Alternate Channel Selectivity:
Stereo Separation:
35 dB at 1 kHz
Signal/Noise Ratio:
70 dB (Mono)
❐ AM Radio
Frequency range:
Usable sensitivity:
530 kHz–1 710 kHz
28 dB/µV (25 µV, S/N 20 dB)
❐ Weather Band Radio
Frequency range:
Usable sensitivity:
Signal/Noise Ratio (40 dB/µV):
162.40 –162.55 MHz
3 dB/µV (S/N 20 dB)
50 dB
❐ CD Player
Sampling Frequency:
DA Converter:
Error Correction System:
Pick-Up Type:
32 times over sampling
MASH•1 bit/4 DAC System
Panasonic Super Decoding Algorithm
1-beam
Light Source:
Wavalength:
Semiconductor laser
780 nm
Frequency Response:
Signal to Noise Ratio:
Total Harmonic Distortion:
Wow and Flutter:
20 - 20,000 Hz ( 1 dB)
85 dB
0.01 % (1 kHz)
Below measurable limits
75 dB
Channel Separation:
Above specifications comply with EIA standards.
Note: Specifications and the design are subject to modification without notice due to improvements in technology.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
MEMO
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
MEMO
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CQ-5335U
Download from Www.Somanuals.com. All Manuals Search And Download.
YFM284C482ZA TAMACO0405-0 Printed in Taiwan
Download from Www.Somanuals.com. All Manuals Search And Download.
|