Operating Instructions
<Operations and Settings>
Remote Camera Controller
Model No.
AW-RP120G
How the Operating Instructions are configured
<Basics>:
The <Basics> describes the procedure for connection with the required equipment and for installation.
Before installing this unit, be sure to take the time to read through <Basics> to ensure that the unit will
be installed correctly.
<Operations and Settings> (this manual):
This <Operations and Settings> describes how to operate the unit and how to establish its settings.
RE
MOTE
CAME
RA CONTR
OLL
E
R
AW-RP
120
ENGLISH
VQT4T93A (E)
M0113HO0 -FJ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
How to turn on and off the power of the remote cameras 4
How to turn on the power of the remote cameras . . . . . . . . . . . . . . . . 4
How to turn off the power of the remote cameras . . . . . . . . . . . . . . . . 5
Checking alarm information 40
Displaying alarm information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Returning the unit to the factory default state (INITIALIZE) 41
Making image adjustments for the selected remote camera 6
Setting the gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting the pedestal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting the white balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting the black balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Selecting the color bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the shutter speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the shooting mode (SCENE 1 to SCENE 4) . . . . . . . . . . . . . 10
Setting an ND filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Returning the unit to the factory default state . . . . . . . . . . . . . . . . . . 42
Control interface for external devices 43
Setup Software 45
Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Registering the unit in Setup Software . . . . . . . . . . . . . . . . . . . . . . . 46
Settings for connecting with the remote cameras and switcher . . . . 47
Setting user authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operations of AW‑HE2 51
Table of setting items (dedicated dials and buttons) 52
Table of setting items (menus) 53
Messages 56
Index 58
Operating the osd menu of a remote camera 12
Operating preset memory (PMEM) 13
Registering preset memory (STORE) . . . . . . . . . . . . . . . . . . . . . . . . 14
Recalling preset memory (RECALL) . . . . . . . . . . . . . . . . . . . . . . . . . 14
Deleting preset memory (DELETE). . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the operation items for when preset memory is recalled
(PRESET SCOPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Registering the speed at which to move to the position set in the
preset memory (PRESET SPEED) . . . . . . . . . . . . . . . . . . . . . . . . 15
Operating preset memory groups (PMEM GROUP) 16
Setting the operation mode (SEPARATE/ALL) . . . . . . . . . . . . . . . . . 16
Creating preset memory groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Recalling preset memory groups. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operating tracing memory (TMEM) 18
Registering tracing memory (STORE). . . . . . . . . . . . . . . . . . . . . . . . 18
Recalling tracing memory (RECALL) . . . . . . . . . . . . . . . . . . . . . . . . 19
Deleting tracing memory (DELETE) . . . . . . . . . . . . . . . . . . . . . . . . . 20
Restoring tracing memory (RESTORE). . . . . . . . . . . . . . . . . . . . . . . 20
Setting the items to recall when recalling tracing memory . . . . . . . . 21
Configuring the remote camera operation settings 22
Adjusting the operation speed of the pan, tilt, zoom, and focus . . . . 22
Setting the PAN/TILT lever inclination and speed . . . . . . . . . . . . . . . 22
Setting the pan, tilt, zoom, and focus operation directions . . . . . . . . 23
Setting the minimum lens zoom start speed . . . . . . . . . . . . . . . . . . . 24
Setting the speed of the pan and tilt operations for telephoto
shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting the movement ranges (limiter function) of a remote
camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Returning a remote cameras to its home position. . . . . . . . . . . . . . . 26
Controlling the peripheral devices connected to a remote camera . . 26
Configuring the unit operation settings 27
Enabling or disabling operation with the ENABLE buttons . . . . . . . . 27
Enabling or disabling operation of the ENABLE buttons by menu
operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Enabling or disabling menu operation. . . . . . . . . . . . . . . . . . . . . . . . 28
Switching the focus operation and iris operation. . . . . . . . . . . . . . . . 29
Setting the LCD panel backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Assigning functions to the USER buttons . . . . . . . . . . . . . . . . . . . . . 30
Setting linking with a switcher 31
Registering the camera numbers that will correspond to the image
inputs of the switcher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Enabling or disabling the function for linking with the switcher . . . . . 31
Setting the functions for when the unit is linked with the
switcher 32
BUSCONT function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
FOCUS ASSIST function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CAMERA SELECT view function. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
TALLY IP function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Operating the switcher with the PAN/TILT lever and ZOOM
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
CAM INF function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Memory card operations 36
Initializing a memory card (INIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Saving data to a memory card (SAVE) . . . . . . . . . . . . . . . . . . . . . . . 37
Loading data from a memory card (LOAD) . . . . . . . . . . . . . . . . . . . . 38
Deleting the files saved to a memory card (DELETE). . . . . . . . . . . . 38
Tally settings 39
Registering the camera numbers that will correspond to the tally
inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Setting the sending of tally information from the unit to remote
cameras. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to turn on and off the power of the remote cameras
Turning on the power of the cameras simultaneously
with the turning on of the unit’s power
How to turn on the power of the remote
cameras
1
Set the MENU button to ON
The power of the remote cameras in the standby state can be be turned
on from the unit.
There are the following methods of turning on the power.
z Turning on the power one camera at a time
z Turning on the power of the cameras simultaneously with the turning
on of the unit’s power
z Turning on the power of multiple cameras
Turning off the power of all the cameras
2
Open CAMERA SETUP menu [24]
Turn the F1 dial to display the “2 AUTO ON” item
3
2.AUTO ON
On
Turning off the power of the selected camera group
Each of these methods is described in turn below.
4
Turn the F2 dial to select “On” and press the F2 dial
The power of the remote cameras set to “Serial” or “Network” in
CTRL TYPE menu [36] will now turn on simultaneously with the
turning on of the unit's power.
Turning on the power one camera at a time
1
Select the remote camera
Note
When the corresponding camera selection button
[CAMERA SELECT/GROUP SELECT] is held down for
approximately 3 seconds, the name of the remote camera is
displayed on the top line of the LCD panel and “POWER OFF↓” is
displayed on the bottom line.
z Depending on the number of cameras connected, it may take
some time before you can operate the unit.
2
Turn the F2 dial to select “ON” while keeping the camera
Turning on the power of multiple cameras
selection button held down and then press the F2 dial
1
Set the MENU button to ON
Press the MENU button to turn on its indicator.
CAM100<AW-HE50>
POWER:ON
2
Open CAMERA SETUP menu [24]
2
1
3
Turn the F1 dial to display the “1 CAM POWER” item
1.CAM POWER
GROUP ON
Turning on the power of all the cameras
„
4
Turn the F2 dial to select “ALL ON” and press the F2
dial
1.CAM POWER
ALL ON
Turning on the power of the selected camera group
„
4 Turn the F2 dial to select “GROUP ON” and press the F2
dial
1.CAM POWER
GROUP ON
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to turn on and off the power of the remote cameras (continued)
Turning off the power of multiple cameras
How to turn off the power of the remote
cameras
1
2
3
Set the MENU button to ON
The power of the remote cameras can be be turned off from the unit.
There are the following methods of turning off the power.
z Turning off the power one camera at a time
z Turning off the power of multiple cameras
Turning off the power of all the cameras
Open CAMERA SETUP menu [24]
Turn the F1 dial to display the “1 CAM POWER” item
Turning off the power of the selected camera group
1.CAM POWER
GROUP ON
Each of these methods is described in turn below.
Turning off the power one camera at a time
Turning off the power of all the cameras
„
1
Select the remote camera
When the corresponding camera selection button
[CAMERA SELECT/GROUP SELECT] is held down for
approximately 3 seconds, the name of the remote camera is
displayed on the top line of the LCD panel and “POWER ON↓” is
displayed on the bottom line.
4
Turn the F2 dial to select “ALL OFF” and press the F2
dial
1.CAM POWER
ALL OFF
2
Turn the F2 dial to select “OFF” while keeping the
camera selection button held down and then press the
F2 dial
Turning off the power of the selected camera group
„
4 Turn the F2 dial to select “GROUP OFF” and press the
F2 dial
CAM100<AW-HE50>
POWER:ON
1.CAM POWER
GROUP OFF
2
1
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera
The following settings and adjustments can be made for the selected remote camera directly from this unit.
z Gain
z Pedestal
z R and B gain
z R and B pedestal
z White balance
z Black balance
z Color bar selection
z Detail
z Shutter speed
z Shooting mode selection
The dedicated buttons and dials in the color adjustment section can be used for the gain, pedestal, R and B gain, R and B pedestal, white balance,
black balance, color bar selection, and detail operations.
<Color adjustment section>
BARS button
Color adjustment ENABLE button
AWB button
ABB button
WHITE BAL B button
ATW button
WHITE BAL A button
B GAIN dial
R GAIN dial
GAIN button
DETAIL button
B PED dial
R PED dial
AUTO GAIN button
PED dial
z When the color adjustment ENABLE button indicator is off, operation of the color adjustment section is disabled. Press the button to turn on its
indicator and then perform operation.
z The setting values of the gain, pedestal, R and B gain, R and B pedestal, detail, and shutter speed differ depending on the remote camera connected.
For the setting value ranges of each remote camera, refer to “Table of setting items (menus)” (pages 53 to 54).
z Operation differs as follows when controlling AW-HE60 and AW-HE50.
• During auto iris (when the auto iris button indicator is on), the shutter speed is adjusted automatically. The shutter speed value set from the unit is
not immediately reflected for the camera output images at that time but instead is reflected when manual iris (when the auto iris indicator turns off) is
set.
• While the shooting mode is set to “FullAuto”, the following occurs.
· Auto gain mode is fixed and the gain setting value cannot be changed from “AUTO”.
· ATW mode is fixed and the R and B gain setting values cannot be changed.
· Auto iris is fixed and the shutter speed setting value cannot be changed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera (continued)
Setting the gain
Setting the white balance
In places which are too dark, increase the gain level, and in places
which are too bright, reduce the gain level.
Adjust the ratio between R, G, and B (the three primary colors) so that
white will be reproduced accurately.
When the gain is increased, the noise level also increases.
When the white balance is off, not only will white be reproduced poorly
but the color tone of the entire picture will also deteriorate.
The white balance needs to be set when the lighting conditions and
brightness have changed. The white balance must also be adjusted
when using a remote camera for the first time or when a remote camera
has not been used for a prolonged period of time.
1
Press the GAIN button
The current gain setting appears.
GAIN
:
18dB
The white balance can be adjusted automatically or manually (fine
adjustment after automatic adjustment), and results can be stored in
two memory areas (A and B) of the remote camera. The result in a
memory area can be recalled by pressing the WHITE BAL A button or
WHITE BAL B button on the unit.
In addition, you can select the auto tracking white balance (ATW) mode
for automatically tracking the white balance in accordance with the
lighting conditions.
2
Turn the F1 dial to select a setting
z When the AUTO GAIN button is pressed, auto gain mode is
enabled and the light quantity is adjusted automatically.
z If approximately 3 seconds elapses without the F1 dial being
operated after the GAIN button is pressed, the previous LCD
panel display is redisplayed.
Automatically adjusting the white balance
1
With the selected remote camera, fill the screen with a
white subject (white wall or paper)
Setting the pedestal
z Make sure a shining object or very bright object does not appear
on the screen.
When using multiple cameras, you need to set the same the black level
(pedestal level) for images shot with each camera.
2
Press the WHITE BAL A button to turn on its indicator
1
Turn the PED dial to select a setting
Adjustment in the minus (–) direction makes the parts closer to
black, and adjustment in the plus (+) direction makes the parts
closer to white.
3
Press the AWB button
The AWB button indicator blinks and the white balance is adjusted
automatically.
z The setting value is displayed on the LCD panel during setting.
z When the PED dial is pressed, the setting value does not change
and is only displayed.
When adjustment ends successfully, the button indicator turns off
and the adjustment results are registered to memory A.
When adjustment was not possible, the AWB button indicator blinks
continuously.
Try changing, for example, the lens iris, subject, and lighting
conditions, and then perform adjustment again.
PED
:
+150
4
Press the WHITE BAL B button to turn on its indicator
5
Press the AWB button
Similar to step 3, the adjustment results are saved to memory B.
z When the white balance is adjusted automatically, the R and
B GAIN setting values become “±0”.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera (continued)
Manually adjusting the white balance (R and B gain
Setting the black balance
settings)
The black balance needs to be adjusted when using a remote camera
for the first time or when a remote camera has not been used for a
prolonged period of time. It also needs to be adjusted when significant
changes have occurred in the ambient temperature or at the change of
the seasons.
1
As with the automatic adjustment, fill the screen with a
white subject
When the camera will be used with the same settings and under the
same conditions, the black balance does not need to be adjusted again.
When the black balance is adjusted again, the previous memory data
will be erased and replaced with the new black balance settings.
2
Connect the video output of the currently selected
remote camera to a waveform monitor
3
Press the WHITE BAL A button to turn on its indicator
Automatically adjusting the black balance
4
Turn the R GAIN dial to select the R channel (red)
setting, and turn the B GAIN dial to select the B channel
(blue) setting
The adjustment results are registered to memory A.
z The setting value is displayed during adjustment.
z When the R GAIN dial and B GAIN dial are pressed, the setting
values do not change and are only displayed.
1
Press the ABB button
The ABB button indicator blinks and the black balance is adjusted by
automatically closing the lens iris.
When adjustment ends successfully, the button indicator turns off
and the adjustment results are registered.
When adjustment was not possible, the ABB button indicator blinks
continuously.
z When the black balance is adjusted automatically, the R and
B PED setting values return to “±0”.
R GAIN :
B GAIN :
+150
+150
5
Press the WHITE BAL B button to turn on its indicator
Perform step 4 in the same way as with the WHITE BAL A button to
set memory B.
Manually adjusting the black balance
(R and B pedestal adjustment)
1
Connect the video output of the currently selected
remote camera to a waveform monitor
Auto tracking white adjustment (ATW)
You can select the auto tracking white balance (ATW) mode for
automatically tracking the white balance in accordance with the lighting
conditions.
2
3
4
Press the auto iris button to turn its indicator off
Turn the IRIS dial to close the lens iris
1
Press the ATW button to turn on its indicator
ATW mode is enabled.
Turn the R PED dial to select the R channel (red) setting,
and turn the B PED dial to select the B channel (blue)
setting
z The setting value is displayed during adjustment.
z When the R PED dial and B PED dial are pressed, the setting
values do not change and are only displayed.
z If there is no white on the screen, it may not be possible to
compensate the white balance properly.
Also, it may not be possible to compensate the white balance
properly depending on the lighting conditions.
R PED :
B PED :
+150
+150
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera (continued)
Selecting the color bars
Adjusting the shutter speed
Press the BARS button to output color bar signals from the remote
camera.
The shutter mode and shutter speed of a remote camera can be
selected.
1
Press the MENU button to turn on its indicator
Button indicator on : Outputs the color bar signal
Button indicator off : Outputs the signal for the images shot by
the camera
2
Open SHUTTER menu [21]
Setting the shutter mode
3
Turn the F1 dial to display the “1 SHUTTER” item
Setting the detail
1.SHUTTER
Off
The image detail (image sharpness) can be adjusted.
1
Press the DETAIL button
The current detail setting appears.
4
Turn the F2 dial to select the shutter mode, and then
press the F2 dial to confirm the selection
DETAIL :
LEVEL :
On
LOW
F1 dial
F2 dial
Off
Step
: Turns off the electronic shutter.
: Operates the shutter at the shutter speed set in the
“2. SPEED” item.
Synchro : Operates the shutter at the shutter speed set for the
remote camera.
2
Turn the F1 dial and F2 dial to select settings
Set the shutter speed value for synchro mode in the
OSD menu of the remote camera.
For details, refer to the operating instructions for the
remote camera.
ELC
: Controls the electronic shutter and automatically adjusts
the light quantity.
z The shutter mode settings differ depending on the remote camera
connected. Check the operating instructions for the corresponding
model.
Setting the shutter speed
When “Step” has been selected as the shutter mode, you can specify
the shutter speed.
5 Turn the F1 dial to display the “2 SPEED” item
2.SPEED
1/100
6 Turn the F2 dial to adjust the shutter speed
z The shutter speed settings differ depending on the remote camera
connected. Check the operating instructions for the corresponding
model.
Note
z For a remote camera connected via a serial connection, when
you change the camera group once and then return to the original
camera group, the shutter speed is set to “1/100”.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera (continued)
Setting the shooting mode (SCENE 1 to SCENE 4)
Change the shooting mode (scene file) of the remote camera to match the shooting conditions.
Use the SCENE 1 to SCENE 4 buttons to change the shooting mode.
SCENE 3 button
SHIFT button
SCENE 1 button
SCENE 2 button
SCENE 4 button
1
Press the SHIFT button to turn on its indicator
2
Press one of the SCENE 1 to SCENE 4 buttons
The indicator of the selected button turns on and the shooting mode changes.
z The names of shooting modes and operation of each mode differ depending on the model of remote camera. For details, refer to the operating
instructions for the remote camera.
The following shows the relationship between the SCENE 1 to SCENE 4 buttons on the unit and the shooting modes of the remote camera.
Remote camera shooting mode
AW‑HE870
AW‑E860
AW‑E750
AW‑E650
AW‑E350
Button on unit
AW‑HE60
AW‑HE50
AK‑HC1500
AK‑HC1800
AW‑HE120
AW‑HE100
SCENE 1
SCENE 2
SCENE 3
SCENE 4
Scene1
Scene2
Scene3
Scene4
FullAuto
Manual1
Manual2
Manual3
CURRENT
PRESET
USER1
Halogen
Fluorescent
Daylight
User
Halogen
Fluorescent
Outdoor
User
USER2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Making image adjustments for the selected remote camera (continued)
Selecting an ND filter with the USER buttons (USER 1
to USER 8)
Setting an ND filter
The ND filter setting can be configured when the selected remote
camera uses a lens with an ND filter function.
The ND filter settings “ND1” to “ND4” can be assigned to the USER
buttons (USER 1 to USER 8) to enable selection with the buttons.
⇒“Assigning functions to the USER buttons” (page 30)
1
Press the MENU button to turn on its indicator
1
Press one of the USER buttons (USER 1 to USER 8)
The indicator of the selected button turns on and the corresponding
ND filter is applied.
2
Open ND FILTER menu [22]
1.ND FILTER
ND1
z When AW-HE870, AW-E860, AW-E750, AW-E650, or AW-E350 is
connected:
The ND filter of the remote camera can be turned Off and On with
the USER button on the unit that has ND1 assigned.
3
Turn the F2 dial to select a setting, and then press the
F2 dial to confirm the selection
The settings displayed when you turn the F2 dial differ depending on
the model of remote camera connected.
The following shows the menu display on the unit and the setting
values of the remote cameras.
Remote camera setting values
AW‑HE50
Menu display
on the unit
AK‑HC1500
AK‑HC1800
AW‑HE60
AW‑HE100
(*1)
AW‑HE120
ND1
ND2
ND3
ND4
Through
1/4
Clear
1/4
―
―
―
―
1/16
1/16
1/64
1/64
(*1) “ND2↓”, “ND3↓”, and “ND4↓” can be displayed by turning the F2
dial but a selection cannot be confirmed by pressing the dial.
Remote camera setting values
AW‑HE870
Menu display
on the unit
AW‑E860
AW‑E750
AW‑E650
AW‑E350
Off
On
Off
On
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the osd menu of a remote camera
To set the advanced settings of a remote camera, operate the menu superimposed on the image output of the remote camera (this menu is referred to
as the OSD menu in this manual). The OSD menu of a connected remote camera can be operated from the unit.
CAMERA OSD button
EXIT button
F1 dial
F2 dial
1
Hold down the CAMERA OSD button to turn on its indicator
The OSD menu appears on the selected remote camera and becomes able to be operated from the unit.
2
Operate the OSD menu
Use the F1 dial, F2 dial, and EXIT button to operate the OSD menu.
Operation differs depending on the model connected.
<Table of operations>
Remote camera
AW-HE50
AW-HE60
AW-HE120
Dial/button operation
Turn the F1 dial.
OSD menu operation
z Moves the items (*1)
z Selects a setting (*2)
.
.
Press the F1 dial.
Confirms the change to the selected setting.
Cancels the selected setting.
Press the EXIT button.
z Moves the items (*1)
z Selects a setting (*3)
.
.
Turn the F1 dial.
AK-HC1500
AK-HC1800
AW-HE870
Press the F1 dial.
Press the EXIT button.
Turn the F1 dial.
Confirms the change to the selected setting.
Cancels the selected setting.
Moves the items (*1)
.
AW-E350
AW-E650
AW-E750
AW-E860
AW-HE100
Press the F1 dial.
Confirms the sub-menu selection.
z Changes the setting directly (*4)
z Confirms the sub-menu selection.
Turn the F2 dial.
(*1) Turn clockwise
Turn counterclockwise
(*2) Turn clockwise
Turn counterclockwise
(*3) Turn clockwise
Turn counterclockwise
: Moves the items up.
: Moves the items down.
: Changes the setting in the plus (+) direction.
: Changes the setting in the minus (–) direction.
: Changes the setting in the minus (–) direction.
: Changes the setting in the plus (+) direction.
(*4) Turning the dial changes the setting and instantaneously reflects the new value on the remote camera.
Turn clockwise
Turn counterclockwise
: Changes the setting in the plus (+) direction and confirms the value.
: Changes the setting in the minus (–) direction and confirms the value.
3
Hold down the CAMERA OSD button to turn off its indicator
The menus of the unit become able to be operated.
Notes
z When the unit is operating the OSD menu of a remote camera, the CAMERA OSD button lighting state and OSD menu display state may no
longer match and OSD menu operation may not be able to be performed properly if the OSD menu OFF operation is performed for the same
remote camera from, for example, another remote camera controller or a wireless remote controller.
In such a case, hold down the CAMERA OSD button on the unit, and after the CAMERA OSD button lighting state (off) and OSD menu display
state (OSD menu hidden) match, hold down the CAMERA OSD button again and then perform the operation.
z If a camera selection button [CAMERA SELECT/GROUP SELECT] is pressed to switch to another remote camera to control from the unit during
the display of the OSD menu of a remote camera, the OSD menu of the remote camera that was selected disappears.
z For details on the menu items that are displayed, check the operating instructions for the corresponding model.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating preset memory (PMEM)
z Changing pages
The preset memory of a remote camera can be operated from the unit.
The following settings that you have adjusted in advance can be stored
in preset memory.
Press one of the number buttons [1] to [50] to directly select any of the
50 preset memory.
Furthermore, pressing the PMEM PAGE button to change pages allows
you to operate up to 100 preset memory for each camera.
z Pan/tilt positions
z Zoom positions
z Focus positions
z Lens iris settings (manual iris only)
z White balance settings
Button indicator on
Button indicator on
Press the PMEM
PAGE button
Notes
z If the MEM ENABLE button indicator is off, preset memory
operation is not possible. Press the button to turn on its indicator
and then perform operation.
z Preset numbers PMEM 1 to 10 are also used as start positions
when recalling tracing memory. Preset data may be overwritten or
deleted by tracing memory operation.
Page 1 selected
Page 2 selected
z The number of preset memory and data that can be registered
differ depending on the remote camera.
For details, check the operating instructions for the corresponding
model.
<Preset numbers and registered pages>
Preset number
PMEM 1 to PMEM 50
PMEM 51 to PMEM 100
Page number Number button
Page 1
[1] to [50]
Page 2
MEM SETTING button
MEM ENABLE button
MEM DELETE button
Example: When specifying preset number “PMEM 51”
1. Press the PMEM page button to select Page 2.
2. Press number button [1].
PMEM button
MEM STORE button
PMEM PAGE
indicators
z Lighting of number button indicators
PMEM PAGE
button
The lighting method of the number buttons differs depending on the
remote camera or pan-tilt head that the unit is controlling.
<Lighting method of number button indicators>
Remote cameras and
pan‑tilt heads
Lighting method of number button
indicators
AW-HE50, AW-HE60,
AW-HE120
The indicators of the number buttons with
preset memory registered turn on.
Number buttons
[1] to [50]
AW-HE100, AW-PH360,
AW-PH405, AW-PH650,
AW-PH400
The indicator of the number button that
was last pressed turns on.
However, when preset memory is deleted
in DELETE mode, all of the number
buttons turn off.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating preset memory (PMEM) (continued)
Registering preset memory (STORE)
Recalling preset memory (RECALL)
1
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
2
3
4
5
2
Output the images to be shot to the monitor
Press the PMEM button to turn on its indicator
Press the MEM STORE button to turn on its indicator
Press the PMEM button to turn on its indicator
3
Hold down a number button to specify the preset
number to recall
The registered settings are recalled.
z When the indicator of the MEM STORE button or MEM DELETE
button is on, preset memory is not recalled when a number button
is pressed.
Press the PMEM button or press the MEM STORE button or
MEM DELETE button with the indicator turned on to turn off its
indicator, and then perform the operation.
Operate the PAN/TILT lever and ZOOM button to
determine the camera angle to register
If necessary, adjust the focus and iris as well.
6
Hold down a number button to specify the preset
number to register
“STORE COMPLETE” appears on the second line of the LCD panel.
The current camera positions and settings are registered to the
preset memory of the remote camera.
Deleting preset memory (DELETE)
z To continue registering different camera angles to a preset
memory belonging to the same “page number”, repeat steps 5 to
6.
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
Notes
z When registering preset data, hold down the number button.
z If a number button that already has preset memory registered
is held down, the saved data will be deleted as it will be
overwritten.
2
3
4
Press the PMEM button to turn on its indicator
Press the MEM DELETE button to turn on its indicator
Hold down a number button to specify the preset
number to delete
“DELETE COMPLETE” appears on the second line of the LCD panel
and the registered settings are deleted.
Notes
z When deleting preset data, hold down the number button.
z When the preset number used with tracing memory is held
down, the tracing data is also deleted at the same time.
⇒ For details on tracing memory, refer to “Operating tracing
memory (TMEM)” (page 18).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating preset memory (PMEM) (continued)
Setting the operation items for when preset
memory is recalled (PRESET SCOPE)
Registering the speed at which to move
to the position set in the preset memory
(PRESET SPEED)
You can select whether to recall all or only some of the settings
registered to preset memory.
The unit registers the speed (PRESET SPEED) at which to move to the
set position when preset memory is recalled to each preset number.
When a preset is recalled, the unit sets PRESET SPEED on the remote
camera and the remote camera moves to the preset position at the
speed set for PRESET SPEED.
Note
z This function is enabled when AW-HE50, AW-HE60, or
AW-HE120 is selected.
Performing operation at a different speed for each preset memory
enables video to be played at a variety of speeds.
Notes
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
z The movement speed registered in the procedure below is
registered to the corresponding camera number, and is not
registered to the preset memory of the remote camera. Therefore,
if the preset memory is recalled from a controller other than this
unit on which the movement speed was registered, movement
will be at a different speed even in the case of the same preset
number.
2
Press the PMEM button to turn on its indicator
z When the connection type or connection destination IP address
is changed with CTRL TYPE menu [36], AUTO IP menu [37], or
SWAP IP menu [38], PRESET SPEED set for the corresponding
camera number is initialized.
3
Press the MEM SETTING button to turn on its indicator
The setting of the selected remote camera is displayed.
SPEED :
30
SCOPE : MODE A
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
4
Turn the F2 dial to select a setting for the “SCOPE” item
from MODE A to MODE C, and then press the F2 dial to
confirm the selection
The setting of the remote camera is changed.
This is applied the next time the preset is recalled.
2
3
4
Press the PMEM button to turn on its indicator
<SCOPE settings and recalled items>
Recalled item
Press the MEM STORE button to turn on its indicator
White balance
adjustment
value
Setting
Pan, tilt, zoom,
and focus
Iris
Press the MEM SETTING button to turn on its indicator
The setting of the selected remote camera is displayed.
MODE A
MODE B
MODE C
√
√
√
√
√
√
SPEED :
SCOPE : MODE A
30
—
—
—
√: Recalled —: Not recalled
5
Turn the F1 dial to select the setting of the “SPEED”
item, and then press the F1 dial to confirm the selection
The following shows the relationship between the set value and the
speed at which the remote camera moves to the set position when
preset memory is recalled.
Note
z MODE A to MODE C are not registered to the remote camera
preset memory or the unit. The settings become the common
settings for when preset memory is recalled, and the same
settings are applied regardless of which preset number is
selected.
1
30
Slow
Fast
6
Hold down a number button to specify the preset
number to register
The current remote camera settings are registered to preset
memory, and PRESET SPEED is registered to the unit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating preset memory groups (PMEM GROUP)
The unit allows you register up to four “preset memory groups” created
Creating preset memory groups
by selecting one preset memory for each of multiple remote cameras.
Pressing any of the PM GRP 1 to PM GRP 4 buttons simultaneously
recalls all preset memory registered to the corresponding preset
memory group.
Registering the preset memory to recall when in
SEPARATE mode
The following setting procedures use the example of setting PMEM
GROUP1 but the setting procedures are the same for PMEM GROUP2
to PMEM GROUP4.
1
Press the MENU button to turn on its indicator
Open the following menus and configure the settings.
<Preset memory groups and menu numbers>
2
3
4
Open PM GRP1 menu [31]
Preset memory group
Menu
1.PM GRP1 MODE
SEPARATE
PMEM GROUP1
PMEM GROUP2
PMEM GROUP3
PMEM GROUP4
PM GRP1 menu [31]
PM GRP2 menu [32]
PM GRP3 menu [33]
PM GRP4 menu [34]
Turn the F1 dial to display the “2 PM GRP1 1/10” item
2.PM GRP1 1/10
NoAsgn ——————
Setting the operation mode (SEPARATE/
ALL)
Turn the F2 dial to set the camera number and preset
number to register to PMEM GROUP1
If you turn the F2 dial to select the camera number and then press
the F2 dial to confirm the selection, you will then be able to select
the preset number.
1
Press the MENU button to turn on its indicator
Set the preset number in the same way as the camera number.
2
Open PM GRP1 menu [31]
2.PM GRP1 1/10
CAM001 PRE001
1.PM GRP1 MODE
SEPARATE
Camera number Preset number
Camera number : Select from NoAsgn and CAM001 to CAM100.
When “NoAsgn” is set, preset memory is not
registered.
3
Turn the F1 dial to display the “1 PM GRP1 MODE” item
Preset number : Select from PRE001 to PRE100.
4
Turn the F2 dial to select the operation mode, and then
press the F2 dial to confirm the selection
OFF
: Disables group creation.
Even if you press any of the PM GRP1 to PM GRP4
buttons, a preset memory group will not be recalled.
5
Turn the F1 dial to display the “3 PM GRP1 2/10” to
“11 PM GRP1 10/10” items
SEPARATE : Allows you to create a group by selecting a different
preset number from each remote camera.
Up to ten preset numbers can be registered to one
group.
6
Register the camera numbers and preset numbers
z Configure the settings in the same way as step 4.
z Up to ten preset memory can be registered to one group.
ALL
: Allows you to create a group by selecting the same
preset number from each remote camera.
One preset number for each of all the remote
cameras registered to the unit can be registered to
one group.
Note
z Do not set the same camera number two or more times for one
preset memory group.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating preset memory groups (PMEM GROUP) (continued)
Registering the preset memory to recall when in ALL
Recalling preset memory groups
mode
1
Press the MENU button to turn on its indicator
Pressing a button to recall a preset memory group
Use PM GRP 1 to PM GRP 4 to recall preset memory groups.
2
3
4
Open PM GRP1 menu [31]
PM GRP 1 to PM GRP 4 buttons
USER ENABLE button
1.PM GRP1 MODE
ALL
Turn the F1 dial to display the “12 PM GRP1 ALL” item
12.PM GRP1 ALL
PRE001
SHIFT button
1
Press the SHIFT button to turn on its indicator
Turn the F2 dial to select a preset number, and then
press the F2 dial to confirm the selection
2
Press the PM GRP 1 button
When the operation mode of PMEM GROUP1 is “SEPARATE”:
Simultaneously recalls each remote camera preset memory
registered to the “2. PM GRP1 1/10” to “11. PM GRP1 10/10”
items.
When the operation mode of PMEM GROUP1 is “ALL”:
The preset memory registered in the “12. PM GRP1 ALL” item is
recalled for all of the remote cameras registered to the unit.
z Preset memory is not recalled for a remote camera for which
“NoAsign” is set in CTRL TYPE menu [36].
Note
z If the USER ENABLE button indicator is off, operation of the
PM GRP 1 to PM GRP 4 buttons is not possible. Perform
operation while the button indicator is on.
Recalling a preset memory group by GPI input
A preset memory group can be recalled by contact input of the TALLY/
GPI connector on the rear panel of the unit.
<PIN numbers and preset memory groups>
Signal
Pin number
Corresponding preset memory group
name
19
7
GPI IN 1
GPI IN 2
GPI IN 3
GPI IN 4
PMEM GROUP 1
PMEM GROUP 2
PMEM GROUP 3
PMEM GROUP 4
20
8
⇒“Control interface for external devices” (page 43)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating tracing memory (TMEM)
The unit incorporates tracing memory (TMEM) for recording a series of
operations that were performed for a connected remote camera.
This feature allows you to duplicate the recorded operations of a remote
camera.
Registering tracing memory (STORE)
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
<Tracing memory>
Recording target Camera numbers CAM1 to CAM10
Functions that
can be recorded
Pan, tilt, zoom, focus, iris, and white balance
mode
2
Output the images to be shot to the monitor
Recording time
Up to 5 minutes per camera
Up to 10 per camera
Number of
recording
memory
3
Press the TMEM button to turn on its indicator
The tracing memory status appears.
The indicators of number buttons with registered tracing memory
turn on.
Record buttons
Number buttons [1] to [10]
Selected camera number
Notes
CAM1 TMEM
3m50s Remained.
z If the MEM ENABLE button indicator is off, tracing memory
operation is not possible. Perform operation while the button
indicator is on.
z Preset numbers PMEM 1 to 10 of the preset memory are used
as start positions at the time of recalling tracing memory so they
are overwritten when the tracing memory registration operation is
performed.
z The last point when tracing memory is recalled may not match
that at the time of recording because of the error of movement of
the remote camera.
Remaining possible recording time (max 5 m 00 s)
Note
z A button with no tracing memory registered does not turn on
even when it is a button with preset memory registered.
Taking precautions such as the following can help reduce the
error.
• Use the lens zoom at the WIDE side (wide-angle end).
• Perform pan, tilt, zoom, and focus operations slowly.
• Set a short recording time.
4
Press the MEM STORE button to turn on its indicator
Execute tracing memory recalling several times to sufficiently
check the operation of the camera before you begin operation.
5
Operate the PAN/TILT lever and ZOOM button to
determine the camera angle to register
If necessary, adjust the focus, iris, and white balance as well.
<Tracing memory operation section>
TMEM button
6
Hold down one of the number buttons [1] to [10] that
has its indicator turned off to specify the tracing
memory number
The current camera position and settings are registered to the preset
memory of the remote camera, and become the start position and
settings at the time of recalling.
MEM DELETE button
MEM STORE button
RESTORE button
MEM ENABLE button
The indicators of the number button that was held down and START
button [11] blink. (Recording standby state)
z If an operation that is target for recording such as moving the PAN/
TILT lever is performed at that time, the recording standby state is
cancelled and the status returns to that of step 3.
Tracing memory number
TM05:
Standby Store.
Notes
START button [11]
Number buttons [1] to [10]
z If you want to register tracing memory to a button whose
indicator is on, delete the registered tracing memory and then
register the new tracing memory.
STOP button [12] MEM SETTING button
z If a number button that already has preset memory registered
is held down, the saved preset memory will be deleted as it
will be overwritten.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating tracing memory (TMEM) (continued)
7
Press START button [11]
The indicator of START button [11] turns on. (Operation wait state)
Recalling tracing memory (RECALL)
TM05:
Waiting Opr.
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
8
Operate one of the PAN/TILT lever, ZOOM button,
FOCUS dial, IRIS dial, and white balance mode selection
buttons
2
Press the TMEM button to turn on its indicator
The tracing memory status appears.
The indicators of number buttons with registered tracing memory
turn on.
The recording of tracing memory starts from the point in time that the
operation began.
z To record the focus operation and iris operation, press the focus
button and auto iris button to turn off their indicators and then
perform the operations.
Selected camera number
CAM1 TMEM
3m50s Remained.
Recording time
Remaining possible recording time (max 5 m 00 s)
TM05:0m02s
Storing.
Note
z A button with no tracing memory registered does not turn on
even when it is a button with preset memory registered.
9
Press STOP button [12]
Recording stops and the tracing memory is saved.
The registered number button turns on and the status returns to that
of step 3.
z When the possible recording time elapses, recording stops
automatically.
3
Press one of the number buttons that has its indicator
turned on to specify the tracing memory number
The remote camera moves to the start position.
The indicators of the number button that was pressed and START
button [11] blink. (Recall standby state)
At that time, operations up until the point in time that recording
stops are recorded.
TM03:0m00s
/0m59s
Standby Recall.
4
Press START button [11]
The tracing memory is recalled and the remote camera starts
moving.
The indicator of START button [11] turns on.
Total time of tracing
memory during recalling
Current recall
Tracing memory number
position
TM03:0m20s
Recalling.
/0m59s
5
When the recording time elapses, the remote camera
stops automatically
The number button that was blinking turns on, the indicator of
START button [11] turns off, and the process returns to step 2.
z When STOP button [12] is pressed during recalling, recalling stops
and the process returns to step 2.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating tracing memory (TMEM) (continued)
Deleting tracing memory (DELETE)
Restoring tracing memory (RESTORE)
1
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be operated
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select the
remote camera to be controlled from the unit
2
2
Press the TMEM button to turn on its indicator
The tracing memory status appears.
Output the images to be shot to the monitor
The indicators of number buttons with registered tracing memory
turn on.
3
Press the TMEM button to turn on its indicator
The tracing memory status appears.
The indicators of number buttons with registered tracing memory
turn on.
Selected camera number
CAM1 TMEM
3m50s Remained.
Selected camera number
CAM1 TMEM
Remaining possible recording time (max 5 m 00 s)
3m50s Remained.
Note
Remaining possible recording time (max 5 m 00 s)
z A button with no tracing memory registered does not turn on
even when it is a button with preset memory registered.
Note
z A button with no tracing memory registered does not turn on
even when it is a button with preset memory registered.
3
Press the MEM DELETE button to turn on its indicator
4
Hold down one of the number buttons [1] to [10] that
has its indicator turned on to specify the tracing
memory number
4
Press the RESTORE button to turn on its indicator
The registered preset memory and tracing memory are deleted.
5
Press one of the number buttons [1] to [10] that has its
indicator turned on
The remote camera moves to the start position.
The indicators of the number button that was pressed and START
button [11] blink. (Restore standby state)
z At this time, you can operate the PAN/TILT lever to change the
start position.
TM03:0m00s
/0m50s
Standby Restore.
6
Press START button [11]
The tracing memory is recalled and the remote camera starts
moving.
Total time of tracing memory
during recalling
Current recall position
TM03:0m20s
Restoring.
/0m50s
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating tracing memory (TMEM) (continued)
7
Operate one of the PAN/TILT lever, ZOOM button,
FOCUS dial, IRIS dial, and white balance mode selection
buttons to make a correction
Setting the items to recall when recalling
tracing memory
Only the data for which the operation was performed is overwritten
from the point in time that correction operation was performed.
You can select whether to recall all or only some of the items registered
to tracing memory.
Note
1
Press the MEM SETTING button to turn on its indicator
The current setting appears.
z Tracing data cannot be partially restored.
After starting the tracing data restore operation, be sure to
perform the operation all the way to the end.
SPEED :
———
SCOPE : MODE A
8
When the recording time elapses, the remote camera
stops automatically
2
Turn the F2 dial to select a setting for the “SCOPE” item
from MODE A to MODE C, and then press the F2 dial to
confirm the selection
The process returns to step 3.
z When STOP button [12] is pressed during recalling, recalling
stops.
z The setting of the unit is changed.
This is is applied the next time the tracing data is recalled.
The total time of the tracing memory changes, and the process
returns to step 3.
<SCOPE settings and recalled items>
Recalled item
Setting
Pan, tilt, zoom,
and focus
White balance
mode
Iris
MODE A
MODE B
MODE C
√
√
√
√
√
√
—
—
—
√: Recalled —: Not recalled
When the operation is performed, the PRESET SCOPE setting of
the remote camera is changed to the same setting as well at the
same time.
⇒“Setting the operation items for when preset memory is recalled
(PRESET SCOPE)” (page 15)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the remote camera operation settings
Adjusting the operation speed of the pan,
tilt, zoom, and focus
Setting the PAN/TILT lever inclination and
speed
The dedicated dials can be used to individually adjust the operation
speed of the remote camera for each of the PAN/TILT lever, ZOOM
button, and FOCUS dial operations performed with the unit.
The correlation between the angle and operating speed when the PAN/
TILT lever is inclined can be adjusted.
1
2
3
Press the MENU button
ZOOM SPEED dial
Open RP SETUP menu [25]
Turn the F1 dial to display the “2 P/T CURV” item
2.P/T CURV
1
4
Turn the F2 dial to select a setting, and then press the
F2 dial to confirm the selection
z The higher the value selected, the slower the operation when the
lever begins to be moved.
FOCUS SPEED dial
PAN/TILT SPEED dial
Operating speed
Operation of SPEED dial
„
Turned clockwise
Turned counterclockwise : Operation is at a lower speed (LOW)
: Operation is at a higher speed (HI)
P/T CURV=1
P/T CURV=5
Angle of lever
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the remote camera operation settings (continued)
Setting the tilting direction
Setting the pan, tilt, zoom, and focus
operation directions
Set the operation of the remote camera in the vertical direction in
response to forward and backward operation of the PAN/TILT lever.
You can set the direction that a remote camera moves in response to
the operation of the PAN/TILT lever, ZOOM button, and FOCUS dial.
With this unit, you can set the direction for each camera number.
1
2
3
Press the MENU button
Open TILT DIRECTION menu [27]
Setting the panning direction
Turn the F1 dial to display the camera number for which
Set the operation of the remote camera in the horizontal direction in
response to the horizontal operation of the PAN/TILT lever.
to configure the setting
1.CAM1
NORMAL
1
2
3
Press the MENU button
Open PAN DIRECTION menu [26]
4
Turn the F2 dial to select “NORMAL” or “REVERSE”,
and then press the F2 dial to confirm the selection
Turn the F1 dial to display the camera number for which
to configure the setting
NORMAL : The remote camera moves upward when the PAN/
TILT lever is moved away from you, and downward
when the lever is moved toward you.
1.CAM1
NORMAL
REVERSE : Operation is in the opposite direction to NORMAL.
4
Turn the F2 dial to select “NORMAL” or “REVERSE”,
and then press the F2 dial to confirm the selection
Setting the zooming direction
NORMAL : The remote camera moves to the left when the PAN/
TILT lever is moved toward the left, and to the right
Set the zooming operation of the lens in response to the operation of the
ZOOM button.
when the lever is moved toward the right.
REVERSE : Operation is in the opposite direction to NORMAL.
1
2
3
Press the MENU button
Open ZOOM DIRECTION menu [28]
Turn the F1 dial to display the camera number for which
to configure the setting
1.CAM1
NORMAL
4
Turn the F2 dial to select “NORMAL” or “REVERSE”,
and then press the F2 dial to confirm the selection
NORMAL : The lens zooms toward the telephoto end when
the TELE side of the ZOOM button is pressed, and
toward the wide-angle end when the WIDE side is
pressed.
REVERSE : Operation is in the opposite direction to NORMAL.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the remote camera operation settings (continued)
Setting the focusing direction
Setting the minimum lens zoom start speed
Set the focusing operation of the lens in response to the operation of the
FOCUS dial.
Correct the zoom control amount to send from the unit so that the lens
zoom starts to move smoothly when the zoom button is pressed in
slowly.
1
2
3
Press the MENU button
1
2
3
Press the MENU button
Open FOCUS DIRECTION menu [29]
Open PTZ ADJUST menu [30]
Turn the F1 dial to display the camera number for which
to configure the setting
Turn the F1 dial to display the “1 Z MIN SPEED” item
1.CAM1
NORMAL
1.Z MIN SPEED
Off
4
4
Turn the F2 dial to select “NORMAL” or “REVERSE”,
and then press the F2 dial to confirm the selection
Turn the F2 dial to select the correction amount, and
then press the F2 dial to confirm the selection
z The lowest correction amount is “1”, and the highest is “8”.
No correction is made with the “Off” setting.
While observing the images on a monitor, press the ZOOM button
slowly and check whether the lens zoom starts moving smoothly.
NORMAL : The focus moves toward the far end when the
FOCUS dial is turned clockwise, and toward the near
end when the dial is turned counterclockwise.
REVERSE : Operation is in the opposite direction to NORMAL.
Setting the speed of the pan and tilt
operations for telephoto shooting
During telephoto shooting, the remote camera’s pan and tilt operations
are slowed down to make positioning easier.
1
2
3
Press the MENU button
Open PTZ ADJUST menu [30]
Turn the F1 dial to display the “2 SPEED WITH Z” item
2.SPEED WITH Z
Off
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
On : The pan and tilt operations during telephoto shooting are
slow.
Off : Movement is at normal speed.
Note
z This function is enabled when AW-HE50, AW-HE60, or
AW-HE120 is connected.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the remote camera operation settings (continued)
When other remote camera
„
Setting the movement ranges (limiter
function) of a remote camera
4 Press the F2 dial to confirm the setting
The position in the up direction of the currently selected remote
camera is set as the up limit and the limiter is enabled.
(The setting is stored in the remote camera.)
Depending on the installation location, there may be an obstruction in
a movement range of a remote camera, and the remote camera may
come into contact with that obstruction when the pan or tilt operation is
performed.
A malfunction or accident may occur if the remote camera comes into
contact with the obstruction so you need to set a limiter in front of the
obstruction to prevent contact.
3.LIMIT UP
EXEC
Press the F2 dial
Also set a limiter if there is a subject you do not wish to shoot in a
movement range.
3.LIMIT UP
LIMIT ON
From the unit, you can configure the remote camera limiter setting for
the direction of each of the up, down, left, and right limits.
z If the F2 dial is turned or the F1 dial is turned to display another
item and then the “3. LIMIT UP” item is redisplayed, “EXEC↓”
reappears on the second line of the LCD panel.
If the F2 dial is pressed at this time, “LIMIT OFF” is displayed and
the limiter is cancelled.
Setting procedure
1
2
3
Press the MENU button
5
Turn the F1 dial to display the “4 LIMIT DOWN”,
“5 LIMIT LEFT”, or “6 LIMIT RIGHT” item
Perform the same operation as step 4 to set the down limit, left limit,
and right limit.
Open PTZ ADJUST menu [30]
Menu item
LIMIT UP
Setting target
Up limit
Turn the F1 dial to display the “3 LIMIT UP” item
LIMIT DOWN
LIMIT LEFT
LIMIT RIGHT
Down limit
Left limit
When AW‑HE50, AW‑HE60, or AW‑HE120:
„
Right limit
4
Turn the F2 dial to select “On”, and then press the F2
dial to confirm the selection
The position in the up direction of the currently selected remote
camera is set as the up limit and the limiter is enabled.
(The setting is stored in the remote camera.)
3.LIMIT UP
Off
Turn the F2 dial
3.LIMIT UP
On
Press the F2 dial
3.LIMIT UP
On
z Turning the F2 dial to display “Off↓” and then pressing the F2 dial
to confirm the selection cancels the limiter.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the remote camera operation settings (continued)
Returning a remote cameras to its home
position
Controlling the peripheral devices
connected to a remote camera
Position the remote camera in the vertical and horizontal directions so
that its shooting direction becomes forward (home position).
The peripheral devices connected to a remote camera can be controlled.
Control the devices with FUNCTION menu [23].
1
Press the MENU button
Note
z The position stored as the home position on the remote camera
cannot be changed.
2
Open FUNCTION menu [23]
1
2
3
Press the MENU button
Controlling a defroster
Open CAMERA SETUP menu [24]
When the selected remote camera is equipped with a defroster function
(AW-PH650 + camera), the defroster can be controlled.
Turn the F1 dial to display the “4 HOME POSITION”
item
3 Turn the F1 dial to display the “2 DEFROSTER” item
4.HOME POSITION
SET
4 Turn the F2 dial to select “Off” or “On”, and then press
the F2 dial to confirm the selection
2.DEFROSTER
Off
4
Press the F2 dial
The remote camera moves to its home position.
Controlling a wiper
When the selected remote camera is equipped with a wiper function
(AW-PH650 + camera), the wiper can be controlled.
3 Turn the F1 dial to display the “3 WIPER” item
4 Turn the F2 dial to select “Off” or “On”, and then press
the F2 dial to confirm the selection
3.WIPER
Off
Controlling a heater or fan
When the selected remote camera is equipped with a heater or fan
function (AW-PH650 + camera), the heater or fan can be controlled.
3 Turn the F1 dial to display the “4 HEATER/FAN” item
4 Turn the F2 dial to select “Off” or “On”, and then press
the F2 dial to confirm the selection
4.HEATER/FAN
Off
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the unit operation settings
Enabling or disabling operation with the ENABLE buttons
The unit has five ENABLE buttons.
Each of the ENABLE buttons can be used to independently enable or disable the corresponding operation shown below.
Color adjustment ENABLE button
MEM ENABLE button
USER ENABLE button
z Operation of color adjustment section
z Operation of memory (preset memory and tracing memory)
z Operation of USER buttons
FOCUS/ZOOM/IRIS ENABLE button
PAN/TILT ENABLE button
z Operation of FOCUS dial, ZOOM button, and IRIS dial
z Operation of PAN/TILT lever
1
Press the ENABLE button
The button indicator lighting state changes.
Button indicator on or blinking : Operation of the corresponding functions are enabled.
Button indicator off : Operation of the corresponding functions are disabled.
z Menu operation is possible even when the MEM ENABLE button indicator is off.
z The PAN/TILT ENABLE button indicator blinks while the PAN/TILT lever is being used to operate the switcher.
⇒“Operating the switcher with the PAN/TILT lever and ZOOM button” (page 34)
z The FOCUS/ZOOM/IRIS ENABLE button indicator blinks while the ZOOM button is being used to operate the switcher.
⇒“Operating the switcher with the PAN/TILT lever and ZOOM button” (page 34)
z When the operation of the ENABLE buttons is disabled by menu operation, operating the ENABLE buttons has no effect.
⇒“Enabling or disabling menu operation” (page 28)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the unit operation settings (continued)
Enabling or disabling operation of the
ENABLE buttons by menu operation
Enabling or disabling menu operation
Menu operation can be enabled or disabled.
Operation of the ENABLE buttons can be enabled or disabled by menu
operation.
Disabling operation prevents erroneous operation because the enable/
disable states become unable to be changed even by pressing the
ENABLE buttons.
Disabling MENU operation
1
2
3
Press the MENU button
1
2
3
Press the MENU button
Open RP SETUP menu [25]
Open RP SETUP menu [25]
Turn the F1 dial to display the “5 MENU CONTROL”
item
Turn the F1 dial to display the “4 ENABLE BUTTON”
item
4.ENABLE BUTTON
ACTIVE
4
Turn the F2 dial to select “LOCK”, and then press the F2
dial to confirm the selection
5.MENU CONTROL
LOCK
4
Turn the F2 dial to select “ACTIVE” or “LOCK”, and then
press the F2 dial to confirm the selection
ACTIVE : Enables operation of the ENABLE buttons.
LOCK
: Disables operation of the ENABLE buttons.
z Setting this to “LOCK” stores the ENABLE
button states (operation is enabled or disabled in
accordance with the lighting states), but ENABLE
button operation has no effect.
Menu is Locked.
“Menu is Locked” appears and menu operation is disabled.
z Memory (preset memory and tracing memory) operation is still
possible even when menu operation is disabled.
z Connecting an external device to the TALLY/GPI connector (GPI
input: GPI IN 5) on the rear panel enables the “4. ENABLE BUTTON”
item to be controlled from the external device.
Each time GPI IN 5 is set to On (30 ms or longer), the setting of the
“4. ENABLE BUTTON” item switches between “ACTIVE” and “LOCK”.
Enabling MENU operation
1
Press the MENU button
2
Open RP SETUP menu [25]
5.MENU CONTROL
LOCK
3
Turn the F2 dial to select “ACTIVE”, and then press the
F2 dial to confirm the selection
Menu operation is enabled.
5.MENU CONTROL
ACTIVE
z Connecting an external device to the TALLY/GPI connector (GPI
input: GPI IN 6) on the rear panel enables the “5. MENU CONTROL”
item to be controlled from the external device.
Each time GPI IN 6 is set to On (30 ms or longer), the setting of the
“5. MENU CONTROL” item switches between “ACTIVE” and “LOCK”.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the unit operation settings (continued)
Switching the focus operation and iris
operation
Setting the LCD panel backlight
The backlight of the LCD panel can be turned on or off.
It can also be set to turn off automatically.
The operations of the FOCUS dial and IRIS dial can be switched.
1
2
3
Press the MENU button
Open RP SETUP menu [25]
Turn the F1 dial to display the “3 LCD BACKLIGHT”
item
3.LCD BACKLIGHT
Off
4
Turn the F2 dial to select a setting, and then press the
F2 dial to confirm the selection
On
Off
: Turns on the backlight.
: Turns off the backlight.
60, 120, 180 : Turns off the backlight automatically when the unit
has not been operated within the set time (60, 120,
or 180 minutes).
1
2
3
Press the MENU button
The backlight turns off after the time elapses and
then turns on again when the unit is operated.
Open RP SETUP menu [25]
Turn the F1 dial to display the “1 FOCUS/IRIS” item
1.FOCUS/IRIS
STANDARD
4
Turn the F2 dial to select “EXCHANGE” or
“STANDARD”, and then press the F2 dial to confirm the
selection
EXCHANGE : Switches the operations of the FOCUS dial and
IRIS dial.
z When this is set to “EXCHANGE”, the operations
of the auto focus button and auto iris button are
also switched.
The operations of the one-touch auto focus
button and FOCUS SPEED dial are not
changed.
STANDARD : Restores the default operations of the FOCUS dial
and IRIS dial.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the unit operation settings (continued)
Functions that
can be selected
Assigning functions to the USER buttons
Operations when USER buttons pressed
Pressing a USER button with a function assigned
selects the corresponding ND filter and turns on
the button indicator.
The selected ND filter value differs depending on
the remote camera being controlled.
Functions can be assigned to the eight USER buttons (USER 1 to
USER 8).
This enables you to operate a desired function by simply pressing a
USER button (USER 1 or USER 8).
<Selected ND filter value>
Functions that can be assigned
Remote
camera
ND1
ND2
ND3
ND4
AW-HE120
Through
Clear
1/4
1/4
1/16
1/16
1/64
1/64
AK-HC1500
AK-HC1800
ND1,
USER buttons (USER 1 to USER 8)
ND2,
ND3,
ND4
AW-HE870
AW-E860
AW-E750
AW-E650
AW-E350
1
2
3
Press the MENU button
Off/On*
―
―
―
Open USER BUTTON menu [35]
AW-HE100
AW-HE60
AW-HE50
—
―
―
―
Turn the F1 dial to display the USER button (USER 1 to
USER 8) you want to set
*
: Each press of the USER button with ND1
assigned switches between Off and On.
— : The remote camera setting is not changed
even if a USER button with a function
assigned is pressed.
4
Turn the F2 dial to select a function, and then press the
F2 dial to confirm the selection
1.USER1
ND1
SWLINK,
BUSCONT,
FASSIST,
CAMSEL,
TALLY_IP,
CAMINF
Assign these settings when using the function for
linking with a switcher.
⇒“Setting the functions for when the unit is
linked with the switcher” (page 32)
Holding down a USER button with the function
assigned turns on the indicator of the button for
an instant and sends a power-off request to all
the connected remote cameras.
POWER OFF
CAM_PINP CTL,
Assign these settings when an AW-HE2 HD
CAM_PINP MODE, integrated camera is connected.
CAM_PINP POS
⇒ “Operations of AW-HE2” (page 51)
Note
z When executing the function assigned to a USER button, press
the SHIFT button to turn off its indicator and then perform the
operation.
When a USER button is pressed while the SHIFT button indicator
is on, either the preset memory group is called or shooting mode
selection of the remote camera is executed.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting linking with a switcher
Configure the settings for linking the unit with an optional switcher.
To use the function for linking with a switcher, you need to set the
following in advance.
Enabling or disabling the function for
linking with the switcher
Enable or disable the entire function for linking between the unit and
switcher.
Settings for the connection between unit and switcher
Refer to “Settings for connecting with the remote cameras and
switcher” in Basics (page 29).
„
1
2
3
Press the MENU button
Settings on the switcher
„
The following settings can be configured on the AW-HS50.
z Enabling the function for linking with the unit
Set the “10. CamContLink” item of [13] Operation Menu to “On”.
z Displaying the remote camera names sent by the unit
Set the “4. Name Type” item of [10.1] Input Menu/SDI-IN1
to [10.4] Input Menu/SDI-IN4 or the “2. Name Type” item of
[10.5] Input Menu/DVI-IN to “CAM Name”.
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “1 SWLINK” item
1.SWLINK
On
z Displaying icons at the bottom left of the sub screen for
images of the remote camera selected on the unit when the
switcher is outputting images of multi view
Set “6. Input Status” of [8] MultiView Out/Frame Menu to “On”.
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
For details, refer to the operating instructions for the switcher.
On : Enables the function for linking with the switcher.
Off : Disables the function for linking with the switcher.
Registering the camera numbers that will correspond
to the image inputs of the switcher
Refer to the relevant explanation in this section.
„
„
Enabling or disabling the function for linking with the
switcher
Refer to the relevant explanation in this section.
z Enabling and disabling the link function can be assigned to a USER
button.
Open USER BUTTON menu [35], display one of the “1 USER1”
to “8 USER8” items, and set “SWLINK”
z When the USER button with “SWLINK” assigned is pressed, the
operation is as follows.
Registering the camera numbers that will
correspond to the image inputs of the
switcher
Button indicator on : Enables the function for linking with the
switcher.
Button indicator off : Disables the function for linking with the
switcher.
1
Press the MENU button
2
Open SW INPUT menu [43]
3
Turn the F1 dial to display the input signal of the
switcher to be set
1.INPUT1
CAM1
Input signal : Select from 1. INPUT1 to 100. INPUT100.
4
Turn the F2 dial to select the corresponding camera
number, and then press the F2 dial to confirm the
selection
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the functions for when the unit is linked with the switcher
Set the functions that can be used when there is a link between the unit
and switcher.
Each of the functions needs to be set in advance in SW FUNCTION
menu [42] and SW INPUT menu [43].
Setting the switcher bus to control with the BUSCONT
function
When the BUSCONT function is enabled, you can set the switcher
bus to control with a camera selection button [CAMERA SELECT/
GROUP SELECT] on the unit.
⇒“Registering the camera numbers that will correspond to the image
inputs of the switcher” (page 31)
⇒“Enabling or disabling the function for linking with the switcher”
(page 31)
1
2
3
Press the MENU button
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “3 BUS” item
BUSCONT function
Select the bus material of the switcher from the unit.
When the BUSCONT function is enabled, the bus material of the
switcher can be selected in conjunction with camera selection on the
unit.
3.BUS
AUX
Note
4
Turn the F2 dial to select a setting, and then press the
F2 dial to confirm the setting
z When the link setting of a camera number is changed with
AUTO IP menu [37], SWAP IP menu [38], or MANUAL IP menu
[39] or a camera number corresponding to an image input of
the switcher is changed with SW INPUT menu [43], the bus
material of the switcher will not be changed immediately even
if the BUSCONT function is enabled. Press one of the camera
selection buttons [CAMERA SELECT/GROUP SELECT] to make
a selection again.
AUX : The AUX bus of the switcher is the control target.
PVW : The PVW bus of the switcher is the control target.
PinP : The PinP bus of the switcher is the control target.
KEY : The KEY bus of the switcher is the control target.
Enabling or disabling the BUSCONT function
1
2
3
Press the MENU button
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “2 BUSCONT” item
2.BUSCONT
Off
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
On : Enables the BUSCONT function.
Off : Disables the BUSCONT function.
z Enabling and disabling the BUSCONT function can be assigned to a
USER button.
Open USER BUTTON menu [35], display one of the “1 USER1”
to “8 USER8” items, and set “BUSCONT”
z When the USER button with “BUSCONT” assigned is pressed, the
operation is as follows.
Button indicator on : Enables the BUSCONT function.
Button indicator off : Disables the BUSCONT function.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the functions for when the unit is linked with the switcher (continued)
FOCUS ASSIST function
CAMERA SELECT view function
Control the AUX bus of the switcher and switch between the images of
multi view and the images of the selected remote camera.
Assigning this function to a USER button makes it optimal for adjusting
the focus and other settings because you can fill the screen with the
images of the selected remote camera with just the press of a button.
Set the unit to display icons at the bottom left of the sub screen for
images of the selected remote camera when the switcher is outputting
images of multi view.
Enabling or disabling the CAMERA SELECT function
Setting the FOCUS ASSIST function
1
2
3
Press the MENU button
1
2
3
Press the MENU button
Open SW FUNCTION menu [42]
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “5 CAMERA SELECT”
item
Turn the F1 dial to display the “4 FOCUS ASSIST” item
5.CAMERA SELECT
Off
4.FOCUS ASSIST
Off
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
On : Enables the CAMERA SELECT view function.
On : Switches the images of the AUX bus output from the
switcher to the images of the remote camera selected with
the unit.
Off : Disables the CAMERA SELECT view function.
Off : Switches the images of the AUX bus output from the
switcher to the images of multi view.
z The FOCUS ASSIST function can be assigned to a USER button.
Open USER BUTTON menu [35], display one of the “1 USER1”
to “8 USER8” items, and set “FASSIST”
z When the USER button with “FASSIST” assigned is pressed, the
operation is as follows.
Button indicator on : Switches the images of the AUX bus output
from the switcher to the images of the remote
camera selected with the unit.
Button indicator off : Switches the images of the AUX bus output
from the switcher to the images of multi view.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the functions for when the unit is linked with the switcher (continued)
4
Turn the F2 dial to select a setting, and then press the
F2 dial to confirm the selection
TALLY IP function
CAM:
Enable TALLY IP to receive OA tally information from the switcher via
the network.
The lighting statuses of the camera status indicators on the unit and the
tally lamps on the remote cameras are changed based on the received
OA tally information.
Allows you to operate the remote camera selected on the unit with
the PAN/TILT lever and ZOOM button.
SW:
Allows you to change the switcher settings with the PAN/TILT lever
and ZOOM button.
Enabling or disabling the TALLY IP function
Button Select:
1
2
3
Allows you to select the operation target of the PAN/TILT lever and
ZOOM button (remote cameras or switcher) by pressing the PAN/
TILT ENABLE button or FOCUS/ZOOM/IRIS ENABLE button.
Press the MENU button
Open SW FUNCTION menu [42]
For each of the setting values above, the lighting state of the button
indicator changes as follows when the PAN/TILT ENABLE button or
FOCUS/ZOOM/IRIS ENABLE button is pressed.
Turn the F1 dial to display the “6 TALLY_IP” item
6.TALLY_IP
Off
<Change of lighting state when each ENABLE button is pressed>
Setting value
CAM
Lighting state
On
Off
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
SW
Blinking
Off
On : Enables the TALLY IP function.
Off : Disables the TALLY IP function.
Button Select
On
Blinking
Off
z To enable tally lamp on instructions to be sent to a remote camera
based on the tally information received from the switcher, you need to
display the “3. TALLY OUT” item in CAMERA SETUP menu [24] and
then set it to “On”.
The following shows the operation with respect to the lighting state of
each ENABLE button.
Note
<PAN/TILT ENABLE button>
z The unit also sends the tally lamp on instruction to the
corresponding remote camera when the unit receives tally
information for a camera number belonging to a camera group
that is not selected.
Button indicator
state
Operation when the PAN/TILT lever is
operated
On
The remote camera is able to move horizontally
and vertically.
The switcher PinP, wiper, and chroma key marker
positions (X, Y) are able to move left/right and
up/down.
Blinking
Off
Operation is disabled.
Operating the switcher with the PAN/TILT
lever and ZOOM button
<ZOOM/FOCUS/IRIS ENABLE button>
Button indicator
state
Operation when the PAN/TILT lever is
operated
You can use the unit's PAN/TILT lever and ZOOM button to change
switcher settings (PinP position and size, etc.).
On
The lens zoom of the remote camera can be
changed.
The switcher PinP and chroma key marker sizes
can be changed.
Blinking
Off
Setting the application of the PAN/TILT lever and
ZOOM button
Operation is disabled.
1
2
3
Press the MENU button
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “7 P/T/Z CONTROL” item
7.P/T/Z CONTROL
CAM
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the functions for when the unit is linked with the switcher (continued)
Selecting the remote camera setting information to
superimpose on the images output from the switcher
CAM INF function
You can display the remote camera setting information acquired by the
unit on the switcher AUX bus output images or multi view images.
1
Press the MENU button
2
Open SW FUNCTION menu [42]
Enabling or disabling the CAM INF function
3
Turn the F1 dial to display any of the “9 CAMINF_
FORMAT” to “16 CAMINF_ALARM” items
1
2
3
Press the MENU button
9.CAMINF_FORMAT
Open SW FUNCTION menu [42]
Turn the F1 dial to display the “8 CAM INF” item
On
16.CAMINF_ALARM
On
8.CAM INF
Off
9 CAMINF_FORMAT
:
Video format
1
(This is left blank when the video
format of the remote camera cannot
be recognized.)
Remote camera name
Shooting mode
Gain value
Shutter information (ON/OFF,
shutter value)
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
On : Enables the CAM INF view function.
Off : Disables the CAM INF view function.
10 CAMINF_CNAME
11 CAMINF_SCENE
12 CAMINF_GAIN
:
:
:
:
2
3
4
5
13 CAMINF_SHUTER
14 CAMINF_IRIS
15 CAMINF_FILTER
16 CAMINF_ALARM
:
:
:
Iris value
Filter information
Remote camera alarm information
6
7
8
z Enabling and disabling the CAM INF function can be assigned to a
USER button.
Open USER BUTTON menu [35], display one of the “1 USER1”
to “8 USER8” items, and set “CAMINF”
z When the USER button with “CAMINF” assigned is pressed, the
1080/59i
1/100
USER
AUTO
operation is as follows.
Button indicator on : Enables the CAM INF function.
Button indicator off : Disables the CAM INF function.
AW-HE120
4
For each of the items, turn the F2 dial to select “On”
or “Off”, and then press the F2 dial to confirm the
selection
On : Enables display on the switcher.
Off : Disables display on the switcher.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory card operations
The unit allows you to use a memory card to perform the following
operations.
z Memory cards
Memory cards used with the unit should conform to SD or SDHC
standards.
SAVE : Save the configuration data of the unit or a remote camera to a
memory card.
Be sure to use the unit to format memory cards.
Memory cards with the following capacity can be used with the
LOAD : Load the configuration data saved to a memory card to the unit
or a remote camera.
unit.
SDXC memory cards and MultiMediaCards (MMC) are not
supported.
SD
8 MB to 2 GB
<Data Target for SAVE and LOAD>
SDHC 4 GB to 32 GB
Data
type
Description of
data
SAVE/
LOAD
File names*1
Configuration data RP01.s12 to
SAVE and
LOAD
SETUP
For the latest information not described in the Operating
Instructions, refer to the following websites.
of unit*2
RP99.s12
Preset data and
tracing data*3
RP01.m12 to
RP99.m12
SAVE and
LOAD
MEM
Configuration data RP01.c12 to
of remote camera*4 RP99.c12
SAVE and
LOAD
CAM
z Observe the following points when using and storing the
memory cards.
• Avoid high temperature and humidity.
• Avoid water droplets.
Unit version update V*****.s12 to
UPGRADE
LOG
LOAD only
SAVE only
file
V*****.s12
RP01.log to
RP99.log
Unit operation log
• Avoid static electricity.
*1 : When SAVE is executed on the unit, the file names above are
assigned automatically.
Also, after SAVE is executed on the unit, the file names can be
changed with a personal computer.
· About file names
SETUP: ********.s12
MEM: ********.m12
CAM: ********.c12
Use up to eight single-byte alphanumeric characters for the ********
part above. A file name other than the above may not be displayed
properly on the unit.
*2 : The IP address, subnet mask, and default gateway settings of the
unit are not target for the SAVE and LOAD operations.
*3 : Only the data for the selected remote camera.
The PRESET SPEED value set for each preset is loaded and
saved.
*4 : Only the data for the selected remote camera.
Note
z SAVE and LOAD are not possible with the MEM and CAM items
of a camera connected via a serial connection.
Precautions on handling memory cards
z Never remove a memory card while the memory card access lamp
is lit or blinking.
If you remove a memory card while the memory card access lamp is
lit or blinking, the data saved to the memory card may be lost.
z The data stored in a memory card may be lost due to, for example,
the loss or incorrect operation of the memory card.
We recommend saving any important data to a computer or other
device.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory card operations (continued)
Initializing a memory card (INIT)
Saving data to a memory card (SAVE)
Before using a memory card with the unit, be sure to initialize the
memory card with the unit
When the memory card is initialized, the memory card is formatted (in
compliance with SD standards) and dedicated directories are created.
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select a remote
camera
Note
2
Press the MENU button to turn on its indicator
z If you initialize a memory card, all of the files stored in the
memory card will be deleted.
3
Open SD SAVE menu [46]
SAVE MODE:SETUP
1
Press the MENU button to turn on its indicator
2
Open SD DELETE menu [48]
4
DEL MODE :SETUP
Turn the F1 dial to select the type of data to save to the
memory card, and then press the F1 dial to confirm the
selection
The file name assigned automatically in accordance with the
selected data type is displayed on the second line of the LCD panel.
3
Turn the F1 dial to display the “INIT” item, and then
press the F1 dial to confirm the selection
SAVE MODE:MEM
RP10.m12
DEL MODE :INIT
NO
z You can select a data type from SETUP, MEM, CAM, and LOG.
z The name of the file to be saved cannot be changed from the unit.
z When no memory card is inserted, “NO CARD!” appears.
z Up to 99 files of each of SETUP, MEM, CAM, and LOG can be
saved to one memory card.
4
Turn the F2 dial to select “YES”
When 99 files already exist, “OVER 99FILES!” appears, and
saving is not possible.
Delete files and then execute saving again.
DEL MODE :INIT
YES
⇒ “Deleting the files saved to a memory card (DELETE)” (page 38)
5
Press the F2 dial
Initialization of the memory card begins.
z When no memory card is inserted, “NO CARD!” appears.
5
Press the F2 dial to confirm the selection
Saving to the memory card begins.
SAVING
NOT REMOVE CARD.
...
INITIALIZING
COMPLETE.
...
COMPLETE.
z When saving completes, “COMPLETE.” appears.
z When saving fails, “SAVE ERROR!” appears. Replace the memory
card and then execute saving again.
z When initialization completes, “COMPLETE.” appears.
z When initialization fails, “INITIAL ERROR!” appears. Replace the
memory card and then execute initialization again.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory card operations (continued)
Loading data from a memory card (LOAD)
Deleting the files saved to a memory card
(DELETE)
1
Press one of the camera selection buttons
[CAMERA SELECT/GROUP SELECT] to select a remote
camera
1
Press the MENU button to turn on its indicator
2
Open SD DELETE menu [48]
2
Press the MENU button to turn on its indicator
DEL MODE :SETUP
3
Open SD LOAD menu [47]
LOAD MODE:SETUP
3
Turn the F1 dial to select the type of data to delete, and
then press the F1 dial to confirm the selection
The name of the file saved to the memory card is displayed on the
second line of the LCD panel.
4
Turn the F1 dial to select the type of data to load from
the memory card, and then press the F1 dial to confirm
the selection
DEL MODE :MEM
RP10.m12
The file saved to the memory card is displayed on the second line of
the LCD panel.
z You can select a data type from SETUP, MEM, CAM, and LOG.
For the operation when “INIT” is selected, refer to “Initializing a
memory card (INIT)” (page 37).
LOAD MODE:MEM
RP10.m12
z When no memory card is inserted, “NO CARD!” appears.
z You can select a data type from SETUP, MEM, CAM, and
UPGRADE.
z When no memory card is inserted, “NO CARD!” appears.
4
Turn the F2 dial to select a file to delete, and then press
the F2 dial to confirm the selection
The file is deleted.
5
COMPLETE
.
Turn the F2 dial to select a file, and then press the F2
dial to confirm the selection
The data begins to be read from the memory card and transfered to
the unit or selected remote camera.
z When deleting completes, “COMPLETE.” appears.
z When deleting fails, “DELETE ERROR!” appears. Save any
necessary files to a computer and then initialize the memory card.
z When a file that cannot be loaded to the selected remote camera
is specified (when, for example, you specify a file of a remote
camera that is a different model), “LOAD FILE IMCOMPATIBLE!”
appears.
LOADING
...
NOT REMOVE CARD.
COMPLETE.
z When loading completes, “COMPLETE.” appears.
z When loading fails, “LOAD ERROR!” appears. Save the data to
the memory card again and then execute loading again. If loading
is still not possible, replace the memory card.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Tally settings
The unit can receive the tally information of the switcher and other
external devices from the TALLY/GPI connector (TALLY input) on the
rear panel and two network lines.
Setting the sending of tally information from
the unit to remote cameras
To enable turning on the camera status indicators on the unit and
the tally lamps on the remote cameras based on the received tally
information, you need to configure the following settings.
1
Press the MENU button
2
Open CAMERA SETUP menu [24]
Turn the F1 dial to display the “3 TALLY OUT” item
Registering the camera numbers that will correspond
to the tally inputs
Setting is required to use TALLY IN1 to TALLY IN10 signals from the
TALLY/GPI connector (TALLY input) on the rear panel.
Refer to the relevant explanation in this section.
„
3
3.TALLY OUT
Off
Registering the camera numbers that will correspond
„
to the image inputs of the switcher
Setting is required to use tally information received via the network.
Refer to “Setting linking with a switcher” (page 31).
4
Turn the F2 dial to select “On” or “Off”, and then press
the F2 dial to confirm the selection
Setting the sending of tally information from the unit
to remote cameras
Refer to the relevant explanation in this section.
„
„
On : Sends tally information to remote cameras.
Off : Does not send tally information to remote cameras.
Settings on remote cameras
Setting is required on the remote camera to enable turning on the
tally lamp.
Refer to the operating instructions for the remote camera.
Registering the camera numbers that will
correspond to the tally inputs
1
Press the MENU button
2
Open TALLY menu [44]
3
Turn the F1 dial to select the TALLY input connector
number
1.TALLY IN1
CAM1
Input connector number : Select form TALLY IN1 to TALLY IN10
4
Turn the F2 dial to select the corresponding camera
number, and then press the F2 dial to confirm the
selection
Camera number : Select from CAM1 to CAM100.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking alarm information
In the event of an error with the power supply of the unit or a remote
camera included in the selected camera group, the ALARM indicator on
the unit turns on and the output of the GPI OUT connector (GPI OUT 5)
becomes On.
When an error occurs, you can check the alarm information by menu
operation.
Displaying alarm information
1
2
3
Press the MENU button
Open ALARM menu [50]
Turn the F1 dial to display the item you want to check
The alarm status is displayed on the bottom line of the LCD panel.
1.POWER
NO ALARM
<Details of each alarm>
[Select 1 POWER]
Allows you to check the unit’s power supply alarm.
No ALARM:
When the power supply is trouble-free.
ALARM:
When trouble has occurred with the power supply.
[Select 2 CAM1 to 101 CAM100]
Displays the alarm information for camera numbers included in the
currently selected camera group.
No ALARM:
Trouble-free.
FAN ALM:
Trouble has occurred with the cooling fan.
P/T ALM:
Trouble has occurred with the pan/tilt operation.
FAN ALM+P/T ALM:
Trouble has occurred with the cooling fan and pan/tilt
operation.
Note
z When an alarm has occurred, stop operation immediately and be
sure to contact your dealer.
Continued use may cause the unit or a remote camera to
malfunction.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Returning the unit to the factory default state (INITIALIZE)
Also, when you execute INITIALIZE (ALL or SETUP), the data stored
on the unit and the following statuses are restored to the factory default
state.
You can restore the settings stored on the unit to the factory defaults
(INITIALIZE)
When executing INITIALIZE, select one of “ALL” or “SETUP”.
z Tracing data
z Speed at which to move to the preset recall position
(PRESET SPEED)
z Remote camera selection status
z Camera group selection status
z ENABLE button lighting statuses
ALL
: Restores all settings to the factory default state (executes
INITIALIZE).
SETUP : Restores only some settings to the factory default state
(executes INITIALIZE).
Note
z For details on initializing the settings stored on a remote camera,
refer to the operating instruction supplied with the remote camera.
√: Target, ―: Not target
<Setting items stored on the unit>
INITIALIZE
Button
Menu name
number
Setting item
ALL
SETUP
[24]
[25]
CAMERA SETUP
RP SETUP
1. CAM POWER
2. AUTO ON
√
√
√
√
√
√
√
√
√
√
3. TALLY OUT
1. FOCUS/IRIS
2. P/T CURV
3. LCD BACKLIGHT
4. ENABLE BUTTON
5. MENU CONTROL
6. GLOBAL AREA
7. IP ADDRESS
√
√
√
√
√
√
√
―
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
―
―
―
―
―
√
8. SUBNETMASK
9. GATEWAY
10. MAC ADDRESS
11. PORT CAM1 to 110. PORT CAM100
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. PM GRP1 MODE
[26]
[27]
[28]
[29]
[31]
PAN DIRECTION
TILT DIRECTION
ZOOM DIRECTION
FOCUS DIRECTION
PM GRP1
√
√
√
√
2. PM GRP1 1/10 to 11. PM GRP1 10/10
12. PM GRP1 ALL
√
√
[32]
[33]
[34]
PM GRP2
PM GRP3
PM GRP4
1. PM GRP2 MODE
√
2. PM GRP2 1/10 to 11. PM GRP2 10/10
12. PM GRP2 ALL
√
√
1. PM GRP3 MODE
√
2. PM GRP3 1/10 to 11. PM GRP3 10/10
12. PM GRP3 ALL
√
√
1. PM GRP4 MODE
√
2. PM GRP4 1/10 to 11. PM GRP4 10/10
12. PM GRP4 ALL
√
√
[35]
[36]
[38]
[39]
[40]
[41]
USER BUTTON
CTRL TYPE
SWAP IP
1. USER1 to 8. USER8
√
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. CAM1 to 100. CAM100
1. SW CTL
―
―
―
―
―
―
√
MANUAL IP
PORT NO
SW SETUP
2. SW IP ADDRESS
[42]
[43]
[44]
[45]
SW FUNCTION
SW INPUT
TALLY
1. SWLINK to 16. CAMINF_ALARM
1. INPUT1 to 100. INPUT100
1. TALLY IN1 to 10. TALLY IN10
1. CAM OUT1 to 10. CAM OUT10
―
√
GPI OUT
√
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Returning the unit to the factory default state (INITIALIZE) (continued)
√: Target, ―: Not target
<Setting items stored on the unit (cont )>
INITIALIZE
Button
number
Menu name
Setting item
ALL
SETUP
―
[49]
SYSTEM
2. SYSTEM VER
3. PROGRAM VER
4. FPGA VER
―
―
―
―
―
z For the factory default settings, refer to “Table of setting items (menus)” (pages 53 to 55).
Returning the unit to the factory default
state
1
2
3
Press the MENU button
Open SYSTEM menu [49]
Turn the F1 dial to display the “1 INITIALIZE” item
1.INITIALIZE
ALL
4
Turn the F2 dial to select “ALL” or “SETUP”, and then
press the F2 dial to confirm the selection
INITIALIZE is executed.
ALL
: Restores all settings to the factory default state (executes
INITIALIZE).
SETUP : Restores only some settings to the factory default state
(executes INITIALIZE).
Note
z The unit needs to be rebooted after selecting “ALL” and then
executing INITIALIZE. Turn the power off and then back on.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Control interface for external devices
TALLY/GPI (JST: JBY‑25S‑1A3F(LF)(SN))
„
Pin number
Signal name
Description of signal
Operation
13
1
1
TALLY IN 1
TALLY IN 2
14
14
25
2
TALLY IN 3
15
TALLY IN 4
TALLY IN 5
TALLY IN 6
TALLY IN 7
TALLY IN 8
TALLY IN 9
TALLY IN 10
GND
TALLY IN1 to TALLY IN10 tally inputs
Contact input
3
⇒ “Tally settings” (page 39)
(Status operation)
16
4
17
5
18
6
GND
19
GPI IN 1
Calling of PMEM GROUP1 to PMEM GROUP4
⇒ “Operating preset memory groups (PMEM
GROUP)” (page 16)
7
GPI IN 2
20
GPI IN 3
Contact input
(Trigger operation)
z Trigger width
30 msec
8
GPI IN 4
Control of the ENABLE BUTTON settings
⇒ “Configuring the unit operation settings” (page 27)
21
GPI IN 5
GPI IN 6
Control of MENU CONTROL settings
⇒ “Configuring the unit operation settings” (page 27)
9
22
GND
GND
10
23
11
24
12
25
13
GPI OUT 1
GPI OUT 2
GPI OUT 3
GPI OUT 4
GPI OUT 5
GND
Remote camera selection 0*
Remote camera selection 1*
Remote camera selection 2*
Remote camera selection 3*
Alarm
Open collector output
(Status operation)
GND
NC
Example of GPI OUT connection
Ensure that the conditions given below
are satisfied.
Example of TALLY IN and GPI IN connections
Provide contact inputs.
Withstand voltage: Max. 24 V DC
Current: Max. 50 mA
AW‑RP120
+3.3 V
(Max voltage 24 V)
AW‑RP120
TALLY IN
GPI IN
GPI OUT
(Max current 50 mA)
GND
GND
For the cameras registered to the “1. CAM OUT1” to “10. CAM OUT10” items in GPI OUT menu [45], the
selection states on the unit can be output to GPI OUT1 to GPI OUT4.
<Output states of GPI OUT1 to GPI OUT4 when the camera number registered to CAM OUT is
selected>
Output of GPI OUT1 to GPI OUT4
GPI OUT1
On
GPI OUT2
Off
GPI OUT3
Off
GPI OUT4
Off
CAM OUT1
CAM OUT2
CAM OUT3
CAM OUT4
CAM OUT5
CAM OUT6
CAM OUT7
CAM OUT8
CAM OUT9
CAM OUT10
Off
On
Off
Off
On
On
Off
Off
Off
Off
On
Off
On
Off
On
Off
Off
On
On
Off
On
On
On
Off
Off
Off
Off
On
On
Off
Off
On
Off
On
Off
On
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Control interface for external devices (continued)
REMOTE
(JST: JEY‑9S‑1A3F(LF)(SN))
„
Registering camera numbers to CAM OUT1 to
CAM OUT10
You can connect a personal computer or other external device to select
the camera group, select the remote camera, and recall preset memory
or tracing memory.
1
2
3
Press the MENU button
For further details, contact your dealer.
Open GPI OUT menu [45]
Pin number
Signal name
---
1
5
1
2
3
4
5
6
7
8
9
Turn the F1 dial to display the “1 CAM OUT1” item
RXD IN
TXD OUT
DTR
9
6
1.CAM OUT1
CAM1
GND
DSR
4
Turn the F2 dial to select the camera number to set for
CAM OUT1, and then press the F2 dial to confirm the
selection
RTS
CTS
---
Camera number : Select from CAM1 to CAM100.
5
Turn the F1 dial to display any of the “2 CAM OUT2”
to “10 CAM OUT10” items and then register a camera
number
TO PAN/TILT HEAD 1 to 5 connectors
(RJ‑45)
„
z Repeat steps 3 to 4.
Connect remote cameras with support for a serial connection to these
connectors using LAN cables.
Connect them with straight cables (category 5 or above).
Pin
number
Signal name
Description of signal
1
2
3
4
5
6
7
8
GND
TALLY
TXD –
RXD –
RXD+
TXD+
NC
Frame ground
Tally output (open collector)
Send data (–)
Receive data (–)
Receive data (+)
Send data (+)
Not used
NC
Not used
z TALLY (pin number: 2) specifications
Voltage withstand: Max. 24 V DC
Current: Max. 50 mA
LAN connector (RJ‑45)
„
Connect a remote camera, switcher, or computer that supports an IP
connection to this connector with a LAN cable.
When directly connecting a device to the unit, use a crossover cable
(category 5 or above).
When connecting via a hub (switching hub) or other device, use a
straight cable (category 5 or above).
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software
Setup Software is an application that allows you to configure the settings for connecting the unit with remote cameras and a switcher from a personal
computer.
Note
When using Setup Software to configure the settings from a personal computer, observe the following
z Do not perform any operation on the unit.
z Do not start Setup Software on any other computer in the same network.
z Do not use “Easy IP Setup Software” supplied with AW-HE120, AW-HE60, and AW-HE50.
Installing the software
This section describes how to install Setup Software.
1. Insert the CD-ROM supplied with the unit into the CD-ROM drive of the personal computer on which the application is going to be installed.
2. Copy the entire folder containing “Setup Software” on the CD-ROM to the hard disk drive of the personal computer.
3. Double-click “RP120Tool.exe” in the copied “Setup Software” folder to start Setup Software.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software (continued)
Registering the unit in Setup Software
On the “IP Address” tab, register the IP addresses of units to be set from Setup Software.
The units registered here can be selected from the list box on the “Setting” tab.
Up to five units can be registered.
1
Enter the IP addresses in the IP address boxes
In the RP1 to RP5 boxes, enter the IP addresses of the AW-RP120
to register.
2
Click [SET]
3
In the list box on the “Setting” tab, select the AW‑RP120
whose data is to be referenced
The settings configured on the selected unit are displayed on the
“Setting” tab.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software (continued)
Settings for connecting with the remote cameras and switcher
On the “Setting” tab, configure the settings for the connections between the unit and the remote cameras and switcher.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software (continued)
Displaying the “Setting” tab
1
2
3
4
5
6
7
8
9
10
11
12
13
1
Setting target selection list box
Select the unit for which to configure the connection settings.
Click to display the IP addresses of the units that can be set from
this software. Select the IP address of the unit you want to set from
this list.
Any of the units registered in the “IP Address” tab can be selected.
⇒ “Registering the unit in Setup Software” (page 46)
8
9
MAC ADDRESS
Displays the MAC addresses of the remote cameras and switcher
linked to the camera numbers on the unit.
IP ADDRESS
Set the IP addresses of the remote cameras and switcher that are
connection destinations.
After input, click the [SET] button to reflect the changes.
2
CAMERA/SW
Displays the types of devices to be connected.
10 CAMERA PORT NO
CAMERA : Remote camera
Set the port numbers of the remote cameras that are connection
destinations.
SW
: Switcher
After input, click the [SET] button to reflect the changes.
Possible setting range: 1 to 65535
However, the following values cannot be set even though they are
within this range.
20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161, 162, 995, 10669,
10670
3
4
5
CAMERA GROUP
Displays the camera group numbers.
CAMERA NO
Displays the camera numbers.
11 SWAP CAMERA
CTRL TYPE
Select the connection types.
Swap the remote cameras set as connection destinations between
two camera numbers.
Click
on the right and select a connection type from “Serial”,
“Network”, or “NoAsign”.
Click
to display camera numbers “C001” to “C100”.
Serial
: Serial connection
Select the camera number with which you want to make the swap from
this list.
After making a change, click the [SET] button to reflect the change.
Network : IP connection
NoAsign : No setting (default setting)
“Serial” can only be selected with GROUP1.
12 RECEIVE PORT NO
After making a change, click the [SET] button to reflect the change.
Set the port numbers for the unit to receive camera information
update notifications from remote cameras.
Possible setting range: 61000 to 65534
6
CAMERA NAME
Displays the names of the cameras set on the remote cameras.
They are displayed for the remote cameras in the currently selected
group.
For remote cameras with a serial connection, a name is only
displayed when a
Only an even number can be set.
Even if an odd number is entered and then the [SET] button is clicked,
the value is not reflected.
remote camera is selected on the unit.
13 ALARM
Displays the alarm information of the remote cameras.
It is displayed for the remote cameras belonging to the camera
group selected on the unit.
For remote cameras with a serial connection, the information is only
displayed when a remote camera is selected on the unit.
7
SW INPUT
Set the image inputs of the switcher that correspond to the camera
numbers on the unit.
Click
on the right and select an option from “NoAsign” and “INPUT1”
to “INPUT100".
After making a change, click the [SET] button to reflect the change.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software (continued)
Executing auto IP setting
Swapping the remote cameras that are connection
destinations
You can execute “auto IP setting” of the unit from Setup Software.
Swap the remote cameras set as connection destinations between two
camera numbers.
Updating the IP addresses of the remote cameras and
switcher automatically from the unit
„
1
Click
of the “SWAP CAMERA” item
Camera numbers “C001” to “C100” appear in the list box.
Select the camera number with which you want to make the swap
from this list.
1
Click [RENEW]
The IP addresses are displayed for the link target camera numbers
and switcher.
z When [CANCEL] is clicked, the original settings are restored.
2
Click [SET]
The remote cameras set as connection destinations are swapped
between the two camera numbers.
2
„
1
Click [SET]
The displayed IP addresses are set on the remote cameras and
switcher.
Setting the image inputs of the switcher that
correspond to camera numbers
Leaving the IP addresses set on the remote cameras
and switcher unchanged and automatically updating
the connection destination IP addresses set on the
unit
Set the image input of the switcher that will correspond to each camera
number.
1
Click
of the “SW INPUT” item
Click [KEEP]
Switcher image inputs “INPUT1” to “INPUT100” appear.
Set the image input that will associated with each camera number.
The IP addresses set for the remote cameras and switcher are
displayed for the link target camera numbers and switcher.
z When [CANCEL] is clicked, the original settings are restored.
2
Click [SET]
2
The image input of the switcher is associated with the camera
number.
Click [SET]
The displayed IP addresses are set as the connection destination IP
addresses of the unit.
Initializing the IP addresses
Changing the connection destination IP addresses
Clicking [ALL CLEAR] initializes the connection settings that are set on
the unit.
Set the IP addresses that are the connection destinations of the unit.
1
Directly enter the IP address of the device concerned in
the [IP Address] box
Acquiring the connection settings
2
Click [SET]
The new IP address is applied.
Clicking [REFRESH] acquires the connection settings for the unit
selected in the setting target selection list box, and refreshes the display.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Software (continued)
Setting user authentication
To control remote cameras that have the user authentication function enabled, you need to set the user name and password on the AW-RP120.
Configure this setting on the “User Auth.” tab of this application.
1
2
3
Enter the user name in the User Name
box
Enter the password in the Password box
Entered characters are displayed as “*”.
Enter the same password as above in the
Retype password box
Entered characters are displayed as “*”.
4
Click [SET]
The user name and password are set on
AW-RP120.
Clicking [REFRESH] clears the user name
and password
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations of AW‑HE2
<Invalid menu operations>
Menu
AW-HE2 HD integrated cameras can be operated from the unit.
This section describes the operations which are different from the
corresponding operations of other remote cameras.
Setting item
SHUTTER [21]
1. SHUTTER
2. SPEED
Note
ND FILTER [22]
1. ND FILTER
z The method for connecting AW-HE2 and the unit is the same as
that for connecting AW-HE2 and AW-RP50. Refer to the operating
instructions supplied with AW-HE2.
PTZ ADJUST [30]
2. SPEED WITH Z
3. LIMIT UP
4. LIMIT DOWN
5. LIMIT LEFT
6. LIMIT RIGHT
<Invalid operations>
Color adjustment
section
R/B GAIN dial, R/B PED, dial, PED dial, GAIN
button, DETAIL button, AUTO GAIN button, ABB
button
Focus, zoom, and FOCUS dial, Auto focus button,
iris section
One-touch auto focus button, FOCUS SPEED
dial
User button
section
SCENE 1 to SCENE 4 buttons (*1)
(*1) Even if you press these buttons while the SHIFT button indicator is
on, the operations will have no effect.
(The shooting mode cannot be selected.)
<Operations which are different>
PAN/TILT lever
When the zoom position is the WIDE end
side, the output images do not change even if
the lever is operated.
Preset memory
z The preset numbers that can be registered
and recalled are PMEM 1 to PMEM 9
(page number: Page 1).
z PRESET SCOPE and PRESET SPEED
cannot be set.
Tracing memory
SD card
Up to nine tracing memory can registered and
recalled for each camera.
SAVE and LOAD of the MEM and CAM items
cannot be executed.
USER buttons
If the following settings are assigned, PinP
display of AW-HE2 can be operated with the
USER buttons.
CAM_PINP CTL:
Displays or hides PinP.
Each press of the button switches in the
order of display PinP → hide PinP →
display PinP, and so on.
CAM_PINP MODE:
Switches the control target (control mode)
of the PAN/TILT lever and ZOOM button.
Each press of the button switches in the
order of PinP → main screen → PinP, and
so on.
CAM_PINP POS:
Changes the display position of PinP.
Each press of the button switches in the
order of top right → bottom right → bottom
left → top left → top right, and so on.
z For the PinP display function of AW-HE2, refer to the operating
instructions supplied with AW-HE2.
.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of setting items (dedicated dials and buttons)
Dial/button
R/B GAIN dial
Setting item
R GAIN
Remote camera
Setting
AW-HE120
–150 to +150
–30 to +30
“---”
B GAIN
AW-HE50 (*), AW-HE60
AW-HE2
AW-HE100
–30 to +30
–150 to +150
–150 to +150
–150 to +150
–150 to +150
“---”
AW-HE870
AW-E860, AW-E750, AW-E650, AW-E350
AK-HC1500, AK-HC1800
AW-HE120
R/B PED dial
R PED
B PED
AW-HE50, AW-HE60
AW-HE2
“---”
AW-HE100
“---”
AW-HE870
–150 to +150
–150 to +150
–100 to +100
–150 to +150
–10 to +10
“---”
AW-E860, AW-E750, AW-E650, AW-E350
AK-HC1500, AK-HC1800
AW-HE120
PED dial
PED
AW-HE50, AW-HE60
AW-HE2
AW-HE100
–30 to +30
–150 to +150
–150 to +150
–150 to +150
AW-HE870
AW-E860, AW-E750, AW-E650, AW-E350
AK-HC1500, AK-HC1800
AW-HE120
GAIN button
GAIN
Auto, 0 dB to 18 dB (1 step)
AW-HE50, AW-HE60
AW-HE2
Auto, 0 dB, 3 dB, 6 dB, 9 dB, 12 dB, 15 dB, 18 dB
“---”
AW-HE100
Auto, 0 dB to 12 dB (1 step), 15 dB, 18 dB
AW-HE870
Auto, –6 dB to 18 dB (1 step)
AW-E860, AW-E750, AW-E650, AW-E350
AK-HC1500, AK-HC1800
AW-HE2
Auto, 0 dB to 30 dB, N/Eye L, N/Eye, N/Eye H
LOW, MID, HIGH, S.GAIN1, S.GAIN2, S.GAIN3
DETAIL button
DETAIL
LEVEL
“---”
Other than AW-HE2
AW-HE120
Off, On
Low, High
Low, High
“---”
AW-HE50, AW-HE60
AW-HE2
AW-HE100
0 to 14
Low, High
Low, High
“---”
AW-HE870
AW-E860, AW-E750, AW-E650, AW-E350
AK-HC1500, AK-HC1800
(*) AW-HE50 without the AW-HEF5HG/AW-HEF5SG upgrade kit installed cannot operate R GAIN and B GAIN.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of setting items (menus)
Button
number
Initial value on
unit (*1)
Menu name
SHUTTER
Setting item
1. SHUTTER
Remote camera
AW-HE120
AW-HE50, AW-HE60
AW-HE2
AW-HE100
AW-HE870
AW-E860, AW-E750,
AW-E650, AW-E350
AK-HC1500, AK-HC1800
AW-HE120
Setting
[21]
–
–
–
–
–
–
Off, Step, Synchro, ELC
Off, Step, Synchro
“---”
Off, Step, Synchro
Off, Step, Synchro, ELC
Off, Step, Synchro, ELC
–
–
Off, Step, Synchro
2. SPEED
59 94 Hz:
1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
50 Hz:
1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
AW-HE50, AW-HE60
–
1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
AW-HE2
AW-HE100
AW-HE870
–
–
–
“---”
1/100, 1/250, 1/500, 1/1000, 1/2000
1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
AW-E860, AW-E750,
AW-E650, AW-E350
AK-HC1500, AK-HC1800
–
–
1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
VIDEO:
1/100, 1/120, 1/250, 1/500, 1/1000,
1/2000
FILM:
180.0, 172.8, 144.0, 120.0, 90.0, 45.0
ND1, ND2, ND3, ND4
[22]
ND FILTER
1. ND FILTER
–
(Only when AW-HE870, AW-E860,
AW-E750, AW-E650, or AW-E350 is
connected)
Off, On
[23]
[24]
FUNCTION
2. DEFROSTER
3. WIPER
–
–
–
Off, On
Off, On
Off, On
4. HEATER/FAN
1. CAM POWER
CAMERA SETUP
GROUP ON
GROUP OFF, GROUP ON, ALL OFF,
ALL ON
On, Off
2. AUTO ON
On
3. TALLY OUT
Off
On, Off
4. HOME POSITION
1. FOCUS/IRIS
2. P/T CURV
SET
STANDARD
1
SET
[25]
RP SETUP
STANDARD, EXCHANGE
1 to 5
3. LCD BACKLIGHT
4. ENABLE BUTTON
5. MENU CONTROL
6. GLOBAL AREA
7. IP ADDRESS
8. SUBNETMASK
9. GATEWAY
On
On, Off, 60, 120, 180
ACTIVE, LOCK
ACTIVE, LOCK
On, Off
ACTIVE
ACTIVE
Off
192.168.0.9
255.255.255.0
192.168.0.1
10. MAC ADDRESS
11. PORT CAM1
Displayed only
61000 to 65534
61000
110. PORT CAM100
1. CAM1
61000
NORMAL
61000 to 65534
NORMAL, REVERSE
[26]
[27]
[28]
[29]
PAN DIRECTION
TILT DIRECTION
100. CAM100
1. CAM1
NORMAL
NORMAL
NORMAL, REVERSE
NORMAL, REVERSE
100. CAM100
ZOOM DIRECTION 1. CAM1
NORMAL
NORMAL
NORMAL, REVERSE
NORMAL, REVERSE
100. CAM100
FOCUS DIRECTION 1. CAM1
NORMAL
NORMAL
NORMAL, REVERSE
NORMAL, REVERSE
100. CAM100
NORMAL
NORMAL, REVERSE
(*1) “–” indicates a setting saved to the remote camera.
A diagonal line indicates a setting that can only be displayed. It cannot be changed.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of setting items (menus) (continued)
Button
number
Initial value on
unit (*1)
Menu name
PTZ ADJUST
Setting item
Remote camera
Setting
[30]
1. Z MIN SPEED
2. SPEED WITH Z
Off
Off, 1 to 8
Off, On
Off, On
“---”
Off, 1, 2
Off, 1, 2
AW-HE120
AW-HE50, AW-HE60
AW-HE2
–
–
–
–
–
AW-HE100
AW-PH360, AW-PH400,
AW-PH405, AW-PH650
AW-HE120
AW-HE50, AW-HE60
AW-HE2
3. LIMIT UP
–
–
–
–
–
Off, On
Off, On
“---”
EXEC
EXEC
AW-HE100
AW-PH360, AW-PH400,
AW-PH405, AW-PH650
AW-HE120
AW-HE50, AW-HE60
AW-HE2
4. LIMIT DOWN
5. LIMIT LEFT
6. LIMIT RIGHT
–
–
–
–
–
Off, On
Off, On
“---”
EXEC
EXEC
AW-HE100
AW-PH360, AW-PH400,
AW-PH405, AW-PH650
AW-HE120
AW-HE50, AW-HE60
AW-HE2
–
–
–
–
–
Off, On
Off, On
“---”
EXEC
EXEC
AW-HE100
AW-PH360, AW-PH400,
AW-PH405, AW-PH650
AW-HE120
AW-HE50, AW-HE60
AW-HE2
AW-HE100
AW-PH360, AW-PH400,
AW-PH405, AW-PH650
–
–
–
–
–
Off, On
Off, On
“---”
EXEC
EXEC
[31]
[32]
[33]
[34]
[35]
PM GRP1
1. PM GRP1 MODE
2. PM GRP1 1/10
3. PM GRP1 2/10
Off
Off, SEPARATE, ALL
NoAsgn:------,
CAM001:PRE001 to CAM100:PRE100
NoAsgn:------
NoAsgn:------
11. PM GRP1 10/10
12. PM GRP1 ALL
1. PM GRP2 MODE
2. PM GRP2 1/10
3. PM GRP2 2/10
NoAsgn:------
NoAsgn
Off
NoAsgn:------
NoAsgn:------
NoAsgn, PRE001 to PRE100
Off, SEPARATE, ALL
NoAsgn:------,
PM GRP2
CAM001:PRE001 to CAM100:PRE100
11. PM GRP2 10/10
12. PM GRP2 ALL
1. PM GRP3 MODE
2. PM GRP3 1/10
3. PM GRP3 2/10
NoAsgn:------
NoAsgn
Off
NoAsgn:------
NoAsgn:------
NoAsgn, PRE001 to PRE100
Off, SEPARATE, ALL
NoAsgn:------,
PM GRP3
CAM001:PRE001 to CAM100:PRE100
11. PM GRP3 10/10
12. PM GRP3 ALL
1. PM GRP4 MODE
2. PM GRP4 1/10
3. PM GRP4 2/10
NoAsgn:------
NoAsgn
Off
NoAsgn:------
NoAsgn:------
NoAsgn, PRE001 to PRE100
Off, SEPARATE, ALL
NoAsgn:------,
PM GRP4
CAM001:PRE001 to CAM100:PRE100
11. PM GRP4 10/10
12. PM GRP4 ALL
1. USER1
2. USER2
3. USER3
NoAsgn:------
NoAsgn
ND1
ND2
ND3
NoAsgn, PRE001 to PRE100
ND1 to 4, SWLINK, BUSCONT,
FASSIST, CAMSEL, TALLY_IP,
CAMINF, POWER OFF,
USER BUTTON
CAM_PINP CTL, CAM_PINP MODE,
CAM_PINP POS
4. USER4
5. USER5
6. USER6
7. USER7
8. USER8
1. CAM1
ND4
SWLINK
BUSCONT
FASSIST
CAMSEL
NoAsign
[36]
[37]
CTRL TYPE
AUTO IP
Serial, Network, NoAsign
100. CAM100
1. AUTO SET
NoAsign
RENEW IP ADR
RENEW IP ADR, KEEP IP ADR,
ALL CLEAR
(*1) “–” indicates a setting saved to the remote camera.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of setting items (menus) (continued)
Button
number
Initial value on
unit (*1)
Menu name
SWAP IP
Setting item
1. CAM1
Remote camera
Setting
[38]
192.168.0.10
100. CAM100
1. CAM1
192.168.0.109
192.168.0.10
[39]
[40]
MANUAL IP
PORT NO
100. CAM100
1. CAM1
192.168.0.109
80
1 to 65535
1 to 65535
100. CAM100
80
[41]
[42]
SW SETUP
1. SW CTL
2. SW IP ADDRESS
1. SWLINK
NoAsign
192.168.000.008
On
Network, NoAsign
SW FUNCTION
Off, On
2. BUSCONT
Off
Off, On
3. BUS
AUX
Off
Off
AUX, PVW, PinP, KEY
Off, On
Off, On
Off, On
4. FOCUS ASSIST
5. CAMERA SELECT
6. TALLY_IP
Off
7. P/T/Z CONTROL
8. CAM INF
CAM
On
CAM, SW, Button Select
Off, On
9. CAMINF_FORMAT
10. CAMINF_CNAME
11. CAMINF_SCENE
12. CAMINF_GAIN
13. CAMINF_SHUTER
14. CAMINF_IRIS
15. CAMINF_FILTER
16. CAMINF_ALARM
1. INPUT1
2. INPUT2
3. INPUT3
4. INPUT4
5. INPUT5
On
On
On
On
On
On
On
On
CAM1
CAM2
CAM3
CAM4
CAM5
NoAsign
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
[43]
SW INPUT
NoAsign, CAM1 to CAM100
6. INPUT6
100. INPUT100
1. TALLY IN1
NoAsign
CAM1
[44]
[45]
TALLY
CAM1 to CAM100
CAM1 to CAM100
10. TALLY IN10
1. CAM OUT1
CAM10
CAM1
GPI OUT
10. CAM OUT10
SAVE MODE
LOAD MODE
DEL MODE
1. INITIALIZE
2. SYSTEM VER
3. PROGRAM VER
4. FPGA VER
1. POWER
CAM10
SETUP
SETUP
SETUP
ALL
[46]
[47]
[48]
[49]
SD SAVE
SD LOAD
SD DELETE
SYSTEM
SETUP, MEM, CAM, LOG
SETUP, MEM, CAM, UPGRADE
SETUP, INIT, MEM, CAM, LOG
ALL, SETUP
V*.**.** (displayed only)
V*.**.** (displayed only)
V*.**.** (displayed only)
ALARM, No ALARM (displayed only)
FAN ALM, P/T ALM,
[50]
ALARM
2. CAM*
FAN ALM+P/T ALM,
No ALARM (displayed only)
101. CAM*
(*1) “–” indicates a setting saved to the remote camera.
A diagonal line indicates a setting that can only be displayed. It cannot be changed.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages
Tracing memory
Indication
When starting up and switching camera groups
Description
Indication
Description
# minutes ## seconds of recording
is still possible for the tracing
memory of CAM##.
CAM## TMEM
#m##s Remained.
Do not operate the PAN/TILT lever
and the ZOOM button because they
are being initialized.
Don't touch
PTZ Lever!
The recording standby state of
tracing memory.
TM##:
Standby Store.
The unit is connecting to the remote
cameras.
Connecting to
cameras
The recording operation wait state of
tracing memory.
TM##:
Waiting Opr.
Recording tracing memory.
TM##: #m##s
Storing.
Operation lock
The recall wait state of tracing
memory.
TM##: #m##s/#m##s
Standby Recall.
Indication
Description
Operation is disabled.
LOCKED!
Recalling tracing memory.
TM##: #m##s/#m##s
Recalling.
(This appears when an operation
is performed while the indicator
of the ENABLE button of the
corresponding area is off.)
The restore standby state of tracing
memory.
TM##: #m##s/#m##s
Standby Restore.
Restoring tracing memory.
TM##: #m##s/#m##s
Restoring.
Writing data to the flash memory in
the unit after recording or restoring
tracing memory.
Please wait
FLASH Accessing.
Preset memory
Indication
Description
The camera group cannot be
switched in TMEM mode.
CAM GRP can't be
changed in TMEM
Preset memory registration has
completed.
CAM### PMEM
STORE COMPLETE
Preset memory deletion has
completed.
CAM### PMEM
DELETE COMPLETE
z A number is displayed instead of “#”
z A number is displayed instead of “#”
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages (continued)
Memory card
IP connection settings
Indication
Indication
Description
No card is inserted.
Description
The entered IP address, default
gateway, subnet mask, or port
number cannot be set.
NO CARD!
Unavailable
network setting.
Initializing.
INITIALIZING...
NOT REMOVE CARD.
Enter a correct value.
⇒ “Network settings of the unit” in
Basics (page 27)
Saving data to the memory card.
Do not remove the memory card.
SAVING...
NOT REMOVE CARD.
The entered IP address is a
duplicate of a connection destination
IP address set for a camera number
or switcher.
7. IP ADDRESS
IP Duplicate!
Reading data from the memory card.
Do not remove the memory card.
LOADING...
NOT REMOVE CARD.
Initializing, saving, or loading is
completed.
COMPLETE.
The entered IP address is a
duplicate of either the IP address of
the unit or a connection destination
IP address for another camera
number or the switcher.
#. CAM###
IP Duplicate!
The memory card is write protected.
WRITE PROTECTED!
OVER 99FILES!
Saving is not possible because
there are already 99 files.
Saving is not possible because
there is insufficient free space in the
memory card.
INSUFFICIENT
CAPACITY!
The entered IP address is a
1. IP: SW
IP Duplicate!
duplicate of either the IP address of
the unit or a connection destination
IP address set for a camera number.
A file cannot be read by the unit
or selected remote camera. The
following files are incompatible.
z A file saved with a different model
than the currently selected remote
camera.
LOAD FILE
IMCOMPATIBLE!
The unit needs to be rebooted.
Turn the unit’s power off and then
back on.
Please reboot
AW-RP120
z A file containing corrupted data
z A number is displayed instead of “#”
z A number is displayed instead of “#”
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
[49] SYSTEM
1. INITIALIZE ................................................................................ 42
xxMenu
[21] SHUTTER
[50] ALARM ......................................................................................... 40
1. SHUTTER ................................................................................... 9
2. SPEED ........................................................................................ 9
[22] ND FILTER ................................................................................... 11
xxA
[23] FUNCTION
ABB button ............................................................................................ 8
ATW button ............................................................................................ 8
Auto IP setting ..................................................................................... 49
AWB button ........................................................................................... 7
2. DEFROSTER ............................................................................ 26
3. WIPER ...................................................................................... 26
4. HEATER/FAN ........................................................................... 26
[24] CAMERA SETUP
1. CAM POWER ......................................................................... 4, 5
2. AUTO ON .................................................................................... 4
3. TALLY OUT ............................................................................... 39
4. HOME POSITION ..................................................................... 26
xxB
BARS button .......................................................................................... 9
B GAIN dial ............................................................................................ 8
B PED dial ............................................................................................. 8
[25] RP SETUP
1. FOCUS/IRIS ............................................................................. 29
2. P/T CURV ................................................................................. 22
3. LCD BACKLIGHT ..................................................................... 29
4. ENABLE BUTTON .................................................................... 28
5. MENU CONTROL ..................................................................... 28
xxC
CAMERA OSD button .......................................................................... 12
Color adjustment ENABLE button ................................................... 6, 27
Color adjustment section ....................................................................... 6
[26] PAN DIRECTION .......................................................................... 23
[27] TILT DIRECTION .......................................................................... 23
[28] ZOOM DIRECTION ...................................................................... 23
[29] FOCUS DIRECTION .................................................................... 24
xxD
DETAIL button ....................................................................................... 9
[30] PTZ ADJUST
1. Z MIN SPEED ........................................................................... 24
2. SPEED WITH Z ........................................................................ 24
3. LIMIT UP ................................................................................... 25
4. LIMIT DOWN ............................................................................ 25
5. LIMIT LEFT ............................................................................... 25
6. LIMIT RIGHT ............................................................................ 25
xxF
FOCUS SPEED dial ............................................................................ 22
FOCUS/ZOOM/IRIS ENABLE button .................................................. 27
xxG
[31] PM GRP1
GAIN button ........................................................................................... 7
1. PM GRP1 MODE ...................................................................... 16
2. PM GRP1 1/10 .......................................................................... 16
3. PM GRP1 2/10 .......................................................................... 16
11. PM GRP1 10/10 ...................................................................... 16
12. PM GRP1 ALL ........................................................................ 17
xxL
LAN connector ..................................................................................... 44
[35] USER BUTTON ............................................................................ 30
xxM
[42] SW FUNCTION
MEM ENABLE button .............................................................. 13, 18, 27
1. SWLINK .................................................................................... 31
2. BUSCONT ................................................................................ 32
3. BUS .......................................................................................... 32
4. FOCUS ASSIST ........................................................................ 33
5. CAMERA SELECT .................................................................... 33
6. TALLY_IP .................................................................................. 34
7. P/T/Z CONTROL ...................................................................... 34
8. CAM INF ................................................................................... 35
9. CAMINF_FORMAT ................................................................... 35
10. CAMINF_CNAME ................................................................... 35
11. CAMINF_SCENE .................................................................... 35
12. CAMINF_GAIN ....................................................................... 35
13. CAMINF_SHUTER ................................................................. 35
14. CANINF_IRIS ......................................................................... 35
15. CAMINF_FILTER .................................................................... 35
16. CAMINF_ALARM .................................................................... 35
xxP
PAN/TILT ENABLE button ................................................................... 27
PAN/TILT SPEED dial .......................................................................... 22
PED dial ................................................................................................. 7
PMEM button ....................................................................................... 13
PM GRP 1 button ................................................................................ 17
PM GRP 2 button ................................................................................ 17
PM GRP 3 button ................................................................................ 17
PM GRP 4 button ................................................................................ 17
xxR
REMOTE ............................................................................................. 44
Remote camera ..................................................................................... 2
R GAIN dial ............................................................................................ 8
R PED dial ............................................................................................. 8
[43] SW INPUT .................................................................................... 31
[44] TALLY ........................................................................................... 39
[45] GPI OUT
1. CAM OUT1 ............................................................................... 44
[46] SD SAVE ...................................................................................... 37
[47] SD LOAD ...................................................................................... 38
[48] SD DELETE ............................................................................ 37, 38
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Index (continued)
xxS
SCENE 1 button .................................................................................. 10
SCENE 2 button .................................................................................. 10
SCENE 3 button .................................................................................. 10
SCENE 4 button .................................................................................. 10
Setup Software .................................................................................... 45
SHIFT button ................................................................................. 10, 17
xxT
TALLY/GPI ........................................................................................... 43
TMEM button ....................................................................................... 18
TO PAN/TILT HEAD 1 to 5 connectors ................................................ 44
Tracing memory operation section ...................................................... 18
xxU
USER button ........................................................................................ 30
USER ENABLE button .................................................................. 17, 27
xxW
WHITE BAL A button ......................................................................... 7, 8
WHITE BAL B button ......................................................................... 7, 8
xxZ
ZOOM SPEED dial .............................................................................. 22
59
Download from Www.Somanuals.com. All Manuals Search And Download.
プロフェッショナルAVビジネスユニット
〒 571-8503 大阪府門真市松葉町 2 番 15 号
(06) 6901－1161
☎
©Panasonic Corporation 2013
Download from Www.Somanuals.com. All Manuals Search And Download.
|