OWNER'S MANUAL
127CM CORDLESS REMOTE PLASMA TELEVISION & MONITOR
MODEL: PDP5010
N111
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
WARNING: TO REDUCE THE RISK OF OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within
an equilateral triangle is intended to alert the user
to the presence of insinuated dangerous voltage
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of ,important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
(America only)
This product utilises tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please contact
FCC STATEMENT (America only)
FCC Notice
PDP TV: A CLASS B digital device
This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC CAUTION:
Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications to this monitor not
expressly approved by the manufacturer could cause harmful interference and would void the user's
authority to operate this device.
WARNING: This is a CLASS B product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures to counter interference.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent potential danger, please observe
the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service
life of your PDP TV product, please read the following precautions carefully before using the product.
1. Read these instructions---All operating instructions must be read and understood before the product is operated.
2. Keep these instructions---These safety and operating instructions must be kept in a safe place for future reference.
3. Heed all warnings---All warnings on the product and in the instructions must be observed closely.
4. Follow all instructions---All operating instructions must be followed.
5. Do not use this apparatus near water---for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near swimming
pool, and the like.
Do not use immediately after moving from a low temperature to high
temperature environment, as this causes condensation, which may result in
fire, electric shock, or other hazards.
6. Clean only with dry cloth---Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
7. Ventilation---Do not block any ventilation openings. Install in accordance
with the manufacturer instructions. The vents and other openings in the cabinet
are designed for ventilation. Do not cover or block these vents and openings
since insufficient ventilation can cause overheating and/or shorten the life of
the product. Do not place the product on a bed, sofa, rug or other similar
surface, since they can block ventilation openings. This product is not designed
for built-in installation; do not place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is provided or the manufacturer's
instructions are followed.
8. Heat sources---Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Grounding or Polarisation---Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised
plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet. (America only)
10. Power cord protection---Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Attachments---Only use attachments/ accessories specified by the manufacturer. Do not use attachments not
recommended by the manufacturer. Use of improper attachments can result in accidents.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
12. Stand---Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. Do not place the product on an unstable
trolley, stand, tripod or table. Placing the product on an unstable base can cause the
product to fall, resulting in serious personal injuries as well as damage to the product.
When mounting the product on a wall, be sure to follow the manufacturer's instructions.
Use only the mounting by the hardware recommended manufacturer.
13. Carefully move---When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. Sudden stops, excessive force and uneven
floor surfaces can cause the product to fall from the trolley.
14. Lightning---Unplug this apparatus during lightning storms or when unused for long
of periods time.
For added protection for this television equipment during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
15. Servicing---Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. Replacement parts---In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer, or those with the same characteristics and performance as the
shock and/or original parts. Use of unauthorised parts can result in fire, electric other danger.
17. Overloading---Do not overload wall outlets, extension cords, or convenience receptacles on other
equipment as this can result in a risk of fire or electric shock.
18. Entering of objects and liquids---Never insert an object into the product through vents or openings. High voltage
flows and/or in the product, and inserting an object can cause electric shock short internal parts. For the same reason,
do not spill water or liquid on the product.
19. Damage, requiring service---If any of the following conditions occurs unplug the power cord from the AC outlet, and
repairs. request a qualified service person to perform
a. When the power cord or plug is damaged.
b. When a liquid is spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not
described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician.
e. If the product has been dropped or the cabinet has been damaged in any way.
f. When the product displays an abnormal condition or exhibits a distinct change in performance. Any noticeable
abnormality in the product indicates that the product needs servicing.
20. Safety checks---Upon completion of service or repair work, request the service technician to perform safety
checks to ensure that the product is in proper operating condition.
21. Wall or ceiling mounting---When mounting the product on a wall or ceiling, be sure to install the product according
to the method recommended by the manufacturer. This is a safety feature.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
22. Power source---This product is intended to be supplied by a listed power supply indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your product dealer or local power company. For added
protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line
surges. When the unit has to be used with another power supply voltage, the power cable must be changed. Consult your
product dealer. The socket outlet should be installed near the equipment and easily accessible. Use only the power cord
designated by our dealer to ensure safety and EMC. When connecting other products such as VCRs and personal computers,
you should turn off the power of the unit for protection against electric shock.
23. Panel protection---The PDP panel used in this product is made of glass.
Therefore, it can break when the product is dropped or impacted upon by other
objects. Be careful not to be injured by broken glass pieces in case the PDP panel breaks.
24. Pixel defect---The PDP panel is a very high technology product, giving you finely detailed pictures. Occasionally,
a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not
affect the performance of your product.
If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to
provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical
Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode. (America only)
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC---NATIONAL ELECTRICAL CODE
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can collide with
such power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Antenna Connection
INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on
the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing.
Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used
The exact type and position of the aerial will depend upon your particular area.
.
Note:
It is recommended that the 75-ohm coaxial
cable be used to eliminate interference and
noise that may occur due to radio wave
conditions.
The aerial cable should not be bundled
with the power cord and the like.
Speaker Connection
Connect the speaker audio cable to the
external speaker output jack on the unit
matching the "+" and "-" ends of the cable.
(Black)
(Red)
(Black)
(Red)
Note:
1. Unplug the plasma display and all connected
components before connecting the Speakers.
2. The illustration may be different depending on
model.
SPEAKER
Power Connection
Plug into AC outlet
AC-INPUT
Household
power outlet
AC cord
1. Connecting the female plug to the AC socket on the unit.
2. Connecting the male plug to the wall outlet as illustrated.
Note:
This product should be operated only from the type of power source indicated on the marking label.
Always unplug the AC cord from power outlet when not using for a long period of time.
The illustration of the AC plug is for your reference only.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
6
3
4
7
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls
Main Unit
2
1
3
5
6
7
8
9
10
11
4
12
Speaker output jacks
RS232 control interface
1
2.
For service only. The user cannot operate the unit through the RS232 terminals.
HDMI input
3.
To connect with those equipments with HDMI interface, for example, Set-top box or DVD player.
D-Sub interface/Audio in
Connect with those equipments with D-Sub interface, for example, PC.
4.
Connect the audio jacks as well with audio cable.
Component inputs 1
5.
Connect to the audio and component output jacks of a DVD player or Set-Top Box.
Component inputs 2
6.
Connect to the audio and component output jacks of a DVD player or Set-Top Box.
AV outputs
7.
Connect to the VCR input jacks to record programs.
S-Video input
8.
Receive a S-Video signal from external source such as VCR or DVD player.
AV inputs 1
9.
Receive a video/audio signals from external sources such as VCR or DVD player.
AV inputs 2
10.
11.
12.
Receive a video/audio signals from external sources such as VCR or DVD player.
Antenna input
Allow you to connect cable or outdoor antenna.
AC power input
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
Descriptions for the button functions
This button has no function
1. POWER
Turn the unit on or off
2. 0-9 Buttons
Direct channel select
3.
button
To select channel digit.
button
4.
To quickly jump between current channel and last selected channel.
5. S-SYS
To set sound system
6. C-SYS
To set colour system
7. LIST
To display the supported format list in D-SUB, HDMI or Component
input mode.
8. ADJUST
To rectify the picture automatically in VGA mode
9. AUDIO
To select sound mode
10. PICTURE
To select picture mode
11. SLEEP
To set sleep timer
12. INFO
To display current status information
13. MUTE
Sound mute
14. INPUT
To access Input Select menu
15. FREEZE
To freeze current picture
16. MENU
To access the MENU main page
17.
Menu navigators in menu operations
18. ENTER
To confirm your operation or setting or access the submenu
19. CHANNEL +/-
To switch channels
20. VOLUME +/-
To adjust volume
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Cautions Before Connecting
Carefully check the terminals for position and type before making any connections.
The illustration of the external equipment may be different depending on your model.
Loose connectors can result in image or colour problems. Make sure that all connectors are securely inserted
into their terminals.
Refer to the operating manual of the external device as well.
When connecting an external device, turn the power off on the panel to avoid any issues.
Connect AV1 Input Terminals
INPUT SELECT
D-SUB
HDMI
TV
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on
the unit and the video player.
For better video, you can use the S-video jack if your source supports it.
The S-video shares the same audio terminals with video terminal.
To view the program from the AVI input terminals, please select AV1 (or
S-VIDEO when using s-video jack) in the INPUT SELECT menu after
proper connection.
AV 1
AV 2
S-VIDEO
HDTV 1
HDTV 2
Y
Yellow (video)
White (audio L)
Red (audio R)
W
R
Video player
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connect AV2 Input Terminals
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on
the unit and the video camera.
INPUT SELECT
D-SUB
HDMI
TV
AV 1
To view the program from the AV2 input terminals, please select AV2 in
the INPUT SELECT menu after proper connection.
AV 2
S-VIDEO
HDTV 1
HDTV 2
Y
Yellow (video)
W
White (audio L)
R
Red (audio R)
Video camera
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connect AV Output Terminals
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR.
To record the desired program, please select a program you wish to record firstly, then turn on your VCR,
insert videotape for recording and press the Record button to begin recording.
Note: The AV output terminals output the audio/video signal from the Antenna input or AV inputs.
Y
Yellow (video)
W
White (audio L)
R
Red (audio R)
VCR for recording
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connect Component Input Terminals
Connect the component video cable between the component input jacks on the unit
and component output jacks on the video player, for example, DVD player or Set-top
box.
INPUT SELECT
D-SUB
HDMI
TV
AV 1
AV 2
Connect the Audio cable between the audio input jacks on the unit and audio output
jacks on the video player.
To view the program from component terminals, please select HDTV1 or HDTV2 in
the INPUT SELECT menu according to your connection.
S-VIDEO
HDTV 1
HDTV 2
White (audio L)
Red (audio R, Cr/Pr)
Green (Y)
Blue (Cb/Pb)
Video Player
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connect the HDMI Interface
Connect the HDMI cable between the HDMI interface on the unit and the HDMI
output interface on the video equipment.
INPUT SELECT
D-SUB
HDMI
TV
AV 1
To view the program from the HDMI interface, please select HDMI in the INPUT
SELECT menu after proper connection.
Note:
AV 2
The HDMI Sources are compatible with DVI displays through the use of a passive
cable converter. So you may connect product with DVI output jack to the unit.
Connect a passive cable converter between the HDMI input jack on the unit and
DVI jack on the product. Connect an Audio cable between the AUDIO output on
your product and AUDIO input jack of D-SUB IN on the unit.
S-VIDEO
HDTV 1
HDTV 2
Video equipment with
HDMI interface
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connect the D-SUB Interface
Connect the D-SUB cable between the D-SUB interface on the unit and the D-SUB
output interface on the video equipment or PC.
INPUT SELECT
D-SUB
HDMI
TV
AV 1
Connect the Audio cable between the audio input jacks on the unit and audio output
jacks on the video player or PC.
To view the program from the D-SUB interface, please select D-SUB in the INPUT
SELECT menu after proper connection.
AV 2
S-VIDEO
HDTV 1
HDTV 2
D-SUB cable
Audio cable
PC or Video equipment
with D-SUB interface
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Turning the Unit On and Off
Turning On
Insert the power cord into the wall outlet. Press the power switch to power on.
If the unit is in STANDBY mode, please press the POWER
button to turn on the unit.
Turning Off
With the power on, press the Power
button to turn off.
If you would like to cut off the power completely, press the power switch directly.
Viewing the MENU
Your PDP TV has a simple, easy-to-use menu system that appears on the
screen. This system makes it convenient and fast to use features on the unit.
The unit also lets you display the status of many of your PDP TV features.
PICTURE
Brightness
65
50
50
Contrast
Color
With the power on, press the MENU button on the remote control. The
main menu appears on the screen.
Use
to select submenu item. Use the ENTER or
to access
Sharpness
3
the selected submenu page.
Use
selected item. Also use the ENTER
Warm
Personal
Color Temp.
Picture Mode
to select menu items and the
to adjust the value of the
or to confirm your settings or
access the sub pages. Those items that are unnecessary to adjust
cannot be selected
During menu operations, use the MENU button to return to the parental menu or exit the menu operations.
Note:To clearly introduce the menu operations, this operating manual provides a description based on
operation with the remote control.
Select Input Signal Source
INPUT SELECT
Press the INPUT button to display the INPUT SELECT menu.
D-SUB
Press
to select the desired input source.
HDMI
TV
AV 1
Press ENTER to confirm.
Note: the last input source will be memorised when the unit is turned off.
AV 2
S-VIDEO
HDTV 1
HDTV 2
Displaying Status Information
Press the INFO button on the remote control, the unit displays current status information such as channel
number, signal source, etc.
Displaying Supported Formats
Press the LIST button on the remote control, the unit displays all formats supported by this unit in current mode.
The button may not work in some modes, for example, in TV mode.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Changing Channels
Using the Channel Buttons (CH+ or CH-)
Press the CH+ or CH- to change channels.
When you press the CH+ or CH-, the unit changes channels in sequence. You will see all the channels
that the unit has memorised.
You will not see channels that were erased.
Direct Accessing Channels
Press the number buttons to go directly to a channel.
To select a one-digit channel: press the 1-9 number buttons to input the channel number and the unit
goes to the selected channel.
To select a two-digit channel: press the
button to display - -, press the 0-9 number buttons to input
the channel number and the unit goes to the selected channel.
To select a three-digit channel: press the
button to display - - -, press the 0-9 number buttons to
input the channel number and the unit goes to the selected channel.
Note: There are some other methods to select by using the 0-9 number buttons.
When you use the number buttons, you can directly select those channels that were skipped.
Using the Return
button
Press this button to switch between the current channel and the previous channel.
Adjusting the Volume
Using the volume buttons (VOL+ and VOL-)
Press the VOL + or VOL- to increase or decrease the volume.
Using the MUTE button
At any time, you can temporarily cut off the sound using the MUTE button. To turn mute off, press the
MUTE button again.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorising the Channels
Your PDP TV can memorise and store all the available channels. After the available channels are memorised,
use CH+/- to scan the channels.
Storing Channels in Memory Automatically
CHANNEL
Press MENU to display the menu main page.
Press repeatedly to select CHANNEL item.
Press ENTER or to access the submenu.
Channel Edit
Auto Search Right to select
Press
Press
repeatedly to select Auto Search item.
to start the process of auto searching. The unit stores all
Manual Search
Skip
L/R to select
OFF
available channels in memory automatically.
AFC
ON
During the process of the Auto Search, you can press MENU to exit.
Fine Tune
+00
Note: Before you start Auto Search, please refer to the section of [Setting
Colour and Sound System] to select a proper sound system according
to your area.
Storing Channels in Memory Manually
Use Manual Search if desired channels cannot be memorised or if you would
like to store channels to specific channel numbers one by one.
CHANNEL
Channel Edit
Auto Search
Press MENU to display the menu main page.
Right to select
Press
Press ENTER or
repeatedly to select CHANNEL item.
to access the submenu.
Manual Search L/R to select
Skip
OFF
ON
Press
Press
repeatedly to select Manual Search item.
start manual search.
AFC
Fine Tune
+00
Pressing
Pressing
the set searches towards higher frequency;
the set searches towards lower frequency;
The search stops when a program is found and this program will be
stored in current channel.
Setting Auto Frequency Control (AFC)
Press MENU to display the menu main page.
CHANNEL
Press
Press ENTER or
repeatedly to select CHANNEL item.
to access the submenu.
Channel Edit
Auto Search
Manual Search
Skip
Right to select
L/R to select
OFF
Press
Press
repeatedly to select AFC item.
to select ON or OFF.
When the AFC is set to ON, the unit will automatically tune the program
frequency to provide the best possible picture and sound.
AFC
ON
Fine Tune
+00
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorising the Channels
Manual Fine Tuning
Press MENU to display the menu main page.
Press repeatedly to select CHANNEL item.
Press ENTER or to access the submenu.
CHANNEL
Channel Edit
Auto Search
Manual Search
Skip
Right to select
L/R to select
OFF
Press
repeatedly to select Fine Tune item.
Press
to fine tune till the best possible picture and sound are
obtained.
AFC
ON
If you fine tune a program manually, the AFC will be turned off
automatically.
Fine Tune
+00
Adding and Erasing Channels
Press MENU to display the menu main page.
CHANNEL
Press
Press ENTER or
repeatedly to select CHANNEL item.
to access the submenu.
Channel Edit
Auto Search
Manual Search
Skip
Right to select
L/R to select
OFF
Press
Press
repeatedly to select Skip item.
to select ON or OFF.
When the item is set to ON, the selected channel will be erased.
When the item is set to OFF, the selected channel will be added.
The erased channels cannot be selected by using the CH+/- buttons
unless you use number buttons to input channel number directly.
AFC
ON
Fine Tune
+00
Setting Colour and Sound System
Press MENU to display the menu main page.
OPTION
Press
repeatedly to select OPTION item.
Video Format
PAL
Press ENTER or
to access the submenu.
Audio Format
BG
Press
Press
to select Video Format item.
to select a proper colour system.
Normally, this item is set to AUTO.
Press
Press
to select Audio Format item.
to select a proper sound system according to your area's
broadcasting system.
Note: You may use the C-SYS button to quickly select the color system;
You may also use the S-SYS button to quickly select the sound system.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing Channels
Editing Channel Number
You may use this function to arrange the channel order as your will.
Press MENU to display the menu main page.
CHANNEL
Press
Press ENTER or
Press to select Channel Edit item.
If the Channel Edit is highlighted automatically, this step can be skipped
Press ENTER or to access the sub page.
Press to select Channel Number Edit item.
repeatedly to select CHANNEL item.
Channel Edit
to access the submenu.
Auto Search
Manual Search
Skip
Right to select
L/R to select
OFF
.
AFC
ON
Fine Tune
+00
If the Channel Number Edit is highlighted automatically, this step can
be skipped.
Press ENTER or to access the sub
page.
In the channel number editing page,
CHANNEL
Channel Number Edit
Current Channel Num
Current Channel Name
004
Channel Name Edit
use
to move the cursor; use
to select a target channel that is
to exchange contents with current
channel. Use ENTER to confirm or
MENU to return.
005
Edit Channel Number
Left / right key to move cursor
Up / down to change channels
Select to Edit / menu to Exit
Editing Channel Name
You may use this function to edit the channel name as your will.
CHANNEL
Channel Number Edit
From the channel editing sub page, press
Name Edit item.
to select Channel
Channel Name Edit
Press ENTER or to access the sub page.
In the channel name editing page, use
to move the cursor; use
to change name. Use INPUT to clear or MENU to return.
Current Channel Num
004
Current Channel Name TV1
TV1
Edit Channel Name
left / right key to move cursor
up / down to change name
source to clear label
menu to Exit
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Picture
Setting Picture
PICTURE
Press MENU to display the menu main page.
Press repeatedly to select PICTURE item.
Press ENTER or to access the submenu.
Brightness
Contrast
Color
65
50
50
Press
Press
to select menu item that you would like to adjust.
to adjust the value of the selected item.
Sharpness
3
Warm
Personal
Color Temp.
Picture Mode
As an example, the right illustration is the PICTURE menu page in
TV mode.
Descriptions
Notes
Item
The Tint is for NTSC
only.
The menu items may
be different when the
unit works in different
Press
to adjust screen brightness for easier viewing of
Brightness
dark picture such as scenes and black hair.
Press
Press
Press
to adjust image contrast.
to adjust image colour saturation.
to adjust the skin tone.
Contrast
Color
mode For example,
.
the Frequency and
Phase items may be
unavailable in TV and
AV mode.
Some items display in
grey and you will find
that they cannot be
selected. In this case,
these items are
unnecessary to adjust.
The unit allows you to
customise the color
temperature in VGA
mode only.
You may press the
PICTURE button to
quickly select a
Tint
Press
Press
Press
Press
to adjust the image sharpness.
Sharpness
Color Temp.
Picture Mode
to select colour temperature setting for the image.
to select a desired picture mode.
to adjust the image frequency. Adjust the clock
frequency of the set's internal clock signal. If shimmering or
rainbow-like noise is apparent in the image, try adjusting the
clock frequency setting.
Frequency
Phase
Press
to adjust the image phase. You may find that
images blur, depending on the clock phase of your PC's
Processor. If you experience blurring, you can obtain a clearer
image by adjusting the phase setting.
desired picture mode.
Customising Colour Temperature
PICTURE
With working in VGA mode, press
the PICTURE menu page.
to select Color Temp item in
Red
20
Green
Blue
20
Press
Press
Press
to select User and press ENTER to access the sub page.
to select Red, Green or Blue item.
to adjust the value until the colour temperature is satisfied.
200
Press MENU to return or exit.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Sound
Setting Sound
SOUND
Press MENU to display the menu main page.
Press repeatedly to select SOUND item.
Press ENTER or to access the submenu.
Volume
Balance
Treble
Bass
20
+00
+00
Press
Press
to select menu item that you would like to adjust.
to adjust the value of the selected item.
+00
Sound Mode
Surround
Personal
OFF
ON
Notes
Item
Volume
Balance
Treble
Descriptions
Press
Press
Press
Press
Press
Press
to adjust the volume.
The menu items may be
different when the unit
works in different mode.
to adjust the sound balance.
to adjust treble sound effect.
to adjust bass sound effect.
to select a desired sound mode.
to turn on or off this effect.
You may press the
Audio button to quickly
select a desired sound
mode.
Bass
Sound Mode
Surround
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting System
Setting System
SETTING
Press MENU to display the menu main page.
Press repeatedly to select SETTING item.
Press ENTER or to access the submenu.
Press
OSD Setting
TIME Setting
3D Comb Filter
Screen Saver
ON
ON
OFF
OFF
to select menu item that you would like to adjust.
Reset All Value, Right To Select!
Descriptions
Item
OSD Setting Refer to chapter [Setting On-Screen Display].
Refer to chapter [Setting Time].
TIME setting
3D Comb Filter
Screen Saver
Reset
Press
Press
to turn on or off 3D Comb Filter.
to turn on or off screen saver.
Press to reset all value to default.
Setting On-Screen Display
From the SETTING submenu page, Press
Press ENTER or to access the sub page.
repeatedly to select OSD Setting item.
Press
to select menu item that you would like to adjust.
SETTING
Descriptions
Item
OSD Language
ENGLISH
OSD Language Press
Press
to select a proper OSD language.
OSD Skin
Main
Sub
20
OSD Trans.
OSD Time Out
to select Main or Sub, which means you
would like to adjust the skin of the main menu or
submenu. Press ENTER to access sub page.
OSD Skin
15
Press
to adjust the OSD transparency.
OSD Trans.
Press
to set the time that how long the OSD
OSD Timeout
displays on the screen without any operation.
Setting Menu Skin
From the OSD SETTING sub page, Press
repeatedly to select OSD Skin item.
Press ENTER to access the sub page to set menu skin.
Press
Press
repeatedly to select item.
to adjust the item's value or press ENTER to confirm your operation.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting System
Setting Time
Press MENU to display the menu main page.
Press repeatedly to select SETTING item.
Press ENTER or to access the submenu.
Press to select TIME Setting item.
Press ENTER or to access the time setting sub page.
Press
to select item to adjust.
SETTING
SETTING
SETTING
Sleep Timer
OFF
16:00
OSD Setting
TIME Setting
3D Comb Filter
Screen Saver
Sleep Timer
Current Timer
OFF
--:--
Current Timer
Auto Power Off
Auto Power On
ON
ON
OFF
OFF
22:00
18:00
Reset All Value, Right To Select!
Item
Descriptions
Press
to set sleep timer.
Sleep Timer
You may also use SLEEP button to quickly set sleep timer.
Current Timer
Press
to move the cursor, use 0-9 buttons to input time.
This item cannot be accessed until you finish setting current timer.
Press to move the cursor, use 0-9 buttons to input time.
If you would like to cancel this function after setting, press repeatedly until
OFF appears.
Auto Power Off
Auto Power On
This item cannot be accessed until you finish setting current timer.
Press
to move the cursor, use 0-9 buttons to input time.
If you would like to cancel this function after setting, press repeatedly until
OFF appears.
Note:
If you have set the timer of Auto Power On, once you perform turn-on operation ahead of the preset
time, the Auto Power On setting will be cancelled.
If you have set the timer of Auto Power Off, once you perform turn-off operation ahead of the preset
time, the Auto Power Off setting or sleep timer setting will be cancelled.
Once the Auto Power On, Auto Power Off or sleep timer function is executed, these functions need
to be reset again if you would like to use these functions.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Window
Setting Window
WINDOW
Image Size
4:3 ASP
30
Press MENU to display the menu main page.
Press repeatedly to select WINDOW item.
Press ENTER or to access the submenu.
H Position
V Position
17
Press
Press
to select menu item that you would like to adjust.
to adjust the value of the selected item.
Freeze Window
ON
OFF
As an example, the right illustration is the WINDOW menu page in TV mode.
Descriptions
Item
Notes
Image Size
H Position
V Position
H Width
Press
Press
Press
Press
Press
to select a proper image size.
Some items display in
grey and you will find
that they cannot be
selected. In this case,
these items are
to adjust horizontal position for current image.
to adjust vertical position for current image.
to adjust horizontal width for current image.
to adjust vertical width for current image.
unnecessary to adjust.
You may also use the
ADJUST button to
quickly perform auto-
adjustment.
V Width
With working in component input mode or VGA mode, if the
image displays abnormally, press perform auto-adjustment.
The unit automatically adjusts phase, clock or position, etc.
Auto Adjust
You may also use the
FREEZE button to
quickly freeze current
image
Press
to select On or Off to freeze current image or
Freeze Window
cancel freezing function.
Important Cautions:
1. For the sake of protecting the screen, please DO NOT freeze an image for a long time.
2. To avoid the brightness dissonance between the screen centre and the screen edges,
please do not use 4:3 mode for a long time.
3. If you are watching programs from DVD or VCR equipment, when the program has been
finished, some player device may display its logo on the screen. Displaying this kind of static
logo may damage the screen, please turn off the player equipment in time.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before calling for repair service, check the following items for possible remedies to an
encountered symptom.
Symptoms
Check item
"Ghost" or double images
This may be caused by obstruction to the antenna due to high rise buildings
or hills. Using a highly directional antenna may improve the picture.
No power
No picture
Check that the AC power cord is plugged into the mains socket.
Unplug the power cord, wait for 60 seconds. Then reinsert plug
into the mains socket and turn on the unit again.
Check antenna connections at the rear of the unit to see if it is
properly connected to the unit.
Possible broadcast station trouble. Try another channel.
Adjust the contrast and brightness settings.
Select a correct input.
Is a non-compatible signal being input?
Increase the VOLUME.
Good picture but no sound
Check that the unit is not muted.
Good sound but poor colour
Poor picture
Adjust the contrast, colour and brightness settings.
Sometimes, poor picture quality occurs when having activated an S-VHS
camera or camcorder connected and having connected another peripheral
at the same time. In this case, switch off one of the other peripherals.
Check whether the room is too bright.
This may be caused by electrical interference (e.g. hair dryer,
nearby neon lights, etc.)
Horizontal dotted line
Turn off the equipment.
Check whether the batteries are working. Replace if necessary.
Clean the remote control sensor lens on the unit.
Television not responding to
remote control
Do not use the remote control under strong or fluorescent lighting.
The batteries should be inserted with polarity (+, -) aligned.
Snowy picture and noise
Check the antenna connection.
No stable or not
synchronised D-Sub picture
Check if you have selected the correct D-Sub mode in your PC.
Adjust Balance in the SOUND (AUDIO) menu.
No output from one
of the speakers
Control buttons do not work
Unplug the power cord, wait for some seconds. Then re-plug the
power cord and turn on the unit again.
Note:
If your problem is not solved, restart your TV by turning it off and then on again once.
Never attempt to repair a defective TV yourself.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
Do not use in hot or cold rooms (locations)
When the unit is used in rooms (locations) with low temperature, the picture may leave trails or appear
slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct
sunlight or near a heater, as this may cause the cabinet to deform and the PDP panel to malfunction.
(Storage temperature: 0°C to +50°C
Working temperature: 5°C to +40°C)
PDP Display Panel
Symptoms
Check item
The plasma display panel is manufactured using an extremely high
level of precision technology, however, sometimes some parts of
the screen may be missing picture elements or have luminous spots.
This is not a malfunction.
Some parts of the screen do not
light up.
Do not allow a still picture to be displayed for an extended period,
as this can cause a permanent after-image to remain on the
Plasma Display.
After-images appear
Examples of still pictures include logos, video games, computer
images, teletext and images displayed in 4:3 mode.
Note:
The permanent after-image on the Plasma Display resulting from
fixed image use is not an operating defect.
This product is not designed to display fixed images for extended
periods of time.
Snapping sounds may be heard from
the display unit.
This sound is produced when the cabinet expands or contracts due
to variations in temperature and is not a malfunction.
Cleaning and Maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using
only a cleaning cloth or a soft, lint-free cloth.
If the surface is particularly dirty, soak a soft, lint-free cloth in a weak detergent solution and then wring
the cloth to remove excess liquid. Use this cloth to wipe the surface of the display panel, and then wipe
it evenly with a dry cloth, of the same type, until the surface is dry.
Do not scratch or hit the surface of the panel with fingernails or other hard objects. Furthermore, avoid
contact with volatile substances such as insect sprays, solvents and thinner; otherwise the quality of the
surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
If the cabinet is particularly dirty, soak the cloth in a weak detergent solution and then wring the cloth dry.
Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
Do not allow any detergent to come into direct contact with the surface of the Plasma Display.
If water droplets get inside the unit, operating problems may result.
Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the. quality
of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave
it for long periods in contact with articles made from rubber or PVC.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
604-PS50T183-00
Ver. 1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|