Palsonic DVD Recorder DVDR160G User Manual

INSTRUCTION MANUAL  
DVD RECORDER  
DVDR160G DVD & HDD  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
(Please read this manual before  
installation and operation)  
ENGLISH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety  
Important Safety Instructions:  
* Read these instructions.  
* Keep these instructions.  
* Heed all warning.  
* Follow all instructions.  
* Do not use this apparatus near water.  
* Clean only with dry cloth.  
* Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.  
* Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
* Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised plug has two  
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.  
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into  
your outlet, consult an electrician for replacement of the obsolete outlet.  
* Protect the power cord from being walked on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the apparatus.  
* Only use attachments/accessories specified by the manufacturer.  
* Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with  
the apparatus. When a cart is used, use with caution when moving the cart/apparatus combination to  
avoid injury from tip-over.  
* Unplug this apparatus during lightning storms or when unused for long periods of time.  
* Refer all servicing to qualified service personnel. Servicing is required when the apparatus has  
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or  
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not  
operate normally, or has been dropped.  
* Read through this instruction manual before installation and use.  
* To disconnect the power cord, hold the plug instead of pulling the cord.  
* Switch off the main power when the unit is not in use. (Disconnect the power plug from the power  
outlet when you do not intend to use the unit for a prolonged period of time.) Before moving the unit,  
remove the disc from the unit's tray first.  
* Do not open the cover or touch any of the components inside the unit.  
* Do not operate or install the unit under direct sunlight or near objects that radiate heat. This may  
lead to overheating of the unit.  
* Do not operate or install the unit in moist or humid conditions. This may affect the pick-up of the unit.  
* Install the unit on a flat surface with good air circulation. Please ensure the ventilation holes are not  
covered otherwise the unit will overheat and malfunction.  
* Wipe the panel and case with soft dry cloth only. Do not apply any kind of thinner, alcohol or sprays  
when cleaning the unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety  
NOTES for CATV erector  
This page which lists correct grounding method and detailed instructions is to remind CATV  
erector of NEC 820-40 parts. Cables should be connected to grounding system of the building.  
If the unit is connected to the antenna outdoor or cable system, the outdoor antenna must be  
grounded to prevent statical disturbance by thunder. National Electronic Code 810 part, US National  
Standardisation Organisation/National Fireproofing Association NO.70-1984 (Canada Electronical  
Code part 1 paragraph 54), this part contains correct grounding method of antenna and building,  
grounding method of lead-in and antenna discharger, and how to connect grounding electrode and  
The request for electrode.  
Do not put the external part of electrical wire near the high voltage wire. When installing antenna  
system, be careful that do not touch or near the high voltage wire or circuit. They might cause mortal  
harm. Installing antenna is very dangerous and should be finished by professionals.  
1.  
2.  
Direction:  
Unplug the unit from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or  
1.  
aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the unit.  
Never let any liquid spattered on the unit. It might cause electric shock or fire hazard.  
Please disconnect the unit under these conditions: lightning, rainstorm, unused for a long time.  
2.  
3.  
Maintain:  
Do not repair the unit yourself. Opening or removing the cover may expose you to dangerous  
1.  
voltage or other hazards. Refer all servicing to qualified service personnel.  
Unplug the unit and apply for professional maintainer in such conditions below:  
A. Power plug or power lead is damaged  
2.  
B .If liquid has been spilled or objects have fallen into the unit  
C. The unit has been exposed to rain or water  
D. If the unit does not operate normally when following the operating instructions.  
E. If the unit has fallen or the cabinet has been damaged  
F. When the unit exhibits a distinct change in performance this indicates a need for service.  
If the technician technician finds the substituted component is equal to original one in safety  
character after inspection, or the manufacturer of substituted component detailed explain that  
this component is considered of anti-fire, anti-electric or anti-other disaster, then this substituted  
component can be used .  
3.  
4.  
The manufacturer note that the maintained unit should be undertake the safe inspection to ensure  
the unit security.  
Please refer to the safety specification if you want install the unit on the wall.  
Please install the unit far away from following items: radiator, oven, and other heating (including  
amplifier).  
5.  
6.  
Note:  
Our company would update the software and function, if there are any difference with practical operation  
with instruction manual, please refer to the unit real function.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Chapter 1: General introduction ---------------------------------------- 01  
Function introduction  
Chapter 2: Operation interface ------------------------------------------ 02-10  
Front panel  
Rear panel  
Connecting to TV  
Connecting to amplifier  
Connecting to outer AV equipment  
Connecting to TV set, recorder, DVB, DVD recorder  
Remote  
Chapter 3: Basic playback ------------------------------------------------  
11-12  
Chapter 4: Menu setup ----------------------------------------------------- 13-17  
Setup - Recording  
Setup - Video  
Setup - Audio  
Setup - Language  
Setup - Date/Time  
Setup - Preferences  
Setup menu - Time-Shift  
Chapter 5: Basic recording ----------------------------------------------- 18-23  
Preparing for recording  
General recording  
Disc operating  
Disc editing  
Setup timing record  
Chapter 6: Additional information -------------------------------------- 24-26  
Usual issues  
Troubleshooting  
Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: General introduction  
Function Introduction  
1 Stereo 2 channel, 5.1 channel analog audio output, coaxial, optical digital output.  
2 HDMI, VGA, CVBS, S-video, YCbCr/YPbPr output.  
3 Analogue signal input (CVBS,L,R); S-Video input.  
4 Y/Cb/Cr signal input, produce clearer recording Video.  
5 Intelligent monitor, can connect with Digital Variscope, shoot and record continuously for 223 hours,  
store real-time monitor information, apply to home monitor and meeting recording etc.  
6 USB input, can play JPEG file, Mp3 music and Mp4 movie in the storage equipment connected to USB jack,  
can also record any file of which to DVD+R/RW, DVD-R/RW disc.  
7 TV signal (RF) input, default 200 TV channels.  
8 Professional recorder driver, can record the content on HDD to DVD±R/RW disc rapidly,  
record one hour's content within 60 seconds without affecting the picture quality, make recoding convenient and fast.  
9 Built-in large capacity HDD (support maximum 160GB HDD), can record TV program DV signal and AUX  
in signal into HDD, to save and play at any time.  
10 6 recording modes, maximum 6 hours disc recording of high quality (4.7GB DVD±R/RW disc),  
up to 223 hours HDD recording.  
11 Intelligent timer recording, miss no wonderful program.  
12 Recording of DVD Video quality, can keep the high video quality of the original program.  
13 Various disc editing and management.  
14 Support modification of TV channel information (including frequency and audio mode.)  
15 Disc lock function, prevent from deleting or recording by mistake.  
16 Disc compatibility processing, make recorded DVD±R/RW disc to be played in other DVD players easily.  
17 Built-in Multi-digital Audio Decoder e.g. Dolby Digital, HDCD„ MPEG4, PCM.  
18 Support Divx/Divx Pro/Xvid, MPEG1, MPEG2, MP3, JPEG decoder.  
19 Support multi-disc format e.g. DVD, DVD±R/RW, SVCD, VCD, CD, CD-R/RW, Picture CD.  
20 Built-in large storage HDD, support copying between sources of HDD-DVD-USB, support super long  
recording, high speed accessing and rewriting.  
21 Adopt MPEG-II digital real time coding & decoding technology of LSI LOGIC American company,  
support multi recording modes.  
22 Special TIME SHIFTING, "PAUSE" "FAST FORWARDS" "FAST BACKWARDS" "SLOW" the TV program,  
won't miss any wonderful moment, Time Shift buffer can be selected (from 60, 180, 360 minutes)  
23 Support OTR (one touch recording) and OTS (one touch stop), recording time can be set, convenient and fast.  
24 Chinese graphic user interface, naming recorded program through built-in Chinese phonetic input,  
make management more convenient.  
25 Special effect playback such as immediate playback of recorded program, playback in slow motion and  
fast forward and fast backwards playback in 32X speed etc., fast program selecting, you can choose as you like.  
26 Strong program management, can delete, protect, name the program (lock HDD) as you like.  
27 Built-in real time clock, even power outage or power disconnection, it can still run accurately and  
ensure scheduled timer recording to start on time.  
28 Support PIP (picture in picture) and dynamic display, support traditional Chinese DIVX subtitle.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Operation interface  
Front panel  
Channel up  
Channel down  
Source  
Receiver window  
Disc tray  
Open/Close  
Record  
Stop  
Play/Pause  
USB socket  
STANDBY  
LED display  
i-link / DV socket  
Video input socket (yellow)  
Left audio input socket (white)  
Right audio input socket (red)  
Rear panel  
put  
YPbPr/YCbCr out  
Antenna Input  
Power ON/OFF  
Coaxial output  
AUDIO output  
VGA output HDMl output  
CVBS  
L
Optical output  
S-Video input  
nd audio  
S-Video output  
Antenna Output  
AUDIO input  
YCbCr input  
5.1 channels surrou  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to TV  
Aerial cable (Essential connection for TV program record)  
Antenna  
HDMI cable  
L
Component cable (Green, Blue, Red)  
Audio cable (white & red)  
Video cable (yellow)  
Yellow (video)  
S-Video cable  
White (L)  
Red (R)  
Green  
Blue  
Red  
Aerial cable (essential connection)  
VGA Cable  
TV set  
Connections  
&
are necessary for TV and recorder to receive TV signal.  
Unlike conventional VCR machine, the recorder will not output its "own"  
signal via the aerial cable. So, it's normal that you cannot view the recorder  
signal from any of the separate TV channels.  
Connecting either one of  
&
,
&
,
&
,
&
or  
is  
necessary for the TV to receive recorder signal.  
Notes  
Connect the player's down mix audio left (L) and right (R) output to the TV's audio left and right inputs.  
Connect either one of the player's video output ( Video, S-Video or component) to the TV's corresponding video input.  
If the TV set is equipped with component video input, connecting this signal will provide the best picture quality.  
1.  
If the TV has VGA input, connect the VGA port of the recorder to that of TV, VIDEO signal output from progressive  
RGB signal.  
2.  
If the TV has more than one video inputs, you may choose either one to connect. Make sure you  
have properly connected the video and audio ports, and switch the TV channel to the same input (e.g. AV1, AV2, .. etc.)  
HDMI jack contains not only digital video signal, but also digital audio signal.  
3.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
L
R
C
Centre  
Front Left  
Front Right  
Subwoofer  
SW  
Surround Left  
Surround Right  
SR  
SL  
L
White  
Red  
L
R
C
Centre  
Front Left  
Front Right  
Subwoofer  
SW  
Surround Left  
Surround Right  
SR  
SL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
L
Download from Www.Somanuals.com. All Manuals Search And Download.  
L
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote  
DISPLAY  
STANDBY  
T-Shift  
SUBTITLE  
AUDIO  
NUMBER KEY  
SETUP  
SOURCE  
DV/USB  
DVD  
HDD/DUB  
ENTER  
EDIT  
ADD/CLEAR  
RETURN  
TIMER  
PAUSE  
PLAY  
STOP  
PREV  
NEXT  
VOLUME  
RECORD  
F.FWD  
F.REV  
CHANNEL  
REVERSE  
REPEAT  
A-B  
FUNC  
SLOW/SORT  
GOTO  
VIDEO OUTPUT MODE  
ZOOM  
PIP  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote  
STANDBY: Stand-by, enter or exit stand-by state.  
DISPLAY: When playing disc, press "DISPLAY" key to display the information of the recorder's  
current state on TV screen.  
(ANGLE: If DVD contains segments viewed from different angles, you can enjoy different viewing  
angel content. Playing multi-angle segment DVD disc, press "ANGLE" to enjoy the content by  
different viewing angles. Note: It is available only when the disc holds this kind of information.)  
OPEN/CLOSE: Open or close the tray door.  
Time-shift: you can only turn ON / OFF time-shift function in AUX in or TV TUNER mode.  
AUDIO: TO switch language or audio. When playing disc with multi-languages or multi-audio.  
press "AUDIO" to switch the languages or audio to play.  
SUBTITLE: TO switch the displaying subtitle. When playing disc with multi-subtitle, press "SUBTITLE"  
key to switch among different displaying subtitles.  
Note: the function needs disc support.  
0-9: Number keys. When playing disc you can select track to play by number keys directly. In TV mode,  
you can select channels by number keys. e.g. To select the 8th track, press number key "0" and "8", then  
press "ENTER" key to confirm. To select track after 10th. e.g. The 18th track, press number key "1" and "8".  
then press "ENTER".  
Note: when playing VCD or SVCD, you can only select by number keys in PCB OFF mode.  
SETUP: System setup key. Enter system setup mode.  
SOURCE: To select source of input signal. Press "SOURCE" key, you can switch the mode among  
Tuner (TV Channel), F-COMP (front AV), R-Svideo (back S-video) and YCbCr (component video).  
DVD: In HDD or AUX in playback mode, press "DVD" button for 2 seconds to switch to DVD play mode.  
When playing DVD disc, press "DVD" back to DVD disc menu playback.  
When playing (S)VCD disc, press "DVD" button to turn on or off PBC function.  
Note: Definition of PBC: the signal recorded in VCD or (S)VCD disc that can control the playback.  
When playing the disc that contains PBC signal has the recorded information display on the TV screen  
as a menu, which makes it convenient to select disc content to play.  
In AUX operation mode, if it's showed "record to HDD" on TV screen, press "DVD" key to switch to  
"record to disc".  
DV/USB: When you connect DV or USB, press "DV/USB" to switch between DV and USB mode.  
HDD/DUB: In HDD or AUX in operation mode, press "HDD/DUB" key to switch to HDD menu playback.  
RETURN: When playing DVD disc, press "RETURN" key back to disc menu; In PBC ON mode,  
when play (S)VCD disc, press "RETURN" key back to PBC menu playback.  
ADD/CLEAR: Add or clear.  
EDIT: edit the recording content on the disc.  
TIMER: to enter timer-recording setup menu.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote  
STOP: when playing disc, press "STOP" key to stop playing; when recording program,  
press "STOP" key to stop recording.  
PAUSE: when playing disc, press "PAUSE" key to pause playing; when playing (S)VCD, DVD disc,  
press "PAUSE" key continuously to play the video pictures one by one; when recording, press "PAUSE"  
key to pause recording.  
PLAY: Play key.  
VOLUME-/+: adjust the volume.  
PREV/NEXT: If there are multi-titles or chapters in the DVD disc, you can choose the desired title  
or chapter by the button. Press "PREV" into previous chapter or title; press "NEXT" return to the  
next chapter or title.  
Note: Some discs do not support this operation.  
F.REV/F.FWD: YOU can choose fast speed of 2X, 4X, 16X, or 32X to play the disc content.  
1. When playing, press "F.REV, F.FWD" to adjust the speed.  
2. When fast playing, press "PLAY" to recover the normal playback.  
Note: Some discs do not support this operating.  
CHANNEL: to switch TV channels in TV playback mode.  
REPEAT:  
when playing DVD disc, you can switch the playback among chapter repeat, title repeat,  
disc repeat and normal playback by repeat key; when playing (S)VCD, CD disc, you can switch the  
playback among track repeat, disc repeat and normal playback by repeat key.  
REVERSE: To play backwards in slow motion. This function refers to (S)VCD, DVD disc only.  
SLOW/SORT: To play forwards in slow motion / sort. This function refers to SVCD, DVD disc only.  
A-B: segment repeat:  
When playing CD, VCD, SVCD, DVD discs, press this key to view random part of the disc repeatedly.  
When playing disc, press "A-B" once on the beginning point (point A) of the part that need to be repeated,  
point A is set. Press "A-B" again on the final point of the part. Then the part between Point A and B will play  
repeatedly. Press "A-B" key once move, current repeated part that has been set will resume normal play.  
FUNC: Function key: Press the key you can select desired operation mode through menu (as below)  
Functions  
DVD  
TV/Video  
Setup  
Timer Recording  
File Manager  
HDD  
GOTO: To search when playing disc, press "GOTO" key to select track or any time point to play.  
VIDEO: To switch Video output. In open mode, press "VIDEO" key to switch the Video output mode  
among YCbCr, YPbPr etc.  
ZOOM: To zoom out. When playing (S)VCD, DVD disc, press "ZOOM" key to zoom out the playing  
pictures by 1.5 times or 2 times.  
PIP: This key is to turn on/off PIP function. When playing DVD or video in HDD, PIP can display  
a window on the right upper corner of the TV screen, in which you can watch the TV program or input signal.  
Note: When playing MP4, MP3, VCD, CD, this function is unavailable.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Random  
When playing CD, (S)VCD, DVD, MP3 disc, press "DISPLAY" key twice until the TV screen display the menu  
of relative disc information, then move cursor to "MODE", press direction key "Right", move cursor to "Random"  
and press "ENTER" key to enter random mode.  
Programming playback  
When playing CD, (S)VCD, DVD, MP3 disc, press "DISPLAY" key twice until TV screen display the menu of  
relative disc information ,move "Mode", press direction key "Right", then move cursor to "Program"  
and press "ENTER" key to enter disc program mode TV screen will display as follows:  
Edit program Play List  
TRACK  
TRACK 01  
TRACK 02  
TRACK 03  
TRACK 04  
TRACK 05  
TRACK 06  
Program  
move cursor to the track need to program, press "ADD I CLEAR" key to pick up the track to program column  
and rearrange the orders of them. After programming the tracks, move cursor to the track in program column,  
and press "ENTER" key to enter programming playback.  
T-Shift  
The full name is Time Shift. This function has the AUX in signal recorded in the HDD so that you can  
control the playback speed by pressing keys like F.FWD / F.REW PAUSE etc. The recorded signal won't be  
saved after power off or stand-by.  
When T-Shift is ON, If set "Time buffer mode" in "Time Shift" item of the setup menu to "refresh", the  
previously recorded content will be cleared after the system changes. AUX in source (including switching  
TV channel); if you set that to "preserve" it will save the previously recorded content.  
When T-Shift is ON, each time when you press direction key "Left" , it will skip back to 10 seconds ago  
to play, each time when you press direction key "Right" , it will skip forward to 30 seconds later to play.  
When T-Shift is ON, press "T-Shift" to turn off the function and the system won't save the AUX in signals.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Basic Playback  
Play DVD Disc  
DVD  
1. Power on and put in disc.  
2. Start loading and playing the contents of disc automatically.  
3. When playing the disc, choose the desired title by direction key and press "ENTER" to play.  
4. When playing the disc, press "DVD" key back to disc title menu playback.  
5. Press "RETURN" key back to disc main menu playback.  
Play VCD, SVCD disc  
(S)VCD  
(Super) VCD should hold PBC (playback control) function, and have a playing menu to choose,  
PBC is defaulted on.  
1. Put in the disc.  
2. After loading the contents of disc, the PBC menu will show on the screen.  
3. Choose the content desired to play by number keys.  
4. Press "DVD" key to turn ON OFF PBC function.  
5. Press "RETURN" key back to PBC menu playback.  
What is PBC?  
There are controllable signals in VCD and SVCD. The disc holds PBC signal, would show its information  
on the TV screen as menu, which makes it easy to choose the contents.  
Play MP3 disc  
MP3  
MP3 (MPEG1 AUDIO LAYER-3) file is a kind of high compressed audio file. This technique can compress  
the data to 1/10 size. That is to say, compress 10 audio discs into one CD-ROM disc.  
1. Put in MP3 disc, the unit will read the data of the disc and show it on the screen.  
2. Choose the desired track by director or number key, press "ENTER" to confirm.  
How to program the playback?  
Choose the wanted tracks by director cursor and press "ADD/CLEAR" to take them into the playing list.  
After programming, press direction key "Right" to enter program playback list, then press direction key  
"Up/Down" to select desired track, press "ENTER" key to enter program playback.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Play CD disc  
CD  
1. Load the disc.  
2. The unit will recognise the disc type and automatically play disc information.  
Play Picture CD  
The unit can play Kodak Picture CD disc or JPEG file.  
(1) Load the Kodak picture CD, and it will play automatically.  
Press "STOP" key to enter picture browse playback.  
In normal picture playback, press direction key to rotate the picture, press "F.FWD" key, the picture will  
ZOOM by 12% 25% 50% 100% 200% 400% normal.  
In normal picture playback, press "ANGLE" key to change the circularly way in which the picture displays  
on the TV screen.  
(2) Load the JPEG file, the system will display file list of the disc on the TV screen after reading the disc type.  
Select the file you want to play by direction key "UP, DOWN".  
In normal picture playback, press direction key to rotate the picture, press "F.FWD" key, the picture will  
ZOOM by 12% 25% 50% 100% 200% 400% normal.  
In normal picture playback, press "ANGLE" key to change the display way in which the picture displays  
on the TV screen.  
Play DIVX disc  
DIVX/XVID: refer to the latest video compressed standard, which can recover a very low bit rate  
digital stream into high quality video, this kind of format can compress the information of a DVD disc into  
a normal CD disc, the supported MPEG4 subtitle is SRT (.srt) and SAMI (.smi).  
File Manager AUDIO 0:00:00/0:00:00  
How to make DIVX file?  
1. Computer equipment ( can surf on the internet,  
hold enough hard disc space, hold disc recorder.  
Operation system should be ... ...)  
2. Search for suitable DIVX file from the website,  
download and save it to the hard disc.  
3. Put in recordable disc after downloading record  
the download DIVX file into the disc.  
1
2
3
4
BAD  
BAD.SRT  
TURN  
TURN.SMI  
Load in DIVX disc, the unit would read the disc information and show it on the TV screen (refer to picture.),  
Choose the wanted tracks by the director key "Up/Down" or number key, press "ENTER" to play.  
When playing AV files, press "DISPLAY" key to display disc file list, move cursor to according subtitle files,  
press "ENTER" key to select the display subtitle.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Menu setup  
SETUP MENU-RECORDING  
-- Auto Chap Mark  
5min  
10min  
20min  
30min  
Off  
Auto Chapter Mark  
Record Duality  
When the option is set in "5" min", the unit will mark one  
chapter every 5 minutes automatically while recording  
when it set in "Off", the unit will not mark chapter while  
recording.  
HQ  
SP  
--Record Quality  
Mode:  
SP+  
LP  
Quality  
High Quality  
DVD Quality  
Common Quality  
Similar to DVD  
Better then VCR  
VCR Quality  
Mode Recording Time  
EP  
HQ  
SP  
SP+  
LP  
EP  
SLP  
1 hour  
2 hour  
2.5 hour  
3 hour  
4 hour  
6 hour  
SLP  
SCAN  
Confirm  
APS  
This operation will modify saved  
channels, continue?  
OK  
CANCEL  
-- Automatic Search  
Modify Channel Information  
EDIT  
Modify Channel  
Through Automatic Search, the unit can save the found  
channels in order.  
P001  
Program Number  
Name  
Standard  
PAL B/G  
PAL D/K  
In Automatic Search status, press "Cancel" to cancel  
the search, and the channels received before will be stored  
NOTE: Before Automatic Search, (please set "Country Setup",  
select local TV system first:) please first check if  
SECAM is available in the channels of your country or area.  
If it is available you can auto-scan directly. If not, please  
setup the TV audio system first  
PAL I  
SECAM L  
SECAM B/G  
SECAM D/K  
Channel  
Search Type  
Band  
Frequency  
Standard  
Cable  
C-05  
Channel  
Fine Tuning  
Del  
-- Modify Channel:  
1. Channel name:  
OK  
Move cursor to the channel, press "CHANNEL-/+" key to  
select the channel need to name. Then move cursor to  
"Channel name", press "ENTER" key to enter edit frame,  
and select desired letters or figures by direction key to  
compose the channel name.  
OK  
CANCEL  
SORT  
SORT  
Program Table  
P001 _________  
P002 _________  
... ...  
OK  
CANCEL  
2. TV  
TVs in different countries or areas are in different systems,  
please check the TV system in your country or area before  
set this option. When set in AUTO the unit will set the TV  
system on the basis of the system of TV channels or disc  
played (input source is TV tuner).  
P008 _________  
Timer Setting Menu  
OK  
Timer Recording  
Source Quality Date Start End Recor PDC  
3. Channel scan mode:  
Press ENTER to review a scheduled  
recording create a new one.  
Scan according to channel: Search for TV channels  
according to the TV channels table provided by TV station  
(Each TV channel has a serial number provided by TV  
station, e.g. C-036, which is sent out together with the TV  
signals.)  
Press Function for other options.  
Country Selection  
Australian  
China  
France  
Spain  
Scan according to frequency: search for TV channel  
according to it's exact frequency.  
--- ---  
4. Band:  
Select "Standard", if use wireless antenna to search for TV  
channels.  
Select "Wired cable", if use wired TV to search for TV  
channels.  
-- Channel list  
Move cursor to the channel need to be reordered, then press  
direction key "Right" to pick it out from the list, then move it to the  
position you want and press direction key "Left" to insert it there.  
At last, move the cursor to "Confirm" and press "ENTER".  
5. Fine Tuning  
This option can only be set while watching TV. When  
watching TV, enter into "Fine Tuning" page in TV Setup.  
Because there might be some inaccuracy of the antenna,  
you can set the best frequency in the option. Adjust the  
-- Country Setting:  
Refers to choosing national channel mode. Because different  
country use different channel mode, before searching,  
please fixed the channel mode to the related country.  
Note: country set will lead to abnormal sound or picture,  
and even failure in channel search.  
frequency through "  
6. Del  
",then select Confirm.  
delete the current TV channel.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP MENU - VIDEO  
TV Type:  
PAL  
TV Type  
TVs in different countries or areas are in different systems,  
please check the TV system in your country or area before  
set this option. When set in AUTO, the unit will set the TV  
system on the basis of the system of TV channels or disk  
played (input source is TV tuner).  
NTSC  
4:3 LB  
TV Display  
4:3 PS  
--TV Display  
16:9 WS  
4:3LB when the unit is connected to normal TV set, wide  
screen picture will display on the TV screen, but a part  
will be cut automatically.  
4:3PS when the unit is connected to normal TV set, while  
playing wide screen films, there will be a black area in top  
and bottom.  
Interlaced  
Video Output  
Progressive  
16:9WS choose this option when the unit is connected with  
a wide screen TV set.  
-- Video output format  
If you select progressive output the interlace video has no  
output (including CVBS, S-Video, YCbCr --- ---)  
If you select interlace output the progressive video has no  
output (including HDMI, VGA, YPbPr --- ---)  
In open mode, press "VIDEO" key to switch between  
progressive video and interlace video.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP MENU-AUDIO  
-- Downmix  
ON  
Downmix  
ON: when playing disks with 5.1 channels ,the left speaker  
will output sound of left channel, and partial sound of centre  
and surround channels; the right speaker will output sound  
of right channel and partial sound of centre and surround  
channels.  
OFF  
RAM  
SPDIF Output  
LPCM  
LPCM 48K  
LPCM Output  
LPCM 96K  
OFF: All 5.1 channels have audio output.  
-- SPDIF Output  
Full  
Dynamic Range  
3 / 4  
RAW: when the unit is connected with an amplifier  
by coaxial or optical, please enable this option. When  
playing disk that recorded in Dolby Digital, DTS or MPEG  
format, the unit will send out digital sound code through  
coaxial or optical output. The amplifier must hold Dolby  
Digital, DTS and MPEG decoder.  
PCM: when this option is enabled, the unit will decode  
sound code into PCM signal when playing disk in Dolby,  
DTS and MPEG format, and send out through coaxial or  
optical output.  
1 / 2  
1 / 4  
Off  
SPEAKER SETTING  
Centre  
OK  
Speaker Setup  
On  
Off  
On  
Off  
Rear  
On  
Off  
Subwoofer  
Centre Distance  
Off  
0.3m  
0.6m  
1m  
1.2m  
1.5m  
-- LPCM Output:  
48K: the sampling frequency of LPCM digital audio output  
is 48KHz.  
Rear Distance  
96K: the sampling frequency of LPCM digital audio output  
is 96KHz. The amplifier must support 96KHz decoding.  
Note: LPCM refers to digital audio format without  
compression (no loss).  
Off  
1m  
2m  
3m  
4m  
5m  
Test Tone  
OK  
OK  
Test Tone  
Test Control  
All Circle  
Now Testing Front-left Speaker  
-- Dynamic Range:  
Front Left  
Front Right  
It's used to adjust the dynamic range compression to increase  
the Volume of small detailed audio when you watch movie of  
large dynamic range with low volume and can't enjoy the small  
detailed audio. It helps you not to disturb the neighbour or  
decrease the audio quality.  
EXIT  
Centre  
Rear Left  
Rear Right  
Subwoofer  
Speaker setup  
Only when Downmix is "OFF", can you enter this setup.  
-- Front Speakers  
When speakers are set to "ON" . there's audio output from the terminal of the channel.  
When speakers are set to "OFF" , there's no audio output from the terminal of the channel.  
-- Centre Speakers  
When speakers are set to "ON" , there's audio output from the terminal of the channel.  
When speakers are set to "OFF" , there's no audio output from the terminal of the channel.  
-- Rear Speakers  
When speakers are set to "ON" , there's audio output from the terminal of the channel.  
When speakers are set to "OFF" , there's no audio output from the terminal of the channel.  
-- Subwoofer  
When set in "On" , there will be signal sent out to Subwoofer output.  
When set in "Off" , there will be no signal sent out to Subwoofer output.  
-- Centre distance:  
To delay the time of audio out from centre speaker.  
-- Rear distance:  
To delay the time of audio out from rear speakers.  
-- Channel distance:  
To select test audio signal of each channel output from unit.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP MENU-LANGUAGE  
-- System Language  
English (GB)  
Select the language you use to operate the unit.  
System Lang.  
-- Audio Language  
This option is available when the disk supports such audio,  
sounds and menu language.  
If the disk has no optional audio language, this option will not work.  
English  
Audio Lang.  
... ...  
-- Subtitle Language  
This option is available when the disk supports such  
subtitles, sounds and menu language.  
If the disk has no optional audio language, this option will not work.  
English  
Subtitle Lang.  
... ...  
-- Disc Menu Language  
This option is available when the disk supports such  
subtitles, sounds and menu language.  
If the disk has no optional audio language, this option will not work.  
English  
Disc Menu Lang.  
... ...  
SETUP MENU-DATE/TIME  
-- Set up-date-time:  
Manual: you can set the time and date as the exact time of  
your local place by hand;  
Auto: (The earth is divided into 24 time zone, each places  
may be in different time zone, and TV station obey the local  
time).  
Date-Time Setting  
Manual  
P001  
Program  
-- TV station:  
You can only enter it when date--time is set to auto, which  
means that time of the unit is according to time of the  
current watched TV station.  
Day (dd/mm/yyyy)  
06 01 2006  
-- Date  
You can change year, month and day in the option.  
-- Time  
Time (hh:mm)  
16:15  
You can change time in the option.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP MENU-PREFERENCE  
-- Parental Control  
When play disks with age control, you can decide the disks  
that can be played on the unit through age control.  
NO PARENTAL  
Parental Level  
1 G  
2
-- Change Password  
When entering the option, the TV screen will show as below:  
3 PG  
4 PG13  
5
Enter Password  
Enter password here  
6PG-R  
7 Nc17  
8 ADULT  
OK  
Cancel  
The default password is: 8806. Input the new password and  
press ENTER to confirm.  
Change Password  
Factory Defaults  
New Password  
OK  
Enter password here  
Input new password  
Input new again  
-- User Default:  
Reset to all the setup status.  
OK  
Cancel  
-- Screen saver  
Factory Defaults  
OK  
System will reset all setup items to  
the default values OK to confirm  
Cancel to exit  
After the unit remains in STOP or NO Disk status for a few  
minutes, the screen saver will show a floating picture to  
protect the TV kinescope if the screen saver is on.  
OK  
Cancel  
Screen saver  
ON  
OFF  
-- Component input  
YCbCr  
RGB  
Select YCbCr and there will be signal output in YUV terminal  
when Video format output is set to interval YUV. It's YCbCr  
output, when set to progressive YUV, It's YPbPr output select  
RGB when the Video format output is set to progressive,  
there will be video output to VGA terminal.  
SCART Output  
SETUP MENU-Time-Shift  
-- Time shift buffer mode:  
Refresh: means the recorded contents will be erased if you  
switch input source or TV channel after T-Shift function is ON.  
Preserve: means not to erase.  
Time shift buffer  
Hard disk info  
Refresh  
Preserve  
Notice!  
Show  
HDD Size:  
151504MB  
-- HDD information:  
Show relative information about HDD.  
Used space: 48736MB  
Remain space: 102768MB  
Title Number 14  
OK  
-- Space management:  
If you need to record more contents to HDD when it's full.  
Select Manual: system will indicate that HDD is full and can't  
record any more.  
Select Auto: system will delete the oldest title to record new  
contents automatically.  
Space Manage  
Automatically  
Manually  
Empty hard disk  
Confirm  
Go  
All video programs on the hard disk  
drive will be lost. Do you want to  
continue?  
OK  
Cancel  
-- Erase HDD:  
Erase HDD contents.  
Erase optical disc  
-- Erase disc:  
Erase disc can only be entered in AUX in operation mode,  
and it's only available to DVD+RW and DVD-RW disc.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Basic recording  
Preparing for recording  
This unit can record on DVD+R/RW, DVD-R/ RW discs. If you want re-record a disc, please select DVD+RW/DVD-RW.  
This disc type can be re-written for 1000 times.  
ATTENTION:  
-- The unit is not able to record on DVD-RAM, CD-R, or CD-RW discs.  
-- Video signal in PAL system and NTSC system can't be recorded on the same disc.  
-- Before recording, please check for the latent problem that might cause recording failure, such as scratch and spot.  
NOTE:  
-- For some DVD devices, the recorded DVD+R or DVD-R discs can only play after closing.  
-- When a disc contains too little information, some player might not be able to play it.  
Disc Resume Record:  
If the recording is halted by power cut, the unit can resume those information that has been recorded.  
1 .Turn on the unit.  
2. Read the disc.  
3. The screen will display the window of resume disc data.  
4. Press ENTER to start resuming disc.  
The unit can't record the video signal with copyright protection.  
General recording  
TV Tuner  
AV input on front  
1. Press " " to turn on the unit.  
2. Turn on the TV, select correct input source, then signal from the  
unit will display on the TV screen.  
S-video input on rear  
3. Press " ", place a recordable disc.  
4. Press " ", close the disc tray.  
YCbCr  
5. Press "SOURCE", to select recording sources are listed as below:  
6. If TV program is selected, press "+CHANNEL-" or number keys to select  
the program you need to record.  
DV input  
7. After selected recording source, press "RECORD" to start recording.  
8. To avoid recording advertisement or other useless content, you can press "  
after advertisement, press "RECORD" again to resume recording.  
9. Press " " to stop recording.  
" to pause recording;  
(NOTE: A few seconds is necessary to update the disc after stop)  
NOTE:  
When recording signal from DV. The buttons " ", "  
control the DV.  
", "  
" on remote can  
Play Recorded Program:  
Press " " to play recorded program.  
NOTICE: When recording source is set in DV, after stop recording, you must press "SOURCE" to  
switch to DVD playback mode to play the recorded program.  
Watch other TV program while recording:  
Press "AV/TV" on TV remote to switch the TV into TV mode.  
NOTE:  
-- If you do not want to watch TV while recording, you can turn off the TV. Please be careful that if you are  
using topbox, make sure it's in WORK status.  
-- After pressing "RECORD", recording will start in few seconds.  
-- During recording or record pause, you can not change recording quality.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDD playback  
Press "HDD/DUB" key after power on to enter  
HDD menu, move cursor to select desired title  
and press "ENTER" key to play.  
HDD  
No.  
Play  
CH  
Date  
Time Title  
A
Delete  
Split  
001 CH007 01/01/01 17:02 Title 1  
002  
003  
004  
005  
006  
007  
008  
Other playback function:  
Segment  
Rename  
Lock  
Press Add/Clear key to Select  
Program(s)  
After entering HDD menu, press direction  
"Right" and the system will show the function  
menu:  
Select "Play" and press "ENTER" key to  
play selected title;  
Press Dub key to copy selected  
Program(s) to DVD  
Protect  
Press Sort key to sort Program  
by name, date or time.  
Select "Delete" and press "ENTER" key to  
delete the selected title from HDD.  
Note: the title deleted from HDD can't be recovered.  
Select "Split" is to divide a title into 2 or even more  
For other options Press DVD, TV/VIDEO, USB, SETUP or TIMER  
keys.  
titles, operation as follows: move cursor to "Split", press "ENTER" key to enter title playback and wait until  
the time point that needs to divide, press "ENTER" key and wait for seconds the time point will be divided.  
Then the system will return to HDD menu, and you can find there's one more title that is divided out.  
Select "Segment" is to insert a chapter mark into selected title. When playing title that needs to be marked,  
each press of "ENTER" key will have one chapter segment inserted.  
Change index picture: each title have a picture displayed on the upper right of the HDD menu. Through this  
setup you can change the index picture, when the playing title goes to the picture that needs change,  
press "ENTER" key to make it.  
Rename: the system gives each title a title name, through this setup, user can change the name to a familiar  
one. Move cursor to "Rename", press "ENTER" key and rename menu composed of letters and figures etc will  
display on TV screen, move cursor to desired letter or figure by direction key, press "ENTER" to make it.  
Lock: is to lock selected title, means when you want to play the title, you have to input code, when you need  
other operation. e.g. delete divide etc.  
Note: super code: 8806.  
Protect: is to prevent the selected title from being deleted. Split or segment.  
How to copy the content of USB to the disc?  
When the unit is working, plug the USB flash or card-reader with memory card into the USB jack  
in the front panel.  
Press "DV/USB" key to switch the operation mode to USB playback mode.  
Press "EDIT" key, the system will indicate to enter USB to DVD back up mode.  
Move cursor to select the file that needs copy. Press "ADD/CLEAR" key and the system will send  
selected file to selected file list.  
After select the files, press "RECORD" key to start copy.  
Note: The disc used to copy must be blank recordable disc or recordable disc recorded with similar files.  
Recordable disc with different type of files can not used to copy.  
How to copy the content of HDD to disc?  
When the unit is working, load a blank recordable disc, press "HDD/DUB" key to enter HDD menu.  
Move direction key to select title that needs copy, press "ADD/CLEAR" key, and system will display the title,  
disc capacity it would take and how many titles you can select at the same time on the up side of HDD menu.  
After selection, press "HDD/DUB" key to start copy.  
During the process of copy, system enter AUX in playback mode.  
Note: If the disc contains files of other mode or type, it can not used to copy.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disc operating  
-- Rename disc:  
Play title  
Select "Rename disc" by direction key, press  
"ENTER" key to enter name disc menu. After  
input the new name, move cursor to "confirm",  
press "ENTER" key to complete renaming.  
--Erase disc:  
Through this function, you can erase all the  
contents on the disc. Select "erase disc" by  
direction key, press "ENTER" key to erase.  
-- Overwrite disc:  
When the unit reads and shows the disc menu  
of the disc with recorded contents, select  
"Overwrite disc", press "ENTER" to enter  
recording preparing mode, select the source to  
record from, press "RECORD" to record new contents.  
-- Lock disc:  
Rename disc  
Erase optical disc  
Erase optical disc  
PAL  
DVD  
EDIT  
Waring: This operation will  
erase all data in the disc. Are  
you sure you want to continue?  
YES  
NO  
Record a new title  
Overwrite disc  
Lock disc  
This function is to protect disc from being deleted its  
recorded contents by mistake. Select "Lock disc" by direction key, press "ENTER" key to lock.  
Note: when the recording hasn't finished, this function can also prevent from deleting the contents  
already recorded by mistake.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disc Editing  
-- Edit title:  
(1) Mark picture  
Play title  
Edit title  
Normally the first recorded picture is regarded as title picture,  
through this function you can make any picture in the title to be  
title picture. In disc playback mode, for the position of  
the picture that can be title picture, press "PAUSE" key, and  
press "EDIT" key to select "Mark picture", press "ENTER" key  
to confirm, and press "EDIT" key again to save the setup and  
return to disc menu playback.  
EDIT MODE  
Title  
01/01  
Chapter: 01/01  
PLAY  
A
B
C
Chapter marker  
Hide Chapter  
Inbox picture  
Split title  
Time: 0:15: 36  
(2) Split title  
Rename title  
Erase title  
Through this function, you can divide a title into several  
independent titles of different length. In disc menu playback,  
select title that needs split, press "ENTER" key to play at the  
point you want to divide, press "EDIT" key to select "Split title",  
and press "ENTER" key to confirm, press "EDIT" key again to save  
the setup and exit.  
Overwrite title  
Overwrite disc  
Append title  
(3) Chapter mark  
Through this function, you can divide a chapter into several  
ones or combine several chapters into one. A disc can contain  
maximum 124 chapters and maximum 99 titles. If the chapters  
exceed the limit, system will warn "too many chapters", and  
existing mark will be deleted before new mark added. In disc playback mode, at the point you want to divide press "EDIT"  
key to select "Chapter mark", press "ENTER" key to confirm select "insert chapter title", press "ENTER" key to confirm  
at last press "EDIT" key to save.  
Note: Those chapters will be saved on the disc in pending format, because recordable disc has no compatibility process  
mode (normal DVD player can't read it), however the self-defined chapter mark, during recording can play in normal DVD  
player after "close disc".  
(4) Hide chapter  
Through this function, when the recorded contents is playing, you can skip those that you don't want to watch  
(e.g. commercial advertisements).  
First, edit the contents you don't want to watch into an independent chapter by edit function, then when playing the  
chapters after edit, select the title that needs to be hidden, press "EDIT" key to select "hide chapter", press "ENTER" key  
to confirm, press "EDIT" again to exit from edit menu and renew disc contents. And when  
playing title contents, the chapter hidden won't play.  
-- Rename title:  
In the disc menu of disc with recorded contents, select desired title by direction key, then press "Rename title";  
press "ENTER" key to enter name title menu. After input the new name, move cursor to "confirm", press "ENTER" key  
to complete renaming.  
--Erase title:  
Through this function, you can delete title you don't need. In the disc menu of disc with recorded contents, select desired  
title by direction key; select "Erase title", press "ENTER" key to erase.  
-- Overwrite title  
Through this function, you can cover title you don't need and record new contents in it's original place. In the PBC menu  
of disc with recorded contents select desired title by direction key, then select "Overwrite", press "ENTER" key to enter  
recording preparing mode, select source to record from, select "RECORD" key to record new contents.  
-- Overwrite disc:  
When the unit reads and shows the disc menu of the disc with recorded contents, select "Overwrite disc", press "ENTER"  
to enter recording preparing mode, select the source to record from, press "RECORD" to record new contents.  
-- Add  
It can continue to record from the end of the last title, but not record another title. Select the last title, then press "ADD",  
press "ENTER" key to enter recording waiting mode; press "SOURCE", "Channel -/+"or number keys to select satisfactory  
input source press "ENTER" to record (until the disc is full or recording is stopped).  
Note: The beginning of added recording is the end of the last title.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup timing record  
Timer recording setup menu:  
Timer Recording Setup  
Through timer recording setup menu, you can record the contents  
you want in scheduled time. This function is usually used to record  
TV program, press "TIMER" key to enter timer recording setup menu.  
Note: system can set 8 timers at the same time. The scheduled time  
shall not exceed 1 month.  
Source  
Record To  
Quality  
Mode  
Date  
Front CVBS/Rear S-VIDEO/YUV --- ---  
HDD/DVD  
HQ/SP/SP+/LP/EP/SLP  
Once/Daily/Weekly/Mon~Fri/Mon~Sat/Weekend  
06/01/07  
17: 55: 45  
17: 56: 45  
Title 1  
Start  
End  
-- Recording source:  
Title  
Through this function, you can select desired input source of recording. VPS  
Note: If there's no signal output from the source at the scheduled time,  
the system won't record.  
OK  
Cancel  
-- Record to: choose to record the contents from input source to  
HDD or disc.  
Press SELECT to cancel the timer  
recording setting.  
-- Quality: select the quality of the recorded Video.  
-- Mode: select the repeat modes of recording.  
Once: record only once  
Every day: record in the scheduled time everyday automatically.  
Every week: record in the scheduled time every week automatically.  
Mon.-Fri.: record in the scheduled time from Monday to Friday automatically.  
Mon.-Sat.: record in the scheduled time from Monday to Saturday automatically.  
Weekend: record in the scheduled time on weekend automatically.  
-- Date:  
It's available when the recording mode is set to "Once" only.  
-- Begin:  
It's to set the beginning time of timer recording.  
--End:  
It's to set the end time of timer recording.  
Note: when setting more than one timers, the scheduled time shall not be overlapped.  
--Title:  
Display the title name of recorded items. Title name can be changed through this function.  
-- PDC:  
ON: Inserted advertisements won't be recorded.  
OFF: Inserted advertisements will be recorded.  
Note: This function is not supported if there's no PDC in the TV signal sent out by TV station.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
File editing  
Put in MP3, JPEG, Divx disc or plug USB  
with MP3, JPEG, Divx file, OSD will display  
a menu as follows:  
File Manager  
1 Don't go away  
2 Ameno  
AUDIO 00:00:00:-00:00:00  
A
Copy  
Delete  
Rename  
Move  
3 Goodbye Brother  
HDD  
DISC  
USB  
Create Dir  
Select all  
Unselect all  
Favorite  
Unfavorite  
Favorite list  
Move cursor to item need to play or edit,  
Press "ENTER" key to enter item menu list  
playback. Move cursor to desired file in the  
list and just press "ENTER" to play, if you  
want to edit the file, press direction key  
"RIGHT" to show the menu as the picture:  
Right Operation  
OK Play hilighted file  
Add Select/Unselect file  
COPY, to copy the file  
Move cursor to COPY and press "ENTER" key, OSD will show the menu:  
HDD  
DISC  
USB  
Select HDD to copy file to HDD;  
Select DISC to copy file to disc;  
Select USB to copy file to USB;  
After select the carrier, press direction "RIGHT" to show the instruction menu.  
TO COPY to start copying the file.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Additional information  
Usual Issues  
What is S-Video cable?  
S-Video is also called SVHS, which transfer luminance and colour signal. This tiny pocket DIN faucet is  
also called HOSIDEN faucet.  
What is composite video? (CVBS)  
The socket is usually called CINCH socket, which is used for transferring composite video signal (FBAS,  
CVBS). In this way, chromatism and luminance signal will be transferred together.  
Connecting to other VCR  
After recorded cassette video tape, no signal shows when playing in DVD recorder. Why?  
Check if cable is fastened securely.  
If the input video signal is very weak or do not match correlative standards, it will not be recognised by  
the recorder.  
Can PAL and NTSC signal be recorded on one DVD+R/+RW disk?  
NO. As DVD standard, the unit does not allow to record both PAL and NTSC signal on one disk.  
Disk Content Management  
Can new caption be added on DVD+R disk?  
Yes. If only the disk has not been closed, you can add new caption on it.  
Close Disk  
After closing disk, the recorded DVD+R disk can play on normal DVD player.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Should your DVD recorder develop a problem, please check below before  
requesting service:  
Symptom  
Check and Action  
Check if the power cord has been properly connected to the power outlet.  
Check if the main power has been switched on.  
No Power  
Does not play  
No disc, load a disc.  
Disc has been loaded upside down. Place the disc with the label side up.  
Disc's region code does not match to the player.  
Disc is not correct type for the player.  
Disc is damaged or dirty, clean the disc or try another disc.  
There may be moisture condensation inside the player. Remove the  
disc and leave the unit power on for one or two hours.  
No Picture  
Check if the TV set has power on, use TV remote to select A/V signal for  
DVD rather than broadcast.  
Check if the system connection is secure.  
Check if the connection cables are damaged.  
Clean the disc.  
The disc is dirty or damaged. Clean the disc or try another disc.  
Reset the colour system of the player or the TV set.  
Picture  
noise / distorted  
Try to direct the player to the TV set instead of via other components,  
such as a VCR.  
Select the screen format from the player's SYSTEM MENU,  
see "SYSTEM MENU" of this manual.  
Picture not full  
screen  
Select the screen format from DVD disc menu.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
DIVX, XVID, DVD, VCD, SVCD, CD, CD-MP3,  
DVD+RW, DVD+R, DVD-RW, DVD-R, CD-RW, CDR,  
KODAK PICTURE CD.  
Type of Disc Playback  
Type of disc recording  
Signal-noise ration  
DVD+RW, DVD+R, DVD-RW, DVD-R  
>90dB  
>80dB  
>80dB  
<-65dB  
Dynamic Range (1kHz)  
Crosstalk (1kHz)  
Distortion/noise (1kHz)  
RF TV out x 1,  
HDMI x 1  
Output Terminals  
VGA x 1,  
S-video x 1,  
Component Video (YCbCr & YPbPr) x 1,  
Composite video & audio x1,  
5.1 channel output x 1,  
Digital Audio Coaxial output x 1,  
Digital Audio Optical output x1  
Antenna in x 1,  
S-video x 1,  
Front Composite video & audio x 1,  
Rear Composite video & audio x1,  
DV input i-Link (IEE1394)  
USB input i-Link  
Input Terminals  
Power input  
AC 100-240V 50/60Hz  
Body size: W430 x D327 x H48 mm  
Net weight: 4.5Kg  
Dimension  
(Main unit only)  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PALSONIC CORPORATION PTY LTD  
1 JOYNTON AVENUE  
WATERLOO NSW 2017 AUSTRALIA  
TEL: (02) 9313 7111  
FAX: (02) 9313 7555  
PALSONIC CUSTOMER SERVICE  
TELEPHONE  
AUSTRALIA: 1300 657 888  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Clothes Dryer T 8012 C User Manual
Murphy Portable Generator MGC447 User Manual
Napco Security Technologies Door GEM DXRP3 User Manual
NEC Car Video System LCD73VXM User Manual
NEC Computer Monitor LA 1422JMW User Manual
NEC Home Theater System NP60J User Manual
Nextar Digital Photo Frame N7 204 User Manual
Nextar GPS Receiver SNAP3 User Manual
Oakley Watch 04 00774 User Manual
Onkyo Speaker HT R508 User Manual