Packard Bell
Grafite & Carbon
Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
About this Guide
This guide contains systematic disassembly instructions for the Packard Bell Grafite & Carbon. The
instructions are illustrated where necessary with images of the part that is being disassembled.
Packard Bell B.V. reserves the right to make changes to the Grafite & Carbon without notice.
For More Information
For more information about the Packard Bell Grafite & Carbon, visit Packard Bell‘s support web site
documentation and detailed specifications.
Technician Notes
Only technicians authorized by Packard Bell B.V. should attempt to repair this device. Because of the
complexity of the individual boards and subassemblies, no one should attempt to make repairs at the
component level or to make modifications to any printed wiring board. Improper repairs can create a
safety hazard. Any indication of component replacement or printed wiring board modifications may
void any warranty or exchange allowances.
Disassembly
When disassembling the device, follow these general rules:
„
„
„
„
Turn OFF the power using the power button and disconnect the AC adapter.
Do not disassemble the device into parts that are smaller than those specified here.
Label all removed connectors; note where the connector goes and in what position.
Use something to hold the small screws (trays, jars, or cups). Label each cup with the
disassembly step number. This can reduce questions about where each screw came from
during re-assembly.
Reassembly
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws
are returned to their proper positions. Check that no tools or any loose parts have been left inside the
device. Check that everything is properly installed and tightened.
„
„
The LED cable goes on the outside of the hard disk drive casing, not underneath the drive!
The spacer clips are fitted so that they touch the top cover when the device is on. They
have been designed to reduce vibrations during operation.
Required Tools
All disassembly procedures can be performed using the following tools:
„
Small Phillips screwdriver.
Packard Bell Grafite & Carbon Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Front Cover
Perform the following steps to remove the front cover:
1. Make sure the power is off.
2. Turn the device upside down.
Note: Use an anti-static mat or something soft like a piece of cloth underneath the device to prevent damage to the
exterior of the casing.
3. Insert a flat-blade screwdriver in the 2 orifices to release the front cover and slide the cover
up and out of the compartment.
Fig. 1 Removing the front cover.
Top Cover
the following steps:
1. Turn the device over so the top is facing up.
Packard Bell Grafite & Carbon Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4
2. Slide the top cover to the front of the device and remove the cover.
Fig. 2 Removing the top cover.
Hard Disk Drive
1. Remove the 4 screws (2 on either long side) securing the hard disk drive in the device.
Note: One of the screws on each side of the hard disk drive holds a spacer clip.
Fig. 3 Removing the hard disk drive screws.
Note: In Fig. 3 only 2 screws are visible; the other 2 screws are located on the other side of the hard disk drive.
Packard Bell Grafite & Carbon Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2. Slide the hard disk drive towards the front to disconnect it from the I/O board.
Fig. 4 Removing the hard disk drive.
I/O Board
then perform the following steps:
1. Remove the 2 screws securing the I/O board.
Fig. 5 Removing the I/O board.
3. Carefully take out the I/O board from the device.
Packard Bell Grafite & Carbon Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Notice
The information in this guide is subject to change without notice.
This guide contains information protected by copyright. No part of this guide may be photocopied or
reproduced in any form or by any means without prior written consent from Packard Bell B.V.
PACKARD BELL B.V. SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR
OMISSIONS CONTAINEDHEREIN; NORFOR INCIDENTAL ORCONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
Copyright © 2009 Packard Bell B.V. All rights reserved.
Packard Bell is a registered trademark of Packard Bell B.V.
The names of actual companies and products mentioned herein may be trademarks and/or
registered trademarks of their respective owners.
Grafite & Carbon Disassembly Manual
Authors: Dean Egberts & Juan M. Calviño
First Edition: February 2009
Version: 1.0
Part Number: CS036A00
Packard Bell B.V.
Packard Bell Grafite & Carbon Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
|