Oricom Clock WNS1 User Manual

Oricom WNS1  
Jumbo Display  
Alarm Clock and Shaker  
User Guide  
Keep this user guide for future reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION OF CONTROLS  
PM  
AL  
1
2
3
1 – PM LED indicator  
2 – Alarm LED indicator  
3 – Strobe light and snooze button  
9
8
1
2
7
3
6
4
5
1 – Alarm mode switch  
2 – Alarm and ring volume  
3 – Set alarm  
6 – Alarm off  
7 – Alarm tone  
8 – Alarm + ring / Off / Ring function switch  
9 – Shaker Lo / Hi switch  
4 – Set clock  
5 – Set hours & minutes  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INITIAL SETUP  
PACK CONTENTS  
Unpack the unit and check to be sure you have all the items below.  
·
1 Jumbo display /alarm clock (WNS1)  
·
·
·
·
·
1 modular line Cord  
1 Double adaptor plug  
1 Shaker  
1 Warranty Card  
This User guide  
Battery Door  
4
1
AC Adaptor  
Double Adaptor  
Phone Wall  
socket  
3
Shaker  
Dimmer switch  
2
INITIAL SET UP  
-
Connect one end of the phone line cord to the back of the unit (1) and the other end to the  
double adaptor plug.  
- Plug the double adaptor into the telephone wall socket.  
- Connect the AC adaptor to the socket (4) on the back of the unit.  
-
-
Plug the AC adaptor to the power socket on the wall.  
Plug in the shaker to the back of the unit.  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ALARM AND CLOCK FUNCTION  
SETTING THE TIME (  
)
-
-
-
-
Press and hold  
(set clock) button.  
Press H (hour) and M (minute) until correct hour and minutes appear on the display.  
Release (set clock) button.  
For p.m. hours, the p.m. indicator will appear on the display near the inscription PM.  
SETTING THE ALARM TIME (  
)
-
-
-
-
Press and hold  
(set alarm) button.  
Press H (hour) or M (minute) until correct hour and minutes appear on the display.  
Release  
Press  
(set alarm) button.  
H and M to reset the alarm clock to 12.  
SETTING THE ALARM MODE  
Put the function switch on A+T position. Choose which alarm mode you wish to be awakened to by  
moving the alarm mode switch to one of the following selections:  
V
:
only shaker activated  
V+S :  
F+V :  
both sound and shaker alarm activated  
both strobe light and shaker alarm activated  
When the alarm is set to one of the alarm modes, the alarm indicator will appear on the display near  
the inscription AL.  
The table below shows how the alarm modes indicate an incoming call from the alarm clock.  
ALARM MODE  
SOUND  
ACTION  
Buzzer  
ALARM CLOCK  
Continuous  
INCOMING CALL  
With pauses  
SHAKER  
STROBE LIGHT  
Vibrates  
Flashes  
Continuous  
Continuous  
With pauses  
With pauses  
SNOOZE BUTTON  
/ STROBE LIGHT  
When the alarm sounds, you can use the  
snooze button to temporarily turn off the alarm. The  
alarm will come on again after 9 minutes. This sequence can be carried out for up to 2 hours after  
which the alarm mode will be automatically switched off.  
SWITCHING THE ALARM OFF  
Press the alarm off button (OFF), the alarm will them operate at the same time the next day. The  
alarm if not switched off will continue to sound for up to 2 hours and then be automatically switched  
off.  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RINGER ON/OFF SWITCH (A+T / OFF / T)  
-
-
-
A+T (alarm + telephone): for the alarm and telephone ring position.  
OFF: alarm and ring off.  
T (telephone): for the telephone ring position.  
HOW TO USE WITH YOUR TELEPHONE  
-
-
-
Ensure that your telephone is connected to the WNS1 as shown in the installation section.  
Select the ringer On/Off switch on the A+T or T position for the ring.  
Choose which of the alarm modes you wish to alert you of your incoming telephone calls (see  
page 5: V, V+S, S+F or F+V)  
-
When the alarm mode selected indicates there is an incoming telephone call, lift the telephone  
handset and answer the call. When you have finished the call replace the handset and the  
alarm will be ready to indicate the next call.  
DIMMER SWITCH (  
)
Adjust the brightness of the display by moving the  
control at the rear of your WNS1.  
VOLUME CONTROL  
Use this to set the volume of the ringer and the alarm sound.  
TONE  
This allows you to select the tone of the alarm sound that is best for you.  
SHAKER SWITCH (  
- / + )  
Sets the motion of the shaker to Lo (-) or Hi (+)  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE & WARRANTY  
CLEANING  
The surface of the case can be cleaned with a dry, soft, lint-free cloth. Never use cleaning agents,  
particularly aggressive solvents. Apart from occasional cleaning of the case, no other care is  
necessary. The rubber feet on the base are not resistant to all cleaning agents. The rubber feet do  
not normally leave any marks on the surface. However, on account of the multitude of varnishes and  
surface finishes used, surface marks caused by the feet of the unit cannot be ruled out.  
This product is covered by a 12 month warranty against defective workmanship or parts. The warranty  
does not extend to damage caused by misuse, negligence, water ingress, excessive voltage,  
telephone line faults or lightning. This guarantee in no way affects your statutory rights. Full details of  
the warranty are contained in the enclosed warranty card.  
WARRANTY  
If you feel this product is not working correctly please consult the user guide and ensure that you are  
using the product in accordance with the instructions. Remove all extra telephone equipment and  
connect only this telephone directly to the telephone socket.  
If the fault is still present, connect another telephone (if available) to the telephone socket. The  
results will show you whether the fault lies with this unit or with the telephone line.  
If the product is working correctly the fault is on the telephone line. Please contact your network  
operator for assistance.  
To order replacement batteries and in case of any technical issues you may have with this  
product please consult our website for further information or send us an email for a prompt  
response to your enquiry.  
In the unlikely event of a fault developing, please contact us for assistance. If the product is then  
found to be faulty you will be asked to return it directly to us with a copy of the purchase receipt.  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
South Windsor, NSW 2756  
Customer support  
Fax: (02) 4574 8898  
Ph: 1300 889 785  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Milwaukee Saw 6177 59 User Manual
NETGEAR Network Card XWNB5201 User Manual
Network Technologies Computer Monitor CM DT17 User Manual
Nikon Camera Lens 30 110MMWHT User Manual
Nikon Film Camera 140ED User Manual
Olympus Camera Lens 261012 User Manual
Omega Engineering Thermometer CL521 User Manual
Onkyo DVD Player DV S555 User Manual
Pacific Digital Stereo Receiver AVR 635 User Manual
Panasonic Video Gaming Accessories CZ RD516C User Manual