Onkyo Stereo System TX DS595 User Manual

Contents

Before using

Inportant Safeguards........................................ 2

Precautions....................................................... 3

Features ............................................................ 4

Supplied accessories ........................................ 4

Before using this unit ...................................... 5

AV Receiver

Facilities and connections

TX-DS595

Front panel facilities ........................................ 6

Remote controller ............................................ 8

Connections ................................................... 10

Connecting speakers ...................................... 14

Connecting the power.................................... 16

Connecting antennas...................................... 17

Instruction Manual

Setup and operation

Speaker setup ................................................. 19

Listening to Radio Broadcasts....................... 21

Listening to RDS broadcasts

(European models only) .......................................... 23

Enjoying music or videos with TX-DS595 ... 25

Using listening mode ..................................... 28

Input Setup..................................................... 29

Preference ...................................................... 32

Recording....................................................... 33

Remote controller

Thank you for purchasing the Onkyo AV Receiver.

Please read this manual thoroughly before making

connections and plugging in the unit. Following the

instructions in this manual will enable you to obtain

optimum performance and listening enjoyment from

your new AV Receiver. Please retain this manual for

future reference.

Using remote controller ................................. 34

Learning a pre-programming code ................ 38

Operating your programmed

remote controller ...................................... 40

Programming the commands of remote controllers

for other devices into the remote controller ..... 42

Using a Macro function ................................. 45

Appendix

Specifications ................................................ 49

Troubleshooting guide ................................... 50

Download from Www.Somanuals.com. All Manuals Search And Download.

21. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to the

appliance, ask the service technician to perform safety checks to

determine that the appliance is in proper operation condition.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL

ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

23. Wall or Ceiling Mounting – The appliance should be mounted

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other appli-

ances (including amplifiers) that produce heat.

ELECTRIC

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

NEC – NATIONAL ELECTRICAL CODE

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

Precautions

1. Warranty Claim

For U.S. models

You can find the serial number on the rear panel of this unit. In case

of warranty claim, please report this number.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s at-

tention to Section 820-40 of the NEC which provides guidelines for

proper grounding and, in particular, specifies that the cable ground

shall be connected to the grounding system of the building, as close

to the point of cable entry as practical.

2. Recording Copyright

Recording of copyrighted material for other than personal use is

illegal without permission of the copyright holder.

3. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power

does not come on, contact your Onkyo authorized service station.

FCC Information for User

CAUTION:

4. Care

The user changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

From time to time you should wipe the front and rear panels and the

cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a

weak solution of mild detergent and water, wring it out dry, and

wipe off the dirt. Following this, dry immediately with a clean

cloth. Do not use rough material, thinners, alcohol or other chemi-

cal solvents or cloths since these could damage the finish or remove

the panel lettering.

NOTE:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

5. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the area

where this unit will be used meets the required voltage (e.g., AC

230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

• Reorient or relocate the receiving antenna.

Worldwide models are equipped with a voltage selector to conform

to local power supplies. Be sure to set this switch to match the volt-

age of the power supply in your area before plugging in the unit.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

For British models

Replacement and mounting of an AC plug on the power supply cord

of this unit should be performed only by qualified service personnel.

For Canadian models

NOTE:

IMPORTANT

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CA-

NADIAN ICES-003.

The wires in the mains lead are coloured in accordance with the

following code:

Blue : Neutral

Brown : Live

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the termi-

nals in your plug, proceed as follows:

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modele pour les Canadien

The wire which is coloured blue must be connected to the terminal

which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the termi-

nal which is marked with the letter L or coloured red.

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CON-

FORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

IMPORTANT

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA

PRISE ET POUSSER JUSQU’AU FOND.

A 5 ampere fuse is fitted in this plug. Should the fuse need to be

replaced, please ensure that the replacement fuse has a rating of 5

amperes and that it is approved by ASTA or BSI to BS1362. Check

for the ASTA mark or the BSI mark on the body of the fuse.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE

SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND DIS-

POSED OF SAFELY. THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMPERE SOCKET.

If in any doubt, consult a qualified electrician.

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

I 75 Watts minimum of continuous RMS power to each

of the five channels into 8 Ω from 20 Hz to 20 kHz

with no more than 0.08% THD (USA models, FTC

rating)

I Non-Scaling Configuration

I Cinema Re-EQ^TM

I Late night mode (high, low, off)

I 5.1-Channel input

I 110 Watts minimum of continuous RMS power to

each of the five channels into 6 Ω at 1 kHz (European

models, DIN)

I 4 Assignable digital inputs (2 coaxial, 2 optical)

I Smart Scan Navigator with LEDs

I 40 FM/AM random presets

I IntelliVolume

I 140 Watts minimum to each of the five channels into

6 Ω at 1kHz (Asian models, EIAJ)

I Wide Range Amplifier Technology (WRAT)

I Extended Frequency Response (10 Hz to 100 kHz)

I Optimum Gain Volume Circuitry

I Powerful programmed/learning remote with macros

and mode-key LEDs

I Dolby^®* Digital, DTS^®, Dolby Pro Logic II decoding

I A-Form Listening Mode Memory

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby

•

Re-Equalization and the “Re-EQ” logo are trademarks of Lucasfilm Ltd.

Manufactured under license of Lucasfilm Ltd.

Manufactured under license from Digital Theater Systems, Inc. US Pat.

No.5,451,942 and other worldwide patents issues and pending. “DTS”

and “DTS Digital Surround” are trademarks of Digital Theater Systems,

Supplied accessories

Check that the following accessories are supplied with the TX-DS595.

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

INDUSTRIESTRASSE 20

82110 GERMERING,

GERMANY

AM loop antenna × 1

FM indoor antenna × 1

(connector will vary depending

on model specifications)

declare in own responsibility, that the ONKYO product described

in this instruction manual is in compliance with the corresponding

technical standards such as EN60065, EN55013, EN55020 and

EN61000-3-2, -3-3 (or EN60555-2, -3)

GERMERING, GERMANY

A.HORIUCHI

75/300 Ω antenna adapter × 1

(For all models other than USA,

ONKYO EUROPE ELECTRONICS GmbH

Remote controller × 1

Batteries (AA, R6 or UM-3) × 2 Canadian and European models)

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using this unit

Setting the Voltage selector

(Worldwide models only)

Using the remote controller

Point the remote controller toward the remote control sensor. The

STANDBY indicator lights up when the unit receives a signal from

the remote controller.

Worldwide models are equipped with a voltage selector to conform

with local power supplies. Be sure to set this switch to match the

voltage of the power supply in your area before plugging in the unit.

Determine the proper voltage for your area: 220-230 V or 120 V.

If the preset voltage is not correct for your area, insert a screwdriver

into the groove in the switch. Slide the switch all the way to the upper

(120 V) or to the lower (220-230 V), whichever is appropriate.

Remote control sensor

TX-DS595

STANDBY indicator

FRONT

CENTER

SPEAKER

SURROUND

SPEAKERS

ANTENNA

SPEAKERS

AC OUTLETS

SWITCHED

TOTAL 100W MAX.

MONITOR

OUT

DVD

VIDEO

OUT

VIDEO

REMOTE

CONTROL

VIDEO

FRONT

SPEAKERS

PHONO CD

TAPE

OUT

AV RECEIVER

MODEL NO. TX-DS595

CAUTION

120V

SEE INSTRUCTION MANUAL

FOR CORRECT SETTING.

FRONT

SURR

CENTER

OPTICAL

COAXIAL

VOLTAGE

SELECTOR

30˚

220-230V

GND

OHMS

MIN.

SPEAKER

OHMS

MIN.

/SPEAKER

30˚

SUB

SET BEFORE POWER ON

IMPEDANCE SELECTOR

SUBWOOFER

PRE OUT

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

Approx. 5 meters

(16 feet)

120V

VOLTAGE

SELECTOR

220-230V

-4

Notes:

• Place the unit away from strong light such as direct sunlight or

inverted fluorescent light which can prevent proper operation of

the remote controller.

Installing the remote controller batteries

1. Remove the battery compartment cover by pressing

and sliding the cover.

• Using another remote controller of the same type in the same

room or using the unit near equipment which uses infrared rays

may cause operational interference.

2. Insert two AA (R6 or UM-3) batteries into the battery

compartment. Carefully follow the polarity diagram

(positive (+) and negative (–) symbols) inside the

battery compartment.

• Do not put objects on the remote controller. Its buttons may be

pressed by mistake and drain the batteries.

• Make sure the audio rack doors do not have colored glass.

Placing the unit behind such doors may prevent proper remote

controller operation.

3. After batteries are installed and seated correctly,

replace the compartment cover.

• If there is any obstacle between the remote controller and the

remote control sensor, the remote controller will not operate.

Notes:

• Do not mix new batteries with old batteries or different kinds of

batteries.

• To avoid corrosion, remove the batteries if the remote controller

is not to be used for a long time.

• Remove dead batteries immediately to avoid damage from

corrosion. If the remote controller does not operate smoothly,

replace both the batteries at the same time.

• The life of the batteries supplied is about six months but this will

vary depending on usage.

Download from Www.Somanuals.com. All Manuals Search And Download.

Front panel facilities

Here is an explanation of the controls and displays on the front panel of the TX-DS595.

Front panel

1 2 3

See illustration below

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

STANDBY

POWER

RETURN

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

AV RECEIVER TX DS595

0 A

D E F

SETUP

DSP/MODE ADJ

For all models other

than European model

RETURN

PUSH TO ENTER

DISPLAY

DIMMER

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

G I

H J

Front panel display

Listening mode or digital input

format indicators

Speakers A/B indicators

Tuning indicators

SPEAKERS

SLEEP

MPEG

DTS

DSP

FM MUTE

MEMORY

RDS

STEREO

DIRECT

TUNED

FM STEREO

PCM DIGITAL

Sleep indicator

Multi function display

Download from Www.Somanuals.com. All Manuals Search And Download.

Front panel facilities

For operational instructions, see page indicated in brackets [ ].

SMART SCAN NAVIGATOR jog dial and indicators

[19, 20, 22, 24-27, 30-32]

POWER switch [16]

Used to make settings in the setup display, change listening mode

settings, and more.

Turns on and off the main power supply for the TX-DS595.

SETUP button [19, 20, 30-32]

STANDBY indicator [16]

Press to enter and exit the setup mode.

Lights when the TX-DS595 is in the standby state and flashes when

a signal is received from the remote controller.

RETURN button [19, 20, 30-32]

STANDBY/ON button [16]

Press to move up one level in the setup mode.

Press to turn on the TX-DS595 when in the standby state. Press again

to return the TX-DS595 to the standby state.

DISPLAY button [26]

The DISPLAY button is used to display information about the

current input source signal. Each time you press the display button,

the screen changes to show you different information concerning the

input signal.

SPEAKERS A/B buttons [25, 26]

Press these buttons to turn on and off speakers systems A and B.

CH LEVEL button [27]

RT/PTY/TP (European models only) button [24]

Press to select the channel whose level is to be adjusted.

This button is only available on European models. Use this button to

help tune into the Radio Data System (RDS) for FM broadcasting.

RDS was developed within the European Broadcasting Union

(EBU) and is available in most European countries. Each time the

button is pressed, the display changes from RT (radio text) to PTY

(program type) to TP (traffic program) and then back to RT again.

MASTER VOLUME dial [25]

The MASTER VOLUME dial is used to control the volume.

PHONES jack

To listen with headphones, plug a pair headphones with a standard

stereo plug into the PHONES jack on the TX-DS595 front panel.

When you connect headphones, the unit will enter STEREO mode

automatically and no sound will be heard from the speakers. If you

have selected MULTI CH INPUT, you will hear sound only from the

FRONT L and R channels. Note that the volume level for the

headphones is adjustable.

DIMMER (other than European models) button

Press to set the brightness of the front display. There are 3 settings

available: normal, dark, and very dark.

FM MODE button [21]

When there is too much noise in the stereo reception of an FM

broadcast, press to turn off the FM MUTE function.

PHONES

PRESET MEMORY button [22]

This button is used to assign the radio station that is currently tuned

in to a preset channel or delete a previously preset station.

TUNING

buttons [21]

AUDIO SELECTOR button [27]

Use these buttons to change the tuner frequency. The tuner

frequency is displayed in the front display and it can be changed in

50 kHz increments for FM and 10 kHz (or 9 kHz) increments for

AM.

This button is used to select the type of audio input signal. Each time

pressed, the setting cycles from “AUTO” → “MULTICH” →

“ANALOG” and back.

When FM is selected, you can hold down one of the tuning buttons

and then release it to activate the auto-search feature. It will search

for a station in the direction of the button you pressed and stop

when it tunes into one.

Input source buttons (DVD, VIDEO 1–3, TAPE, FM,

AM, PHONO, and CD) [25]

These buttons are used to select the input source.

PRESET

buttons [22]

BASS dial [26]

When AM or FM is selected as the input source, press one of these

buttons to jump to a radio station that you preset using the PRESET

MEMORY button. Pressing the right button moves from the most

recently preset station to older ones, and pressing the left button

moves in the reverse order.

Boosts or cuts the bass response. Bass adjustment is effective only

for the front speakers and headphones.

TREBLE dial [26]

Boosts or cuts the treble response. Treble adjustment is effective

only for the front speakers and headphones.

Front display

Remote control sensor [5]

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote controller

SEND/LEARN indicator

This indicator acts as a guide when commands are programmed into

or sent by the remote controller. It also warns the user when an error

is made or battery power is low.

ON/STDBY button [16]

ON: Turns on the TX-DS595.

STDBY: Places the TX-DS595 in the standby state.

Be aware that pressing the STDBY button only places the TX-

DS595 in standby and does not turn the power completely off.

SLEEP button [26]

Sets the sleep function.

The SLEEP button enables you to set the TX-DS595 to turn off

automatically after a specified time period.

DIRECT MACRO button [46]

DISC

VOL

For executing and programming the Direct Macro function.

MODE buttons and indicators [40-47]

AUDIO

MUTING

For selecting the component to be operated by the remote controller.

When a MODE button is pressed, it will light green for 8 seconds.

The selected MODE button will also light whenever any other

operation button is pressed to tell you which mode the remote

controller is in.

ANGLE

SUBTITLE

TV/VCR

LEVEL

RANDOM

REC

OPEN/CLOSE

RETURN button [19, 20, 30-32]

Press to move up one level in the setup mode.

DVD

CH/DISC

button [35, 36]

T 1

When in the RCVR mode, for selecting a tuner preset channel.

For selecting the disc to be played back for components with disc

changers when in the DVD or CD modes.

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

CH SEL/TOP MENU button [36]

SPA

SP B

Re-EQ

CH SEL: For selecting the speaker for level adjustment when in the

RCVR mode. Used together with the LEVEL

buttons.

DISPLAY

DIMMER

ZONE 2

ENTER

TOP MENU: When in the DVD mode, for displaying the menu

screen(s) recorded on DVD media.

-- ---

HOME THEATER CONTROLLER

RC 447M

AUDIO/TV/VCR button [27, 41]

AUDIO: For selecting the audio input signal. The setting changes

from “AUTO” to “MULTICH” to “ANALOG” and back each time

this button is pressed.

TV/VCR: Must be preprogrammed for use in the TV and VCR

modes.

LEVEL /ANGLE and LEVEL /SUBTITLE buttons

LEVEL

: Select the speaker whose volume is to be adjusted

using the CH SEL button and adjust the volume using the LEVEL

buttons in the RCVR mode. [9, 27]

ANGLE: When in the DVD mode, for selecting a camera angle

when a DVD-Video is recorded with multiple angle playback. [36]

SUBTITLE: When in the DVD mode, for selecting one of the

subtitle languages recorded on a DVD-Video. [36]

CD/TAPE/DVD/MD operation buttons [34-37]

For operating Onkyo components connected to the TX-DS595.

INPUT SELECTOR buttons [25]

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote controller

Selects an input source.

TEST/MENU button

Same as the input selector buttons on front panel of the TX-DS595.

The input source for each buttons is given here. DVD:DVD, CD:CD,

V1:VIDEO1, V2:VIDEO2, V3:VIDEO3, V4:Not used with the TX-

DS595, T1:TAPE, T2:Not used with the TX-DS595, TUN:FM/AM,

PH:PHONO.

TEST: Outputs a test tone for setting speaker levels.

Use this button in conjunction with the LEVEL

buttons to calibrate the speakers levels.

and CH SEL

1. Press the TEST button.

A test sound (pink noise) will be heard from the left front

speaker. At this point, it is not necessary to adjust the volume of

the test sound.

Numeric key/Listening mode selector/SP A, B/

Re-EQ/DISPLAY/DIMMER buttons

2. Press the CH SEL button.

The test sound will now be heard from a different speaker.

1 to 9, +10, --/---, 0: For entering the number of a track.

STEREO, DIRECT, DSP

, SURR, A.ST: You can select a

3. Use the LEVEL

buttons to adjust the volume of the test

listening mode. [25, 28]

sound from this speaker to the same level that you heard

from the previous speaker.

STEREO: Changes the listening mode directly to the Stereo

listening mode. If pressed, the listening mode for the selected

input source set in the Listening Mode Preset is also changed to

the Stereo listening mode.

SURR (Surround): Changes the listening mode to the surround

mode for the current input signal (e.g., Dolby Pro Logic II,

Dolby Digital, or DTS). If pressed, the listening mode for the

selected input source set in the Listening Mode Preset is also

changed to the Surround listening mode.

4. Repeat the procedure in step 2 and 3 until the volume of the

test sound from all speakers is the same level.

Each time you press the CH SEL button, the test sound will be

heard from a different speaker. The speaker order for calibration

is front left → center → front right → surround right → surround

left → subwoofer.

5. Press the TEST button to exit the setting.

For Dolby Pro Logic II, this button also changes the mode

between Dolby Pro Logic II Movie and Dolby Pro Logic II

Music.

DIRECT: Changes the listening mode directly to the Direct

listening mode. If pressed, the listening mode for the selected

input source set in the Listening Mode Preset is also changed to

the Direct listening mode.

For a more detailed explanation of how to calibrate the speaker

levels, see page 20.

MENU: When in the DVD mode, this button displays the DVD

menu.

MUTING button [26]

A.ST (All Channel Stereo): Changes the listening mode

directly to the Stereo listening mode. If pressed, the listening

mode for the selected input source set in the Listening Mode

Preset is also changed to the All Channel Stereo listening mode.

DSP / : Changes the listening mode as shown below.

Direct ↔ Stereo ↔ Surround ↔ Orchestra ↔ Unplugged ↔

Studio-Mix ↔ TV Logic ↔ All Ch Stereo ↔ Direct.

If pressed, the listening mode for the selected input source set in

the Listening Mode Preset is also changed.

Activates the mute function.

ZONE 2/SEARCH/ENTER button

ZONE 2: Not used with the TX-DS595.

SEARCH: When in the DVD mode, for finding the specific section

on a disc where you want to start playback.

ENTER: When in the MD mode, for confirming the selection.

Re-EQ: Depending on the listening mode, you can turn the cinema

re-equalization function on or off. [25]

Re-EQ (re-equalization) takes the edginess or “brightness” out of

your home cinema sound to compensate for the fact that sound

mixed for theaters may sound too bright when played back through

speakers in the home environment.

On: Select to turn on the re-equalization filter.

Off: Select to turn off the re-equalization filter.

Note:

The Re-EQ function is effective on the Dolby Pro Logic II Movie

and Dolby Digital modes.

SP A, SP B: For turning on and off speakers systems A and B. [26]

DISPLAY: For changing the display in the front display. [26]

DIMMER: Adjusts the display brightness.

There are three settings available: normal, dark and very dark.

MODE MACRO button [45]

For executing and programming the Macro function.

SETUP button [19, 20, 30-32]

Press to enter and exit the setup mode.

ENTER/cursor button [19, 20, 30-32]

For selecting and entering settings in the setup mode.

VOL

button

For adjusting the volume.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Here is explanation of how to connect the main components to the

TX-DS595 in the standard manner. There are many ways that any

one component can be connected, and it is up to you to decide which

method best fits your situation. The directions given here are only

one option and should only be thought of as such. It is best to fully

understand the nature of each connector and terminal as well as each

of your components and their features to ascertain which method of

connection is best.

• Insert all plugs and connectors securely. Improper

connections can result in noise, poor performance, or

damage to the equipment.

Improper connection

• Be sure to always refer to the instructions that came with the

component that you are connecting.

Inserted completely

• Do not plug in the power cord until all connections have been

made.

• When using one of the optical input jacks, remove the

protective cap and keep it safely. When the jack is not used,

replace the protective cap.

• For input jacks, red connectors (marked R) are used for the

right channel, white connectors (marked L) are used for the

left channel, and yellow connectors (marked V) are used for

video connection.

• When using an optical input jack, always use an optical fiber

cable.

• Do not bind audio/video connection cables with power cords

and speaker cables. Doing so may adversely affect the

picture and sound quality.

Optical digital input terminal

An optical digital input terminal is equipped

with a protection cap. When connecting,

remove this cap. When not using, put the

cap back on the terminal.

• When using the digital inputs, make sure to also connect the

analog connections whenever possible.

Connecting your video

Connecting antennas [17]

components [12]

Connect to devices with

Cautions regarding the AC

z terminals [13]

Connecting speakers [15]

OUTLETS connectors [14]

FRONT

CENTER

SPEAKER

SURROUND

SPEAKERS

ANTENNA

SPEAKERS

MONITOR

OUT

DVD

VIDEO 1

OUT IN

VIDEO2 VIDEO3

IN IN

VIDEO

REMOTE

CONTROL

S VIDEO

FRONT

SPEAKERS

PHONO CD

TAPE

OUT

AV RECEIVER

AC OUTLETS

MODEL NO. TX-DS595

AC 230-240V

SWITCHED

50 Hz

CAUTION

TOTAL 100W MAX.

SEE INSTRUCTION MANUAL

FOR CORRECT SETTING.

FRONT

SURR

CENTER

OPTICAL

COAXIAL

GND

6 OHMS

MIN.

/SPEAKER

4 OHMS

MIN.

/SPEAKER

SUB

SET BEFORE POWER ON

IMPEDANCE SELECTOR

SUBWOOFER

PRE OUT

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

Connecting a

subwoofer [15]

Connect to devices with

multichannel output [14]

Connecting your audio

components [11]

Default setting

Input source

DVD

Digital input

COAX 1

COAX 2

----

Multichannel

Yes

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

TAPE

OPT 2

----

120V

VOLTAGE

SELECTOR

220-230V

Voltage

selector [5]

----

PHONO

----

OPT 1

For worldwide models only

COAX: Coaxial OPT: Optical ----: No setting

: Not applicable

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

: Signal flow

Audio connection cable

Left (White)

Analog audio output

L (White)

Right (Red)

R (Red)

2. CD player

(CD)

ANTENNA

Digital audio output (optical)

MONITOR

OUT

DVD

VIDEO 1

OUT IN

VIDEO2 VIDEO

IN IN

Analog audio output

L (White)

REMOTE

CONTROL

1.Turntable

(PHONO)

PHONO CD

TAPE

OUT

R (Red)

FRONT

SURR

CENTER

OPTICAL

COAXIAL

Ground wire (earth)

GND

SUB

Analog audio input

L (White)

SUBWOOFER

PRE OUT

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

3.Tape deck, MD recorder,

DAT deck, CD recorder,

(TAPE)

R (Red)

L (White)

R (Red)

Analog audio output

With the initial settings of the TX-DS595, the CD input source is

set for digital input at the OPTICAL 1 jack.

Connecting your audio components

Below is an example of how you can connect your audio

components to the TX-DS595. Refer to the diagram above for the

following connection examples.

If the digital connection is made at a different jack, this must be

changed at the setup menu: Input Setup → Audio Setup → Digital

Input (see page 29).

1. Connecting a turntable (PHONO)

3. Connecting a cassette tape deck, MD recorder, DAT

deck, or CD recorder (TAPE)

Using an RCA-type audio connection cable, connect the output

terminal on the turntable to the PHONO input jacks on the TX-

DS595. Make sure that you properly connect the left channel to the L

jack and the right channel to the R jack.

Using an RCA-type audio connection cable, connect the output

terminals (PLAY) of the device to the TAPE IN jacks on the TX-

DS595 and the input terminals (REC) to the TAPE OUT jacks. Make

sure that you properly connect the left channel to the L jack and the

right channel to the R jack.

Note:

The TX-DS595 is designed for use with moving magnet cartridges.

For proper operation, connect a ground (or earth) wire to the GND

terminal. For some turntables, however, connecting the ground wire

may cause increased noise, and in such a case, a ground wire is not

necessary and should not be connected.

If the device has a digital output jack as well, be sure to also connect

it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT

(OPTICAL) jack on the TX-DS595 depending on the type of

connector on the device.

With the initial settings of the TX-DS595, the TAPE input source

is set for no digital input.

2. Connecting a compact disc player (CD)

If you connect the device to the DIGITAL INPUT terminal, then this

input source must be set for digital input at the setup menu: Input

Setup → Audio Setup → Digital Input (see page 29).

Using an RCA-type audio connection cable, connect the output

terminal on the compact disc player to the CD input jacks on the TX-

DS595. Make sure that you properly connect the left channel to the L

jack and the right channel to the R jack.

If the compact disc player has a digital output jack as well, be sure to

also connect it to either a DIGITAL INPUT (COAXIAL) or

DIGITAL INPUT (OPTICAL) jack on the TX-DS595 depending on

the type of connector on the compact disc player.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

MONITOR

OUT

DVD

VIDEO 1

OUT IN

VIDEO2 VIDEO3

IN IN

Video output

VIDEO

S video

REMOTE

CONTROL

S video output

4. DVD player

(DVD)

S V

IDEO

VIDEO

NO CD

TAPE

OUT

L (White)

R (Red)

Analog audio output

S video output

L (White)

R (Red)

FRONT

SURR

CENTER

OPTICAL

COAXIAL

Digital audio output

(Coaxial)

Analog audio output

5. VCR (VIDEO 1)

SUB

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

Digital audio output (Coaxial)

Video input

S video input

R (Red)

: Signal flow

Analog audio input

L (White)

Audio connection cable

Left (White)

Video connection cable

S Video connection cable

Right (Red)

Video output

S video output

MONITOR

OUT

DVD

VIDEO 1

OUT IN

VIDEO2 VIDEO3

IN IN

7.TV monitor or Projector

(MONITOR OUT)

Video input

6. Satelite tuner,TV,

or settop box

(VIDEO 2 / VIDEO 3)

VIDEO

L (White)

R (Red)

S video input

REMOTE

CONTROL

S VIDEO

Analog audio output

NO CD

TAPE

OUT

FRONT

SURR

CENTER

OPTICAL

COAXIAL

SUB

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

Digital audio output (optical)

If the device has a digital output jack as well, be sure to also connect

it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT

(OPTICAL) jack on the TX-DS595 depending on the type of

connector on the DVD player.

Connecting your video components

Below is an example of how you can connect your video

components to the TX-DS595. Refer to the diagram above for the

following connection examples.

With the initial settings of the TX-DS595, the DVD input source

is set for digital input at the COAXIAL 1 jack.

The flow of the video signals is as follows:

If the digital connection is made at a different jack, this must be

changed at the setup menu: Input Setup → Audio Setup → Digital

Input (see page 29).

• The signal that comes in from VIDEO IN is sent to VIDEO

OUT.

• The signal that comes in from S VIDEO IN is sent to S VIDEO

OUT

5. Connecting a video cassette recorder (VIDEO 1)

If the video cassette recorder is equipped with an S video output

terminal, connect it to the S VIDEO 1 IN terminal with an S video

cable. If it does not have an S video output terminal, connect its

video output terminal to the VIDEO 1 IN terminal using an RCA-

type video connection cable. You do not need to connect to both the

S VIDEO 1 IN and VIDEO 1 IN terminals.

4. Connecting a DVD player (DVD)

If the device is equipped with an S video output terminal, connect it

to the DVD S VIDEO IN terminal with an S video cable. If it does

not have an S video output terminal, connect its video output

terminal to the DVD VIDEO IN terminal using an RCA-type video

connection cable. You do not need to connect to both the DVD S

VIDEO IN and DVD VIDEO IN terminals.

Using an RCA-type audio connection cable, connect the audio

output terminal on the video cassette recorder to the same VIDEO 1

IN audio jacks on the TX-DS595 and audio input terminal to the

VIDEO 1 OUT audio jacks. Make sure that you properly connect the

left channel to the L jack and the right channel to the R jack.

Using an RCA-type audio connection cable, connect the audio

output terminal on the device to the audio DVD IN jacks on the TX-

DS595. Make sure that you properly connect the left channel to the L

jack and the right channel to the R jack.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

If the device has a digital output jack as well, be sure to also connect

it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT

(OPTICAL) jack on the TX-DS595 depending on the type of

connector on the device.

Connect to devices with z terminals

The z terminal on the TX-DS595 is for connecting other Onkyo

components equipped with the same z terminal. When a

component are z-connected, you can point the remote controller

supplied with the TX-DS595 at the sensor on the TX-DS595 and

operate that component without having to switch remote controllers.

With the initial settings of the TX-DS595, the VIDEO 1 input

source is set for digital input at the COAXIAL 2 jack.

If the digital connection is made at a different jack, this must be changed

at the setup menu: Input Setup → Audio Setup → Digital Input (see

page 29).

In addition, by connecting components to the z terminal, you can

also perform the system operations given below.

Power on/ready function

6. Connecting a satellite tuner, television, or settop box

(VIDEO 2/3)

When the TX-DS595 is in the standby state, if an z-connected

component is turned on, then the TX-DS595 also turns on and the

input source selected at the TX-DS595 automatically switches to

that component.

If the power cord for an z-connected component is connected to

the AC OUTLET on the TX-DS595, or if the TX-DS595 is turned

on, this function will not work.

If the device is equipped with an S video output terminal, connect it

to the S VIDEO 3 IN terminal with an S video cable. If it does not

have an S video output terminal, connect its video output terminal to

the VIDEO 3 IN terminal using an RCA-type video connection

cable. You do not need to connect to both the S VIDEO 3 IN and

VIDEO 3 IN terminals.

Using an RCA-type audio connection cable, connect the audio

output terminal on the satellite tuner or television to the same

VIDEO 3 IN audio jack on the TX-DS595. Make sure that you

properly connect the left channel to the L jack and the right channel

to the R jack.

Direct change function

When the play button is pressed at an z-connected component, the

input source selected at the TX-DS595 automatically changes to that

component.

If the device have a digital output jack as well, be sure to also

connect it to either a DIGITAL INPUT (COAXIAL) or DIGITAL

INPUT (OPTICAL) jack on the TX-DS595 depending on the type of

connector on the device.

Power off function

When the TX-DS595 is placed in the standby state, all z-

connected components are also automatically put into the standby

state.

With the initial settings of the TX-DS595, the VIDEO 3 input

source is set for digital input at the OPTICAL 2 jack.

CAUTION

If the digital connection is made at a jack different from the initial

settings, this must be changed at the setup menu: Input Setup →

Audio Setup → Digital Input (see page 29).

If an MD recorder is connected to the TAPE jack on the TX-DS595,

switch the Input Selector from TAPE to MD (see page 16).

You can also connect the device to the VIDEO 2 IN input jacks on

the TX-DS595 just like you can to the VIDEO 3 IN input jacks.

TX-DS595

REMOTE

CONTROL

With the initial settings of the TX-DS595, the VIDEO 2 input

source is set for no digital input.

z connector

If you connect the device to the DIGITAL Input terminal, then this

input source must be set for digital input at the setup menu: Input

Setup → Audio Setup → Digital Input (see page 29).

Ex: Onkyo CD player

z connector

7. Connecting a television monitor or projector

(MONITOR OUT)

If the monitor or projector is equipped with an S video output

terminal, connect it to the MONITOR OUT S VIDEO terminal with

an S video cable. If it does not have an S video output terminal,

connect its video output terminal to the MONITOR OUT VIDEO

terminal using an RCA-type video connection cable. You do not

need to connect to both the MONITOR OUT S VIDEO and

MONITOR OUT VIDEO terminals.

Ex: Onkyo cassette tape deck

To connect components using the z terminal, simply connect a

remote control cable from this z terminal to the z terminal of the

other component. An z remote control cable with a 1/8-inch (3.5-

mm) miniature two-conductor plug comes with every cassette tape

deck, compact disc player, MD recorder, and DVD player that has an

z terminal.

• For remote control operation, the audio connection cables must

also be connected.

• The RC-447M remote controller does not support turntables.

• If a component has two z terminals, you can use either one to

connect to the TX-DS595. The other one can be used to daisy

chain with another component.

• With Onkyo DVD players, you can enter the pre-program code

so that you can operate the DVD player directly with the remote

controller without connecting the z terminals (see page 38).

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connect to devices with multichannel output

Cautions regarding the AC OUTLETS

connectors

By connecting a DVD player, MPEG decoder, or other component

that has a multi channel port, you can playback the audio with 5.1

channel output. So, be sure to prepare a cable that can properly

connect the TX-DS595 to the peripheral device.

The TX-DS595 is supplied with AC mains outlets for connecting

the power cords from other devices so that their power is supplied

through the TX-DS595. By doing this, you can use the STANDBY/

ON button on the TX-DS595 to turn on and off the connected

devices as well.

TX-DS595 MULTI CHANNEL INPUT

The shape, number, and total capacity of the AC outlets may

differ depending on the area of purchase.

FRONT

SURR

CENTER

OPTICAL

COAX

GND

Caution:

SUB

Make sure that the total capacity of the other components connected

to this unit does not exceed the capacity that is printed on the rear

panel (e.g., 120 watts).

SUBWOOFER

PRE OUT

WOOFER

MULTI

CHANNEL INPUT

DIGITAL INPUT

AC OUTLET

SWITCHED

100W MAX.

Front output

Center output

Subwoofer output

Surround output

AC OUTLETS

AC 230-240V

50Hz

SWITCHED

TOTAL 100W MAX.

DVD Player/MPEG decoder

ex. European and

some Asian models

ex. USA and Canadian

models

Connecting speakers

Positioning speakers

Speaker placement plays an important role in the reproduction of

Surround sound. The placement of the speakers varies depending on

the size of the room and the wall coverings used in the room. The

illustration shows an example of a layout for standard speaker

placement. Refer to this example when you position the speakers in

order to experience the best of Surround sound.

TV or Screen

Front

left

speaker

Front

right

speaker

Sub-

woofer

Center

speaker

Standard speaker placement

For ideal Surround effects, all speakers should be installed. If a

center speaker or subwoofer is not connected, the sound from the

unused channel is properly distributed to the connected speakers in

order to produce the best Surround sound possible.

Surround

left

speaker

Surround

right

speaker

Front: The left, right, and center speakers should face the seated

listener and be placed at ear level. The center speaker produces a

richer sound image by enhancing the perception of the sound’s

source and movement.

Listener

Surround: Place the left and right Surround speakers 3 feet (1

meter) above the listener’s ear level and facing toward the sides of

the room, making sure that the listener is within the speakers’ dis-

persion angle. These speakers produce the feel of a moving sound

while creating the sensation of being in the middle of the action.

Subwoofer: Install a subwoofer with a built-in power amplifier for

powerful bass sounds. The placement of the subwoofer does not

affect the final quality of the sound image too much, so you can

install it with the room layout in mind.

Refer to the speaker’s instruction manual for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting speakers

• Be sure to connect the positive and negative cables for the

speakers properly. If they are mixed up, the left and right signals

will be reversed and the audio will sound unnatural.

Connecting speakers

1. Check the impedance of the speakers you are

connecting.

• Do not connect more than one speaker cable to one speaker

terminal. Doing so may damage the TX-DS595.

The TX-DS595 requires speakers with an impedance of 4 Ω or

greater. Connecting speakers with an impedance of less than 4 Ω

may damage the TX-DS595.

• Use FRONT SPEAKERS B terminals to connect a second pair

of front speakers.

• When you listen to surround audio or select Multichannel, be

2. Set the IMPEDANCE SELECTOR switch according to

the impedance of the speakers being connected.

sure to turn on SPEAKERS A.

If all speakers have an impedance of 6 Ω or greater, slide the

IMPEDANCE SELECTOR switch to the left (6 OHMS MIN./

SPEAKER). If one or more speakers have an impedance of less

than 6 Ω, slide the IMPEDANCE SELECTOR switch to the

right (4 OHMS MIN./SPEAKER).

Connecting the speaker cable

1. Strip away 5/8 inch (15 mm) of wire insulation.

2. Twist wire ends very tight.

3. Unscrew

6 OHMS

MIN.

/SPEAKER

4 OHMS

MIN.

/SPEAKER

6 OHMS

MIN.

/SPEAKER

4 OHMS

MIN.

/SPEAKER

SET BEFORE POWER ON

IMPEDANCE SELECTOR

4. Insert wire

4 Ω or above/speaker

6 Ω or above/speaker

Notes:

5. Screw

• The power to the TX-DS595 must not be turned on when

changing the IMPEDANCE SELECTOR setting.

15mm

(5/8")

• When you are using only one

speaker or when you wish to

listen to monaural (mono)

NO!

sound, a single speaker should

never be connected in parallel to

both the right and left-channel

terminals simultaneously.

Connecting a subwoofer

–

Use the PRE OUT SUBWOOFER jack to connect a subwoofer with

a built-in power amplifier. If your subwoofer does not have a built-in

amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack

and the subwoofer to the amplifier.

• To prevent damage to circuitry,

never short-circuit the positive

(+) and negative (–) speaker

wire.

NO!

Surround

right

speaker

Surround

left

speaker

Front right

speaker A

Front left

speaker A

FRONT

CENTER

SPEAKER

SURROUND

SPEAKERS

ANTENNA

SPEAKERS

MONITOR

OUT

DVD

VIDEO 1

OUT IN

VIDEO2 VIDEO3

VIDEO

REMOTE

CONTROL

S VIDEO

FRONT

SPEAKERS

PHONO CD

TAPE

OUT

AV RECEIVER

MODEL NO. TX-DS595

AC OUTLETS

AC 230-240V 50 Hz

SWITCHED

TOTAL 100W MAX.

CAUTION

SEE INSTRUCTION MANUAL

FOR CORRECT SETTING.

FRONT

SURR

CENTER

OPTICAL

COAXIAL

GND

OHMS

MIN.

/SPEAKER

SUB

SET BEFORE POWER ON

SUBWOOFER

PRE OUT

WOOFER

MULTI

IMPEDANCE SELECTOR

CHANNEL INPUT

DIGITAL INPUT

Center

speaker

Front right

speaker B

Front left

speaker B

Subwoofer

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the power

SEND/LEARN

indicator

D/L

STANDBY indicator

STANDBY/ON

STDBY

RCVR MODE

SPEAKERS

CH LEVEL

MASTER VOLUME

DISC

VOL

STANDBY/ON

SETUP

DSP/MODE ADJ

AUDIO

MUTING

STANDBY

POWER

RETURN

ANGLE

SUBTITLE

TV/VCR

LEVEL

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

RANDOM

REC

OPEN CLOSE

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

DVD

AV RECEIVER TX DS595

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Re-EQ

POWER

DISPLAY

DIMMER

ZONE

To wall outlet

+10

-- ---

ENTER

HOME THEATER CONTROLLER

RC-447M

• The TX-DS595 is shipped with the main power (POWER)

To change the display of the input source from TAPE to

MD:

If you connected an MD recorder to the TAPE jack on the TX-

DS595, you can have “MD” appear when the TAPE source button is

pressed. By changing the display, if an Onkyo MD recorder z-

connected, the z system functions will become enabled.

switch in the on position (

). When the power cord is

plugged in for the first time, the TX-DS595 will automatically

enter the standby state and the STANDBY indicator will light

(same condition after step 2 below).

• Before you plug in the TX-DS595, confirm that all connections

have been made properly.

• Turning on the power may cause a momentary power surge,

which might interfere with other electrical equipment on the

same circuit, such as computers. If this happens, use a wall outlet

on a different circuit.

Changing the display:

Press and hold down the TAPE source button until the display

changes from TAPE to MD (approx. 3 seconds).

TAPE

1. Plug the power cord into an AC wall outlet.

STANDBY

2. Press the POWER switch to set the

POWER

TX-DS595 to standby state.

To return the display to its original setting, perform the same

procedure. This setting is necessary to allow z system functions

for the connected cassette tape or MD recorder.

The STANDBY indicator will light up.

OFF

STANDBY/ON

3. Press the STANDBY/ON button to

turn on the TX-DS595. The display

and four jog dial indicators will light

up and the STANDBY indicator will

turn off.

Memory preservation

This unit does not require memory preservation batteries. A built-

in memory power backup system preserves the contents of the

memory during power failures and even when the POWER

switch is set to off. The POWER switch must be set to on in order

to charge the backup system.

STANDBY

Turn off

If you press the STANDBY/ON button

again, the receiver returns to Standby mode.

The memory preservation period after the unit has been turned off

varies depending on climate and placement of the unit. On the

average, memory contents are protected over a period of a few

weeks after the last time the unit has been turned off. This period

is shorter when the unit is exposed to a highly humid climate.

Turning the power on from the remote controller:

Before you can use the remote controller, you must perform steps 1

and 2 above and place the TX-DS595 in the standby state.

1. Press the RCVR MODE button.

The RCVR MODE button lights green.

2. Press the ON button to turn on the

TX-DS595 (take it out of the standby

state).

To return the TX-DS595 to the standby

state, press the STDBY button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting antennas

To use the tuner of TX-DS595, it is necessary to prepare the supplied

FM and AM antennas.

Connecting the included antennas

Connecting the FM indoor antenna:

• Adjustment and placement of the FM and AM antennas for

better reception must be done while listening to a station

broadcast.

The FM indoor antenna is for indoor use only. During use, extend the

antenna and move it in various directions until the clearest signal is

received. Fix it with push pins or similar implements in the position

that will cause the least amount of distortion.

If the reception is not very clear with the attached FM indoor

antenna, the use of an outdoor antenna is recommended.

• If better reception cannot be obtained, then placement of an

outside antenna is recommended.

Connecting the AM loop antenna:

Assembling the AM loop antenna

The AM loop antenna is for indoor use only. Set it in the direction

and position where you receive the clearest sound. Put it as far away

as possible from the TX-DS595, televisions, speaker cables, and

power cords.

Assemble the loop antenna as shown in the illustration.

• Refer to “Connecting the AM loop antenna” below for details on

When reception is not satisfactory with the attached AM loop

antenna alone, connection of an outdoor antenna is recommended.

connecting the loop antenna.

FM antenna

(Indoor) AM loop antenna

Other

models

Insert into the hole.

USA and

Canadian

models

ANTENNA

Connecting the AM antenna cable

1. Press down the lever.

2. Insert the wire into the hole.

3. Release the lever.

Strip away the insulation from the end of

the cable, then fully insert the stripped

end of the cable.

Hint:

Either of the split ends of the AM antenna can be connected to either

terminal. Unlike speaker cabling, there is no polarity for AM

broadcast signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting antennas

Connecting an FM outdoor antenna

Directional linkage

Please make sure that you follow the considerations:

Do not use the same antenna for both FM and TV (or VCR)

reception since the FM and TV (or VCR) signals can interfere with

each other. If you must use a common FM/TV (or VCR) antenna, use

a directional linkage type splitter.

• Keep the antenna away from noise sources (neon signs, busy

roads, etc.).

• It is dangerous to put the antenna close to power lines. Keep it

well away from power lines, transformers, etc.

• To avoid the risk of lightning and electrical shock, grounding is

necessary. Follow item 14 of the “Important Safeguards” on

page 2 when you install the outdoor antenna.

To receiver

To TV (or VCR)

ANTENNA

Connecting the antenna cable to the 75/300 Ω

antenna adapter (For all models other than USA,

Canadian and European models)

Connecting the 300 Ω ribbon wire:

Loosen the screws and wrap the wire around these screws. Then

tighten the screws with a screwdriver.

Outdoor

antenna

Connecting an AM outdoor antenna

An outdoor antenna will be more effective if it is stretched

horizontally above a window or outside.

300 Ω

ribbon wire

• Do not remove the AM loop antenna.

• To avoid the risk of lightning and electrical shock, grounding is

necessary. Follow item 14 of the “Important Safeguards” on

page 2 when you install the outdoor antenna.

Connecting the coaxial cable:

1. With your fingernail, or a small screwdriver, press the

stoppers of the 75/300 Ω antenna adapter outward

and remove the cover.

Outdoor antenna

2. Remove the transformer wire A from slit B and insert

it into slit C.

3. Prepare the coaxial cable as shown in the diagram.

4. Connect the 75/300 Ω antenna adapter to the coaxial

cable.

1. Insert the end of the cable.

2. Clamp it in place with pliers.

ANTENNA

(Indoor)

AM loop antenna

5. Reinstall the cover.

3, 4

mm mm mm

Slit B

15mm

5/8"

Wire A

Note:

Slit C

If you are using the TX-DS595 worldwide model in a region where

AM frequencies are delineated by 10-kHz steps, be sure to set the

AM Freq Step Setup setting accordingly (see page 32).

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker setup

Follow the steps below before you start operating the unit.

SETUP

RETURN

ENTER

SPEAKERS

CH LEVEL

MASTER VOLUME

DISC

VOL

STANDBY/ON

SETUP

DSP/MODE ADJ

AUDIO

MUTING

STANDBY

POWER

RETURN

ANGLE

SUBTITLE

TV/VCR

LEVEL

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

RANDOM

REC

OPEN CLOSE

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

DVD

AV RECEIVER TX DS595

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Re-EQ

Jog dial and indicators

RETURN

DISPLAY

DIMMER

ZONE

+10

-- ---

ENTER

HOME THEATER CONTROLLER

RC-447M

DSP/MODE ADJ

Then turn the jog dial or press the or cursor

button on the remote controller to set the size of

your front speakers.

Speaker Configuration

PUSH TO ENTER

These settings tell the TX-DS595 which speakers you have

connected and what size they are.

LARGE: Select if the front speakers are large sized.

SMALL: Select if the front speakers are small sized.

Remote

controller

1. Press the SETUP button.

TX-DS595

• If “NO” is selected for the Subwoofer setting, then this setting is

fixed to “LARGE”.

SETUP

DSP/MODE ADJ

6. Press either the jog dial or the

cursor button on the remote controller

once.

PUSH TO ENTER

DSP/MODE ADJ

If anything other than “1. SPEAKER SETUP”

appears, turn the jog dial or press the and

cursor buttons on the remote controller until “1.

SPEAKER SETUP” appears.

PUSH TO ENTER

DSP/MODE ADJ

Then turn the jog dial or press the or cursor

buttons on the remote controller to set whether

or not a center speaker is connected and, if one

PUSH TO ENTER

is connected, its size.

The display changes as follows: “1. SPEAKER SETUP” → “2.

NONE: Select if no center speaker is connected.

LARGE: Select if the center speaker is large sized.

SMALL: Select if the center speaker is small sized.

INPUT SETUP” → “3. PREFERENCE.”

* If the indicators directly above and below the jog dial are lit,

turning the jog dial selects a group of settings and pushing the jog

dial enters the selected group (i.e. takes you one level down).

•

If “SMALL” is selected for the Front setting, then “LARGE”

cannot be selected for this setting.

DSP/MODE ADJ

2. Press the jog dial or ENTER button on

7. Press either the jog dial or the

cursor button on the remote controller

once.

the remote controller.

PUSH TO ENTER

DSP/MODE ADJ

3. Press the jog dial or ENTER button on

DSP/MODE ADJ

Then turn the jog dial or press the or cursor

button on the remote controller to set whether

or not surround speakers are connected and, if

they are connected, their size.

the remote controller.

PUSH TO ENTER

DSP/MODE ADJ

NONE: Select if no surround left and right speakers are connected.

LARGE: Select if the surround left and right speakers are large

sized.

SMALL: Select if the surround left and right speakers are small

sized.

4. Turn the jog dial or press the or

cursor buttons on the remote

controller to set whether or not a

subwoofer is connected.

PUSH TO ENTER

YES: Select when a subwoofer is connected.

NO: Select when a subwoofer is not connected.

•

If “SMALL” is selected for the Front setting, then “LARGE”

cannot be selected for this setting.

* If the indicators directly to the left and right of the jog dial are lit,

turning the jog dial changes the setting of the currently selected

parameter and pushing the jog dial displays the next parameter.

Pressing the jog dial again or cursor button returns you to the

subwoofer setting.

RETURN

8. Press the RETURN button.

DSP/MODE ADJ

5. Press either the jog dial or the

You return to the “SPEAKER CONFIG?”

display.

cursor button on the remote controller

once.

PUSH TO ENTER

Notes:

•

If you press the RETURN button again, you go back up one more

level.

•

To exit the setup mode immediately, press the SETUP button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Speaker setup

Speaker Distance

Level Calibration

These settings tell the TX-DS595 how far away your speakers are

located from the listening position so that it can provide the optimum

sound space. If you are continuing from setting the speaker

configuration and are still in the setup mode, skip directly to step 2.

These settings allow you to set the volume levels of each speaker

individually so that they all sound at the same level when heard from

the listening position. If you are continuing from setting the speaker

distances and are still in the setup mode, skip directly to step 2.

SETUP

1. Press the SETUP button.

If anything other than “1. SPEAKER SETUP”

SETUP

appears, turn the jog dial or press the and

cursor buttons on the remote controller until “1.

SPEAKER SETUP” appears.

DSP/MODE ADJ

cursor buttons on the remote controller until “1.

SPEAKER SETUP” appears.

DSP/MODE ADJ

PUSH TO ENTER

DSP/MODE ADJ

2. Press the jog dial or the ENTER button

on the remote controller.

DSP/MODE ADJ

2. Press the jog dial or the ENTER button

PUSH TO ENTER

on the remote controller.

DSP/MODE ADJ

Then turn the jog dial or press the

cursor

PUSH TO ENTER

button on the remote controller to display the

DSP/MODE ADJ

Then turn the jog dial or press the

cursor

“LEVEL CAL.”

PUSH TO ENTER

button on the remote controller to display

“SPEAKER DISTANCE.”

PUSH TO ENTER

DSP/MODE ADJ

3. Press the jog dial or ENTER button on

the remote controller.

DSP/MODE ADJ

3. Press the jog dial or the ENTER button

on the remote controller.

A test sound (pink noise) will be heard from the

left front speaker. At this point, it is not

necessary to adjust the volume of the test

sound.

PUSH TO ENTER

DSP/MODE ADJ

Then turn the jog dial or press the and

cursor buttons on the remote controller to

select the unit of measurement.

PUSH TO ENTER

DSP/MODE ADJ

4. Press either the jog dial or the

cursor button on the remote controller

again.

PUSH TO ENTER

FEET: Select if you will enter the distances in feet.

METERS: Select if you will enter the distances in meters.

The test sound will now be heard from a

different speaker.

DSP/MODE ADJ

4. Press the jog dial or the cursor

DSP/MODE ADJ

button on the remote controller.

5. Turn the jog dial or press the or

cursor buttons on the remote

controller to adjust the volume of the

test sound from this speaker to the

same level that you heard from the

previous speaker.

PUSH TO ENTER

DSP/MODE ADJ

Then turn the jog dial or press the and

cursor buttons on the remote controller to set

the distance from the front speakers to the

listening position.

PUSH TO ENTER

You can adjust the level in the range between -12 dB and +12 dB.

6. Repeat the procedure in step 4 and 5 until the volume of

the test sound from all speakers is the same level.

You can set the distance in the range of 1 feet (0.3 m) - 30 feet (9 m)

in 1 feet (0.3 m) steps.

Each time you press the jog dial or the

button on the remote

controller, the test sound will be heard from a different speaker. The

speaker order for calibration is LEFT (front left) → CENTER

(center) → RIGHT (front right) → SURR RIGHT (surround right)

→ SURR LEFT (surround left) → SUBWOOFER (subwoofer).

5. Repeat the procedure in step 4 to set the distance from

the center speaker (CENTER) and the surround speakers

(SURR L/R) to the listening position.

RETURN

7. Press the RETURN button.

RETURN

6. Press the RETURN button.

You return to the “LEVEL CAL?” display.

You return to the “SP DISTANCE?” display.

Notes:

•

If you press the RETURN button again, you go back up one more

level.

•

If you press the RETURN button again, you go back up one more

level.

•

To exit the setup mode immediately, press the SETUP button.

•

To exit the setup mode immediately, press the SETUP button.

You can also press the TEST button on the remote controller to perform

the Level Calibration setting. For more details, see page 9.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to Radio Broadcasts

TUNING

FM MODE

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

STANDBY

POWER

RETURN

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

AV RECEIVER TX DS595

FM AM

One of the features of the TX-DS595 that is most frequently used is

its ability to play FM and AM broadcast radio stations. The TX-

DS595 provides a number of listening modes perfect for listening to

the radio and getting the most out of your audio system. Also, by

presetting radio stations that you listen to frequently, you can select

Listening to a stereo radio station (FM mode)

When you tune into a radio station, TUNED

FM MODE

indicator appears in the display. If you tune into

an FM station in stereo, then “FM STEREO”

appears. If the signal is weak, it may be

impossible to tune into the station in stereo. In

such a case, press the FM MODE button on the

front panel. The FM MUTE indicator turns off.

At this time, the station will be in mono and

interstation noise will be heard.

them easily by pressing the CH

button on the remote controller.

Tuning into a radio station

1. Press either the AM or FM input

source button.

TUNING

2. Using the TUNING and buttons

on the front panel, tune into the

station you desire.

FM MUTE

Tuned in stereo

“FM STEREO”

(Lights red)

FM MUTE

TUNED

FM STEREO

Band

Frequency

• The tuner frequency changes in 50 kHz increments for FM

and 10 kHz (or 9kHz) increments for AM.

• When tuning into FM stations, you can press the TUNING

or button continuously for more than 0.5 seconds to scan

for an FM station in the direction of the button you pressed

(FM auto tuning mode). After you release the button and a

station is received in stereo, the scanning stops.

• The European model allows you to receive RDS broadcasts.

See pages 23 and 24 for a more detailed explanation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to Radio Broadcasts

D/L

PRESET

RCVR

MODE

SPEAKERS

CH LEVEL

MASTER VOLUME

DISC

VOL

STANDBY/ON

SETUP

DSP/MODE ADJ

AUDIO

MUTING

STANDBY

POWER

RETURN

ANGLE

SUBTITLE

TV/VCR

LEVEL

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

RANDOM

REC

OPEN CLOSE

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

DVD

AV RECEIVER TX DS595

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Re-EQ

FM AM

PRESET MEMORY

Jog dial

DISPLAY

DIMMER

ZONE

+10

-- ---

ENTER

HOME THEATER CONTROLLER

RC-447M

Presetting a radio station

Selecting a preset radio station

1. Tune into the radio station you desire (see “Tuning

1. Press either the AM or FM input

source button. The front display

into a radio station” ).

should show the currently selected

frequency.

If it displays the listening mode, press the DISPLAY button to

display the frequency.

PRESET MEMORY

2. Press the PRESET MEMORY button

PRESET

on the front panel.

2. Press the PRESET

button and

“PRESET IN?” appears in the front display

for about five seconds.

select the number of the desired

preset station.

When using the remote controller:

1. Press the RCVR MODE button.

The RCVR MODE button lights green.

DSP/MODE ADJ

3. Press the jog dial.

2. Press the TUN button.

The MEMORY indicator lights red.

3. Press the CH

button and select the number of the

PUSH TO ENTER

“MEMORY”

(Lights red)

desired preset station.

MEMORY

Erasing a preset radio station

1. Press the AM or FM button and press the PRESET

button to select the preset radio station that you

want erase (see above).

DSP/MODE ADJ

4. Turning the jog dial, select a preset

number (from 1 to 40) to assign the

station to be preset.

PUSH TO ENTER

“MEMORY”

(Lights red)

Flash

PRESET MEMORY

2. Press the PRESET MEMORY button.

TUNED

MEMORY

“PRESET IN?” appears.

DSP/MODE ADJ

5. Press the jog dial to finalize the

DSP/MODE ADJ

3. Turn the jog dial to display “PRESET

procedure.

ERASE?”

This programs the radio station as a preset

radio station.

PUSH TO ENTER

• Up to 40 stations can be stored in memory

as preset radio stations.

DSP/MODE ADJ

4. Press the jog dial.

The selected preset station is erased.

PUSH TO ENTER

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to RDS broadcasts

(European models only)

Listening to RDS broadcasts

PTY program types in Europe

RDS reception is available only on the European model and only in

areas where RDS broadcasts are available.

The text given in parenthesis is what is actually displayed on the TX-

DS595.

What is RDS?

None (NONE):

RDS stands for Radio Data System and is a type of FM broadcasting.

RDS was developed within the European Broadcasting Union

(EBU) and is available in most European countries. Many FM

broadcasting stations now transmit the RDS signals, which provide

the additional information required. RDS provides you with various

services so that you can choose a station that broadcasts your

favorite categories of music, news, or other information.

No program type.

News reports (NEWS):

Reports on current events and happenings.

Current affairs (AFFAIRS):

Topical reporting of current affairs, often with a wider range of

topics than news reports.

There are three main classifications of RDS broadcasts. Though they

can be tuned into by using the Tuning buttons as normal stations,

RDS broadcasts allow you to scan for stations of the type and

classification for which you are looking. This makes it much easier

for you to find the station you want (see “Performing a PTY scan”

and “Performing a TP scan” on page 24). The three main

classifications are explained below.

Information (INFO):

General information such as weather forecasts, consumer affairs,

medical help, etc.

Sport (SPORT):

Live sports action, sports news, and interviews.

RT: Radio Text

Education (EDUCATE):

When an RDS station broadcasting RT information is selected, the

Formal educational programs.

text information received from the station is displayed.

Drama (DRAMA):

PTY: Program Type

Radio plays and serials.

When an RDS station broadcasting PTY information is selected, the

station type (classification) is displayed.

Culture (CULTURE):

Cultural programs (including religious affairs).

TP: Traffic Program

When an RDS station broadcasting TP information is selected,

traffic information will be broadcasted periodically.

Science and technology (SCIENCE):

Programs about the natural sciences and technology.

Varied (VARIED):

Speech-based programs not covered by the above categories (e.g.,

quizzes, panel games, and comedy).

Notes:

• In some cases, the characters displayed on the display of the TX-

DS595 may not be exactly the same as the ones broadcast by the

radio station. Also, unusual characters may appear on the display

if the TX-DS595 receives characters that cannot be displayed

correctly. This is not a malfunction.

Pop music (POP M):

Popular commercial music, usually from past or present sales charts

(e.g., Top 40).

• When an RDS station broadcasting PS information is selected,

the name of the station is displayed instead of the frequency.

Rock music (ROCK M):

Popular music with an alternative appeal, often not appearing on

sales charts.

Middle of the road music (M.O.R. M):

Easy listening music (as opposed to Pop, Rock, or Classical).

Light classics (LIGHT M):

Classical music for general rather than specialist appreciation.

Serious classics (CLASSICS):

Performances of major orchestral works, symphonies, chamber

music, etc. (including the Grand Opera).

Other music (OTHER M):

Music styles not covered by the above categories (e.g., Jazz, Rhythm

& Blues, Folk, Country, and Reggae).

• Alarm (ALARM):

When an RDS station is making an emergency broadcast, this

ALARM will flash on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Listening to RDS broadcasts

Jog dial

RT/PTY/TP

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

STANDBY

POWER

RETURN

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

AV RECEIVER TX DS595

DSP/MODE ADJ

4. Press the jog dial.

Displaying Radio Text (RT)

The TX-DS595 will scan until it reaches a

station of the program type you selected. It

will then stop briefly at that station before

continuing on until it reaches the next

station. Pressing the jog dial stops the PTY

scan at that point. If you press the RT/PTY/

TP while “NONE” is displayed, “PTY ?”

will appear. In this case, return to step 3.

If the station you are currently tuned into is broadcasting RT signals,

they will be displayed in the front display on the TX-DS595. If the

station does not, this function will be ignored.

PUSH TO ENTER

RT/PTY/TP

1. To display the radio text, press the

RT/PTY/TP button once.

• If the current station you are listening to is not an RDS station,

only the frequency of the station appears.

DSP/MODE ADJ

5. Press the jog dial when it reaches

the station that you want to listen to.

• If “WAITING” appears on the display, more time is required to

receive the RT information. When the information is received,

the characters will scroll across the front display.

“NOT FOUND” will appear when no RDS

signal is being received from the station.

PUSH TO ENTER

• If “NO TEXT DATA” appears on the display, RT information is

not available.

• The display shows the frequency for 3 seconds and returns to

program service name.

Performing a TP scan

1. Press the FM input source button.

Performing a PTY scan

RT/PTY/TP

1. Press the FM input source button.

2. Press the RT/PTY/TP button three

times.

RT/PTY/TP

2. Press the RT/PTY/TP button twice.

“< TP >” will appear if the current station is broadcasting TP

signals. This station will periodically broadcast traffic

information. To find a different station, proceed to the next step.

Also, if “TP” is displayed, proceed to the next step.

The current program type appears on the

display.

DSP/MODE ADJ

3. Press the jog dial.

DSP/MODE ADJ

The TX-DS595 will scan until it reaches a

station broadcasting traffic information. If

“NOT FOUND” appears on the display, a

3. Using the jog dial, select the PTY

program type you desire.

PUSH TO ENTER

TP station cannot be located.

PUSH TO ENTER

Download from Www.Somanuals.com. All Manuals Search And Download.

Enjoying music or videos with the TX-DS595

SPEAKERS A/B

Jog dial

MASTER VOLUME

DISPLAY

RCVR

MODE

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

DISC

VOL

STANDBY

POWER

RETURN

AUDIO

MUTING

PUSH TO ENTER

OFF

ANGLE

SUBTITLE

DISPLAY

DIMMER

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

MUTING

TV/VCR

LEVEL

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

RANDOM

REC

OPEN/CLOSE

AV RECEIVER TX DS595

DVD

T 1

TUN

Listening mode

buttons

Re-EQ

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Input source buttons BASS TREBLE

Re-EQ

SP A

DISPLAY

DIMMER

ZONE

+10

-- ---

ENTER

DISPLAY

HOME THEATER CONTROLLER

RC-447M

Basic operation

Selecting a listening mode

To use the remote controller, first press the RCVR button.

1. Press the desired input source button.

TX-DS595

Select your desired listening mode using the jog dial.

• Depending on the software that you are playing, SURROUND

will be Dolby Digital, DTS, or Dolby Pro Logic II.

• Refer to page 28 for more details of listening modes.

• Refer to page 30 for sources and listening modes.

DVD

VIDEO 1 VIDEO 2 VIDEO 3

TAPE

PHONO

VCR

• When playing Dolby Digital or DTS software, the listening

mode will automatically change to Dolby Digital or DTS.

• With Dolby Digital and Dolby Pro Logic II Movie, you can use

the Re-EQ function (for more details, see page 9).

Remote controller

Tip:

You can set in advance a different listening mode for each input

source. For more details, see page 30.

DSP/MODE ADJ

When turning the jog dial

The selected source name appears on the display. If you have

selected DVD, CD, or other digital devices, see “Digital Input”

on page 29. If you have selected a multichannel input, see

“Multichannel” on page 29 and “Enjoying the multichannel

input” on page 27.

The items change as shown below:

DIRECT ↔ STEREO ↔ SURROUND ↔

PUSH TO ENTER

ORCHESTRA ↔ UNPLUGGED ↔

STUDIO MIX ↔ TV LOGIC ↔ ALL CH

STEREO ↔ DIRECT...

SPA

SPEAKERS

2. Make sure that the SPEAKERS A

indicator is lit on the display. If it is

not lit, press the SPEAKERS A

button.

DSP/MODE ADJ

When pressing the jog dial

Each time you press it, the items change as

shown below:

PUSH TO ENTER

DIRECT → STEREO → SURROUND →

ALL CH STEREO → DIRECT...

(Refer to the “Selecting speakers” section on page 26 for more

details.)

Note:

3. Start playing the selected input source.

If you want to switch between Dolby Pro Logic II Movie and Dolby

Pro Logic II Music at the TX-DS595, press the jog dial and select

“SURROUND” for the listening mode.

Follow the operating instructions for the source device.

4. Selecting a listening mode.

Select a listening mode. (Refer to this page.)

When using the remote controller (for more details, see

page 9)

5. Adjust the volume to an appropriate level.

These controls allow you to adjust the volume of the Front,

Center, Surround speakers and subwoofer simultaneously.

Turning the control clockwise increases the volume level.

Turning the control counterclockwise decreases the volume.

(Refer to page 26 for more information.)

1. Press the RCVR MODE button.

2. Press one of the listening mode buttons, STEREO,

DIRECT, A. ST, SURR, DSP , or DSP , to select the

listening mode.

TX-DS595

Remote controller

MASTER VOLUME

VOL

• Use the bass and treble controls to adjust the tone.

(Refer to page 26 for more information.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Enjoying music or videos with the TX-DS595

SPEAKERS A/B

Jog dial

MASTER VOLUME

CH LEVEL

SLEEP

DISPLAY

RCVR

MODE

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

VOL

DISC

VOL

CH SEL

AUDIO

STANDBY

POWER

RETURN

AUDIO

MUTING

PUSH TO ENTER

OFF

ANGLE

SUBTITLE

DISPLAY

DIMMER

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

MUTING

LEVEL

TV/VCR

LEVEL

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

RANDOM

REC

OPEN/CLOSE

AV RECEIVER TX DS595

DVD

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

BASS TREBLE

SP A, B

Re-EQ

DISPLAY

DIMMER

ZONE

+10

-- ---

ENTER

DISPLAY

AUDIO SELECTOR

HOME THEATER CONTROLLER

RC-447M

Selecting speakers (SPEAKERS A, B)

Switching the display

SPEAKERS A: This button turns on or off the speakers connected

to the FRONT SPEAKERS, CENTER SPEAKER, SURROUND

SPEAKERS, and SUBWOOFER terminals.

When you listen to surround audio or select multi channel input, be

sure to turn on SPEAKERS A.

While listening to or watching an input source, you can display the

information regarding the type of source and signal being input by

pressing the DISPLAY button on the TX-DS595 or the remote

controller.

When an input source other than FM or AM is selected:

Input + volume

When the speakers are turned on, the SPEAKERS A indicator lights

up.

SPEAKERS B: This button turns on or off the speakers connected

to the FRONT SPEAKERS B terminals.

When the speakers are turned on, the SPEAKERS B indicator lights

up.

Program format*

Notes:

• You cannot select surround sound when you are using

SPEAKERS B.

Input +

Listening mode

or MULTI CH

• When using the B speakers, the A speakers can only be used for

stereo or direct playback, so nothing will be output from the left

and right surround speakers during multichannel playback.

* If the input signal does not have a program format, then this will

be skipped.

Adjusting the volume

When FM or AM is selected as the input source:

FM/AM frequency +

Preset no.

Adjusting the main volume adjusts the volume level output from all

the speakers connected to the TX-DS595 together. If headphones are

connected, this also adjusts the volume heard from the headphone

speakers. To adjust the volume, either press the VOL

buttons on

FM/AM +

Listening mode

the remote controller or turn the MASTER VOLUME dial. To

increase the volume, turn the dial clockwise; to decrease the volume,

turn the dial counterclockwise. The volume can be set to Min, 1 to

79, and Max.

Using the sleep time (Remote controller only)

Adjusting the bass and treble

The SLEEP button enables you to set the TX-DS595 to turn off

automatically after a specified time period. If you press it once, the

TX-DS595 will turn off after 90 minutes. Each time it is pressed

thereafter, the remaining time until the TX-DS595 turns off

decreases by 10 minutes. While, the sleep function is enabled, you

can press the SLEEP button to see how much time is left. To cancel

the sleep function, press the SLEEP button when the time displayed

is less than 10 minutes.

You can adjust the bass and treble levels using the BASS and

TREBLE dials. This function only affects the front left and right

speakers. For multichannel sources, these dials will not work if the

tone control is set to “OFF.” (Refer to page 27.)

Temporarily turning off the sound (Remote

controller only)

To turn off the sound momentarily, such as when interrupted by a

phone call, press the MUTING button on the remote controller.

When pressed, “MUTING” is displayed on the TX-DS595. Press the

MUTING button again to turn the sound back on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Enjoying music or videos with the TX-DS595

Changing the audio mode

Enjoying the multichannel input

Press the AUDIO SELECTOR button on the front panel (or the

AUDIO button on the remote controller) to change the audio mode.

Each time the button is pressed, the mode changes from “AUTO” →

“MULTICH” → “ANALOG” and back to “AUTO.” The “AUTO”

audio mode is recommended for normal circumstances.

Before starting operations, first make sure that the multichannel

connection is properly made and that the Multichannel setting of the

Input Setup → Audio Setup is set to “YES” (see page 29).

1. Press the input source button for the component with

multichannel output connected to the MULTI

AUTO (automatic detection): With this setting, the TX-DS595

automatically detects whether the input signal is digital or analog.

When a digital signal is not input, then the analog signal is played.

CHANNEL INPUT on the rear of the TX-DS595.

2. Select “MULTICH” using the AUDIO SELECTOR

button on the front panel (AUDIO button on the

remote controller).

MULTICH: Select this setting to play back the input from the

component connected to the MULTI CHANNEL INPUT port. This

setting is effective when the Multichannel setting in the Audio Setup

is set to “YES.”

TX-DS595

Remote controller

ANALOG: Select this setting to play back the input from a source

component connected to an analog audio input jacks. With this

setting, even if a digital signal is input from the same component,

only the analog signal will be output.

AUDIO

SELECTOR

3. Turn on the connected component and start playing

the desired media.

Temporarily changing the speaker output levels

4. If necessary, adjust the output level of each speaker

as desired (see “Temporarily changing the speaker

output levels” on this page).

To change the individual speaker volumes temporarily, follow the

procedure given below. Each channel can be set between –12 to +12

decibels. Note that the calibration settings will return to the original

settings when the TX-DS595 is put in standby.

Adjust the speaker output levels so that you can hear the same

sound level from each speaker at the listening position. For the

front right, front left, center, surround right, and surround left

speakers, the output levels can be adjusted between –12 to +12

decibels. The subwoofer can be adjusted between –30 to +12

decibels.

1. Press the CH LEVEL button and

CH LEVEL

select the desired speaker.

2. Turn the jog dial to adjust the

DSP/MODE ADJ

volume level.

5. Adjust the volume with the MASTER VOLUME dial or

the VOL

buttons on the remote controller.

PUSH TO ENTER

Using the tone control:

To make the BASS and TREBLE dials work for multichannel

sources, you must first set the tone control to “ON.”

When using the remote controller:

1. Press the RCVR MODE button.

1. Turn the tone control on by pressing either the jog

dial on the TX-DS595 or the DIRECT button on the

remote controller.

2. Press the CH SEL button and select

the desired speaker.

DSP/MODE ADJ

3. Press the LEVEL or button to

adjust the volume level.

DIRECT

PUSH TO ENTER

Notes:

When pressed only once, the current setting appears, so press

twice to change the setting.

• You cannot select a speaker if the CONFIG parameter of the

speaker is set to NO or NONE.

2. Adjust the tone using the BASS and TREBLE dials.

• If the speaker level is set to +1 dB or higher, the maximum level

indicated on the display will change if you raise the volume

level.

BASS

TREBLE

• When you press the TEST button after you set the level, the

current level will be used as the value set via the test tone.

Notes:

• Adjusting the volume level of each speaker for the MULTI CH

INPUT source does not affect the speaker level adjusted by the

listening position.

• If the speaker level is set to +1 dB or higher, the maximum level

indicated on the display will change if you raise the volume

level.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using listening mode

The TX-DS595’s surround sound enables you to enjoy the presence

of a movie theater or concert hall in your room.

• The outputs for the VIDEO 1 OUT and TAPE OUT output

analog audio signals. Do not record from CDs or LDs that

support DTS using these outputs. If you do, the DTS-encoded

signal will be recorded as noise.

The configuration of the speakers are very important for the

surround sound. Refer to “Connecting speakers” on page 15.

* The 5.1-channel digital surround format has a variety of versions

including Dolby Digital and DTS. The 5.1- channel digital

surround format enables you to individually record and play five

full-range (20 Hz to 20 kHz) channels (left and right front,

center, and two surround channels) plus an LFE channel (Low

Frequency Effect) for the low-range effect sound. It will create a

realistic sound that can be heard in the theaters and concert halls.

Before using a listening mode, make sure the Speaker Setup

parameters have been set (refer to page 19) . Once the parameters

have been set, it is not necessary to set them again. Refer to page 25

for information regarding how to select the listening mode.

• DOLBY PRO LOGIC II Surround

Listening modes

This mode is a new generation 5-channel surround system that

provides performance between the 4-channel (left front, right

front, center, and monaural surround) Pro Logic Surround and

the 5.1-channel Dolby Digital Surround. This mode can be set to

the Movie mode designed for playing movies and the Music

mode designed for listening to music. In the Movie mode, the

surround channels, which used to provide monaural output over

only a narrow frequency range, now provide complete stereo

output over the full frequency range. The result is movie viewing

with a realistic feel of movement. The Music mode uses the

surround channels to provide a natural sound space that cannot

be provided with normal stereo output.

Stereo

This mode has all input sounds output from the left and right front

speakers.

Direct

This mode delivers pure sound with minimum sound quality

adjustment and filtration. The sound recorded for the right and left

front channels is output to the right and left front speakers only and

not output to the subwoofer.

Surround modes

With this mode, decoding is performed automatically to match the

input signal. This original mode adds no sound processing to the

input signal.

This mode can be used with VHS and DVD videos with the

mark and certain television programs. The Music

mode can be used with music compact discs and other stereo

sources.

• Dolby D (Dolby Digital)

Digital data with AC-3 compression and a maximum of 5.1-

channel* surround sound. This source signal comes from DVDs

and LDs that have the

channel output. This source also comes from digital satellite

broadcasts that support Dolby Digital.

You can press the SURR button on the remote controller to

switch between MOVIE and MUSIC. The initial setting is

MOVIE. This setting can be made for each input source.

mark and therefore recorded for 5.1-

If no surround speakers are connected, then the surround sound

is divided and output from the front left and right channels (3

stereo).

• DTS

DTS (Digital Theater System) is compressed digital data with a

maximum 5.1-channel* surround output that allows for an

extremely high-quality sound. This source signal requires a

DVD player that supports DTS output and comes from compact

discs, DVDs, and LDs that have the mark.

Re-EQ function

You can use the Cinema Re-Equalization function when playing

back sources in the Dolby Digital and Dolby Pro Logic II Movie

modes (see page 9).

LATE NIGHT

Notes on DTS:

When using Dolby Digital, you can use the LATE NIGHT

function (see page 32).

• If you play a CD or LD that supports DTS when the

“ANALOG” setting is selected on the TX-DS595, the DTS

encoded signal will not be decoded and noise will be output.

This noise could damage the amplifier and speakers.

Therefore, be sure to selected “AUTO” and use the digital

input jacks (OPTICAL or COAXIAL) to connect the DTS

source.

Orchestra

This mode is appropriate for classical and opera music. The center

channel is cut and the surround channels are emphasized to widen

the stereo image. It will simulate the natural reverberation that is

created in large halls.

• The DTS indicator on the TX-DS595 lights while a DTS

source is played. When playback finishes and the DTS signal

transmission stops, the TX-DS595 remains in DTS mode and

the DTS indicator remains lit. This prevents noise when you

operate the pause or skip button on the player. Therefore, if

the source is immediately switched from DTS to PCM, the

PCM signal may not be played. In this case, stop the playback

of the source on the player for about three seconds and then

resume playback.

TV Logic

This mode gives realistic acoustics to TV programs that are aired

from TV studios. It enhances the entire surround sound and clarity of

the conversation.

Unplugged

This mode is suitable for acoustical instrumental sounds, vocals, and

jazz music. By emphasizing the front stereo image, it will simulate

the acoustics that you would experience in front of the stage.

• If you press the pause or skip button on the player while

playing a DTS source, on rare occasions a short noise may be

heard. This is not a malfunction.

Studio-Mix

This mode is for rock and popular music. The lively sounds are

enhanced for a powerful acoustic image that simulates the feeling of

being in a club or rock concert.

• You may not be able to play some DTS source signals from

certain CD players and LD players even if you connect the

player to the TX-DS595 digitally. This is because the digital

signal has been processed (such as the output level, sampling

frequency, or frequency response) and the TX-DS595 cannot

recognize the signal as DTS data. Therefore you may hear

noise when you play a DTS source while processing the

signal.

All Ch Stereo

This mode is designed for playing background music. The front,

surround, and surround back channels create a stereo image that

encompasses the entire area.

Download from Www.Somanuals.com. All Manuals Search And Download.

Input Setup

SETUP

2. Press the SETUP button.

2. Input Setup

These settings can be set differently for each input source.

Turn the jog dial or press the and cursor

buttons on the remote controller to display

“2. INPUT SETUP.”

DSP/MODE ADJ

Audio Setup

PUSH TO ENTER

DSP/MODE ADJ

Digital Input (D. INPUT): This setting tells the TX-DS595 which

input source button on the front panel is connected with which

digital input jack on the rear panel.

3. Press the jog dial or ENTER button

on the remote controller.

If you have connected your components in accordance with the

default settings (given in the table below), then there is no need to

change this setting.

“AUDIO SETUP?” appears in the front

display.

PUSH TO ENTER

DSP/MODE ADJ

Multichannel (MULTICH): This setting will not appear if AM or

FM is selected at the front panel for the input source. The initial

settings are “Yes” for the DVD input source and “No” for all other

input sources. This setting is normally set to “NO,” and only needs to

be changed to “YES” if a DVD player, MPEG decoder, or other

component that has a multi channel port is connected to the MULTI

CHANNEL INPUT port for 5.1-channel audio.

4. Press the jog dial or ENTER button

on the remote controller.

The name of the digital input currently

assigned to the selected input source

appears.

PUSH TO ENTER

DSP/MODE ADJ

5. Turn the jog dial or press the or

cursor button on the remote

Default setting

Input source

DVD

controller to select the digital input.

PUSH TO ENTER

Digital input

COAX 1

COAX 2

----

Multichannel

Yes

(Example: If connected to COAX 1.)

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

TAPE

OPT 2

----

DSP/MODE ADJ

6. Press either the jog dial or the

cursor button on the remote

controller.

----

PUSH TO ENTER

“MULTICH=YES” or “NO” appears.

PHONO

----

OPT 1

----: No setting

: Not applicable

DSP/MODE ADJ

If a component with a 5.1-channel output

terminal is connected (i.e., DVD player or

MPEG decoder), turn the jog dial or press

the and buttons on the remote controller

to select “YES.”

OPT1: Select if connected to DIGITAL INPUT (OPTICAL) 1.

OPT2: Select if connected to DIGITAL INPUT (OPTICAL) 2.

COAX1: Select if connected to DIGITAL INPUT (COAXIAL) 1.

COAX2: Select if connected to DIGITAL INPUT (COAXIAL) 2.

----: Select if the input source is not from a digital input jack.

PUSH TO ENTER

RETURN

7. Press the RETURN button.

“AUDIO SETUP?” appears in the front

Notes:

display.

• Do not assign a digital input to more than one input source. If

you are making a digital connection that requires you to change

the default settings, be sure to always first cancel the current

digital input setting and then assign the new setting.

SETUP

To exit the setup mode immediately, press

the SETUP button.

• When playing a device that is actually connected to the MULTI

CHANNEL INPUT terminal, select MULTICH with the

AUDIO SELECTOR button (see page 27).

Listening Mode Preset

With the TX-DS595, you can set a different listening mode for each

different signal type that comes from each input source.

Audio Setup procedure

For example, with the default settings, even when using the same

DVD player, if a CD is played, the listening mode automatically

becomes “STEREO,” and if a DVD is played (Dolby Digital 3/2.1),

the listening mode automatically becomes Dolby D.

1. Select the desired input source.

TX-DS595

DVD

VIDEO 1 VIDEO 2 VIDEO 3

TAPE

PHONO

Analog/PCM Source: Set a listening mode for the input signal from

2-channel analog sources and PCM source (default: STEREO.)

VCR

Note:

For PCM sources recorded at a sampling rate of 96 kHz or greater,

only the Stereo or Direct listening modes can be selected. However,

the set listening mode is stored in memory.

Remote controller

Digital format Source: Set a listening mode for the input signal

from digital sources (default: SURROUND).

Download from Www.Somanuals.com. All Manuals Search And Download.

Input Setup

DSP/MODE ADJ

1. Select the desired input source.

5. Turn the jog dial or press the or

cursor buttons on the remote

controller to select the listening

mode.

PUSH TO ENTER

TX-DS595

DVD

VIDEO 1 VIDEO 2 VIDEO 3

VCR

TAPE

PHONO

Refer to the table to see what listening

modes are available.

DSP/MODE ADJ

6. Press either the jog dial or the

cursor button on the remote

controller.

Remote controller

PUSH TO ENTER

The listening mode when playing a digital

format source with the currently selected

input source appears.

SETUP

2. Press the SETUP button.

Turn the jog dial or press the and cursor

buttons on the remote controller to display

“2. INPUT SETUP.”

DSP/MODE ADJ

7. Turn the jog dial or press the or

cursor button on the remote

controller to select the listening

mode.

PUSH TO ENTER

DSP/MODE ADJ

PUSH TO ENTER

3. Press the jog dial or ENTER button

on the remote controller.

Refer to the table to see what listening modes are available.

RETURN

PUSH TO ENTER

DSP/MODE ADJ

8. Press the RETURN button.

“LSTNMODEPRESET?” appears in the

Turn the jog dial or press the cursor button

on the remote controller to display

“LSTNMODEPRESET?”.

front display.

SETUP

PUSH TO ENTER

DSP/MODE ADJ

To exit the setup mode immediately, press

the SETUP button.

4. Press the jog dial or ENTER button

on the remote controller.

The listening mode when playing an analog/

PCM source with the currently selected

input source appears.

PUSH TO ENTER

Relationship between input source and listening mode

Input source signal (display)

Analog/PCM Source

Tape, CD,

Digital Format

DVD,

Type of media

Record, Tuner

Digital satellite broadcast,

DTS-CD

DVD Video (PCM), LD (PCM)

Digital satellite broadcast

Dolby Digital 2ch Source

DTS,

All excluding

Dolby Digital 2ch

Listening Mode

Direct

Stereo

Surround

Pro Logic II (Movie)

Pro Logic II (Music)

Dolby Digital

DTS

Orchestra

Unplugged

Studio-Mix

TV Logic

All Ch Stereo

Notes:

• The listening modes that can be set are different for each input source format.

• You may not be able to select all the listening modes shown here depending on your speaker

configuration or the selected input source.

Download from Www.Somanuals.com. All Manuals Search And Download.

Input Setup

IntelliVolume

When switching input sources, you may find that the output level for

different components or input sources connected to the TX-DS595 is

different even though the main volume setting is the same. Under

normal circumstances, you would then have to change the volume

setting each time you change the input source. This IntelliVolume

allows you to preset a volume level for each input source separately

so that when you do switch from one input source to another, the TX-

DS595 adjusts the volume accordingly so that the resulting volume

stays the same.

1. Select the desired input source.

TX-DS595

DVD

VIDEO 1 VIDEO 2 VIDEO 3

TAPE

PHONO

VCR

Remote controller

SETUP

2. Press the SETUP button.

DSP/MODE ADJ

Turn the jog dial or press the and cursor

buttons on the remote controller to display

“2. INPUT SETUP.”

PUSH TO ENTER

DSP/MODE ADJ

3. Press the jog dial or ENTER button

on the remote controller.

PUSH TO ENTER

DSP/MODE ADJ

Turn the jog dial or press the cursor button

on the remote controller to display

“INTELLIVOLUME?”.

PUSH TO ENTER

DSP/MODE ADJ

4. Press the jog dial or ENTER button

on the remote controller.

The currently set volume level appears.

PUSH TO ENTER

DSP/MODE ADJ

5. Turn the jog dial or press the and

cursor buttons on the remote

controller to set the IntelliVoleme.

PUSH TO ENTER

It can be adjusted between -12 and +12

decibels.

RETURN

6. Press the RETURN button.

“INTELLIVOLUME?” appears in the front

display.

SETUP

To exit the setup mode immediately, press

the SETUP button.

Download from Www.Somanuals.com. All Manuals Search And Download.

Preference

5. Press the RETURN button.

3. Preference

“HEADPHONES LVL?” appears in the front display.

Volume Setup

To exit the setup mode immediately, press the SETUP button.

Maximum Volume (MAXIMUM VOL): This setting allows you to set

the maximum volume that can be output with the MASTER VOLUME

dial to prevent components from being damaged by excessively loud

volumes. When Maximum Volume is not set, set this to OFF.

AM Frequency step Setup

This screen only appears on the worldwide model. The initial setting is 9

kHz, and this needs only to be changed if you are using the TX-DS595 in

a 10-kHz region.

Power On Volume (POWERONVOL): This sets a designated volume

setting for the TX-DS595 to be set every time that the power is turned on.

This prevents the TX-DS595 from being turned on while it is set to an

extremely high volume and suddenly output very loud sounds.

1. Press the SETUP button.

Turn the jog dial or press the and cursor buttons on the remote

controller to display “3. PREFERENCE.”

1. Press the SETUP button.

Turn the jog dial or press the and cursor buttons on the remote

controller to display “3. PREFERENCE.”

2. Press the jog dial or ENTER button on the remote

controller.

2. Press the jog dial or ENTER button on the remote

controller.

Turn the jog dial or press the

controller to display “AM FREQ STEP?”.

cursor button on the remote

“VOLUME SETUP?” appears in the front display.

3. Press the jog dial or ENTER button on the remote

controller.

3. Press the jog dial or ENTER button on the remote

controller.

The currently set frequency step appears.

“MAXIMUM VOL=” appears in the front display.

4. Turn the jog dial or press the or cursor buttons on

the remote controller to set the frequency.

4. Turn the jog dial or press the or cursor button on

the remote controller to set the maximum volume.

5. Press the RETURN button.

The maximum volume can be set between 30 and 79.

“AM FREQ STEP?” appears in the front display.

To exit the setup mode immediately, press the SETUP button.

5. Press either the jog dial or the cursor button on the

remote controller.

“POWER ON VOL” appears in the front display.

Late Night Setup

6. Turn the jog dial or press the or cursor button on

the remote controller to set the power on volume.

Sets “HIGH,” “LOW,” or “OFF” for the late night function.

Cinema sound has a vast dynamic range; therefore, to hear the quieter

sounds such as human conversations, they must be played back at larger

volumes. When this parameter is set to “HIGH” or “LOW,” the dynamic

range of the sound is narrowed down to allow you to easily hear minute

sounds at low volumes. This function is especially useful if you wish to

play a movie at low volumes during the nighttime.

The power on volume can be set between “MIN” and the value set

for “MAXIMUM VOL.” If you do not mind having the TX-DS595

turned on with its current volume setting, set this to “LAST.”

7. Press the RETURN button.

“VOLUME SETUP?” appears in the front display.

To exit the setup mode immediately, press the SETUP button.

1. Press the SETUP button.

Turn the jog dial or press the and cursor buttons on the remote

controller to display “3. PREFERENCE.”

Headphones Level

2. Press the jog dial or ENTER button on the remote

controller.

You can use this setting to adjust the volume output from the headphones

so that it matches the level output from the speakers.

Turn the jog dial or press the

controller to display “LATE NIGHT?”.

cursor button on the remote

1. Press the SETUP button.

Turn the jog dial or press the and cursor buttons on the remote

controller to display “3. PREFERENCE.”

3. Press the jog dial or ENTER button on the remote

controller.

2. Press the jog dial or ENTER button on the remote

controller.

The current setting appears.

4. Turn the jog dial or press the or cursor buttons on

the remote controller to set the late night function.

Turn the jog dial or press the

controller to display “HEADPHONES LVL?”.

cursor button on the remote

3. Press the jog dial or ENTER button on the remote

controller.

5. Press the RETURN button.

“LATE NIGHT?” appears in the front display.

To exit the setup mode immediately, press the SETUP button.

Notes:

“HP LEVEL” appears in the front display.

4. Turn the jog dial or press the or cursor button on

the remote controller to set the headphone volume.

•

The depth of the Late Night effect is determined by Dolby Digital

software. Some sounds may produce no or little effect.

The Late Night function is effective only on Dolby Digital encoded

software.

The headphone volume can be adjusted between –12 and +12

decibels.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Recording

SPEAKERS

CH LEVEL

MASTER VOLUME

STANDBY/ON

SETUP

DSP/MODE ADJ

STANDBY

POWER

RETURN

PUSH TO ENTER

OFF

DISPLAY

RT/PTY/TP

FM MODE PRESET MEMORY

TUNING

PRESET

SMART SCAN NAVIGATOR

BASS

TREBLE

PHONES

AUDIO

SELECTOR

DVD

VIDEO

VCR

VIDEO

TAPE

PHONO

AV RECEIVER TX DS595

Input source buttons

The TX-DS595 can also be used to record an input source media.

This allows you to make copies of the music or videos you like, copy

them from one type of media to another, or even record what is being

broadcast on television or radio.

Tip:

If you want to record the video from one source and the audio from

another source together, such as recording the video from a video

camera connected to VIDEO 2 and the audio from a CD player

connected to CD, in step 2 above, select the source for the video and

then select the source for the audio. The remaining procedure is the

same as that above.

Recording an audio source

Notes:

Make all connections between the tape deck and the receiver as

• If you change the input source during recording, you will record

the signals from the newly selected input source.

shown in the “Connections” diagram (pages 11-13).

• You cannot record the surround effects.

1. Insert a blank tape into the tape deck.

• You cannot perform digital recording with the TX-DS595. Also,

digital-to-analog signal conversion is not possible, so to record

audio signals from digital sources (e.g. CD players), you must

not only make the digital connection, but the analog connection

as well.

2. Press the input source button for the source you

want to record.

• If you select DVD, VIDEO 1, VIDEO 2, or VIDEO 3, only the

audio will be recorded.

• You cannot record the source connected to the MULTI

• If you select FM or AM, set the tuner to the station you want to

CHANNEL INPUT connector.

record.

DVD

VIDEO 1 VIDEO 2 VIDEO 3

VCR

TAPE

PHONO

3. Set the tape deck in recording mode. Start playing

the source.

Set the proper recording level using the controls on the tape

deck.

Recording data from a video disc player (or a

video camcorder) to VCR

Video disc programs can be recorded onto a VCR (VIDEO 1).

1. Load a disc in the video disc player or DVD player,

and insert a blank tape in the VCR (VIDEO 1).

2. Press the VIDEO 2, VIDEO 3, or DVD button.

3. Start playing the source and recording on the VCR.

Refer to the video equipment connections section on the page 12.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using remote controller

Overview

The RC-447M remote controller is a useful tool to help you operate

the components of your home theater. To do so, first press the Mode

button that corresponds to the device you wish to control. Then

simply press the desired operation button and the component will

operate accordingly. For example, if you wish to select the CD input

source at the TX-DS595 with the remote controller, first press the

RCVR MODE button to select the TX-DS595 and then press the CD

(INPUT SELECTOR) button.

Calling up a preset radio station

1. Press the RCVR MODE button.

The RCVR MODE button lights green.

RCVR MODE

2. Press the TUN input selector button.

3. Press the CH or button to select the desired

preset station number.

DISC

VOL

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

RANDOM

REC

OPEN/CLOSE

DVD

T 1

TUN

STEREO

DIRECT

DSP

Controlling an Onkyo cassette tape deck

The z connector of the Onkyo cassette tape deck must be

connected to the TX-DS595 (see page 13).

1. Press the RCVR MODE button.

The RCVR MODE button lights green.

RCVR MODE

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control an Onkyo cassette tape deck.

DISC

VOL

Operation buttons:

: Play

AUDIO

MUTING

: Stop

ANGLE

SUBTITLE

TV/VCR

LEVEL

: Rewind

TAPE

operation

buttons

: Fast forward

RANDOM

REC

OPEN/CLOSE

: Press during playback to skip to the beginning of the next track.

: Press during playback to skip to the beginning of the current

track.

DVD

T 1

REC: Record/Pause

TUN

STEREO

DIRECT

DSP

: Reverse playback

SURR

A.ST

DSP

SPA

SP B

Re-EQ

You may also use the following buttons:

DISPLAY

DIMMER

ZONE

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Note:

Even for devices with the

and

buttons, signal discrepancies

may cause them not to work properly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using remote controller

Controlling an Onkyo CD player

The z connector of the Onkyo compact disc player must be

connected to the TX-DS595 (see page 13).

1. Press the CD MODE button.

STDBY

The CD MODE button lights green.

2. Press the desired operation button.

CD MODE

The buttons shaded in the figure to the left are the operation

buttons that can be used to control an Onkyo compact disc

player.

DISC

Operation buttons:

DISC

VOL

ON: Turns on and off the compact disc player (same as STDBY

button on the remote controller).

AUDIO

MUTING

DISC : Selects a disc in the CD changer

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

: Track down

operation

buttons

: Track up

RANDOM

REC

OPEN/CLOSE

: Play

: Stop

DVD

: Fast reverse

T 1

TUN

: Fast forward

STEREO

DIRECT

DSP

: Pause

SURR

A.ST

DSP

Numeric keys

OPEN/CLOSE r: Open/close the disc tray

0, 1 to 9, +10: Numeric keys

RANDOM: For random playback.

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

You may also use the following buttons:

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

Download from Www.Somanuals.com. All Manuals Search And Download.

Using remote controller

Controlling an Onkyo DVD player

The z connector of the Onkyo DVD player must be connected to

the TX-DS595 (see page 13).

1. Press the DVD MODE button.

The DVD MODE button lights green.

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control an Onkyo DVD player.

Operation buttons:

ON: Turns the DVD player on and off.

STDBY: Turns the DVD player off. (Some sets may not respond to

this button. In this case, use the ON button to put the DVD player in

the standby state.)

STDBY

SETUP: Displays the menu.

: Moves the cursor.

RETURN

DVD MODE

SETUP

VOL

ENTER: Confirms the selection.

RETURN: Return button

ENTER/Cursor

button

TOP MENU or MENU: Displays the menu screen(s) recorded on

DVD media.

DISC

VOL

DISC

: Selects a disc in the DVD changer.

TOP MENU

AUDIO

MUTING

AUDIO

MUTING

ANGLE

SUBTITLE

AUDIO: Press repeatedly to select an audio and/or language track

recorded on a DVD-Audio/Video.

TV/VCR

LEVEL

SUBTITLE

ANGLE

ANGLE: Press repeatedly to select a camera angle when a DVD-

Video is recorded with multiple angle playback.

RANDOM

REC

OPEN/CLOSE

DVD

operation

buttons

SUBTITLE: Press repeatedly to select one of the subtitle languages

recorded on a DVD-Video.

DVD

T 1

SEARCH: Press to find the specific section on a disc where you

TUN

want to start playback.

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Numeric keys

RANDOM: Press to start random playback.

SPA

SP B

Re-EQ

: Chapter/Track down

DISPLAY

DIMMER

ZONE

-- ---

ENTER

: Chapter/Track up

: Play

HOME THEATER CONTROLLER

RC 447M

: Stop

: Fast reverse

: Fast forward

: Pause

OPEN/CLOSE r: Open/close the disc tray

0, 1 to 9, +10: Numeric keys

You may also use the following buttons:

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

Note:

When operating an Onkyo DVD player directly with the remote

controller without connecting the z terminals, pre-programming is

necessary (see page 38).

Download from Www.Somanuals.com. All Manuals Search And Download.

Using remote controller

Controlling an Onkyo MD recorder

The z connector of the ONKYO MD recorder must be connected

to the TX-DS595 (see page 13).

1. Press the MD MODE button.

The MD MODE button lights green.

STDBY

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control an Onkyo MD recorder.

MD MODE

Operation buttons:

ON: Turns on and off the MD player (same as STDBY button on the

remote controller).

DISC

VOL

: Track down

: Track up

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

: Play

: Stop

operation

buttons

RANDOM

REC

OPEN/CLOSE

: Fast reverse

: Fast forward

REC: Record

: Pause

DVD

T 1

TUN

STEREO

DIRECT

DSP

r: Eject the disc

1 to 9, 0, --/---: Numeric keys

ENTER: Enters the settings

Numeric keys

ENTER

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

You may also use the following buttons:

HOME THEATER CONTROLLER

RC 447M

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

SAT, CABLE, VCR, and TV MODE buttons

No preset codes are programmed into the SAT, CABLE, VCR, and

TV MODE buttons. You can use these buttons to program the

remote controller signals of other devices.

There are two methods. One method is selecting the name of a

different brand from the table, entering the setting number listed, and

calling up the pre-programming code (see page 38). The other

method is learning the commands from the other brand’s remote

control directly into this remote controller (see page 42).

CABLE

SAT

VCR

When in the SAT, CABLE and VCR mode, you may use the

following buttons:

DISC

VOL

VOL : Adjusts the volume at the TX-DS595

AUDIO

MUTING

ANGLE

SUBTITLE

MUTING

MUTING: Activates the muting function at the TX-DS595

TV/VCR

LEVEL

Download from Www.Somanuals.com. All Manuals Search And Download.

Learning a pre-programming code

The remote controller has three learning functions. One is entering

Learning a pre-programming code

the signal number for a remote controller of another brand that is pre-

programmed. Another is a normal learning function that enables the

remote controller to learn the codes from other remote controllers.

And the last is a macro learning function that enables you to program

a series of operations into the remote controller so that the operations

can all be performed at once by pressing one button.

By learning a pre-programming code, you can make the RC-447M

remote controller able to operate a product from another brand. The

buttons that are used for operation are given on the next page.

1. Find the 3-digit number for the brand name of the

component that you want to operate in the table on

the next page.

2. Turn on the component that you want to operate (i.e.

DVD, satellite tuner, or television).

SEND/LEARN

indicator

3. While holding down the MODE button on the RC-

447M that you want to program, press the DISPLAY

button, and then release both buttons.

The SEND/LEARN indicator lights when the MODE button is

pressed and turns off when the DISPLAY button is pressed. Wait

until the indicator turns off before releasing both buttons. Then

the SEND/LEARN indicator lights again.

Buttons that

can be pre-

programmed

DISC

4. Within 30 seconds, enter the 3-digit code number.

VOL

The SEND/LEARN indicator flashes twice slowly. If the SEND/

LEARN indicator quickly flashes three times, then either a

mistaken 3-digit code was entered or an incorrect operation was

performed. If this occurs, return to step 3.

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

RANDOM

REC

OPEN/CLOSE

5. Press the button that you programmed and check if

the system operates correctly.

DVD

• If the component does not operate properly, return to step 3

and repeat the steps above.

T 1

TUN

• If it still does not operate properly, then program the

commands one by one to the buttons on the RC-447M remote

controller.

STEREO

DIRECT

DSP

Numeric keys

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

When entering the code of Onkyo DVD players:

There are three SETTING numbers. Choose the SETTING number

according to how you will be using the DVD player.

ENTER

-- ---

DISPLAY

HOME THEATER CONTROLLER

RC 447M

No. 601/613: These codes are for operating the Onkyo DVD player

by pointing the remote controller directly at it, either because it does

not have an z terminal, or it does but you are not using an z cable

and connecting it. First enter 601 and if it does not operate properly,

enter 613.

Caution

With some brand’s components, some buttons may not work

correctly. In this case, program the command separately.

No. 600: This code is for Onkyo DVD players that have an z

terminal that you are connecting to the TX-DS595 with an z cable.

You will then operate the DVD player by pointing the remote

controller at the remote control sensor on the TX-DS595. You do not

need to enter this code because it is factory preset. However, if the

code has been changed to 601 or 613, then you will need to change it

back to 600.

Download from Www.Somanuals.com. All Manuals Search And Download.

Learning a pre-programming code

Pre-programmong codes

VCR

BRAND

SETTING No.

300, 301, 302

303, 304, 305, 306,

307

308

309

310

311, 312, 313

314

315, 316

317

318, 319, 320, 321,

322

323

BRAND

SETTING No.

100, 101

102, 103, 104

105

106

107

108, 109

110

111, 112, 113

114

115, 116

117, 118, 119, 120,

121

AIWA

AKAI

AIWA

AKAI

Note:

If more than one code is given in the table,

try the code one by one until you reach the

code for your component (i.e. if the first

code does not work, then try the next).

AUDIOSONIC

BELL & HOWELL

BLAUPUNKT

BRIONVEGA

CENTURION

COLTINA

CORONAD

CROWN

DAEWOO

BAIRD

BELL & HOWELL

BLAUPUNKT

CGM

COLTINA

DAEWOO

DIGITAL

DVD

BRAND

SETTING No.

602, 609

603

DENON

HITACHI

JVC

EMERSON

604

KENWOOD

MAGNAVOX

MARANTZ

MITSUBISHI

ONKYO

PANASONIC

PIONEER

PROSCAN

RCA

605

606, 613

607

608, 613

600, 601, 613

609

610

611

FENNER

FISHER

DUAL

EMERSON

122

324, 325, 326, 327

123, 124, 125, 126,

127

128, 129

130, 131

132

FUJITSU GENERAL 328

FUNAI

GO VIDEO

GOLDSTAR

GOODMANS

GRUNDIG

HITACHI

JVC

FENNER

FERGUSON

FISHER

329

330, 331

332, 336, 337

333, 334

335

FUNAI

133, 134, 135

FUJITSU GENERAL 136, 137, 138

139, 140, 141

142, 143

144

145, 146

147, 148, 149, 150

151

SONY

612

338

GOLDSTAR

GOODMANS

GRUNDIG

HITACHI

HYPER

TOSHIBA

YAMAHA

ZENITH

613

609, 614

613, 615

339, 340, 341

342, 343, 344, 345,

346, 347, 348, 349,

350

LOEWE

MAGNAVOX

MITSUBISHI

351, 352

INNO HIT

IRRADIO

JVC

152

103

353, 354, 355

356, 357, 358, 359,

360, 361, 362, 363,

364

SAT

BRAND

153, 154, 155, 156,

157

158

SETTING No.

ECHOSTAR

GENERAL

INSTRUMENTS

HITACHI

HUGHES

NETWORK

SYSTEMS

PANASONIC

PRIMESTAR

PROSCAN

RCA

700

KENDO

NEC

NOKIA

NORDMENDE

OKANO

ORION

365, 366, 367

313

368, 369, 370

371, 372

319, 373

374, 375, 376, 377,

378

353, 379, 380

311

381

382

383

KTV

LUXOR

159, 160

161

162, 163

164

701

702

MAGNAVOX

MARANTZ

MARK

MATSUI

MITSUBISHI

MIVAR

NEC

NOKIA

OCEANIC

NORDMENDE

OKANO

ORION

PANASONIC

PHILIPS

PIONEER

PROSCAN

QUASAR

RADIO SHACK

RCA

165

703

704

705

706, 707

708

PANASONIC

166, 167, 168, 169

170, 171, 172, 173

174, 175

176, 177

178, 179, 180, 181

181

PHILIPS

PHONOLA

PIONEER

RCA

SABA

SAMSUNG

SONY

TOSHIBA

709

182, 183

152

384, 385, 386, 387,

388, 389, 390

391, 392, 393

394

184, 185, 186

187, 188, 189, 190

152, 162, 191

192, 193

194

SANYO

SCOTT

SELECO

SHARP

SHINTOM

SIEMENS

SONY

CABLE

BRAND

GENERAL

INSTRUMENTS

GEMINI

SETTING No.

395

396, 397, 398, 399

400

401

402, 403, 404, 405,

406, 407, 408, 409,

410, 411, 412, 413

414

414, 415

416, 417

418, 419, 420

500

501

195

196

HAMLIN

JERROLD

502, 503, 504, 505

500, 506, 507, 508,

509, 510, 511, 512,

513, 514

515, 516, 517

518

519, 520, 521

522, 523

524, 525, 526, 527,

528, 529

110, 141, 197, 198,

199, 200

182, 183, 201

202, 203, 204, 205,

206, 207, 208

209, 210, 211, 212

103

SABA

SAMSUNG

SYMPHONIC

TEKNIKA

TELEFUNKEN

TOSHIBA

WHITE

WESTINGHOUSE

WATSON

MACOM

MAGNAVOX

OAK

PANASONIC

PHILIPS

SANYO

SCHNEIDER

SEARS

SELECO

SHARP

213

333

421

422

214, 215

216, 217

218, 219, 220, 221,

222, 223

224, 225

201, 226, 227

228

213, 229

230

231, 232

PIONEER

SCIENTIFIC

ATLANTA

SAMSUNG

TOCOM

530, 531

ZENITH

SONY

532, 533, 534

535

536

SYMPHONIC

TELEFUNKEN

THOMSON

TOSHIBA

UNIVERSUM

ZENITH

537, 538

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating your programmed remote controller

After performing the procedure given above, the following

modes become enabled for use.

DVD MODE (DVD Player Mode)

Buttons with programmed usage and operations are the same as the

operational buttons on page 36.

SAT MODE (Satellite Tuner Mode)

1. Press the SAT MODE button.

The SAT button lights green.

STDBY

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control your satellite tuner unit.

SAT MODE

The buttons given below have operations programmed

into them.

ON: Turns on and off the satellite tuner unit (same as STDBY button

on the remote controller)

ENTER/Cursor

button

DISC

VOL

: Moves up and down the preset channel numbers

AUDIO

MUTING

: Moves the cursor

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

ENTER: Confirms the selection

MENU: Displays the menu

0,1 to 9: Numeric keys

RANDOM

REC

OPEN/CLOSE

ENTER: Confirm

DVD

You may also use the following buttons:

T 1

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

TUN

STEREO

DIRECT

DSP

Numeric keys

ENTER

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

-- ---

ENTER

HOME THEATER CONTROLLER

RC 447M

CABLE MODE (Cable Mode)

1. Press the CABLE MODE button.

The CABLE button lights green.

STDBY

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control your cable TV unit.

CABLE MODE

The buttons given below have operations programmed

into them.

ON: Turns on and off the cable TV unit (same as STDBY button on

the remote controller)

DISC

VOL

: Moves up and down the preset channel numbers

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

0,1 to 9: Numeric keys

LEVEL

ENTER: Confirm

RANDOM

REC

OPEN/CLOSE

You may also use the following buttons:

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

DVD

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Numeric keys

ENTER

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating your programmed remote controller

VCR MODE (VCR Mode)

1. Press the VCR MODE button.

The VCR button lights green.

STDBY

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control your VCR.

VCR MODE

The buttons given below have operations programmed

into them.

ON: Turns on and off the VCR (same as STDBY button on the

remote controller)

DISC

VOL

: Moves up and down the preset channel numbers

AUDIO

MUTING

TV/VCR: Switches the AV input for the VCR

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

: Play

: Stop

Video cassette

recorder

operation

buttons

RANDOM

REC

OPEN/CLOSE

: Rewind

: Fast Forward

: Pause

DVD

T 1

TUN

0,1 to 9, +10: Numeric keys

STEREO

DIRECT

DSP

You may also use the following buttons:

SURR

A.ST

DSP

Numeric keys

SPA

SP B

Re-EQ

VOL : Adjusts the volume at the TX-DS595

MUTING: Activates the muting function at the TX-DS595

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

TV MODE (TV Mode)

1. Press the TV MODE button.

The TV button lights green.

STDBY

2. Press the desired operation button.

The buttons shaded in the figure to the left are the operation

buttons that can be used to control your television.

The buttons given below have operations programmed

into them.

DVD MODE

ON: Turns on and off the television (same as STDBY button on the

remote controller)

DISC

VOL

: Moves up and down the television channels

AUDIO

MUTING

TV/VCR: Switches the TV/VCR input for the television

0,1 to 9, +10: Numeric keys

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

ENTER: Confirm

RANDOM

REC

OPEN/CLOSE

VOL : Adjusts the volume at the television

MUTING: Activates the muting function at the television

DVD

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

Numeric keys

ENTER

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the commands of remote controllers

for other devices into the remote controller

Programming procedure

When programming the commands of another remote controller to

the RC-447M remote controller, you must first decide under which

MODE button you want the commands to be linked. In general, you

will select the MODE button that corresponds to the component you

are programming. For example, if you are programming the

functions from a remote controller for a compact disc player, you

would choose the CD MODE button. Then, by pressing the CD

MODE button, the buttons on the RC-447M remote controller will

change to the commands you program here to operate the compact

disc player.

L U

I N

E R

I - C

T U

I N

E R

S U

- 2

I S

E L

T U

I D

I M

I N

- 1

T A

I D

E E

P O

After programming which MODE button to use, you will then

transfer the separate commands from the other remote controller

over to the RC-447M remote controller one at a time. Each

command is then programmed to a different button on the RC-447M

remote controller. Any button is programmable for this step except

for the eight MODE buttons (RCVR, CD, DVD, MD, SAT, CABLE,

VCR, and TV) and the two MACRO buttons (DIRECT and MODE).

Even after the commands have been memorized, keep your old

remote controller in a safe place. If for some reason the commands

are lost (e.g., when the batteries run down), it will be necessary to

memorize them once again.

5 to 15 cm

(2 to 6 inches)

1. Place the remote controller and the remote controller

for the other device facing each other at a distance of

5 to 15 cm (2 to 6 inches) apart.

2. While pressing and holding down the desired MODE

button on the remote controller, press the ENTER

button and then release both buttons.

SEND/LEARN

indicator

When you press and hold down the MODE button, the SEND/

LEARN indicator lights. When you press the ENTER button, the

lamp turns off. When you release the buttons, the lamp lights

again.

3. Press and release the button on the remote controller

to which you want to transfer the next command.

You may select any button but the ten ones indicated in the

figure below. When you press the button, the SEND/LEARN

indicator turns off. When you release the button, the indicator

lights again.

If you press the wrong button by mistake, press that same button

again. The SEND/LEARN indicator flashes twice, and the

remote controller exits the programming mode.

MODE

buttons

DISC

VOL

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

RANDOM

REC

OPEN/CLOSE

DVD

T 1

TUN

STEREO

DIRECT

DSP

DIRECT MACRO

MODE MACRO

MODE buttons

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

ENTER

HOME THEATER CONTROLLER

RC 447M

Buttons that cannot be programmed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the commands of remote controllers for other devices into the

remote controller

Notes:

4. Press and hold down the button (that corresponds to

• The remote controller codes for Onkyo compact disc players,

cassette tape decks, DVD players, and mini disc recorder have

already been programmed into buttons on the remote controller.

You may, however, use these buttons to program the codes for

other remote controllers. If you wish to restore the Onkyo preset

codes after you program new codes, you must first erase the new

codes (see page 44).

the command you are programming) on the remote

controller of the other device until the SEND/LEARN

lamp on the remote controller flashes twice.

After flashing twice, the SEND/LEARN indicator will light

again.

5. Repeat Steps 3 and 4 to transfer all the commands

you desire from the other remote controller and

program them to buttons on the remote controller

under the same MODE.

• The remote controller has 408 memory slots (8 modes × 51

buttons). Some remote controllers may have more commands

that can be remembered by the remote controller. In such cases,

it will be necessary for you to determine which commands are

more important than others.

Repeat Steps 2 through 4 to program commands to a different

MODE (e.g., when programming from a different remote

controller).

• If no button is pressed for more than 30 seconds during the

programming, or if you perform an invalid operation during

programming, the SEND/LEARN indicator flashes three times

quickly, and the remote controller exits the programming mode.

Resume from Step 2.

6. Press the MODE button that you pressed in step 2 to

complete the programming.

• If a failure occurs during programming, the SEND/LEARN

indicator flashes three times quickly, and the remote controller

exits the programming mode. Resume from Step 3.

7. Operate the newly programmed buttons to make sure

the learning function was performed properly.

• If a failure occurs five times in row during programming, the

remote controller exits the programming mode. Resume from

Step 3.

• If you try to program beyond the learning capacity of the remote

controller, the SEND/LEARN indicator flashes six times

quickly, and the remote controller exits the programming mode.

Try programming under a different MODE button.

• When you want to program a command to a button to which you

have already programmed a command, simply follow the same

procedure given and programming for that button will be

overwritten.

• The remote controller uses infrared rays to send its commands,

as do most other remote controllers. Though most remote

controller codes can be memorized by the remote controller, be

aware that some remote controllers use a system that is quite

different from the remote controller and therefore may not be

able to be programmed.

• Some remote controllers have a single button that performs

multiple functions (for example, the function may change each

time the button is pressed). If this is the case, each function must

be programmed to a separate button on the remote controller.

• Once you have transferred the commands from the other remote

controller, refer to the instruction manual that came with that

product for instructions on how to operate that product.

• Make sure both the remote controller and the other remote

controller have new batteries. If either of them has batteries that

are low, you may not be able to program the commands of the

other remote controller properly into the remote controller.

See page 48 for how to erase the memorized commands from all

buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming the commands of remote controllers for other devices into the

remote controller

Erasing the programmed command from one

button

SEND/LEARN

indicator

You can only erase memorized commands and not preset ones.

1. Press and hold down the desired MODE button for

the command, press the ENTER button, and then

release both buttons.

MODE

buttons

When you press the MODE button, the SEND/LEARN indicator

lights. When you press the ENTER button, the lamp turns off.

When you release the buttons, the lamp lights again.

DISC

VOL

2. Press and release the button for the command you

wish to erase.

AUDIO

MUTING

When you press the button, the SEND/LEARN indicator turns

off. When you release the button, the lamp lights again.

ANGLE

SUBTITLE

TV/VCR

LEVEL

3. Press and release the same button again.

RANDOM

REC

OPEN/CLOSE

The SEND/LEARN lamp flashes twice slowly. The memorized

command is erased.

DVD

T 1

Note:

TUN

If no button is pressed for more than 30 seconds during the erasing

procedure, the SEND/LEARN indicator flashes three times quickly,

and the remote controller exits the erasing mode. Resume from Step

STEREO

DIRECT

DSP

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

ENTER

HOME THEATER CONTROLLER

RC 447M

Erasing all the commands programmed under a

MODE button

SEND/LEARN

indicator

1. Press and hold down the desired MODE button,

press the ENTER button twice, and then release both

buttons.

When you press the MODE button, the SEND/LEARN indicator

lights. When you press the ENTER button, the lamp turns off.

When you release the buttons, the lamp flashes twice slowly and

then lights again.

MODE

buttons

2. Press and release the same MODE button again.

DISC

VOL

When you release the button, the SEND/LEARN indicator

flashes twice slowly. This erases all the commands memorized

to the MODE button.

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

Notes:

• If no button is pressed for more than 30 seconds during the

erasing procedure, the SEND/LEARN indicator flashes three

times quickly and the remote controller exits the erasing mode.

Resume from Step 1.

RANDOM

REC

OPEN/CLOSE

DVD

T 1

• If you perform an invalid operation during erasing, the SEND/

LEARN indicator flashes three times quickly, and the remote

controller exits the erasing mode. Resume from Step 1.

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

• If many commands have been programmed to the MODE

button, then the SEND/LEARN indicator may remain lit for up

to 20 seconds during Step 2. This is not a malfunction.

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

ENTER

HOME THEATER CONTROLLER

RC 447M

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a Macro function

Programming a Macro function

What is a Macro function?

A Macro function enables you to program a series of button

operations (up to 16) on the remote controller into a single button.

For example, to play a compact disc player connected to the TX-

DS595 normally, you must perform the following steps:

You can program a different macro into the MODE MACRO button

for each of the eight MODE buttons. The macro is then executed by

pressing the appropriate MODE button and then pressing the MODE

MACRO button. For example, to program the macro described

above into the CD MODE button, perform the steps given below.

1. Press the RCVR MODE button.

2. Press the ON button.

1. Press and hold down the desired MODE button (in

this case, the CD MODE button), press the MODE

MACRO button, and then release both buttons.

3. Press the CD (INPUT SELECTOR) button.

4. Press the CD MODE button.

5. Press the playback ( ) button.

When you press the CD MODE button, the SEND/LEARN

indicator lights and the CD MODE button lights green. When

you press the MODE MACRO button, the indicator turns off.

When you release the buttons, the indicator flashes and lights

again.

By using the macro function, you can perform the above five

operations by only pressing two buttons.

2. Press the operation buttons you wish to program in

order (in this case, press RCVR MODE → ON → CD

(INPUT SELECTOR) → CD MODE → playback (

button).

)

When you press each button, the SEND/LEARN indicator turns

off. When you release the button, the indicator lights.

3. Press the MODE MACRO button to complete the

programming.

MODE MACRO

CD MODE

RCVR MODE

The SEND/LEARN indicator flashes twice slowly.

4. Run the macro to check to see if the macro has been

properly programmed.

DISC

VOL

Notes:

AUDIO

MUTING

• You may program up to 16 button operations into each macro

function. If you try to program a 17th operation, it will be

ignored, and programming is stopped.

ANGLE

SUBTITLE

TV/VCR

LEVEL

(CD playback)

(INPUT

SELECTOR)

• If no button is pressed for more than 30 seconds during the

programming, the SEND/LEARN indicator flashes three times

quickly, and the remote controller exits the programming mode.

Resume from Step 1.

RANDOM

REC

OPEN/CLOSE

DVD

T 1

• If you perform an invalid operation during programming, the

SEND/LEARN indicator flashes three times quickly, and the

remote controller exits the programming mode. Resume from

Step 1.

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Running a Macro function

Perform the procedure below to run a macro function that you have

programmed into the remote controller. After programming a macro,

you should always run it at least once to make sure that it has been

programmed properly.

Tips:

• If you erase or change the command of a button programmed in

a macro, that operation of that button will no longer work in the

macro. In this case, it will be necessary for you to reprogram the

macro in order to avoid incorrect operation.

1. Point the remote controller at the TX-DS595 and

press the CD MODE button.

• The codes programmed into a macro will be transmitted at an

interval of 0.5 seconds. However, some devices may not be able

to complete one operation in 0.5 seconds and may miss the next

code. In this case, after pressing one operation button, you can

press the same MODE button again before pressing the next

operation button to add another 0.5 seconds between the two

operations.

2. Press the MODE MACRO, and verify that the devices

operate properly.

It may take a while for the macro to finish transmitting, so be

sure to continue pointing the remote controller at the device until

the SEND/LEARN indicator turns off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a Macro function

Programming the Direct Macro function

With the direct macro function, you can program a series of button

operations as a macro into the DIRECT MACRO button so the

macro can be executed with just one touch. Note that for the direct

macro function, only one macro can be programmed. For example,

to program the macro described on the previous page for the

DIRECT MACRO button, perform the steps given below.

CD MODE

DIRECT

MACRO

MODE buttons

1. Press and hold down any one of the eight MODE

buttons, press the DIRECT MACRO button, and then

release both buttons.

RCVR MODE

DISC

VOL

When you press the MODE button, it lights green and the

SEND/LEARN indicator lights. When you press the DIRECT

MACRO button, the indicator turns off. When you release the

buttons, the indicator flashes briefly and then lights again.

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

(CD playback)

2. Press the operation buttons you wish to program in

RANDOM

REC

OPEN/CLOSE

order (in this case, press RCVR MODE → ON → CD

(INPUT SELECTOR) → CD MODE → playback (

)

DVD

button).

(INPUT

T 1

When you press each button, the SEND/LEARN indicator turns

off. When you release the button, the indicator lights.

SELECTOR)

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

3. Press the DIRECT MACRO button to complete the

procedure.

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

The SEND/LEARN indicator flashes twice slowly.

HOME THEATER CONTROLLER

RC 447M

4. Check to see if the macro has been properly

programmed.

Notes:

Tips:

• You may program up to 16 button operations into the direct

macro function. If you try to program a 17th operation, it will be

ignored, and programming is stopped.

• If you erase or change the command of a button programmed in

the direct macro, that operation of that button will no longer

work in the macro. In this case, it will be necessary for you to

reprogram the direct macro in order to avoid incorrect operation.

• If no button is pressed for more than 30 seconds during the

programming, the SEND/LEARN indicator flashes three times

quickly, and the remote controller exits the programming mode.

Resume from Step 1.

• The codes programmed into a direct macro will be transmitted at

an interval of 0.5 seconds. However, some devices may not be

able to complete one operation in 0.5 seconds and may miss the

next code. In this case, after pressing one operation button, you

can press the same MODE button again before pressing the next

operation button to add another 0.5 seconds between the two

operations.

• If you perform an invalid operation during programming, the

SEND/LEARN indicator flashes three times quickly, and the

remote controller exits the programming mode. Resume from

Step 1.

Running a Direct Macro function

Perform the procedure below to run a direct macro function that you

have programmed into the remote controller. After programming a

direct macro, you should always run it at least once to make sure that

it has been programmed properly.

1. Point the remote controller at the TX-DS595 and

press the DIRECT MACRO button.

It may take a while for the macro to finish transmitting, so be

sure to continue pointing the remote controller at the device until

the SEND/LEARN indicator turns off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a Macro function

Erasing a macro from the MODE MACRO button

1. Press and hold down the desired MODE button,

press the MODE MACRO button, and then release

both buttons.

When you press the MODE button, it lights green and the

SEND/LEARN indicator lights. When you press the MODE

MACRO button, the indicator turns off. When you release the

buttons, the indicator flashes once.

MODE MACRO

MODE buttons

2. Press the MODE MACRO button again.

DISC

VOL

The SEND/LEARN indicator flashes twice slowly. The macro

programmed to the MODE button pressed in Step 1 above is

erased.

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

Notes:

• If no button is pressed for more than 30 seconds during the

erasing procedure, the SEND/LEARN indicator flashes three

times quickly, and the remote controller exits the erasing mode.

Resume from Step 1.

RANDOM

REC

OPEN/CLOSE

DVD

• Be aware that if you press a button other than MODE MACRO

button in Step 2, then you will in effect be overwriting the

previous macro with a new macro.

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Erasing a direct macro from the DIRECT

MACRO button

1. Press and hold down any one of the eight MODE

buttons, press the DIRECT MACRO button, and then

release both buttons.

When you press the MODE button, it lights green and the

SEND/LEARN indicator lights. When you press the DIRECT

MACRO button, the indicator turns off. When you release the

buttons, the indicator flashes once.

DIRECT

MACRO

MODE buttons

2. Press the DIRECT MACRO button again.

DISC

VOL

The SEND/LEARN indicator flashes twice slowly. The macro

programmed to the DIRECT MACRO button is erased.

AUDIO

MUTING

ANGLE

SUBTITLE

TV/VCR

LEVEL

Notes:

• If no button is pressed for more than 30 seconds during the

erasing procedure, the SEND/LEARN indicator flashes three

times quickly, and the remote controller exits the erasing mode.

Resume from Step 1.

RANDOM

REC

OPEN/CLOSE

DVD

• Be aware that if you press a button other than DIRECT MACRO

button in Step 2, then you will in effect be overwriting the

previous direct macro with a new direct macro.

T 1

TUN

STEREO

DIRECT

DSP

SURR

A.ST

DSP

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

HOME THEATER CONTROLLER

RC 447M

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a Macro function

Erasing all commands and macros that have

been programmed

This procedure will erase all the commands and macros that you

have programmed into the remote controller and return it to its

default settings. This operation will not affect the preset settings of

the remote controller.

STDBY

1. Open the battery cover and remove the batteries from

the remote controller.

2. While pressing and holding down the ON and STDBY

buttons, re-insert the batteries in their correct

orientation, and then release both buttons.

DISC

VOL

AUDIO

MUTING

The SEND/LEARN indicator flashes slowly.

ANGLE

SUBTITLE

TV/VCR

LEVEL

3. Press the ENTER button.

The SEND/LEARN indicator lights up for about ten seconds and

then turns off.

RANDOM

REC

OPEN/CLOSE

DVD

All programmed commands and macros are erased and the remote

controller returns to its factory presets.

T 1

TUN

STEREO

DIRECT

DSP

Notes:

SURR

A.ST

DSP

• Proceed to Step 3 immediately after Step 2; otherwise, the

batteries will be consumed quickly.

SPA

SP B

Re-EQ

DISPLAY

DIMMER

ZONE

ENTER

-- ---

• If you press any button other than the ENTER button in Step 3,

nothing will be erased. In this case, resume from Step 1.

ENTER

HOME THEATER CONTROLLER

RC 447M

Macro mode programming memo:

MACRO

MODE

MACRO

↓

DIRECT

MACRO

MACRO MACRO MACRO MACRO MACRO MACRO MACRO

↓

RCVR

DVD

SAT

CABLE

VCR

Operation 1

Operation 2

Operation 3

Operation 4

Operation 5

Operation 6

Operation 7

Operation 8

Operation 9

Operation 10

Operation 11

Operation 12

Operation 13

Operation 14

Operation 15

Operation 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

AMPLIFIER SECTION

TUNER SECTION

Continuous Average Power output (FTC)

All channels:

75 W per channel min. RMS at

Tuning Range:

Usable Sensitivity

Mono:

87.5 to 108.0 MHz (50-kHz steps)

8 Ω, 2 channels driven from 20

Hz to 20 kHz with no more than

0.08% total harmonic distortion.

100 W min. RMS at 6 Ω, 2

channels driven from 1 kHz with

no more than 0.1% total

11.2 dBf, 1.0 µV (75 Ω IHF)

0.9 µV (75 Ω DIN)

17.2 dBf, 2.0 µV (75 Ω IHF)

23 µV (75 Ω DIN)

Stereo:

50 dB Quieting Sensitivity

Mono:

Stereo:

harmonic distortion.

17.2 dBf, 2.0 µV (75 Ω)

37.2 dBf, 20 µV (75 Ω)

2.0 dB

Continuous Power output (DIN) 110 W at 6 Ω

Maximum Power output (EIAJ) 140 W at 6 Ω

Dynamic Power Output (Stereo) 2 × 210 W at 3 Ω

2 × 155 W at 4 Ω

Capture Ratio:

Image Rejection Ratio:

USA & Canadian models:

Other area models:

IF Rejection Ratio:

Signal-to-Noise Ratio

Mono:

40 dB

85 dB

90 dB

2 × 90 W at 8 Ω

Total Harmonic Distortion:

IM Distortion:

0.08% at rated power

0.08% at 1 W output

0.08% at rated power

0.08% at 1 W output

60 at 8 Ω

76 dB

70 dB

Stereo:

Damping Factor:

Input Sensitivity and Impedance

PHONO:

LINE (CD, TAPE, DVD,

VIDEO 1, 2, 3):

MULTICHANNEL INPUT

(FRONT L/C/R, SURROUND

L/R):

Alternate Channel Attenuation: 55 dB

Selectivity:

AM Suppression Ratio:

Total Harmonic Distortion

Mono:

Stereo:

Frequency Response:

Stereo Separation:

50 dB (DIN)

50 dB

2.5 mV, 50 kΩ

200 mV, 50 kΩ

0.2%

0.3%

30 Hz to 15 kHz, 1.0 dB

45 dB at 1 kHz

30 dB at 100 Hz to 10 kHz

200 mV, 50 kΩ

36 mV, 50 kΩ

(SUBWOOFER):

COAXIAL 1, 2 (DIGITAL): 0.5 Vp-p, 75 Ω

DVD, VIDEO1, 2, 3:

Tuning Range

USA & Canadian models:

European & Australian models

Worldwide models:

1 Vp-p, 75 Ω

1 Vp-p, 75 Ω (Y)

0.28 Vp-p, 75 Ω (C)

530 to 1,710 kHz (10-kHz steps)

522 to 1,611 kHz (9-kHz steps)

531 to 1,602 kHz (9-kHz steps)

530 to 1,710 kHz (10-kHz steps)

Output Level and Impedance

Rec out (TAPE, VIDEO 1):

200 mV, 2.2 kΩ

Usable Sensitivity:

Image Rejection Ratio:

IF Rejection Ratio:

Signal-to-Noise Ratio:

Total Harmonic Distortion:

30 µV

40 dB

0.7%

Pre out:

1 V, 470 Ω

VIDEO (VIDEO 1, MONITOR OUT):

1 Vp-p, 75 Ω

1 Vp-p, 75 Ω (Y)

0.28 Vp-p, 75 Ω (C)

180 mV RMS at 1 kHz, 0.5% T.H.D.

10 Hz to 100 kHz: +1 dB,-3 dB

20 Hz to 20 kHz : 0.8 dB

GENERAL

Power Supply:

Phono Overload:

Frequency Response:

RIAA Deviation:

Tone Control

Bass:

AC 120 V, 60 Hz

(USA & Canadian models)

AC 230-240 V, 50 Hz

(European & Australian models)

AC 220-230 V, 50/60 Hz

(some Asian models)

AC 220-230 and 120 V switchable,

50/60 Hz (Worldwide models)

4.7 A

380 W

435 × 175 × 431 mm

17-1/8" × 6-7/8" × 16-15/16"

25.4 lbs. (USA & Canadian models)

12.5 kg (Other models)

10 dB at 50 Hz

10 dB at 20 kHz

Treble:

Signal-to-Noise Ratio (Stereo)

Phono:

CD/Tape:

80 dB (IHF A, 5 mV input)

100 dB (IHF A, 0.5 V input)

–50 dB

Power Consumption:

Dimensions (W × H × D):

Weight:

Muting:

REMOTE CONTROLLER

Transmitter:

Signal range:

Power supply:

Infrared

Approx. 5 meters, 16 ft.

Two “AA” batteries (1.5 V × 2)

Specifications and features are subject to change without notice.

Power supply and voltage vary depending on the area in which the unit

is purchased.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting guide

If a problem occurs while you are using the remote controller, first

try to operate the controls on the front panel of the TX-DS595 to

make sure that it is not due to a malfunction (or worn out batteries) in

the remote controller.

Low frequency humming is heard.

• Not properly grounded.

• Turntable motor is not properly grounded.

• Audio connection cables on the rear panel are connected

incorrectly.

POWER

Power shuts off immediately after power on.

Howling is heard when the volume is turned up.

• Amplifier protection circuitry has been activated.

your Onkyo service center.

• Turntable and speakers are located too close together.

Rough or scratchy sound is heard. High range is not

clear.

No power.

• Power cord is disconnected.

• The needles of turntable is dirty or worn, or a problem exists

with a connected component.

• External noise in the affecting the internal microcomputer.

power cord from the outlet and then plug it in again.

check for problem.

• Treble control is too high.

• Internal fuse is blown.

Power turns on but no sound.

• “MUTING” is displayed.

FM/AM TUNER

off.

AM stations cannot be received.

• Bad connections or wiring.

• AM loop antenna is not connected.

terminals.

• Amplifier protection circuitry has been activated.

Buzzing noise on AM stations (particularly noticeable at

night or with weak stations).

The sound of the playback source is not heard.

• Input selector is not set properly.

• Noise from electrical apparatus such as fluorescent lamp.

• Headphones are connected.

Noise is heard at high-pitched sounds on AM stations.

Pressing the ON button on the remote controller does

not turn on the power to the main unit.

• Noise from TV set.

• You have not pressed RCVR MODE button.

Crackling noise on both AM and FM stations.

• Noise caused by fluorescent lamp being turned on and off.

SPEAKERS

• Noise from automobile ignition.

road.

No sound from the center speaker, or at very low

volume.

• Speaker cable is not connected.

The indicators light for stereo reception, but sound is

distorted and stereo separation is bad.

• Listening mode is set to Stereo or Direct.

Direct. The output to the center speaker may differ depending

on the listening mode.

• Station is too strong.

• Multiple reflection of the radio waves because of tall buildings

or mountains.

• Center speaker level is set to minimum.

where distortion is least.

20).

Indicators for stereo reception flicker and hiss is heard

on FM stations.

• Center speaker is set to “NONE.”

• Station is too weak.

No sound or very low volume from subwoofer.

• Stereo FM broadcasts cover only about half the distance of an

ordinary broadcast.

• Subwoofer is set to “NO.”

• Subwoofer speakers output level setting is improper.

(page 19).

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting guide

No preset station is recalled.

Re-EQ function cannot be used.

• Power cord has been unplugged or the POWER switch has been

turned off for a long time.

• Re-EQ is only enabled for Analog/PCM sources and Dolby

Digital surround.

Multichannel audio is not output.

• To listen to multichannel audio, “YES” must be selected in the

Multichannel in the Audio Setup of the Input Setup. Also, it is

necessary to select Multichannel with the AUDIO SELECTOR

button.

CHANNEL INPUT port and check the setup settings.

VIDEO and AUDIO

Desired picture does not appear.

• Improper connection.

completely.

Picture and sound do not match.

If one of the messages shown below appears

• Improper connection.

“NOT AVAILABLE WITH HEADPHONES USE”

No sound, or sound of the selected source is not heard.

The operation is not allowed because headphones are plugged into

the TX-DS595.

• Audio Setup of Input Setup settings are incorrect.

“NOT AVAILABLE WITH MULTICHANNEL USE”

No picture appears on the TV screen (or monitor).

The operation is not allowed because the selected input source is set

for multichannel input.

• TV (or monitor) is not set to receive the output signals from the

receiver.

“NOT AVAILABLE IN THIS SP CONFIG”

• Video cable is not connected securely.

The operation is not allowed by the current speaker configuration.

“NOT AVAILABLE IN THIS LISTENING MODE”

• The video input and output connections are incorrect.

your television monitor must be connected to S VIDEO OUT.

If your video component is connected to VIDEO IN, then

your television monitor must be connected to VIDEO OUT.

Be aware that the signal input to S VIDEO IN is not output

from VIDEO OUT and the signal input to VIDEO IN is not

output from S VIDEO OUT.

This operation cannot be performed in this listening mode.

“NOT AVAILABLE WITH THIS SIGNAL”

This operation cannot be performed with this input signal.

Also refer to the respective instruction manuals of the compact disc

player, DVD player, video cassette recorder, TV monitor, etc., that

compose your entertainment system.

The TX-DS595 contains an internal microcomputer that performs

high-level operations. However, on extremely rare occasions, noise

or interference from an external source or static electricity may cause

faulty operation. If this occurs, unplug the power cord from the wall

outlet, wait five or more seconds, and then plug it back in. This

should correct the situation.

REMOTE CONTROLLER

Front panel controls function but remote controller

controls do not.

* To reset the surround mode and other settings to the factory

default settings, hold down the PRESET MEMORY button with

the TX-DS595 turned on and then press the STANDBY/ON

button. “CLEAR” appears in the front display and the TX-

DS595 enters the standby state.

• No batteries in remote controller.

• Batteries have worn out.

• Remote controller is not pointed at the remote sensor of the TX-

DS595.

• Remote controller is too far from the TX-DS595.

• Remote controller is functioning in a different mode

OTHER

LATE NIGHT function cannot be used.

• Playback source is not Dolby Digital encoded.

display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8111 Fax: 072-833-5222

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 E-mail: [email protected]

ONKYO EUROPE ELECTRONICS GmbH

Industriestrasse 20, 82110 Germering, GERMANY

Tel: 089-849-320 Fax: 089-849-3265 E-mail: [email protected]

ONKYO CHINA LIMITED

Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039

HOMEPAGE

http://www.onkyo.co.jp/

D0104-2

SN 29343023A

Download from Www.Somanuals.com. All Manuals Search And Download.

MTD Lawn Mower 111 902 026 User Manual
Murphy Automobile Parts DT9803 User Manual
Omega Vehicle Security Stereo System OMWT DIPOLE 900 25 User Manual
Onkyo Speaker SKC L500C User Manual
Panasonic Fax Machine KX FLB751AL User Manual
Panasonic Scanner KV S6050W User Manual
Panasonic Security Camera BB HGW700A User Manual
ParaBody Home Gym PBF405B User Manual
Paradyne Modem 3800Plus User Manual
Patton electronic Network Card 1010A User Manual