Contents
Stereo Receiver
Introduction.................................... 2
TX-8255
Instruction Manual
Connections................................. 12
Enjoying Audio Sources.............. 19
Others
Troubleshooting .............................. 31
Specifications.................................. 33
Thank you for purchasing an Onkyo Stereo Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Stereo Receiver.
Please retain this manual for future reference.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal
without the permission of the copyright holder.
For U.S. models
FCC Information for User
CAUTION:
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical solvents,
because they may damage the finish or remove the
panel lettering.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230, 50 Hz or AC 120 V, 60 Hz).
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV tech-
nician for help.
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
•
•
Some models have a voltage selector for
compatibility with power systems around the world.
Before you plug in such a model, make sure that the
voltage selector is set to the correct voltage for your
area.
For Canadian Models
Pressing the [ON/STANDBY] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Modèle pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Precautions—Continued
For British models
Introduction
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
Important Safety Instructions ...........................2
Precautions.........................................................3
Table of Contents...............................................4
Supplied Accessories........................................5
Installing the Batteries ...........................................5
Features ..............................................................5
Getting to Know the Receiver...........................6
Front Panel............................................................6
Rear Panel.............................................................8
Display...................................................................9
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
Remote Controller............................................10
Using the Remote Controller ...............................11
Connections
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
Connecting Your Speakers .............................12
Speaker Connection Precautions........................12
Connecting the Speaker Cables..........................12
Connecting Antenna........................................13
Connecting the Indoor FM Antenna.....................13
Connecting the AM Loop Antenna.......................13
Connecting an Outdoor FM Antenna...................14
Connecting an Outdoor AM Antenna...................14
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
Connecting Your Components .......................15
Connecting a Turntable .......................................15
Connecting a CD Player......................................15
Connecting a Recording Component ..................16
Connecting a Remote Interactive Dock (RI Dock).....16
Connecting a DVD Player....................................16
Connecting a TV or Other Component with an Audio
Output.............................................................17
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must approved
by ASTA or BSI to BS1362 and have the same ampere
rating as that indicated on the plug. Check for the ASTA
mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
Connecting
Components..............................17
Connecting the Power Cords of Other
Components ...............................................18
Connecting the Power Cord ................................18
For European Models
Declaration of Conformity
Enjoying Audio Sources
We,
ONKYO EUROPE
Turning On the Receiver .................................19
Turning On and Standby .....................................19
Changing the Input Display .................................19
Enjoying Audio Sources..................................20
Muting the receiver (remote controller only)........21
Using Headphones..............................................21
Setting the Display Brightness.............................21
Using the Sleep Timer (remote controller only)...21
Using the Tone and Balance Controls.................22
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
EN55013, EN55020 and EN61000-3-2, -3-3.
technical standards such as EN60065,
Recording .........................................................23
Recording the Input Source.................................23
GROEBENZELL, GERMANY
Listening to the Radio .....................................25
AM Frequency Step Setup (not North America and
Europe)...........................................................25
Listening to AM/FM Stations................................25
Using RDS (European Models Only)...................27
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
Naming Preset Channels (other than European
model).........................................................29
Entering a Name..................................................29
Correcting a Character ........................................29
Connecting Components not Reached by the
Remote Controller Signals (IR IN/OUT)..... 30
If Remote Controller Signal Does not Reach the
Receiver Remote Sensor................................30
If Remote Controller Signal Does not Reach Other
Components ...................................................30
Others
Troubleshooting...............................................31
Specifications...................................................33
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
Supplied Accessories
• If the remote controller doesn’t work reliably, try
replacing the batteries.
Make sure you have the following accessories:
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or
corrosion.
Remote controller and two batteries (AA/R6)
Indoor FM antenna
Features
❑ Newly Designed, Brushed Hairline Aluminum
Front Panel
❑ 50 Watts/Channel @ 8 ohms (FTC)
(North American model)
AM loop antenna
*
In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and
operation are the same regardless of color.
❑ 90 Watts/Channel @ 4 ohms (IEC)
(European and Australian model)
❑ WRAT (Wide Range Amplifier Technology)
❑ High-Current, Low-Impedance Drive
❑ Discrete Output Stage Circuitry
❑ 5 Audio Inputs (CD, TAPE 1, TAPE 2, LINE 1/
DVD, LINE 2) and 2 Outputs
Installing the Batteries
Detach the battery cover by pressing the
tab and pulling up the cover.
1
❑ Phono Input
❑ Speaker A/B Terminals
❑ RDS (PS/PTY/RT/TP) (European model)
❑ IR Input/Output
❑ Banana Plug-Compatible Speaker Posts
(North American model)
❑ Compatible with RI Dock for the iPod
Insert two AA-size batteries into the
battery compartment.
2
Carefully follow the polarity diagram (positive +
and negative - symbols) inside the battery
compartment.
After batteries are installed and seated
correctly, attach the compartment cover.
3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the Receiver
Front Panel
North American Model
1
2
3 4
5
6 7 8 9
J
R
Q
P
O
N M L
K
* The name of the buttons and other controls varies according to the shipping destination. For details,
refer to the description on the next page.
Other Models
1
2
3 4
5
6 7 8 9
J
R
Q
P
O
N M L
K
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the Receiver—Continued
Some button number sections (such as 7and 9)
contain multiple button descriptions because the name
and function vary according to the model or shipping
destination. Refer to the description corresponding to
your model.
H Number buttons (26, 29)
Used to select a station by entering the frequency
directly or to enter characters to label the station
preset number.
I DIMMER button (21)
For detailed information, see the pages in parentheses.
Adjusts the display brightness.
A ON/STANDBY button (19)
SCAN button (28)
Used to find a station in RDS broadcasting.
Sets the receiver to On or Standby.
B SPEAKERS A and B switches (20)
J MASTER VOLUME control (20)
Turn speaker sets A and B on or off.
Sets the volume of the receiver.
C Remote-control sensor (11)
K BALANCE control (22)
Receives control signals from the remote controller.
This control is for adjusting the sound level balance
between the left and right channel for speakers and
headphones.
D DISPLAY (27)
Displays various information about the currently
selected input source.
L TREBLE control (22)
This control is for adjusting the level of treble
sounds.
E TUNING UP/DOWN buttons (25, 28)
Used for radio tuning.
M BASS control (22)
This control is for adjusting the level of bass
sounds.
F DIRECT TUNING button (26)
When you know the frequency for the station you
want to listen to, you can select the station by
entering the frequency directly using this button and
number buttons. When SAT RADIO is selected, you
can select the channel number.
N TUNING MODE button (25, 26)
Selects the Auto or Manual tuning mode for AM
and FM radio.
G CHARACTER button
O MEMORY button (26)
Used to label the FM or AM station preset number.
Used when storing or deleting radio presets.
RT/PTY/TP button (28)
P Input selector buttons (20, 23)
On the European model, this is the RT/PTY/TP
button, and it’s used with RDS (Radio Data
System). See “Using RDS (European Models
Only)” on page 27.
Used to select the input sources.
The TAPE 2 MONITOR button is also used to
monitor the recorded sound.
Q STANDBY indicator (19)
Lights up when the receiver is on Standby and
flashes while a signal is being received from the
remote controller.
R PHONES jack (21)
This 1/4-inch phone jack is for connecting a
standard pair of stereo headphones for private
listening.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the Receiver—Continued
Rear Panel
1 2
3
4
5
67 8 9J
K
L
H TAPE 1/2 IN/OUT
A
REMOTE CONTROL jacks
These (Remote Interactive) jacks can be
connected to the jacks on your other Onkyo
audio components. The receiver’s remote controller
can then be used to control all of your components.
This analog audio input and output are for
connecting a recorder with an analog audio input
and output, such as a cassette deck, MD recorder,
etc.
I LINE 1/DVD
To use
, you must make an analog audio
connection between the receiver and each
component.
This analog audio input is for connecting a
component’s analog audio output (DVD, RI Dock,
etc.).
B IR IN/OUT
A commercially available IR receiver can be
J LINE 2 input
connected to the IR IN jack, allowing you to control
the receiver when it’s out of sight, for example,
installed in a cabinet.
This analog audio input is for connecting a
component’s analog audio output (TV, etc.).
K SPEAKERS A
A commercially available IR emitter can be
connected to the IR OUT jack to pass IR (infrared)
remote control signals along to other components.
These terminal posts are for connecting speaker
set A.
L SPEAKERS B
C AM ANTENNA
These terminal posts are for connecting speaker
set B.
These push terminals are for connecting an AM
antenna.
D FM ANTENNA
See pages 12–18 for hookup information.
This jack is for connecting an FM antenna.
E AC OUTLET
This switched AC outlet can be used to supply
power to another component. The type of outlet
depends on the country in which you purchased
your receiver.
F PHONO (MM) input and grounding terminal
This analog audio input is for connecting a turntable
with a moving-magnet cartridge. The screw located
on the upper-right of the PHONO (MM) inputs is
for connecting a turntable’s ground wire.
G CD input
This analog audio input is for connecting a CD
player’s analog audio output.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the Receiver—Continued
Display
1
2
3
4
5
For detailed information, see the pages in parentheses.
4 SLEEP indicator
Lights up when the Sleep function has been set.
1 A and B speaker indicators
Indicator A lights up when speaker set A is on.
Indicator B lights up when speaker set B is on.
5 Message area
Displays various information about the selected
input source.
2 MUTING indicator
Flashes while the receiver is muted.
3 Radio indicators
TUNED: Lights up when tuned to a radio station.
AUTO: For AM and FM radio, lights up when Auto
Tuning is selected, and disappears when Manual
Tuning mode is selected.
RDS (European models only): Lights up when
tuned to a radio station that supports RDS (Radio
Data System).
MEMORY: Lights up when presetting radio
stations.
FM STEREO: Lights up when tuned to a stereo
FM station.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
For detailed information, see the pages in parentheses.
A STANDBY/ON button (19)
Sets the receiver to On or Standby.
B SLEEP button (21)
Used with the Sleep function.
C INPUT SELECTOR buttons (20) and number
buttons (26)
1
7
When any of these buttons is pressed, the input
source will be changed to the one shown below the
button. The button with no label does not work for
input source selection. After the DIRECT TUNING
button is pressed, these buttons work as number
button for about 5 seconds. During this time, the
buttons can be used to select AM and FM radio
stations and satellite radio channels directly.
2
8
9
3
J
K
D CLR button (25)
4
5
Used to enter the station frequency directly or
cancel the number entry.
E HDD PLAYLIST [ ]/[ ] buttons
Selects a playlist stored on the player on an HDD
component.
L
M
F CD operation buttons
N
O
RANDOM: Used with the random playback
function.
P
REPEAT: Used with the repeat playback functions.
DISC SKIP: Switches the disc loaded when the CD
changer is connected.
[
[
[
]: Suspends playback on a CD.
]: Stops playback on a CD.
]: Starts playback on a CD.
Q
R
G DIMMER button (21)
Adjusts the display brightness.
6
H DISPLAY button (27)
Displays various information about the selected
input source.
I TUNING [ ]/[ ] buttons (25)
When AM or FM is selected, the TUNING UP
[
]/DOWN [ ] buttons are used for radio tuning.
J PRESET [ ]/[ ] buttons (26)
Used to select radio presets.
K DIRECT TUNING button (26)
When you know the frequency for the station you
want to listen to, you can select the station by
entering the frequency directly using this button and
number buttons. When SAT RADIO is selected, you
can select the channel number.
L HDD ALBUM [ ]/[ ] buttons
Selects an album stored on the player on an HDD
component.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
M Previous and Next [
]/[
] buttons
Using the Remote Controller
These buttons are used to select the previous or next
track on an HDD component. Pressing them
repeatedly selects earlier or later tracks. On a
cassette deck, they’re used for rewind and fast
forward.
Point the remote controller toward the remote control
sensor.
Remote control sensor
N Reverse and Fast Forward [ ]/[ ] buttons
These buttons are used for reverse and fast forward
on an HDD component.
O DECK A/HDD (DOCK) buttons
Pause [ ]/Reverse Play [ ]: Suspends playback
on an HDD component; starts reverse playback on a
cassette deck.
About 5 m
(16 f
eet)
Notes:
Play [ ]: Starts playback on an HDD or cassette
component.
• The remote controller may not work reliably if the
receiver is subjected to bright light, such as direct
sunlight or inverter-type fluorescent lights. Keep this
in mind when installing.
Stop [ ]: Stops playback on an HDD or cassette
component.
• If another remote controller of the same type is used
in the same room, or the receiver is installed close to
equipment that uses infrared rays, the remote
controller may not work reliably.
P DECK B buttons
On twin cassette decks, only deck B can be
controlled.
Play [ ]: Starts playback.
• Don’t put anything, such as a book, on the remote
controller, because the buttons may be pressed
inadvertently, thereby draining the batteries.
Stop [ ]: Stops playback.
Reverse Play [ ]: Starts reverse playback.
• The remote controller may not work reliably if the
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
Q MUTING button (21)
Mutes or unmutes the receiver.
R VOLUME [ ]/[ ] buttons (20)
The remote controller will not work if there’s an obstacle
between it and the receiver’s remote control sensor.
Adjusts the volume of the receiver regardless of the
currently selected remote controller mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers
Disconnect the power cord from the wall outlet before making any connections.
Speaker Connection Precautions
Connecting the Speaker Cables
The receiver allows you to connect two sets of speakers.
When two sets of speakers are connected, you can select
which speaker set outputs sound or use both sets to
output sound simultaneously.
• When you connect one set of speakers to either
SPEAKERS A or SPEAKERS B terminal posts, or
when you connect two sets of speakers to both speaker
terminal posts and output sound only from either
speaker set, use speakers whose impedance is between
4 and 16 ohms.
Strip about 15 mm (5/8
inch) of insulation from
the ends of the speaker
cables, and twist the bare
wires tightly, as shown.
15 mm
(5/8")
1
Unscrew the terminal.
2
3
• When you connect speakers to both SPEAKER A and
SPEAKER B terminal posts and output sound from
both speaker sets simultaneously, use speakers whose
impedance is between 8 and 16 ohms.
Fully insert the bare
wires.
Note:
If you make an incorrect setting for the speakers or the
impedance values, the built-in protection circuit may be
activated resulting in no sound output from speakers.
Screw the terminal tight.
4
The following illustration shows which speaker should
be connected to each pair of terminals.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to
negative (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
Left
speaker
Right
speaker
Speaker set A
–
+
–
+
• Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the
positive and negative wires.
Doing so may damage the
receiver.
• Don’t connect more than one
cable to each speaker
terminal. Doing so may
damage the receiver.
• Don’t connect a speaker to more than one pair of
speaker terminals.
Receiver
–
+
–
+
Right
speaker
Left
speaker
Speaker set B
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antenna
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The receiver won’t pick up any radio signals without any
antenna connected, so you must connect the antenna to
use the tuner.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
AM antenna push terminals
FM antenna connector
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
2
Connecting the Indoor FM Antenna
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around.)
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
■ North American Model
1
Insert the plug fully
into the jack.
Push
Insert wire
Release
■ Other Models
Insert the plug fully
into the jack.
Once your receiver is ready for use, you’ll need to
tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception.
Once your receiver is ready for use, you’ll need to
tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from
your receiver, TV, speaker cables, and power
cords.
Use thumbtacks or something similar to
fix the FM antenna into position.
2
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a
commercially available outdoor AM antenna (see
page 14).
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available
outdoor FM antenna instead (see page 14).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antenna—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available
outdoor FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor antenna
FM 75
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in
an attic or loft.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from
possible noise sources, such as neon signs, busy roads,
etc.
Outdoor AM antennas work best when installed outside
horizontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock
hazards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If
circumstances demand it, use a TV/FM antenna splitter,
as shown.
TV/FM antenna splitter
To the receiver
To TV (or VCR)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components
Before Making any Connections
Connecting a Turntable
• Always refer to the instructions that came with the
component that you are connecting.
• Do not plug in the power cord until all connections
have been properly made.
• Do not bind audio cables with power cords and
speaker cables. Doing so may adversely affect the
sound quality.
The receiver’s PHONO input jacks are for use with
moving-magnet (MM) type cartridges.
Use an analog audio cable to connect the receiver’s
PHONO L/R jacks to the audio output jacks on the
turntable, as shown.
• To prevent interference, keep power cords and
speaker cables away from the tuner’s antenna.
Connection Color Coding
Use red plugs to connect right-channel audio inputs and
outputs (typically labeled “R”). Use white plugs to
connect left-channel audio inputs and outputs (typically
labeled “L”).
AUDIO OUT
Analog audio
Left (white)
Right (red)
Left (white)
Right (red)
Ground wire
Notes:
• If the turntable has a ground wire, connect it to
receiver’s GND terminal. With some turntables,
connecting the ground wire may cause hum, in which
case it should be disconnected.
• Push each plug in all the way to make a good
connection (loose connections can cause noise or
malfunctions).
Right!
• If the turntable has a moving-coil (MC) type cartridge,
you’ll need a commercially available MC phono
preamp. In this case, connect the turntable to the
phono preamp’s input, and connect the phono
preamp’s output to the receiver’s PHONO L/R jacks.
Wrong!
Connecting a CD Player
Use an analog audio cable to connect the receiver’s CD
L/R jacks to the analog audio output jacks on the CD
player, as shown.
ANALOG
OUT
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Recording Component
Connecting a DVD Player
To connect recording components, such as cassette deck,
MD recorder and CD recorder, use an analog audio cable
to connect the receiver’s TAPE 1 or 2 IN L/R jacks to the
cassette deck’s analog audio output jacks, and use
another analog audio cable to connect the receiver’s
TAPE 1 or 2 OUT L/R jacks to the cassette deck’s analog
audio input jacks, as shown.
Only audio input from the DVD player can be received.
The video input from the DVD player should be
connected to the TV directly.
Use an analog audio cable to connect the LINE 1/DVD
IN L/R jacks to the analog audio output jacks on the
DVD player.
When you want to monitor the recorded sound, use the
TAPE 2 jacks for connecting a recorder.
IN
L
R
LINE 1
/DVD
L
R
AUDIO
OUT
/
REC
(IN)
PLAY
(OUT)
Connecting a Remote Interactive
Dock (RI Dock)
Use an analog audio cable to connect the TAPE 1 IN L/R
jacks to the RI Dock’s analog audio output jacks. Then
use an
RI Dock’s
cable to connect the receiver’s
jack, as shown.
jack to the
When you change the input display name to “HDD,” you
can operate the RI Dock using the remote controller
supplied with the receiver (see page 19).
TAPE 1
R
----
L
RemoteInteractive
Dock
AUDIO OUT
Note:
If you use the Onkyo Remote Interactive Dock (DS-A1),
flip the RI MODE switch to “HDD” which is located on
the underside.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
With
(Remote Interactive), you can control your
Connecting aTV or Other Component
with an Audio Output
-compatible Onkyo CD player, RI Dock, and so on
with the receiver’s remote controller.
• To use , you must make an analog audio
connection between the receiver and each audio
Use an analog audio cable to connect the LINE 1/DVD
IN L/R or LINE 2 IN L/R jacks to the analog audio
output jacks on the connected component.
component.
When you connect aVCR, the video input from theVCR
should be sent to the TV directly.
Receiver
IN
L
connector
connector
R
Onkyo CD player,
etc.
L
R
AUDIO
OUT
Onkyo cassette
deck, etc.
connector
Connecting
Components
Remote Interactive
Dock, etc.
Remote control cable
If you connect other Onkyo components to the receiver
with the appropriate and audio cables, you can use
the following system functions. cables are special
cables solely for use with Onkyo products (no
are supplied with the receiver).
Notes:
• Push each plug in all the way to make a good
connection.
cables
• Use only dedicated
cables for
connections
(no
cables are supplied with the receiver).
•
jacks should be connected only to Onkyo
Auto Power On
components. Connecting them to another
manufacturer’s component may cause the receiver to
malfunction.
When you turn on the power or start playback on a
component that’s connected to the receiver, the receiver
will turn on automatically.And when you set the receiver
to Standby, all connected components will go on
Standby as well (the receiver’s POWER switch must be
set to ON for this to work).
• Some components may not support all
functions.
See the manuals supplied with your other Onkyo
components for more information.
Direct Change
When playback is started on an audio component
connected via
, the receiver will automatically select
that component as the input source.
Remote Control Operation
You can control all components in your system by using
the receiver’s remote controller. See pages 10-11 for
more information.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting the Power Cords of Other
Components
The receiver has AC outlets on its rear panel that can be
used to connect the power cords of other components
that you intend to use with the receiver. These
components can then be left turned on so that they turn
on and off as and when the receiver is turned on and set
to Standby.
e.g. European
models
e.g. North American
model
Caution:
• Make sure that the total capacity of the components
that you connect to theAC OUTLETS does not exceed
the stated capacity (e.g., TOTAL 120 W).
Notes:
• Onkyo components connected via
should be
connected directly to a wall outlet, not an AC
OUTLETS on the receiver.
• The number of AC OUTLETS, socket type, and total
capacity depends on the country in which you
purchased the receiver.
Connecting the Power Cord
• Connect the receiver’s power cord to a suitable wall
outlet.
Notes:
• Before connecting the power cord, connect all of
your speakers and AV components.
• Turning on the receiver may cause a momentary
power surge that might interfere with other electrical
equipment on the same circuit. If this is a problem,
plug the receiver into a different branch circuit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the Receiver
ON/STANDBY
STANDBY/ON
STANDBY indicator
Turning On and Standby
Changing the Input Display
You can change the input display name to “HDD”. When
the input display name has been changed “HDD” for
TAPE 1, the display name for the other button cannot be
changed to “HDD”.
After you changed the input display name, you can
operate the RI Dock using the remote controller supplied
with the receiver (see pages 10-11).
Press the [ON/STANDBY] button.
Alternatively, press the remote
controller’s [STANDBY/ON]
button.
The receiver comes on, the display
lights up, and the STANDBY indicator
1
Receiver
goes off.
or
Remote
controller
Press the appropriate input
selector button.
The selected input name appears in the
display.
1
To turn the receiver off, press the
[ON/STANDBY] button, or press the
remote controller’s [STANDBY/ON]
button. The receiver will enter Standby
mode. To prevent any loud surprises
when you next turn on the receiver,
always turn down the volume before
you turn it off.
Press and hold down the input
2
selector button selected in the
Step 1 above for approximately 3
seconds to change the display
name.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Audio Sources
INPUT
SELECTOR
Input selector buttons
SPEAKERS A/B
MASTER VOLUME
VOLUME
/
Press the input selector button
to select the component that you
want to listen to.
1
2
Receiver
Remote
controller
Use the [SPEAKERS A] and
[SPEAKERS B] buttons on the
receiver to select the speaker set
that you want to use.
Receiver
The A and B speaker indicators show
whether each speaker set is on or off.
Indicators
Start playback on the selected
component.
3
4
To adjust the volume, use the
receiver’s [MASTER VOLUME]
control, or the remote
Receiver
controller’s VOLUME [ ]/[
buttons.
]
Turn the control clockwise to turn up
the volume or counterclockwise to turn
down the volume.
Remote
controller
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Audio Sources—Continued
DIMMER
SLEEP
PHONES
DIMMER
(Other than European model)
MUTING
Muting the receiver
Setting the Display Brightness
(remote controller only)
You can adjust the brightness of the display.
You can temporarily mute the output of the receiver.
Press the remote controller’s
[DIMMER] button repeatedly to
select: dim, dimmer, or normal
brightness.
Alternatively, you can use the
1
Remote
controller
Press the remote controller’s
[MUTING] button.
1
The receiver is muted.
To unmute the receiver, press the
[MUTING] button again.
[DIMMER] button on the receiver
(other than European model).
Receiver
Note:
The Mute function will be cancelled if
the remote controller’s VOLUME
buttons are pressed or the receiver is set
to Standby.
Using the Sleep Timer
(remote controller only)
Using Headphones
With the sleep timer, you can set the receiver so that it
turns off automatically after a specified period.
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the receiver’s PHONES jack for private
listening.
Press the remote controller’s
[SLEEP] button repeatedly to
1
Remote
controller
select the required sleep time.
You can set the sleep time from 90 to 10
minutes in 10 minute steps.
The SLEEP indicator appears on the
display when the sleep timer has been set,
asshown.Thespecifiedsleeptimeappears
onthedisplayforabout5seconds, thenthe
previous display reappears.
Notes:
• Always turn down the volume before connecting your
headphones.
SLEEP indicator
• Sound output from speakers is not turned off even if
(when) the headphones plug is inserted in the
PHONES jack. To turn off or on the sound output from
speakers, use the SPEAKERS A and SPEAKERS B
buttons.
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
To check the remaining sleep time, press the [SLEEP]
button. Note that if you press the [SLEEP] button while
the sleep time is being displayed, you’ll shorten the sleep
time by 10 minutes.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Audio Sources—Continued
This section explains functions that can be used with any input source.
TREBLE
BASS
BALANCE
Using the Tone and Balance Controls
Adjusting the Bass
The BASS control adjusts bass
sounds. Turn it up to make them
louder. Turn it down to make them
quieter. Normally, it should be set
midway.
Adjusting the Treble
The TREBLE control adjusts treble
sounds. Turn it up to make them
louder. Turn it down to make them
quieter. Normally, it should be set
midway.
Adjusting the Balance
The BALANCE control is used to
control the relative volume level of
the left and right speaker systems or
headphones.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Unless you have the full consent of the copyright holder, copyright laws prohibit using your
recordings for anything other than personal enjoyment!
This section explains how to record the selected input source to a component with recording capability.
Input selector buttons
TAPE1 TAPE2 MONITOR
Recording the Input Source
You can record an audio signal on a recording
component connected to the TAPE 1 OUT or TAPE 2
OUT jacks.
When you record an audio signal on a recording
component connected to the TAPE 2 OUT jacks, you can
monitor the recorded sound. For details, refer to the
section “Monitoring the Recorded Sound” below.
When you want to record the input from the TAPE 2 IN
jacks, you cannot record the sound on a recording
component connected to the TAPE 1 OUT jacks.
Prepare the recorder:
• Set the recorder so that it’s ready for
recording.
1
• If necessary, adjust the recording level on the
recorder.
• See the recorder’s manual for more
information.
Use an input selector button other than
2
“TAPE 2 MONITOR” to select the
component that you want to record
from.
Start playback on the component
selected in step 1.
3
Note:
If you select another input source during
recording, the newly selected input source will
be recorded.
Note:
The volume, balance, mute and tone controls have no
effect on the signal being recorded.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording—Continued
Monitoring the Recorded Sound
When you record audio signal on a recording component
connected to the TAPE 2 OUT jacks, you can monitor
the recorded sound. The recorded sound monitoring
function allows you to compare the sounds by switching
the output between the sound before or after recording.
Pressing the TAPE 2 MONITOR
button indicates a sign
“T2 MONITOR OFF” on the
display. Press and hold the
button while the sign is
displayed, and release it when
the sign changes to
“T2 MONITOR ON.”
Then you will see a sign “> T-2 ON”
next to the input source name in the
display. However, only “>” is displayed
if a tuner is selected for input source.
Use the same procedures to deactivate
the sound monitoring function.
The signal flow in monitoring the recorded sound
Receiver
T2 MONITOR OFF
T2 MONITOR ON
TAPE 2
button
Amplifier
Input source
(CD, FM, etc.)
PLAY
REC
TAPE 2
The signal flow in monitoring the sound before
recording
Receiver
T2 MONITOR OFF
TAPE 2
button
Amplifier
Input source
(CD, FM, etc.)
PLAY
REC
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
DIRECT TUNING
TUNING DOWN/UP
Number buttons
Number
buttons
TUNING
/
CLR
DIRECT
TUNING
FM AM TUNING MODE
AM Frequency Step Setup
(not North America and Europe)
Press the [TUNING MODE]
button so that the AUTO indicator
appears or disappears from the
display.
2
Receiver
You must specify the AM frequency step used in your
area. Note that when this setting is changed, all radio
presets are deleted.
Auto Tuning
To activate this mode, press the
[TUNING MODE] button to turn on
the “AUTO” indicator. In this mode,
you will receive the broadcast in stereo
sound.
Use the receiver to perform the procedure below.
While pressing the [AM] button,
press the [TUNING MODE]
button.
1
Manual Tuning
Each press of the [TUNING MODE]
To activate this mode, press the
[TUNING MODE] button to turn off
the “AUTO” indicator. In this mode,
you will receive the broadcast in
monaural sound.
button switches the frequency step
setting between “10 kHz” and “9 kHz.”
and
Press the TUNING [ DOWN] or
[UP ] button.
3
Receiver
You can also use the remote
controller’s TUNING [ ]/[
buttons to tune the radio.
]
After the desired frequency step is
displayed, release the [AM] button.
Release
the button
Auto Tuning
Searching stops when a station is
found.
Listening to AM/FM Stations
Manual Tuning
The frequency stops changing when
you release the button.
With the built-in tuner, you can enjoy AM and FM radio
stations.
Use the [FM] or [AM] input
selector button to select AM or
FM.
Press the buttons repeatedly to change
the frequency one step at a time.
1
Receiver
In this example, FM has been selected.
Band
Frequency
(Actual display depends on country.)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by
entering the appropriate frequency.
Press the [MEMORY] button
again to store the station or
channel.
4
Receiver
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite AM/FM radio stations.
Press the [DIRECT TUNING]
1
Receiver
button.
Remote
controller
(Actual display depends on country.)
■ Selecting Presets
To select a preset, use the
1
Receiver
number buttons on the receiver,
or the remote controller’s
PRESET [ ]/[ ] buttons.
Within 8 seconds, use the
number buttons to enter the
2
Receiver
frequency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
Remote
controller
Remote
controller
■ Deleting Presets
Select the preset that you want to
delete.
See the previous section.
1
2
Presetting AM/FM Stations
While holding down the
[MEMORY] button, press the
[TUNING MODE] button.
The preset is deleted and its number
disappears from the display.
Receiver
Number buttons
PRESET
/
TUNING MODE
MEMORY
The North American model changes FM frequency in
0.2 MHz steps, 10 kHz steps for AM. For other models
the frequency changes in 0.05 MHz increments for FM
and 9 kHz (or 10 kHz) increments for AM.
You can store a combination of up to 40 of your favorite
AM/FM radio stations as presets.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator also appears.
Tune into the AM/FM station that
you want to store as a preset.
1
Press the [MEMORY] button.
The MEMORY indicator appears and
TUNED AUTO
2
Receiver
the preset number flashes.
FM STEREO
Tuning into Weak FM Stereo Stations
While the MEMORY indicator is
displayed (about 8 seconds), use
the number buttons on the
receiver to select a preset from 1
through 40.
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
3
Receiver
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
RDS Program Types (PTY)
Using RDS (European Models Only)
RDS only works with European models and only in
areas where RDS broadcasts are available.
When tuned into an RDS station, the RDS indicator
appears.
Type
Display
None
NONE
News reports
Current affairs
Information
Sport
NEWS
AFFAIRS
INFO
RDS indicator
SPORT
Education
EDUCATE
DRAMA
Drama
Culture
CULTURE
SCIENCE
VARIED
POP M
■ What is RDS?
Science and technology
Varied
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is
available in most European countries. Many FM stations
use it these days. In addition to displaying text
information, RDS can also help you find radio stations
by type (e.g., news, sport, rock, etc.).
Pop music
Rock music
Middle of the road music
Light classics
Serious classics
Other music
Weather
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
The receiver supports four types of RDS information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed.
Pressing the [DISPLAY] button will display the
frequency for 3 seconds.
Finance
Children’s programmes
Social affairs
Religion
RT (Radio Text)
Phone in
When tuned to an RDS station that’s broadcasting text
information, the text will be shown on the display (see
page 28).
Travel
Leisure
Jazz music
Country music
National music
Oldies music
Folk music
Documentary
Alarm test
PTY (Program Type)
This allows you to search for RDS radio stations by type
(see page 28).
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TEST
TP (Traffic Program)
This allows you to search for RDS radio stations that
broadcast traffic information (see page 28).
Notes:
• In some cases, the text characters displayed on the
receiver may not be identical to those broadcast by the
radio station. Also, unexpected characters may be
displayed when unsupported characters are received.
This is not a malfunction.
Alarm
ALARM
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Displaying Radio Text (RT)
To start the search, press
[SCAN].
The receiver searches until it finds a
station of the type you specified, at
which point it stops briefly before
continuing with the search.
4
5
When a station you want to listen
to is found, press [SCAN].
If no stations are found, the message
“Not Found” appears.
RT/PTY/TP
When tuned to an RDS station that’s broadcasting text
information, the text can be displayed.
Press the [RT/PTY/TP] button
once.
1
Listening to Traffic News (TP)
RT/PTY/TP
The RT information scrolls across the
display.
Notes:
• The message “Waiting” may appear while the receiver
waits for the RT information.
FM
SCAN
• If the message “No Text Data” appears on the display,
no RT information is available.
RT/PTY/TP
You can search for stations that broadcast traffic news.
Finding Stations by Type (PTY)
Use the [FM] input selector
button.
1
TUNING DOWN/UP
Press the [RT/PTY/TP] button
three times.
2
RT/PTY/TP
If the current radio station is
broadcasting TP (Traffic Program),
“[TP]” will appear on the display, and
traffic news will be heard as and when
it’s broadcast. If “TP” without square
brackets appears, this means that the
station is not broadcasting TP.
FM
SCAN
RT/PTY/TP
You can search for radio stations by type.
Use the [FM] input selector
1
button.
To locate a station that is
3
broadcasting TP, press [SCAN].
The receiver searches until it finds a
station that’s broadcasting TP.
If no stations are found, the message
“Not Found” appears.
Press the [RT/PTY/TP] button
twice.
2
RT/PTY/TP
The current program type appears on
the display.
Use the TUNING
3
[
DOWN]/[UP ] buttons to
select the type of program you
want.
See the table on page 27.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Naming Preset Channels (other than European model)
While receiving a preset FM orAM station, a maximum of 8 characters consisting of letters, numbers and some symbols
can be stored, for example to represent the station name.
You cannot assign a name to the RDS station (for European model).
Characters which can be entered:A B C D E F G H I J K L M N O P Q R S T U V W XY Z 1 2 3 4 5 6 7 8 9 0 – * /
Note: indicates a space.
Number buttons
TUNING DOWN/UP
CHARACTER
Note:
Entering a Name
Press the [DISPLAY] button when you wish to check the
frequency while you are entering the characters.
As an example, assume an FM station with a frequency
of 89.50 MHz has been stored in preset number 2 and
will be given the name “ONKYO.”
Correcting a Character
Select the desired preset
channel.
(Refer to “Selecting Presets” on
page 26.)
1
Select the desired station.
(Refer to “Selecting Presets” on page 26.)
1
2
Press the [CHARACTER] button.
The first character and the cursor flash
alternately.
Press the [CHARACTER] button
on the front panel.
2
Other than
European model
The frequency in the display goes off
and the cursor ( _ ) flashes.
Press theTUNING [ DOWN] or [UP
button to move the cursor below the
character that you wish to change.
The cursor moves to the right when the [UP
]
3
]
Continue pressing the [5MNO]
button until “O” is displayed.
button is pressed and moves to the left when the
DOWN] button is pressed.
3
Other than
European model
[
With each press of the button, the
Clearing all characters:
character that appears in the display
changes one at a time in the following
sequence: 5 → M → N → O → 5...
If a button is not pressed within one
second, the cursor automatically moves
to the next position.
Press [DIRECT TUNING] button.
Enter the desired character.
The previous character is replaced with a new
character.
4
5
Press the [CHARACTER] button.
Continue pressing number
4
buttons to enter the desired
characters.
To enter N, press the [5MNO] button.
To enter K, press the [4JKL] button.
To enter Y, press the [9YZ-] button.
Press the [CHARACTER] button
5
to store the entered characters.
If a button is not pressed within 16
seconds, the operation will end
automatically.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Components not Reached by the Remote
Controller Signals (IR IN/OUT)
In order to use the remote controller to control the
receiver from a remote location, you will need to
prepare a multiroom kit (sold separately) such as one
listed below:
Making Sensor Connections
When you place the IR receiver in the main room, connect
the cable from the connecting block to the IR IN terminal.
Make the connection as shown below. Do not plug any
equipment into the power outlet until all the connections
are complete.
• Multiroom A/V distribution and control system such
®
®
as those from Niles and Xantech
* Xantech is a registered trademark of Xantech Corporation.
* Niles is a registered trademark of Niles Audio Corporation.
from connecting block
If Remote Controller Signal Does not
Reach the Receiver Remote Sensor
Mini plug cable
Receiver
Effective Sensor Layout
Example for the main room
If the receiver is located inside a cabinet or other
enclosure where the infrared rays from the remote
controller cannot enter, then operation with the remote
controller will not be possible. In such a case, it will be
necessary to install a remote sensor at a location outside
of the cabinet so that the infrared rays from the controller
can be sensed.
If Remote Controller Signal Does not
Reach Other Components
Effective Sensor Layout
In this situation, you will need to use a commercially
available IR emitter. Connect the mini plug of the IR
emitter to the IR OUT terminal on the receiver and then
place the IR emitter on the remote sensor of the
component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is
output to the IR OUT terminal. The signal input from the
remote sensor on the front of the receiver will not be
output to the IR OUT terminal.
IR Receiver
Connecting
block
IR IN
Receiver
Remote controller
In the
Main room
cabinet
: Signal flow
IR Receiver
Connecting
block
IR IN
Example for the remote zone
The IR IN input allows you to control the receiver from
the remote zone with the remote controller even though
the remote zone may be on the other side of the building
from the main zone. The diagram below shows how to
make the proper connections for the remote zone.
Receiver
IR OUT
IR Emitter
Remote controller
To IR IN
Other
component
IR Receiver
: Signal flow
Receiver
Making Sensor Connections
Connecting
block
When you place the IR receiver in the main room, connect
the cable from the connecting block to the IR OUT terminal.
Other component
Remote controller
: Signal flow
Remote control
sensor
Main room
Remote Zone
: Signal flow
Mini plug
Emitter
IR Emitter
Receiver
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the receiver, look for a
solution in this section.
Audio
There’s no sound or it’s very quiet
• Make sure the speaker set A or B is on (page 20).
• Make sure that all audio connecting plugs are pushed
in all the way (pages 12-18).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with metal
part of each speaker terminal (page 12).
If you can’t resolve the issue yourself, try resetting
the receiver before contacting your Onkyo dealer.
To reset the receiver to its factory defaults, turn it
on and, while holding down the [LINE 2] button,
press the [ON/STANDBY] button.
“Clear”will appear on the display and the receiver
will enter Standby mode.
• Make sure that the speaker cables are not shorting.
• Make sure that the inputs and outputs of all compo-
nents are connected properly.
• Make sure that the correct input source is selected
(page 20).
• If the MUTING indicator is shown on the display,
press the remote controller’s [MUTING] button to
unmute the receiver (page 21).
Note that resetting the receiver will delete your radio
presets and custom settings.
• If your turntable doesn’t have a phono preamp built-
in, you must connect one between it and the receiver.
If your turntable uses an MC cartridge, you must con-
nect an MC head amp, or an MC transformer and a
phono preamp.
Power
Can’t turn on the receiver
• Make sure that the power cord is plugged into the wall
outlet properly.
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
The STANDBY indicator is flashing
The amp protection circuit has been activated. Remove
the power cord from the wall outlet immediately.
Disconnect all speaker cables and input sources, and
leave the receiver with its power cord disconnected for 1
hour. After that, reconnect the power cord and press the
[ON/STANDBY] button again. If you can not resolve
the problem, contact your Onkyo dealer.
• An audio cable may be picking up interference. Try
repositioning your cables.
Tuner
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the receiver away from your TV or computer.
• Listen to the station in mono (page 26).
• When listening to anAM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
Remote Controller
Others
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor-
rect polarity (page 5).
• Install new batteries. Don’t mix different types of bat-
teries or old and new batteries (page 5).
The
• To use
functions don’t work
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and receiver, even if they are connected digitally
(page 17).
• Make sure that the remote controller is not too far
away from the receiver, and that there’s no obstruction
between the remote controller and the receiver’s
remote control sensor (page 11).
• Make sure that the receiver is not subjected to direct
sunshine or inverter-type florescent lights. Relocate if
necessary (page 11).
The receiver contains a microcomputer for signal
processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup.In the
unlikely event that this happens, unplug the power cord
from the wall outlet, wait at least five seconds, and then
plug it back in again.
Can’t control other components
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
• If you’ve connected an
-capable Onkyo DS-A1
Remote Interactive Dock to the TAPE 1 jacks on the
receiver, for the remote controller to work properly,
you must set the input display to HDD (see page 19).
• If it’s an Onkyo component, make sure that the
cable and analog audio cable are connected properly.
Before disconnecting the power cord from the wall
outlet, set the receiver to Standby.
Connecting only an
cable won’t work (page 17).
• With some components, certain buttons may not work
as expected, and some may not work at all.
Memory Backup
• To control an Onkyo component that’s connected via
, point the remote controller at the receiver.
The receiver uses a battery-less memory backup
system in order to retain radio presets and other
settings when it’s unplugged or in the case of a power
failure. Although no batteries are required, the receiver
must be plugged into an AC outlet in order to charge the
backup system. Once it has been charged, the receiver
will retain the settings for several weeks, although this
depends on the environment and will be shorter in
humid climates.
Recording
Can’t record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the receiver,
input signals are not fed through to outputs with the
same name (e.g., TAPE IN to TAPE OUT).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Amplifier Section
General
Rated Output Power (FTC) (North American)
Power Supply
North American: AC 120 V, 60 Hz
European: AC 230-240 V, 50 Hz
Others: AC 230-240 V, 50Hz
North American: 2.1 A
European: 180 W
Others: 180 W
All channels:
50 watts minimum continuous power
per channel, 8 ohm loads, 2 channels
driven from 20 Hz to 20 kHz, with a
maximum total harmonic distortion of
0.08 %
Power Consumption
Rated Output Power (IEC) (European and Australian)
2 ch × 90 W at 4 ohms, 1 kHz, 1 ch driven
Maximum Output Power (JEITA) (Asian)
90 W at 4 ohms, 1 kHz, 2 ch driven
Standby Power
Consumption
North American: 0.2 W
Others: 0.3 W
Dimensions
(W × H × D)
Dynamic Power
North American:
435 × 149 × 340 mm
135 W + 135 W (2 Ω)
105 W + 105 W (4 Ω)
70 W + 70 W (8 Ω)
17-1/8"
7.5 kg
×
5-7/8"
×
13-3/8"
Weight
16.5 lbs.
European and Australian:
110 W + 110 W (2 Ω)
■ Audio Inputs
Analog Inputs
90 W + 90 W (4 Ω)
55 W + 55 W (8 Ω)
PHONO, CD, TAPE 1, TAPE 2, LINE 1,
LINE 2
THD (Total Harmonic
Distortion)
0.08 % (Power Rated)/ 0.08 % (1 kHz,
1 W)
■ Audio Outputs
Analog Outputs
Speaker Outputs
Damping Factor
Input Sensitivity and
Impedance
60 (Front, 1 kHz, 8 Ω)
TAPE 1, TAPE 2
SPEAKERS A
SPEAKERS B
1
150 mV/ 50 kΩ (LINE)
2.5 mV/ 50 kΩ (PHONO MM)
Phones
Output Level and
Impedance
Frequency Response
Tone Control
IR Input/Output
1/1
150 mV/ 2.2 kΩ (REC OUT)
10 Hz–100 kHz/ +1 dB–3 dB (CD)
±10 dB, 100 Hz (BASS)
±10 dB, 10 kHz (TREBLE)
100 dB (LINE, IHF-A)
80 dB (PHONO, IHF-A)
4 Ω–16 Ω
Specifications and features are subject to change without
notice.
Signal to Noise Ratio
Speaker Impedance
Tuner Section
■ FM
Tuning Frequency
Range
North American: 87.5 MHz– 107.9 MHz
Others: 87.5 MHz– 108.0 MHz
■ AM
Tuning Frequency
Range
North American: 530 kHz–1710 kHz
Others: 522 kHz–1611 kHz
Preset Channel
40
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
34
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
D0805-1
SN 29344818
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 8 1 8 *
Download from Www.Somanuals.com. All Manuals Search And Download.
|