Contents
7.1ch Home Theater System
Connection .................................... 20
Turning On & First Time Setup..... 41
HT-S6100
AV Receiver (HT-R667)
Speaker Package (HTP-750X)
Front Speakers (SKF-750XF L/R)
Center Speaker (SKC-750XC)
Surround Speakers (SKM-750XS L/R)
Surround Back Speakers (SKB-750X L/R)
Subwoofer (SKW-750X)
Basic Operation
Dock for iPod (DS-A1L)
Playing your AV components....... 50
Using the Tuner............................ 54
DS-A1L Dock for the iPod............ 57
Instruction Manual
Enjoying the Listening Modes ..... 59
Thank you for purchasing an Onkyo 7.1ch Home
Theater System. Please read this manual thoroughly
before making connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new 7.1ch Home Theater Sys-
tem.
Please retain this manual for future reference.
Troubleshooting............................ 92
Specifications................................ 96
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
For U.S. models
FCC Information for User
CAUTION:
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
The user changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Pressing the [ON/STANDBY] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
•
Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
Pour le Modèle Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME
NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Precautions
Precautions—Continued
Placement
For British models
• The subwoofer cabinet is made out of wood and is
therefore sensitive to extreme temperatures and
humidity, do not put it in locations subject to direct
sunlight or in humid places, such as near an air condi-
tioner, humidifier, bathroom, or kitchen.
• Do not put water or other liquids close to the speakers.
If liquid is spilled over the speakers, the drive units
may be damaged.
• Speakers should only be placed on sturdy, flat surfaces
that are free from vibration. Putting them on uneven or
unstable surfaces, where they may fall and cause dam-
age, will affect the sound quality.
• Subwoofer is designed to be used in the upright verti-
cal position only. Do not use it in the horizontal or
tilted position.
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
• If the unit is used near a turntable, CD player or DVD
player, howling or slipping of sound may occur. To
prevent this, move the unit away from the turntable,
CD player or DVD player, otherwise lower the unit’s
output level.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must be
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
Using Close to a TV or Computer
TVs and computer monitors are magnetically sensitive
devices and as such are likely to suffer discoloration or
picture distortion when conventional speakers are
placed nearby. To prevent this, the SKF-750XF and
SKC-750XC feature internal magnetic shielding. In
some situations, however, discoloration may still be an
issue, in which case you should turn off your TV or
monitor, wait 15 to 30 minutes, and then turn it back on
again. This normally activates the degaussing function,
which neutralizes the magnetic field, thereby removing
any discoloration effects. If discoloration problems per-
sist, try moving the speakers away from your TV or
monitor. Note that discoloration can also be caused by a
magnet or demagnetizing tool that’s too close to your
TV or monitor.
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
Do not place SKM-750XS close to TV or a computer
monitor because they have no magnetic shield.
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
Input Signal Warning
GROEBENZELL, GERMANY
The speakers can handle the specified input power when
used for normal music reproduction. If any of the fol-
lowing signals are fed to them, even if the input power is
within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1. Interstation noise from an untuned FM radio.
2. Sound from fast-forwarding a cassette tape.
3. High-pitched sounds generated by an oscillator,
electronic musical instrument, and so on.
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
4. Amplifier oscillation.
5. Special test tones from audio test CDs and so on.
6. Thumps and clicks caused by connecting or discon-
necting audio cables (Always turn off your amplifier
before connecting or disconnecting cables.)
7. Microphone feedback.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
Make sure you have the following items:
AV Receiver HT-R667
Speaker Package HTP-750X
Front speakers
(SKF-750XF L/R)
HT-R667
Center speaker
(SKC-750XC)
Remote controller and two batteries (AA/R6)
Surround speakers
(SKM-750XS L/R)
Speaker setup microphone
Indoor FM antenna
Surround back
speakers
(SKB-750X L/R)
Subwoofer (SKW-750X)
AM loop antenna
(Red)
(White)
(Green)
Speaker cable for front speakers 11 ft. and
center speaker 10 ft.
(Blue)
(Gray)
(Brown)
(Tan)
Speaker cables for surround and surround back
speakers 30 ft.
RCA cable for subwoofer connection 10 ft.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents—Continued
4 floor pads for the subwoofer
Rubber spacers [28] (For the speakers)
Base for horizontal mounting (For the center
speaker)
Dock for iPod DS-A1L
*
In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operation are the same
regardless of color.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Two Sets of Speakers
Speaker Sets A and B
You can use two sets of speakers with the AV receiver: speaker set A and speaker set B.
Speaker set A should be used in your main listening room for up to 7.1-channel playback.
*While speaker set B is on, speaker set A is reduced to 5.1-channel playback.
Speaker set B can be used in another room and offers 2-channel stereo playback.
*Only analog input sources are output by speaker set B.
I
ON/STANDBY
A
SPEAKERS
B
STANDBY
or
DOCK
MULTI CH
DVD
VCR/DVR
CBL/S
PHONES
A
SPEAKERS
B
TONE
/
Speaker set A
Speaker set B
Indicator
Output
Set A: 5.1 channels
Set B: 2 channels
On
A
A
B
B
On
Off
On
Off
Set A: 7.1 channels
Set B: 2 channels
No sound
Off
Main Room (speaker set A)
Center speaker
Front left
speaker
Front right
speaker
Subwoofer
Sub Room (speaker set B)
Surround
left
Surround
right
speaker
speaker
Surround back
left speaker
Surround back
right speaker
* Digital input sources are not output
by speaker set B. Connect your
source component with an analog
connection.
* While speaker set B is on, the surround
back speakers output no sound.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Amplifier
Speaker Package HTP-750X
• 130 Watts/Channel @ 8 ohms (FTC)
• WRAT-Wide Range Amplifier Technology
(5Hz–100kHz bandwidth)
SKF-750XF L/R 2-Way Front Speakers
SKC-750XC Center Speaker
• 3-1/8 inch cone woofer ×2
• Optimum Gain Volume Circuitry
• 1 inch Balanced dome tweeter
• Max. input power:110 W
Processing
• Magnetically shielded
• HDMI Video Upscaling (Up to 1080i)
• HDMI Video Upconversion
• 8-ohm impedance
*1
• Color-coded speaker terminals and speaker cable
• Dolby TrueHD
• DTS-HD Master Audio
*2
SKM-750XS L/R Full-Range Surround Speakers
SKB-750X L/R Full-Range Surround Back Speakers
• 3-1/8 inch full-range speaker
• Faroudja DCDi Edge Enhancement
• Direct Mode
*3
• Music Optimizer for Compressed Music
• Max. input power:110 W
• CinemaFILTER
• Non-Scaling Configuration
• A-Form Listening Mode Memory
• 24-bit/192kHz D/A Converters
• Powerful and Highly Accurate 32-bit DSP Processing
• 8-ohm impedance
• Color-coded speaker terminals and speaker cable
SKW-750X Bass Reflex Powered Subwoofer
• 10 inch cone woofer
• Max. power:290 W
Connections
*4
• 4 HDMI Inputs and 1 Output
*5
Dock DS-A1L
• Onkyo RIHD for System Control
• HDTV-Ready Component Video Switching (2 Inputs/
1 Output)
• 4 Digital Inputs (2 Optical/2 Coaxial/4 Assignable)
• 3 S-Video Inputs/2 Outputs
• Color-Coded 7.1 Multichannel Inputs
• Subwoofer Pre Outs
• Play your iPod music through your Onkyo audio sys-
tem and enjoy great sound
• Control your iPod with your Onkyo remote controller
• Supports all iPod models with an iPod connector,
except 3rd Generation iPod models
• Charges your iPod’s battery while you enjoy your
music
• Dedicated DOCK jack for quick and simple DS-A1L
Dock connection and iPod playback
Miscellaneous
*1.
• 40 AM/FM Presets
®*6
• Audyssey 2EQ
ibration
Room Correction and Speaker Cal-
Manufactured under license from Dolby Laboratories. Dolby,
Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
®*6
• Audyssey Dynamic EQ
Loudness Correction
• Crossover Adjustment (40/50/60/80/100/120/150/
200Hz)
*2.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 &
other U.S. and worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol, DTS-HD and
DTS-HD Master Audio are trademarks of DTS, Inc.
• A/V Sync Control Function (up to 100 ms)
• Theater Dimensional Virtual Surround Function
• On-Screen Display
*7
• Preprogrammed
-Compatible Remote
“DTS” and “DTS-ES | Neo: 6” are registered trademarks of
DTS, Inc. “96/24” is a trademark of DTS, Inc.
*3 Music Optimizer™ is a trademark of Onkyo Corporation.
*4
HDMI, the HDMI logo and High Definition Multimedia Inter-
face are trademarks or registered trademarks of HDMI Licens-
ing, LLC.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Features—Continued
*5
RIHD is a trademark of Onkyo Corporation.
*6
Manufactured under license fromAudyssey Laboratories. U.S.
and foreign patents pending. Audyssey 2EQ and Dynamic EQ
are trademarks of Audyssey Laboratories.
*7
Theater-Dimensional is a trademark of Onkyo Corporation.
* iPod is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
*
“x.v.Color” is a trademark of Sony Corporation.
This product incorporates copyright protection tech-
nology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by Macro-
vision Corporation, and is intended for home and
other limited consumer uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Precautions ........................................ 4
Package Contents ............................................ 5
Dock for iPod DS-A1L ........................................... 6
Using Two Sets of Speakers ........................... 7
Sub Room (speaker set B) ....................................... 7
Dock DS-A1L ......................................................... 8
Getting to Know the AV Receiver ................. 12
Front Panel ............................................................ 12
Rear Panel ............................................................. 14
Compatible iPod models .......................................57
Source Format ....................................................60
Connecting the AM Loop Antenna ...................... 24
Connecting a TV or Projector ............................... 29
Connecting a VCR or DVR for Recording ........... 33
Connecting a Satellite, Cable, or Terrestrial
Source Setup .........................................................79
Miscellaneous Setup .............................................80
Hardware Setup .....................................................81
Lock Setup ............................................................83
Set-top box or Other Video Source .................... 34
Connecting Components with HDMI ................... 35
Making HDMI Connections ................................. 36
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Remote Control Codes ...........................84
Controlling a DVD Player, or DVD Recorder ......86
Controlling a CD Player, CD Recorder,
7.1ch Home Theater Speaker Package ..................97
Dock DS-A1L .......................................................97
Video Resolution Chart ..................................98
Onscreen Setup Menu Map ............................99
* To reset the AV receiver to its factory defaults, turn
it on and, while holding down the [VCR/DVR] but-
ton, press the [ON/STANDBY] button (see
page 92).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the AV Receiver
Front Panel
1 2 3
4
5
6
7 8 9
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
SETUP MIC
VIDEO
L
AUDIO
R
PHONES
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
J
K
L
MNO PQ RST U
V
The actual front panel has various logos printed on it. They are not shown here for clarity.
The page numbers in parentheses show where you can find the main explanation for each item.
A ON/STANDBY button (41)
I MASTER VOLUME control (50)
Sets the AV receiver to On or Standby.
Sets the volume of the AV receiver to Min, 1
through 79, or Max.
B STANDBY indicator (41)
J PHONES jack (52)
Lights up when the AV receiver is on Standby and
flashes while a signal is being received from the
remote controller.
dard pair of stereo headphones for private listening.
K SPEAKERS A B buttons
C Input selector buttons (50)
Select the following input sources: DVD,
VCR/DVR, CBL/SAT, AUX, TAPE, TUNER, CD,
DOCK.
Turn speaker set A and B on or off.
L TONE, –, and + buttons (71)
The [MULTI CH] button selects the multichannel
DVD input.
M MOVIE/TV button (59)
Selects the listening modes intended for use with
movies and TV.
D Remote-control sensor (17)
Receives control signals from the remote controller.
N MUSIC button (59)
Selects the listening modes intended for use with
music.
E Display
See “Display” on page 13.
O GAME button (59)
F SETUP button
Selects the listening modes intended for use with
video games.
Opens and closes the setup menus.
P DISPLAY button (52)
buttons
Displays various information about the currently
selected input source.
When AM or FM is selected, the TUNING [
]
[
] buttons are used for radio tuning, and the PRE-
Q DIGITAL INPUT button (49)
SET [ ] [ ] buttons are used to select radio pre-
sets (see page 56). With the setup menus, they work
as arrow buttons and are used to select and set
items. The ENTER button is also used with the
setup menus.
Used to assign digital inputs to input selectors.
R DIMMER button (51)
Adjusts the display brightness.
S MEMORY button (56)
Used when storing or deleting radio presets.
H RETURN button
Selects the previously displayed setup menu.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
T TUNING MODE button (54)
Selects the Auto or Manual tuning mode for AM
and FM radio.
V AUX INPUT (37, 68)
Used to connect a camcorder, game console, and so
on. There are input jacks for composite video and
analog audio.
U SETUP MIC (42)
The automatic speaker setup microphone connects
here.
Display
1 2
3
4
5 6 7
8
1A and B speaker indicators (7, 50)
Indicator A lights up when speaker set A is on. Indi-
cator B lights up when speaker set B is on.
2MUTING indicator (51)
Flashes while the AV receiver is muted.
Show the selected listening mode and audio input
signal format.
4Tuning indicators (54)
FM STEREO (54): Lights up when tuned to a ste-
reo FM station.
selected for AM or FM radio. Goes off when Man-
ual Tuning mode is selected.
TUNED (54): Lights up when tuned to a radio sta-
tion.
5SLEEP indicator (51)
Lights up when the Sleep function has been set.
6Message area
Displays various information.
7Audio input indicators
Indicate the type of audio input that’s selected as the
audio source: MULTI CH, or HDMI.
8Audyssey indicator
Lights up during automatic speaker setup.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the AV Receiver—Continued
Rear Panel
1 2 3 4 5 6
8
9
7
HDMI
ASSIGNABLE
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
SURR SPEAKERS
FRONT SPEAKERS A
SURR BACK SPEAKERS
L
L
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
AM
(DVD)
MONITOR
OUT
CENTER SPEAKER
COAXIAL
VCR/DVR
CBL/SAT
DVD
CB/PB
2
R
R
V
S
V
(CBL/SAT)
ANTENNA
CR/PR
FM
75
1
S
(VCR/DVR)
OPTICAL
OUT
OUT
IN
2
(CBL/SAT) IN 1(DVD)
ASSIGNABLE
IN
IN
IN
IN
IN
OUT
OUT
2
(CD)
PRE OUT
IN
IN
FRONT
SURR
CENTER SURR BACK
L
ASSIGNABLE
SUB
WOOFER
L
L
L
R
R
R
R
REMOTE
SUB
CONTROL
WOOFER
FRONT SPEAKERS B
DVD
CD
TAPE
CBL/SAT
VCR/DVR
J
K L
M NO
P
Q
R
A DIGITAL IN OPTICAL 1 and 2
components with an optical digital audio output,
This jack is for connecting the supplied DS-A1L
Dock.
such as a CD player or DVD player. They’re assign-
able, which means you can assign each one to an
input selector to suit your setup. See “Digital Input
Setup” on page 47.
G MONITOR OUT
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
H AM and FM ANTENNA
B DIGITAL IN COAXIAL 1 and 2
The AM push terminals are for connecting an AM
antenna. The FM jack is for connecting an FM
antenna.
ing components with a coaxial digital audio output,
such as a CD player or DVD player. They’re assign-
able, which means you can assign each one to an
input selector to suit your setup. See “Digital Input
Setup” on page 47.
I FRONT L/R, CENTER, SURR L/R, and SURR
BACK L/R SPEAKERS
These terminal posts are for connecting the front
speakers, center, surround, and surround back
speakers.
C COMPONENT VIDEO IN 1 and 2
such as a DVD player, DVD recorder, or DVR (dig-
ital video recorder). They’re assignable, which
means you can assign each one to an input selector
to suit your setup. See “Component Video Input
Setup” on page 47.
J
REMOTE CONTROL
This
(Remote Interactive) jack can be con-
nected to the
Onkyo component for remote and system control.
jack on another
-capable
To use , you must make an analog audio connec-
tion (RCA) between the AV receiver and the other
component, even if they are connected digitally.
D COMPONENT VIDEO OUT
This RCA component video output is for connect-
ing a TV or projector with a component video input.
K CD IN
This analog audio input is for connecting a CD
E HDMI IN 1–4 and OUT
player’s analog audio output.
HDMI (High Definition Multimedia Interface) con-
nections carry digital audio and digital video.
L TAPE IN/OUT
connecting a recorder with an analog audio input
and output, such as a cassette deck, MD recorder,
etc.
with an HDMI output, such as a DVD player, DVD
recorder, or DVR (digital video recorder). They’re
assignable, which means you can assign each one to
an input selector to suit your setup. See “HDMI
Input Setup” on page 46.
The HDMI outputs are for connecting a TV or pro-
jector with an HDMI input.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the AV Receiver—Continued
M CBL/SAT IN
A cable or satellite receiver can be connected here.
There are S-Video and composite video input jacks
for connecting the video signal, and there are analog
audio input jacks for connecting the audio signal.
N VCR/DVR IN/OUT
A video component, such as a VCR or DVR, can be
connected here for recording and playback. There
are S-Video and composite video input and output
jacks for connecting the video signal, and there are
analog audio input jacks for connecting the audio
signal.
O DVD IN
This input is for connecting a DVD player. There
are S-Video and composite video input jacks for
connecting the video signal.
P DVD FRONT L/R, CENTER, SUBWOOFER,
SURR L/R, and SURR BACK L/R
This analog multichannel input is for connecting a
component with a 5.1/7.1-channel analog audio out-
put, such as a DVD player, DVD-Audio or
SACD-capable player, or an MPEG decoder.
Q SUBWOOFER PRE OUT
This analog audio output can be connected to a
powered subwoofer.
R FRONT SPEAKERS B
These push terminals are for connecting speaker
set B.
See pages 20–40 for hookup information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Package
Subwoofer (SKW-750X)
For detailed information, see the pages in parentheses.
A STANDBY/ON indicator
■ Front
Red:
Subwoofer in standby mode
Blue: Subwoofer on
With the Auto Standby function, the SKW-750X
automatically turns on when an input signal is
detected in Standby mode. When there’s no input
enters Standby mode.
B OUTPUT LEVEL control (50)
This control is used to adjust the volume of the sub-
woofer.
1
C LINE INPUT (22)
This RCA input should be connected to the sub-
woofer pre out on your AV receiver, amp, or other
receiver with supplied RCA cable.
■ Rear
Note:
TheAuto Standby function turns the subwoofer on when
the input signal exceeds a certain level. If the Auto
Standby function does not work reliably, try slightly
increasing or decreasing the subwoofer output level on
the AV receiver (page 81).
X
2
3
To AC outlet
SKM-750XS, SKB-750X)
1Keyhole slots
■ Rear
These keyhole slots can be used to wall-mount the
speaker. See page 23 for mounting instructions.
SKF-750XF/SKM-750XS/SKC-750XC/SKB-750X
2Speaker terminals
These push terminals are for connecting the speaker
to your AV Receiver, amp, or other receiver with the
supplied speaker cables. The supplied speaker
cables are color-coded for easy identification. Sim-
ply connect each cable to the same-colored positive
speaker terminal.
1
3Speaker mount/bracket inserts
These threaded inserts can be used to attach the
speaker either horizontally or vertically to a speaker
mount or bracket.
3
2
Note:
Use commercially available 1/4" screws to attach
the speaker to a speaker mount or bracket.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller
Installing the Batteries
Using the Remote Controller
When using the remote controller, point it toward the AV
receiver’s remote control sensor, as shown below.
To open the battery compartment, press
the small lever and remove the cover.
1
Remote control sensor
STANDBY indicator
AV receiver
30˚
30˚
Insert the two supplied batteries (AA/R6)
in accordance with the polarity diagram
inside the battery compartment.
2
Approx. 16 ft.
Notes:
• The remote controller may not work reliably if the AV
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the AV receiver is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
• Don’t put anything on top of the remote controller,
such as a book or magazine, because a button may be
pressed continuously, thereby draining the batteries.
• The remote controller may not work reliably if the AV
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
Replace the cover and push it shut.
3
• The remote controller will not work if there’s an obsta-
cle between it and the AV receiver’s remote control
sensor.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
Controlling the AV Receiver
■ Controlling the receiver
C MULTI CH button (50)
Selects the multichannel DVD input.
REMOTE MODE button to select Receiver mode
first.
D SP A/B button (50)
Used to turn speaker set A or B on or off.
You can also use the remote controller to control
your DVD player, CD player, and other components.
See page 84 for more details.
Used to select and adjust settings.
F SETUP button
Used to change settings.
Used to select the listening modes.
H DIMMER button (51)
94
A
Adjusts the display brightness.
I DISPLAY button (52)
TUNER
2
3
Displays information about the current input source.
J MUTING button (51)
J
K
5
Mutes or unmutes the AV receiver.
RECEIVER
K VOL [ ]/[ ] button (50)
Adjusts the volume of the AV receiver regardless of
4
15
L RETURN button
Returns to the previous display when changing set-
tings.
6
L
M
M AUDIO button (71)
Used to change audio settings.
When the Audio TV Out setting is set to On
(page 82), this button is disabled.
N SLEEP button (51)
Used with the Sleep function.
7
■ Controlling the tuner
To control the AV receiver’s tuner, press the [TUNER]
(or [RECEIVER]) REMOTE MODE button. You can
select AM or FM by pressing the [TUNER] button
repeatedly.
2
N
38
1Arrow [ ]/[ ]/[ ]/[ ] buttons
2Number buttons (55)
Used to select AM and FM radio stations and preset
stations directly.
3D.TUN button (55)
For detailed information, see the pages in parentheses.
4DISPLAY button(55)
Displays information about the band, frequency,
preset number, and so on.
A ON/STANDBY button (41)
Sets the AV receiver to On or Standby.
5CH +/– button (56)
B REMOTE MODE/INPUT SELECTOR buttons
(19, 50, 86–91)
Selects radio presets.
Note:
Selects the remote controller modes and the input
sources.
• An Onkyo cassette recorder connected via
also be controlled in Receiver (see page 90).
can
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controller—Continued
To control your iPod when it’s seated in the supplied
DOCK jack, press the [DOCK] REMOTE MODE but-
ton.
See page 37 for details on connecting the DS-A1L Dock.
To control an RI Dock other than the DS-A1L, see “Con-
trolling Other Components” on page 84.
] button
Restarts the current song. Press it twice to select the
previous song.
D Rewind [ ] button
Press and hold to rewind.
E Pause [ ] button
Pauses playback.
F REPEAT button
Used with the repeat function.
7
A
G DISPLAY button
Turns on the backlight for 30 seconds.
H MUTING button (51)
8
9
Mutes or unmutes the AV receiver.
DOCK
I ALBUM +/– button
Selects the next or previous album.
J
K
J VOL [ ]/[ ] button (50)
Adjusts the volume of the AV receiver.
L
K MENU button
Displays a menu.
2
3
L PLAYLIST [ ]/[ ] buttons
M
N
Selects the previous or next playlist on the iPod.
M Play [ ] button
Starts playback. If the component is off, it will turn
on automatically.
O
P
4
5
6
N Next [
] button
Selects the next song.
Q
R
O Fast Forward [ ] button
Press and hold to fast forward.
P Stop [ ] button
Stops playback and displays a menu.
*
With some components, certain buttons may not
work as expected, and some may not work at all.
Q PLAY MODE button
Selects play modes on components with selectable
play modes.
R RANDOM button
A ON/STANDBY button
Used with the shuffle function.
Turns the iPod on or off.
Notes:
• Your iPod may not respond the first time you
press this button, in which case you should press
it again. This is because the remote controller
transmits the On and Standby commands alter-
nately, so if your iPod is already on, it will remain
on when the remote controller transmits an On
command. Similarly, if your iPod is already off, it
will remain off when the remote controller trans-
mits an Off command.
B Arrow [ ]/[ ] and ENTER buttons
Used to navigate menus and select items.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers
Enjoying Home Theater
Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your
own home—just like being in a movie theater or concert hall. You can enjoy DVDs featuring Dolby Digital or DTS.
With analog or digital TV, you can enjoy Dolby Pro Logic IIx, DTS Neo:6, or Onkyo’s original DSP listening modes.
Surround left and right speakers
(SKM-750XS)
These speakers are used for precise
sound positioning and to add realistic
ambience.
Front left and right speakers (SKF-750XF)
These output the main sound.Their role in a home theater is to provide a solid
anchor for the sound image. They should be positioned facing the listener at
about ear level, and equally spaced from the TV. Angle them inward slightly so
as to create a triangle, with the listener at the apex.
Position them at the sides of the lis-
tener, or slightly behind, about 2–3 feet
(60–100 cm) above ear level. Ideally
they should be equally spaced from the
listener.
Center speaker (SKC-750XC)
This speaker enhances the front left
and right speakers, making sound
movements distinct and providing a
full sound image. For movies it’s used
mainly for dialog.
Position it close to yourTV (preferably
on top) facing forward at about ear
level, or at the same height as the
front left and right speakers.
Subwoofer (SKW-750X)
The subwoofer handles the bass sounds of
the LFE (Low-Frequency Effects) channel.
The volume and quality of the bass output
from your subwoofer will depend on its posi-
tion, the shape of your listening room, and
your listening position.In general, a good bass
sound can be obtained by installing the sub-
woofer in a front corner, or at one-third the way
along the front wall, as shown.
Surround back left and right speakers (SKB-750X)
These speakers are necessary to enjoy Dolby Digital
EX, DTS-ES Matrix, DTS-ES Discrete, etc. They
enhance the realism of surround sound and improve
sound localization behind the listener. Position them
behind the listener about 2–3 feet (60–100 cm) above
ear level.
Tip: To find the best position for your sub-
woofer, while playing a movie or some music
with good bass, experiment by placing your
subwoofer at various positions within the room
and choose the one that provides the most
satisfying results.
Corner
position
1/3 of wall
position
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers—Continued
Speaker Configuration
Speaker Connection Precautions
For 7.1-channel surround-sound playback, you need
seven speakers and a powered subwoofer.
Read the following before connecting your speakers:
• You can connect speakers with an impedance of
between 8 and 16 ohms. If you use speakers with a
lower impedance, and use the amplifier at high volume
levels for a long period of time, the built-in amp pro-
tection circuit may be activated.
The following table shows which channels you should
use based on the number of speakers you have.
Number of speakers:
Front left
2
3
4
5
6
7
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
• Disconnect the power cord from the wall outlet before
making any connections.
Front right
• Read the instructions supplied with your speakers.
Center
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals to only positive (+) terminals,
and negative (–) terminals to only negative (–) termi-
nals. If you get them the wrong way around, the sound
will be out of phase and will sound unnatural.
Surround left
✓
✓
Surround right
Surround back*
Surround back left
Surround back right
✓
✓
• Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
* If you’re using only one surround back speaker, connect it to the
SURR BACK L terminals.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver.
No matter how many speakers you use, a powered sub-
woofer is recommended for a powerful and solid bass.
• Don’t connect more than one
cable to each speaker termi-
nal. Doing so may damage the
AV receiver.
To get the best from your surround-sound system, you
must set the speaker settings. You can do this automati-
cally (see page 42) or manually (see page 74).
• Don’t connect a speaker to several terminals.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers—Continued
Connecting Speaker Set A
Connecting Speaker Set B
Strip 5/8" of insulation
Strip 3/8" of insulation
5/8"
3/8"
1
1
from the ends of the
speaker cables, and twist
the bare wires tightly, as
shown.
from the ends of the
speaker cables, and twist
the bare wires tightly, as
shown.
Unscrew the terminal. Fully insert the bare wire,
making sure that it’s touching the threaded shaft
in the center. Screw the terminal tight.
While pressing the lever, insert
the wire into the hole, and then
release the lever.
2
2
Make sure that the terminals are
gripping the bare wires, not the
insulation.
Note:
While speaker set B is on, speaker set A is reduced to
5.1-channel playback.
Speaker Set A
Front right
speaker
Front left
speaker
Center
speaker
The following illustration shows which speaker should be
connected to each pair of terminals.
If you’re using only one surround back speaker, connect it
to the left (L) SURR BACK SPEAKERS terminals.
HDMI
ASSIGNABLE
DVR)
IN
1
(DVD)
OUT
SURR BACK SPEAKERS
SURR SPEAKERS
FRONT SPEAKERS
A
L
L
ON
AM
DOCK
(for DS-A1L)
MONITOR
OUT
CENTER SPEAKER
CBL/SAT
VCR/DVR
DVD
R
R
V
V
S
ANTENNA
FM
75
S
FRONT SPEAKERS
A
SURR BACK SPEAKERS
N
SURR SPEAKERS
IN
IN
IN
IN
IN
OUT
OUT
S
PRE OUT
FRONT
SURR
CENTER SURR BACK
L
SUB
L
L
WOOFER
L
L
R
R
R
CENTER
SPEAKER
SUB
WOOFER
FRONT SPEAKERS
B
CBL/SAT
VCR/DVR
DVD
R
R
Front right
speaker
Front left
speaker
Surround
back right
speaker
Surround
back left
speaker
Surround
right
speaker
Surround
left
speaker
Powered
subwoofer
Speaker Set B
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Speakers—Continued
Center Speaker Base
Wall Mounting
The center speaker base is for mounting the center
speaker horizontally. If you put it on a TV stand or AV
stand, aim it toward the listening position. The center
speaker should sit securely on the base. If it’s loose, try
resetting it.
The speakers can easily be wall mounted by using the
keyhole slots. To prevent the speaker from vibrating
against the wall, attach four of the supplied spacers to the
keyhole fins on the rear of each speaker.
■ Mounting vertically
The cradle surface of the base features two stoppers to
prevent the speaker from moving. Therefore, you can tilt
the speaker toward the front by up to 11 degrees.
To mount the front speakers vertically, use the keyhole
slot shown to hang each speaker on a screw that’s
securely screwed into the wall.
SKC-750XC
Rubber spacers
11
Stoppers
Keyhole slot for
vertical wall
mounting
Baseforhorizontal
mounting
■ Using the included rubber spacers
We recommend using the supplied rubber spacers to
achieve the best possible sound from your speakers. The
rubber spacers prevent the speakers from moving, pro-
viding a more stable setup.
■ Mounting horizontally
To mount the center speaker horizontally, use the two
keyhole slots shown to hang each speaker on two screws
that are securely screwed into the wall.
Rubber spacers
Keyhole slots for horizontal
wall mounting
Front
Bottom of
the base
Rubber
spacers
Rubber spacers
Caution:
A mounting screw’s ability to support a speaker depends
on how well it’s anchored to the wall. If you have hollow
walls, screw each mounting screw into a stud. If there are
no studs, or the walls are solid, use suitable wall anchors.
Bottom of
the speaker
Use screws with a head diameter of 3/8" or less and a
shank diameter of 1/8" or less. With hollow walls, use a
cable/pipe detector to check for any power cables or
water pipes before making any holes.
Using the Floor Pads for Subwoofer
Leave a gap of between 1/4"
If the subwoofer is placed on a hard floor (wood, vinyl,
tile, etc.) and playback is very loud, the subwoofer's feet
may damage the flooring.
To prevent this, place the sup-
plied pads underneath the sub-
woofer's feet. The pads also
Wall
and 5/16" between the wall
and the base of the screw
head, as shown.
(We recommend that you con-
sult a home installation pro-
1/4" – 5/16"
provide a stable base for the
fessional.)
subwoofer.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
The AV receiver won’t pick up any radio signals without
any antenna connected, so you must connect the antenna
to use the tuner.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
AM antenna push terminals
AM
ANTENNA
FM
75
FM antenna jack
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
2
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Attach the FM antenna, as shown.
1
■ American Model
FM
75
Insert the plug fully
into the jack.
Push
Insert wire
Release
Once your AV receiver is ready for use, you’ll
need to tune into an FM radio station and adjust
the position of the FM antenna to achieve the best
possible reception.
AM
ANTENNA
Use thumbtacks or something similar to
fix the FM antenna into position.
Once your AV receiver is ready for use, you’ll
need to tune into an AM radio station and adjust
the position of theAM antenna to achieve the best
possible reception.
2
Keep the antenna as far away as possible from
cords.
Thumbtacks, etc.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 25).
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 25).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoorAM antenna can be used in
addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
FM
75
AM
ANTENNA
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
OutdoorAM antennas work best when installed horizon-
tally outside, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To AV receiver
To TV (or VCR)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components
AV Connection Color Coding
About AV Connections
RCA-type AV connections are usually color coded: red,
white, and yellow. Use red plugs to connect right-
channel audio inputs and outputs (typically labeled “R”).
Use white plugs to connect left-channel audio inputs and
outputs (typically labeled “L”). And use yellow plugs to
connect composite video inputs and outputs.
• Before making any AV connections, read the manuals
supplied with your other AV components.
• Don’t connect the power cord until you’ve completed
and double-checked all AV connections.
Optical Digital Jacks
Analog audio
Left (white)
Right (red)
Left (white)
Right (red)
The AV receiver’s optical digital jacks have shutter-type
covers that open when an optical plug is inserted and
close when it’s removed. Push plugs in all the way.
Composite video
(Yellow)
(Yellow)
Right!
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
•
Push plugs in all the way to make
good connections (loose connections
can cause noise or malfunctions).
• To prevent interference, keep audio
and video cables away from power
cords and speaker cables.
Wrong!
AV Cables and Jacks
Audio/Video
Cable
Jack
Description
HDMI connections can carry uncompressed stan-
dard- or high-definition digital video and audio and
offer the best picture and sound quality.
HDMI
HDMI
Video
Y
P
P
Y
Component video separates the luminance (Y) and
color difference signals (PR, PB), providing the best
picture quality. (Some TV manufacturers label their
component video jacks slightly differently.)
Y
Component
video cable
B
R
P
B
R
C
C
B/PB
P
R/PR
S-Video separates the luminance and color signals
and provides better picture quality than composite
video.
S
S-Video cable
Composite video is commonly used on TVs, VCRs,
and other video equipment.
Composite
video cable
V
Audio
This offers the best sound quality and allows you to
enjoy Dolby Digital and DTS. The audio quality is
the same as for coaxial.
OPTICAL
COAXIAL
Optical digital
audio cable
This offers the best sound quality and allows you to
enjoy Dolby Digital and DTS. The audio quality is
the same as for optical.
Coaxial digital
audio cable
This cable carries analog audio. It’s the most
common connection format for analog audio and
can be found on virtually all AV components.
L
Analog audio
cable (RCA)
R
This cable carries multichannel analog audio and is
typically used to connect DVD players with a 7.1-
channel analog audio output. Several standard
analog audio cables can be used instead of a multi-
channel cable.
FRONT CENTER
SURR SURR BACK
Multichannel
analog audio
cable (RCA)
SUBWOOFER
MULTI CH
Note: The AV receiver does not support SCART connections.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting Audio and Video Signals to the AV Receiver
By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you
can switch the audio and video signals simultaneously simply by changing the input source on the AV receiver.
: Signal Flow
Video
Video
Audio
Audio
TV, projector,
etc.
DVD player, etc.
Speakers (see page 22 for hookup details)
Which Connections Should I Use?
The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format
you choose will depend on the formats supported by your other components. Use the following sections as a guide.
For video components, you must make an audio connection and a video connection.
Audio Connection Formats
Audio Signal Flow Chart
Audio equipment can be connected to the AV
DVD player, etc.
receiver by using any of the following audio
analog multichannel, or HDMI.
HDMI Multichannel Optical Coaxial Analog
When you connect audio equipment to an
HDMI, OPTICAL, or COAXIAL input, you
AV receiver
must assign that input to an input selector (see
page 47).
HDMI
Analog
When choosing a connection format, bear in
mind that the AV receiver does not convert dig-
ital input signals for analog line outputs and
vice versa. For example, audio signals con-
not output by the analog TAPE OUT.
MD recorder, etc.
If signals are present at more than one input, the inputs will be selected automatically in the following order of priority:
HDMI, digital, analog (including multichannel). You can specify which audio inputs the AV receiver checks for the
presence of a signal in the “Automatic Audio Input Selection Setup” on page 49.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Video Connection Formats
Video Signal Flow Chart
Video equipment can be connected to the AV
receiver by using any one of the following
video connection formats: composite video,
S-Video, component video, or HDMI, the lat-
ter offering the best picture quality.
DVD player, etc.
Composite
S-Video
Component
HDMI
IN
Video input signals flow through the AV
receiver as shown, with composite video, S-
Video, and component video sources all being
upconverted for the HDMI output.
AV receiver
MONITOR OUT
Composite
S-Video
Component
HDMI
The composite video, S-Video, and component
input signals as they are.
TV, projector, etc.
When you connect audio equipment to an
HDMI or COMPONENT input, you must
assign that input to an input selector (see pages
46 and 47).
If signals are present at more than one input,
the inputs will be selected automatically in the
following order of priority: HDMI, component
video, S-Video, composite video. However, for
component video only, regardless of whether a
component video signal is actually present, if a
component video input is assigned to the input
selector, that component video input will be
selected. And if no component video input is
assigned to the input selector, this will be inter-
preted as no component video signal being
present.
Signal Selection Example
DVD player, etc.
Composite
S-Video
Component
HDMI
IN
AV receiver
MONITOR OUT
S-Video
Composite
Component
HDMI
In the Signal Selection Example shown on the
right, video signals are present at both the
S-Video and composite video inputs, however,
the S-Video signal is automatically selected as
the source and video is output by the S-Video
and HDMI outputs.
TV, projector, etc.
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the
composite video or S-Video MONITOR OUT, or the COMPONENT VIDEO OUT, use the HT-R667’s own display
when changing settings.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a TV or Projector
Step 1:Video Connection
Choose a video connection that matches your TV (
,
, or ), and then make the connection.
A
B
C
Step 2: Audio Connection
Choose an audio connection that matches your TV (
,
, or ), and then make the connection.
a
b
c
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the
composite video or S-Video MONITOR OUT, or the COMPONENT VIDEO OUT, use the HT-R667’s own display
when changing settings.
• To enjoy Dolby Digital and DTS, use connection or
.
b
c
Connection
AV receiver
COMPONENT VIDEO OUT
MONITOR OUT S
Signal flow
TV
Picture quality
Best
Component video input
S-Video input
⇒
⇒
⇒
⇐
⇐
⇐
A
B
C
a
Better
MONITOR OUT V
Composite video input
Analog audio L/R output
Digital coaxial output
Digital optical output
Standard
CBL/SAT IN L/R
DIGITAL IN COAXIAL 2
DIGITAL IN OPTICAL 1
b
c
ASSIGNABLE
IN 4
IN 3
(CBL/SAT)
IN 2
(VCR/DVR)
IN 1 (DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
MONITOR
COAXIAL
VCR/DVR
CBL/SAT
DVD
b
c
C
OUT
CB/PB
2
V
S
V
S
(CBL/SAT)
CR/PR
1
(VCR/DVR)
OPTICAL
IN 2 (CBL/SAT)
OUT
OUT
IN 1(DVD)
IN
IN
IN
IN
IN
OUT
OUT
B
ASSIGNABLE
2
(CD)
U
FRONT
SURR
CEN
IN
IN
ASSIGNABLE
E
L
L
R
R
REMOTE
A
SU
CONTROL
a
WOO
DVD
CBL/SAT
VCR/DVR
CD
TAPE
L
R
OUT
OPTICAL
OUT
Y
PB
PR
AUDIO
OUT
S VIDEO
IN
VIDEO
IN
COMPONENT VIDEO IN
Connect one or the other
TV, projector,
etc.
Connection must be assigned
c
(see page 47)
If your TV has no audio outputs, connect an audio output from your VCR or cable or satellite
Hint!
receiver to the AV receiver and use its tuner to listen to TV programs through the AV receiver (see
pages 32 and 34).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a DVD player
Step 1:Video Connection
Choose a video connection that matches your DVD player (
,
, or ), and then make the connection.
A
B
C
You must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your DVD player (
,
, or ), and then make the connection.
a
b
c
• To enjoy Dolby Digital and DTS, use connection or
.
b
c
• If your DVD player has main left and right outputs and multichannel left and right outputs, be sure to use the
main left and right outputs for connection
.
a
Connection
AV receiver
Signal flow
DVD player
Picture quality
Best
COMPONENT VIDEO IN 1
DVD IN S
Component video output
S-Video output
⇐
⇐
⇐
⇐
⇐
⇐
A
B
C
a
Better
DVD IN V
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
Standard
DVD IN FRONT L/R
DIGITAL IN COAXIAL 1
DIGITAL IN OPTICAL 1
b
c
ASSIGNABLE
IN 4
IN 3
(CBL/SAT)
IN 2
(VCR/DVR)
IN 1 (DVD)
OUT
b
c
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
MONITOR
COAXIAL
VCR/DVR
CBL/SAT
DVD
OUT
CB/PB
C
2
V
S
V
S
(CBL/SAT)
CR/PR
1
(VCR/DVR)
OPTICAL
IN 2 (CBL/SAT)
OUT
OUT
IN 1(DVD)
B
IN
IN
IN
IN
IN
OUT
OUT
ASSIGNABLE
2
(CD)
T
FRONT
SURR
CENT
IN
IN
ASSIGNABLE
R
L
L
a
R
R
A
REMOTE
SU
CONTROL
WOO
DVD
CBL/SAT
VCR/DVR
CD
TAPE
L
R
COAXIAL
OUT
OUT
Y
PB
PR
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
assigned (see page 47)
c
DVD player
To connect a DVD player or DVD-Audio/SACD-capable player with a
multichannel analog audio output, see page 31.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Hooking Up the Multichannel Input
If your DVD player supports multichannel audio formats such as DVD-Audio and SACD, and it has a multichannel
analog audio output, you can connect it to the AV receiver’s multichannel input.
Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT
L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your
DVD player. If your DVD player has a 5.1-channel analog audio output, don’t connect anything to the AV receiver’s
SURR BACK L/R jacks.
To select the multichannel input, see “BasicAV Receiver Operation” on page 50. To adjust the subwoofer sensitivity for
the multichannel input, see “Using the Audio Adjust Settings” on page 69–70.
HDMI
ASSIGNABLE
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
SURR BACK SPEAKERS
Bi-AMP for FRONT SPEAKERS
SURR SPEAKERS
FRONT SPEAKERS
L
L
DIGITAL IN
1
COMPONENT VIDEO
Y
AM
DOCK
(for DS-A1L)
(DVD)
MONITOR
OUT
CENTER SPEAKER
COAXIAL
VCR/DVR
CBL/SAT
DVD
CB/PB
2
R
R
V
S
V
S
(CBL/SAT)
ANTENNA
CR/PR
FM
75
1
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT)
IN 1(DVD)
OUT
OUT
IN
IN
IN
IN
IN
OUT
OUT
ASSIGNABLE
2
(CD)
PRE OUT
IN
IN
FRONT
SURR
CENTER
SURR BACK
L
ASSIGNABLE
SUB
WOOFER
L
L
L
R
R
R
R
REMOTE
SUB
CONTROL
WOOFER
ZONE
2
SPEAKERS
DVD
CD
TAPE
CBL/SAT
VCR/DVR
7.1 ch
5.1 ch
FRONT
SURR
CENTER
SURR BACK
L
L
R
R
SUB
WOOFER
DVD
L
R
L
R
L
R
FRONT
SURROUND
CENTER
SUB
WOOFER
SURR
BACK
DVD player
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a VCR or DVR for Playback
With this hookup, you can use the tuner in your VCR or DVR to listen to your favorite TV programs
via the AV receiver, which is useful if your TV has no audio outputs.
Hint!
Step 1:Video Connection
Choose a video connection that matches your VCR or DVR (
,
, or ), and then make the connection. You must
A
B
C
connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches your VCR or DVR (
,
, or ), and then make the connection.
a
b
c
• To enjoy Dolby Digital and DTS, use connection or
.
b
c
Connection
AV receiver
COMPONENT VIDEO IN 2
VCR/DVR IN S
Signal flow
VCR or DVR
Picture quality
Component video output
S-Video output
Best
Better
⇐
⇐
⇐
⇐
⇐
⇐
A
B
C
a
VCR/DVR IN V
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
Standard
VCR/DVR IN L/R
DIGITAL IN COAXIAL 2
DIGITAL IN OPTICAL 1
b
c
IN 4
IN 3
(CBL/SAT)
IN 2
(VCR/DVR)
IN 1 (DVD)
OUT
SURR BACK SPEAKERS
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
MONITOR
OUT
COAXIAL
VCR/DVR
CBL/SAT
DVD
b
c
C
CB/PB
2
V
S
V
S
(CBL/SAT)
CR/PR
1
(VCR/DVR)
OPTICAL
IN 2 (CBL/SAT)
OUT
OUT
IN 1(DVD)
IN
IN
IN
IN
IN
OUT
OUT
B
ASSIGNABLE
2
(CD)
O
FRONT
SURR
CEN
IN
IN
ASSIGNABLE
B
F
L
L
R
R
REMOTE
SU
CONTROL
a
WOO
DVD
CBL/SAT
VCR/DVR
CD
TAPE
A
L
R
COAXIAL
OUT
OPTICAL
OUT
Y
PB
PR
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
b
assigned (see page 47)
VCR or DVR
32
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a VCR or DVR for Recording
Step 1:Video Connection
Choose a video connection that matches your VCR or DVR ( or ), and then make the connection. The video
A
B
source to be recorded must be connected to the AV receiver via the same type of connection.
Step 2: Audio Connection
Make the audio connection
.
a
Connection
AV receiver
Signal flow
VCR or DVD recorder
S-Video input
Picture quality
Better
VCR/DVR OUT S
VCR/DVR OUT V
VCR/DVR OUT L/R
⇒
⇒
⇒
A
B
a
Composite video input
Audio L/R input
Standard
ASSIGNABLE
IN 4
IN 3
(CBL/SAT)
IN 2
(VCR/DVR)
IN 1 (DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
MONITOR
COAXIAL
VCR/DVR
CBL/SAT
DVD
OUT
CB/PB
B
A
2
V
S
V
S
(CBL/SAT)
CR/PR
1
(VCR/DVR)
OPTICAL
IN 2 (CBL/SAT)
OUT
OUT
IN 1(DVD)
IN
IN
IN
IN
IN
OUT
OUT
ASSIGNABLE
2
(CD)
FRONT
SURR
CENT
IN
IN
ASSIGNABLE
L
L
R
R
REMOTE
SUB
CONTROL
WOOF
a
DVD
CBL/SAT
VCR/DVR
CD
TAPE
L
R
AUDIO
IN
S VIDEO
IN
VIDEO
IN
VCR or DVR
Notes:
• The AV receiver must be turned on for recording. Recording is not possible while it’s on Standby.
• If you want to record directly from your TV or another video source without going through the AV receiver, connect
the audio and video outputs from your TV or other video component directly to the recording VCR/DVR’s audio and
video inputs. See the manuals supplied with your TV or VCR/DVR for details.
• Video signals connected to composite video inputs can only be recorded via the VCR/DVR OUT V jack. So if your
source TV or VCR is connected to a composite video input, the recording VCR/DVR must be connected to the
VCR/DVR OUTV jack. Likewise, video signals connected to S-Video inputs can only be recorded via theVCR/DVR
OUT S jack. So if your source TV or VCR is connected to an S-Video input, the recording VCR/DVR must be
connected to the VCR/DVR OUT S jack.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Satellite, Cable, or Terrestrial Set-top box or Other Video Source
With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs
via the AV receiver, which is useful if your TV has no audio outputs.
Hint!
Step 1:Video Connection
Choose a video connection that matches the video source (
,
, or ), and then make the connection.
A
B
C
You must connect the AV receiver to your TV with the same type of connection.
Step 2: Audio Connection
Choose an audio connection that matches the video source (
,
, or ), and then make the connection.
a
b
c
• To enjoy Dolby Digital and DTS, use connection or
.
b
c
Connection
AV receiver
COMPONENT VIDEO IN 2
CBL/SAT IN S
Signal flow
Video source
Component video output
S-Video output
Picture quality
Best
Better
⇐
⇐
⇐
⇐
⇐
⇐
A
B
C
a
CBL/SAT IN V
Composite video output
Analog audio L/R output
Digital coaxial output
Digital optical output
Standard
CBL/SAT IN L/R
DIGITAL IN COAXIAL 2
DIGITAL IN OPTICAL 1
b
c
HDMI
ASSIGNABLE
IN 4
IN 3
(CBL/SAT)
IN 2
(VCR/DVR)
IN 1 (DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
MONITOR
OUT
COAXIAL
VCR/DVR
CBL/SAT
DVD
b
c
C
CB/PB
2
V
S
V
S
(CBL/SAT)
CR/PR
1
(VCR/DVR)
OPTICAL
IN 2 (CBL/SAT)
OUT
OUT
IN 1(DVD)
IN
IN
IN
IN
IN
OUT
OUT
B
ASSIGNABLE
2
(CD)
U
FRONT
SURR
CEN
IN
IN
ASSIGNABLE
L
L
R
R
A
REMOTE
SU
CONTROL
a
WOO
DVD
CBL/SAT
VCR/DVR
CD
TAPE
L
R
COAXIAL
OUT
OPTICAL
OUT
Y
PB
PR
AUDIO
OUT
S VIDEO
OUT
VIDEO
OUT
COMPONENT VIDEO OUT
Connect one or the other
Connection must be
c
assigned (see page 47)
Satellite, cable, set-top box, etc.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting Components with HDMI
About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital
interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now,
several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can
carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital
audio, or multichannel PCM).
*1
The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface), so TVs and displays
with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and
displays, resulting in no picture.)
The AV receiver uses HDCP (High-bandwidth Digital Content Protection), so only HDCP-compatible components will
display a picture.
The AV receiver’s HDMI interface is based on the following standard:
Repeater System, Deep Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby
TrueHD, Dolby Digital Plus, SA-CD and Multichannel PCM
Supported Audio Formats
• 2-channel linear PCM (16/20/24 bit/32–192kHz)
• Multichannel linear PCM (7.1 ch, 32–192kHz)
• Bitstream (Dolby Digital, Dolby Digital Plus, DTS, DTS-HD MasterAudio, DTS-HD High ResolutionAudio, Dolby
TrueHD, DSD)
Your DVD player must be able to output these formats from its HDMI OUT.
About Copyright Protection
*2
The AV receiver supports HDCP (High-bandwidth Digital Content Protection), a copy-protection system for digital
video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.
Use a commercially available HDMI cable (supplied with some components) to connect the AV receiver’s HDMI OUT
to the HDMI input on your TV or projector.
*1 DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999.
*2 HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. It’s designed to
protect video content and requires a HDCP-compatible device to display the encrypted video.
*3 DDWG (Digital Display Working Group): Led by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open
industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and
digital displays.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Making HDMI Connections
Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV,
projector, and so on.
Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 46).
■ Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.
Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Con-
nection Formats” on page 28 for more information.
■ Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV
receiver. Normally, they are not output by the HDMI OUT, unless the Audio TV Out setting is set to On (see page 82).
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the Audio TV Out
Hint!
setting to On (see page 82), and set your DVD player’s HDMI audio output setting to PCM.
HDMI
IN
HDMI
OUT
TV
DVD player
IN 1 (DVD)
OUT
HDMI
ASSIGNABLE
(VCR/DVR) IN
IN
4
IN
3
(CBL/SAT)
IN
2
1
(DVD)
OUT
SURR BACK
L
DIGITAL IN
COMPONENT VIDEO
Y
AM
DOCK
(for DS-A1L)
1
(DVD)
MONITOR
OUT
COAXIAL
VCR/DVR
CBL/SAT
DVD
CB/PB
2
R
V
V
S
(CBL/SAT)
ANTENNA
CR/PR
FM
75
1
S
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT)
IN 1(DVD)
OUT
OUT
IN
IN
IN
IN
IN
OUT
OUT
ASSIGNABLE
2
(CD)
IN
IN
FRONT
SURR
CENTER SURR BACK
ASSIGNABLE
L
L
L
R
R
R
REMOTE
SUB
CONTROL
WOOFER
DVD
CD
TAPE
CBL/SAT
VCR/DVR
Notes:
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In
addition, video signals from a PC are not supported.
• To listen to an HDMI source component through the AV receiver, you must configure your system so that video from
the HDMI source component can be displayed on your TV (i.e., on your TV, select the HDMI input that’s connected
to the AV receiver’s HDMI OUT). This is necessary because a component identification check has to be performed
on your TV before an HDMI source component can output any signals. If your TV is off or set to a different input
source, the AV receiver may produce no sound or the sound may be distorted.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the
picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected
component’s instruction manual for details.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Camcorder, Game Console, or Other Device
Step 1: Make the video connection
Step 2: Make the audio connection
.
.
A
a
MASTER VOLUME
a
TUNING
PRESET
AUX INPUT
AUDIO
L
R
ENTER
L
AUDIO
OUT
R
SETUP
RETURN
AUX INPUT
AUDIO
SETUP MIC
VIDEO
L
R
A
AUX INPUT
VIDEO
VIDEO OUT
Camcorder, game console, etc.
Connection
AV receiver
AUX INPUT VIDEO
AUX INPUT L-AUDIO-R
Signal flow
Camcorder or console
Composite video output
Analog audio L/R output
⇐
⇐
A
a
Connecting the Supplied DS-A1L Dock
HDMI
ASSIGNABLE
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
A
(DVD)
DOCK
(for DS-A1L)
MONITOR
OUT
COAXIAL
VCR/DVR
CBL/SAT
DVD
CB/PB
2
V
S
(CBL/SAT)
V
S
ANTENNA
CR/PR
1
FM
75
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT) IN 1(DVD)
ASSIGNABLE
OUT
OUT
IN
IN
OUT
OUT
IN
IN
IN
2
(CD)
IN
IN
FRONT
SURR
CENTER
SURR BACK
ASSIGNABLE
L
L
L
R
R
R
REMOTE
SUB
CONTROL
WOOFER
DVD
CD
TAPE
CBL/SAT
VCR/DVR
Notes:
• To connect an RI dock other than the DS-A1L, refer to its instruction manual.
• While your iPod is seated in the Dock, its battery will be charged when the AV receiver is set to On or Standby.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a CD Player or Turntable
■ CD Player or Turntable (MM) with Built-in Phono Preamp
Step 1:
Choose a connection that matches your CD player (
phono preamp.
,
, or ). Use connection for a turntable with a built-in
a
b
c
a
HDMI
ASSIGNABLE
IN
4
IN
3
(CBL/SAT)
Y
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
COAXIAL
b
DIGITAL IN
1
(DVD)
COMPONENT VIDEO
IN
2
DOCK
(for DS-A1L)
(CBL/SAT)
L
L
COAXIAL
CBL/SAT
VCR/DVR
DVD
CB/PB
2
V
S
(CBL/SAT)
Connect one
or the other
CR/PR
R
R
1
c
OPTICAL
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT)
ASSIGNABLE
OUT
OUT
IN 1(DVD)
AUDIO
OUTPUT
CD
IN
IN
T
OUT
IN
IN
IN
2
2
(CD)
IN
IN
FRONT
(CD)
Connection
must be
b
ASSIGNABLE
L
L
IN
a
L
R
R
REMOTE
CONTROL
assigned (see
page 47)
CBL/SAT
VCR/DVR
CD
TAPE
R
CD
a
COAXIAL
OUT
L
R
Turntable (MM) with
built-in phono preamp
OPTICAL
OUT
AUDIO
OUT
CD player
• To connect the CD player digitally, use connection or
.
b
c
Connection
AV receiver
Signal flow
CD or turntable
CD IN L/R
Analog audio L/R output
Digital coaxial output
Digital optical output
⇐
⇐
⇐
a
b
c
DIGITAL IN COAXIAL 2
DIGITAL IN OPTICAL 2
■ Turntable (MM) with no Phono Preamp Built-in
A phono preamp is necessary to connect a turntable that
doesn’t have a phono preamp built-in.
■ Turntable with an MC (Moving Coil) Cartridge
An MC head amp and phono preamp are necessary to
connect a turntable with an MC (Moving Coil) cartridge.
HDMI
HDMI
ASSIGNABLE
IN
ASSIGNABLE
IN
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
1
(DVD)
OUT
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
1
(DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
Y
DOCK
(for DS-A1L)
(DVD)
(DVD)
COAXIAL
CBL/SAT
VCR/DVR
DVD
COAXIAL
CBL/SAT
VCR/DVR
DVD
CB/PB
CB/PB
2
2
V
S
(CBL/SAT)
V
S
(CBL/SAT)
CR/PR
CR/PR
1
1
(VCR/DVR)
(VCR/DVR)
OPTICAL
OPTICAL
IN
2
(CBL/SAT) IN 1(DVD)
ASSIGNABLE
OUT
OUT
IN
2
(CBL/SAT)
IN 1(DVD)
OUT
OUT
IN
IN
OUT
OUT
IN
IN
IN
IN
IN
OUT
OUT
IN
IN
IN
ASSIGNABLE
2
2
(CD)
IN
IN
FRONT
(CD)
IN
IN
FRONT
ASSIGNABLE
ASSIGNABLE
L
L
L
L
R
R
R
R
REMOTE
REMOTE
CONTROL
CONTROL
CD
TAPE
CBL/SAT
VCR/DVR
CBL/SAT
VCR/DVR
CD
TAPE
AUDIO
INPUT
AUDIO
AUDIO
OUTPUT
AUDIO
OUTPUT
IN
OUTPUT
IN
L
L
Phono preamp
L
L
L
L
R
R
R
R
R
R
Phono
preamp
CD
CD
MC head amp or
MC transformer
AUDIO
OUTPUT
AUDIO
INPUT
L
L
AUDIO
OUTPUT
AUDIO
INPUT
R
R
L
L
R
R
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting a Cassette, CDR, MiniDisc, or DAT Recorder
Step 1:
Choose a connection that matches your recorder (
,
, or ), and then make the connection.
a
b
c
HDMI
ASSIGNABLE
COAXIAL
b
IN
a
a
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
L
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
AM
2
(DVD)
(CBL/SAT)
MONITOR
OUT
R
COAXIAL
VCR/DVR
CBL/SAT
DVD
CB/PB
2
V
S
V
S
(CBL/SAT)
ANTENNA
TAPE
CR/PR
FM
75
c
OPTICAL
1
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT)
OUT
OUT
IN 1(DVD)
2
(CD)
IN
IN
IN
IN
IN
OUT
OUT
ASSIGNABLE
2
(CD)
IN
IN
FRONT
SURR
CENTER
SURR BACK
L
ASSIGNABLE
L
L
L
R
R
R
R
REMOTE
SUB
CONTROL
TAPE
WOOFER
DVD
CD
TAPE
CBL/SAT
VCR/DVR
L
R
L
R
Connect one or the other
These connections must be
assigned (see page 47)
COAXIAL
OUT
OPTICAL
OUT
AUDIO
IN
AUDIO
OUT
Cassette, CDR, MD, etc.
• To connect the recorder digitally for playback, use connections and , or and
.
a
b
a
c
Connection
a
AV receiver
Signal flow
Cassette, CDR, MD, or DAT recorder
⇐
⇒
TAPE IN L/R
TAPE OUT L/R
Analog audio L/R output
Analog audio L/R input
DIGITAL IN COAXIAL 2
DIGITAL IN OPTICAL 2
Digital coaxial output
Digital optical output
⇐
⇐
b
c
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ConnectingYour Components—Continued
Connecting Onkyo
Components
Step 1: Make sure that each Onkyo component is connected to the AV receiver with an analog audio cable (RCA).
Step 2: Make the necessary connections (see illustration below).
Step 3: If you’re using an MD or CDR component, change the Input Display (see page 48).
With
(Remote Interactive), you can use the following special functions:
Auto Power On/Standby
When you start playback on a component connected via
, if the AV receiver is on Standby, it will automatically turn
on and select that component as the input source. Similarly, when the AV receiver is set to Standby, all components
connected via
will also go on Standby.
Direct Change
When playback is started on a component connected via
, the AV receiver automatically selects that component as
the input source. If your DVD player is connected to the AV receiver’s DVD IN (multichannel input), you’ll need to
press the [MULTI CH] button repeatedly and select Multich to hear all channels (see page 50), as the Direct Change
function selects the DVD IN FRONT L/R jacks.
Remote Control
You can use the AV receiver’s remote controller to control your other
-capable Onkyo components. You must enter
the appropriate remote control code first (see page 85). And remember to point the remote controller at the AV receiver
and not the other component.
Notes:
IN
• Use only
are supplied with Onkyo players (DVD, CD, etc.).
• Some components have two jacks. You can con-
nect either one to the AV receiver. The other jack is
for connecting additional -capable components.
• Connect only Onkyo components to jacks. Con-
cables for
connections.
cables
HDMI
ASSIGNABLE
IN
L
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
1
(DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
Y
DOCK
(for DS-A1L)
(DVD)
R
MONITOR
OUT
COAXIAL
CBL/SAT
VCR/DVR
DVD
CB/PB
2
V
S
(CBL/SAT)
CD
V
S
CR/PR
1
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT) IN 1(DVD)
ASSIGNABLE
OUT
OUT
IN
IN
OUT
OUT
IN
IN
IN
2
(CD)
IN
IN
FRONT
SURR
ASSIGNABLE
FRONT
L
L
L
R
R
REMOTE
CONTROL
REMOTE
CONTROL
W
CBL/SAT
VCR/DVR
DVD
CD
TAPE
R
necting other manufacturer’s components may cause
a malfunction.
DVD
• Some components may not support all
Refer to the manuals supplied with your other Onkyo
components.
functions.
e.g., CD player
e.g., DVD player
R
L
ANALOG
AUDIO OUT
R
L
ANALOG
AUDIO OUT
Connecting the Power Cord
• Before connecting the power cord, connect all your speakers and AV components.
• Plug the end of the power cord into a suitable wall outlet.
• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the AV Receiver
ON/STANDBY
ON/STANDBY
RECEIVER
STANDBY indicator
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
Turning On and Standby
The onscreen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the
composite video or S-Video MONITOR OUT, or the COMPONENT VIDEO OUT, use the HT-R667’s own display
when changing settings.
Remote
On the AV receiver, press the [ON/STANDBY] button.
AV receiver
controller
ON/STANDBY
On the remote controller, press the [RECEIVER] REMOTE MODE button,
followed by the [ON/STANDBY] button.
or
The AV receiver comes on, the display lights up, and the STANDBY indicator goes off.
To turn the AV receiver off, press the [ON/STANDBY] button, or press the remote
controller’s [ON/STANDBY] button. The AV receiver will enter Standby mode. To
prevent any loud surprises the next time you turn on the AV receiver, turn down the
volume before you turn it off.
To get your system up and running with the minimum of fuss, here’s a few pointers to help you configure the AV
receiver before you use it for the very first time. These settings only need to be made once.
See “Automatic Speaker Setup” on page 42.
■ Did you connect a component to an HDMI input,
Y
HDMI
COAXIAL
PB
If you did, see “HDMI Input Setup” on page 46, “Component Video
Input Setup” on page 47, or “Digital Input Setup” on page 47 respec-
PR
OPTICAL
tively.
■ Did you connect an Onkyo MD recorder or CD recorder?
OUT
IN
If you did, see “Changing the Input Display” on page 48.
TAPE
MD recorder, CD recorder
41
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup
This section explains the settings that you need to make before using the AV receiver for the very first time.
®
Using Audyssey 2EQ
Automatic Speaker Setup
With the supplied calibrated microphone, Audyssey
2EQ automatically determines the number of speakers
Notes:
®
• If the AV receiver is muted, it will be unmuted
automatically when the automatic speaker setup
starts.
connected, their size for purposes of bass management,
optimum crossover frequencies to the subwoofer (if
present), and distances from the primary listening posi-
tion. Audyssey 2EQ then removes the distortion caused
by room acoustics by capturing room acoustical prob-
time domain. The result is clear, well-balanced sound for
everyone. Enabling Audyssey 2EQ allows you to also
use Audyssey Dynamic EQ, which maintains the proper
octave-to-octave balance at any volume level. (See
page 72)
• Automatic speaker setup cannot be performed
while a pair of headphones is connected.
• It takes about 10 minutes to complete the auto-
matic speaker setup for three positions. Total mea-
surement time varies depending on the speakers.
• Do not connect or disconnect any speakers during
the automatic speaker setup.
Measurement Positions
To create a listening environment in your home theater
that all listeners will enjoy, Audysssey 2EQ takes mea-
surements at up to three positions within the listening
area.
1
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
A First measurement point
This is the center point of the listening area, or the
listening position.
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
B Second measurement point
2, 8
3-7
The right side of the listening area.
C Third measurement point
The left side of the listening area.
The distances between points 1and 2and points 1
and 3must be at least 1 meter.
From the examples below, choose the listening area that
best matches yours and place the microphone accord-
ingly when prompted.
TV
TV
TV
TV
TV
TV
TV
TV
TV
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the composite video or S-Video MONITOR OUT,
or the COMPONENT VIDEO OUT, use the HT-
R667’s own display when changing settings.
Turn on the AV receiver and the
connected TV.
1
ON/STANDBY
On the TV, select the input to which the
AV receiver is connected.
:
:
Listening area
Listening position
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Put the speaker setup micro-
phone at measurement point 1
Press [ENTER].
The automatic speaker setup starts.
2
3
SETUP MIC
(page 42), and connect it to the
Auto Speaker Setup
AUDYSSEY
SETUP MIC jack.
Auto Speaker Setup
AUDYSSEY
Do not unplug microphone.
Please keep quiet.
Please place microphone at center
of listening area at ear height.
Now Measuring. . .
Push Enter
:
Next
Test tones are played through each
speaker as Audyssey 2EQ Automatic
Speaker Setup runs. This process takes
a few minutes. Please refrain from
talking during measurements and do
not stand between speakers and the
microphone.
Notes:
• Before starting Audyssey 2EQ
®
Automatic Speaker Setup, arrange
the room and connect the speakers as
you would for enjoying movies.
Changes to the room after auto setup
requires you run the auto setup again,
as room EQ characteristics may have
changed.
The following screen appears.
4
Auto Speaker Setup
AUDYSSEY
• When starting the automatic speaker
setup, do not stand between the
speakers and microphone, and avoid
obstacles blocking the path between
speakers and microphone. This will
produce inaccurate results.
Please place microphone at right end
of listening area at ear height.
Push Enter
:
Next
• Position the microphone at ear height
of a seated listener with the micro-
phone tip pointed directly at the ceil-
ing using a tripod. Do not hold the
microphone in your hand during
measurements as this will produce
inaccurate results.
Move the speaker setup micro-
phone to measurement point 2
(page 42), then press [ENTER].
Audyssey 2EQ performs more mea-
surements. This takes a few minutes.
The following screen appears.
5
• Make the room as quiet as possible.
Background noise can disrupt the
room measurements. Close win-
dows, silence cell phones, televi-
sions, radios, air conditioners,
Auto Speaker Setup
AUDYSSEY
Please place microphone at left end
of listening area at ear height.
fluorescent lights, home appliances,
light dimmers, or other devices.
Push Enter
:
Next
• Cell phones should be turned off or
placed away from all audio electron-
ics during the measurement process
as Radio Frequency Interference
(RFI) may cause measurement dis-
ruptions (even if the cell phone is not
in use).
Move the speaker setup micro-
phone to measurement point 3
(page 42), then press [ENTER].
Audyssey 2EQ performs more mea-
surements. This takes a few minutes.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Error Messages
When the measurements are
complete, the following screen
appears.
6
While the automatic speaker setup is in progress, one of
the following error messages may appear:
Auto Speaker Setup
AUDYSSEY
❏ Ambient noise is too high
Auto Speaker Setup
AUDYSSEY
Calculating...
Ambient noise is too high.
Retry
Cancel
When the calculations are com-
plete, the following screen
appears.
7
This message appears if the background noise is too
loud and the measurements cannot be performed
properly.
AUDYSSEY
Auto Speaker Setup
Review Speaker configuration
Remove the source of the noise and try again.
Retry: Return to the measured point immediately
before and start set up again.
Subwoofer
Front
:
:
:
:
:
:
No
40Hz
40Hz
40Hz
40Hz
1ch
Center
Surround
Surr Back
Surr Back Ch
Cancel: Cancel the automatic speaker setup.
Save
Cancel
❏ Speaker Detect Errors
Auto Speaker Setup
AUDYSSEY
Use the Up and Down [ ]/[
]
- - - - - Speaker Detect Error - - - - -
buttons to select an option, and
then press [ENTER].
The options are:
FL
SL
SBL
C
:
:
:
:
Yes
---
:
:
:
:
No
---
---
---
FR
SR
---
SBR
SW
Yes
Save:
Retry
Cancel
Save the calculated settings and exit
the automatic speaker setup.
Cancel:
One of the front speakers has not been detected.
Cancel the automatic speaker setup.
Auto Speaker Setup
AUDYSSEY
- - - - - Speaker Detect Error - - - - -
Note:
FL
SL
SBL
C
:
:
:
:
Yes
---
FR
:
:
:
:
Yes
No
---
SR
• You can view the calculated settings
for the speaker configuration,
speaker distances, and speaker levels
by using the Left and Right [ ]/[
buttons.
---
SBR
SW
Yes
---
Retry
Cancel
]
One of the surround speakers has not been detected.
Disconnect the speaker setup
microphone.
8
Auto Speaker Setup
AUDYSSEY
Auto Speaker Setup
AUDYSSEY
- - - - - Speaker Detect Error - - - - -
FL
SL
SBL
C
:
:
:
:
Yes
---
:
:
:
:
Yes
No
Yes
---
FR
SR
---
SBR
SW
Please unplug microphone.
Yes
Retry
Cancel
The surround back speakers have been detected but
the surround speakers haven’t.
Note:
• When the automatic speaker setup is complete, the
Equalizer Settings (page 78) will be set to “Audyssey.”
44
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Auto Speaker Setup
AUDYSSEY
To Retry the Automatic Speaker Setup
- - - - - Speaker Detect Error - - - - -
FL
SL
SBL
C
:
:
:
:
Yes
---
No
Yes
:
:
:
:
Yes
Yes
Yes
---
FR
Press the [ENTER] button.
Make sure speakers that cannot be
detected are connected properly.
SR
SBR
SW
Retry
Cancel
The right surround back speaker has been detected
but the left surround back speaker hasn’t.
Changing the Speaker Settings Manually
If you wish to make changes to the settings found during
the automatic speaker setup, follow the directions on
pages 74–78.
Auto Speaker Setup
AUDYSSEY
- - - - - Speaker Detect Error - - - - -
FL
SL
SBL
C
:
:
:
:
Error
Yes
:
:
:
:
Yes
Yes
Yes
Yes
FR
SR
Yes
SBR
SW
Yes
Using a Powered Subwoofer
Retry
Cancel
If you’re using a powered subwoofer and it outputs very
low-frequency sound at a low volume level, it may not be
detected by the automatic speaker setup. If the sub-
woofer (SW) appears on the “SP Detect Result” screen
as “No”, increase the subwoofer’s volume to the half-
way point, set it to its highest crossover frequency, and
then try running the automatic speaker setup again. Note
that if the volume is set too high and the sound distorts,
detection issues may occur, so use an appropriate
volume level.
There is a problem with a speaker. The speaker may
be broken or the subwoofer may be emitting sound
that is too high.
Auto Speaker Setup
AUDYSSEY
Speaker Detect Error
Retry
Cancel
The number of speakers detected on the second or
third measurement was different to the number
detected on the first measurement.
Make sure speakers that cannot be detected are con-
nected properly.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
❏ Write Error
Auto Speaker Setup
AUDYSSEY
Writing Error!
Retry
Cancel
This message appears if saving fails.
Try saving again. If this message appears after 2 or 3
attempts, the AV receiver is probably malfunctioning.
Contact your Onkyo dealer.
Retry: Return to step 2 and try again.
Cancel: Cancel the automatic speaker setup.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
HDMI Input Setup
Use the Up and Down [ ]/[
buttons to select an input selec-
tor, and use the Left and Right
]
4
If you connect a video component to an HDMI IN, you
must assign that input to an input selector. For example,
if you connect your DVD player to HDMI IN 1, you
must assign HDMI IN 1 to the DVD input selector.
[
]/[ ] buttons to select:
HDMI1: Select if the video compo-
nent is connected to HDMI
IN 1.
These are the default assignments.
Input selector
DVD
Video input
HDMI1
HDMI2
HDMI3
- - - - -
HDMI2: Select if the video compo-
nent is connected to HDMI
IN 2.
HDMI3: Select if the video compo-
nent is connected to HDMI
IN 3.
VCR/DVR
CBL/SAT
AUX
HDMI4: Select if the video compo-
nent is connected to HDMI
IN 4.
TAPE
- - - - -
CD
- - - - -
- - - - -: Select if you’re not using the
HDMI OUT.
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
1
Press the [SETUP] button.
Setup closes.
5
Notes:
Use the Up and Down [ ]/[
buttons to select “1. Input
Assign,” and then press
[ENTER].
]
2
3
input selector.
• When an HDMI IN is assigned to an input selector as
explained here, the digital audio input for that input
selector is automatically set to the same HDMI IN.
See “Digital Input Setup” on page 47.
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
Use the Up and Down [ ]/[
buttons to select“1. HDMI Input,”
and then press [ENTER].
]
46
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Component Video Input Setup
Use the Up and Down [ ]/[
buttons to select an input selec-
tor, and use the Left and Right
]
4
If you connect a video component to a COMPONENT
VIDEO IN, you must assign that input to an input
selector. For example, if you connect your DVD player
to COMPONENT VIDEO IN 2, you must assign COM-
PONENT VIDEO IN 2 to the DVD input selector.
[
]/[ ] buttons to select:
IN1: Select if the video compo-
nent is connected to COM-
PONENT VIDEO IN 1.
IN2: Select if the video compo-
nent is connected to COM-
PONENT VIDEO IN 2.
- - - - -: Select if you’re not using the
COMPONENT VIDEO
These are the default assignments.
Input selector
DVD
Video input
IN1
VCR/DVR
CBL/SAT
AUX
- - - - -
IN2
OUT.
- - - - -
- - - - -
- - - - -
Press the [SETUP] button.
Setup closes.
TAPE
5
CD
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Note:
1
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
Digital Input Setup
Use the Up and Down [ ]/[
buttons to select “1. Input
Assign,” and then press
[ENTER].
]
2
3
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example,
if you connect your CD player to OPTICAL IN 1, you
must assign OPTICAL IN 1 to the CD input selector.
These are the default assignments.
Input selector
DVD
Audio input
COAX1
OPT1
VCR/DVR
CBL/SAT
AUX
COAX2
- - - - -
Use the Up and Down [ ]/[
]
buttons to select “2. Component
Video Input,” and then press
[ENTER].
TAPE
- - - - -
CD
OPT2
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
1
47
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
the“Automatic Audio Input Selection Setup” on
page 49 to the same input (e.g., COAX1 (Auto) or
COAX2 (Auto)).
Use the Up and Down [ ]/[
]
]
]
2
buttons to select “1. Input
Assign,” and then press
[ENTER].
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
Changing the Input Display
If you connect an
-capable Onkyo MiniDisc recorder
or CD recorder to the TAPE IN/OUT jacks, for
work properly, you must change this setting.
to
Use the Up and Down [ ]/[
3
buttons to select “3. Digital
Audio Input,” and then press
[ENTER].
This setting can only be changed on the AV receiver.
1, 2
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
Use the Up and Down [ ]/[
4
buttons to select an input selec-
tor, and then use the Left and
Right [ ]/[ ] buttons to select:
COAX1: Select if the component is
connected to DIGITAL IN
COAXIAL 1.
COAX2: Select if the component is
connected to DIGITAL IN
COAXIAL 2.
OPT1: Select if the component is
connected to DIGITAL IN
OPTICAL 1.
OPT2: Select if the component is
connected to DIGITAL IN
OPTICAL 2.
Press the [TAPE] input selector
button so that “TAPE” appears
on the display.
1
2
TAPE
Press and hold down the [TAPE]
input selector button (about 3
seconds) to change the setting.
Repeat this step to select MD or CDR.
TAPE
For the TAPE input selector, the setting
changes in this order:
TAPE → MD → CDR
- - - - -: Select if the component is
connected to an analog
input.
Press the [SETUP] button.
Setup closes.
5
Notes:
• When an HDMI IN is assigned to an input selector in
“HDMI Input Setup” on page 46, this input assign-
ment is automatically set to the same HDMI IN. And
in addition to the usual inputs (e.g., COAX1, COAX2,
etc.), you can also select HDMI inputs. If you change
the input assignment from an HDMI IN to one of the
other inputs (e.g., COAX1 or COAX2), be sure to set
48
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup—Continued
Automatic Audio Input Selection
Setup
Press the [DIGITAL INPUT] but-
ton repeatedly to select an
option.
3
DIGITAL INPUT
HDMIx (Auto):
This option can be selected when an
HDMI input is assigned to an input
selector (page 46). When this option is
selected, the relevant HDMI, digital,
and analog inputs will be checked for
the presence of an audio signal. If sig-
nals are present at more than one input,
the inputs will be selected in the follow-
analog.
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
1
2, 3
When an input source is selected, the AV receiver checks
the relevant audio inputs for the presence of an audio
signal and automatically selects an input. With this set-
ting, you can specify which audio inputs the AV receiver
will check for signals.
COAXx (Auto)/OPTx (Auto):
This option can be selected when a dig-
ital input is assigned to an input selector
(page 47). When this option is selected,
the relevant digital and analog inputs
will be checked for the presence of an
audio signal. If signals are present at
more than one input, the inputs will be
selected in the following order of prior-
ity: digital, analog. Any audio signals
present at the HDMI inputs will not be
output.
Press the input selector button
for the input selector whose set-
ting you want to change.
The setting for the TUNER input selec-
tor cannot be changed and is fixed at
“Analog.”
1
DVD
VCR/DVR CBL/SAT
AUX
CD
TAPE
TUNER
Analog:
When this option is selected, the signal
from the relevant analog audio input is
output. Any audio signals present at
HDMI or digital inputs will not be out-
put.
Press the [DIGITAL INPUT]
button.
The current setting is displayed.
2
DIGITAL INPUT
Note:
• You can select a different option for each input selec-
tor.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
PlayingYour AV Components
Basic AV Receiver Operation
Subwoofer’s
rear panel
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
1, 2
3
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
4
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
MAX
OUTPUT LEVEL
MIN
1
3
Use the AV receiver’s input selector buttons to select an input source.
Remote
controller
1
AV receiver
To select an input source with the remote controller, press its INPUT
SELECTOR buttons.
DVD
VCR/DVR CBL/SAT
To listen to a DVD player connected to the multichannel DVD input (page 31), press
display.
AUX
CD
TAPE
TUNER
Note:
• While the multichannel DVD input is selected, the Speaker Configuration settings on
page 74 are ignored, and signals from the multichannel input are fed to the speakers
as they are.
To turn the speaker on or off, use the AV receiver’s SPEAKERS [A] and
[B] buttons, or press the [RECEIVER] REMOTE MODE button on the
remote controller and use its [SP A/B] button.
2
Remote
controller
AV receiver
A
SPEAKERS
B
Pressing the remote controller’s [SPA/B] button cycles through the following settings:
Speaker Set A → Speaker Set A&B → Speaker Set B → Off.
TheA and B speaker indicators show whether each
speaker set is on or off.
Indicators
Note that when speaker set B is turned on, speaker
set A is reduced to 5.1-channel playback.
SP A/B
Start playback on the source component.
To watch a DVD or other video source, on your TV, select the video input that’s con-
nected to the AV receiver’s COMPONENT VIDEO OUT, HDMI OUT, or MONITOR
OUT.
On some DVD players, you may need to change the digital or HDMI audio output
settings.
3
4
To adjust the volume, use the MASTER VOLUME control or the remote
controller’s [VOL] button.
Since the AV receiver is designed for home theaters, it has a wide volume range for
precise adjustment. The volume can be set to Min, 1 through 79, or Max.
Remote
controller
AV receiver
MASTER VOLUME
Note: When the subwoofer volume level is set to a positive (+) value, the maximum
master volume level is reduced proportionally.
To set the level of the subwoofer, use the OUTPUT LEVEL control.
Because our ears are less sensitive to very low bass sounds, there’s a temptation to set
the level of the subwoofer too high. As a rule of thumb, set the subwoofer level to what
you think is the optimal level, and then back it off slightly.
Select a listening mode and enjoy!
See “Using the Listening Modes” on page 59.
5
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Functions
This section explains functions that can be used with any
input source.
Muting the AV Receiver
You can temporarily mute the output of the AV receiver.
DISPLAY
Press the [RECEIVER] REMOTE
MODE button, and then press the
remote controller’s [MUTING]
button.
Press
[RECEIVER]
first
MUTING
The output is muted and the MUTING
indicator flashes on the display.
To unmute the AV receiver, press the remote control-
ler’s [MUTING] button again, or adjust the volume. The
output is unmuted and the MUTING indicator goes off.
Muting is cancelled when the AV receiver is set to
Standby.
Using the Sleep Timer
DIMMER
SLEEP
With the sleep timer, you can set the AV receiver so that
it turns off automatically after a specified period.
Press the [RECEIVER] REMOTE
MODE button, and then press the
remote controller’s [SLEEP] but-
ton repeatedly to select the
required sleep time.
DISPLAY
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
You can set the sleep time from 90 to 10
minutes in 10 minute steps.
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
The SLEEP indicator appears on the
display when the sleep timer has been
set, as shown. The specified sleep time
appears on the display for about 5 sec-
onds, then the previous display reap-
pears.
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
PHONES
DIMMER
SLEEP indicator
Setting the Display Brightness
You can adjust the brightness of the display.
Remote
Press the [RECEIVER] REMOTE
MODE button, and then press the
remote controller’s [DIMMER]
button repeatedly to select: dim,
dimmer, or normal brightness.
You can also use the AV receiver’s
[DIMMER] button.
controller
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
To check the remaining sleep time, press the [SLEEP]
button. Note that if you press the [SLEEP] button while
the sleep time is being displayed, you’ll shorten the sleep
time by 10 minutes.
AV receiver
DIMMER
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Functions—Continued
7
Using Headphones
Displaying Source Information
For private listening, you can connect a pair of stereo
headphones (1/4-inch phone plug) to the AV receiver’s
PHONES jack.
You can display various information about the current
input source as follows.
Press the [RECEIVER] REMOTE
MODE button, and then press the
[DISPLAY] button repeatedly to
cycle through the available infor-
mation.
ON/STANDBY
STANDBY
DOCK
MULTI CH
PHONES
A
SPEAKE
Note:
Notes:
• This procedure can also be performed on the AV
receiver by using its [DISPLAY] button.
• Always turn down the volume before connecting your
headphones.
• While the headphones plug is inserted in the PHONES
jack, the speakers set A and B are turned off.
The following information can typically be displayed:
• When you connect a pair of headphones, the listening
mode is set to Stereo, unless it was already set to
Mono, Stereo, or Direct, in which case it stays the
same.
Input source &
1
volume*
2
Signal format*
or sampling
frequency
• When the multichannel DVD input is selected, only
the front left and front right channels can be heard in
the headphones.
Input source &
listening mode
*1 WhenAM or FM radio is used, the band, preset num-
ber, and frequency are displayed.
*2 If the input signal is analog, or AM or FM radio is
selected, no format information is displayed. If the
input signal is PCM, the sampling frequency is dis-
played. If the input signal is digital but not PCM, the
signal format is displayed. Information is displayed
for about 3 seconds, then the previous display reap-
pears.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Functions—Continued
Specifying the Digital Signal Format
The following table shows the display indicator for each
digital signal format.
Format
Dolby Digital
DTS
Display
PCM
PCM
Normally, the AV receiver detects the format of digital
input signals automatically. However, if you experience
either of the following issues when playing PCM or DTS
sources, you can specify the signal format manually.
• If the beginnings of tracks from a PCM source are cut
off, try the PCM setting.
• If noise is produced when fast forwarding or rewind-
ing a DTS CD, try the DTS setting.
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
DIGITAL INPUT
Press and hold the AV receiver’s
[DIGITAL INPUT] button for about
3 seconds.
1
DIGITAL INPUT
While “Auto” is displayed (about
3 seconds), press the [DIGITAL
INPUT] button repeatedly to
select: PCM, DTS, or Auto.
PCM: Only 2-channel PCM format
input signals will be heard. If
the input signal is not PCM,
the PCM indicator will flash
and there will be no sound.
DTS: Only DTS (but not DTS-HD)
format input signals will be
heard. If the input signal is not
DTS, the DTS indicator will
flash and there will be no
2
DIGITAL INPUT
sound.
Auto (default): The format is
detected automatically. If no
digital input signal is present,
the corresponding analog input
is used instead.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
■ Manual Tuning Mode
Listening to AM/FM Stations
Press the [TUNING MODE] button
so that the AUTO indicator disap-
pears from the display.
1
TUNER
TUNING
TUNING MODE
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
PHONES
SETUP MIC
VIDEO
L
AUDIO
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
Press and hold theTUNING Up or
Down [ ]/[ ] button.
LISTENING MODE
2
AV RECEIVER HT-R667
TUNING
The frequency stops changing when
you release the button.
Press the button repeatedly to change
the frequency one step at a time.
TUNING MODE
With the built-in tuner, you can enjoy AM and FM radio
stations and store your favorite stations as presets for
easy selection.
Frequency changes in 0.05MHz steps for FM and 9kHz
(or 10kHz) steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Use the [TUNER] input selector
button to select AM or FM.
In this example, FM has been selected.
TUNER
Band
Frequency
Tuning into Weak FM Stereo Stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
(Actual display depends on country.)
Note:
Note:
• You can also use the remote controller’s [TUNER]
button to select AM or FM.
• You can also use the remote controller’s Up and Down
[
]/[ ] buttons to tune the radio.
Tuning into AM/FM Radio Stations
■ Auto Tuning Mode
Press the [TUNING MODE] button
so that the AUTO indicator
appears on the display.
1
TUNING MODE
Press the TUNING Up or Down
2
[
]/[ ] button.
TUNING
Searching stops when a station is
found.
When tuned into a station, the TUNED indicator
appears. When tuned into a stereo FM station, the FM
STEREO indicator also appears.
FM STEREO
AUTO
TUNED
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune into AM and FM stations directly by enter-
ing the appropriate frequency.
Displaying AM/FM Radio Information
DISPLAY
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
TUNER
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
DISPLAY
Press the [DISPLAY] button to
display the available information.
Band
Frequency
Preset #
Number
buttons
D.TUN
Listening mode
Press the [TUNER] button repeat-
edly to select AM or FM, followed
by the [D.TUN] button.
1
(Actual display depends on country.)
Within 8 seconds, use the num-
2
ber buttons to enter the fre-
quency of the radio station.
For example, to tune to 87.5 (FM),
press 8, 7, 5.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Selecting Presets
Presetting AM/FM Stations
PRESET
2, 4
3
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
MASTER VOLUME
ENTER
TUNING
PRESET
ON/STANDBY
STANDBY
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
ENTER
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AV RECEIVER HT-R667
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
You can store a combination of up to 40 of your favorite
AM and FM radio stations.
CH +/–
Tune into the AM or FM station
1
you want to store as a preset.
Press the [MEMORY] button.
The preset number flashes.
2
MEMORY
PRESET
To select a preset, use the PRE-
SET [ ]/[ ] buttons or the
remote controller’s CH [+/–] but-
ton.
While the preset number is flash-
ing (about 8 seconds), use the
3
PRESET
PRESET [ ]/[ ] buttons to
select a preset from 1 through 40.
You can also use the remote con-
troller’s number buttons to select
a preset directly.
Press the [MEMORY] button
again to store the station.
4
MEMORY
The station is stored and the preset
number stops flashing.
Repeat this procedure for all of your
favorite stations.
Deleting Presets
2
MASTER VOLUME
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
LISTENING MODE
AV RECEIVER HT-R667
Select the preset that you want to
delete.
See the next section.
1
2
While holding down the [MEM-
ORY] button, press the
MEMORY TUNING MODE
[TUNING MODE] button.
The preset is deleted and its number
disappears from the display.
CLEAR
56
Download from Www.Somanuals.com. All Manuals Search And Download.
DS-A1L Dock for the iPod
■ Adjusting the iPod Adapter
About the DS-A1L Dock
The iPod adapter needs to be adjusted to match your par-
ticular iPod. If there’s a gap between the back of your iPod
and the adapter, turn the adapter counterclockwise to close
the gap. Turning the adapter counterclockwise moves it
forward. Turning it clockwise moves it backward.
With the supplied DS-A1L Onkyo Dock, you can easily
play the music stored on yourApple iPod through the AV
receiver and enjoy great sound. You can use the AV
receiver’s remote controller to operate your iPod.
For the latest information on the Dock, see the Onkyo
Web site at: www.onkyo.com
Forward
Backward
iPod adapter
iPod connector
Notes:
• To prevent iPod connector damage, don’t twist your
iPod when inserting or removing it, and be careful
not to knock over the Dock while your iPod is
inserted.
iPod slot
Power indicator
• Don’t use the Dock with any other iPod accesso-
ries, such as FM transmitters and microphones, as
they may cause a malfunction.
Compatible iPod models
Function Overview
■ Made for:
• 5th Generation iPod (iPod with video)
■ Basic Operation
• iPod photo (iPod with color display)
Note:
• 4th Generation iPod
• The AV receiver may take several seconds to star-
tup, so you might not hear the first few seconds of
the first song.
• 2nd Generation iPod nano
• 1st Generation iPod nano
• iPod mini
• System On Function: When you turn on the AV
receiver, the iPod turns on as well.
Note:
• System Off Function: When you turn off the AV
receiver, the iPod turns off as well.
• 3rd generation iPod models are not supported.
• Before using the Dock, update your iPod with the
latest software, available from the Apple Web site
at: www.apple.com
*
• Auto Power On Function : If you start iPod play-
back while the AV receiver is on Standby, the AV
receiver will automatically turn on and select your iPod
as the input source. Then, your iPod will start playback.
*
• Direct Change Function : If you start iPod play-
PuttingYour iPod in the Dock
back while listening to another input source, the AV
receiver will automatically select your iPod as the input
source.
1. Turn on the AV receiver, and select the appropri-
ate inputs on the AV receiver.
2. Align your iPod with the Dock’s iPod slot, and
carefully place your iPod in the slot, as shown.
• Linked Dimmer Operation: When you use the AV
receiver’s Dimmer function to change its display’s
brightness, the brightness of the Dock’s Power indicator
will change as well.
Remove iPod
case before
inserting
• Using the AV receiver’s Remote Controller: You
can use the AV receiver’s remote controller to control
basic iPod functions.
*
If you use your iPod’s controls to start an iPod slideshow or
video, this function will not work, so use the remote controller
instead.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
DS-A1L Dock for the iPod—Continued
Operating Notes:
• Before selecting a different input source, stop iPod
playback to prevent the AV receiver from selecting the
iPod input source by mistake.
• If any accessories are connected to your iPod, the AV
receiver may not be able to select the input source
properly.
• While your iPod is in the Dock, its volume control has
no effect. If you adjust your iPod’s volume control
while it’s in the Dock, make sure it’s not set too high
before you reconnect your headphones.
■ UsingYour iPod’s Alarm Clock
You can use your iPod’s Alarm Clock function to auto-
matically turn on your iPod and the AV receiver at a
specified time. The AV receiver’s input source will auto-
matically be set to the input to which your iPod is con-
nected.
Notes:
• To use this function, your iPod must be in the Dock,
and the Dock must be connected to the AV receiver.
• When you use this function, be sure to set the AV
receiver’s volume control to a suitable level.
• The AV receiver may take several seconds to star-
tup, so you might not hear the first few seconds of
the first song.
■ ChargingYour iPod’s Battery
The Dock charges your iPod’s battery while your iPod is
in the Dock and connected to the DOCK jacks on the AV
receiver. While your iPod is seated in the Dock, its bat-
tery will be charged when the AV receiver is set to On or
Standby.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting with the Remote Controller
Selecting the Listening Modes
For a description of each listening mode, see “About the
Listening Modes” on page 66.
• The Dolby Digital and DTS listening modes
can only be selected if your DVD player is
connected to the AV receiver with a digital
audio connection (coaxial, optical, or HDMI).
STEREO
GAME
MOVIE/TV
MUSIC
• The listening modes you can select depend
on the format of the input signal. To check
the format, see “Displaying Source Informa-
tion” on page 52.
• While a pair of headphones is connected,
you can only select the Mono, Direct, or Ste-
reo listening mode.
• While speaker B is on, you can select only
the Direct or Stereo listening mode.
■ [MOVIE/TV] button
• The listening modes cannot be selected
while speaker set A is off.
This button selects the listening modes intended for
use with movies and TV.
■ [MUSIC] button
This button selects the listening modes intended for
Selecting on the AV Receiver
use with music.
■ [GAME] button
MUSIC
This button selects the listening modes intended for
MASTER VOLUME
use with video games.
TUNING
PRESET
ON/STANDBY
STANDBY
ENTER
■ [STEREO] button
This button selects the Stereo listening mode and All
DOCK
MULTI CH
DVD
VCR/DVR
CBL/SAT
AUX
TAPE
TUNER
CD
SETUP
RETURN
AUX INPUT
AUDIO
PHONES
SETUP MIC
VIDEO
L
R
A
SPEAKERS
B
TONE
MOVIE/TV
MUSIC
GAME
DISPLAY DIGITAL INPUT
DIMMER MEMORY TUNING MODE
CLEAR
channel Stereo listening mode.
LISTENING MODE
AV RECEIVER HT-R667
GAME
MOVIE/TV
■ [MOVIE/TV] button
This button selects the listening modes intended for
use with movies and TV.
■ [MUSIC] button
This button selects the listening modes intended for
use with music.
■ [GAME] button
This button selects the listening modes intended for
use with video games.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Listening Modes Available for Each Source Format
Analog and PCM Sources
PCM
Multi
Multichannel
32–96kHz*1
2ch
176.4/192kHz*2
Source format
32–96
176.4/ channel
Analog
Multi-
channel
Mono/
Multi-
Mono/
kHz*1 192kHz*2
2ch
Multiplex channel
Multiplex
Media
CD, TV, radio,
DVD
DVD
DVD
Button
Listening Mode
Mono
✔
✔
✔
✔
✔
Multichannel
Neo:6
✔
*4
✔
Dolby PLII Movie/
Dolby PLIIx Movie*3
*4
✔
✔
✔
*4
DolbyEX
✔
[MOVIE/
TV]
Neo:6 Cinema
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
MonoMovie*5 *6
TV Logic*5 *6
AllChStereo
FullMono
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
T-D *6
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
Multichannel
*4
Neo:6
✔
Dolby PLII Music/
Dolby PLIIx Music*3
*4
✔
✔
✔
*4
DolbyEX
✔
[MUSIC]
Neo:6 Music
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Orchestra*5 *6
Unplugged*5 *6
Studio-Mix*5 *6
AllChStereo
FullMono
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Multichannel
✔
✔
*4
Neo:6
✔
Dolby PLII Game/
Dolby PLIIx Game*3
✔
✔
[GAME]
*4
DolbyEX
✔
AllChStereo
FullMono
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
T-D *6
AllChStereo
Stereo
[STEREO]
✔
✔
✔
✔
*1. 32/44,1/48/88.2/96kHz
*2. DVD-Audio discs output multichannel 176.4/192kHz PCM only via HDMI.
*3. If there are no surround back speakers, Dolby Pro Logic II is used.
*4. Cannot be selected with some source formats.
*5. Available only when using surround speakers.
*6. PCM of 64kHz, 88.2kHz, and 96kHz are processed at 32kHz, 44.1kHz, and 48kHz respectively.
Requires 6.1/7.1 speakers.
Requires 7.1 speakers.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Dolby Digital and Dolby Digital Plus Sources
Dolby Digital
Dolby Digital Plus
Source format
Media
Mono/
Multiplex
Mono/
Multiplex
Multichannel
2ch
Multichannel
2ch
DVD, DTV, etc.
Blu-ray, HD DVD
Button
Listening Mode
Mono
✔
✔
✔
✔
✔
✔
✔
DolbyDigital
*1
*3
*3
*3
DolbyDigital Plus
✔
✔
✔
✔
*3
Neo:6
✔
✔
✔
*3
Dolby PLII Movie/Dolby PLIIx Movie*2
DolbyEX
✔
✔
✔
*3
[MOVIE/TV]
Neo:6 Cinema
✔
✔
✔
✔
✔
✔
✔
✔
MonoMovie*4
TV Logic*4
AllChStereo
FullMono
T-D
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Direct
✔
✔
✔
✔
✔
✔
Stereo
DolbyDigital
*1
DolbyDigital Plus
✔
✔
✔
✔
*3
*3
*3
*3
Neo:6
✔
✔
✔
*3
*3
Dolby PLII Music/Dolby PLIIx Music*2
DolbyEX
✔
✔
✔
[MUSIC]
Neo:6 Music
✔
✔
✔
✔
✔
✔
Orchestra*4
Unplugged*4
Studio-Mix*4
AllChStereo
FullMono
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DolbyDigital
*1
DolbyDigital Plus
✔
✔
*3
*3
Neo:6
✔
Dolby PLII Game/Dolby PLIIx Game*2
✔
✔
[GAME]
*3
*3
DolbyEX
AllChStereo
FullMono
T-D
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
AllChStereo
Stereo
✔
✔
✔
✔
✔
✔
[STEREO]
*1. If there are no surround back speakers, depending on the input signal, Dolby Digital may be used.
*2. If there are no surround back speakers, Dolby Pro Logic II is used.
*3. Cannot be selected with some source formats.
*4. Available only when using surround speakers.
Requires 6.1/7.1 speakers.
Requires 7.1 speakers.
Note:
• With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format
changes during playback. It is not a malfunction.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
DTS Sources
DTS, DTS 96/24
2ch
DTS
Discrete/Matrix
Source format
Multichannel
Mono
Media
DVD, CD, etc.
DVD, CD, etc.
Button
Listening Mode
Mono
✔
✔
✔
✔
✔
✔
DTS, DTS 96/24
*1
DTS-ES Discrete/Matrix
Neo:6
✔
*3
✔
✔
*3
Dolby PLII Movie/Dolby PLIIx Movie*2
DolbyEX
✔
*3
✔
[MOVIE/TV]
Neo:6 Cinema
✔
✔
✔
✔
✔
✔
✔
✔
MonoMovie*4 *5
TV Logic*4 *5
AllChStereo
FullMono
T-D*5
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Direct
Stereo
DTS, DTS 96/24
*1
DTS-ES Discrete/Matrix
✔
*3
Neo:6
✔
✔
✔
Dolby PLII Music/Dolby PLIIx Music*2
*3
*3
✔
[MUSIC]
DolbyEX
Neo:6 Music
✔
✔
✔
✔
✔
✔
Orchestra*4 *5
Unplugged*4 *5
Studio-Mix*4 *5
AllChStereo
FullMono
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DTS, DTS 96/24
*1
DTS-ES Discrete/Matrix
Neo:6
✔
*3
✔
Dolby PLII Game/Dolby PLIIx Game*2
✔
[GAME]
*3
DolbyEX
AllChStereo
FullMono
T-D*5
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
AllChStereo
Stereo
[STEREO]
*1. If there are no surround back speakers, DTS is used.
*2. If there are no surround back speakers, Dolby Pro Logic II is used.
*3. Cannot be selected with some source formats.
*4. Available only when using surround speakers.
*5. DTS 96/24 is processed as DTS.
Requires 6.1/7.1 speakers.
Requires 7.1 speakers.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
TrueHD Sources
TrueHD
2ch
TrueHD 192kHz
Source format
Mono/
Multiplex
Mono/
Multichannel
Multichannel
2ch
Multiplex
Media
Blu-ray, HD DVD
Blu-ray, HD DVD
Button
Listening Mode
Mono
✔
✔
✔
✔
TrueHD
✔
*2
Neo:6
✔
✔
✔
*2
*2
Dolby PLII Movie/Dolby PLIIx Movie*1
✔
[MOVIE/TV]
DolbyEX
Neo:6 Cinema
✔
✔
✔
✔
✔
AllChStereo
✔
✔
✔
✔
✔
FullMono
✔
✔
✔
✔
Direct
✔
✔
✔
✔
✔
✔
✔
Stereo
TrueHD
*2
Neo:6
✔
✔
✔
*2
*2
[MUSIC]
Dolby PLII Music/Dolby PLIIx Music*1
✔
DolbyEX
Neo:6 Music
AllChStereo
FullMono
TrueHD
✔
✔
✔
✔
✔
✔
✔
✔
✔
*2
Neo:6
✔
Dolby PLII Game/Dolby PLIIx Game*1
✔
[GAME]
*2
DolbyEX
✔
AllChStereo
FullMono
AllChStereo
Stereo
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
[STEREO]
✔
✔
✔
*1. If there are no surround back speakers, Dolby Pro Logic II is used.
*2. Cannot be selected with some source formats.
Requires 6.1/7.1 speakers.
Requires 7.1 speakers.
Note:
• With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format
changes during playback. It is not a malfunction.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
DTS-HD Sources
DTS-HD Master Audio*1
DTS-HD High Resolution
Multichannel 2ch Mono Multichannel
Source format
2ch
Mono
Media
Blu-ray, HD DVD
Blu-ray, HD DVD
Button
Listening Mode
Mono
✔
✔
✔
✔
✔
✔
✔
✔
DTS-HD High Resolution
DTS-HD Master Audio
Neo:6
*3
*3
✔
✔
✔
✔
✔
✔
*3
*3
*3
*3
Dolby PLII Movie/Dolby PLIIx Movie*2
DolbyEX
[MOVIE/TV]
✔
✔
Neo:6 Cinema
AllChStereo
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
FullMono
✔
✔
✔
✔
✔
✔
✔
Direct
Stereo
DTS-HD High Resolution
DTS-HD Master Audio
Neo:6
✔
*3
*3
✔
✔
✔
✔
✔
✔
[MUSIC]
Dolby PLII Music/Dolby PLIIx Music*2
*3
*3
*3
*3
✔
✔
DolbyEX
Neo:6 Music
✔
✔
✔
✔
✔
✔
AllChStereo
✔
✔
✔
✔
✔
✔
FullMono
✔
✔
✔
DTS-HD High Resolution
DTS-HD Master Audio
Neo:6
✔
*3
*3
✔
✔
✔
Dolby PLII Game/Dolby PLIIx Game*2
[GAME]
✔
✔
*3
*3
DolbyEX
✔
AllChStereo
FullMono
AllChStereo
Stereo
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
[STEREO]
*1. 192kHz DTS-HD Master Audio sources are processed at 96kHz.
*2. If there are no surround back speakers, Dolby Pro Logic II is used.
*3. Cannot be selected with some source formats.
Requires 6.1/7.1 speakers.
Requires 7.1 speakers.
Note:
• With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format
changes during playback. It is not a malfunction.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
DTS Express and DSD Sources
DSD*1
Multichannel
DTS Express
Source format
Media
Multichannel
2ch
Mono
2ch
(3/2.1)
Blu-ray, HD DVD
SACD
Button
Listening Mode
Mono
✔
✔
✔
✔
✔
✔
DTS Express
DSD
✔
✔
✔
✔
*3
Neo:6
✔
✔
✔
*3
*3
Dolby PLII Movie/Dolby PLIIx Movie*2
DolbyEX
✔
✔
✔
[MOVIE/TV]
Neo:6 Cinema
✔
✔
✔
✔
✔
✔
✔
✔
MonoMovie*4
TV Logic*4
AllChStereo
FullMono
T-D
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Direct
✔
✔
✔
✔
✔
✔
✔
✔
✔
Stereo
DTS Express
DSD
✔
✔
✔
✔
*3
Neo:6
✔
✔
✔
Dolby PLII Music/Dolby PLIIx Music*2
*3
*3
✔
✔
✔
[MUSIC]
DolbyEX
Neo:6 Music
✔
✔
✔
✔
✔
✔
Orchestra*4
Unplugged*4
Studio-Mix*4
AllChStereo
FullMono
DTS Express
DSD
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Neo:6
Dolby PLII Game/Dolby PLIIx Game*2
✔
✔
[GAME]
DolbyEX
AllChStereo
FullMono
T-D
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
AllChStereo
Stereo
✔
✔
✔
✔
✔
✔
✔
✔
[STEREO]
*1. DSD signals are processed after conversion to PCM.
*2. If there are no surround back speakers, Dolby Pro Logic II is used.
*3. Cannot be selected with some source formats.
*4. Available only when using surround speakers.
If you can select PCM or DSD output on your SACD player, in some cases, selecting PCM will
provide the best sound quality.
Hint!
Note:
• With some HD DVD and Blu-ray discs, a noise may be heard during playback. This may occur when the audio format
changes during playback. It is not a malfunction.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
Dolby Digital
About the Listening Modes
Use this mode with DVDs that bear the Dolby Digital
logo, and Dolby Digital TV broadcasts. This is the most
common digital surround-sound format, and it’ll put you
right in the middle of the action, just like being in a
movie theater or concert hall.
The AV receiver’s listening modes can transform your
listening room into a movie theater or concert hall, with
high fidelity and stunning surround sound.
The illustration shows which speakers are active in
each listening mode with 7.1 channel speaker sys-
tem.
5.1-channel source + Dolby EX
These modes expand 5.1-channel sources for 6.1/7.1-
channel playback. They’re especially suited to Dolby EX
soundtracks that include a matrix-encoded surround
back channel. The additional channel adds an extra
dimension and provides an enveloping surround sound
experience, perfect for rotating and fly-by sound effects.
Front left
Center
Front right
Subwoofer
Surround left
Surround
Surround right
back left/ right
5.1-channel source + Dolby PLIIx Music
These modes use the Dolby Pro Logic IIx Music mode
to expand 5.1-channel sources for 6.1/7.1-channel play-
back.
Direct
In this mode, audio from the input source is output
directly with minimal processing, providing high-fidel-
ity reproduction. All of the source’s audio channels are
output as they are.
5.1-channel source + Dolby PLIIx Movie
These modes use the Dolby Pro Logic IIx Movie mode
to expand 5.1-channel sources for 7.1-channel playback.
Stereo
Sound is output by the front left and right speakers and
subwoofer.
Dolby Digital Plus
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest mul-
tichannel audio format from Dolby. It supports up to 7.1
channels with 48kHz sampling rate.
Mono
Use this mode when watching an old movie with a mono
soundtrack, or use it with the foreign language
soundtracks recorded in the left and right channels of
some movies. It can also be used with DVDs or other
sources containing multiplexed audio, such as karaoke
DVDs.
Dolby TrueHD
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc for-
mats, this new Dolby format offers up to 7.1 discrete
channels of digital audio with 48/96 kHz, up to 5.1-chan-
nels with 192 kHz sampling rate.
Dolby Pro Logic IIx
Dolby Pro Logic II
For the signals supported by the AV receiver, see
page 63.
Dolby Pro Logic IIx expands any 2-channel source for
7.1-channel playback. It provides a very natural and
seamless surround-sound experience that fully envelops
the listener. As well as music and movies, video games
can also benefit from the dramatic spatial effects and
vivid imaging. If you’re not using any surround back
speakers, Dolby Pro Logic II will be used instead of
Dolby Pro Logic IIx.
DTS
The DTS digital surround-sound format supports up to
5.1 discrete channels and uses less compression for high-
fidelity reproduction. Use it with DVDs and CDs that
bear the DTS logo.
DTS 96/24
•
Dolby PLIIx Movie
This mode is for use with DTS 96/24 sources. This is
high-resolution DTS with a 96kHz sampling rate and 24-
bit resolution, providing superior fidelity. Use it with
DVDs that bear the DTS 96/24 logo.
Use this mode with any stereo or Dolby Surround
(Pro Logic) movie (e.g., TV, DVD, VHS).
•
Dolby PLIIx Music
Use this mode with any stereo or Dolby Surround
(Pro Logic) music source (e.g., CD, radio, cassette,
TV, VHS, DVD).
•
Dolby PLIIx Game
Use this mode with video games, especially those
that bear the Dolby Pro Logic II logo.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Listening Modes—Continued
DSD
DTS-ES Discrete
DSD stands for Direct Stream Digital and is the format
used to store digital audio on Super Audio CDs (SACD).
This mode can be used with SACDs that feature multi-
channel audio.
This mode is for use with DTS-ES Discrete soundtracks,
that use a discrete surround back channel for true
6.1/7.1-channel playback. The seven totally separate
audio channels provide better spatial imaging and 360-
degree sound localization, perfect for sounds that pan
across the surround channels. Use it with DVDs that bear
the DTS-ES logo, especially those with a DTS-ES Dis-
crete soundtrack.
Onkyo Original DSP Modes
Mono Movie
This mode is suitable for old movies and other mono
sources. The center speaker outputs the sound as it is,
while reverb is applied to the sound output by the other
speakers, giving presence to even mono material.
DTS-ES Matrix
This mode is for use with DTS-ES Matrix soundtracks,
that use a matrix-encoded back-channel for 6.1/7.1-
channel playback. Use it with DVDs that bear the DTS-
ES logo, especially those with a DTS-ES Matrix
soundtrack.
Orchestra
Suitable for classical or operatic music, this mode
emphasizes the surround channels in order to widen the
stereo image and simulates the natural reverberation of a
large hall.
DTS Neo:6
This mode expands any 2-channel source for 7.1-chan-
nel playback. It uses seven full-bandwidth channels of
matrix decoding for matrix-encoded material, providing
a very natural and seamless surround sound experience
that fully envelops the listener.
Unplugged
Suitable for acoustic instruments, vocals, and jazz, this
mode emphasizes the front stereo image, giving the
impression of being right in front of the stage.
•
Neo:6 Cinema
Use this mode with any stereo movie (e.g., TV,
DVD, VHS).
Studio-Mix
Suitable for rock or pop music, listening to music in this
mode creates a lively sound field with a powerful acous-
tic image, like being at a club or rock concert.
•
Neo:6 Music
Use this mode with any stereo music source (e.g.,
CD, radio, cassette, TV, VHS, DVD).
TV Logic
5.1-channel source + Neo:6
This mode adds realistic acoustics to TV shows pro-
duced in a TV studio, surround effects to the entire
sound, and clarity to voices.
This mode uses Neo:6 to expand 5.1-channel sources for
6.1/7.1-channel playback.
DTS-HD High Resolution Audio
All Ch Stereo
Developed for use with HDTV, including the new video
disc formats Blu-ray and HD DVD, this is the latest mul-
tichannel audio format from DTS. It supports up to 7.1
channels with 96 kHz sampling rate.
Ideal for background music, this mode fills the entire lis-
tening area with stereo sound from the front, surround,
and surround back speakers.
DTS-HD Master Audio
Full Mono
Designed to take full advantage of the additional storage
space offered by the new Blu-ray and HD DVD disc for-
mats, this new DTS format offers up to 7.1 discrete chan-
nels of digital audio with 48/96 kHz, up to 5.1-channels
with 192 kHz sampling rate.
In this mode, all speakers output the same sound in
mono, so the sound you hear is the same regardless of
where you are within the listening room.
T-D (Theater-Dimensional)
or
With this mode you can enjoy a virtual 5.1 surround
sound even with only two or three speakers. This works
by controlling how sounds reach the listener’s left and
right ears. Good results may not be possible if there’s too
much reverb, so we recommend that you use this mode
in an environment with little or no natural reverb.
For the signals supported by the AV receiver, see
page 64.
DTS Express
This format supports up to 5.1 channels and a lower sam-
pling rate of 48 kHz. Applications include interactive
audio and commentary encoding for HD DVD Sub
Audio and Blu-ray SecondaryAudio.Also broadcast and
media servers.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
This section explains how to record the input source and
how to record audio and video from separate sources.
Recording from Different AV Sources
You can overdub audio onto your video recordings by
simultaneously recording audio and video from two sep-
arate sources. This is possible because only the audio
source is switched when an audio-only input source,
such as TAPE, TUNER, or CD, is selected, the video
source remains the same.
In the following example, audio from the CD player con-
nected to the CD IN and video from the camcorder con-
nected to the AUX INPUT VIDEO jack are recorded by
the VCR connected to the VCR/DVR OUT jacks.
Notes:
• The surround sound and DSP listening modes cannot
be recorded.
• Copy-protected DVDs cannot be recorded.
• Sources connected to the multichannel DVD input
cannot be recorded.
• Sources connected to a digital input cannot be
recorded. Only analog inputs can be recorded.
• DTS signals will be recorded as noise, so don’t
attempt analog recording of DTS CDs or LDs.
AUX INPUT
VIDEO
L
AUDIO
R
Recording the Input Source
Audio sources can be recorded to a recorder (e.g., cas-
sette deck, CDR, MD) connected to the TAPE OUT jack.
Video sources can be recorded to a video recorder (e.g.,
VCR, DVR) connected to the VCR/DVR OUT jacks.
Camcorder
video signal
audio signal
Use the input selector buttons to
select the source that you want
to record.
VCR/DVR CBL/SAT
1
HDMI
ASSIGNABLE
IN
4
IN
3
(CBL/SAT)
IN
2
(VCR/DVR)
IN
1
(DVD)
OUT
DIGITAL IN
1
COMPONENT VIDEO
DVD
Y
DOCK
(for DS-A1L)
AM
(DVD)
See “Which Connections Should I
Use?” on page 27 to see which signals
can be output and recorded.
MONITOR
OUT
COAXIAL
CBL/SAT
VCR/DVR
DVD
CB/PB
2
V
S
(CBL/SAT)
V
S
ANTENNA
CR/PR
AUX
CD
TAPE
TUNER
FM
75
1
(VCR/DVR)
OPTICAL
IN
2
(CBL/SAT) IN 1(DVD)
ASSIGNABLE
OUT
OUT
IN
IN
OUT
OUT
IN
IN
IN
2
(CD)
IN
IN
FRONT
SURR
CENTER
SURR BACK
ASSIGNABLE
L
L
L
You can watch the source while record-
ing it. The AV receiver’s MASTER
VOLUME control has no effect on
recording.
R
R
R
REMOTE
SUB
CONTROL
WOOFER
Remote
controller
DVD
CD
TAPE
CBL/SAT
VCR/DVR
CD player
VCR
Prepare the camcorder and CD player for
playback.
1
On your recorder, start record-
ing.
2
3
Prepare the VCR for recording.
2
3
4
On the source component, start
playback.
Press the [AUX] input selector button.
Press the [CD] input selector button.
This selects the CD player as the audio source but
leaves the camcorder as the video source.
Note:
• If you select a different input source during recording,
that input source will be recorded instead.
Start recording on the VCR, then start
playback on the camcorder and CD player.
Video from the camcorder and audio from the CD
player are recorded by the VCR.
5
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes
The Audio Adjust settings are explained below.
Using the Audio Adjust Settings
Multiplex/Mono Settings
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
■ Input Ch
1
This setting determines which channel of a stereo multi-
plex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV
broadcasts, and so on.
Main: The main channel is output (default).
Sub: The sub channel is output.
Main/Sub: Both the main and sub channels are out-
put.
Use the Up and Down [ ]/[
buttons to select “3. Audio
]
2
3
Mono
■ Input Ch
Adjust,” and then press [ENTER].
This setting determines which channel is output when
the Mono listening mode is used with a stereo source.
Left+Right: Both the left and right channels are output
(default).
Left: Only the left channel is output.
Right: Only the right channel is output.
Use the Up and Down [ ]/[
]
PLIIx/Neo:6 Settings
buttons to select an item, and
then press [ENTER].
PLIIx Music (2 ch Input)
These settings apply to only 2-channel stereo sources.
3. Audio Adjust
If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro
Logic IIx.
1. Multiplex/Mono
2. PLIIx/Neo:6
3. Dolby EX
4. Theater-Dimensional
■ Panorama
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
On: Panorama function on.
Off: Panorama function off (default).
Use the Up and Down [ ]/[
buttons to select an option, and
use the Left and Right [ ]/[
buttons to change it.
The Audio Adjust menu items are
explained below.
]
4
5
■ Dimension
]
With this setting, you can move the sound field forward
or backward when using the Dolby Pro Logic IIx Music
listening mode. It can be adjusted from –3 to +3. The
default value is 0. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
When you’ve finished, press the
[SETUP] button.
Setup closes.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes—Continued
■ Center Width
Dolby EX Settings
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you’re using a
center speaker, the center channel sound is output by
only the center speaker. (If you’re not using a center
speaker, the center channel sound will be distributed to
the front left and right speakers to create a phantom cen-
ter). This setting controls the front left, right, and center
mix, allowing you to adjust the weight of the center
channel sound. It can be adjusted from 0 to 7. The default
value is 3.
■ Dolby EX
This setting determines how Dolby EX signals are han-
dled.
Auto: When the source is Dolby EX, you can select
the Dolby EX listening mode.
Manual:When the source is Dolby EX, you can select
any of the listening modes compatible with this
format (e.g., Dolby EX, Dolby Pro Logic IIx,
etc.).
Neo:6 Music
Theater-Dimensional Setting
■ Center Image
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel stereo sources. With this
setting, you can specify by how much the front left and
right channel output is attenuated in order to create the
center channel. It can be adjusted from 0 to 5. The
default value is 2.
■ Listening Angle
With this setting, you can optimize the Theater-Dimen-
sional listening mode by specifying the angle of the front
left and right speakers relative to the listening position.
Ideally, the front left and right speakers should be equi-
distant from the listening position and at an angle close
to one of the two available settings.
When set to 0, the front left and right channel output is
attenuated by half (–6 dB), giving the impression that the
sound is located centrally. This setting works well when
the listening position is considerably off center. When
set to 5, the front left and right channels are not attenu-
ated, maintaining the original stereo balance.
Front left speaker
Front right speaker
20˚/40˚
Narrow: Select if the listening angle is 20 degrees.
Wide: Select if the listening angle is 40 degrees
(default).
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes—Continued
Late Night Function
Using the Audio Settings
You can change various audio settings by pressing the
[AUDIO] button.
■ Late Night
With the Late Night function, you can reduce the
dynamic range of Dolby Digital material so that you can
still hear quiet parts even when listening at low volume
levels—ideal for watching movies late at night when you
don’t want to disturb anyone.
Note:
• When theAudio TV Out setting is set to On (page 82),
the [AUDIO] button is disabled.
Press the [RECEIVER] button fol-
lowed by the [AUDIO] button.
For Dolby Digital and Dolby Digital Plus sources, the
options are:
1
Off: Late Night function off (default).
Low: Small reduction in dynamic range.
High: Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
Auto: The Late Night function is set to On or Off
automatically (default).
Off: Late Night function off.
On: Late Night function on.
Use the Up and Down [ ]/[
buttons to select an item.
]
2
3
Notes:
• The Late Night function can be used only when the
input source is Dolby Digital, Dolby Digital Plus, or
Dolby TrueHD.
• The effect of the Late Night function depends on the
material that you are playing and the intention of the
original sound designer, and with some material there
will be little or no effect when you select the different
options.
Use the Left and Right [ ]/[
buttons to change the setting.
Repeat this step for the other settings.
]
• The Late Night function is set to Off when the AV
receiver is set to Standby. For Dolby TrueHD sources,
it will be set to Auto.
CinemaFILTER
The Audio Adjust settings are explained below.
■ Cinema Fltr
Tone Control Settings
With the CinemaFILTER, you can soften overly bright
movie soundtracks, which are typically mixed for repro-
duction in a movie theater.
You can adjust the bass and treble for the front speakers,
except when the Direct listening mode is selected.
CinemaFILTER can be used with the following listening
modes: Dolby Digital, Dolby Digital EX, Dolby Pro
Logic IIx Movie, Dolby Pro Logic II Movie, DTS, DTS-
ES, DTS Neo:6 Cinema, DTS 96/24, and Neo:6.
Off: CinemaFILTER off.
■ Bass
You can boost or cut low-frequency sounds output by the
front speakers from –10 dB to +10 dB in 2 dB steps.
■ Treble
On: CinemaFILTER on.
You can boost or cut high-frequency sounds output by
the front speakers from –10 dB to +10 dB in 2 dB steps.
Note:
Notes:
• The CinemaFILTER may not work when used with
certain input sources.
• To bypass the bass and treble tone circuits, select the
Direct listening mode.
• This procedure can also be performed on the AV
receiver by using its [TONE], [–], and [+] buttons.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes—Continued
®
Audyssey Dynamic EQ
Speaker Levels
You can adjust the volume of each speaker while listen-
ing to an input source.
These temporary adjustments are cancelled when theAV
receiver is set to Standby.
■ DynamicEQ
WithAudyssey Dynamic EQ, you can enjoy great sound
even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of deteriorat-
ing sound quality as volume is decreased by taking into
account human perception and room acoustics.
■ Subwfr (Subwoofer)
You can adjust the level from –15 dB to +12 dB.
It does so by selecting the correct frequency response
and surround volume levels moment-by-moment so that
the content sounds the way it was created at any volume
level--not just at reference level.
■ Center
You can adjust the level from –12 dB to +12 dB.
Notes:
• You cannot use this function while the AV receiver is
muted.
Off: Audyssey Dynamic EQ off.
On: Audyssey Dynamic EQ on.
• Speakers that are set to No or None in the Speaker
Configuration cannot be adjusted (see page 74).
Note:
• Audyssey Dynamic EQ can be set only when the
Equalizer Settings on page 78 are set to Audyssey.
• This setting is not available when the Direct listening
mode is used with an analog input signal.
Music Optimizer
A/V Sync
■ M.Optimizer
■ A/V Sync
The Music Optimizer function enhances the sound qual-
ity of compressed music files. Use it with music files that
use “lossy” compression, such as MP3.
When using progressive scanning on your DVD player,
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it from 0 to 100 milliseconds
(ms) in 20 millisecond steps.
Off: Music Optimizer off (default).
On: Music Optimizer on.
Note:
• The Music Optimizer function only works with PCM
digital audio input signals with a sampling rate below
48kHz and analog audio input signals. The Music
Optimizer is disabled when the Direct listening mode
is selected.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Listening Modes—Continued
Listening Mode Presets
Use the Up and Down [ ]/[
buttons to select an audio for-
]
4
On the Listening Mode Preset menu, you can specify a
default listening mode for each of the audio formats sup-
ported by each input selector. The AV receiver will then
select the listening mode automatically depending on the
format of the input signal. You can still select the other
listening modes, although the default listening mode will
be used the next time you turn on the AV receiver.
[
]/[ ] buttons to select a lis-
tening mode.
Only listening modes compatible with
the audio format can be selected (see
pages 60–65).
Analog/PCM: Specifies the default lis-
tening mode for analog and PCM
sources.
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
1
Dolby Digital: Specifies the default lis-
tening mode for Dolby Digital sources.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
DTS: Specifies the default listening
mode for DTS sources.
D.F. 2ch: Specifies the default listening
mode for 2-channel (2/0) stereo sources
in a digital format, such as Dolby Digi-
tal or DTS.
Use the Up and Down [ ]/[
]
2
3
D.F. Mono: Specifies the default listen-
ing mode for mono sources in a digital
format, such as Dolby Digital or DTS.
buttons to select “5. Listening
Mode Preset,” and then press
[ENTER].
Multich PCM: Specifies the default
listening mode for multichannel PCM
sources, such as DVD-Audio (input via
HDMI).
192k/176.4k: Specifies the default lis-
tening mode for high resolution
192kHz and 176.4kHz digital sources,
such as DVD-Audio.
Dolby TrueHD: Specifies the default
listening mode for Dolby TrueHD
sources, such as Blu-ray or HD DVD
(input via HDMI).
Use the Up and Down [ ]/[
buttons to select an input selec-
tor, and then press [ENTER].
The audio formats supported by that
input selector appear.
]
DTS-HD Master Audio: Specifies the
default listening mode for DTS-HD
Master Audio sources, such as Blu-ray
or HD DVD (input via HDMI).
For the TUNER input selector, Analog
is the only format available.
DSD: Specifies the default listening
mode for DSD multichannel sources,
such as SACD.
When you’ve finished, press the
[SETUP] button.
5
Setup closes.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup
Speaker Setup
Use the Up and Down [ ]/[
buttons to select “1. Speaker
Configuration,” and then press
the [ENTER] button.
]
3
This section explains how to check the speaker settings
and how to set them manually, which is useful if you
change a speaker after performing the automatic speaker
setup.
Some of the speaker settings are set automatically by the
Automatic Speaker Setup function (see page 42).
Speaker Configuration, Crossover Frequency,
and Double Bass settings only need to be
changed if you’re not using the speakers in
this package.
These settings cannot be changed while head-
phones are connected, speaker set B is on, or
the multichannel DVD input is being used.
While the “Subwoofer” setting is
selected, use the Left and Right
4
5
[
]/[ ] buttons to select Yes or
No.
Yes: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
Speaker Configuration
nected.
These settings are set automatically by the Automatic
Speaker Setup function (see page 42).
Use the Down [ ] button to
select “Front,” and then use the
Left and Right [ ]/[ ] buttons to
select Small or Large.
Small: Select if the front speakers are
small.
This section explains how to specify which speakers are
connected and their sizes.
For speakers with a cone diameter
larger than 6-1/2 inches, specify
Large (full band). For those with a
smaller diameter, specify Small
(default crossover 100Hz).
Large: Select if the front speakers are
large.
Note:
• If the Subwoofer setting in step 4 is
set to No, this setting is fixed at Large
and does not appear.
The crossover frequency can be
changed on page 75.
Cone diameter
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the composite video or S-Video MONITOR OUT,
or the COMPONENT VIDEO OUT, use the HT-
R667’s own display when changing settings.
Use the Down [ ] button to
select “Center,” and then use the
Left and Right [ ]/[ ] buttons to
select Small, Large, or None.
Small: Select if the center speaker is
small.
6
Press the [RECEIVER] button fol-
1
large.
lowed by the [SETUP] button.
None: Select if no center speaker is
connected.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press the
[ENTER] button.
]
2
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Crossover Frequency
Use the Down [ ] button to
7
select “Surround,” and then use
the Left and Right [ ]/[ ] but-
tons to select Small, Large, or
None.
Small: Select if the surround speak-
ers are small.
ers are large.
None: Select if no surround speakers
are connected.
This setting is set automatically by the Automatic
Speaker Setup function (see page 42).
This setting only applies to the speakers that you speci-
fied as Small in the “Speaker Configuration” on page 74.
To get the best bass performance from your speaker sys-
tem, you need to set the crossover frequency according
to the size and frequency response of your speakers
Use the Down [ ] button to
10
select “Crossover,” and then use
the Left and Right [ ]/[ ] but-
tons to select a crossover fre-
quency.
Note:
• If the Front setting in step 5 is set to
Small, the Large option cannot be
selected.
Use the diameter of the smallest
speaker in your system when choosing
the crossover frequency.
Use the Down [ ] button to
8
select “Surr Back,” and use the
Left and Right [ ]/[ ] buttons to
select Small, Large, or None.
Small: Select if the surround back
speakers are small.
Speaker cone
diameter
Crossover
frequency
Over 8 in.
40/50/60Hz*
80Hz
Large: Select if the surround back
speakers are large.
6-1/2 to 8 in.
5-1/4 to 6-1/2 in. 100Hz (default)
None: Select if no surround back
speakers are connected.
3-1/2 to 5-1/4 in.
Under 3-1/2 in.
120Hz
Notes:
150/200Hz*
• If the Surround setting in step 7 is set
to None, this setting does not appear.
• If the Surround setting in step 7 is set
to Small, the Large option cannot be
selected.
*Choose the setting suitable for the speaker.
Continue with step 11 of the “Double
Bass” setting on the next page.
Notes:
Use the Down [ ] button to
9
• For a more accurate setting, look up the frequency
response in the manuals supplied with your speakers
and set accordingly.
select “Surr Back ch,” and use
the Left and Right [ ]/[ ] but-
tons to select 2ch or 1ch.
2ch: Select if two (left and right)
surround back speakers are
connected.
• Choose a higher crossover frequency if you want more
sound from your subwoofer.
• These settings cannot be changed while headphones
are connected or the multichannel DVD input is being
used.
1ch: Select if one surround back
speaker is connected.
Note:
• If the Surround or Surr Back settings
in steps 7 and 9 are set to None, this
setting does not appear.
Continue with step 10 of the “Cross-
over Frequency” setting.
Note:
• These settings cannot be changed while headphones
are connected or the multichannel DVD input is being
used.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Double Bass
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
3
This setting is not set automatically by theAutomatic
Speaker Setup function (see page 42).
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer. This function can be
set only if the Subwoofer setting (step 4) is set to Yes,
and the Front setting (step 5) is set to Large in the
Speaker Configuration on page 74.
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press the
[ENTER] button.
]
Use the Down [ ] button to
select “Double Bass,” and then
11
use the Left and Right [ ]/[
buttons to select:
]
On: Double Bass function on.
Bass from the front left and
right channels is also fed to
the subwoofer (default).
Off: Double Bass function off.
Use the Up and Down [ ]/[
buttons to select“2. Speaker Dis-
tance,” and then press [ENTER].
]
4
5
Press the [SETUP] button.
Setup closes.
12
Note:
• These settings cannot be changed while headphones
are connected, speaker set B is on, or the multichannel
DVD input is being used.
While“Unit”is displayed, use the
Left and Right [ ]/[ ] buttons to
select “feet” or “meters”.
feet: Distances can be set in feet.
Range: 1 to 30 feet in 1-foot
steps.
Speaker Distance
meters: Distances can be set in
meters. Range: 0.3 to 9
meters in 0.3-meter steps.
These settings are set automatically by the Automatic
Speaker Setup function (see page 42).
With these settings, you can specify the distance from
each speaker to the listening position.
Use the Down [ ] button to
6
7
select“Left”and use the Left and
Right [ ]/[ ] buttons to specify
the distance for the front speak-
ers, then press the Down [ ] but-
ton to select the next speaker.
Measure and make a note of the
1
distance from each speaker to
the listening position.
Repeat step 6 for all speakers.
Note:
Speakers that you set to No or None in
the Speaker Configuration (page 74)
cannot be selected.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Press the [SETUP] button.
Setup closes.
Use the Up and Down [ ]/[
]
8
3
buttons to select “3. Level Cali-
bration,” and then press
[ENTER].
A pink noise test tone is output by the
front left speaker.
Notes:
• The Center and Subwoofer distances can be set up to
5 ft. (1.5 m) more or less than the Left distance. For
example, if the Left distance is set to 20 ft. (6 m), the
Center and Subwoofer distances can be set between 15
and 25 ft. (4.5 and 7.5 m).
Turn up the volume so that you
can hear the test tone suffi-
ciently.
As each speaker outputs the test tone,
its name appears on the display.
• The Surround and Surround Back distances can be set
up to 5 ft. (1.5 m) more or 15 ft. (4.5 m) less than the
Left distance. For example, if the Left distance is set
to 20 ft. (6 m), the SurrRight, Surr Left, Surr Back R,
and Surr Back L distances can be set between 5 and 25
ft. (1.5 and 7.5 m).
4
5
Use the Left and Right [ ]/[
buttons to adjust the speaker
]
• The speaker distance cannot be adjusted while a pair
of headphones is connected or the multichannel DVD
input is being used.
level, and use the Down [ ] but-
ton to select the next speaker.
The levels can be adjusted from –12 to
+12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
Speaker Levels
These settings are set automatically by the Automatic
Speaker Setup function (see page 42).
You can set the volume level of each speaker so that all
speakers can be heard equally at the listening position.
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
Repeat step 5 so that the level of
the test tone coming from each
speaker is the same.
1
6
Speakers that you set to No or None in
the Speaker Configuration (page 74) do
not output the test tone.
Press the [SETUP] button.
Setup closes.
Don’t forget to turn down the volume if
you turned it up while setting the levels.
7
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press the
[ENTER] button.
]
2
Note:
• The speaker levels cannot be adjusted while a pair of
headphones is connected or the AV receiver is muted.
• While speaker set B is on, you can adjust the volume
of the left and right speakers, from –12 dB to +12 dB.
• While speaker set B is on, you cannot adjust the levels
of speaker set A’s surround back speakers.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Equalizer Settings
Press the Down [ ] button, and
then use the Left and Right
5
These settings are set automatically by the Automatic
Speaker Setup function (see page 42).
[
]/[ ] buttons to select a
speaker.
Here you can adjust the tone of individual speakers. To
set the volume of individual speakers, see page 77.
2–5. Equalizer Settings
Equalizer
Channel
63Hz
Manual
Front
0dB
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
250Hz
0dB
0dB
0dB
0dB
1
1000Hz
4000Hz
16000Hz
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Use the Up and Down [ ]/[
buttons to select a frequency.
Use the Left and Right [ ]/[
buttons to adjust the level at that
frequency.
The volume at each frequency can be
adjusted from –6 to +6 dB in 1 dB
steps.
]
6
7
]
Use the Up and Down [ ]/[
buttons to select “2. Speaker
Setup,” and then press the
[ENTER] button.
]
2
3
4
Tip: Low frequencies (e.g., 63Hz)
affect bass sounds; high frequencies
(e.g., 16000Hz) affect treble sounds.
Use the Up [ ] button to select
“Channel,” and then use the Left
and Right [ ]/[ ] buttons to
select another speaker.
Repeat steps 5 and 6 for each speaker.
Speakers that you’ve set to No or None
in the Speaker Configuration (page 74)
cannot be selected.
Use the Up and Down [ ]/[
]
buttons to select “4. Equalizer
Settings,” and then press
[ENTER].
Use the Left and Right [ ]/[
buttons to select:
]
Press the [SETUP] button.
The setup menu closes.
8
Off: Tone off, response flat.
Audyssey: The tone for each speaker
is set automatically by the
Automatic Speaker Setup
function. Be sure to select
this setting after having
Notes:
• The front, center, surround, and surround back speak-
ers can be adjusted at 80Hz, 250Hz, 800Hz, 2500Hz,
and 8000Hz. The subwoofer can be adjusted at 40Hz,
80Hz, and 160Hz.
performed the Automatic
Speaker Setup.
• While the Direct listening mode is selected, the equal-
izer settings have no effect.
Manual: You can adjust the equal-
izer for each speaker
manually.
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
If you selected Manual, continue with
this procedure. If you selected Off or
Audyssey, go to step 8.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Source Setup
When you’ve finished, press the
[SETUP] button.
Setup closes.
6
This section explains items on the Source Setup menu.
Items can be set individually for each input selector.
Press the input selector buttons
1
to select an input source, and
then press the [RECEIVER]
REMOTE MODE button.
IntelliVolume
With IntelliVolume, you can set the input level for each
input selector individually. This is useful if one of your
source components is louder or quieter than the others.
Use the Left and Right [ ]/[ ] buttons to set the level.
If a component is noticeably louder than the others, use
the Left [ ] button to reduce its input level. If it’s
noticeably quieter, use the Right [ ] button to increase
its input level. The input level can be adjusted from
–12 dB to +12 dB in 1 dB steps.
Press the [SETUP] button.
2
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
A/V Sync
When using your DVD player’s progressive scanning
function, you may find that the picture and sound are out
of sync. With the A/V Sync setting, you can correct this
by applying a delay to the audio signal. The delay can be
set from 0 to 100 milliseconds (msec) in 10 millisecond
steps.
Use the Up and Down [ ]/[
buttons to select “4. Source
Setup,” and then press [ENTER].
]
3
4
5
Use the Left and Right [ ]/[ ] buttons to set the delay.
To view the TV picture while setting the delay, press
[ENTER].
If HDMI Lip Sync is enabled (see page 82), and your TV
or display supports HDMI Lip Sync, the displayed delay
time will be the A/V Sync delay time. The HDMI Lip
Sync delay time is displayed underneath in parentheses.
Use the Up and Down [ ]/[
buttons to select an item, and
then press [ENTER].
]
Note:
• A/V Sync is disabled when the Direct listening mode
is used with an analog input source.
Use the Left and Right [ ]/[
buttons to change it.
]
The Source Setup menu items are
explained below.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Note:
Miscellaneous Setup
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
This section explains items on the Miscellaneous menu.
Press the [RECEIVER] REMOTE
1
MODE button, followed by the
[SETUP] button.
Volume Setup
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
■ Maximum Volume
With this setting, you can limit the maximum volume.
The Maximum Volume range is Off, 79 to 30.
■ Power On Volume
This setting determines what the volume will be each
time the AV receiver is turned on.
Use the Up and Down [ ]/[
buttons to select
“6. Miscellaneous,” and then
press [ENTER].
]
2
3
4
The range is Last, Min, 1 to 79, Max.
To use the same volume level as when the AV receiver
was last turned off, select Last.
Note:
• The Power On Volume setting cannot be set higher
than the Maximum Volume setting.
■ Headphone Level
With this setting, you can offset the headphone volume
relative to the main volume. This is useful if your head-
phones are too loud or too quiet at the volume setting you
usually use when listening through your speakers. The
headphone level can be set from –12 dB to +12 dB.
Use the Up and Down [ ]/[
buttons to select an item, and
then press [ENTER].
]
OSD Setup
■ Immediate Display
This setting determines whether operation details are
displayed onscreen immediately after an AV receiver
function is used.
On: Displayed (default).
Off: Not displayed.
Even if On is selected, operation details are not output if
the input source is connected to an HDMI IN and output
by the HDMI OUT.
Use the Up and Down [ ]/[
buttons to select an item, and
use the Left and Right [ ]/[
buttons to change it.
]
]
■ Monitor Type
With this setting, you can specify the aspect ratio of your
TV so that menus are displayed properly.
The items are explained below.
16:9: Select if your TV is 16:9 (default).
4:3: Select if your TV is 4:3.
■ Display Position
This setting determines where on the screen operation
details are displayed.
Bottom: Bottom of the screen (default).
Top: Top of the screen.
When you’ve finished, press the
[SETUP] button.
5
Setup closes.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Hardware Setup
Use the Up and Down [ ]/[
]
4
buttons to select an item, and
use the Left and Right [ ]/[
buttons to change it.
This section explains items on the Hardware menu.
]
The items are explained below.
Remote
indicator
When you’ve finished, press the
[SETUP] button.
5
RECEIVER
Setup closes.
Note:
• This procedure can also be performed on the AV
receiver by using its [SETUP], [ENTER], and arrow
buttons.
ENTER
SETUP
Remote Control
■ Remote ID
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differenti-
ate the AV receiver from the other components, you can
change its remote ID from 1, the default, to 2 or 3.
Number
buttons
Note:
• If you do change the AV receiver’s remote ID, be sure
to change the remote controller to the same ID (see
below), otherwise, you won’t be able to control it with
the remote controller.
Press the [RECEIVER] REMOTE
MODE button, followed by the
[SETUP] button.
1
Changing the Remote Controller’s ID
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
While holding down the
1
[RECEIVER] REMOTE MODE but-
ton, press and hold down the
[SETUP] button until the Remote
indicator lights up (about 3 sec-
onds).
Use the Up and Down [ ]/[
]
2
3
buttons to select “7. Hardware
Setup,” and then press [ENTER].
(3 seconds)
Use the number buttons to enter
ID 1, 2, or 3.
The Remote indicator flashes twice.
2
Use the Up and Down [ ]/[
buttons to select an item, and
then press [ENTER].
]
Analog Multich
■ Subwoofer Input Sensitivity
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player. Note that
this setting only affects signals connected to the AV
receiver’s DVD SUBWOOFER jack.
The screen for that item appears.
You can select 0dB, 5dB, 10dB, or 15dB.
If you find that your subwoofer is too loud, try the 10 dB
or 15 dB setting.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
■ Audio TV Out
HDMI
This setting determines whether audio received by an
HDMI input is output by the HDMI outputs. You may
want to change this setting to On if your TV is connected
to an HDMI output and you want to listen to audio from
an HDMI component through your TV’s speakers. Nor-
mally, it should be set to Off.
You can specify the output resolution for the HDMI out-
puts and have the AV receiver upconvert the picture res-
olution as necessary to match the resolution supported
by your TV.
See the “Video Resolution Chart” on page 98 to see how
the AV receiver handles video input at different resolu-
tions.
Off: HDMI audio is not output (default).
On: HDMI audio is output.
Notes:
Through: Select this to pass video through the AV
receiver at the same resolution and with no
conversion.
Auto: Select this to have the AV receiver automati-
cally convert video at resolutions not supported
by your TV.
480p(480p/576p):Select this for 480p or 576p output
and video conversion as necessary.
720p: Select this for 720p output and video conver-
sion as necessary.
1080i: Select this for 1080i output and video conver-
sion as necessary.
• If On is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• With some TVs and input signals, no sound may be
output even if On is selected.
• When the Audio TV Out setting is set to On, or TV
Control is set to Enable and you’re listening through
your TV’s speakers (see page 36), if you turn up the
AV receiver’s volume control, the sound will be output
by the AV receiver’s speakers. To stop the AV
receiver’s speakers producing sound, change the set-
tings, change your TV’s settings, or turn down the AV
receiver’s volume.
■ Zoom Mode
This setting determines the aspect ratio that will be used
for 480i, 480p, 576i, and 576p input signals when they
are output by the HDMI OUT. This setting only applies
when the HDMI Output Resolution setting is set to 1080i
or 720p.
■ Lip Sync
The Lip Sync function can automatically synchronize
HDMI audio and video that’s gotten out of sync due to
the complex digital video processing being performed by
your HDMI-compatible TV. With HDMI Lip Sync, the
audio delay required to synchronize the audio and video
is calculated and applied automatically by the AV
receiver.
Normal:
Disable: HDMI lip sync disabled.
Enable: HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the A/V Sync screen
(see page 79).
Full:
■ x.v.Color
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color,” you can enable “x.v.Color” on
the AV receiver with this setting.
Disable: “x.v.Color” disabled.
Enable: “x.v.Color” enabled.
■ Control
This function allows RIHD-compatible components
connected via HDMI to be controlled with the AV
receiver.
Disable: RIHD disabled.
Enable: RIHD enabled.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup—Continued
Notes:
receiver’s speakers producing sound, change the set-
tings, change your TV’s settings, or turn down the AV
receiver’s volume.
• RIHD, which stands for Remote Interactive over
HDMI, is the name of the system control function
found on Onkyo components. The AV receiver can be
used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than RIHD-compatible components
and recommended components cannot be guaranteed.
Note:
• After changing the Control, Power Control, or TV
Control setting, be sure to turn all of your compo-
nents off and then back on again. Refer to the
instruction manuals for your other components.
• Select Disable if a connected component is incompat-
ible or you’re not sure about its compatibility.
• If operation is unreliable when set to Enable, select
Disable instead.
Lock Setup
With this setting, you can protect your settings by lock-
ing the setup menus.
Power Control
To link the power functions of RIHD-compatible com-
ponents connected via HDMI, select Enable.
Press the [RECEIVER] button,
1
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
Disable: Power Control disabled.
Enable: Power Control enabled.
Notes:
• The Power Control setting can be set only when the
above Control setting is set to Enable.
• HDMI power control only works with RIHD-compat-
ible components that support it and may not work
properly with some components due to their settings
or compatibility.
Use the Up and Down [ ]/[
buttons to select“8. Lock Setup,”
and then press [ENTER].
]
2
• When set to Enable, the AV receiver consumes more
power.
• When set to Enable, the AV receiver enters Ready
mode when set to Standby, and the STANDBY indica-
tor lights up.
• When set to Enable, regardless of whether the AV
receiver is On or on Standby, both audio and video
received by an HDMI input will be output by the
HDMI OUT for playback on the TV or other compo-
nent that’s connected to the HDMI OUT.
Use the Left and Right [ ]/[
buttons to select:
Locked: Setup menus locked.
Unlocked: Setup menus unlocked.
When Locked is selected, only this
Lock Setup item can be accessed.
]
3
4
TV Control
Select Enable to control the AV receiver from an RIHD-
compatible TV connected via HDMI.
Disable: TV Control disabled.
Enable: TV Control enabled.
Press the [SETUP] button.
Setup closes.
Notes:
• Select Disable if your TV is incompatible or you’re
not sure about its compatibility.
Control and Power Control settings are both set to
Enable.
• When the Audio TV Out setting is set to On, or TV
Control is set to Enable and you’re listening through
your TV’s speakers (see page 36), if you turn up the
AV receiver’s volume control, the sound will be output
by the AV receiver’s speakers. To stop the AV
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components
You can control your DVD player, CD player, and other
components with the AV receiver’s remote controller.
To control another component, you must first enter that
component’s remote control code to a REMOTE MODE
button.
Look up the component’s remote
control code in the separate
Remote Control Codes list.
1
The codes are organized by category.
This section explains how to enter remote control codes
and how to control your other components.
While holding down the REMOTE
MODE button to which you want
to enter a code, press and hold
down the [DISPLAY] button until
the Remote indicator lights up
(about 3 seconds).
2
Preprogrammed Remote Control
Codes
The following REMOTE MODE buttons are prepro-
grammed with remote control codes for controlling the
control code to control these components.
For details on controlling these components, see the
pages indicated.
Note:
• Remote control codes cannot be
entered for the [RECEIVER]
REMOTE MODE button.
• OnlyTV remote control codes can be
entered for the [TV] REMOTE
MODE button.
Onkyo DVD player (page 86)
• Apart from the [RECEIVER] and
remote control codes from any cate-
gory can be entered for the REMOTE
MODE buttons. However, these but-
tons also work as input selector but-
tons (page 50), so choose a
Onkyo CD player (page 89)
Onkyo cassette recorder with
(3 seconds)
(page 90)
Entering Remote Control Codes
REMOTE MODE button that corre-
sponds with the input to which you
connect your component. For exam-
ple, if you connect your CD player to
the CD input, choose the [CD]
You’ll need to enter a code for each component that you
want to control.
Remote
indicator
DISPLAY
REMOTE MODE button when
entering its remote control code.
REMOTE
MODE
RECEIVER
Within 30 seconds, use the num-
ber buttons to enter the 5-digit
remote control code.
3
The Remote indicator flashes twice.
If the remote control code is not entered
successfully, the Remote indicator will
flash once slowly.
Notes:
• The remote control codes provided are correct at the
time of printing but subject to change.
Number
buttons
• Only RI Docks with a remote control sensor, such as
the DS-A2 and DS-A2X, can be controlled with the
AV receiver’s remote controller and the appropriate
remote control code.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Remote Control Codes for Onkyo
Components Connected via
Resetting the REMOTE MODE Buttons
You can reset a REMOTE MODE button to its default
remote control code.
Onkyo components that are connected via
are con-
trolled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
While holding down the REMOTE
1
MODE button that you want to
reset, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
Make sure the Onkyo component is con-
1
nected with an
cable and an analog
audio cable (RCA).
See page 40 for details.
Enter the appropriate remote control code
to the REMOTE MODE button.
2
• [DVD] REMOTE MODE button
31612: Onkyo DVD player with
• [CD] REMOTE MODE button
(3 seconds)
71327: Onkyo CD player with
• [TAPE] REMOTE MODE button
Within 30 seconds, press the
2
42157: Onkyo cassette recorder with
REMOTE MODE button again.
The Remote indicator flashes twice,
indicating that the button has been
reset.
(default)
See the previous page for how to enter remote
control codes.
Each of the REMOTE MODE buttons
is preprogrammed with a remote con-
trol code. When a button is reset, its
preprogrammed code is restored.
Press the REMOTE MODE button, point
the remote controller at the AV receiver,
and operate the component.
3
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the following remote control codes:
, use
Resetting the Remote Controller
You can reset the remote controller to its default settings.
• [DVD] REMOTE MODE button
30627: Onkyo DVD player without
(default)
While holding down the
1
[RECEIVER] REMOTE MODE but-
ton, press and hold down the
[AUDIO] button until the Remote
indicator lights up (about 3 sec-
onds).
• [CD] REMOTE MODE button
71817: Onkyo CD player without
(default)
(3 seconds)
Within 30 seconds, press the
[RECEIVER] REMOTE MODE but-
ton again.
2
The Remote indicator flashes twice,
indicating that the remote controller
has been reset.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a DVD Player, or DVD Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your DVD
player (HD DVD, Blu-ray, or TV/DVD combination),
you can control your player with the following buttons.
A ON/STANDBY button
Sets the DVD player to On or Standby.
B TV [
] button
Set the TV to On or Standby.
The [DVD] REMOTE MODE button is preprogrammed
with the remote control code for controlling an Onkyo
DVD player.
C TV [INPUT] button
Selects the TV’s external inputs.
D TV VOL [ ]/[ ] button
For details on entering a remote control code for a differ-
ent component, see page 84.
Adjust the TV’s volume.
E TOP MENU button
Displays a DVD’s top menu or a DVD’s title.
F Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Press the appropriate
REMOTE MODE button first
Used to navigate menus and select items.
G SETUP button
Used to access the DVD player’s settings.
L
A
H Playback buttons
From left to right: Previous, Rewind, Pause, Play,
Stop, Fast Forward, and Next.
DVD
M
N
I REPEAT button
Used with the repeat playback function.
J SEARCH buttons
B
C
D
E
O
Used to search title, chapter, and track numbers, and
to search times for locating specific points.
K Number buttons
P
Used to enter title, chapter, and track numbers, and
to enter times for locating specific points. The [+10]
button works as a +10 button or “-.--” button.
F
G
Q
R
L DISPLAY button
Displays information about the current disc, title,
chapter, or track, including elapsed time, remaining
time, total time, and so on.
H
M MUTING button (51)
Mutes or unmutes the AV receiver.
I
J
S
T
N DISC +/–, CH +/– button
Selects discs on a DVD changer. Selects TV chan-
nels on a component with a built-in tuner.
O VOL [ ]/[ ] button (50)
K
Adjusts the volume of the AV receiver.
U
P MENU button
Displays a DVD’s menu.
Q RETURN button
Exits the DVD player’s setup menu or return to the
previous menu.
R AUDIO button
Selects foreign language soundtracks and audio for-
mats (e.g., Dolby Digital or DTS).
S RANDOM button
*
With some components, certain buttons may not
work as expected, and some may not work at all.
Used with the random playback function.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Note:
T PLAY MODE button
Selects play modes on components with selectable
play modes.
• If you enter the remote control code for a HD DVD or
Blu-ray player that has A, B, C, and D or colored but-
tons, the [SEARCH], [REPEAT], [RANDOM], and
[PLAY MODE] buttons will work as colored or A, B,
C, D buttons. In this case, these buttons cannot be used
to set repeat playback, random playback, or select play
modes.
U CLR button
Cancels functions and clears entered numbers.
Controlling a VCR, or PVR
By pressing the REMOTE MODE button that’s been
(TV/VCR, PVR, DBS/PVR combination or cable/PVR
combination), you can control your video recorder with
the following buttons.
A ON/STANDBY button
Set the video recorder to On or Standby.
B TV [
] button
Set the TV to On or Standby.
C TV [INPUT] button
For details on entering a remote control code for a differ-
ent component, see page 84.
Selects the TV’s external inputs.
D TV VOL [ ]/[ ] button
Adjust the TV’s volume.
Press the appropriate
REMOTE MODE button first
E GUIDE button
Displays the program guide or navigation list.
F Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to navigate menus and select items.
J
A
G SETUP button
Displays the video recorders setup menu.
VCR/DVR
H Previous [
] button
K
L
Previous or instant replay function.
I Number buttons
B
C
D
E
Enter numbers. The [0] button enters 11 on some
ton or “-.--” button.
M
N
J DISPLAY button
Displays information.
F
G
K MUTING button (51)
O
Mutes or unmutes the AV receiver.
L CH +/– button
P
Q
H
Selects TV channels on the video recorder.
M VOL [ ]/[ ] button (50)
Adjusts the volume of the AV receiver.
N PREV CH button
Selects the previous channel.
O RETURN button
Exits the menu or return to the previous menu.
I
P Next [
] button
Next or advance function.
R
Q Playback buttons
From left to right: Previous, Next, Rewind, Play,
Fast Forward, Pause, and Stop.
*
With some components, certain buttons may not
work as expected, and some may not work at all.
R CLR button
Cancels functions or enters the number 12.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a Satellite Receiver or Cable Receiver
By pressing the REMOTE MODE button that’s been
ellite receiver, cable receiver, or DVD recorder
(DBS/PVR combination or cable/PVR combination),
you can control your player with the following buttons.
A ON/STANDBY button
Set the component to On or Standby.
B GUIDE button
Displays the onscreen program guide.
C Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
For details on entering a remote control code for a differ-
ent component, see page 84.
Used to navigate menus and select items.
D SETUP button
Displays the setup menu.
E SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons
Press the appropriate
REMOTE MODE button first
Function as colored buttons or A, B, C, D buttons.
F Number buttons
7
A
button or “-.--” button.
CBL/SAT
G DISPLAY button
8
9
Displays information.
H MUTING button (51)
Mutes or unmutes the AV receiver.
J
I CH +/– button
Selects satellite/cable channels.
K
B
C
D
J VOL [ ]/[ ] button (50)
Adjusts the volume of the AV receiver.
K PREV CH button
L
M
Selects the previous channel.
L RETURN button
Exits the menu.
N
M AUDIO button
Selects foreign language soundtracks and audio for-
mats (e.g., Dolby Digital or DTS).
E
6
N Playback buttons
From left to right: Previous, Next, Rewind, Play,
Fast Forward, Pause, and Stop.
These buttons are for use with DBS/PVR and
cable/PVR combination-type components.
O
O CLR button
Cancels functions and clears entered numbers.
*
With some components, certain buttons may not
work as expected, and some may not work at all.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a CD Player, CD Recorder, or MD Player
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your CD
player, CD recorder, or MD player, you can control your
player with the following buttons.
A ON/STANDBY button
Set the component to On or Standby.
B TOP MENU button
Displays a menu.
The [CD] REMOTE MODE button is preprogrammed
with the remote control code for controlling an Onkyo
CD player.
C Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to navigate menus and select items.
D SETUP button
For details on entering a remote control code for a differ-
ent component, see page 84.
Used to access the Onkyo CD player’s settings.
E Playback buttons
From left to right: Previous, Rewind, Pause, Play,
Stop, Fast Forward, and Next.
Press the appropriate
REMOTE MODE button first
F REPEAT button
Used with the repeat playback function.
G SEARCH button
I
A
Used to locate specific points.
H Number buttons
CD
Used to enter track numbers and times for locating
specific points. The [+10] button works as a +10
button or “-.--” button.
J
K
I DISPLAY button
L
M
Displays information about the current disc or track,
including elapsed time, remaining time, total time,
and so on.
B
C
D
J DISC +/– button
Selects discs on a CD changer.
K RETURN button
Exits the CD player’s setup menu.
L RANDOM button
Used with the random playback function.
E
M PLAY MODE button
Selects play modes on components with selectable
play modes.
F
G
N
O
N CLR button
Cancels functions and clears entered numbers.
H
P
*
With some components, certain buttons may not
work as expected, and some may not work at all.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a Cassette Recorder
By pressing the REMOTE MODE button that’s been
programmed with the remote control code for your cas-
sette recorder, you can control your cassette recorder
with the following buttons.
On twin cassette decks, only Deck B can be controlled.
A ON/STANDBY button
Turns the cassette recorder on or off.
B Previous and Next [
The Previous [ ] button selects the previous
track. During playback it selects the beginning of
]/[
] buttons
The [TAPE] REMOTE MODE button is preprogrammed
with the remote control code for controlling an Onkyo
cassette recorder when used with an
connection.
the current track. The Next [
next track.
] button selects the
For details on entering a remote control code for a differ-
ent component, see page 84.
Depending on how they were recorded, the Previous
and Next [ ]/[ ] buttons may not work prop-
erly with some cassette tapes.
Press the appropriate
REMOTE MODE button first
C Rewind and Fast Forward [ ]/[ ] buttons
The Rewind [ ] button starts rewind. The Fast
Forward [ ] button starts fast forward.
D Reverse Play [ ] button
A
Starts reverse playback.
E Play [ ] button
TAPE
Starts playback.
F
F MUTING button (51)
Mutes or unmutes the AV receiver.
G
G VOL [ ]/[ ] button (50)
Adjusts the volume of the AV receiver.
H Stop [ ] button
Stops playback.
Note:
• An Onkyo cassette recorder connected via
also be controlled in Receiver mode.
can
2
2
3
H
3
4
5
*
With some components, certain buttons may not
work as expected, and some may not work at all.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling Other Components—Continued
Controlling a TV
been programmed with the remote control code for your
TV (TV/DVD combination or TV/VCR combination),
you can control your TV with the following buttons.
A ON/STANDBY,TV [
] buttons
Set the TV to On or Standby.
B TV VOL [ ]/[ ]*
Adjust the TV’s volume.
For details on entering a remote control code for a differ-
ent component, see page 84.
C TV [INPUT]* button
Selects the TV’s external inputs.
The [TV] REMOTE MODE button is preprogrammed
with the remote control code for controlling a TV that
supports the RIHD*. The TV must be able to receive
remote control commands via RIHD and be connected to
the AV receiver via HDMI. If controlling your TV via
RIHD doesn’t work very well, program your TV’s
remote control code into the [TV] REMOTE MODE but-
ton and use the TV remote mode to control your TV.
D GUIDE button
Displays the program guide.
E Arrow [ ]/[ ]/[ ]/[ ] and ENTER buttons
Used to navigate menus and select items.
F SETUP button
Displays a menu.
G Playback buttons
From left to right: Previous, Rewind, Pause, Play,
Stop, Fast Forward, and Next.
Press [TV] REMOTE MODE
button first
These buttons works for use with TV/DVD and
TV/VCR combination-type components.
J
A
H SEARCH, REPEAT, RANDOM, and PLAY
MODE buttons
TV
Function as colored buttons or A, B, C, D buttons.
I Number buttons
K
L
Enter numbers. [0] button enters 11 on some com-
ponents. [+10] button works as “-.--” button or +10.
A
B
C
D
J DISPLAY button
Displays information.
K MUTING button
M
Mutes the TV.
E
F
L CH +/– button
Select channels on the TV.
N
O
M PREV CH button
Selects the previous or last channel.
N RETURN button
G
H
Exits the TV’s setup menu.
O AUDIO button
Selects foreign language soundtracks and audio for-
mats (e.g., Dolby Digital or DTS).
P CLR button
9
Cancels functions and clears entered numbers, or
enters 12.
P
* The RIHD is Onkyo’s name for the CEC (Consumer
Electronics Control) system, which is part of the
HDMI specification.
*
With some components, certain buttons may not
work as expected, and some may not work at all.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact your Onkyo dealer.
• Make sure that speaker A or B is on (page 7).
• Make sure that all audio connecting plugs are pushed
in all the way (page 26).
• Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with the
metal part of each speaker terminal (page 21).
• Make sure that the speaker cables are not shorting.
designed for home theater enjoyment and has a wide
volume range for precise adjustment.
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 51).
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [ON/STANDBY] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
ON/STANDBY
• While a pair of headphones is connected to the
PHONES jack, no sound is output by the speaker set
A and B (page 52).
• Check the digital audio output settings on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
audio format from a menu or with the AUDIO button
on your DVD player’s remote controller.
you must connect one between it and the AV receiver.
nect an MC head amp, or an MC transformer and a
phono preamp.
VCR/DVR
Note that resetting the AV receiver will delete your
radio presets and custom settings.
The onscreen setup menus appear only on a TV that is
connected to the HDMI OUT. If your TV is connected
to the composite video or S-Video MONITOR OUT,
or the COMPONENT VIDEO OUT, use the HT-
R667’s own display when changing settings.
Power
• Check the speaker settings (pages 74–78).
• If the digital signal format is set to PCM or DTS, set it
to Auto (page 53).
• If there’s no sound from a DVD player connected to an
HDMI IN, check the DVD player’s output settings,
and be sure to select a compatible audio format.
Can’t turn on the AV receiver
• Make sure that the power cord is plugged into the wall
outlet properly.
• Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it back in again.
The AV receiver turns off as soon as it’s turned
on
Only the front speakers produce sound
• When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
• Check the Speaker Configuration (page 74).
• The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord discon-
nected for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact your Onkyo dealer.
Only the center speaker produces sound
Pro Logic IIx Music listening mode with a mono
source, such as an AM radio station or mono TV pro-
speaker.
• Check the Speaker Configuration (page 74).
The center speaker produces no sound
• When the Stereo or Mono listening mode is selected,
the center speaker produces no sound (page 66).
• Check the Speaker Configuration (page 74).
Audio
There’s no sound or it’s very quiet
• To listen to an audio source that’s connected to an
HDMI input, make sure that input is assigned to an
through the AV receiver and can only be heard from
your TV.
• To listen to an audio source that’s connected to an
OPTICAL or COAXIAL input, make sure that input is
assigned to an input selector (page 47).
The surround speakers produce no sound
the surround speakers produce no sound.
• Depending on the source and the current listening
mode, not much sound may be produced by the sur-
round speakers. Try another listening mode (page 59).
• Check the Speaker Configuration (page 74).
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
The surround back speakers produce no sound
• The surround back speakers are not used with all lis-
tening modes. Try another listening mode (page 59).
back speakers with some sources.
About DTS signals
• When playing DTS program material, using the pause,
fast forward, or fast reverse function on your player
may produce a short audible noise. This is not a mal-
function.
• Check the Speaker Configuration (page 74).
• While speaker set B is on, speaker set A is reduced to
5.1-channels and the surround back speakers produce
no sound (page 7).
• When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, as the AV receiver does not
switch formats immediately, you may not hear any-
thing, in which case you should stop your player for
about 3 seconds, and then resume playback.
• With some CD players, you won’t be able to playback
DTS material properly even though your player is con-
nected to a digital input on the AV receiver. This is
usually because the DTS bitstream has been processed
(e.g., output level, sampling rate, or frequency
response changed) and the AV receiver doesn’t recog-
nize it as a genuine DTS signal. In such cases, you
may hear noise.
The subwoofer produces no sound
• The subwoofer outputs no sound while only speaker
set B is on. Turn on speaker set A.
• If the source material contains no audio in the LFE
channel, the subwoofer produces no sound.
• Check the Speaker Configuration (page 74).
Speaker set B produces no sound
• Speaker set B only outputs sources that are connected
to an analog input. Check to see if the source compo-
nent is connected to an analog input.
There’s no sound with a certain signal format
• Check the digital audio output setting on the source
component. On some game consoles, such as those
that can play DVDs, the default setting is off.
• With some DVD-Video discs, you need to select an
on your DVD player’s remote controller.
The beginning of audio received by an HDMI IN
can’t be heard
• Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, sound may not be output immediately.
Can’t get 6.1- or 7.1-channel playback
• While speaker set B is on, playback in the main room
speakers produce no sound (page 7).
Video
There’s no picture
• Make sure that all video connecting plugs are pushed
in all the way (page 26).
• Make sure that each video component is properly con-
nected.
the AV receiver is connected is selected.
• The AV receiver does not convert between formats, so
nent video input, your TV must be connected to the
component video output (page 28).
The volume cannot be set to 79
run, or the volume level of each individual speaker has
been adjusted (pages 42 and 77), the maximum vol-
ume may be reduced.
• When the levels of each speaker have been adjusted
(page 77), the maximum possible volume may be
reduced.
Noise can be heard
cords, speaker cables, and so on can degrade audio
performance, so don’t use them.
• If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 28).
• An audio cable may be picking up interference. Try
repositioning your cables.
• When the Equalizer setting (page 78) is set to Audys-
sey, the maximum possible volume is reduced by
6 dB.
There’s no picture from a source connected to
• Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 36).
• If the message “Resolution Error” appears on the AV
receiver’s display, this indicates that your TV does not
support the current video resolution and you need to
select another resolution on your DVD player.
• Make sure that the source is Dolby Digital (page 71).
The DVD multichannel input doesn’t work
• Check the multichannel input connections (page 31).
• Make sure that the multichannel input is selected
(page 50).
• Check the audio output settings on your DVD player.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
with the same name (e.g., TAPE IN to TAPE OUT or
VCR/DVR IN to VCR/DVR OUT).
Tuner
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
light up
Others
The sound changes when I connect my head-
phones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, or Direct, in which case it stays the same.
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• When listening to anAM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
How do I change the language of a multiplex
source
• On the “Audio Adjust” menu, change the “Multiplex
The
• To use
functions don’t work
Remote Controller
, you must make an
connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 40).
The remote controller doesn’t work
rect polarity (page 17).
• Make sure that the remote controller is not too far
away from the AV receiver and there’s no obstruction
remote control sensor (page 17).
• Make sure you’ve selected the correct remote control-
ler mode.
The following settings can be made for the
S-Video and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
• Make sure you’ve entered the correct remote control
code (page 84).
Can’t control other components
• Make sure you’ve selected the correct remote control-
ler mode.
2. Use the Left and Right [ ]/[ ] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
• If you’ve connected an
-capable Onkyo MD
recorder or CD recorder to the TAPE IN/OUT jacks,
or to the CBL/SAT IN jacks, for the remote controller
to work properly, you must set the Input Display to
MD or CDR, respectively (see page 48).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
work as expected, and some may not work at all.
• To control an Onkyo component that’s connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 85).
• Video Attenuation
This setting can be made for the DVD, VCR/DVR,
CBL/SAT, or AUX input.
If you have a games console connected to the
S-Video or composite video input, and the picture
isn’t very clear, you can attenuate the gain.
Video ATT:0: (default).
Video ATT:2: Gain is reduced by 2 dB.
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup.In the unlikely event
that this happens, unplug the power cord from the wall out-
let, wait at least 5 seconds, and then plug it back in again.
• To control an Onkyo component that’s not connected
via
, or another manufacturer’s component, point
the remote controller at that component. Be sure to
enter the appropriate remote control code first
(page 84).
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
this unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
Recording
Can’t record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
Before disconnecting the power cord from the wall out-
let, set the AV receiver to Standby.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
Important Note Regarding Video Playback
The AV receiver can upscale component video, S-Video, and composite video sources for display on a TV
connected to the HDMI OUT. However, if the picture quality of the source is poor, upscaling may make the
picture worse or disappear altogether.
In this case, try setting the HDMI Output Resolution setting (page 82) to 480p or 720p. If that doesn’t
improve the picture quality, try the following:
1. If the video source is connected to a component video input,
connect your TV to the COMPONENT VIDEO OUT.
If the video source is connected to an S-Video input,
connect your TV to an S-Video output.
If the video source is connected to a composite video input,
connect your TV to a composite video output.
2. On the main menu, select “1. Input Assign,”
and then select “1. HDMI Input.”
Select the relevant input selector, and assign it to “-----” (page 46).
3. On the main menu, select “1. Input Assign,”
and then select “2. Component Video Input” (page 47):
If the video source is connected to COMPONENT VIDEO IN 1,
select the relevant input selector, and assign it to “IN1.”
If the video source is connected to COMPONENT VIDEO IN 2,
select the relevant input selector, and assign it to “IN2.”
If the video source is connected to an S-Video input or composite video input,
select the relevant input selector, and assign it to “-----”.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
HT-R667
Amplifier Section
General
Rated Output Power
North American:
Power Supply
Power Consumption
AC 120 V, 60Hz
4.2 A
130 watts minimum continuous power per channel, 8 ohm
loads, 1 channel driven at 1 kHz, with a maximum total
harmonic distortion of 1% (FTC)
Dimensions
(W × H × D)
17-1/8"
22.1 lbs.
×
5-7/8"× 14-15/16"
Weight
Dynamic Power
210 W (3Ω, Front)
190 W (4Ω, Front)
130 W (8Ω, Front)
■ Video Inputs
HDMI (Assignable)
Component
S-Video
Composite
IN 1, IN 2, IN 3, IN 4
IN 1, IN 2
DVD, VCR/DVR, CBL/SAT
DVD, VCR/DVR, CBL/SAT, AUX
THD (Total Harmonic
Distortion)
0.08% (1kHz 1W) (Power Rated)
Damping Factor
60 (Front, 1kHz, 8Ω)
Input Sensitivity and
Impedance
200 mV/ 47 kΩ (LINE)
■ Video Outputs
HDMI
Component
S-Video
Output Level and
Impedance
Frequency Response
Tone Control
OUT
OUT
200 mV/ 2.2 kΩ (REC OUT)
5Hz–100kHz/ +1 dB–3 dB (Direct mode)
10 dB, 50Hz (BASS)
MONITOR OUT, VCR/DVR (REC OUT)
MONITOR OUT, VCR/DVR (REC OUT)
Composite
10 dB, 20kHz (TREBLE)
100 dB (LINE, IHF-A)
8Ω–16Ω
Signal to Noise Ratio
Speaker Impedance
■ Audio Inputs
Digital Inputs
(Assignable)
2 (Rear OPT), 2 (Rear COAXIAL)
DVD (MULTI CHANNEL), VCR/DVR,
CBL/SAT, AUX, TAPE, CD, DOCK
Video Section
Analog Inputs
Input Sensitivity/Output
Level and Impedance
Multichannel Inputs
7.1 ch
1 Vp-p /75Ω (Component and S-VideoY)
0.7 Vp-p /75Ω (Component Pb/Cb, Pr/Cr)
0.28 Vp-p /75Ω (S-Video C)
■ Audio Outputs
Analog Outputs
Subwoofer Pre Outputs
Speaker Outputs
TAPE, VCR/DVR
1
SP-A (L, R, C, SL, SR, SBL, SBR) +
SP-B (L, R)
1 Vp-p /75Ω (Composite)
Component Video
Frequency Response
5Hz – 50MHz, –3 dB
Phones
PHONES
Tuner Section
■ Control Terminal
MIC
Yes
■ FM
Tuning Frequency Range 87.5MHz–107.9MHz
■ AM
Tuning Frequency Range 530kHz–1710kHz
Specifications and features are subject to change without
notice.
Preset Channel
40
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications—Continued
Speaker Package HTP-750X
Dock DS-A1L
■ Powered Subwoofer (SKW-750X)
Power supply:
Consumption:
Dimensions
(W × H × D):
Weight:
DC 5 V 500 mA
2.5 W Max.
Type:
Bass-reflex
Input sensitivity/
Impedance:
Maximum output power:290 W
140 mV/20 kΩ
4-7/16" × 2-3/8" × 4-7/16"
0.7 lbs.
Frequency response:
Cabinet capacity:
Dimensions
25 Hz–150 Hz
1.3 cubic feet
(W × H × D):
10-13/16" × 19-15/16" × 16-3/16"
(incl. grille and projection)
25.6 lbs.
10" Cone Woofer
AC 120 V/ 60 Hz
163 W
Specifications and features are subject to change without
notice.
Weight:
Drivers unit:
Power supply:
Power consumption:
Other:
Auto standby
■ Front/Center Speaker
(SKF-750XF/SKC-750XC)
Type:
2 Way Closed Type
Impedance:
Maximum input power: 110 W
Output sound pressure
8 Ω
level
:
79 dB/W/m
60 Hz–50 kHz
3 kHz
Frequency response:
Crossover frequency:
Cabinet capacity:
Dimensions
0.07 cubic feet
(W × H × D):
5-1/2" × 14" × 3-11/16"
(incl. grille and projection)
4.0 lbs.
Weight:
Drivers unit:
3-1/8" Cone Woofer × 2
1 inch Balanced Dome Tweeter × 1
Spring Type Color Coded
2
4 inch screw
Fixed
Terminal:
Keyhole slot:
Thread insert:
Grille:
Other:
Magnetic shielding
■ Surround/Surround Back Speaker
(SKM-750XS/SKB-750X)
Type:
2 Way Closed Type
Impedance:
Maximum input power: 110 W
Output sound pressure
8 Ω
level
:
76 dB/W/m
Frequency response:
Cabinet capacity:
Dimensions
(W × H × D):
60 Hz–50 kHz
0.07 cubic feet
5-1/2" × 14" × 3-11/16"
(incl. grille and projection)
2.9 lbs.
Weight:
Drivers unit:
3-1/8" Cone Woofer × 1
1 inchBalanced Dome Tweeter × 1
Spring Type Color Coded
2
4 inch screw
Fixed
Terminal:
Keyhole slot:
Thread insert:
Grille:
Other:
Magnetic shielding
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Resolution Chart
The following tables show how video signals at different resolutions are output by the AV receiver.
NTSC
COMPOSITE
S-VIDEO
Output
HDMI
COMPONENT
NTSC PAL NTSC PAL
Input
1080P 1080i 720P 480P 480i 1080P 1080i 720P 480P 480i 480i
576i
480i
576i
1080P
1080i
720P
480P
480i
✔
✔
✔
✔
✔
HDMI
1080P
1080i
720P
480P
480i
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
COMPONENT
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
480i
S-VIDEO
✔
COMPOSITE
480i
✔
PAL
COMPOSITE
S-VIDEO
Output
HDMI
COMPONENT
NTSC PAL NTSC PAL
Input
1080P 1080i 720P 576P 576i 1080P 1080i 720P 576P 576i 480i
576i
480i
576i
1080P
1080i
720P
576P
576i
✔
✔
✔
✔
✔
HDMI
1080P
1080i
720P
576P
576i
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
COMPONENT
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
576i
S-VIDEO
✔
COMPOSITE
576i
✔
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Onscreen Setup Menu Map
The onscreen setup menus appear on the connected TV and provide a conve-
nient way to change the AV receiver’s various settings. Settings are organized
into eight categories on the main menu, most containing a submenu.
Menu
1. Input Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
The onscreen setup menus appear only on a TV that is connected to the
HDMI OUT. If your TV is connected to the composite video or S-Video
MONITOR OUT, or the COMPONENT VIDEO OUT, use the HT-R667’s
own display when changing settings.
Menu Map
The following map shows how the setup menus are organized. Use the page numbers to locate information about items.
Main menu
Submenu
☞ pages 46–48
Menu
1. Input Assign
2. Speaker Setup
3. Audio Adjust
1. Input Assign
1. HDMI Input
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Lock Setup
2. Component Video Input
3. Digital Audio Input
☞ pages 74–78
2. Speaker Setup
1. Speaker Configuration
3. Level Calibration
4. Equalizer Settings
☞ page 80
6. Miscellaneous
1. Volume Setup
2. OSD Setup
page 74
☞ page 69
3. Audio Adjust
1. Multiplex/Mono
2. PL x/Neo:6
3. Dolby EX
☞ page 81
4. Theater-Dimensional
7. Hardware Setup
1. Remote Control
2. Analog Multich
3. HDMI
☞ pages 79
4. Source Setup
DVD
1. IntelliVolume
2. A/V Sync
☞ page 83
8. Lock Setup
Lock
Unlocked
☞ page 73
5. Listening Mode Preset
1. DVD
2. VCR/DVR
3. CBL/SAT
4. AUX
5. TAPE
6. TUNER
7. CD
8. DOCK
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
http://www.onkyo.com/
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
I0808-3
SN 29344677B
(C) Copyright 2008 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 6 7 7 B *
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Multiquip Landscape Lighting BGMP User Manual
NetComm Network Card NP745n User Manual
NETGEAR Switch GS724T User Manual
Nikon Scanner LS 4500AF User Manual
Nokia Bluetooth Headset BH 504 User Manual
NordicTrack Treadmill NTTL16901 User Manual
Nortel Networks Switch 8692SF User Manual
Numark Industries Turntable tt2200 User Manual
Panasonic Car Stereo System C1305L User Manual
Panasonic Stereo Amplifier cy m7052euc User Manual