Onkyo Stereo Receiver HT RC430 User Manual

Contents

AV RECEIVER

Safety Information and Introduction ............2

Table of Contents...........................................5

Connections .................................................11

Turning On & Basic Operations..................19

Advanced Operations ..................................35

Controlling Other Components...................46

Appendix.......................................................52

HT-RC430

Instruction Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

5. Preventing Hearing Loss

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Precautions

Caution

Excessive sound pressure from earphones and

headphones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal without

the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact your

Onkyo dealer.

Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat as sunshine, fire or the

like.

3. Care—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners,

alcohol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

7. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands are

wet or damp. If water or any other liquid gets inside

this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally

bought it.

• Do not leave rubber or plastic items on this unit for a

long time, because they may leave marks on the

case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be sure

to use it occasionally.

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country. Make

sure that the voltage in your area meets the voltage

requirements printed on the unit’s rear panel (e.g., AC

230 V, 50 Hz or AC 120 V, 60 Hz).

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug is

readily operable (easily accessible) at all times.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CONFORME À LA NORME NMB-003

DU CANADA.

For models with [POWER] button, or with both

[POWER] and [ON/STANDBY] buttons:

Pressing the [POWER] button to select OFF mode

does not fully disconnect from the mains. If you do not

intend to use the unit for an extended period, remove

the power cord from the AC outlet.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

NOTE:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

For models with [ON/STANDBY] button only:

Pressing the [ON/STANDBY] button to select

Standby mode does not fully disconnect from the

mains. If you do not intend to use the unit for an

extended period, remove the power cord from the AC

outlet.

En-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

■ Aiming the remote controller

To use the remote controller, point it at the AV receiver’s

remote control sensor, as shown below.

■ Installing the batteries

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ page 18)

AM loop antenna (➔ page 18)

Remote control sensor

AV receiver

Speaker cable labels (➔ page 12)

Remote controller (RC-799M) and two batteries (AA/R6)

Quick Start Guide

In catalogs and on packaging, the letter at the end of the product

name indicates the color. Specifications and operations are the

same regardless of color.

Approx. 16 ft. (5 m)

Batteries (AA/R6)

Note

• If the remote controller doesn’t work reliably, try replacing the

batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time,

remove the batteries to prevent damage from leakage or

corrosion.

• Remove expired batteries as soon as possible to prevent damage

from leakage or corrosion.

Thank you for purchasing an Onkyo AV Receiver.

Please read this manual thoroughly before making

connections and plugging in the unit.

Following the instructions in this manual will

enable you to obtain optimum performance and

listening enjoyment from your new AV Receiver.

Please retain this manual for future reference.

En-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

Using Basic Functions...............................................26

Using the Listening Modes .......................................26

Using the Home Menu..............................................31

Selecting Speakers A and B.....................................31

Using the Sleep Timer ..............................................32

Setting the Display Brightness..................................32

Displaying Source Information..................................32

Changing the Input Display.......................................33

Using the Music Optimizer........................................33

Muting the AV Receiver............................................33

Using Headphones ...................................................34

Recording .................................................................34

Table of Contents

Appendix

Troubleshooting......................................................... 52

Connection Tips and Video Signal Path .................. 57

Using an RIHD-compatible TV, Player,

or Recorder .............................................................. 58

About HDMI................................................................. 60

USB Features.............................................................. 61

License and Trademark Information ........................ 62

Specifications............................................................. 63

Safety Information and Introduction

Important Safety Instructions......................................2

Precautions ...................................................................3

Supplied Accessories...................................................4

Table of Contents..........................................................5

Features.........................................................................6

Front & Rear Panels......................................................7

Front Panel..................................................................7

Display ........................................................................8

Rear Panel ..................................................................9

Remote Controller.......................................................10

Controlling the AV Receiver......................................10

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

8ON/STANDBY (➔ page 52).

Adva nce d Ope r at ions

On-screen Setup.........................................................35

Common Procedures in Setup Menu........................35

Setup menu items.....................................................36

HDMI Input................................................................37

Component (Component Video Input)......................37

Digital Audio (Digital Audio Input).............................38

Sp Config (Speaker Configuration)...........................38

Sp Distance (Speaker Distance)...............................39

Level Cal (Level Calibration).....................................39

Audio Adjust..............................................................40

Source Setup............................................................41

Hardware ..................................................................42

HDMI Setup ..............................................................43

Using the Audio Settings ..........................................44

Connections

Connecting the AV Receiver......................................11

Connecting Your Speakers .......................................11

About AV Connections..............................................14

Connecting Components with HDMI.........................15

Connecting Your Components..................................16

Connecting Onkyo uComponents.........................17

Connecting a Recording Component........................17

Connecting the Antennas..........................................18

Connecting the Power Cord......................................18

Controlling Other Components

Turning On & Basic Operations

iPod/iPhone Playback via Onkyo Dock ....................46

Using the Onkyo Dock..............................................46

Controlling Your iPod/iPhone....................................47

Controlling Other Onkyo Components.....................48

Preprogrammed Remote Control Codes ..................48

Entering Remote Control Codes...............................48

Remote Co ntrol Codes for

Onkyo Components Connected via u.................48

Resetting the REMOTE MODE Buttons ...................49

Resetting the Remote Controller ..............................49

Controlling Other Components .................................50

Turning On/Off the AV Receiver................................19

Turning On ................................................................19

Turning Off ................................................................19

Playback ......................................................................20

Playing the Connected Component ..........................20

Controlling Contents of USB Devices .......................21

Understand ing Icons on the D i splay .........................22

Playing an iPod/iPhone via USB...............................22

Playing a USB Device...............................................23

Listening to AM/FM Radio.........................................24

En-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

Connections

Features

• 4 HDMI Inputs and 1 Output

Amplifier

• Onkyo pfor System Control

• 3 Digital Inputs (2 Optical/1 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Front-Panel USB Input for Memory Devices and

• 60 Watts/Channel @ 8 ohms (FTC)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

iPod /iPhone models

Miscellaneous

Processing

• 40 FM/AM Presets

• Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 400 ms)

• Auto Standby Function

• HDMI (Audio Return Channel, 3D, DeepColor,

x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD

High Resolution Audio, Dolby TrueHD, Dolby Digital

Plus, DSD and Multi-CH PCM)

• Non-Scaling Configuration

• On-Screen Display via HDMI

• A-Form Listening Mode Memory

• Direct Mode

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

En-6

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

Front & Rear Panels

Front Panel

b cd e f

g h i j k l m

o p

s t

For detailed information, see the pages in parentheses.

a 8ON/STANDBY button (19)

b HDMI THRU indicator (43)

c SPEAKERS A and B buttons (31)

d Remote control sensor (4)

e LISTENING MODE buttons (26)

f Display (8)

k SETUP button (35)

l TUNING q/w, PRESET e/r(24), cursor and

ENTER buttons

m RETURN button

n MASTER VOLUM E control (20)

o MUSIC OPTIMIZER button (33, 45)

p PHONES jack (34)

q TONE and Tone Level buttons (44)

r Input selector buttons (20)

s AUX INPUT AUDIO and VIDEO jacks (16)

t USB port (16)

g DIMMER button (32)

h MEMORY button (25)

i TUNING MODE button (24)

j DISPLAY button (32)

En-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

Display

a b

ꢀ

For detailed information, see the pages in parentheses.

a A and B speaker indicators (31)

b M.Opt indicator (33, 45)

c Listening mode and format indicators (26, 42)

d Tuning indicators

AUTO indicator (24)

TUNED indicator (24)

FM STEREO indicator (24)

e SLEEP indicator (32)

f HDMI indicator (43, 57)

g MUTING indicator (33)

h Message area

En-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

Rear Panel

a b c

d e

a DIGITAL IN COAXIAL and OPTICAL jacks

b COMPONENT VIDEO IN and OUT jacks

c HDMI IN and OUT jacks

i Composite video and analog audio jacks

(BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN,

GAME IN, TV/CD IN)

j MONITOR OUT V jack

d FM ANTENNA jack and AM ANTENNA terminal

e SUBWOOFER PRE OUT jack

f SPEAKERS terminals

See “Connecting the AV Receiver” for connection

(➔ pages 11 to 18).

(FRONT A, CENTER, SURROUND, FRONT B)

g Power cord

h u REMOTE CONTROL jack

En-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Information and Introduction

■ Controlling the tuner

To control the AV receiver’s tuner, press AM or FM (or

RECEIVER).

To control the AV receiver, press RECEIVERto select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player, and

other components.

Remote Controller

Controlling the AV Receiver

a q/wbuttons (24)

b D.TUN button (24)

c DISPLAY button

d CH +/– button (25)

e Number buttons (24)

See “Entering Remote Control Codes” for more

details (➔ page 48).

For detailed information, see the pages in parentheses.

a 8button (19)

b REMOTE MODE/INPUT SELECTOR buttons (20)

c TONE and Tone Level buttons (44)

d SP A/B bu tton (31)

e q/w/e/rand ENTER buttons

f SETUP button (35)

g Listening Mode buttons (26)

h DIMMER button (32)

i DISPLAY button (32)

j MUTING button (33)

k VOL q/wbutton (20)

l RETURN button

m HOME button (31)

n SLEEP button (32)

En-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Connecting the AV

Receiver

Surround

right

Surround

left

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows how to connect the

speakers to each pair of terminals.

■ Push-type speaker terminals

Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends

of the speaker cables, and twist the bare wires tightly, as

shown.

3/8" to 1/2" (10 to 12 mm)

Front B right

Front B left

Front A right

Center

Front A left

Speakers B

Speakers A

En-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

Speaker Configuration

Attaching the Speaker Cable Labels

The following table indicates the channels you should use

depending on the number of speakers that you have.

No matter how many speakers you use, a powered

subwoofer is recommended for a really powerful and solid

bass.

The speaker terminals are color-coded for identification

purpose.

Speaker

Color

White

Red

Front left

Front right

Center

To get the best from your surround sound system, you need

to set the speaker settings manually (➔ page 38).

Green

Blue

Surround left

Surround right

Number of speakers

Front speakers

Gray

✔

The supplied speaker cable labels are also color-coded and

you should attach them to the positive (+) side of each

speaker cable in accordance with the table above. Then all

you need to do is to match the color of each label to the

corresponding speaker terminal.

Center speaker

Surround speakers

✔

En-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

• Don’t connect more than one cable to each speaker

terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Speaker Connection Precautions

Using a Powered Subwoofer

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower

impedance, and use the amplifier at high volume levels

for a long period of time, the built-in amp protection

circuit may be activated.

LINE INPUT

• Disconnect the power cord from the wall outlet before

making any connections.

Powered subwoofer

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive (+)

terminals, and negative (–) terminals only to negative (–)

terminals. If you get them the wrong way around, the

sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

Corner

position

1/3 of wall

position

• Make sure the metal core of the wire does not have

contact with the AV receiver’s rear panel. Doing so may

damage the AV receiver.

To find the best position for your subwoofer, while playing

a movie or some music with good bass, experiment by

placing your subwoofer at various positions within the

room, and choose the one that provides the most satisfying

results.

Tip

• If your subwoofer is unpowered and you’re using an external

amplifier, connect the subwoofer pre out jack to an input on the

amplifier.

En-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections

■ Optical digital audio

Optical digital connections allow you to enjoy digital

AV Cables and Jacks

About AV Connections

sound such as PCM , Dolby Digital or DTS. The audio

■ HDMI

Connecting AV components

quality is the same as coaxial.

HDMI connections can carry digital video and audio.

HDMI cable

: Video & Audio

TV, projector, etc.

■ Component video

■ Coaxial digital audio

Coaxial digital connections allow you to enjoy digital

AV receiver

Component video separates the luminance (Y) and color

difference signals (PB, PR), providing the best picture

quality (some TV manufacturers label their component

video sockets slightly differently).

sound such as PCM , Dolby Digital or DTS. The audio

quality is the same as optical.

Orange

Green

Blue

Red

Blu-ray Disc/

DVD player

P^B

■ Analog audio (RCA)

Game console

Analog audio connections (RCA) carry analog audio.

Other cables

: Video

: Audio

White

Red

■ Composite video

Composite video is commonly used on TVs, VCRs, and

See also:

• “Playing an iPod/iPhone via USB” (➔ page 22)

• “Playing a USB Device” (➔ page 23)

• “Listening to AM/FM Radio” (➔ page 24)

• “iPod/iPhone Playback via Onkyo Dock”

(➔ page 46)

• “Controlling Other Onkyo Components”

(➔ page 48)

To adjust the volume, use VOL q/w.

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (➔ page 26)

En-20

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

TOP MENU

RANDOM

This button performs random playback.

Controlling Contents of USB Devices

This button displays the top menu for each media or service.

REPEAT

q/wand ENTER

Press this button repeatedly to cycle through the repeat

modes.

These buttons navigate through the menus.

e/r

This button cycles through pages.

Tip

PLAYLIST e/r

• See “Controlling Other Onkyo Components” about the operation

of other components (➔ page 48).

In Standard Mode (iPod/iPhone), this button selects

playlists.

PressUSB

first.

Note

• The buttons you can use will differ depending on the devices and

media used for playback.

This button starts playback.

This button selects the beginning of the current song.

Pressing this button twice selects the previous song.

This button fast-reverses the current song.

This button pauses playback.

You can toggle between the playback screen and the list

screen during playback.

DISPLAY

This button switches between song information.

CH +/–

In Standard Mode (iPod/iPhone), this button selects albums.

RETURN

This button returns to the previous menu.

This button selects the next song.

This button fast-forwards the current song.

This button stops playback.

MODE

You can switch between Extended Mode and Standard Mode

during iPod/iPhone playback.

En-21

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Use q/wto select a music file, and press ENTER or

Understanding Icons on the Display

Playing an iPod/iPhone via USB

1to start playback.

This section describes icons that appear on the AV

receiver’s display during media playback.

The on-screen menus appear only on a TV that is

connected to the HDMI OUT.

Note

Icon

Description

• While the message “Connecting...” appears on the AV receiver’s

display, do not disconnect the USB cable supplied with your

iPod/iPhone or the USB device from the USB port.

• If you connect an iPod or iPhone to the USB port, no sound will

be output from the headphones jack.

This section explains how to play music files on the

iPod/iPhone.

Compatible iPod/iPhone models

Folder

Track

Made for:

Playback

iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic,

iPod nano (2nd, 3rd, 4th, 5th and 6th generation),

iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Extended Mode Control

Pause

The content information is displayed (lists are displayed),

and you can control the content while looking at the screen.

Top screen list:

Playlists, Artists, Albums, Genres, Songs, Composers,

Shuffle Songs, Now Playing.

Press USB to select the “USB” input.

Fast Forward

Fast Reverse

Artist

Connect the USB cable that comes with the

iPod/iPhone to the USB port on the front of the AV

receiver.

Standard Mode Control

While reading the contents of your iPod/iPhone, the

message “Connecting...” appears on the AV

receiver’s display.

The content information is not displayed, but can be

operated using the iPod/iPhone or the remote controller.

Album

A list of your iPod/iPhone model’s contents appears

(Extended Mode).

Repeat One Track

Repeat Folder (USB Device)

Repeat

Use q/wto select a folder, and then press ENTER to

open it.

Tip

• If you want to operate using the iPod/iPhone or the remote

controller, press MODE to switch to Standard mode.

• When you disconnect the iPod/iPhone, the AV receiver

remembers the current mode. This means that if you

disconnect when in Extended Mode, the AV receiver will

start in Extended Mode the next time you connect the

iPod/iPhone.

Shuffle

Shuffle Album (iPod/iPhone)

• You can also use the q/w, ENTER and TUNING MODE

buttons on the front panel. TUNING MODE allows you to

switch modes.

• When connecting your iPod/iPhone with a USB cable, we

recommend you use an official USB cable from Apple Inc.

En-22

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Playing a USB Device

The on-screen menus appear only on a TV that is

connected to the HDMI OUT.

This section explains how to play music files from a USB

device (e.g., USB flash drives and MP3 players).

See also:

• “USB Features” (➔ page 61)

Press USB to select the “USB” input.

Plug your USB device into the AV receiver’s USB

port.

While reading the contents of your USB device, the

message “Connecting...” appears on the AV

receiver’s display.

Press ENTER.

A list of the device’s contents appears. To open a

folder, use q/wto select it, and then press ENTER.

Use q/wto select a music file, and press ENTER or

1to start playback.

Note

• While the message “Connecting...” appears on the AV receiver’s

display, do not disconnect the USB cable supplied with your

iPod/iPhone or the USB device from the USB port.

En-23

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

■ Manual tuning mode

Tuning into Radio Stations

Listening to AM/FM Radio

In manual tuning mode, FM stations will be in mono.

■ Auto tuning mode

This section describes the procedure using the buttons

on the front panel unless otherwise specified.

Press TUNING MODE so that the AUTO indicator

goes off on the AV receiver’s display.

Press TUNING MODE so that the AUTO indicator

lights on the AV receiver’s display.

Press and hold TUNING q/w.

Using the Tuner

Press TUNING q/w.

The frequency stops changing when you release the

button.

With the built-in tuner you can enjoy AM and FM radio

stations. You can store your favorite stations as presets for

quick selection.

Searching stops when a station is found.

Press the buttons repeatedly to change the frequency

one step at a time.

When tuned into a station, the TUNED indicator

lights. When tuned into a stereo FM station, the FM

STEREO indicator lights as shown.

You can also change the frequency steps (➔ page 42).

■ Tuning into stations by frequency

You can tune into AM and FM stations directly by entering

the appropriate frequency.

FM STEREO

Press AM or FM to select either “AM” or “FM”.

In this example, FM has been selected.

Band

Frequency

On the remote controller, press AM or FM to select

“AM” or “FM”, followed by D.TUN.

AUTO

TUNED

Tip

(Actual display depends on the country.)

• Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be

impossible to get good reception. In this case, switch to

manual tuning mode and listen to the station in mono.

(Actual display depends on the country.)

Within 8 seconds, use the number buttons to enter

the frequency of the radio station.

For example, to tune to 87.5 (FM), press 8, 7, 5.

If you have entered the wrong number, you can retry

after 8 seconds.

En-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

■ Selecting Presets

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite

AM/FM radio stations as presets.

To select a preset, use PRESET e/ron the AV

receiver, or the remote controller’s CH +/–.

Tip

Tune into the AM/FM station that you want to store

as a preset.

• You can also use the remote controller’s number buttons to

select a preset directly.

See the previous section.

Press MEMORY.

The preset number flashes.

■ Deleting Presets

Select the preset that you want to delete.

See the previous section.

(Actual display depends on the country.)

While holding down MEMORY, press TUNING

MODE.

The preset is deleted and its number disappears from

the AV receiver’s display.

While the preset number is flashing (about 8

seconds), use PRESET e/rto select a preset from

1 through 40.

Press MEMORY again to store the station or

channel.

The station or channel is stored and the preset number

stops flashing.

Repeat this procedure for all of your favorite AM/FM

radio stations.

En-25

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

MOVIE/TV button

This button selects the listening modes intended for use

with movies and TV.

Using Basic Functions

Using the Listening Modes

MUSIC button

This button selects the listening modes intended for use

with music.

Selecting Listening Modes

GAME button

See “About Listening Modes” for detailed information

This button selects the listening modes intended for use

with video games.

STEREO button

about the listening modes (➔ page 27).

■ Listening Mode Buttons

This button selects the Stereo listening mode and All

Channel Stereo listening mode.

Press RECEIVER first.

• The Dolby Digital and DTS listening modes can only be

selected if your Blu-ray Disc/DVD player is connected to

the AV receiver with a digital audio connection (coaxial,

optical, or HDMI).

• The listening modes you can select depends on the format

of the input signal. To check the format, see “Displaying

Source Information” (➔ page 32).

MOVIE/TV, MUSIC, GAME

• While a pair of headphones is connected, you can select the

following listening modes: Direct, Stereo, and Mono.

• While Speakers A and B are on, you can select only the

Direct, Stereo, Mono, or T-D (Theater-Dimensional)

listening mode.

MUSIC

GAME

MOVIE/TV

STEREO

En-26

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Input Source

Speaker Layout

About Listening Modes

The following audio formats are supported by the listening

mode.

The illustration shows which speakers are activated in each

channel. See “Sp Config (Speaker Configuration)” for the

speaker setup (➔ page 38).

The AV receiver’s listening modes can transform your

listening room into a movie theater or concert hall, with

high fidelity and stunning surround sound.

This is mono (monophonic) sound.

This is stereo (stereophonic) sound. Two

independent audio signal channels are reproduced

through two speakers.

■ Explanatory Notes

This is 5.1-channel surround sound. This surround

system has five main channels of sound and a sixth

subwoofer channel (called the point-one channel).

*1 This is 7.1-channel surround sound. This is a further

sound enhancement to 5.1-channel sound with two

additional speakers that provide greater sound

envelopment and more accurate positioning of

sounds.

The AV receiver outputs this source in 5.1-channel surround

sound.

a Front speakers

b Center speaker

c Surround speakers

d Subwoofer

En-27

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

■ Onkyo-Original DSP Listening Modes

Listening Mode

Description

Input

Source

Speaker

Layout

Listening Mode

Description

Input

Source

Speaker

Layout

T-D (Theater-

Dimensional)^*1

With this mode you can enjoy a virtual

surround sound even with only two or three

speakers. This works by controlling how

sounds reach the listener’s left and right ears.

Good results may not be possible if there’s

too much reverb, so we recommend that you

use this mode in an environment with little

or no natural reverb.

ZXC

Orchestra^*1

Suitable for classical or operatic music, this

mode emphasizes the surround channels in

order to widen the stereo image, and

simulates the natural reverberation of a large

hall.

T – D

O r c h e s t r a

Unplugged^*1

Suitable for acoustic instruments, vocals,

and jazz, this mode emphasizes the front

stereo image, giving the impression of being

right in front of the stage.

U n p l u g g e d

Studio-Mix^*1

Suitable for rock or pop music, listening to

music in this mode creates a lively sound

field with a powerful acoustic image, like

being at a club or rock concert.

S t u d i o – M i x

TV Logic^*1

This mode adds realistic acoustics to TV

shows produced in a TV studio, surround

effects to the entire sound, and clarity to

voices.

T V L o g i c

Game-RPG^*1

G a m e – R P G

In this mode, the sound has a dramatic feel

with a similar atmosphere to Orchestra

mode.

Game-Action^*1

In this mode, sound localization is distinct

with emphasis on bass.

G a m e – A c t i o n

Game-Rock^*1

In this mode, sound pressure is emphasized

to heighten live feel.

G a m e – R o c k

Game-Sports^*1

In this mode, reverberation is increased and

sound localization decreased slightly.

G a m e – S p o r t s

All Ch Stereo

Ideal for background music, this mode fills

the entire listening area with stereo sound

from the front and surround speakers.

A l

C h S t e r e o

Full Mono

In this mode, all speakers output the same

sound in mono, so the sound you hear is the

same regardless of where you are within the

listening room.

F u l

M o n o

En-28

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

■ Listening Modes

Listening Mode

DSD^*2

Description

Input

Source

Speaker

Layout

Listening Mode

Description

Input

Source

Speaker

Layout

In this mode, audio from the input source is

output without surround-sound processing.

The speaker configuration (presence of

speakers), crossover frequency, speaker

distance, A/V Sync and much of the

processing set via Home menu are enabled.

See “On-screen Setup” for more details

(➔ page 35).

Direct

In this mode, audio from the input source is

output without surround-sound processing.

The speaker configuration (presence of

speakers) and speaker distance settings are

enabled, but much of the processing set via

Home menu is disabled. A/V Sync does not

have effect on the analog audio. See “On-

screen Setup” for more details

ZXC

D S D

Dolby Digital

D i r e c t

D o l b y

Dolby Digital Plus^*3

D o l b y

Dolby TrueHD

(➔ page 35).

D o l b y T r u e H D

Stereo

Sound is output from the front left and right

speakers and subwoofer.

DTS

S t e r e o

D T S

Mono

Use this mode when watching an old movie

with a mono soundtrack, or use it with the

foreign language soundtracks recorded in the

left and right channels of some movies. It

can also be used with DVDs or other sources

containing multiplexed audio, such as

karaoke DVDs.

DTS-HD High

Resolution Audio

M o n o

D T S – H D H R

DTS-HD Master

Audio

Multichannel

This mode is for use with PCM multichannel

sources.

D T S – H D MS T R

DTS Express

M u l

i c h

D T S E x p r e s s

DTS 96/24

This mode is for use with DTS 96/24

sources. This is high-resolution DTS with a

96 kHz sampling rate and 24-bit resolution,

providing superior fidelity. Use it with

DVDs that bear the DTS 96/24 logo.

D T S 9 6 / 2 4

En-29

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Listening Mode

Description

Input

Source

Speaker

Layout

Note

These listening modes cannot be selected during USB or iPod playback.

Dolby Pro Logic II

Dolby Pro Logic II expands any 2-channel

source for 5.1-channel playback. It provides

a very natural and seamless surround-sound

experience that fully envelops the listener.

As well as music and movies, video games

can also benefit from the dramatic spatial

effects and vivid imaging.

The AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player

side to PCM might obtain a better sound according to the player. In that case, set the output setting

on the player side to PCM.

For the Blu-ray Discs, Dolby Digital is used.

• The listening modes cannot be selected with some source formats.

• Dolby PLII Movie

P L

M o v i e

M u s i c

G a m e

Use this mode with DVDs and videos that

bear the Dolby Surround logo or TV shows

that feature Dolby Surround. You can also

use this mode with stereo movies or TV

shows and the AV receiver will create a 5.1

surround mix from the 2-channel stereo.

• Dolby PLII Music

Use this mode to add 5.1 surround to stereo

sources such as music CDs and DVDs.

• Dolby PLII Game

Use this mode when playing game discs.

Neo:6

This mode expands any 2-channel source for

up to 5.1-channel playback. It uses seven

full-bandwidth channels of matrix decoding

for matrix-encoded material, providing a

very natural and seamless surround sound

experience that fully envelops the listener.

• Neo:6 Cinema

Use this mode with any stereo movie (e.g.,

TV, DVD, VHS).

N e o : 6 C i n e m a

N e o : 6 M u s i c

• Neo:6 Music

Use this mode with any stereo music source

(e.g., CD, radio, cassette, TV, VHS, DVD).

En-30

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

■ Info

Using the Home Menu

Selecting Speakers A and B

`You can view the information of the following

The Home menu provides quick access to frequently used

settings. You can change settings and view the current

information.

You can use two sets of front speakers with the AV

receiver: Speakers A for up to 5.1-channel playback in

your main listening room and Speakers B for 2-channel

stereo playback in another room.

items: “Input” and “Output”.

■ Listening Mode

`You can select the listening modes that are

grouped in the following categories:

The on-screen menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected

to other video outputs, use the AV receiver’s display

when changing settings.

“MOVIE/TV”, “MUSIC” and “GAME”.

Use q/wto select the category and e/rto

select the listening mode. Press ENTER to

switch to the selected listening mode.

Press RECEIVER once followed by SP A/B

repeatedly to cycle through the selection:

Speakers A → Speakers A&B → Speakers B

Off ←

Speaker indicators and output channels are shown

below.

Note

• The on-screen menus are displayed when:

– There is no video input, or

– The video input is 480p, 576p, 720p, 1080i, or 1080p.

Depending on the input source and listening mode, not all

channels shown here output the sound.

• This setting is not available in either of the following cases:

– The “Audio TV Out” setting is set to “On” (➔ page 43).

– “HDMI Ctrl (RIHD)” is set to “On” (➔ page 43) and

you’re listening through your TV speakers.

Speaker indicators Output channel

Speakers A: 5.1 channels

Press RECEIVER followed by HOME.

The Home menu will be superimposed on the TV

screen.

Speakers A: 2.1 channels

Speakers B: 2 channels

Use q/wand ENTER to make the desired selection.

No sound

■ Input

While Speakers B is on, channels are reduced to 2.1 in the

main room.

`You can select the input source.

Use q/wto select the desired input source.

Pressing ENTER switches to the selected input

source.

Tip

• Alternatively, you can use the AV receiver’s SPEAKERS

A and B.

■ Audio

`You can change the following settings: “Bass”,

“Treble”, “Subwoofer Level”, “Center Level”,

“Late Night”, “Music Optimizer”, and “Cinema

Filter”.

See also:

• “Using the Audio Settings” (➔ page 44)

En-31

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Using the Sleep Timer

Setting the Display Brightness

Displaying Source Information

With the sleep timer, you can set the AV receiver to turn

off automatically after a specified period.

You can adjust the brightness of the AV receiver’s display.

You can display various information about the current

input source as follows.

Press RECEIVER once followed by DIMMER

repeatedly to switch between: normal, dim, or

Press RECEIVER once followed by SLEEP

Press RECEIVER once followed by DISPLAY

repeatedly to cycle through the available

information.

repeatedly to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10

minute steps.

dimmer brightness.

Tip

• Alternatively, you can use the AV receiver’s DIMMER.

The SLEEP indicator lights on the AV receiver’s

display when the sleep timer has been set. The

specified sleep time appears for about 5 seconds, then

the previous display reappears.

• Alternatively, you can use the AV receiver’s DISPLAY.

The following information can typically be displayed.

Input source &

volume^*1

Tip

• If you need to cancel the sleep timer, press SLEEP

repeatedly until the SLEEP indicator goes off.

• To check the time remaining until the AV receiver sleeps,

press SLEEP. Note that if you press again on SLEEP as

the time being displayed is equal to 10 minutes or less, the

sleep timer will go off.

Listening mode

Signal format^*2

or sampling

frequency

When AM or FM radio is used, the band, frequency, and preset

number are displayed.

If the input signal is digital, the signal format is displayed.

Information is displayed for about three seconds, then the

previously displayed information reappears.

En-32

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Changing the Input Display

Using the Music Optimizer

Muting the AV Receiver

The Music Optimizer function enhances the sound quality

of compressed music files.

You can temporarily mute the output of the AV receiver.

When you connect an u-capable Onkyo component, you

must configure the input display so that ucan work

properly.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

Press MUSIC OPTIMIZER on the front panel.

The M.Opt indicator lights on the AV receiver’s

This setting can be done only from the front panel.

flashes on the AV receiver’s display.

display.

Press TV/CD, GAME or VCR/DVR.

“TV/CD”, “GAME” or “VCR/DVR” appears on the

Tip

• To unmute, press MUTING again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is

set to standby.

AV receiver’s display.

• Alternatively, you can use the remote controller’s HOME.

• See “Music Optimizer” for more details (➔ page 45).

Press and hold down the same button (about

3 seconds) to change the input display.

Repeat this step to select the desired input display.

■ TV/CD:

TV/CD → DOCK

→

TAPE

■ GAME:

GAME ↔ DOCK

■ VCR/DVR: VCR/DVR ↔ DOCK

Note

• “DOCK” can be selected for the “TV/CD”, “GAME” or

“VCR/DVR” input selector, but not at the same time.

• Enter the appropriate remote control code before using the

remote controller for the first time (➔ page 48).

En-33

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning On & Basic Operations

Using Headphones

Recording

This section explains how to record the selected input

source to a component with recording capability.

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the PHONES

jack.

AV Recording

Note

Audio sources can be recorded to a recorder (e.g., cassette

tape deck, CDR, MD recorder). Video sources can be

recorded to a video recorder (e.g., VCR, DVD recorder).

• Always turn down the volume before connecting your

headphones.

• While the headphones plug is inserted in the PHONES

jack, the speakers are turned off.

• When you connect a pair of headphones, the listening mode

is set to Stereo, unless it’s already set to Stereo, Mono, or

Direct.

• If you connect an iPod or iPhone to the USB port on the AV

receiver, no sound will be output from the headphones jack.

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV

receiver’s MASTER VOLUME control has no effect

on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording,

that input source will be recorded.

En-34

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Explanatory Notes

Common Procedures in Setup Menu

On-screen Setup

Sp Config

The setup menus provides a convenient way to change the

AV receiver’s various settings. Settings are organized into

10 categories.

Remote indicator

■ Subwoofer

`Yes

`No

The on-screen menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected

to other video outputs, use the AV receiver’s display

when changing settings.

RECEIVER

a Menu selection

b Setting target

ENTER

c Setting options (default setting underlined)

q/w/e/r

This section describes the procedure for using the

remote controller unless otherwise specified.

SETUP

RETURN

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

BD/DVD

VCR/DVR

CBL/SAT

GAME

Note

• The on-screen menus are displayed when:

– There is no video input, or

– The video input is 480p, 576p, 720p, 1080i, or 1080p.

Press RECEIVER followed by SETUP.

AUX

TUNER

TV/CD

Use q/wto select a menu item, and then press

7. Audio Adjust

8. Source Setup

9. Hardware

ENTER.

Use q/wto select a setting target, and use e/rto

Setting target

change the setting.

10. HDMI Setup

Press SETUP to close the menu.

Press RETURN to return to the previous menu.

Note

• This procedure can also be performed on the AV receiver by

using SETUP, the cursor buttons, and ENTER.

En-35

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Menu item

Setting target

Left

Setup menu items

Level Cal

(➔ page 39)

Center

Menu item

Setting target

Right

HDMI Input

(➔ page 37)

BD/DVD

VCR/DVR

CBL/SAT

GAME

Surround Right

Surround Left

Subwoofer

Audio Adjust

(➔ page 40)

Input Ch (Mux)

Input Ch (Mono)

Panorama

AUX

TV/CD

Component

(➔ page 37)

BD/DVD

VCR/DVR

CBL/SAT

GAME

Dimension

Center Width

Center Image

Listening Angle

A/V Sync

AUX

Source Setup

(➔ page 41)

TV/CD

Name

Digital Audio

(➔ page 38)

BD/DVD

VCR/DVR

CBL/SAT

GAME

Audio Selector

Fixed Mode

Volume OSD

Remote ID

Hardware

(➔ page 42)

AUX

AM/FM Freq Step

Auto Standby

HDMI Ctrl (RIHD)

HDMI Through

Audio TV Out

Audio Return Ch

LipSync

TV/CD

Sp Config

(➔ page 38)

Subwoofer

Front

HDMI Setup

(➔ page 43)

Center

Surround

Crossover

Double Bass

Unit

Sp Distance

(➔ page 39)

Left

Center

Right

Surround Right

Surround Left

Subwoofer

En-36

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Note

HDMI Input

Component (Component Video Input)

• If no video component is connected to HDMI output (even if the

HDMI input is assigned), the AV receiver selects the video

source based on the setting of “Component (Component Video

Input)”.

• When an HDMI IN is assigned to an input selector as explained

here, the same HDMI IN will be set as a priority in the “Digital

Audio (Digital Audio Input)” (➔ page 38). In this case, if you

want to use the coaxial or optical audio input, make the

appropriate selection in the “Audio Selector” setting

(➔ page 41).

• Do not assign an HDMI IN to the TV/CD selector while “HDMI

Ctrl (RIHD)” is set to “On” (➔ page 43), otherwise

appropriate CEC (Consumer Electronics Control) operation will

not be guaranteed.

• If you assign “- - - - -” to an input selector that is currently

selected in “HDMI Through” (➔ page 43), the “HDMI

Through” setting will be automatically switched to “Off”.

• The “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

HDMI Input

Component

If you connect a video component to an HDMI input, you

must assign that input to an input selector. For example, if

you connect your Blu-ra y Disc/DVD player to HDMI IN 2,

you must assign “HDMI2” to the “BD/DVD” input

selector.

If you connect a video component to a component video

input, you must assign that input to an input selector. For

example, if you connect your Blu-ray Disc/DVD player to

COMPONENT VIDEO IN 2, you must assign “IN2” to

the “BD/DVD” input selector.

Here are the default assignments.

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

HDMI1

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

IN1

HDMI2

- - - - -

IN2

HDMI3

HDMI4

- - - - -

AUX

- - - - -

AUX

TV/CD

- - - - -

TV/CD

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

`HDMI1, HDMI2, HDMI3, HDMI4:

Select the input to which the component has been

connected.

`IN1, IN2:

Select the input to which the component has been

connected.

`- - - - -:

Select if you’re not using the HDMI OUT.

Each HDMI input cannot be assigned to two input

selectors or more. When HDMI1 - HDMI4 have already

been assigned, you must first set any unused input

selectors to “- - - - -” or you will be unable to assign

HDMI1 - HDMI4 to input selector.

Select if you’re not using the COMPONENT

VIDEO OUT.

Note

• The “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

En-37

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

■ Front

`Small:

`Large:

Digital Audio (Digital Audio Input)

Sp Config (Speaker Configuration)

Select based on the cone diameter.

Note

Digital Audio

Sp Config

• If the “Subwoofer” setting is set to “No”, this setting is fixed to

“Large”.

If you connect a component to a digital audio input, you

must assign that input to an input selector. For example, if

you connect your CD player to the OPTICAL IN 1, you

must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

This section explains how to specify which speakers are

connected and their sizes.

■ Center , Surround

`Small:

`Large:

Select based on the cone diameter.

Cone diameter

`None

Input selector

BD/DVD

VCR/DVR

CBL/SAT

GAME

Default assignment

COAXIAL

- - - - -

Note

If the “Front” setting is set to “Small”, the “Large” option

cannot be selected.

For speakers with a cone diameter larger than 6-1/2 inches

(16 cm), specify Large (full band). For those with a

smaller diameter, specify Small (default crossover

100 Hz).

The crossover frequency can be changed in the “Crossover

(Crossover Frequency)”.

- - - - -

OPTICAL1

- - - - -

■ Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you

specified as “Small” in the “Sp Config (Speaker

Configuration)”. To get the best bass performance from

your speaker system, you need to set the crossover

frequency according to the size and frequency response

of your speakers.

`40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,

120Hz, 150Hz, 200Hz

Use the diameter of the smallest speaker in your system

when choosing the crossover frequency.

AUX

TV/CD

OPTICAL2

■ BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD

`COAXIAL, OPTICAL1, OPTICAL2:

Select the input to which the component has been

connected.

Note

• These settings are not available in either of the following cases:

– A pair of headphones is connected.

– The “Audio TV Out” setting is set to “On” (➔ page 43).

– “HDMI Ctrl (RIHD)” is set to “On” (➔ page 43) and you’re

listening through your TV speakers.

`- - - - -:

Select if the component is connected to an analog

audio input.

– Speakers B is on.

– Speakers A is off.

Speaker cone diameter

Over 8 in. (20 cm)

Crossover frequency

Note

■ Subwoofer

`Yes

`No

40/50/60 Hz

• When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ page 37), the same HDMI IN will be set as

a priority in this assignment. In this case, if you want to use the

coaxial or optical audio input, make the appropriate selection in

the “Audio Selector” (➔ page 41).

• Supported sampling rates for PCM signals (stereo/mono) from a

digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,

20, 24 bit.

6-1/2 to 8 in. (16 to 20 cm)

5-1/4 to 6-1/2 in. (13 to 16 cm)

3-1/2 to 5-1/4 in. (9 to 13 cm)

Under 3-1/2 in. (9 cm)

70/80/90 Hz

100 Hz

120 Hz

150/200 Hz

Choose the setting suitable for the speaker.

• The “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

To be continued

En-38

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Note

Sp Distance (Speaker Distance)

Level Cal (Level Calibration)

• For a more accurate setting, look up the frequency response in the

manuals supplied with your speakers and set accordingly.

• Choose a higher crossover frequency if you want more sound

from your subwoofer.

Sp Distance

Level Cal

■ Double Bass

`On

`Off

Here you can specify the distance from each speaker to the

listening position so that the sound from each speaker

arrives at the listener’s ears as the sound designer intended.

Here you can adjust the level of each speaker with the

built-in test tone so that the volume of each speaker is the

same at the listening position.

Turn this setting on to boost bass output by feeding bass

sounds from the front left, right, and center channels to the

subwoofer.

Note

• These settings are not available in either of the following cases:

– A pair of headphones is connected.

• These settings cannot be calibrated in either of the following

cases:

Note

– The “Audio TV Out” setting is set to “On” (➔ page 43).

– “HDMI Ctrl (RIHD)” is set to “On” (➔ page 43) and you’re

listening through your TV speakers.

– Speakers B is on.

– Speakers A is off.

– A pair of headphones is connected.

– The “Audio TV Out” setting is set to “On” (➔ page 43).

– “HDMI Ctrl (RIHD)” is set to “On” (➔ page 43) and you’re

listening through your TV speakers.

– Speakers B is on.

• When the “Subwoofer” setting is set to “No” or the “Front”

setting to “Small” (➔ page 38), this setting is fixed to “Off”.

• This setting is set to “On” automatically when the “Subwoofer”

and “Front” settings are set for the first time to “Yes” and

“Large” respectively.

– Speakers A is off.

– The AV receiver is muted.

■ Unit

`feet:

■ Left, Center , Right, Surround Right, Surround

Left

Distances can be set in feet. Range: 1ft to 30ft in

1 foot steps.

`meters:

`–12 dB to 0 dB to +12 dB in 1 dB step.

Distances can be set in meters. Range: 0.3m to 9.0m

in 0.3 meter steps.

■ Subwoofer

`–15 dB to 0 dB to +12 dB in 1 dB step.

■ Left, Center, Right, Surround Right, Surround

Left, Subwoofer

Note

• Speakers that you set to “No” or “None” in the “Sp Config

`Specify the distance from the each speaker to your

listening position.

(Speaker Configuration)” (➔ page 38) cannot be selected.

For the center speaker and subwoofer, the level settings made

by using the Home menu are saved in this menu (➔ page 44).

Note

Tip

• Speakers that you set to “No” or “None” in the “Sp Config

(Speaker Configuration)” (➔ page 38) cannot be selected.

• If you’re using a handheld sound level meter, adjust the level of

each speaker so that it reads 75 dB SPL at the listening position,

measured with C-weighting and slow reading.

En-39

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Dolby

DTS

Audio Adjust

■ PL II Music (2ch Input)

These settings apply to only 2-channel stereo sources.

■ Neo:6 Music

Center Image

Panorama

`On

`Off

`0 to 2 to 5

Audio Adjust

With this setting, you can specify by how much the front

left and right channel output is attenuated in order to create

the center channel.

Changing the value from “0” to “5” will spread the sound

of the center channel to left and right (outwards).

With the Audio Adjust functions and settings, you can

adjust the sound and listening modes as you like.

With this setting, you can broaden the width of the front

stereo image when using the Dolby Pro Logic II Music

listening mode.

Multiplex/Mono

Dimension

`–3 to 0 to +3

Theater-Dimensional

■ Multiplex

With this setting, you can move the sound field forward or

backward when using the Dolby Pro Logic II Music

listening mode. Higher settings move the sound field

backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much

surround sound, move the sound field forward to improve

the balance. Conversely, if the stereo image feels like it’s

in mono, or there’s not enough surround sound, move it

backward.

Input Ch (Mux)

`Main

`Sub

`Main/Sub

This setting determines which channel of a stereo

multiplex source is output. Use it to select audio channels

or languages with multiplex sources, multilingual TV

broadcasts, and so on.

■ Listening Angle

`Wide:

Select if the listening angle is 40 degrees.

`Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-

Dimensional listening mode by specifying the angle of the

front left and right speakers relative to the listening

position. Ideally, the front left and right speakers should be

equidistant from the listening position and at an angle close

to one of the two available settings.

■ Mono

Center Width

`0 to 3 to 7

Input Ch (Mono)

`Left + Right

`Left

`Right

This setting specifies the channel to be used for playing

any 2-channel digital source such as Dolby Digital, or 2-

channel analog/PCM source in the Mono listening mode.

With this setting, you can adjust the width of the sound

from the center speaker when using the Dolby Pro Logic II

Music listening mode. Normally, if you’re using a center

speaker, the center channel sound is output from only the

center speaker. (If you’re not using a center speaker, the

center channel sound will be distributed to the front left

and right speakers to create a phantom center). This setting

controls the front left, right, and center mix, allowing you

to adjust the weight of the center channel sound.

Front left speaker

Front right speaker

20°/40°

En-40

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Preset Name For Input Selector

Audio Selector

Source Setup

■ Name

■ Audio Selector

`ARC:

`- - -, Blu-ray, DVD, HD DVD, VCR, DVR, Tivo,

CableSTB, SAT STB, PS3, Wii, Xbox, PC, TV, CD,

TAPE, iPod:

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

Items can be set individually for each input selector.

To reset to the default, select “- - -”.

You can enter a preset name for each individual input

selector for easy identification. When entered, the preset

name will be displayed.

With this selection, the TV’s audio can be

automatically selected as a priority among other

assignments.

Preparation

Press the input selector buttons to select an input source.

`HDMI:

This can be selected when HDMI IN has been

assigned as an input source. If both HDMI (HDMI

IN) and digital audio inputs (COAXIAL IN or

OPTICAL IN) have been assigned, HDMI input is

automatically selected as a priority.

Source Setup

Note

• You can’t assign the same preset name to multiple input selectors.

• This setting cannot be used for the AM, FM or USB input

selector.

A/V Sync

■ A/V Sync

`COAXIAL:

`0 ms to 400 ms in 10 msec steps

This can be selected when COAXIAL IN has been

assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is

automatically selected as a priority.

When using progressive scanning on your Blu-ray

Disc/DVD player, you may find that the picture and sound

are out of sync. With this setting, you can correct this by

delaying the audio signals.

To view the TV picture while setting the delay, press

ENTER.

`OPTICAL:

This can be selected when OPTICAL IN has been

assigned as an input source. If both optical and HDMI

inputs have been assigned, optical input is

automatically selected as a priority.

To return to the previous screen, press RETURN.

The range of values you can adjust will depend on whether

your TV supports HDMI Lip Sync and if the “LipSync”

setting is set to “On” or not (➔ page 44).

`Analog:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both

digital and analog inputs.

Note

• A/V Sync is disabled when the Direct listening mode is used with

an analog input source.

Note

• This setting can be made only for the input source that is assigned

as HDMI IN, COAXIAL IN, or OPTICAL IN.

You can select “ARC” if you select the TV/CD input selector.

But you cannot if you’ve selected “Off” in the “Audio Return

Ch” setting (➔ page 44).

En-41

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Setting the Incoming Digital Signal (Fixed

Mode)

Tuner

Hardware

■ AM/FM Freq Step

`10kHz/200kHz:

`9kHz/50kHz:

■ Fixed Mode

`Off:

The format is detected automatically. If no digital

input signal is present, the corresponding analog

input is used instead.

Select the frequency step according to your area.

For AM/FM tuning to work properly, you must specify the

AM/FM frequency step used in your area.

Hardware

OSD

`PCM:

Note

■ Volume OSD

`On

`Off

Turn this setting on to display the volume level on the TV

screen while it is adjusted.

Only 2-channel PCM format input signals will be

heard. If the input signal is not PCM, the PCM

indicator will flash and noise may also be produced.

`DTS:

Only DTS (but not DTS-HD) format input signals

will be heard. If the input signal is not DTS, the dts

indicator will flash and there will be no sound.

When “HDMI”, “COAXIAL” or “OPTICAL” is selected

in the “Audio Selector” setting, you can then specify the

signal type in “Fixed Mode”.

Normally, the AV receiver detects the signal format

automatically. However, if you experience either of the

following issues when playing PCM or DTS material, you

can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off,

try setting the format to PCM.

• When this setting is changed, all radio presets will be deleted.

Auto Standby

■ Auto Standby

`Off

`On

When “Auto Standby” is set to “On”, the AV receiver

will automatically enter standby mode if there is no

operation for 30 minutes with no audio and no video signal

input.

“Auto Standby” will appear on the AV receiver’s display

and OSD 30 seconds before the Auto Standby comes on.

Remote ID

■ Remote ID

`1, 2, or 3

When several Onkyo components are used in the same

room, their remote ID codes may overlap. To differentiate

the AV receiver from the other components, you can

change its remote ID from “1”, to “2” or “3”.

Note

• Set to “On”, the Auto Standby function may activate itself during

playback with some sources.

• If you do change the AV receiver’s remote ID, be sure to change

the remote controller to the same ID (see below), otherwise, you

won’t be able to control it with the remote controller.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

Changing the remote controller’s ID

• The setting will be reset to “Off” when you change the setting in

the “Audio Selector” (➔ page 41).

While holding down RECEIVER, press and hold

down SETUP until the remote indicator lights

(about 3 seconds).

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

En-42

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

■ Audio TV Out

`Off

`On

This preference determines whether the incoming audio

signal is output from the HDMI output. You may want to

turn this preference on if your TV is connected to the

HDMI output and you want to listen to the audio from a

connected component through your TV’s speakers.

Normally, this should be set to “Off”.

• When the source equipment is connected with the u

connection, it may malfunction if “HDMI Ctrl (RIHD)” is set to

“On”.

HDMI Setup

■ HDMI Through

`Off

HDMI Setup

`BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX,

TV/CD:

Selects the input source for which the HDMI

Through function is enabled.

`Last:

■ HDMI Ctrl (RIHD)

`Off

`On

Note

The HDMI Through function is activated on the input

source selected at the time of setting the AV receiver

to standby mode.

• If “On” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this

case, “TV Speaker” appears on the AV receiver’s display by

pressing DISPLAY.

• When “HDMI Ctrl (RIHD)” is set to “On”, this setting is fixed

to “Auto”.

Turn this setting on to allow p-compatible

components connected via HDMI to be controlled by the

AV receiver (➔ page 58).

When enabling the HDMI Through function, regardless of

whether the AV receiver is on or in standby, both audio

and video streams from an HDMI input will be output to

the TV or other components via HDMI connection. In

standby mode, the HDMI THRU and HDMI indicators

will light (HDMI will be dimly-lit).

This setting is fixed to “Auto” automatically when the

above “HDMI Ctrl (RIHD)” setting is set to “On”,

resulting in automatic input source selection.

Note

• When the setting is set to “On” and the menu is closed, the names

of connected p-compatible components and “RIHD On”

are displayed on the AV receiver.

• With some TVs and input signals, no sound may be output even

when this setting is set to “On”.

• When “Audio TV Out” or “HDMI Ctrl (RIHD)” is set to “On”

and you’re listening through your TV’s speakers (➔ page 15),

turning up the AV receiver’s volume control will make the sound

be output from the AV receiver’s front left and right speakers. To

stop the AV receiver’s speakers producing sound, change the

settings, change your TV’s settings, or turn down the AV

receiver’s volume.

“Search…” → “(name)” → “RIHD On”

When the AV receiver cannot receive the name of the component,

it is displayed as “Player^*” or “Recorder^*”, etc (“ ” shows up

and indicates the number of components, when two or more are

received).

• When an p-compatible component is connected to the

AV receiver via an HDMI cable, the name of the connected

component is displayed on the AV receiver. For example, while

you are watching TV broadcasting, if you operate a Blu-ray

Disc/DVD player (being powered on) with the remote control of

the AV receiver, the name of the Blu-ray Disc/DVD player will

be displayed on the AV receiver.

• Set it to “Off” when a connected piece of equipment is not

compatible or it is unclear whether the equipment is compatible

or not.

Note

• Only the input source assigned to the HDMI IN via

“HDMI Input” is enabled (➔ page 37).

• The power consumption in standby mode will increase during the

HDMI Through function; however in the following cases, the

power consumption can be saved:

• Listening mode cannot be changed when this setting is set to

“On” and the input source is not HDMI.

– The TV is in standby mode.

– You are watching a TV program.

• Refer to the connected component’s instruction manual for

details.

• Depending on the connected component, the correct input source

may not be selected with the setting fixed to “Auto”.

• This setting is set to “Off” automatically when the “HDMI Ctrl

(RIHD)” setting is set to “Off”.

• If operation is not normal when set to “On”, change the setting to

“Off”.

• Refer to the connected component’s instruction manual for

details.

• When the “HDMI Ctrl (RIHD)” setting is set to “On”, the power

consumption in standby mode slightly increases. (Depending on

the TV status, the AV receiver will enter standby mode as usual.)

En-43

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

■ Audio Return Ch (ARC)

`Off

Speaker Levels

Using the Audio Settings

■ Subwoofer Level

`Auto:

You can change various audio settings from the Home

The audio signal from your TV tuner can be sent to

the HDMI OUT of the AV receiver.

The audio return channel (ARC) function allows an ARC

capable TV to send the audio stream to the HDMI OUT of

the AV receiver. To use this function, you must select the

TV/CD input selector and your TV must be ARC capable.

Default setting: “- - - -”

menu (➔ page 31).

`–15 dB to 0 dB to +12 dB in 1 dB steps

■ Center Level

Press RECEIVER followed by HOME.

`–12 dB to 0 dB to +12 dB in 1 dB steps

You can adjust the volume of each speaker while listening

to an input source.

These temporary adjustments are cancelled when the AV

receiver is set to standby. To save the setting you made

here, go to “Level Cal (Level Calibration)” (➔ page 39)

before setting the AV receiver to standby.

Use q/wand ENTER to select “Audio”, and then

use q/w/e/rto make the desired selection.

Note

• These settings are not available in either of the following cases:

– The “Audio TV Out” setting is set to “On” (➔ page 43).

– “HDMI Ctrl (RIHD)” is set to “On” (➔ page 43) and you’re

listening through your TV speakers.

• This setting is fixed to “- - - -” when the “HDMI Ctrl (RIHD)”

setting is set to “Off”.

Note

• This setting is set to “Auto” automatically when the “HDMI Ctrl

(RIHD)” setting is set to “On” for the first time.

• If you set “Audio Return Ch” to “Auto”, the “Audio Selector”

settings of the TV/CD input selector will be automatically

switched to “ARC” (➔ page 41).

• These settings cannot be calibrated in either of the following

cases:

– A pair of headphones is connected.

Tone Control

– The AV receiver is muted.

• Speakers that are set to “No” or “None” in the “Sp Config

(Speaker Configuration)” (➔ page 38) cannot be adjusted.

■ Bass

■ LipSync

`Off

`On

`–10 dB to 0 dB to +10 dB in 2 dB steps

You can boost or cut low-frequency sounds output

from the front speakers.

This function allows the AV receiver to automatically

correct any delay between the video and the audio, based

on the data from the connected monitor.

■ Treble

`–10 dB to 0 dB to +10 dB in 2 dB steps

You can boost or cut high-frequency sounds output

from the front speakers.

You can adjust the bass and treble for Speakers A and B

front speakers, except when the Direct listening mode is

selected.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

After changing the settings of the “HDMI Ctrl

(RIHD)”, “HDMI Through” or “Audio Return Ch”

turn off the power on all connected pieces of equipment

and then turn them on again. Refer to the user’s manuals

for all connected pieces of equipment.

Operating on the remote controller directly

Press RECEIVER once followed by TONE

repeatedly to select either “Bass” or “Treble”.

Use – and + to adjust.

Tip

• Alternatively, you can use the AV receiver’s TONE and –/+.

En-44

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Operations

Late Night

Music Optimizer

CinemaFILTER

■ Late Night

■ Music Optimizer

■ Cinema Filter

For Dolby Digital and Dolby Digital Plus sources, the

`Off

options are:

`On

`Off

`Low:

The Music Optimizer function enhances the sound quality

of compressed music files. The M.Opt indicator lights on

the AV receiver’s display.

Turn this setting on to soften overly bright movie

soundtracks, which are typically mixed for reproduction in

a movie theater.

Small reduction in dynamic range.

`High:

CinemaFILTER can be used with the following listening

modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,

Dolby Pro Logic II Movie, Multichannel, DTS, DTS Neo:6

Cinema, DTS 96/24, DTS-HD High Resolution Audio,

DTS-HD Master Audio and DTS Express.

Tip

Large reduction in dynamic range.

• Alternatively, you can use the AV receiver’s MUSIC

OPTIMIZER.

For Dolby TrueHD sources, the options are:

`Auto:

The Late Night function is set to “On” or “Off”

automatically.

`Off

`On

Turn this setting on to reduce the dynamic range of Dolby

Digital material so that you can still hear quiet parts even

when listening at low volume levels—ideal for watching

movies late at night when you don’t want to disturb

anyone.

Note

• The Music Optimizer function only works with PCM digital

audio input signals with a sampling rate below 48 kHz and analog

audio input signals.

• The Music Optimizer is disabled when the Direct listening mode

is selected.

Note

• The CinemaFILTER may not work when used with certain input

sources.

• The setting is stored individually for each input selector.

Note

• The effect of the Late Night function depends on the material that

you are playing and the intention of the original sound designer,

and with some material there will be little or no effect when you

select the different options.

• The Late Night function can be used only when the input source

is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “Off” when the AV receiver is

set to standby. For Dolby TrueHD sources, it will be set to

“Auto”.

En-45

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

■ System Function

■ Operating Notes

• Use the AV receiver’s volume control to adjust the playback

volume.

• While your iPod/iPhone is inserted in the RI Dock, its volume

control has no effect.

• If you do adjust the volume control on your iPod/iPhone while

it’s inserted in the RI Dock, be careful that it’s not set too loud

before you reconnect your headphones.

iPod/iPhone Playback

via Onkyo Dock

System On

When you turn on the AV receiver, the RI Dock and

iPod/iPhone turn on automatically. In addition, when RI

Dock and iPod/iPhone are on, the AV receiver can be

turned on by pressing 8.

Using the Onkyo Dock

Auto Power On

The Dock is sold separately. Models sold are different

depending on the region.

For the latest information on the Onkyo Dock

components, see the Onkyo web site at:

http://www.onkyo.com

If you press the remote controller’s 1(Playback) while

the AV receiver is on standby, the AV receiver will

automatically turn on, select your iPod/iPhone as the input

source, and your iPod/iPhone will start playback.

Before using the Onkyo Dock components, update

your iPod/iPhone with the latest software, available

from the Apple web site.

For supported iPod/iPhone models, see the instruction

manual of the Onkyo Dock.

Direct Change

If you start iPod/iPhone playback while listening to another

input source, the AV receiver will automatically switch to

the input to which RI Dock is connected.

Other Remote Operations

You can use the remote controller that came with the AV

receiver to control other iPod/iPhone functions. The

available functionality depends on the AV receiver.

RI Dock

With the RI Dock, you can easily play the music of your

iPod/iPhone, or watch the slideshows and videos of your

iPod/iPhone on a TV. In addition, the on-screen display

(OSD) allows you to view, navigate, and select your

iPod/iPhone model’s contents on your TV, and with the

supplied remote controller, you can control your

iPod/iPhone from the comfort of your sofa. You can even

use the AV receiver’s remote controller to operate your

iPod/iPhone.

iPod/iPhone Alarm

If you use the Alarm function on your iPod/iPhone to start

playback, the AV receiver will turn on at the specified time

and select your iPod/iPhone as the input source

automatically.

Note

• Linked operations do not work with video playback or when the

alarm is set to play a sound.

Note

• If you use your iPod/iPhone with any other accessories,

iPod/iPhone playback detection may not work.

• The System On function may not work depending on the RI

Dock.

• Enter the appropriate remote control code before using the AV

receiver’s remote controller for the first time (➔ page 48).

• Connect the RI Dock to the AV receiver with an ucable

(➔ page 17).

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

• Set the AV receiver’s Input Display to “DOCK” (➔ page 33).

En-46

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

■ uDock operation

Controlling Your iPod/iPhone

Press the appropriate REMOTE

MODE button first.

Available buttons

By pressing the REMOTE MODE button that’s been

programmed with the remote control code for your Dock,

you can control your iPod/iPhone in the Dock with the

buttons described further in this section.

See “Entering Remote Control Codes” for details on

entering a remote control code (➔ page 48).

DISPLAY^*3

a 8

TOP MENU^*2

MUTING

ALBUM +/–

c q/w/e/r, ENTER

PLAYLIST e/r

i VOL q/w

d 1, 3, 2, 5, 4,

7, 6

See the Dock’s instruction manual for more information.

REPEAT

MODE^*4

RI Dock

RANDOM

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

Note

• With some iPod/iPhone models, generations and RI Docks,

certain buttons may not work as expected.

• For detailed operation of iPod/iPhone, please refer to the

• 8may not work with a remote control code (without

u). In this case, make an uconnection and enter the

remote control code 81993 (with u).

instruction manual of the RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI

■ With the RI Control

Dock on or off. Also, your iPod/iPhone may not respond the

first time you press this button, in which case you should press

it again. This is because the remote controller transmits the On

and Standby commands alternately, so if your iPod/iPhone is

already on, it will remain on when the remote controller

transmits the On command. Similarly, if your iPod/iPhone is

already off, it will remain off when the remote controller

transmits the Off command.

Make an uconnection and enter the remote

control code 81993 (with u).

• Set the AV receiver’s Input Display to “DOCK”

(➔ page 33).

■ Without the RI Control

You must enter the remote control code 82990 first

(➔ page 49).

TOP MENU works as the mode button when used with the

DS-A2 RI Dock.

DISPLAY turns on backlight for a second.

Resume mode

With the Resume function, you can resume playback of the

song that was playing when you removed your iPod/iPhone

from the RI Dock.

En-47

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

Entering Remote Control Codes

Remote Control Codes for Onkyo

Controlling Other Onkyo

Components

Components Connected via u

You’ll need to enter a code for each component that you

want to control.

Onkyo components that are connected via uare

controlled by pointing the remote controller at the AV

receiver, not the component. This allows you to control

components that are out of view, in a rack, for example.

You can use the AV receiver’s remote controller to control

your other Onkyo AV components. This section explains

how to enter the remote control code for a component that

you want to control: DVD, CD, etc.

Look up the appropriate remote control code in the

Remote Control Codes for Onkyo Components

Connected via u.

Make sure the Onkyo component is connected with

While holding down the REMOTE MODE button to

Preprogrammed Remote Control

Codes

which you want to assign a code, press and hold

down DISPLAY (about 3 seconds).

The remote indicator lights.

an ucable and an analog audio cable (RCA).

See “Connecting Onkyo uComponents” for details

(➔ page 17).

The following REMOTE MODE butttons are

preprogrammed with remote control codes for controlling

the components listed. You do not need to enter a remote

control code to control these components.

For details on controlling these components, see the

indicated pages.

Note

Enter the appropriate remote control code for a

REMOTE MODE button, by referring to the

previous section.

• Remote control codes cannot be entered for RECEIVER.

• Except for RECEIVER remote control codes from any

category can be assigned to the REMOTE MODE button.

However, these buttons also work as input selector buttons

(➔ page 20), so choose a REMOTE MODE button that

corresponds with the input to which you connect your

component. For example, if you connect your CD player to

the CD input, choose TV/CD when entering its remote

control code.

`42157:

Onkyo cassette tape deck with u

`81993:

BD/DVD Onkyo Blu-ray Disc player (➔ page 50)

Onkyo Dock with u

TV/CD

Onkyo CD player (➔ page 51)

Press the REMOTE MODE button, point the

remote controller at the AV receiver, and operate

the component.

Within 30 seconds, use the number buttons to enter

the 5-digit remote control code.

The remote indicator flashes twice.

If the remote control code is not entered successfully,

the remote indicator will flash once slowly.

To be continued

En-48

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

Controlling Onkyo components without u

If you want to control an Onkyo component by pointing the

remote controller directly at it, or you want to control an

Onkyo component that’s not connected via u, use the

following remote control codes:

`30627:

Resetting the REMOTE MODE Buttons

Resetting the Remote Controller

You can reset a REMOTE MODE button to its default

remote control code.

You can reset the remote controller to its default settings.

While holding down RECEIVER, press and hold

down HOME until the remote indicator lights

While holding down the REMOTE MODE button

that you want to reset, press and hold down HOME

(about 3 seconds).

Onkyo DVD player without u

until the remote indicator lights (about 3 seconds).

Within 30 seconds, press RECEIVER again.

The remote indicator flashes twice, indicating that the

remote controller has been reset.

`71817:

Within 30 seconds, press the REMOTE MODE

button again.

Onkyo CD player without u

`32900/33000:

The remote indicator flashes twice, indicating that the

button has been reset.

Each REMOTE MODE button is preprogrammed

with a remote control code. When a button is reset, its

preprogrammed code is restored.

Onkyo Blu-ray Disc player

`32901/33004:

Onkyo HD DVD player

`70868:

Onkyo MD recorder without u

`71323:

Onkyo CD recorder without u

`82990:

Onkyo Dock without u

En-49

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

■ Blu-ray Disc player / HD-DVD player operation

Controlling Other Components

Press the appropriate REMOTE

MODE button first.

Available buttons

By pressing the REMOTE MODE button that’s been

programmed with the remote control code for your

component, you can control Onkyo component as

described below.

For details on entering a remote control code for other

components, see “Entering Remote Control Codes”

(➔ page 48).

Number: 1 to 9, 0

a 8

Number: +10^*1

DISPLAY

MUTING

DISC +/–

TOP MENU

c q/w/e/r, ENTER

SETUP

e 1, 3, 2, 5, 4,

7, 6

Red (A)

RETURN

AUDIO^*1

CLR

Controlling a Blu-ray Disc/DVD Player, HD

DVD Player

Green (B)

Yellow (C)

Blue (D)

BD/DVD is preprogrammed with the remote control code

for controlling a component that supports the p

■ DVD player operation

(limited to some models). The component must be able to

receive remote control commands via pand be

connected to the AV receiver via HDMI.

Use the following remote control codes:

`32910/33001/31612:

Available buttons

Number: 1 to 9, 0

a 8

TOP MENU

Number: +10^*1

DISPLAY

MUTING

DISC +/–

c q/w/e/r, ENTER

SETUP

Blu-ray Disc/DVD player with p

e 1, 3, 2, 5, 4,

7, 6

The psupported by the AV receiver is the CEC system

SEARCH^*1

RETURN

AUDIO^*1

CLR

control function of the HDMI standard.

REPEAT

RANDOM^*1

MODE^*1

En-50

Download from Www.Somanuals.com. All Manuals Search And Download.

Controlling Other Components

■ CD player / CD recorder / MD recorder operation

Press the appropriate REMOTE

MODE button first.

Available buttons

Number: 1 to 9, 0

a 8

Number: +10

DISPLAY

MUTING

DISC +/–

CLR

c q/w/e/r, ENTER

SETUP

e 1, 3, 2, 5, 4,

7, 6

REPEAT

RANDOM

MODE

■ Cassette tape deck operation

Available buttons

MUTING

a 8

e 1, t(reverse

playback), 2, 5, 4,

7, 6

Note

• With some components, certain buttons may not work as

expected, and some may not work at all.

• See “Controlling Your iPod/iPhone” about the operation of

iPod/iPhone (➔ page 47).

The pfunction is not supported. The p

supported by the AV receiver is the CEC system control

function of the HDMI standard.

En-51

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Audio

The on-screen menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected

to other video outputs, use the AV receiver’s display

when changing settings.

Troubleshooting

■ There’s no sound, or it’s very quiet

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue

yourself, contact your Onkyo dealer.

Press SPEAKERS A or B to turn on the speaker

indicator that you want to output sound.

Make sure that the digital input source is selected

properly.

Power

If you can’t resolve the issue yourself, try resetting the

AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it

on and, while holding down VCR/DVR, press

8ON/STANDBY. “Clear” will appear on the AV

receiver’s display and the AV receiver will enter

standby mode.

Make sure that all audio connecting plugs are pushed 14

in all the way.

■ Can’t turn on the AV receiver

Make sure that the power cord is properly plugged

into the wall outlet.

—

Make sure that the inputs and outputs of all

components are connected properly.

15-17

Unplug the power cord from the wall outlet, wait five

seconds or more, then plug it in again.

Make sure that the polarity of the speaker cables is

correct, and that the bare wires are in contact with the

metal part of each speaker terminal.

■ The AV receiver turns off unexpectedly

Make sure that the input source is properly selected. 20

The AV receiver will automatically enter standby

mode when Auto Standby has been set and launches.

Make sure that the speaker cables are not shorting.

Check the volume. The AV receiver is designed for

home theater enjoyment. It has a wide volume range,

allowing precise adjustment.

—

■ The AV receiver turns off and after restoring the

Note that resetting the AV receiver will delete your radio

presets and custom settings.

power, it turns off again

If the MUTING indicator is flashing on the AV

receiver’s display, press the remote controller’s

MUTING to unmute the AV receiver.

The protection circuit has been activated. Remove the 13

power cord from the wall outlet immediately. Make

sure that all speaker cables and input sources are

properly connected, and leave the AV receiver with

its power cord disconnected for 1 hour. After that,

reconnect the power cord and turn the power on. If

the AV receiver turns off again, unplug the power

cord and contact your Onkyo dealer.

While a pair of headphones is connected to the

PHONES jack, no sound is output from the speakers.

Remote indicator

If there’s no sound from a DVD player connected to

an HDMI IN, check the DVD player’s output

settings, and be sure to select a supported audio

format.

—

Caution: If “CHECK SP WIRE” appears on the AV

receiver’s display, the speaker cables may be

shorting.

RECEIVER

HOME

Check the digital audio output setting on the

connected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

WARNING

If smoke, smell or abnormal noise is produced by the AV

receiver, unplug the power cord from the wall outlet

immediately and contact your Onkyo dealer.

If your turntable uses an MC cartridge, you must

connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are

bent, twisted, or damaged.

To reset the remote controller to its factory defaults,

while holding down RECEIVER, press and hold down

HOME until the remote indicator lights (about 3

seconds). Within 30 seconds, press RECEIVER

again.

Not all listening modes use all speakers.

Specify the speaker distances and adjust the

individual speaker levels.

En-52

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

■ There’s no sound with a certain signal format

■ About DTS signals

If the input signal format is set to “PCM” or “DTS”. 42

Set it to “Off”.

Check the digital audio output setting on the

connected device. On some game consoles, such as

those that support DVD, the default setting is off.

—

When DTS program material ends and the DTS

bitstream stops, the AV receiver remains in DTS

—

■ Only the front speakers produce sound

listening mode and the dts indicator remains on. This

is to prevent noise when you use the pause, fast

forward, or fast reverse function on your player. If

you switch your player from DTS to PCM, you may

not hear any sound because the AV receiver does not

switch formats immediately. In such case, you should

stop your player for about three seconds and then

resume playback.

With some DVD-Video discs, you need to select an

audio output format from a menu.

—

When the Stereo or Mono listening mode is selected, 29

only the front speakers and subwoofer produce

sound.

Depending on the input signal, some listening modes 27-28

cannot be selected.

Make sure the speakers are configured correctly.

■ Can’t get 5.1 playback

■ Only the center speaker produces sound

With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver. This is usually because the DTS bitstream

has been processed (e.g., output level, sampling rate,

or frequency response changed) and the AV receiver

doesn’t recognize it as a genuine DTS signal. In such

cases, you may hear noise.

—

When Speaker B is turned on, Speakers A is reduced 31

to 2.1-channel playback.

If you use the Dolby Pro Logic II Movie, Dolby Pro

Logic II Music, or Dolby Pro Logic II Game listening

mode with a mono source, such as an AM radio

station or mono TV program, the sound is

concentrated in the center speaker.

—

Depending on the number of connected speakers, it is 27-28

not always possible to select all of the listening

modes.

Make sure the speakers are configured correctly.

■ The speaker volume cannot be set as required

■ The surround speakers produce no sound

Playing DTS program material, using the pause, fast

forward, or fast reverse function on your player may

produce a short audible noise. This is not a

malfunction.

After the volume level of each individual speaker has 39

been adjusted, the maximum volume may be reduced.

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround

speakers produce no sound.

—

■ Noise can be heard

Depending on the source and current listening mode, 26

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

Using cable ties to bundle audio cables with power

cords, speaker cables, and the like may degrade the

audio performance, so refrain from doing it.

—

■ The beginning of audio received by an HDMI IN

can’t be heard

Make sure the speakers are configured correctly.

Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio

signals, audio output may not start immediately.

—

An audio cable may be picking up interference. Try

repositioning your cables.

■ The center speaker produces no sound

■ The Late Night function doesn’t work

When the Stereo or Mono listening mode is selected,

the center speaker produces no sound.

—

Make sure the source material is Dolby Digital,

Dolby Digital Plus, or Dolby TrueHD.

Make sure the speakers are configured correctly.

■ The subwoofer produces no sound

The subwoofer outputs no sound while only Speakers 31

B is on. Turn on Speakers A.

When you play source material that contains no

information in the LFE channel, the subwoofer

produces no sound.

—

Make sure the speakers are configured correctly.

En-53

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

■ Can’t control other components

Video

Tuner

If it’s an Onkyo component, make sure that the u

■ There’s no picture

■ Reception is noisy, FM stereo reception is noisy,

or the FM STEREO indicator doesn’t light

cable and analog audio cable are connected properly.

Connecting only an ucable won’t be enough.

Make sure that all video connecting plugs are pushed 14

in all the way.

Make sure you’ve selected the correct remote

controller mode.

10, 50

Relocate your antenna.

—

Make sure that each video component is properly

connected.

15, 17

Move the AV receiver away from your TV or

computer.

For a proper operation of the remote controller as a

cassette tape deck is connected to the TV/CD IN jack,

or as an RI Dock is connected to the TV/CD IN,

VCR/DVR IN or GAME IN jacks, you must set the

input display accordingly.

If the video source is connected to a component video 16, 37

input, you must assign that input to an input selector,

and your TV must be connected to COMPONENT

VIDEO OUT.

Listen to the station in mono.

When listening to an AM station, operating the

remote controller may cause noise.

—

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

—

If you cannot operate it, you will need to enter the

appropriate remote control code.

If the video source is connected to a composite video 16

input, your TV must be connected to the

corresponding composite video output.

If nothing improves the reception, install an outdoor

antenna.

To control an Onkyo component that’s connected via 48

u, point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code

first.

If the video source is connected to an HDMI input,

you must assign that input to an input selector, and

your TV must be connected to the HDMI OUT.

15, 37

Remote Controller

To control an Onkyo component that’s not connected 49

via u, point the remote controller at the component.

Be sure to enter the appropriate remote control code

first.

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

■ The remote controller doesn’t work

Before operating this unit, be sure to press

RECEIVER.

—

■ There’s no picture from a source connected to

an HDMI IN

Make sure that the batteries are installed with the

correct polarity.

uDock for iPod/iPhone

Reliable operation with an HDMI-to-DVI adapter is 60

not guaranteed. In addition, video signals from a PC

are not guaranteed.

Install new batteries. Don’t mix different types of

batteries, or old and new batteries.

■ There’s no sound

Make sure your iPod/iPhone is actually playing.

—

Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor.

■ The on-screen menus don’t appear

Make sure your iPod/iPhone is properly inserted in

the Dock.

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Make sure the AV receiver is turned on, the correct

input source is selected, and the volume is turned up.

—

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

—

When the AV receiver is not connected to a TV via

HDMI OUT, on-screen menus are not displayed.

Make sure the plugs are pushed in all the way.

Try resetting your iPod/iPhone.

—

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

not work reliably when the doors are closed.

—

■ There’s no video

Make sure you’ve selected the correct remote

controller mode.

10, 48

Make sure that your iPod/iPhone model’s TV OUT

setting is set to On.

—

Make sure you’ve entered the correct remote control 48

code.

Make sure the correct input is selected on your TV or

the AV receiver.

Make sure to set the same ID on both the AV receiver 42

and remote controller.

Some versions of the iPod/iPhone do not output

video.

En-54

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

■ The following settings can be made for the

■ The AV receiver’s remote controller doesn’t

control my iPod/iPhone

USB Device Playback

composite video inputs

■ Can’t access the music files on a USB device

You must use the buttons on the unit to make these

settings.

Make sure your iPod/iPhone is properly inserted in

the Dock. If your iP od/iPhone is in a case, it may not

connect properly to the Dock. Always remove your

iPod/iPhone from the case before inserting it into the

Dock.

—

Make sure the USB device is plugged in properly.

—

On the AV receiver, press the input selector for the input

source that you want to set and the SETUP button

simultaneously. While holding down the input selector

button, press SETUP until “Video ATT :On” appears

on the AV receiver’s display. Then, release both buttons.

To turn the setting off, repeat the above process so that

“Video ATT :Off” appears on the AV receiver’s

display, and release the buttons.

The AV receiver supports USB devices that support 61

the USB mass storage device class. However,

playback may not be possible with some USB devices

even if they conform to the USB mass storage device

class.

The iPod/iPhone cannot be operated while it’s

displaying the Apple logo.

—

Make sure you’ve selected the right remote mode.

USB memory devices with security functions cannot 23

be played.

When you use the AV receiver’s remote controller,

point it toward your AV receiver.

—

If you still can’t control your iPod/iPhone, start

playback by pressing your iPod/iPhone model’s Play

button. Remote operation should then be possible.

—

• Video Attenuation

Others

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, AUX, or USB input.

If you have a games console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

Video ATT :Off: (default).

Video ATT :On: Gain is reduced by 2 dB.

■ Standby power consumption

Try resetting your iPod/iPhone.

—

In the following cases, the power consumption in

standby mode may reach up to a maximum of 31 W:

– “HDMI Ctrl (RIHD)” setting is set to “On”.

(Depending on the TV status, the AV receiver will

enter standby mode as usual.)

Depending on your iPod/iPhone, some buttons may

not work as expected.

■ The AV receiver unexpectedly selects my

iPod/iPhone as the input source

– The “HDMI Through” setting is set to other than

“Off”.

Always pause iPod/iPhone playback before selecting

a different input source. If playback is not paused, the

Direct Change function may select your iPod/iPhone

as the input source by mistake during the transition

between tracks.

—

■ If the picture on your TV/monitor connected to

the HDMI OUT is unstable, try switching the

DeepColor function off

■ The sound changes when I connect my

headphones

To turn off the DeepColor function, simultaneously

press the CBL/SAT and 8ON/STANDBY buttons on

the AV receiver. While holding down CBL/SAT, press

8ON/STANDBY until “Deep Color: Off” appears on

the AV receiver’s display. Then, release both buttons.

To reactivate the DeepColor function, repeat the above

process until “Deep Color: On” appears on the AV

receiver’s display and release the buttons.

When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, or Direct.

—

■ iPod/iPhone doesn’t work properly

Try reconnecting your iPod/iPhone.

■ How do I change the language of a multiplex

source

Recording

Use the “Input Ch (Mux)” setting on the “Audio

■ Can’t record

Adjust” menu to select “Main” or “Sub”.

On your recorder, make sure the correct input is

selected.

—

■ The ufunctions don’t work

To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., VCR/DVR IN to

VCR/DVR OUT).

To use u, you must make an uconnection and an

analog audio connection (RCA) between the

component and AV receiver, even if they are

connected digitally.

En-55

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded

correctly.

Before disconnecting the power cord from the wall

outlet, set the AV receiver to standby.

En-56

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Video Connection Formats

Audio Connection Formats

Connection Tips and

Video Signal Path

Video components can be connected by using any one of

the following video connection formats: composite video,

component video, or HDMI, the latter offering the best

picture quality.

Audio components can be connected by using any of the

following audio connection formats: analog, optical,

coaxial, or HDMI.

When choosing a connection format, bear in mind that the

AV receiver does not convert digital input signals for

analog line outputs and vice versa. For example, audio

signals connected to an optical or coaxial digital input are

not output by the analog VCR/DVR OUT.

The AV receiver supports several connection formats for

compatibility with a wide range of AV equipment. The

format you choose will depend on the formats supported by

your components. Use the following sections as a guide.

When choosing a connection format, bear in mind that the

AV receiver doesn’t convert between formats, so only

outputs of the same format as the input will output the

signal.

The on-screen menus appear only on a TV that is

connected to the HDMI OUT. If your TV is connected

to other video outputs, use the AV receiver’s display

when changing settings.

If signals are present at more than one input, the inputs will

be selected automatically in the following order of priority:

HDMI, digital, analog.

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Note

Audio Signal Flow Chart

• The on-screen setup menus are displayed when:

– There is no video input, or

– The video input is 480p, 576p, 720p, 1080i, or 1080p.

Composite

Component

HDMI

Blu-ray Disc/DVD player, etc.

AV receiver

Analog

Optical

Coaxial

HDMI

MONITOR OUT

Composite

Component

AV receiver

OUT

TV, projector, etc.

Analog

HDMI

*1 *2

TV, projector, etc.

Depends on the “Audio TV Out” setting (➔ page 43).

This is possible, when “Audio Return Ch” is set to “Auto”

(➔ page 44), the TV/CD input selector is selected, and your

TV is ARC capable.

Tip

• When a signal is input via HDMI and the corresponding input

selector is selected, the HDMI indicator lights.

En-57

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Operations that can be performed with

Using an RIHD-

compatible TV, Player,

or Recorder

p, which stands for Remote Interactive over

HDMI, is the name of the system control function found on

Onkyo components. The AV receiver can be used with

CEC (Consumer Electronics Control), which allows

system control over HDMI and is part of the HDMI

standard. CEC provides interoperability between various

components, however, operation with components other

than p-compatible components cannot be

guaranteed.

About p-compatible components

■ TV

• Toshiba TV

• Sharp TV

pconnection

The following components are p-compatible (As

■ For p-compatible TV

of January 2012).

The following linked operations are enabled by connecting

the AV receiver to an p-compatible TV.

• The AV receiver will enter standby mode when the TV is

set to standby.

■ Players/Recorders

• You can set on the menu screen of the TV to either output

the audio from the speakers connected to the AV

receiver, or from the speakers of the TV.

• Onkyo and Integra p-compatible players

• Toshiba players and recorders (only when used together

with Toshiba TV)

• It is possible to output the audio coming from the tuner or

auxiliary input of your TV to the speakers of the AV

receiver. (A connection such as an optical digital cable or

similar is required in addition to the HDMI cable.)

• Input to the AV receiver can be selected with the remote

controller of the TV.

• Operations such as volume adjustment or similar for the

AV receiver can be performed from the remote controller

of the TV.

• Sharp players and recorders (only when used together

with Sharp TV)

Models other than those mentioned above may have some

interoperability if compatible with CEC which is part of the

HDMI Standard, but operation cannot be guaranteed.

Note

■ For p-compatible players/recorders

The following linked operations are enabled by connecting

the AV receiver to an p-compatible

player/recorder.

• For proper linked operations, do not connect more p-

compatible components than the quantities specified below, to

the HDMI input terminal.

– Blu-ray Disc/DVD players: up to three.

– Blu-ray Disc/DVD recorders/Digital Video Recorders: up to

three.

• When the playback is started on the player/recorder, input

of the AV receiver will switch to the HDMI input of the

player/recorder that is playing back.

– Cable/Satellite Set-top boxes: up to four.

• Do not connect the AV receiver to the other AV receiver/AV

amplifier via HDMI.

• Proper linked operations are not guaranteed when more

p-compatible components than the above-mentioned

quantities are connected.

• Operation of the player/recorder is possible using the

remote controller supplied with the AV receiver.

Depending on the model used, not all operations may be

available.

To be continued

En-58

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

■ How to connect and setup

Change each item in the “HDMI Setup” menu

according to the following settings:

• HDMI Ctrl (RIHD): On

Operate with the remote controller.

For buttons that can be operated (➔ page 48).

Confirm the connecting and setting.

1. Connect the HDMI OUT jack to the HDMI input

Note

• Audio Return Ch (ARC): Auto

• Audio from DVD-Audio or Super Audio CD may not output

from the TV speakers. You will be able to output the audio

from the TV speakers by setting the audio output of the

DVD player to 2ch PCM. (It may not be possible depending

on the player models.)

• Even if you set to output audio on the TV speakers, audio

will be output from the speakers connected to the AV

receiver when you adjust the volume or switch the input on

the AV receiver. To output audio from the TV speakers, re-

do the operations on the TV.

jack of the TV.

Blu-ray Disc/DVD player, etc.

See details of each setting (➔ pages 43, 44).

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that the

power of the connected components is turned off

automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD

player/recorder.

4. Start playback on the Blu-ray Disc/DVD

player/recorder, and verify the following.

• The AV receiver automatically turns on, and

selects the input to which the Blu-ray

Disc/DVD player/recorder is connected.

• The TV automatically turns on, and selects the

input to which the AV receiver is connected.

5. Following the operating instructions of the TV,

select “Use the TV speakers” from the menu

screen of the TV, and confirm that the audio is

output from the speakers of the TV, and not from

the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV

receiver” from the menu screen of the TV, and

confirm that the audio is output from the speakers

connected to the AV receiver, and not from the

TV speakers.

HDMI

connection

AV receiver

• In case of an pconnection with uand uaudio

control compatible components, do not connect the u

cable at the same time.

DIGITAL AUDIO

connection

(OPTICAL)

HDMI

connection

• On the TV, when you select anything other than the HDMI

jack to which the AV receiver is connected, the input on the

AV receiver will be switched to “TV/CD”.

TV, projector, etc.

• The AV receiver will automatically power on in conjunction

when it determines it to be necessary. Even if the AV

receiver is connected to an pcompatible TV or

player/recorder, it will not power on if it is not necessary. It

may not power on in conjunction when the TV is set to

output audio from the TV.

• Linked functions with the AV receiver may not work

depending on the component model connected. In such

cases, operate the AV receiver directly.

2. Connect the audio output from the TV to the

OPTICAL IN 2 jack of the AV receiver using an

optical digital cable.

Note

• When the audio return channel (ARC) function is used with

an ARC capable TV, this connection is not necessary

(➔ page 44).

3. Connect the HDMI output of the Blu-ray

Disc/DVD player/recorder to the HDMI IN 1 jack

of the AV receiver.

Note

• It is necessary to assign the HDMI input when connecting

the Blu-ray Disc/DVD player/recorder to other jacks

(➔ page 37). Do not assign an HMDI IN to the TV/CD

selector at this time, otherwise appropriate CEC (Consumer

Electronics Control) operation will not be guaranteed.

Note

• Perform the above operations when you use the AV receiver

for the first time, when the settings of each component are

changed, when the main power of each component is turned

off, when the power cable is disconnected from the power

supply, or when there has been a power outage.

En-59

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Supported Audio Formats

About Copyright Protection

About HDMI

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,

16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,

Dolby TrueHD, DTS, DTS-HD High Resolution Audio,

DTS-HD Master Audio)

The AV receiver supports HDCP (High-bandwidth Digital

Designed to meet the increased demands of digital TV,

HDMI (High Definition Multimedia Interface) is a new

digital interface standard for connecting TVs, projectors,

Blu-ray Disc/DVD players, set-top boxes, and other video

components. Until now, several separate video and audio

cables have been required to connect AV components.

With HDMI, a single cable can carry control signals,

digital video, and up to eight channels of digital audio (2-

channel PCM, multichannel digital audio, and

Content Protection) , a copy-protection system for digital

video signals. Other devices connected to the AV receiver

via HDMI must also support HDCP.

DVI (Digital Visual Interface): The digital display interface

Your Blu-ray Disc/DVD player must also support HDMI

output of the above audio formats.

standard set by the DDWG in 1999.

HDCP (High-bandwidth Digital Content Protection): The

video encryption technology developed by Intel for

HDMI/DVI. It’s designed to protect video content and requires

a HDCP-compatible device to display the encrypted video.

multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible

with DVI (Digital Visual Interface) , so TVs and displays

with a DVI input can be connected by using an HDMI-to-

DVI adapter cable. (This may not work with some TVs and

displays, resulting in no picture.)

DDWG (Digital Display Working Group): Lead by Intel,

Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon

Image, this open industry group’s objective is to address the

industry’s requirements for a digital connectivity specification

for high-performance PCs and digital displays.

The AV receiver uses HDCP (High-bandwidth Digital

Content Protection) , so only HDCP-compatible

components can display the picture.

Note

• The HDMI video stream is compatible with DVI (Digital Visual

Interface), so TVs and displays with a DVI input can be

connected by using an HDMI-to-DVI adapter cable. (Note that

DVI connections only carry video, so you’ll need to make a

separate connection for audio.) However, reliable operation with

such an adapter is not guaranteed. In addition, video signals from

a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be

restricted by the connected source component. If the picture is

poor or there’s no sound from a component connected via HDMI,

check its setup. Refer to the connected component’s instruction

manual for details.

The AV receiver’s HDMI interface is based on the

following:

Audio Return Channel, 3D, x.v.Color, DeepColor, Lip

Sync, DTS-HD Master Audio, DTS-HD High

Resolution Audio, Dolby TrueHD, Dolby Digital Plus,

DSD and Multichannel PCM.

En-60

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Supported Audio File Formats

USB Features

For playback from a USB device, the AV receiver supports

the following music file formats.

USB Device Requirements

Variable bit-rate (VBR) files are supported. However,

playback time may not be display correctly.

• USB mass storage device class (but not always

guaranteed).

• FAT16 or FAT32 file system format.

• Up to 255 folders can be displayed, and folders may be

nested up to 8 levels deep.

• USB hubs and USB devices with hub functions are not

supported.

■ MP3 (.mp3 or .MP3)

• MP3 files must be MPEG-1/MPEG-2.5 Audio Layer 3

format with a sampling rates of 8 kHz, 11.025 kHz,

12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,

48 kHz and bitrates of between 8 kbps and 320 kbps.

Incompatible files cannot be played.

Note

■ WMA (.wma or .WMA)

• If the media you connect is not supported, the message “No

Storage” will be displayed.

WMA stands for Windows Media Audio and is an audio

compression technology developed by Microsoft

Corporation. Audio can be encoded in WMA format by

• If you connect a USB hard disk drive to the AV receiver’s USB

port, we recommend that you use its AC adapter to power it.

• The AV receiver supports USB MP3 players that support the

USB Mass Storage Class standard, which allows USB devices to

be connected to computers without the need for special drivers or

software. Note that not all USB MP3 players support the USB

Mass Storage Class standard. Refer to your USB MP3 player’s

instruction manual for details.

using Windows Media Player.

• WMA files must have the copyright option turned off.

• Sampling rates of 32 kHz, 44.1 kHz, 48 kHz, bitrates of

between 48 kbps and 320 kbps are supported.

• WMA DRM/Pro/Voice formats are not supported.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or

damage to data stored on a USB device when that device is used

with the AV receiver. We recommend that you back up your

important music files beforehand.

■ AAC (.aac/.m4a/.mp4/.AAC/.M4A or .MP4)

AAC stands for MPEG-2/MPEG-4 Audio.

• Sampling rates of 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,

44.1 kHz, 48 kHz and bitrates of between 8 kbps and

320 kbps are supported.

• MP3 players containing music files that are managed with special

music software are not supported.

• Operation is not guaranteed for all USB devices, which includes

the ability to power them.

• Do not connect your USB device via a USB hub. The USB device

must be connected directly to the AV receiver’s USB port.

• If the USB device contains a lot of data, the AV receiver may take

a while to read it.

■ FLAC (.flac or .FLAC)

FLAC is a file format for lossless audio data compression.

• Sampling rates of 32 kHz, 44.1 kHz and 48 kHz are

supported.

• Quantization bit: 16 bit, 24 bit

• USB devices with security functions cannot be played.

En-61

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

License and Trademark

Information

“x.v.Color” is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent Nos: 5,956,674;

5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;

7,392,195; 7,272,567 & other U.S. and worldwide patents issued

& pending. DTS-HD, the Symbol, & DTS-HD and the Symbol

together are registered trademarks of DTS, Inc. Product includes

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories.

Music Optimizer™ is a trademark of Onkyo Corporation.

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.”

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and

iPod touch are trademarks of Apple Inc., registered in the U.S.

and other countries.

“Made for iPod” and “Made for iPhone” mean that an electronic

accessory has been designed to connect specifically to iPod or

iPhone, respectively, and has been certified by the developer to

meet Apple performance standards. Apple is not responsible for

the operation of this device or its compliance with safety and

regulatory standards.

Please note that the use of this accessory with iPod or iPhone

may affect wireless performance.

En-62

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

■ HDMI

Video Section

Specifications

Amplifier Section

Input

Output

Video Resolution

Audio Format

IN 1, IN 2, IN 3, IN 4

Input Sensitivity/Output Level and Impedance

OUT

1 Vp-p/75 Ω (Component Y)

1080p

0.7 Vp-p/75 Ω (Component P^B/CB, PR/CR)

Dolby TrueHD, DTS-HD Master Audio,

DVD-Audio, DSD

1 Vp-p/75 Ω (Composite)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, –3 dB

Rated Output Power

All channels:

60 watts minimum continuous power per

Supported

3D, Audio Return Channel, DeepColor,

x.v.Color, LipSync, CEC (RIHD)

channel, 8 ohm loads, 2 channels driven

from 20 Hz to 20 kHz, with a maximum

total harmonic distortion of 0.7% (FTC)

90 watts minimum continuous power per

channel, 6 ohm loads, 2 channels driven at

1 kHz, with a maximum total harmonic

distortion of 0.9% (FTC)

Tuner Section

■ Video Inputs

Component

Composite

IN 1, IN 2

FM Tuning Frequency Range

87.5 MHz - 107.9 MHz

AM Tuning Frequency Range

530 kHz - 1710 kHz

BD/DVD, VCR/DVR, CBL/SAT, GAME,

AUX

Dynamic Power

IEC60268-Short-term maximum output power

160 W (3 Ω, Front)

125 W (4 Ω, Front)

85 W (8 Ω, Front)

■ Video Outputs

Preset Channel

Component

Composite

OUT

THD+N (Total Harmonic Distortion+Noise)

General

MONITOR OUT, VCR/DVR OUT

0.08% (20 Hz - 20 kHz, half power)

Damping Factor

Input Sensitivity and Impedance (Unbalance)

200 mV/47 kΩ (LINE)

60 (Front, 1 kHz, 8 Ω)

■ Audio Inputs

Digital

Power Supply

AC 120 V, 60 Hz

Power Consumption 3.4 A

No-sound Power Consumption

40 W

Optical: 2

Coaxial: 1

Rated RCA Output Level and Impedance

200 mV/2.2 kΩ (REC OUT)

Analog

BD/DVD, VCR/DVR, CBL/SAT, GAME,

TV/CD, AUX

Maximum RCA Output Level and Impedance

2 V/2.2 kΩ (REC OUT)

Stand-by Power Consumption

0.2 W

■ Audio Outputs

Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (DSP bypass)

Dimensions (W × H × D)

Tone Control Characteristics

435 mm × 150 mm × 318 mm

17-1/8" × 5-7/8" × 12-1/2"

Analog

VCR/DVR

10 dB, 50 Hz (BASS)

10 dB, 20 kHz (TREBLE)

Subwoofer Pre Output 1

Speaker Outputs

Phones

Weight

7.6 kg (16.8 lbs.)

SP-A (L, R, C, SL, SR) + SP-B (L, R)

1 (6.3 ø)

Signal to Noise Ratio 100 dB (LINE, IHF-A)

Speaker Impedance

6 Ω - 16 Ω

■ Others

USB

1 (Front)

Specifications and features are subject to change

without notice.

En-63

Download from Www.Somanuals.com. All Manuals Search And Download.

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163

http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650

http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4208-213

http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.

Tel: 852-2429-3118 Fax: 852-2428-9039

http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,

China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396

http://www.cn.onkyo.com/

Y1201-1

SN 29401114

* 2 9 4 0 1 1 1 4 *

Download from Www.Somanuals.com. All Manuals Search And Download.

Miele Cooktop H370 2 User Manual
MTD Tiller 215 100AB2 User Manual
Nikon Digital Camera 26462 User Manual
Niles Audio Home Theater System CM6HDFX User Manual
Nilfisk Advance America Vacuum Cleaner AERO 20 User Manual
NordicTrack Treadmill CTL49021 User Manual
N Tron Switch 1003GX2 User Manual
Omnimount TV Mount OL50FT User Manual
Palsonic Flat Panel Television 5110PF User Manual
Paradigm Speaker System IN WALL SUBWOOFERS User Manual