Getting Started..........................2
CD Receiver
CR-515
CR-315
Connections ............................16
Basic Operation ......................27
Playing a Disc..........................30
Listening to the Radio ........... 39
Instruction Manual
Thank you for purchasing an Onkyo CD Receiver.
Please read this manual thoroughly before making
any connections and plugging it in.
Miscellaneous .........................54
Troubleshooting................................ 54
If you can’t resolve an issue, try reset-
ting the CD receiver by holding down
the [ ] button and pressing the
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new CD Receiver.
Please retain this manual for future reference.
[STANDBY/ON] button.
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
• Avoid damp and dusty places, and places subject
to vibrations from loudspeakers. Never put the
unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its
side or on a sloping surface, because it may cause
a malfunction.
2. AC Fuse—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
• If you install this unit near a TV, radio, or VCR,
the picture and sound quality may be affected. If
this occurs, move this unit away from the TV,
radio, or VCR.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a
clean cloth. Don’t use abrasive cloths, thinners, alco-
hol, or other chemical solvents, because they may
damage the finish or remove the panel lettering.
8. To Obtain a Clear Picture—This unit is a high-
tech, precision device. If the lens on the optical
pickup, or the disc drive mechanism becomes dirty
or worn, the picture quality may be affected. To
maintain the best picture quality, we recommend
regular inspection and maintenance (cleaning or
worn part replacement) every 1,000 hours of use
depending on the operating environment. Contact
your Onkyo dealer for details.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
9. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
Moisture may condense on the lens of the optical
pickup, one of the most important parts inside this
unit.
• Moisture condensation can occur in the following
situations:
– The unit is moved from a cold place to a warm
place.
Pressing the [STANDBY/ON] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
5. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
– In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so
may damage your discs and certain parts inside
this unit.
If condensation does occur, remove all discs and
leave this unit turned on for two to three hours. By
this time, the unit will have warmed up and any con-
densation will have evaporated.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For European Models
Declaration of Conformity
• When you’ve finished using this unit, remove all
discs and turn off the power.
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
7. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an
audio rack. If the ventilation is inadequate, the
unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may
rise, shortening the life of the optical pickup.
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Precautions—Continued
Make sure you have the following accessories:
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit.
To prevent being exposed to the laser beam, do not try to
open the enclosure.
Remote controller and two batteries (AA/R6)
DANGER:
VISIBLE AND/OR INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK FAILED OR
DEFEATED. DO NOT STARE INTO BEAM.
Indoor FM antenna
(Connector type varies from country to country.)
CAUTION:
THIS PRODUCT UTILIZES A LASER. USE OF CON-
TROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECI-
FIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
AM loop antenna
The label on the right is
applied on the rear panel.
1. This unit is a CLASS 1
LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
Power cord
(Plug type varies from country to country.)
* In catalogs and on packaging, the letter at the end of the product
name indicates the color. Specifications and operations are the
same regardless of color.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue:
Neutral
Brown: Live
As the colours of the wires in the mains lead of this appa-
ratus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as fol-
lows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for the
ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable fuse
in the plug.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using the CD Receiver
Installing the Batteries
Using the Remote Controller
When you operate the remote controller, point it at the
CD receiver’s remote control sensor, as shown below.
Detach the battery cover by pressing the
tab and pulling up the cover.
1
Remote control sensor
CD receiver
Insert two AA-size batteries into the bat-
tery compartment.
2
Carefully follow the polarity diagram (positive
(+) and negative (–) symbols) inside the battery
compartment.
Notes:
• The remote controller may not work reliably if the CD
receiver is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
• If another remote controller of the same type is used in
the same room, or the CD receiver is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
• Don’t put anything, such as a book, on the remote con-
troller because the buttons may be pressed inadvert-
ently, thereby draining the batteries.
• The remote controller may not work reliably if the CD
receiver is installed in a rack behind colored glass
doors. Keep this in mind when installing.
• The remote controller will not work if there’s an obsta-
cle between it and the CD receiver’s remote control
sensor.
After the batteries are installed and
seated correctly, attach the compartment
cover.
3
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as possi-
ble to prevent damage from leakage or corrosion.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Amplifier
• WRAT (Wide Range Amplifier Technology)
• High Current, Low Impedance Drive
• Discrete Output Stage Circuitry
• Optimum Gain Volume Circuitry
• Subwoofer Pre Out
— CR-515 —
• VLSC (Vector Linear Shaping Circuitry)*
• 4 Audio Inputs and 2 Outputs (1 on front panel)
— CR-315 —
• 3 Audio Inputs (1 on front panel) and 1 Output
CD Player
• Plays CDs, MP3 CDs, CD-Rs and CD-RWs
• 25 Track Programming
• 2 Repeat Mode (Track/Full)
• 4 Play Modes (Normal/Random/Memory/1 Folder)
— CR-515 —
• Wolfson Multi-Bit
— CR-315 —
• Single-Bit D/A Converter
Tuner & Other
• 4-Program Timer (Play or Rec / Once or Every)
• Sleep Timer
• Battery-Free Memory Backup
• Headphone Jack
• Aluminium Front Panel
• RI-Dock Compatible Remote Control (iPod Control
Capable)
* VLSC and the VLSC logo are registered trademarks of Onkyo
Corporation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting to Know the CD Receiver ......................8
Front Panel .....................................................8
Display .........................................................10
Rear Panel ...................................................11
About the Timers ..........................................49
Programming the Timers ..............................50
Turning Timers On and Off ...........................52
Checking Timer Settings ..............................52
Specifications ...................................................57
Connecting Antennas .......................................16
Connecting Speakers .......................................18
Connecting the Power Cord .............................25
First Time Setup (European Model Only) ........26
Connecting Other Components ........................19
Cables and Jacks .........................................19
Connecting an Onkyo MD recorder ..............21
Using Headphones .......................................27
Adjusting the Bass and Treble .....................28
Using the Super Bass Function ....................28
Using the Direct Function .............................28
Connecting an Onkyo CD Recorder
(CR-515) ....................................................23
Connecting a Portable Audio Device.............23
Playing a Disc
Playing CDs .....................................................30
Using the Remote Controller ........................31
Displaying CD Information ...........................31
Memory Playback .........................................35
Random Playback ........................................36
Repeat Playback ..........................................36
Setting MP3 Preferences ..............................37
Presetting FM Stations Automatically
(Auto Preset) .............................................40
Presetting AM/FM Stations Manually ...........41
Selecting Preset Stations .............................42
Displaying Radio Information .......................43
Receiving RDS .............................................43
Naming Presets ............................................44
Copying Presets ...........................................45
Erasing a Preset’s Name ..............................46
Erasing Presets ............................................46
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The page numbers in parentheses show where you can find the main explanation for each item.
A STANDBY indicator (25, 27)
P LINE IN jack (CR-315) (23)
This stereo minijack is for connecting an audio
source, such as an MP3 music player or personal
computer.
Lights up in Standby mode.
B STANDBY/ON button (27, 48, 51, 54)
Sets the CD receiver to On or Standby.
Used to change the information shown on the dis-
play. Also used to select characters when naming
radio presets.
C Remote control sensor (5)
Receives control signals from the remote controller.
D Display
See “Display” on page 10.
R Previous and Next [
]/[
] buttons
E VOLUME control (27)
(CR-315) (30)
Adjusts the volume level.
On the CR-515, the volume control indicator lights
up when the CD receiver is on.
The Previous [
] button selects the previous
track. During playback it selects the beginning of
the current track. The Next [
next track.
] button selects the
F PHONES jack (27)
This stereo minijack is for connecting a pair of ste-
reo headphones for private listening.
G LINE 2 IN jack (CR-515) (23)
source, such as an MP3 music player or personal
computer.
H Disc tray (30)
The CD is loaded here.
I INPUT button (27, 29, 40, 42)
Used to select the input source.
J DIRECT button (28)
Used with the Direct function.
On the CR-515, the DIRECT button’s indicator
lights up when the Direct function is on.
K TONE button (CR-515) (28)
L Multi control (CR-515) (30, 42)
ers. Also used to select and set various functions and
settings.
M Eject [ ] button (30)
Ejects the loaded CD.
N Stop [ ] button (30, 54)
Stops CD playback.
O Play/Pause [
] button (30)
/
Starts CD playback. Pressing it during playback
pauses playback.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the CD Receiver—Continued
Display
1
2
3 4 5 6
7
8
9
J
K
L M
N
O P
1, 2, 3, 4: Light up when a timer has been pro-
A SLEEP indicator
grammed.
Lights up when the Sleep function has been set.
B MP3 indicator
: Lights up when a timer has been programmed
for recording.
Lights up when an MP3 CD is loaded.
C PCM indicator
K Tuning indicators
Lights up when the digital input signal received by
the DIGITAL IN jack is PCM. It flashes if the signal
is not PCM or the CD receiver is not locked to the
incoming digital signal.
AUTO: Lights up when Auto Tuning is selected,
and disappears when Manual Tuning is selected.
: Lights up when the CD receiver is tuned
to a radio station.
D FOLDER indicator
Lights up while the number of an MP3 folder is
being displayed.
FM ST: Lights up when the CD receiver is tuned to
a stereo FM station.
E DIRECT indicator
RDS (European model only): Lights up when
the CD receiver is tuned to a radio station that sup-
ports RDS (Radio Data System).
Lights up when the Direct function is on.
F S.BASS indicator
Lights up when the Super Bass function is on.
L FILE indicator
G MUTING indicator
Lights up when an MP3 file number is being dis-
played.
Flashes while the CD receiver is muted.
H Playback mode indicators
M TRACK indicator
Lights up when a CD track number is being dis-
played.
1FOLDER: Lights up when 1-folder playback is
selected.
N TITLE, ARTIST and ALBUM indicators
TITLE lights up when the title (ID3 tag) of an MP3
track is being displayed.
MEMORY: Lights up when memory playback is
selected.
RANDOM: Lights up when random playback is
selected.
ARTIST lights up when the artist name from an
MP3 track (ID3 tag) is being displayed.
ALBUM lights up when the album name from an
MP3 track (ID3 tag) is being displayed.
REPEAT: Lights up when repeat playback is
selected for all tracks.
O DISC,TOTAL, and REMAIN indicators
These indicators light up when the total time or the
remaining disc or track time is being displayed.
REPEAT 1: Lights up when repeat playback is
selected for one track.
I Play and pause
indicators
/
P Message area
The Play indicator lights up for playback. The Pause
indicator lights up while playback is paused.
Various information is displayed here, including
radio preset numbers, tuning frequency, current
time, volume level, sleep time, mode settings, and
so on.
J TIMER indicators
Show the status of the timers.
TIMER: Lights up when a timer has been pro-
grammed.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know the CD Receiver—Continued
Rear Panel
CR-515
1 2 3 4
5
6
7
LINE 1
IN
OUT
MD/
TAPE
IN
OUT
DOCK/
CDR
IN
R
L
AC INLET
8 9
J
CR-315
DOCK
IN
K
OUT
The page numbers in parentheses show where you can find the main explanation for each item.
A LINE 1 IN (CR-515) (25)
H
REMOTE CONTROL (20–24)
This analog audio input is for connecting a compo-
nent with an analog output, such as a TV, or a turn-
table with a built-in phono equalizer.
This
(Remote Interactive) jack can be con-
nected to an
The CD receiver’s remote controller can then be
jack on another Onkyo component.
B MD/TAPE IN/OUT (20, 21)
These analog audio inputs and outputs are for con-
necting a recorder with an analog input and output,
such as a MiniDisc recorder or cassette deck.
must make an analog audio connection (RCA)
between the CD receiver and the other component,
even if they are connected digitally.
C DOCK/CDR IN/OUT (CR-515) (22, 23)
These analog audio inputs and outputs are for con-
necting a recorder with an analog input and output
such as a CD recorder, or an Onkyo RI Dock.
I OPTICAL DIGITAL IN (CR-515 Asian model
only) (24)
This optical digital audio input can be used to con-
such as a CD recorder, MD recorder, games con-
commercially available optical digital audio cable to
make the connection.
D AM ANTENNA (16, 17)
These push terminals are for connecting an AM
antenna.
E FM ANTENNA (16, 17)
J AC INLET (25)
This jack is for connecting an FM antenna.
The supplied power cord is connected here.
F SUBWOOFER PRE OUT (19)
This analog audio input is for connecting an Onkyo
RI Dock.
This jack is for connecting a powered subwoofer.
G SPEAKERS (18)
These terminal posts are for connecting speakers.
The North American CR-315 has push-type termi-
nals.
See pages 16–25 for connection information.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The page numbers in parentheses show where you can find the main explanation for each item.
A STANDBY/ON button (27, 51)
Standby.
L Onkyo MD recorder and cassette deck
control buttons
For twin cassette decks, only Deck B can be con-
trolled.
B SLEEP button (53)
: Plays side B (cassette deck).
Used to set the Sleep timer, which turns off the CD
receiver after a specified time.
: Pauses playback or recording (MD).
: Stops playback, recording, fast-forward, or
rewind.
Used to select tracks and radio presets. Also used to
set the clock manually, set the timers, and enter
Onkyo RI Dock or CD recorder.
: Plays side A.
M CLOCK CALL button (48)
Calls up the clock to display the day and time.
D TIMER button (26, 47, 48, 50, 52)
N INPUT [ ]/[ ] buttons (27, 29, 40, 42)
Used to set the timers and clock.
Used to select the input source.
E MENU/NO/CLEAR button (29, 37, 40, 41,
44–46)
O DISPLAY button (31, 34, 43, 44, 48)
play. Also used to select characters when naming
recorder. With an Onkyo RI Dock, it works as a
backlight button.
Used with various functions and settings for select-
ing, cancelling, and deleting. With an Onkyo CD
recorder, it works as a clear button. With an Onkyo
RI Dock, it works as a mode button.
F Previous/Next [
]/[
] and
P FOLDER button (32, 33, 34, 38)
[
PRESET]/[PRESET ] buttons (31, 42)
Used to select MP3 folders.
Used to select the previous or next track or radio
preset. Can also be used with an Onkyo RI Dock or
CD recorder. With an Onkyo cassette deck, they
work as rewind and fast forward buttons.
Q REPEAT button (36)
Onkyo RI Dock or CD recorder. With an Onkyo
cassette deck, it works as a reverse mode button.
G Rewind/Fast Forward [ ]/[ ] and
R TONE button (28)
[
Used to adjust the bass and treble.
Used to rewind or fast forward CD playback. Can
also be used with an Onkyo RI Dock or CD
recorder. Also used to tune the radio and edit preset
names.
S YES/MODE/SHUFFLE button (34–36, , 39)
Used with various functions and settings for con-
firming, selecting modes, and selecting shuffle play-
back.
H CD control buttons (31)
: Pauses playback.
T ENTER button
Used to confirm various functions and settings. Can
also be used with an Onkyo RI Dock or CD
recorder.
: Stops playback.
: Starts playback.
I VOLUME [ / ] buttons (27, 31)
Adjust the volume level.
U MUTING button (28)
Mutes the output of the CD receiver.
J S.BASS button (28)
V TUNER/BAND button (39, 40, 42)
Sets the Super Bass function.
Selects AM or FM radio as the input source.
K Onkyo RI Dock and CD recorder control
buttons
: Pauses playback or recording.
: Stops playback or recording.
: Starts playback or resumes recording.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Notes
Supported Discs
Discs Made on Personal Computers
The CD receiver supports the following discs.
Discs made on personal computers, including those of a
compatible format, may not work properly in the CD
receiver because of incorrect settings in the disc burning
software. Check the manuals supplied with your disc
burning software for additional compatibility informa-
tion.
Disc
Logo
Format or file type
Audio CD
PCM
Audio CD, MP3
MP3
MP3 Compatibility
CD-R
• MP3 discs must be ISO 9660 Level 1 or Level 2,
Romeo or Joliet compliant. Supported formats:
Mode 1, Mode 2 XA Form 1.
Audio CD, MP3
MP3
• Folders can be up to eight levels deep.
• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with a sampling rate of between 8 kHz and
48 kHz and a bit-rate of between 8 kbps and 320 kbps
(128 kbps recommended). Incompatible files cannot
be played.
• Constant bit rate MP3 files are recommended, how-
ever, variable bit-rate (VBR) MP3 files between
8 kbps and 320 kbps are supported. (Playing times
may not display correctly.)
• MP3 files must have a “.mp3” or “.MP3” file name
extension. MP3 files without the proper extension will
not be recognized. To prevent noise and malfunction,
do not use these extensions for other types of files.
• The CD receiver supports up to 499 MP3 files and
folders. Files and folders in excess of this cannot be
played. Note that if the file and folder structure is very
complicated, the CD receiver may not be able to read
or play all of the MP3 files on the disc.
CD-RW
Audio CD (Session 1),
MP3 (Session 2)
CD Extra
• Some audio CDs use copy protection that doesn’t con-
form to the official CD standard. Since these are non-
standard discs, they may not play properly in the CD
receiver.
• The CD receiver supports CD-R and CD-RW discs.
However, some CD-R and CD-RW discs may not
work properly for any of the following reasons: disc
burner characteristics, disc characteristics, the disc is
damaged or dirty. See the manual supplied with your
disc burner for more information. Condensation or dirt
on the optical pickup lens can also affect playback.
• The CD receiver supports 8 cm and 12 cm discs.
• The CD receiver does not support disc types not listed.
• Don’t use discs with an unusual shape, such as those
shown below, as you may damage the CD receiver.
• Disc, file, and folder names may contain up to 32 char-
acters.
• The maximum time that can be displayed for a single
file is 99 minutes and 59 seconds.
• The remaining time cannot be displayed when playing
MP3 files.
• MP3 file and folder names (excluding the extension)
are shown on the display.
• Multisession discs are supported, however, some mul-
tisession discs may take a long time to load and some
may not load at all. When burning CDs, we recom-
mend that you use a single-session (disc-at-once), and
select “Disc Close.”
disc is played. However, you can set the CD receiver
so that it plays any MP3 files in the data session of a
CD-R/RW disc instead. If the data session contains no
MP3 files, the audio session will be played regardless.
See “Setting MP3 Preferences” on page 37 for more
information.
• Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custom-
made labels or stickers. Doing so may damage the CD
receiver and you may not be able to remove the disc
properly.
• The Emphasis is not supported.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Notes—Continued
• The following ID3 tags are supported: versions 1.0/1.1
and 2.2/2.3/2.4. Versions 2.5 and later are not sup-
ported. Normally, version 2.2/2.3/2.4 tags have prior-
ity and will be displayed regardless of the ID3 VER 1
preference on page 37.
Handling Discs
• Never touch the underside of a disc.Always hold discs
by the edge, as shown.
• For ID3 version 2 tags, the tag information recognized
will be those embedded in the beginning of the file. We
recommend that you include only title, artist name,
and album name information in ID3 tags. Com-
pressed, encrypted, and unsynchronized ID3 tags can-
not be displayed.
Underside
• Never attach adhesive tape or sticky labels to discs.
Note:
With CD-ROM, CD-R, and CD-RW discs that contain
many files and folders and files other than MP3s, it may
take a long time to read the disc. We recommend that you
include only MP3 files on your discs, use about 20 fold-
ers, and limit folder nesting to three levels deep.
Cleaning Discs
Disc Content Organization
• For best results, keep your discs clean. Fingerprints
and dust can affect the sound quality and should be
removed as follows. Using a clean soft cloth, wipe
from the center outwards, as shown. Never wipe in a
circular direction.
■ CD
CDs contain tracks.
Track 1
Track 2
Track 3
Track 4
Track 5
Audio CD
✔
■ MP3
MP3 discs contain MP3 files organized into folders.
• To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thin-
ner or benzine, commercially available cleaners, or
antistatic sprays intended for vinyl records, as they
may damage the disc.
Folder 1
File 2
Folder 2
File 1 File 2
File 1
File 3
MP3 (CD-R/CD-RW)
Storing Discs
• Don’t store discs in places subject to direct sunlight or
near heat sources.
• Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stack-
ing, or putting objects on unprotected discs may cause
warping, scratches, or other damage.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas
This section explains how to connect the supplied indoor
FM antenna and AM loop antenna, and how to connect
commercially available outdoor FM and AM antennas.
The CD receiver won’t pick up any radio signals without
an antenna connected, so you must connect the antenna
to use the tuner.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use
only.
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
1
AM antenna push terminals
FM antenna jack
LINE
IN
1
OUT
MD/
TAPE
IN
OUT
DOCK/
CDR
IN
R
L
AC INLET
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
2
Connecting the Indoor FM Antenna
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
■ North American Model
1
Insert the plug fully
into the jack.
Push
Insert wire
Release
■ Other Models
Insert the plug fully
into the jack.
Once the CD receiver is ready for use, you’ll need
to tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from the
CD receiver, TV, speaker cables, and power cords.
Once the CD receiver is ready for use, you’ll need
to tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
Use thumbtacks or something similar to
fix the FM antenna into position.
2
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna (see page 17).
Thumbtacks, etc.
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead (see page 17).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Antennas—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoorAM antenna can be used in
addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
OutdoorAM antennas work best when installed horizon-
tally outside, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
• For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage
equipment.
• Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
■ Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To CD receiver
To TV (or VCR)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Speakers
ConnectingYour Speakers
• Connect the right speaker to the CD receiver’s right (R) SPEAKERS terminals. Connect the left speaker to the left
(L) SPEAKERS terminals.
• Connect the positive (+) terminal on each speaker to the corresponding positive (+) terminal on the CD receiver.
Connect the negative (–) terminal on each speaker to the corresponding negative (–) terminal on the CD receiver. Use
the red wires to connect the positive (+) terminals.
Left speaker
Right speaker
—Terminal posts—
Strip about 15 mm (5/8") of insulation from the ends of the speaker
cables, and twist the bare wires tightly. Unscrew the terminal. Fully
insert the bare wire, making sure that it’s touching the threaded shaft in
the center. Screw the terminal tight.
Red wires
Speaker
cable
R
L
—Push-type terminals—
Strip about 10 mm (3/8") of insulation from the ends of the speaker
cables, and twist the bare wires tightly. Push the lever and insert the
bare wires. Release the lever. Make sure the terminal is gripping the
bare wires and not the insulation.
SPEAKERS
OUT
DOCK/
CDR
IN
R
L
AC INLET
• Connect only speakers with an impedance of between
4 and 16 ohms. Connecting a speaker with a lower
impedance may damage the speaker.
• Do not connect both speaker cables to the same L or R
terminals (Fig. 1). Do not connect more than two
speaker terminals to each speaker (Fig. 2).
• Be careful not to short the positive and negative wires.
Doing so may damage the CD receiver.
Fig. 1
Fig. 2
R
L
R
L
SPEAKERS
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components
About Connections
• Before making any connections, read the manuals
supplied with your other components.
• Don’t connect the power cord until you’ve completed
and double-checked all connections.
• Push plugs in all the way to make
Right!
good connections (loose connec-
tions can cause noise or malfunc-
tions).
• To prevent interference, keep
audio cables away from power
cords and speaker cables.
Wrong!
Connection Color Coding
RCA-type audio connections are usually color-coded:
red and white. Use red plugs to connect right-channel
audio inputs and outputs (typically labeled “R”). Use
white plugs to connect left-channel audio inputs and out-
puts (typically labeled “L”).
Optical Digital Jack (CR-515)
The CD receiver’s optical digital jack has a shutter-type
cover that opens when an optical plug is inserted and
closes when it’s removed. Push the plug in all the way.
Analogaudio
Left (white)
Right (red)
Left (white)
Right (red)
cable
Caution: To prevent shutter damage, hold the optical
plug straight when inserting and removing.
Note:
Do not put anything on top of the CD receiver, as it may
interfere with proper ventilation.
Cables and Jacks
No connecting cables are included with the CD receiver.
Cable
Jack
Description
R
L
This cable carries analog audio.
Analog audio
cable (RCA)
OPTICAL
This cable carries digital audio.
This cable carries analog audio.
Optical digital
audio cable
Stereo miniplug
cable
Connecting a Subwoofer
The CD receiver has a SUBWOOFER PRE OUT jack for connecting a powered subwoofer (i.e., a subwoofer with a
built-in amplifier).
CD receiver
Powered subwoofer
LINE
IN
1
OUT
MD/
TAPE
IN
OUT
DOCK/
CDR
IN
R
L
SUB
WOOFER
AC INLET
PRE OUT
: Signal flow
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting an Onkyo Cassette Deck
The following diagram shows how to connect an optional Onkyo cassette deck.
Connect the CD receiver’s MD/TAPE OUT jacks to the cassette deck’s INPUT (REC) jacks, and connect the CD
receiver’s MD/TAPE IN jacks to the cassette deck’s OUTPUT (PLAY) jacks.
CR-515’s
rear panel
Onkyo cassette deck’s
rear panel
LINE 1
INPUT OUTPUT
Red
IN
REMOTE
CONTROL
(REC)
(PLAY)
L
OUT
White
White
MD/
TAPE
Analog audio cables (RCA)
R
IN
OUT
Red
DOCK/
CDR
IN
White
Red Red White
R
L
cable supplied with
the Onkyo cassette deck
CR-315’s
rear panel
Onkyo cassette deck’s
rear panel
DOCK
INPUT OUTPUT
Red
IN
REMOTE
(REC)
(PLAY)
CONTROL
L
OUT
White
White
MD/
TAPE
Analog audio cables (RCA)
R
IN
R
L
Red
White Red Red White
cable supplied with
the Onkyo cassette deck
: Signal flow
What can you do with
?
cable allows you to control the cassette deck with
the CD receiver’s remote controller. In addition, when playback is started on the cassette deck, the CD receiver will
automatically select it as the input source.
• To use
, you must connect the Onkyo cassette deck to the CD receiver with an
cable and an analog audio cable
(RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “TAPE.” Since this is the default setting,
unless you’ve changed it, it can be left as it is (see page 29).
• Some
-capable components have two
jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional
-capable components.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting an Onkyo MD recorder
The following diagram shows how to connect an optional Onkyo MD recorder.
Connect the CD receiver’s MD/TAPE OUT jacks to the MD recorder’s INPUT (REC) jacks, and connect the CD
receiver’s MD/TAPE IN jacks to the MD recorder’s OUTPUT (PLAY) jacks.
CR-515’s
Onkyo MD recorder’s
rear panel
rear panel
LINE 1
INPUT OUTPUT
Red
IN
REMOTE
(REC)
(PLAY)
CONTROL
L
OUT
White
White
MD/
TAPE
Analog audio cables (RCA)
R
IN
OUT
Red
DOCK/
CDR
IN
White
Red Red White
R
L
cable supplied with
the Onkyo MD recorder
CR-315’s
rear panel
Onkyo MD recorder’s
rear panel
DOCK
INPUT OUTPUT
Red
IN
REMOTE
(REC)
(PLAY)
CONTROL
L
OUT
White
White
MD/
TAPE
Analog audio cables (RCA)
R
IN
R
L
Red
White Red Red White
cable supplied with
the Onkyo MD recorder
: Signal flow
What can you do with
?
• Connecting an Onkyo MD recorder to the CD receiver with an
cable allows you to control the MD recorder with
the CD receiver’s remote controller. In addition, when playback is started on the MD recorder, the CD receiver will
automatically select it as the input source.
• To use
(RCA). In addition, the Input Display for the MD/TAPE jacks must be set to “MD” (see page 29).
• Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
, you must connect the Onkyo MD recorder to the CD receiver with an
cable and an analog audio cable
Note:
• The MD/TAPE jacks can alternatively be used to connect a VCR or DAT recorder, in which case the Input Display
on the CD receiver would need to be set to “VCR” or “DAT” respectively (see page 29).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting an Onkyo RI Dock (Remote Interactive Dock)
The following diagram shows how to connect an optional Onkyo RI Dock (Remote Interactive Dock).
Connect the CD receiver’s DOCK/CDR IN jacks (DOCK IN jacks on the CR-315) to the RI Dock’s AUDIO OUT jacks.
CR-515’s
rear panel
LINE 1
White
IN
OUT
MD/
TAPE
Red
IN
Analog audio cable (RCA)
R
----
L
OUT
S VIDEO OUT
AUDIO OUT
DC IN
Red
DOCK/
CDR
IN
Onkyo RI Dock’s rear
panel
R
L
White
cable supplied
with the RI Dock
CR-315’s
rear panel
Red
DOCK
White
Red
IN
White
OUT
MD/
TAPE
Analog audio cable (RCA)
IN
R
L
R
----
L
S VIDEO OUT
AUDIO OUT
DC IN
Onkyo RI Dock’s rear
panel
cable supplied
with the RI Dock
: Signal flow
What can you do with
?
• Connecting an Onkyo RI Dock to the CD receiver with an
cable allows you to control the RI Dock with the CD
receiver’s remote controller. In addition, when playback is started on the RI Dock, the CD receiver will automatically
select it as the input source.
• To use
, you must connect the RI Dock to the CD receiver with an
cable and an analog audio cable (RCA).
On the RI Dock, set the MODE switch to “HDD.” See the RI Dock’s instruction manual for details.
CR-515
• To use
unless you’ve changed it, it can be left as it is (see page 29).
, the Input Display for the DOCK/CDR jacks must be set to “DOCK.” Since this is the default setting,
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting an Onkyo CD Recorder (CR-515)
The following diagram shows how to connect an optional Onkyo CD recorder.
Connect the CD receiver’s DOCK/CDR OUT jacks to the CD recorder’s INPUT (REC) jacks, and connect the CD
receiver’s DOCK/CDR IN jacks to the CD recorder’s OUTPUT (PLAY) jacks.
Onkyo CD recorder’s
CR-515’s rear panel
rear panel
LINE 1
INPUT OUTPUT
IN
REMOTE
(REC) (PLAY)
CONTROL
L
Analog audio cable (RCA)
OUT
MD/
TAPE
R
Red
IN
OUT
White
White
DOCK/
CDR
IN
White Red Red White
R
L
Red
cable supplied with
the Onkyo CD recorder
: Signal flow
What can you do with
?
• Connecting an Onkyo CD recorder to the CD receiver with an
cable allows you to control the CD recorder with
the CD receiver’s remote controller. In addition, when playback is started on the CD recorder, the CD receiver will
automatically select it as the input source.
• To use
(RCA). In addition, the Input Display for the DOCK/CDR jacks must be set to “CDR” (see page 29).
• Some -capable components have two jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional -capable components.
, you must connect the Onkyo CD recorder to the CD receiver with an
cable and an analog audio cable
Connecting a Portable Audio Device
The following diagram shows how to connect a portable audio device (e.g., MP3 player, MD player, CD player).
Connect the CD receiver’s LINE 2 IN jack (LINE IN jack on the CR-315) on the front panel to the portable audio
device’s output jack.
Depending on the type of output jack on the portable audio device, you may need to buy a suitable cable. The CD
receiver’s LINE 2 IN jack (LINE IN jack on the CR-315) accepts a stereo miniplug.
CR-515’s front panel
Portable audio device’s output jack
Stereo miniplug cable
: Signal flow
Notes:
• Use a connecting cable that doesn’t have any attenuation resistors in it.
• If you connect a portable audio device’s headphone output to the CD receiver’s LINE2 IN jack (LINE IN jack on the
CR-315), turn down the volume on the portable audio device before you connect it.
• When you connect a portable audio device to the CD receiver, make sure you connect it to the LINE 2 IN jack (LINE
IN jack on the CR-315) and not the adjacent PHONES jack. If you connect to the PHONES jack by mistake, it may
cause the PHONES output to malfunction.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting a Component with a Digital Audio Output (CR-515 Asian model only)
The following diagram shows how to connect a component with an optical digital audio output, such as a CD recorder,
MD recorder, games console, satellite tuner, or personal computer.
Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the other component.
You can change the Input Display for the OPTICAL DIGITAL IN to DIGITAL, CDR, PC, or GAME so that it matches
the type of component that you connect (see page 29).
Satellite tuner, CD
recorder, etc.
: Signal flow
DIGITAL
OUTPUT
CR-515 Asian model’s
rear panel
Optical digital audio cable
Personal computer
Connecting an Onkyo Component with a Digital Audio Output
The following diagram shows how to connect an Onkyo component with an optical digital audio output.
Connect the CD receiver’s OPTICAL DIGITAL IN jack to an optical digital audio output on the Onkyo component.
Onkyo component with a
digital audio output
CR-515 Asian model’s
DIGITAL
INPUT OUTPUT
OUTPUT
REMOTE
(REC)
(PLAY)
rear panel
CONTROL
L
Analog audio cable (RCA)
OUT
Red
MD/
TAPE
R
IN
White
Red
OUT
DOCK/
CDR
IN
cable
White
White Red
Red White
R
L
Optical digital audio cable
: Signal flow
What can you do with
?
• Connecting an Onkyo component to the CD receiver with an
cable allows you to control the component with the
CD receiver’s remote controller. In addition, when playback is started on the component, the CD receiver will auto-
• To use
, you must connect the Onkyo component to the CD receiver with an
cable and an analog audio cable
(RCA). In addition, you must change the Input Display for the DIGITAL IN so that it matches the type of component
that you connect. When you connect a CD recorder to the DOCK/CDR jacks and OPTICAL DIGITAL IN jack, you
must set the Input Display for DOCK/CDR to “CD-R,” and set the Input Display for OPTICAL DIGITAL IN to
“CD-R/dig” (see page 29).
• If you connect an audio processor such as the Onkyo UE-205, you must set the Input Display for DOCK/CDR to
“PC,” and set the Input Display for OPTICAL DIGITAL IN to “PC/dig,” otherwise the wrong input source may be
selected when playback starts (see page 29).
• Some
-capable components have two
jacks. They’re both the same, so you can use either one. The extra jack
is for connecting additional
-capable components.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components—Continued
Connecting a TV
Connect the CD receiver’s LINE 1 IN jacks (use the DOCK IN jacks on the CR-315) to the TV’s audio output jacks.
TV
CR-515’s rear panel
LINE 1
White
IN
OUT
Red
MD/
TAPE
IN
Red
White
OUT
DOCK/
CDR
IN
Analog audio cable (RCA)
R
L
: Signal flow
Hint:
To listen to the TV, select the LINE 1 input source (select DOCK on the CR-315).
Connecting the Power Cord
Notes:
• Before connecting the power cord, connect all of your speakers and AV components.
• Turning on the CD receiver may cause a momentary power surge that might interfere with other electrical equipment
on the same circuit. If this is a problem, plug the CD receiver into a different branch circuit.
• Do not use a power cord other than the one supplied with the CD receiver. The supplied power cord is designed
exclusively for use with the CD receiver and should not be used with any other equipment.
• Never disconnect the power cord from the CD receiver while the other end is still plugged into a wall outlet. Doing
so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the CD receiver.
CR-515
CR-315
DOCK
IN
LINE
IN
1
OUT
OUT
MD/
TAPE
MD/
TAPE
IN
IN
R
L
OUT
DOCK/
CDR
IN
R
L
AC INLET
AC INLET
1
1
2
2
To wall outlet
To wall outlet
Supplied power cord
Supplied power cord
Connect the supplied power cord to the CD receiver’s AC INLET.
1
2
Plug the power cord into a suitable wall outlet.
The STANDBY indicator lights up.
To set the clock with the AccuClock function, the CD receiver must be able to receive RDS radio stations, which means
an FM antenna must be connected (see page 16).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
First Time Setup (European Model Only)
Setting the Clock with the AccuClock Function (European Model Only)
To use theAccuClock function, the CD receiver must be able to receive RDS radio stations, which means an FM antenna
must be connected. Be sure to connect an FM antenna before attempting to use this function (see page 16).
The very first time you turn on the CD receiver, theAccuClock function automatically sets the CD receiver’s clock based
on the CT (Clock Time) information present in an RDS radio broadcast. While the clock is being set, “Wait …” flashes
on the display, as shown. Note that it may take up to 5 minutes to set the clock.
When the clock has been set, the message “Clock Adjusted” scrolls across the display, then the day and time are dis-
played for a while, as shown.
The AccuClock function automatically updates the clock daily at 2 A.M., 3 A.M., and 2 P.M.
If for some reason the clock cannot be set automatically, see “Setting AccuClock to Use a Specific Station (European
Model Only)” on page 47 and “Setting the Clock Manually” on page 48.
Turning Off the AccuClock Function
If you don’t want AccuClock to automatically update the clock each day, you can turn it off as follows.
Press the [TIMER] button repeat-
edly until “Clock” appears on the
display.
1
Press [ENTER].
“*AccuClock*” appears on the display.
2
TIMER
YES/MODE
ENTER
The asterisks indicate that the
AccuClock function is on.
To turn off AccuClock, press the
[YES/MODE] button.
3
The asterisks disappear, indicating that
the AccuClock function is off. To turn
AccuClock back on again, press the
[YES/MODE] button so that the aster-
isks are displayed.
Note:
The AccuClock function cannot be turned off until the
clock has been set.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
STANDBY/
ON
STANDBY indicator
INPUT
/
STANDBY/ON
VOLUME
VOLUME
/
PHONES
INPUT
Turning On the CD Receiver
Selecting the Input Source
You can select CD, AM, FM, or a connected component
(TAPE, DOCK, LINE, DIGITAL) as the input source.
To select the input source, press the remote controller’s
INPUT [ ]/[ ] buttons repeatedly. On the CD
receiver, press the [INPUT] button repeatedly. The input
sources are selected in the following order.
Remote
controller
CD receiver
• CR-515
To turn on the CD receiver, press the [STANDBY/ON]
button on the CD receiver or remote controller. The
STANDBY indicator goes off.
*1, *2
DIGITAL
CD
FM
AM
1
1
Press the [STANDBY/ON] button again to set the CD
receiver to Standby. The STANDBY indicator lights up.
*
*
LINE2
LINE1
DOCK
• CR-315
CD
Tip:
1
*
FM
AM
DOCK
TAPE
When you start playback on (or turn on) an Onkyo RI
Dock, CD recorder, MD recorder, or cassette deck that’s
connected to the CD receiver with an
log audio cable, the CD receiver turns on automatically.
Similarly, when you set the CD receiver to On or
Standby, the other component will also be set to On or
Standby.
LINE
cable and ana-
*1 Input Display can be changed (see page 29).
*2 CR-515 Asian model only.
Using Headphones
Turn down the volume, then connect your stereo head-
phones to the PHONES minijack.
You can adjust the volume and mute the sound, as
explained earlier.
The speakers output no sound while the headphones are
connected.
Adjusting the Volume
Remote
controller
CD receiver
PHONES jack
Turn the [VOLUME] control clockwise to increase the
volume or counterclockwise to decrease it.
You can also use remote controller’s VOLUME
[
]/[ ] buttons.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation—Continued
CR-515
CR-315
TONE
/
ENTER
DIRECT TONE
S.BASS
MUTING
DIRECT
Adjusting the Bass and Treble
Using the Direct Function
To turn the Direct function on or off, press
the [DIRECT] button on the CD receiver.
When the Direct function is off, the tone
controls can be used to adjust the sound.
When the Direct function is on, the tone
controls are bypassed, so you can enjoy a
pure sound, and the DIRECT indicator lights up.
Press the [TONE] button to select
Bass.
1
Use the Previous and Next
2
[
]/[
] buttons to adjust the
DIRECT indicator
bass.
The default setting is “ 0.” You can
adjust the bass and treble from –3 to +3.
Press [ENTER], and then use the
On the remote controller, press the [TONE] button for 3
seconds to turn on the Direct function.
Previous and Next [
]/[
] but-
tons to adjust the treble.
On the CR-515, the [DIRECT] button’s indicator lights
up when the Direct function is on.
Notes:
• If you press no buttons for 8 seconds,
the previous display will appear auto-
matically.
• If you press the [TONE] button while
the Direct function is on, the Direct
function will be turned off.
Muting the Sound
To mute the output of the CD
receiver, press the remote con-
troller’s [MUTING] button.
The MUTING indicator
flashes on the display. On the
CR-515, the volume control
indicator flashes, too.
On the CR-515, you can also use the [TONE] button and
multi control on the front panel to adjust the bass and
treble.
MUTING indicator
Using the Super Bass Function
To turn on the Super
Bass function, press the
[S.BASS] button.
The S.BASS indicator lights
To unmute the CD receiver, press the [MUTING] button
again.
up.
Tips:
To turn off the Super Bass function, press the [S.BASS]
button again.
While the CD receiver is muted:
• Turning the [VOLUME] control on the CD receiver or
pressing the VOLUME [ ]/[ ] buttons on the
remote controller will unmute the CD receiver.
• If you turn the CD receiver off, the next time you turn
it on, the CD receiver will be unmuted.
On the CR-515, you can also use the [TONE] button on
the front panel. Press the [TONE] button for 3 seconds to
turn on the Super Bass function.
Note:
If you press the [S.BASS] button while the Direct func-
tion is on, the Direct function will be turned off.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation—Continued
Changing the Input Display
You can choose what name is displayed when an input source is selected so that it matches the type of component that
you’ve connected to the MD/TAPE IN, DOCK/CDR IN, or DIGITAL IN. When you connect an Onkyo
component, it’s important that you select the input source name that matches the type of component for
properly.
-capable
to work
Depending on the input source selected
in step 1, the input source names are
selected in the following orders:
INPUT
/
TAPE
MD
VIDEO
MENU/NO/
CLEAR
DAT
YES/MODE
ENTER
DOCK
CD-R
/
PC
DIGITAL
CD-R/dig
GAME/dig
PC/dig
Use the INPUT [ ]/[ ] buttons
to select the input source whose
name you want to change.
CR-515: TAPE, DOCK, DIGITAL*
(*Asian model only)
1
2
Press [ENTER] to confirm your
selection.
4
CR-315: TAPE
“Complete” appears on the display.
Press and hold the
[MENU/NO/CLEAR] button until
“Name Select?” flashes on the
display, and then press [ENTER].
On the CR-515, you can also use the front panel con-
trols.
1 Use the [INPUT] button to select the input source
whose name you want to change.
2 Push the multi control to select “Name Select?,” and
then push it again.
3 Turn the multi control to select the new input source
name.
4 Push the multi control to confirm your selection.
Use the Previous or Next
Input Source Name Abbreviations
3
[
]/[
] button to select the
Sometimes the input source name may be displayed as a
2-letter abbreviation, as per the following table.
new input source name.
Full name
CDR
Abbreviation
CR
DT
DG
GM
DC
LI
DAT
DIGITAL
GAME
DOCK
LINE
LINE1
LINE2
MD
L1
L2
MD
PC
TP
VD
PC
TAPE
VIDEO
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs
CR-515
CR-315
Display
Display
Disc tray
Disc tray
/
/
Selecting Tracks (CR-515)
Press the Eject [ ] button to open
the disc tray.
1
To return to the beginning of the track
currently playing, turn the multi control
a little to the left.
Tip:
Pressing the Eject [ ] button while the
CD receiver is on Standby will turn on
the CD receiver and open the disc tray.
Turn the multi control further to select
earlier tracks.
the left to select the previous track.
Place the CD on the tray with the
label-side facing up.
2
3
Turn the multi control to the right to select subse-
quent tracks.
• On MP3 CDs, you can select MP3 files in other folders
(see page 32).
Place 8 cm CDs in the center of the tray.
To start playback, press the
Play/Pause [
] button.
/
The disc tray closes and playback starts.
To stop playback:
Press the Stop [ ] button. Playback stops
automatically when the last track has
been played.
Selecting Tracks (CR-315)
To return to the beginning of the
track currently playing, press the
To pause playback:
Previous [
] button.
Press the Play/Pause [
The Pause indicator appears. To
resume playback, press the Play/Pause
] button again.
] button.
/
Press the Previous [
repeatedly to select earlier tracks.
] button
[
/
[
] button will select the previous track.
To remove the CD:
Press the Next [
sequent tracks.
] button repeatedly to select sub-
Press the Eject [ ] button to open the
disc tray.
• On MP3 CDs, you can select MP3 files in other folders
(see page 32).
“DISC TOTAL” lights up
while the disc informa-
tion is being displayed.
• Audio CD Display
Total number
of tracks
Total playing
time
• MP3 CD Display
Disc name
Total number
of folders
Total number
of files
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Using the Remote Controller
Use the number buttons as
shown in the examples below to
select tracks.
Press:
To select:
Track #8
Press to display more CD infor-
mation
Track #10
Track #34
Press to fast forward or fast
reverse
During playback or while playback is
Used to enter numbers over 10.
With MP3 CDs, you can select files in
the current folder with these buttons.
paused, press and hold the Fast For-
ward [
Reverse [
] button to fast forward, or the
] button to fast reverse.
Press to select tracks
Press the Previous [
playing or paused track. Press it
repeatedly to select earlier tracks.
•
] button to
Press to start playback
Pressing this button while the CD
receiver is on Standby will turn on the
CD receiver and start playback.
•
Press the Next [
] button repeat-
edly to select subsequent tracks.
On MP3 CDs, you can select files in
other folders (see page 32).
Press to stop playback
Press to adjust the volume
Press the VOLUME Up [ ] button to
turn up the volume. Press the VOLUME
Down [ ] button to turn it down.
Press to pause playback
To resume playback, press the Pause
[
] or Play [ ] button.
Displaying CD Information
During playback or while playback is paused, press the remote controller’s [DISPLAY] button repeatedly to display the
following CD information.
Lights up while the elapsed track time
is being displayed.
“REMAIN”
Lights up while the remaining track
time is being displayed.
“TOTAL REMAIN”
Lights up while the remaining disc
time is being displayed.
During random playback, or if the total
time is more than 99 minutes and 59
seconds, “– –:– –” is displayed.
Note:
See page 34 for details on dis-
playing MP3 information.
On the CR-315, you can also use the CD receiver’s [DISPLAY] button to display this information.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Selecting MP3 Files
While playback is stopped, press
the [FOLDER] button.
1
2
On an MP3 CD, MP3 files may be organized in a hierar-
chically, with folders containing files and subfolders, as
shown below. On the CD receiver, there are two modes
for selecting MP3 files: Navigation mode andAll Folder
mode. In Navigation mode, you can select MP3 files by
navigating through the folder hierarchy, moving in and
out of folders and subfolders. In All Folder mode, all
folders appear at the same level, making it easy to select
folders regardless of the hierarchy.
The CD receiver enters Navigation
mode and “Root” appears on the dis-
play.
Press [ENTER].
The name of the first folder one level
down from root appears on the display.
Root
Folder #1
File #1
File #10
Folder #3
File #11
File #12
File #13
If the disc contains no folders, the name
of the first MP3 file is displayed.
Folder #2
Folder #4
File #14
Use the Previous and Next
3
4
[
]/[
] buttons to select
other folders and files at the
same level.
Folders that don’t contain MP3 files or
subfolders can’t be selected.
To access files or subfolders
inside another folder, select the
folder, and then press [ENTER].
File #18
Use the Previous and Next
[
]/[
] buttons to select the files
If you don’t select a specific MP3 file or folder for play-
back, all of the MP3 files on the CD will be played in
numerical order starting with file #1.
and subfolders within that folder.
To move up a level, press the
[MENU/NO] button.
Selecting MP3 Files in Navigation Mode
To start playback, press the
5
[ENTER] or Play/Pause [
button.
]
/
Playback will start with the specified
file or folder and continue until all of
the MP3 files on the disc have been
played.
FOLDER
MENU/NO
/
ENTER
On the CR-515, you can also use the multi control for
steps 2, 3, and 4. Turn the multi control to select files and
folders, and push it for ENTER.
With Navigation mode, you can select MP3 files by nav-
igating through the folder hierarchy. This mode can only
be used while playback is stopped.
If random mode or 1-folder mode is currently selected,
press the [YES/MODE] button to cancel it before pro-
ceeding.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Selecting MP3 Files in All Folder Mode
To start playback, press the
4
[ENTER] or Play/Pause [
button.
]
/
Playback will start with the specified
file or folder and continue until all of
the MP3 files on the disc have been
played.
Number
buttons
FOLDER
/
On the CR-515, you can also use the multi control for
steps 2, 3, and 4. Turn the multi control to select files and
folders, and push it for ENTER.
ENTER
To select an MP3 file in another folder during playback,
press the [FOLDER] button, select the folder by using
With All Folder mode, you don’t have to navigate the
folder hierarchy because all folders that contain MP3
files appear at the same level.
the Previous and Next [
control), and then press [ENTER] (or push the multi con-
trol). Now use the Previous and Next [ ]/[ ] but-
]/[
] buttons (or multi
If random playback is currently selected, press the
[YES/MODE] button to cancel it before proceeding.
tons (or multi control) to select the MP3 files within that
folder.
While playback is stopped, press
the [FOLDER] button for 2 sec-
onds.
1
■ Pausing Playback
To pause playback, press the Play/Pause [
To resume playback, press it again.
] button.
/
The CD receiver enters All Folder
mode and the name of the first folder
appears on the display.
■ Cancelling Navigation or All Folder Mode
To cancel Navigation mode or All Folder mode while
selecting MP3 files, press the Stop [ ] button.
■ Selecting MP3 Folders and Files by Number
Use the Previous and Next
2
1 Press the [FOLDER] button for 2 seconds to enter
[
]/[
] buttons to select the
All Folder mode.
other folders.
2 Use the number buttons as shown in the examples
You can select any folder that contains
MP3 files.
below to enter folder numbers.
To select:
Press:
To play the first file in the selected
folder, go to Step 4.
Folder #8
Folder #10
Folder #34
To access the files inside the
folder, press the [FOLDER] but-
ton.
3
Used to enter numbers over 10.
The name of the first MP3 file inside
the folder is displayed.
If playback is stopped, playback starts with the first
MP3 file in the specified folder. If playback is
already in progress, press [ENTER] to play the first
MP3 file in the specified folder.
Use the Previous and Next
[
]/[
] buttons to select the MP3
files within the folder.
3 Use the number buttons to enter the file number.
Playback starts.
If a folder contains more than 99 MP3 files, single-
and double-digit file numbers must be preceded by
zeros. For example, to specify file #5, press [5]. To
specify file #32, press [>10], [3], and [2].
To select another folder, press the
[FOLDER] button again, and then use
the Previous and Next [
buttons to select it.
]/[
]
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Playing the MP3 Files in Only One Folder
Displaying MP3 Information
You can display various information about the MP3 file
currently playing, including ID3 tags such as title, artist
name, and album name.
During playback, press the [DIS-
PLAY] button repeatedly to dis-
play the following MP3
information.
DISPLAY
YES/MODE
/
ENTER
Elapsed time: The length of time that the current MP3
file has been playing (default display). If the elapsed
time is more than 99 minutes and 59 seconds, “– –:– –”
is displayed.
Normally, all of the MP3 files in all of the folders on the
disc are played. With 1-folder playback, only the MP3
files in the specified folder are played.
File name: Name of the current MP3 file.
Press the [YES/MODE] button
repeatedly until the 1FOLDER
indicator appears.
1
Folder name: Name of the current folder.
1FOLDER indicator
Title name: Title of the current file (if ID3 tag present).
Artist name: Name of the artist (if ID3 tag present).
Album name: Name of the album (if ID3 tag present).
Use the Previous and Next
2
[
]/[
] buttons to select the
folder.
You can select any folder that contains
MP3 files.
To start playback, press the
3
[ENTER] or Play/Pause [
button.
]
/
Playback will start with the first MP3
file in the specified folder and continue
until all of the MP3 files in that folder
have been played.
Sampling rate and bit rate: Sampling rate and bit rate
of the current MP3 file.
Notes:
• On the CR-315, you can also use the CD receiver’s
[DISPLAY] button to display this information.
• To display the disc name, press the [DISPLAY] button
while playback is stopped.
cannot be displayed, an underscore will be displayed
in place of those characters. Alternatively, you can set
the CD receiver so that names containing such charac-
ters are displayed as “File n” or “Folder n,” “n” being
the file or folder number (see page 37).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
To remove tracks from the playlist:
Press the [CLEAR] button. Each press
removes the last track from the playlist.
Memory Playback
to 25 tracks.
Notes:
• If the total playing time is more than
99 minutes and 59 seconds, “– –:– –”
is displayed.
Number buttons
(see page 31)
• You can add up to 25 tracks to the
playlist. If you try to add more, the
message “Memory Full” appears.
(These buttons do
nothing during
memory playback)
MENU/NO/
CLEAR
To start memory playback, press
the Play [ ] button.
3
YES/MODE
ENTER
/
/
Track currently playing
On the CD receiver, press the Play/Pause
Memory playback can be set only when the input source
is set to CD and playback is stopped.
[
] button to start memory play-
/
back.
Press the [YES/MODE] button
repeatedly until the MEMORY indi-
cator appears.
1
Selecting Other Tracks During Memory Playback
To select other playlist tracks during memory playback,
use the remote controller’s Previous and Next
MEMORY indicator
[
]/[
] buttons.
Checking What’s on the Playlist
To check what tracks are on the playlist, with playback
stopped, use the Fast Reverse and Fast Forward
Use the Previous and Next
2
[
]/[
] buttons to select the
[
]/[
] buttons to scroll through the playlist.
first track you want to add to the
playlist, and then press [ENTER].
Removing Tracks from the Playlist
• While memory playback is stopped, press the
[CLEAR] button. Each press removes the last track
from the playlist.
• The playlist will be deleted when you cancel memory
playback, select random playback, turn off the CD
receiver, or remove the CD.
Track to be added
to the playlist
Total time of playlist
Repeat this step to add additional tracks
to the playlist.
You can also use the number buttons on
the remote controller to select tracks.
On the CR-515, you can also use the
multi control to add tracks to the playlist.
To select MP3 files for memory
playback:
In Navigation mode, use steps 1–4 on
page 32. In All Folder mode, use steps
1–4 on page 33.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Random Playback
Repeat Playback
With random playback, all of the tracks on the disc are
played in random order.
With repeat playback, you can play an entire CD repeat-
edly, play one track repeatedly, or combine it with mem-
ory playback to play the playlist repeatedly, or random
playback to play all of the tracks on the disc in random
order repeatedly. With an MP3 CD, you can combine
repeat playback with 1-folder playback to play all of the
tracks in a specified folder repeatedly.
YES/MODE/
SHUFFLE
REPEAT
Random playback can be set only when the input source
is set to CD and playback is stopped.
Press the [YES/MODE/SHUFFLE]
button repeatedly until the RAN-
DOM indicator appears.
1
RANDOM indicator
Press the [REPEAT] button repeat-
edly until the REPEAT or
REPEAT 1 indicator appears.
REPEAT or REPEAT 1 indicator
To start random playback, press
2
the Play [ ] button.
Repeat-1 playback can’t be combined with memory
playback, random playback, or 1-Folder playback.
Track currently playing
Cancelling Repeat Playback
• To cancel repeat playback, press the [REPEAT] button
repeatedly until both the REPEAT and REPEAT 1
indicators disappear.
• Repeat playback is cancelled when the CD is removed
or the CD receiver is set to Standby.
Cancelling Random Playback
• To cancel random playback, press the [SHUFFLE]
button repeatedly until the RANDOM indicator disap-
pears.
• Random playback is cancelled when the CD is
removed or the CD receiver is set to Standby.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Preferences
Setting MP3 Preferences
Below, the name of each preference is followed by its
options in parentheses, with the default option in bold.
With the MP3 preferences, you can change the way MP3
file information is displayed and the way MP3 CDs are
played.
Disc Name? (Display/Not Display)
This preference determines whether or not the disc name
File Name? (Scroll/Not Scroll)
This preference determines whether or not the file name
scrolls across the display when an MP3 file is selected.
In Navigation mode (see page 32), the file name scrolls
across the display regardless of this setting.
MENU/NO/
CLEAR
/
Folder Name? (Scroll/Not Scroll)
ENTER
This preference determines whether or not the folder
name scrolls across the display when an MP3 folder is
selected (in All Folder mode).
In Navigation mode (see page 32), the folder name
scrolls across the display regardless of this setting.
The MP3 preferences can be set only when playback is
stopped.
Bad Name? (Replace/Not Replace)
Press the [MENU/NO] button
repeatedly until “Disc Name?”
appears.
1
This preference determines whether or not file and folder
names that contain undisplayable characters are replaced
with “File n” or “Folder n,” “n” being the file or folder
number.When set to Not Replace, displayable characters
are displayed and underscore characters are used in place
of any undisplayable characters.
For ID3 tags, underscore characters are used in place of
undisplayable characters regardless of this preference.
Use the Previous and Next
2
[
]/[
] buttons to select the
ID3 Ver. 1? (Read/Not Read)
preference you want to change.
This preference determines whether or not version
1.0/1.1 tags are read and displayed. When set to Not
Read, version 1.0/1.1 tags are not displayed.
The preferences are explained in the next
column.
Press [ENTER].
3
4
ID3 Ver. 2? (Read/Not Read)
This preference determines whether or not version
2.2/2.3/2.4 tags are read and displayed. When set to Not
Read, version 2.2/2.3/2.4 ID3 tags are not displayed.
CD Extra? (Audio/MP3)
Use the Previous and Next
This preference applies to CD Extra discs and deter-
mines whether music in the audio session or MP3 files in
the data session are played.
[
]/[
] buttons to select the
preference’s options.
Joliet? (Use SVD/ISO9660)
This preference applies to MP3 discs in Joliet format and
determines whether the CD receiver reads the SVD data
or treats the disc as an ISO 9660 disc. Normally, this
preference doesn’t need to be changed.
Press [ENTER].
5
When the preference has been set, “Com-
plete” appears on the display.
SVD (Supplementary Volume Descriptor) supports long
file and folder names and characters other than letters
and numbers. Some CD burning software refers to the
Joliet format as “Windows format.”
To cancel the procedure at any point, press the
[MENU/NO] button.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CDs—Continued
Hide Number? (Disable/Enable)
This preference determines whether or not the numbers
at the beginning of file and folder names are hidden.
When you create an MP3 CD on a personal computer,
you cannot normally determine the playback order of the
files. However, if you number the MP3 files in order,
starting with 01, 02, 03, and so on, they will play in that
order. If you don’t want these numbers to appear on the
display, choose Enable.
The following table shows a few examples of numbered
file and folder names and how they will appear with the
Disable and Enable options.
Trk/Fld Num Option
File/folder name
Disable
Enable
Pops
01 Pops
01 Pops
10-Rock
10-Rock
Rock
16_Jazz
16_Jazz
Jazz
21th Century
05-07-20 Album
21th Century
21th Century
05-07-20 Album Album
Folder Key? (All Folder/Navigation)
This preference determines how the [FOLDER] button
works. When the All Folder option is selected, pressing
the [FOLDER] button once selects All Folder mode and
pressing and holding it for 2 seconds selects Navigation
mode. When the Navigation option is selected, pressing
the [FOLDER] button once selects Navigation mode and
pressing and holding it for 2 seconds selects All Folder
mode.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio
Tuning into Radio Stations
Press the [BAND] button repeat-
edly to select AM or FM.
1
2
YES/MODE
/
TUN/
TUN
(
Press the [YES/MODE] button
repeatedly to select Auto or Man-
ual.
)
•
Auto Tuning Mode
The AUTO indicator appears and ste-
reo radio reception is possible.
Manual Tuning Mode
BAND
•
The AUTO indicator is not displayed
and radio reception will be in mono.
AUTO indicator
When tuned into a station, the Tuned
indicator
appears. When tuned into a stereo FM station, the FM ST
indicator appears as well.
Use the Fast Reverse and Fast For-
ward [ ]/[ ] buttons to tune
into a station.
3
AUTO
FM ST
In Auto tuning mode, once a station is
found, tuning stops automatically.
The American model changes FM fre-
quency in 0.2 MHz steps, 10 kHz steps
for AM. For other models it’s 0.05 MHz
steps for FM and 9 kHz or 10 kHz steps
for AM.
In Manual Tuning mode, the frequency
stops changing when you release the but-
ton. Press the button repeatedly to
change the frequency one step at a time.
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Adjusting the Antennas
Adjusting and installing the FM antenna
Choose a location for the FM antenna while
listening to an FM station.
Adjusting the AM antenna
Adjust the location and position of theAM
antenna while listening to anAM station to
achieve the best reception.
1
2
Change the direction of the
antenna to achieve the best
reception.
Affix the antenna with a thumbtack. (Do not
push the thumbtack through the antenna.)
Caution: Be careful not to prick your finger!
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Presetting FM Stations Automatically (Auto Preset)
With the Auto Preset function, you can automatically preset all of the FM radio stations available in your area in one go.
Presets make it easy to select your favorite stations and eliminate the need to tune the radio manually each time you want
to change stations. The Auto Preset function does not preset AM radio stations (see page 41).
Auto Preset Caution!
Any existing presets will be deleted when the
Auto Preset function is run.
INPUT
/
MENU/NO/
CLEAR
/
ENTER
To start the Auto Preset function,
press [ENTER].
4
BAND
Up to 20 stations can be preset and pre-
sets are stored in frequency order.
Note:
Press the [BAND] or INPUT
1
Depending on your location, a preset may be stored with
[
]/[ ] buttons repeatedly until
no station and you will hear only noise when you select
it. In this case, delete the preset (see page 46).
“FM” appears.
or
On the CR-515, you can also use the front panel con-
trols.
1 Press the [INPUT] button repeatedly until “FM”
appears.
Make sure the FM antenna is positioned
to achieve the best possible reception.
2 Push the multi control, and then turn it to select
“AutoPreset?”
3 Push the multi control. The confirmation message
“AutoPreset??” appears.
trol.
Press the [MENU/NO] button, and
then use the Previous and Next
2
3
[
]/[
] buttons to select
“AutoPreset?”
• Select them (see page 42)
• Name them for easy identification (see page 44)
• Copy them (see page 45)
Press [ENTER].
The confirmation message “AutoPre-
set??” appears.
• Erase them (see page 46)
To cancel theAuto Preset function at this
point, press the [MENU/NO] button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Presetting AM/FM Stations Manually
With the Preset Write function, you can manually preset individual AM and FM radio stations. Presets make it easy to
select your favorite stations and eliminate the need to tune the radio manually each time you want to change stations.
FM stations can also be preset automatically (see page 40).
About Presets
• You can store up to 40 stations as presets and this can be any
combination of AM and FM stations. For example, 27 FM
and 13 AM or 32 FM and 8 AM.
• Although AM and FM presets share the same numbers,
they’re selected independently. For example, preset #1 will
store an AM station when the AM band is selected, and an
FM station when the FM band is selected.
MENU/NO/
CLEAR
/
ENTER
• Stations can be stored to presets in any order. For example,
you could store preset #5 first, #1 second, and so on.
Tune into the station that you want
to store as a preset.
To overwrite the previously stored sta-
tion, press the [YES/MODE] button.
To not overwrite the previously stored
1
2
Press the [MENU/NO] button, and
then use the Previous and Next
If the message “Memory Full” appears,
all 40 presets have been stored and you’ll
need to erase some presets before you
can store any more stations (see
page 46).
[
]/[
] buttons to select
“Preset Write?”
Press [ENTER].
3
Repeat steps 1 to 5 to preset more radio
stations.
6
The preset number flashes.
To cancel the Preset Write function at
this point, press the [MENU/NO] button.
On the CR-515, you can also use the front panel con-
trols.
1 Tune into the station you want to store as a preset
(see page 39).
2 Push the multi control, and then turn it to select “Pre-
setWrite?”
3 Push the multi control.
4 Turn the multi control to select a preset.
Use the Previous and Next
4
5
[
]/[
] buttons to select a
preset.
To store the station, press
[ENTER].
If no station has yet been stored to the
selected preset, “Complete” appears and
the station is stored.
Note:
If the current FM station supports RDS and PS (Program
Service Name), the station’s name will be displayed
instead of the frequency. (See page 43 for more on
RDS.)
If a station has already been stored in the
selected preset, the message “Over-
write?” appears.
• Select them (see page 42)
• Name them for easy identification (see page 44)
• Copy them (see page 45)
• Erase them (see page 46)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Selecting Preset Stations
You can also use the number but-
tons as shown in the examples
below to select presets.
You must store some presets before you can select them
(see pages 40 and 41).
To select:
Press:
Preset #8
INPUT
/
Preset #10
Preset #22
Number
buttons
Used to enter numbers over 10.
/
On the CR-515, you can also use the front panel con-
trols.
(
PRESET/
PRESET
)
1 Use the [INPUT] button to select AM or FM.
2 Turn the multi control to select a preset.
On the CR-315, you can also use the front panel con-
trols.
1 Use the [INPUT] button to select AM or FM.
BAND
2 Use the Previous and Next [
select a preset.
]/[
] buttons to
Use the [BAND] or INPUT [ ]/[
buttons to select AM or FM.
The preset you selected the last time you
listened to the radio will still be selected.
]
1
2
or
Use the Previous and Next
[
]/[
preset.
Press the Previous [
select the previous preset. Press the Next
] button to select the next preset.
] buttons to select a
] button to
or
[
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Displaying Radio Information
DISPLAY
Press the remote controller’s [DISPLAY] button repeatedly to display more radio information.
On the CR-315, you can also use the CD receiver’s [DISPLAY] button to display this information.
Frequency
AM/FM
* If the selected preset has no name, “No Name” appears
briefly and then the frequency is displayed. See “Nam-
ing Presets” on page 44.
*Preset name
Receiving RDS
RDS is only available on European models and only in
areas where RDS broadcasts are available.
What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data in FM radio signals. It was developed
within the European Broadcasting Union (EBU) and
many European FM radio stations use it these days.
The CD receiver supports and displays the Program Ser-
vice Name (PS) and Radio Text (RT) types of RDS data.
The RDS indicator appears on the display when the CD
receiver is tuned to an FM station that supports RDS.
Press the [DISPLAY] button repeatedly to dis-
play the following RDS information.
Frequency and preset number
Preset name (if preset has no name)
Program Service Name
Notes:
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
• The message “Waiting...” may appear while the RT
data is being received.
Radio Text (if available)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Note:
Naming Presets
Not all of the symbols can be entered by
using the number buttons. Use the Previ-
You can name presets for easy identification. The preset
name may contain of up to eight characters.
ous and Next [
] or [
] buttons to
select from the full range of symbols.
When you’ve selected the charac-
ter you want, press [ENTER], and
then choose the next character.
Number
buttons
DISPLAY
•
•
Editing characters:
To change or delete a character
you’ve already entered, use the
Rewind and Fast Forward [ ]/[
buttons to select it, and then select
another character, or press the
[CLEAR] button to delete it.
MENU/NO
ENTER
]
/
Inserting a new character:
To insert a new character, use the
Rewind and Fast Forward [ ]/[
buttons to select the character imme-
diately after the insertion point. That
character flashes. Use the Previous
Select the preset you want to
name (see page 42).
]
1
2
Press the [MENU/NO] button, and
then use the Previous and Next
and Next [
] or [
] buttons to
[
]/[
] buttons to select
select “ ,” press [ENTER], and
then select the new character.
“Name In?”
To cancel the Name In function, press the
[MENU/NO] button for 2 seconds.
When you’ve finished entering the
name, press the [YES/MODE] but-
ton.
The preset is named and “Complete”
appears on the display.
6
Press [ENTER].
3
4
Press the [DISPLAY] button
repeatedly to select one of the fol-
lowing character groups:
• “A” for uppercase letters.
• “a” for lowercase letters.
• “1” for numbers and symbols.
On the CR-515, you can also use the front panel con-
trols.
1 Select the preset you want to name (see page 42).
2 Push the multi control, and then turn it to select
“Name In?”
3 Push the multi control.
4 Turn the multi control to select a character, and then
push it.
Character group
5 Repeat step 4 to enter up to 8 characters.
•
•
Selecting letters:
5
Use the remote controller’s [DISPLAY] button to select
the character groups.
Press the number buttons repeatedly
to select the available letters. For
example, press the [2] button repeat-
edly to select: A, B, or C.
Selecting numbers and symbols:
Use the number buttons to select
numbers.
Press the [>10] button repeatedly to
select: (space) . / * - , ! ? & ’ ( )
Press the [0] button repeatedly to
select: 0 or (space)
Available Characters
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9
_
!
@
’ ”
'
,
<
.
>
#
$
%
&
*
=
;
:
+
-
/
(
)
?
(space)
(insert)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
To copy the preset, press
[ENTER].
5
Copying Presets
With the Preset Copy function, you can organize your
presets in the order you want. When you copy a preset,
its name is also copied.
If no station has yet been stored in the
destination preset, the station is copied
and “Complete” appears.
If a station has already been stored in the
destination preset, the message “Over-
write?” appears.
MENU/NO/
CLEAR
/
ENTER
To overwrite the previously stored sta-
tion, press [ENTER].
To not overwrite the previously stored
station, press the [MENU/NO] button.
Select the preset you want to copy
(see page 42).
1
On the CR-515, you can also use the front panel con-
trols.
1 Select the preset you want to copy (see page 42).
2 Push the multi control, and then turn it to select “Pre-
setCopy?”
Press the [MENU/NO] button, and
then use the Previous and Next
2
3 Push the multi control.
[
]/[
] buttons to select “Pre-
4 Turn the multi control to select the destination pre-
set.
setCopy?”
5 To copy the preset, push the multi control.
Tip:
If you favorite station is stored in preset #5 and you want
to make it preset #1, copy preset #5 to preset #1. To keep
the station that’s already stored in preset #1, you may
want to copy it to an unused preset first.
Press [ENTER].
3
4
The number of the preset to be copied
flashes.
Use the Previous and Next
[
]/[
] buttons to select the
destination preset.
The number of the destination preset
flashes.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the Radio—Continued
Erasing a Preset’s Name
Erasing Presets
Select the preset whose name you
want to erase (see page 42).
1
Press the [MENU/NO] button, and
then use the Previous and Next
2
MENU/NO/
CLEAR
[
]/[
] buttons to select
“NameErase?”
/
ENTER
Select the preset you want to
erase (see page 42).
1
2
To erase the preset’s name, press
the [YES/MODE] button.
The preset’s name is erased and “Com-
plete” appears on the display.
3
Press the [MENU/NO] button, and
then use the Previous and Next
[
]/[
] buttons to select
On the CR-515, you can also use the front panel con-
trols.
“PresetErase?”
1 Select the preset whose name you want to erase (see
page 42).
2 Push the multi control, and then turn it to select
“NameErase?”
3 To erase the preset’s name, push the multi control.
Press [ENTER].
A message requesting confirmation
appears.
3
4
To cancel the Preset Erase function at
this point, press the [MENU/NO] button.
To erase the preset, press
[ENTER].
The preset is erased and “Complete”
appears on the display.
On the CR-515, you can also use the front panel con-
trols.
1 Select the preset you want to erase (see page 42).
2 Push the multi control, and then turn the multi con-
trol to select “PresetErase?”
3 Push the multi control. The confirmation message
“Erase OK?” appears.
4 To erase the preset, push the multi control.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock
Setting AccuClock to Use a Specific Station (European Model Only)
The AccuClock function normally uses the FM station with the strongest signal to set the clock. However, if the clock
cannot be set properly using that station, you can specify which FM station the AccuClock function should use. This
must be an FM station that supports RDS CT (Clock Time) information.
When you’ve selected the station,
press [ENTER].
Press the [TIMER] button.
“Clock” appears on the display.
If the clock has already been set, a timer
option appears instead, in which case
you’ll need to press the [TIMER] button
repeatedly until “Clock” appears.
5
1
2
3
While the clock is being set, “Wait”
flashes on the display. It may take a few
minutes to set the clock. When the clock
has been set, the message “Clock
Adjusted” scrolls across the display, then
the day and time are displayed for a
while.
Press [ENTER].
“AccuClock”or “*AccuClock*” appears
on the display.
Notes:
• If the clock is not set correctly, specify
another FM station and try again or set
the clock manually (see page 48).
• The AccuClock function automati-
cally updates the clock every day. If
you don’t want it to, you can turn off
the AccuClock function (see page 26).
If “Manual Adjust” appears, use the Pre-
vious and Next [
]/[
] buttons to
select “AccuClock” or “*AccuClock*”.
Press [ENTER].
The frequency flashes on the display.
Use the Rewind and Fast Forward
4
[
]/[ ] buttons to tune into the
FM station.
Tip:
If you press the [YES/MODE] button
instead of using the Rewind and Fast For-
ward [ ]/[ ] buttons, the CD
receiver will automatically search for a
suitable station.
The RDS indicator appears when tuned
into a station that supports RDS.
The RDS indicator will flash while the
CD receiver searches for a station and
light up continuously when a station is
found.
RDS indicator
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock—Continued
Setting the Clock Manually
The time can be displayed in either 12- or 24-hour for-
mat.
Use the Previous and Next [
] buttons to set the time.
You can also use the remote controller’s
number buttons to enter the time.
]/
7
8
[
STANDBY/ON
CLOCK
CALL
Number
button
DISPLAY
For the 12-hour format, use the remote
controller’s [>10] button to select AM or
PM.
TIMER
/
MENU/NO/
CLEAR
ENTER
Press [ENTER].
The clock is set and the second dot starts
flashing.
Press the [TIMER] button repeat-
edly until “Clock” appears.
1
2
3
Displaying the Day and Time
To display the day and time, press the remote controller’s
[CLOCK CALL] button.
If the CD receiver is on Standby, the time is displayed for
8 seconds.
Press [ENTER].
Using the 12- or 24-hour Format
Use the Previous and Next [
] buttons to select “Manual
]/
[
To change the time format between 12-hour and 24-hour,
while the time is shown on the display, press the [DIS-
PLAY] button.
Adjust.”.
Displaying the Time in Standby Mode
Press [ENTER].
4
5
To set the CD receiver so that the time is displayed while
its on Standby, turn on the CD receiver, and then press
and hold its [STANDBY/ON] button for 2 seconds.
Note that having the time displayed in Standby mode
will consume a little more power.
Use the Previous and Next [
]/
[
] buttons to select the day of
the week.
You can select: SUN, MON, TUE, WED,
THU, FRI, or SAT.
Press [ENTER].
6
To cancel the Manual Adjust function at
this point, press the [MENU/NO] button.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers
ers for automated playback or recording, and a sleep timer
for turning the CD receiver off after a specified period.
Timer Examples
The following examples highlight some of the ways in
which you can use the timers.
The timers can be used with other Onkyo components
Timer 1: To wake up to your favorite radio station (pre-
set #1) every morning, set as follows:
that are connected to the CD receiver via
(see pages
Play➔FM 1➔Every➔Every Day➔On 7:00➔Off 7:30
If you want a radio alarm only on weekdays, select
“Days Set” instead of “Every Day” and specify
“MON–FRI.”
About the Timers
The various settings for the four programmable timers
are explained here. For details on the sleep timer, see
page 53.
Timer 2: To record a one-off radio show (preset #2) to a
cassette deck this Sunday, set as follows:
Rec➔FM 2➔TAPE➔Once➔SUN➔On 21:00➔Off 22:00
Timer Types
(You need an
-capable Onkyo cassette recorder or
Each timer can be programmed for playback (Play) or
recording (Rec).
MD recorder to do the recording.)
Timer 3: To record an FM radio show to a MiniDisc
recorder every day from Monday to Friday, set as fol-
lows:
Rec➔FM 1➔MD➔Every➔Days Set➔MON➔ FRI➔On
15:00➔Off 15:30
■ Play
Play mode can be used to start playback at a specified
time on the CD receiver or another Onkyo component
that’s connected to the CD receiver with an
cable.
You could use a Play timer to turn on the CD receiver
every morning, just like a radio alarm.
Timer Priority
■ Rec
If two or more timers are set to the same On time, the
lowest numbered timer has priority. For example:
Timer 1: 07:00 – 13:00 (This timer has priority.)
Timer 2: 07:00 – 12:30
Rec mode can be used to start playback on one compo-
nent and start recording on another component at a spec-
ified time. The recording component (e.g., Onkyo
cassette deck or MD recorder) must be connected to the
CD receiver with an
timer to record your favorite radio show every day.
If two or more timers overlap, the timer with the earliest
start time has priority. For example:
cable. You could use a Rec
Timer 1: 9:00 – 10:00
Timer 2: 8:00 – 10:00 (This timer has priority.)
Playback and Recording Components
If the On and Off times of two timers are the same, the
timer with the earliest start time has priority and the
other timer will fail. For example:
The playback component can be the CD receiver (AM,
FM, or CD), an Onkyo component (MD recorder, cas-
sette deck, etc) that’s connected to the CD receiver with
Timer 1: 0:00 – 1:00 (This timer has priority.)
Timer 2: 1:00 – 2:00
an
cable, or a component that’s connected to one of
the CD receiver’s inputs, perhaps one with its own built-
in timer.
The recording component can be an Onkyo MD recorder
or cassette deck that’s connected to the CD receiver with
Timer Indicators
When a timer has been set, the TIMER indica-
tor and the number of the timer appear on the
display. If the timer has been set to perform
recording, an underscore character appears
underneath the timer’s number.
an
cable.
Repeat Timers
Each timer can be programmed to work just once
(Once), every week (Every), every day (Every Day), or
on a range of days (Days Set).
Notes:
• The timers work only if the CD receiver is on Standby.
If it’s on when a timer is supposed to start playback or
recording, nothing will happen.
■ Once
The timer will work just once.
• While timed playback or recording is in progress, the
timer’s Off time cannot be changed.
• To use timed playback or recording with an external
component, make sure it’s properly connected to the
■ Every
The timer will work every week on the specified day and
time.
•
Everyday
CD receiver. Also, for
to work properly, make
The timer will work every day.
sure that the Input Display on the CD receiver is set to
match the type of component you’ve connected to the
MD/TAPE IN, DOCK/CDR IN, or DIGITAL IN (see
page 29).
•
Days Set
The timer will work on the specified range of days. With
this setting, you could set up a morning alarm for Mon-
day to Friday.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers—Continued
Programming the Timers
Notes:
Use the Previous and Next [
]/
3
• You must set the clock before you can program the
timers.
• Before programming a timer to turn on the radio, you
must preset the station you want to use. (See pages 40
and 41.)
[
] buttons to select the source,
and then press [ENTER].
• If you don’t operate any buttons for 60 seconds while
programming a timer, the procedure will be cancelled
and the previous display will reappear.
You can select the following sources:
CR-515
FM,AM, TAPE, DOCK, LINE1, LINE2,
DIGITAL, or CD.
STANDBY/ON
CR-315
Number buttons
FM, AM, TAPE, DOCK, LINE, or CD.
If you selected Rec, CD cannot be
selected as the source.
TIMER
If you selected AM or FM, use the
/
4
Previous and Next [
]/[
] but-
ENTER
tons to select the radio preset, and
then press [ENTER].
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4, and
then press [ENTER].
1
If you selected Rec, make sure the
name of the connected recorder is
flashing on the display, and then
press [ENTER].
5
6
If “Clock” appears, you need to set the
clock (see pages 26, 47, 48).
Use the Previous and Next [
] buttons to select Play or
]/
2
You can select TAPE or MD.
[
Rec, and then press [ENTER].
Use the Previous and Next [
] buttons to select Once or
Every, and then press [ENTER].
]/
[
Select Once for on-off operation. Select
Every to perform the same operation
every week.
or
your Onkyo cassette deck or MD
recorder is properly connected to the
MD/TAPE jacks (see pages 20 and 21)
and the Input Display is set accordingly
(see page 29).
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers—Continued
If you selected Once, use the Pre-
vious and Next [ ]/[ ] but-
tons to select the day, and then
press [ENTER].
You can select: SUN, MON, TUE, WED,
THU, FRI, or SAT.
Use the Previous and Next [
] buttons to specify the Off
time, and then press [ENTER].
]/
7
8
11
[
TIMER indicator
If you selected Every, use the Pre-
Underscore indicates
timer programmed for
recording
Number of
programmed
timer
vious and Next [
]/[
] but-
tons to select the day, Everyday, or
Days Set, and then press [ENTER].
You can select the following:
Use the Previous and Next [
] buttons to specify the CD
]/
12
[
MON
TUE
WED
THU
FRI
receiver’s volume level, and then
press [ENTER].
Days Set
Everyday
SAT
SUN
If you selected Days Set, use the
Previous and Next [ ]/[ ] but-
tons to select the first day, and
then press [ENTER].
The default setting is 10.
If you want to use your normal volume
level setting for the timer, press the Pre-
9
vious [
] button repeatedly until
“TimerVol.Off” appears on the display.
In this case, the timer will use the volume
level that was set before the CD receiver
was set to Standby.
Use the Previous and Next [
]/
Press the [STANDBY/ON] button to
set the CD receiver to Standby.
[
] buttons again to select the
13
last day, and then press [ENTER].
Notes:
• Be sure to set the CD receiver to
Standby, otherwise the timed opera-
tion will not work.
You can select only consecutive days.
• While a timed operation is in progress,
you can cancel it by pressing the
[TIMER] or [SLEEP] button.
• While timed recording is in progress,
the output of the CD receiver is muted.
To hear what’s being recorded, press
the [MUTING] button. Press it again
to mute the CD receiver.
Use the Previous and Next [
] buttons to specify the On
time, and then press [ENTER].
]/
10
[
You can also use the remote controller’s
number buttons to enter the time. For
example, to enter 7:29, press [>10], [0],
[7], [2], and [9].
• Memory, random, and 1-Folder play-
back cannot be used with the timers.
Notes:
To return to step 1 and start timer programming all over
again, press the [MENU/NO] button at any point in this
procedure.
• Once the On time is set, the Off time is
automatically set to one hour later.
• To ensure that the first few seconds of
a program are recorded when using
timer recording, set the On time
slightly ahead of the program’s start
time (about 1 minute).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers—Continued
Turning Timers On and Off
Checking Timer Settings
Once a timer has been programmed, you can turn it on or
off as necessary. For example, while you’re on holiday,
you may want to turn off the timer you use as an early-
morning alarm.
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4, and
then press [ENTER].
1
TIMER
/
MENU/NO/
CLEAR
Press [ENTER] repeatedly to see
all of the timer’s settings.
2
ENTER
Notes:
• You can change the settings by using
Press the [TIMER] button repeat-
edly to select timer 1, 2, 3, or 4.
the Previous and Next [
buttons.
• If you change the settings of a timer
that is off, that timer will be turned on.
If you don’t change any settings, the pre-
vious display reappears.
To return to the previous display at any
point in this procedure, press the
[MENU/NO] button.
]/[
]
1
2
When a timer has been programmed, its
number appears on the display.
Use the Previous and Next [
] buttons to selectTimer On or
Timer Off.
]/
[
or
After a few moments, the previous dis-
play reappears.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Timers—Continued
Using the Sleep Timer
With the sleep timer, you can set the CD receiver so that
it automatically turns off after a specified period.
SLEEP
Press the [SLEEP] button repeat-
edly to select the required sleep
time.
With the [SLEEP] button, you can set the
sleep time from 90 to 10 minutes in 10
minute increments.
Use the Previous and Next [
]/[
]
buttons to set the sleep time in 1 minute
increments from 99 to 1.
SLEEP indicator
When the sleep timer has been set, the
SLEEP indicator appears on the display,
as shown. The sleep time appears on the
display for about 8 seconds, then the pre-
vious display reappears.
Note:
The sleep timer will be ignored while
dubbing a CD to an Onkyo cassette deck
or MD recorder is in progress. The CD
receiver will automatically switch to
Standby when the dubbing is complete.
Checking the Remaining Sleep Time
To check the remaining sleep time, press the [SLEEP]
button.
Note that if you press the [SLEEP] button while the sleep
time is being displayed, you’ll shorten the sleep time by
10 minutes.
Canceling the Sleep Timer
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have any trouble using the CD receiver, look for a solution in this section.
If you can’t resolve the issue yourself, try resetting the CD receiver before contacting your Onkyo dealer.
To reset the CD receiver to its factory defaults, turn it on and, while holding down
the [ ] button, press the [STANDBY/ON] button.“Clear”will appear on the display
and the CD receiver will enter Standby mode.
Note that resetting the CD receiver will delete your radio presets and custom settings.
Power
Can’t turn on the CD receiver.
• Make sure that the power cord is properly plugged into the wall outlet (see page 25).
• Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
The CD receiver turns off unexpectedly.
• If the sleep timer has been set and the TIMER indicator is shown on the display, the CD receiver will turn off auto-
matically after a specified period.
• When timed playback or recording finishes, the CD receiver automatically switches to Standby mode.
• If the STANDBY indicator is flashing, the built-in amplifier protection circuit has been activated. This can happen if
there’s a short between the positive and negative wires of a speaker cable.
Audio
There’s no sound.
• Make sure the correct input source is selected (see page 27).
• Make sure the CD receiver is not muted (see page 28).
• Make sure the speakers are connected correctly (see page 18).
• Check all connections and correct as necessary (see pages 16 to 25).
• While headphones are connected, the speakers output no sound (see page 27).
The sound quality is not good.
• Make sure the speaker cables are connected with the correct polarity (see page 18).
• Make sure all audio connecting plugs are pushed in all the way (see page 19).
• The sound quality can be affected by strong magnetic fields, such as that from a TV. Try moving any such devices
away from the CD receiver.
• If you have any devices that emit high-intensity radio waves near the CD receiver, such as a cellular phone that’s being
used to make a call, the CD receiver may output noise.
• The CD receiver’s precision drive mechanism may emit a faint hissing sound while reading discs during playback or
when searching for tracks. You may be able to hear this noise in extremely quiet environments.
Audio output is intermittent when the CD receiver is subjected to vibration.
• The CD receiver is not a portable device. Use it in a location that’s not subject to shock or vibration.
Headphone output is intermittent or there’s no sound.
• This may be due to dirty contacts. Clean the headphones plug. See your headphones’instruction manual for cleaning
information. Also, make sure that the headphones cable is not broken or damaged.
Audio performance
• Audio performance will be at its best about 10 to 30 minutes after the CD receiver has been turned on and had time
to warm up.
• Using cable ties to bundle audio cables with speaker or power cables may degrade the sound quality, so don’t do it.
CD Playback
Playback jumps.
• The CD receiver is being subjected to vibration or the disc is scratched or dirty (see page 15).
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
Can’t add tracks to the playlist for memory playback.
• Make sure there’s a disc in the CD receiver. Also, you can only add valid track numbers. For example, if the CD
contains 11 tracks, you cannot add track #12.
The disc will not play.
• Make sure the disc has been loaded correctly, with the label-side facing up.
• Check to see if the surface of the disc is dirty (see page 15).
• If condensation is suspected, turn on the CD receiver and leave it for 1 hour before playing any discs.
• Some CD-R/RW discs may not be playable (see page 14).
It takes a long time for playback to start.
• It may take the CD receiver a while to read CDs that contain many tracks or files.
Tuner
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all stations, or
the ST indicator doesn’t light up when tuned to a stereo FM station.
• Check the antenna connections (see page 16).
• Change the position of the antenna (see page 39).
• Move the CD receiver away from a nearby TV or computer.
• Cars or airplanes can cause noisy interference.
• The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
• Try setting FM mode to mono (see page 39).
• When listening to an AM station, noise may be heard when you operate the remote controller.
• If none of the above improves the reception, install an outdoor antenna (see page 17).
If a power outage occurs or the power cable is disconnected:
• If the preset stations are lost, preset them again (see pages 40, 41).
• The clock and timer settings will be lost. Set the clock and timers again (see pages 47, 48).
Can’t adjust the frequency of the radio.
• Use the Fast Reverse and Fast Forward [
]/[
] buttons to change the frequency of the radio (see page 39).
RDS doesn’t work.
• The FM station you are tuned to doesn’t support RDS.
• Install an outdoor FM antenna (see page 17).
• Change the position or direction of your outdoor FM antenna (see pages 17, 39).
• Move the FM antenna as far away as possible from fluorescent lights (see page 39).
Remote Controller
The remote controller doesn’t work properly.
• Make sure the batteries have been installed with the correct polarity (+/–) (see page 5).
• Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)
• The remote controller is too far away from the CD receiver, or there’s an obstacle between them (see page 5).
• The CD receiver’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
• The CD receiver is located behind the glass doors of a audio rack or cabinet.
External Components
Interactive control with other Onkyo
-capable components is not working.
• Make sure the
cables and analog audio cables are connected correctly (see pages 19 to 25). Connecting only an
cable won’t work.
• Make sure the Input Display matches the type of device that you’ve connected to the CD receiver (see page 29).
• When recording an MP3 CD to an Onkyo recording component, recording will start without performing a peak search
when the [CD DUBBING] button is pressed on the recording component. This is not a malfunction.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting—Continued
No sound is heard from a connected component.
• Make sure the optical digital audio cable is not bent or damaged.
• On the external component, set the digital output format to PCM, as the CD receiver supports only PCM signals.
No sound is heard from your turntable.
• Make sure the turntable has a built-in phono equalizer.
Timers
Timer playback or recording doesn’t work.
• Make sure the clock has been set correctly (see page 47).
• Timed operation will fail if the CD receiver is on at the specified On time, so make sure it’s set to Standby (see
page 51).
• The timer may overlap with another timer. If you program several timers, make sure they don’t overlap (see page 49).
• If you press the [SLEEP] or [TIMER] button while a timed operation is in progress, the timer will be cancelled.
• Make sure the
• If you’re using an Onkyo component for timed playback or recording, you must set the Input Display to match that
component (see page 29).
The time is not displayed in Standby mode.
• Set the CD receiver so that the time is displayed in Standby mode (see page 48).
Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s
malfunction. Before you record important data, make sure that the material will be recorded correctly.
The CD receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this
should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
CR-515
AC 230 V, 50 Hz AC 220–230 V, 50/60 Hz AC 120 V, 60 Hz
CR-315
General
Power Supply:
Power Consumption:
Stand-by Power Consumption:
Dimensions (W × H × D):
Weight:
56 W
0.25 W
North American: 60 W
North American: 0.15 W Others: 0.25 W
13-7/8") 205 116 352.5 mm (8-1/16" 4-9/16" 13-7/8")
Others: 56 W
205
×
116
×
353 mm (8-1/16"
×
4-9/16"
×
×
×
×
×
4.3 kg (9.5 lbs.)
4.2 kg (9.3 lbs.)
Audio Inputs
Digital Inputs:
Analog Inputs:
1 (optical)
4 (LINE1, LINE2, DOCK, TAPE)
0
3 (LINE, DOCK, TAPE)
Audio Outputs
Analog Outputs:
Subwoofer Pre Outputs:
Speaker Outputs:
Phones:
2 (DOCK, TAPE)
1 (TAPE)
1
2
1
1
2
1
CR-515
CR-315
Amplifier Section
Power Output:
North American: 14 W + 14 W (8Ω, 1 kHz, FTC)
European:
Asian:
2ch
IEC)
×
20 W (4Ω, 1 kHz, 2ch driven,
19 W + 19 W (4Ω, 1 kHz, FTC)
European:
Asian:
2ch
×
19 W (4Ω, 1 kHz,
19 W + 19 W (8Ω, 1 kHz, JEITA)
26 W + 26 W (4Ω, 1 kHz, JEITA)
2ch driven, IEC)
18 W + 18 W (8Ω, 1 kHz, JEITA)
25 W + 25 W (4Ω, 1 kHz, JEITA)
Dynamic Power:
22 W + 22 W (3Ω, Front)
20 W + 20 W (4Ω, Front)
14 W + 14 W (8Ω, Front)
22 W + 22 W (3Ω, Front)
20 W + 20 W (4Ω, Front)
14 W + 14 W (8Ω, Front)
0.9% (Power Rated) 0.4% (1 kHz, 1 W)
25 (Front, 1 kHz, 8 Ω)
150 mV/50 kΩ (TAPE)
150 mV/2.2Ω (REC OUT)
10 Hz–100 kHz/ 3 dB (TAPE)
6 dB, 80 Hz (BASS)
THD (Total Harmonic Distortion): 0.4% (1 kHz, 1 W)
Damping Factor:
Input Sensitivity and Impedance:
Output Level and Impedance:
Frequency Response:
Tone Control:
25 (Front, 1 kHz, 8 Ω)
150 mV/50 kΩ (TAPE)
150 mV/2.2Ω (REC OUT)
10 Hz–100 kHz/ 3 dB (TAPE)
6 dB, 80 Hz (BASS)
8 dB, 10 kHz (TREBLE)
+7 dB, 80 Hz (S.BASS)
100 dB (LINE, IHF-A)
4 Ω–16 Ω
8 dB, 10 kHz (TREBLE)
+7 dB, 80 Hz (S.BASS)
100 dB (LINE, IHF-A)
4 Ω–16 Ω
Signal to Noise Ratio:
Speaker Impedance:
CR-515
CR-315
Tuner Section
FM
Tuning Frequency Range:
87.5 MHz–108.0 MHz
North American:
Others:
87.5 MHz–107.9 MHz
87.5 MHz–108.0 MHz
Usable Sensitivity:
Signal to Noise Ratio:
Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF)
Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A)
Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF)
Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A)
THD (Total Harmonic Distortion): Stereo: 0.5% (1 kHz)
Mono: 0.3% (1 kHz)
Stereo: 0.5% (1 kHz)
40 dB (1 kHz)
Mono: 0.3% (1 kHz)
Stereo Separation:
40 dB (1 kHz)
AM
Tuning Frequency Range:
522 kHz–1611 kHz
North American: 530 kHz–1710 kHz
Others:
522 kHz–1611 kHz
Usable Sensitivity:
Signal to Noise Ratio:
300 dBf (30 µV)
40 dB
300 dBf (30 µV)
40 dB
THD (Total Harmonic Distortion): 0.7%
0.7%
CR-515
CR-315
CD
Frequency Response:
4 Hz–20 kHz
96 dB
0.005%
10 Hz–20 kHz
95 dB
0.009%
Audio Dynamic Range:
THD (Total Harmonic Distortion):
Wow and Flutter:
Below threshold of measurability
Below threshold of measurability
Audio Output/Impedance (Analog): 1.3 V/1.0 kΩ
1.3 V/1.0 kΩ
Specifications and features are subject to change without notice.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
I0609-2
SN 29344258A
(C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 4 2 5 8 A *
Download from Www.Somanuals.com. All Manuals Search And Download.
|