Omnitron Systems Technology Network Card 10T 2 User Manual

To find out about individual chassis A and B  
backplane links, refer to the specific chassis’ user  
manual.  
DIP-Switch is in the “OFF” position, the iConverter  
10T/2 module’s A backplane Ethernet port will be isolated  
from the backplane.  
OVERVIEW:  
to the slot on its left using the “A” link and to the slot on  
its right using the “B” link.  
The iConverter 10T/2 converter supports the IEEE  
802.3 standard and converts 10BASE-T cabling (UTP)  
to 10BASE-2 coax cabling. The iConverter supports  
Half-Duplex 10Mbps Ethernet and provides a crossover  
UTP switch for easy attachment to hubs, switches and  
workstations. It also features a termination switch for  
easy coax termination.  
The 10T/2 can be used as a standard two-port UTP to  
fiber converter. It can also use its two additional  
10/100 backplane Ethernet ports to connect to adjacent  
modules and accommodate flexible network  
configurations like In-Band management and multi-  
module configurations. The iConverter 19-Module,  
5-Module or 2-Module Chassis have backplanes that  
facilitate connectivity between adjacent modules.  
®
In this example, the module on the left is an NMM and  
it connects via its “A” link to the 10T/2 facilitating  
In-Band management. The module on the right is an  
iConverter 10/100 module and it connects via its “B”  
link to the 10T/2 facilitating a 2-port 10/100 Ethernet  
hub/switch with a 10BASE-2 port and a fiber uplink. This  
3-module configuration provides an effective  
10BASE-2 to 10/100 managed switch with a fiber uplink.  
iConverter 10T/2 User Manual  
Front Plane RJ45 Crossover “= / X” Switch:  
Backplane B Enable “B-EN” DIP-Switch:  
When connecting to a workstation, set this DIP-Switch  
to Straight-Through “=” (factory setting). When  
connecting to a hub or switch, set to Crossover “X”.  
When the Backplane B Enable “B-EN” DIP-Switch is in  
the “ON” position, the iConverter 10T/2 module’s B  
backplane Ethernet port is enabled. This port allows  
connectivity to adjacent modules and facilitates  
In-Band management of the Network Management  
Module (NMM). When the Backplane B Enable “B-EN”  
DIP-Switch is in the “OFF” position, the iConverter  
10T/2 module’s B backplane Ethernet port will be isolated  
from the backplane.  
BOARD MOUNTED DIP-SWITCH SETTINGS:  
ON  
“TST” DIP-Switch:  
OFF  
1
2
3
4
This switch is reserved for factory use, and should be  
left in the “OFF” position.  
The 10T/2 can be used in an unmanaged or managed  
fashion. When unmanaged, it can be installed in a  
chassis without a Network Management Module (NMM).  
To be managed, a NMM module must be installed in the  
same chassis.  
Fig. 2 Board Mounted DIP-Switches  
Coax Termination “T-IN” DIP-Switch:  
Model Type  
8340-0  
Connectors  
UTP  
Distance  
100m  
When the Coax Termination “T-IN” DIP-Switch is in the  
“ON” position, the coax port is terminated. Use this  
DIP-Switch setting when this coax port is at the end of  
the network.  
Due to the Ethernet 5-4-3 rule, no more than  
4 iConverter 10T/2 modules can be  
linked together via the backplane buses.  
Coax  
185m  
For wide temperature (-40 to 60º C) modules, add a "W" to the end  
of the model number. Consult factory for other configurations and  
extended temperature (-40 to +75º C) modules.  
Backplane A Enable “A-EN” DIP-Switch:  
Fig. 1 10T/2 Application Example  
PORT STRUCTURE:  
When the Backplane A Enable “A-EN” DIP-Switch is in  
the “ON” position, the iConverter 10T/2 module’s “A”  
backplane Ethernet port is enabled. This port allows  
connectivity to adjacent modules and facilitates  
In-Band management of the Network Management  
Module (NMM). When the Backplane A Enable “A-EN”  
Fig. 1 depicts a chassis with three modules plugged  
into three of its adjacent backplane slots. The adjacent  
slots are connected to the “A” and “B” backplane links  
via the module’s “A” and “B” backplane Ethernet ports.  
In this example, the 10T/2 in the center slot connects  
This example shows how the 10T/2 can be used either  
as a traditional managed or unmanaged media converter  
or to create flexible and effective network hub/switch  
configurations.  
Page 1  
Page 2  
Page 3  
Page 4  
Page 5  
Technical Support:  
Warning  
maintenance of the equipment by Buyer, Buyer-  
supplied equipment, Buyer-supplied interfacing,  
unauthorized modifications or tampering with equipment  
(including repairs of equipment by personnel not  
specifically authorized and certified by Omnitron), or  
misuse, or operating outside the environmental  
specification of the product (including but not limited  
to voltage, ambient temperature, radiation, unusual  
dust, etc.), or improper site preparation or maintenance.  
MOUNTING AND CABLE ATTACHMENT:  
iConverter modules are hot-swappable and can be  
installed into any chassis in the iConverter family.  
1. Carefully slide the iConverter module into the  
installation slot, aligning the module with installation  
guides, and secure using the front panel fastener  
screw. NOTE: Ensure that module is firmly seated  
against the backplane.  
10T/2 SPECIFICATIONS:  
For help with this product, contact our Technical Support:  
The operating description in this Instruction Manual is  
for use by qualified personnel only. To avoid electrical  
shock, do not perform any servicing of this unit other  
than that contained in the operating instructions, unless  
you are qualified and certified to do so by Omnitron  
Systems Technology, Inc.  
Model Type  
Protocols  
10T/2  
Phone:  
Fax:  
(949) 250-6510  
(949) 250-6514  
10BASE-T and 10BASE-2  
RJ-45 and BNC  
Address: Omnitron Systems Technology, Inc.  
140 Technology Dr., #500  
Connectors  
Coax Termination,  
Backplane Enables  
Irvine, CA 92618 USA  
Controls  
Warranty  
Email:  
URL:  
2. Secure module by securing panel fastener screw  
(attached to module) to chassis front.  
This product is warranted to the original purchaser  
against defects in material and workmanship for a  
period of 2 YEARS from the date of shipment. A  
LIFETIME limited warranty may be obtained by the  
original purchaser by REGISTERING this product with  
Omnitron within 90 days from the date of shipment. To  
register, complete and mail or fax the enclosed  
Registration Card to the indicated address. You may  
also register your product on the internet at  
warranty period, Omnitron will, at its option, repair or  
replace a product which is proven to be defective.  
Power, Coax Collision,  
Coax Activity, UTP Link/Activity  
No other warranty is expressed or implied. Omnitron  
specifically disclaims the implied warranties of  
merchantability and fitness for any particular purpose.  
LED Displays  
3. Attach the iConverter 10T/2 RJ45 connector via a  
category 5 cable to a 10Base-T Ethernet device.  
Dimensions  
Weight  
W:0.85" x D:4.5" x H:2.8"  
8 oz.  
Exclusive Remedies  
4. Attach the iConverter 10T/2, via a coax cable to a  
10BASE-2 Ethernet device.  
The remedies provided herein are the Buyer’s sole and  
exclusive remedies. Omnitron shall not be liable for  
any direct, indirect, special, incidental, or consequential  
damages, whether based on contract, tort, or any legal  
theory.  
Compliance  
UL, CE, FCC Class A  
5. If using the iConverter 10T/2 at the end of a coaxial  
network, set Coax Termination “T-IN” DIP-Switch to  
the “ON” position.  
Power  
Requirement  
1.0A @ 3.3VDC (typical)  
Standard: 0 to 50º C  
Wide: -40 to 60º C  
Storage: -40 to 80º C  
LED INDICATORS:  
Temperature  
LED  
Color Description  
For warranty service, the product must be sent to an  
Omnitron designated facility, at Buyer’s expense.  
Omnitron will pay the shipping charge to return the  
product to Buyer’s designated US address (within the  
48 contiguous states and the District of Columbia)  
using Omnitron’s standard shipping method.  
Pwr:  
Col:  
Act:  
Lk/Act:  
Yellow On - Power on  
Yellow On - Coax collision  
Green On - Coax activity  
Green On - UTP link  
Blink - UTP activity  
Humidity  
Altitude  
5 to 95% (non-condensing)  
-100m to 4000m  
722,000  
MTBF (hrs)  
Limitation of Warranty  
The foregoing warranty shall not apply to defects  
resulting from improper or inadequate use and/or  
Form: 040-08340-001D 9/07  
Page 10  
Page 6  
Page 7  
Page 8  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  

NAD Blu ray Player T587 User Manual
NETGEAR Network Router WGE101 User Manual
New Balance Headphones NB439 User Manual
Niles Audio Calculator HD83 User Manual
Nokia Tablet 2520 User Manual
Nortel Networks Server NN43001 301 User Manual
Nortel Networks Switch Optivity Switch User Manual
Omnimount Computer Accessories WS 3 User Manual
Panasonic Cordless Telephone kx tcd725em User Manual
Panasonic Digital Camera BB HCE481 User Manual