|
OMEGA
OS643W
Infrared Thermometer
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This instrument is a portable easy use 3½ digit, compact-sized digital
thermometer designed to use infrared or K-type thermocouple as input. Meter
with Backlit LCD, Auto-hold function and auto power off (15 seconds approx.)
feature after releasing MEAS button to extend battery life and with analog signal
output function. Temperature indication follows Reference Temperature/Voltage
Tables N.I.S.T. Monograph 175 Revised to ITS-90 for K-type thermocouple.
SAFETY INFORMATION
It is recommended that you read the safety and operation instructions before
using the thermometer.
WARNING
To avoid electrical shock, do not use this instrument when voltages
at the measurement surface exceed 24V AC or DC.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
To avoid damage or burns, do not make temperature measurement
in microwave ovens.
The
symbol on the instrument indicates that the operator must refer to an
explanation in this manual.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
• Do not use the unit near any device which generates strong electromag-
netic radiation or near a static electrical charge, as these may cause errors.
• Do not point the lens at the sun or at any other source of strong light. If you
do, the sensor may be damaged.
• Do not contact the lens against the object whose temperature is to be
measured, or get it dirty, allow it to be scratched, or allow any foreign
material to adhere to it. Doing so may cause errors.
• Do not touch or hold by the front cone. Temperature reading can be affected
by heat from hand.
• Do not place the meter on or around hot objects (70°C/158°F). It may cause
damage to the case.
• If the meter is exposed to significant changes in ambient temperature (hot
to cold or cold to hot). Allow 20 minutes for temperature stabilization, before
taking measurement.
• Condensation may form on the lens when going from a cold to hot
environment-wait 10 minutes for conden sation to dissipate befor taking
measurements.
• This unit is not constructed to be water proof or dustproof, so do not use it
in a very dusty environment or in one where it will get wet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
GENERAL
Display: 3½ digit liquid crystal display (LCD) with maximum reading of 1999.
Overrange: (OL) or (-OL) is displayed.
Low battery indication: the "
" is displayed when the battery voltage drops
below the operating level.
Measurement rate: 2.5 times per second, nominal.
Operating Environment: 32°F to 122°F (0°C to 50°C) at < 70% relative
humidity.
Storage Temperature: 40°F to 140°F (-20°C to 60°C), 0 to 80% R.H. with battery
removed from meter.
Auto power off: 15 seconds approx.
Standby consume current: <1µA.
Battery: 4 pcs 1.5V (AAA size).
Battery Life: 100 hours (continuity) typical (Back-Light not illuminated).
Dimensions: 170mm(H) x 44mm(W) x 40mm(D).
Weight: 160g including batteries.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Infrared Radiation ELECTRICAL
Temperature Range: 0°F to 500°F, -20°C to 260°C.
Display Resolution: 1°F / 1°C.
Accuracy: ±3% of reading or ±6°F/3°C, whichever is greater @ 64.4 to 82.4°F
(@ 18 to 28°C) ambient operating temperature.
Temperature Coefficient: ±0.2% of reading or ±0.36°F/0.2°C, whichever is
greater, change in accuracy per °F/°C change in ambient operating tempera-
ture above 82.4°F/28°C or below 64.4°F/18°C.
Response Time: 1 second.
Spectral Response: 6 to 14µm nominal.
Emissivity: Pre-set 0.95.
Analog Output: 1mV/°F(°C).
Detection Element: Thermopile.
Optical Lens: Fresnal Lens.
Field of View: 65mmØ at 1000mm.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Spot size increases with distance from the probe tip as shown
6
Download from Www.Somanuals.com. All Manuals Search And Download.
K-type thermocouple ELECTRICAL
Temperature Range: -58°F to 1999°F, -50°C to 1300°C.
Display Resolution: 1°F / 1°C.
Accuracy: Accuracy is specified for operating temperatures over the range of
64°F to 83°F (18°C to 28°C), for 1 year, not including thermocouple error.
±(0.3% rdg + 2°F) -58°F to 1999°F
±(0.3% rdg + 1°C) -50°C to 1000°C
±(0.5% rdg + 1°C) 1000°C to 1300°C
Temperature Coefficient: 0.1 times the applicable accuracy specification per
°C from 32°F to 64°F and 83°F to 122°F (0°C to 18°C and 28°C to 50°C).
Input Protection: 24V dc or 24V ac rms maximum input voltage on any
combination of input pins.
Input Connector: Accepts standard miniature thermocouple connectors (flat
blades spaced 7.9mm, center to center).
Analog Output: 1mV/°F(°C).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
MEAS (MEASURE) Button
Depress MEAS button to turn on the meter for measuring temperature. Releasing
MEAS button to stop measuring temperature and automatically hold the display
reading, the meter turns off automatically after 15 seconds.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Infrared Radiation Measurements
1. When the power is off, pressing the MEAS button turns on the power.
2. Use "IR / K" switch to select IR Temperature function.
3. Use " " switch to turn on or turn off the display Back-Light.
4. Use "°F/°C" switch to select °F or °C the Temperature Range.
5. Point the lens at the object whose temperature is to be measured.
6. Press the MEAS button. Measurement is performed as long as the MEAS
button is kept pressed.
7. Referring to the spot size figure.
NOTE: Although the field of measurement (or Field of View) and the spot
almost coincide, actually the field of measurement corresponds to the
diameter for 90% optical response. The object whose temperature is to be
measured needs to be larger than the measurement diameter (spot of size)
by an adequate margin at least 1.5 to 2 times larger.
8. Read the display.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
K-type thermocouple Measurements
1. When the power is off, pressing the MEAS button turns on the power.
2. Use "IR / K" switch to select K Temperature function.
3. Use " " switch to turn on or turn off the display Back-Light.
4. Use "°F/°C" switch to select °F or °C the Temperature Range.
5. Connect a type K thermocouple to the jack on the instrument. Place the probe
or thermocouple tip on or in the material to be measured.
6. Press the MEAS button. Measurement is performed as long as the MEAS
button is kept pressed.
7. Read the display.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MEASUREMENT CONSIDERATIONS
1. Theory of Measurement
Every object emits infrared energy in accordance with its temperature. By
measuring the amount of this radiant energy, it is possible to determine the
temperature of the emitting object.
2. About Infrared
Infrared radiation is a form of energy (electromagnetic radiation), and has the
property that it passes easily through air while it is easily absorbed by solid
matter. With an emission thermometer, which operates by detecting infrared
radiation accurate measurement is possible, irrespective of the air tempera-
ture or the measurement distance.
3. Emission Thermometer Structure
Infrared radiation which has been emitted from the object is focused upon an
infrared radiation sensor, via an optical system. This includes a lens which is
transparent to infrared radiation, and a 5.3µm cut off filter. The output signal
from the infrared radiation sensor is input to an electronic circuit along with the
output signal from a standard temperature sensor (Thermopile).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Emissivity
All objects emit invisible infrared energy. The amount of energy emitted is
proportional to the object's temperature and its ability to emit IR energy. This
ability, called emissivity, is based upon the material that the object is made of
and its surface finish. Emissivity values range from 0.10 for a very reflective
object to 1.00 for a black body. Factory set emissivity value of 0.95, which
cover 90% of typical applications.
5. If the surface to the measured is covered by frost or other material, clean it to
expose the surface.
6. If the surface to be measured is highly reflective, apply masking tape or matt
finish black paint to the surface.
7. If the meter seems to be giving incorrect readings check the front cone. There
may be condensation or debris obstructing the sensor; clean per instructions
in the maintenance section.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery Replacement
Powerissuppliedbyfour1.5V(AAAsize)batteries. The" "appearsontheLCD
display when replacement is needed. To replace the batteries, remove the screw
from the back of the meter and lift off the battery cover case. Remove the
batteries from battery contacts.
Cleaning
Periodically wipe the case with a damp cloth and detergent, do not use abrasives
or solvents.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Substance
Thermal
emissivity
Substance
Thermal
emissivity
Asphalt
Concrete
Cement
Sand
0.90 to 0.98
0.94
0.96
Cloth (black)
Human skin
Lather
0.98
0.98
0.75 to 0.80
0.90
Charcoal (powder) 0.96
Earth
Water
Ice
Snow
0.92 to 0.96
0.92 to 0.96
0.96 to 0.98
0.83
0.90 to 0.95
0.90 to 0.94
0.94
0.80 to 0.90
0.89 to 0.91
0.93 to 0.96
Lacquer
0.80 to 0.95
0.97
0.94
0.85 to 0.95
0.90
Lacquer (matt)
Rubber (black)
Plastic
Timber
Paper
Glass
Ceramic
Marble
Plaster
Mortar
Brick (red)
0.70 to 0.94
chromium oxides 0.81
Copper oxides
lron oxides
Textiles
0.78
0.78 to 0.82
0.90
14
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
OMEGA warrants this unit to be free of defects in materials and workmanship and to give satisfactory service for a
period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the
normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA's customers
receive maximum coverage on each product. If the unit should malfunction, it must be returned to the factory for
evaluation. OMEGA's Customer Service Department will issue an Authorized Return (AR) number immediately
upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be repaired or
replaced at no charge. However, this WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of being damaged as a result of excessive corrosion; or current, heat moisture or vibration;
improper specification;misapplication;misuse or other operating conditions outside of OMEGA's control.Components
which wear or which are damaged by misuse are not warranted. This includes contact points, fuses, and triacs.
OMEGA is glad to offer suggestions on the of use of its various products. Nevertheless, OMEGA only warrants
that the parts manufactured by it will be as specified and free of defects
OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER,
EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED.
LIMITATION OF LIABILITY:The remedies of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract warranty, negligence, indemnification, strict
liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In
no event shall OMEGA be liable for consequential, incidental or special damages.
Every precaution for accuracy has been taken in the preparation of this manual; however, OMEGA ENGINEERING,
INC.neither assumes responsibility for any omissions or errors that may appear nor assumes liability for any damages
that result from the use of the products in accordance with the information contained in the manual.
SPECIAL CONDITION: Should this equipment be used in or with any nuclear installation or activity, purchaser will
indemnity OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
equipment in such a manner.
Download from Www.Somanuals.com. All Manuals Search And Download.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is
constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no
liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected application.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.BEFORE RETURNING
ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM
OMEGA'S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned
AR number should then be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in
transit.
FOR WARRANTY RETURNS, please have the following FOR NON-WARRANTY REPAIRS, consult OMEGA for
information available BEFORE contacting OMEGA:
1. P.O. number under which the product was
PURCHASED.
2. Model and serial number of the product under
warranty, and
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1. P.O. number to cover the COST of the repair.
2. Model and serial number of product , and
3. Repair instructions and/or specific problems relative
to the product.
3. Repair instructions and/or specific problems relative
to the product.
OMEGA's policy is to make running changes, not model changes, whenever an improvement is possible. This
affords our customers the latest in technology and engineering. OMEGA is a registered trademark of OMEGA
ENGINEERING, INC. © Copyright 1999 OMEGA ENGINEERING, INC. All rights reserved. This document may not
be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable from, in
whole or in part, without prior written consent of OMEGA ENGINEERING, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
Whe re Do I Find Eve rything I Ne e d for
Proc e ss Me a sure m e nt a nd Control?
OMEGA...Of Course !
HEATERS
TEMPERATURE
p H/ CONDUCTIVITY
þ Heating Cable
þ
Thermocouple, RTD & Thermistor
Probes, Connectors, Panels &
Assemblies
þ pH Electrodes, Testers &
Accessories
þ Benchtop/Laboratory Meters
þ Controllers, Calibrators,
Simulators & Pumps
þ Cartridge & Strip Heaters
þ Immersion & Band Heaters
þ Flexible Heaters
þ Wire: Thermocouple, RTD &
þ Laboratory Heaters
Thermistor
þ
þ
Calibrators & Ice Point References
Recorders, Controllers & Process
Monitors
þ Industrial pH & Conductivity
Equipment
PRESSURE/ STRAIN AND FORCE
þ Transducers & Strain Gauges
þ Load Cells & Pressure Gauges
þ Displacement Transducers
þ Infrared Pyrometers
DATA ACQUISITION
þ Data Acquisition & Engineering
Software
ENVIRONMENTAL
þ Instrumentation & Accessories
þ Communications-Based
Acquisition Systems
MONITORING AND CONTROL
FLOW/ LEVEL
þ
Metering & Control Instrumentation
þ Plug-in Cards for Apple, IBM
& Compatibles
þ Datalogging Systems
þ Recorders, Printers & Plotters
þ Rotameters, Gas Mass
Flowmeters & Flow Computers
þ Air Velocity Indicators
þ Turbine/Paddlewheel Systems
þ Totalizers & Batch Controllers
þ Refractometers
þ Pumps & Tubing
þ Air, Soil & Water Monitors
þ Industrial Water & Wastewater
Treatment
þ pH, Conductivity & Dissolved
Oxygen Instruments
M-3263/0799
Download from Www.Somanuals.com. All Manuals Search And Download.
|