Digital Camera Instructions
➧Preparations
D-300L
D-200L
➧Taking pictures
➧Displaying pictures on the
LCD monitor
➧Transferring images to a
personal computer
Ⅲ Before using your camera, read this manual
carefully to ensure correct use.
➧Others
Ⅲ We recommend that you take test shots to
get accustomed to your camera before
taking important photographs.
Serial number
Digital camera
CD-ROM
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Attachments
—
Do not use attachments not
10. Ventilation — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the product and to protect from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
recommended by the product manufacturer as they may
cause hazards.
7. Water and Moisture — Do not use this product near water
— for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub; in a wet basement; or near a swimming
pool; and the like.
8. Accessories — Do not place this product on an unstable
stand, tripod, bracket, table, or cart. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a tripod, stand,
bracket. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
11. Power Sources — This product should be operated only
from the type of power source indicated on the label. If you
are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
9. A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
12. Grounding or Polarization — This product may be
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
PORTABLE CART WARNING
(Symbol provided by RETAC)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternate Warnings — This product is equipped with a three-
wire grounding-type plug, a plug having a third (grounding)
pin. This plug will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the grounding-type
plug.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION
13. Power-Cord Protection — Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
14. Protective Attachment Plug — The product is equipped
with an attachment plug having overload protection. This is
a safety feature. See Instruction Manual for replacement or
resetting of protective device. If replacement of the plug is
required, be sure the service technician has used a
replacement plug specified by the manufacturer that has
the same overload protection as the original plug.
NEC – NATIONAL ELECTRICAL CODE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Outdoor Antenna Grounding — If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. See figure “Example of antenna
grounding as per National Electrical Code, ANSI/NFPA 70”
17. Power Lines — An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
18. Overloading — Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19. Object and Liquid Entry — Never push objects of any
kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the product.
16. Lightning — For added protection for this product during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
20. Servicing — Do not attempt to service this product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Damage Requiring Service — Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
23. Safety Check — Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the
product.
24. Heat — The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that
are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
e) If the product has been dropped or damaged in any
way.
Radio and Television Interference
f) When the product exhibits a distinct change in
performance — this indicates a need for service.
● Change or modifications not expressly approved by the
manufacturer may void the user’s authority to operate this
equipment.
22. Replacement Parts — When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
This equipment has been tested and found to comply with the
limits for Class B digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
6
Download from Www.Somanuals.com. All Manuals Search And Download.
interference to radio communications. However, there is no
guarantee that interference will not occur in particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
WARNINGS
• The lithium battery must only be replaced with a lithium
battery model number CR2025 [3V]. Use of another
lithium battery may present the risk of fire or explosion.
• Keep the batteries away from children.
• If a battery is swallowed, see a doctor immediately.
• Dispose of used lithium batteries promptly, in a safe
manner that complies with all applicable laws.
• The lithium battery may present the risk of fire or chemical
burn if mishandled.
Only RS232C serial cable in the set should be connected to
the camera and a PC.
• Do not recharge, disassemble, heat above 100°C (212
°F) or dispose of in the fire.
• Before use, wipe the battery clean with a dry soft cloth to
assure good contact.
FCC statement
This device complies with Part 15 of FCC rules. Operation
is subject to following two conditions:
• Never use metallic tweezers to hold the battery, and
never short circuit the (+) and (–) sides of the battery.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Legal and other notices
Windows is a trademark of Microsoft Corporation.
Macintosh is a registered trademark of Apple Computer
Inc.
● All contents of this publication are subject to change
without notice.
All other brand names and product names are
registered.
● Although the contents of this publication have been
carefully checked to avoid errors, some may still
occur. If you are in doubt about any points or find
mistakes or omissions, please contact us.
● No part of this publication may be reproduced or
reprinted except for personal use without the prior
permission of Olympus.
● Olympus makes no representations or warranties
regarding any damages, or benefit expected by using
this unit lawfully, or any request from a third person,
which are caused by the inappropriate use of this unit.
● Olympus makes no representations or warranties
regarding any damages or any benefit expected by
using this unit lawfully which are caused by erasing
the picture data.
● The quality of the picture taken with this camera is
different from the quality of a picture taken with a
conventional compact camera.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR SAFE USE
Thank you for purchasing the Olympus digital
camera. Before you start to use your new camera,
please read these instructions carefully to obtain
optimum performance and a longer service life from
the unit. Be sure to retain this manual for future
reference.
WARNINGS
1.NEVER TRY TO USE THE FLASH WHEN TAKING
PICTURES OF PEOPLE (ESPECIALLY INFANTS) AT
CLOSE RANGE. THE CAMERA’S FLASH MAY DAMAGE
THE SUBJECT’S EYES AT CLOSE RANGE. DO NOT
TAKE PICTURES OF CHILDREN FROM A DISTANCE OF
LESS THAN ONE METER (ABOUT THREE FEET).
2.DO NOT AIM YOUR CAMERA DIRECTLY AT THE SUN
OR OTHER EXTREMELY BRIGHT SUBJECTS. DOING
SO MAY DAMAGE YOUR EYES.
Warning: Ignoring this Warning mark and
operating this product incorrectly may
lead to serious injury or death.
3.DO NOT USE THIS CAMERA IN THE VICINITY OF
FLAMMABLE OR EXPLOSIVE GAS.
Caution: Ignoring this Caution mark and
operating this product incorrectly
may lead to injury.
4.DO NOT LEAVE THIS CAMERA WITHIN THE REACH OF
INFANTS OR CHILDREN.
• THE CHILD MIGHT PUT THE STRAP AROUND HIS OR
HER NECK. THIS COULD CAUSE STRANGULATION
OR CHOKING.
• THE CHILD MIGHT SWALLOW BATTERIES OR
SMALL ATTACHMENTS. IF THIS HAPPENS,
CONTACT A PHYSICIAN IMMEDIATELY.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
• THE CHILD MIGHT ACTIVATE THE FLASH FROM TOO
CLOSE AND CAUSE DAMAGE TO HIS OR HER EYES.
6.DO NOT STORE THE CAMERA IN HUMID OR DUSTY
PLACES. THIS MAY CAUSE FIRE OR ELECTRIC SHOCK
• THE CHILD MIGHT DAMAGE THE CAMERA.
7.DO NOT COVER THE FLASH WITH YOUR HAND
DURING OPERATION. DO NOT TOUCH THE FLASH
AFTER FIRING IT CONTINUOUSLY. YOU MAY GET
BURNED.
5.BATTERY FLUID MAY LEAK, GENERATING HEAT AND
POSSIBLY CAUSING A FIRE OR EXPLOSION.
• DO NOT USE UNSPECIFIED BATTERIES.
8.IF YOU DROP THE CAMERA IN WATER OR GET WATER
INSIDE IT, UNLOAD THE BATTERIES IMMEDIATELY
AND CONTACT YOUR NEAREST OLYMPUS SERVICE
CENTER. LEAVING BATTERIES IN A WET CAMERA
MAY CAUSE FIRE OR ELECTRIC SHOCK.
• DO NOT THROW BATTERIES INTO A FIRE, OR
EXPOSE TO HEAT.
• DO NOT DISASSEMBLE THE UNIT WITH BATTERIES
INSIDE.
• DO NOT USE NEW BATTERIES AND OLD BATTERIES
TOGETHER. DO NOT MIX DIFFERENT TYPES OF
BATTERIES OR DIFFERENT MANUFACTURERS’
BATTERIES.
• DO NOT CHARGE ALKALINE AND LITHIUM
BATTERIES. IT IS NOT POSSIBLE TO CHARGE
THESE TYPES OF BATTERIES.
• KEEP UNLOADED BATTERIES OUT OF THE REACH
OF INFANTS AND CHILDREN. IF AN INFANT OR
CHILD SWALLOWS THE BATTERIES, CONTACT A
PHYSICIAN IMMEDIATELY.
• DO NOT LOAD THE BATTERIES IN THE OPPOSITE
DIRECTION TO THAT SHOWN IN THIS
INSTRUCTIONS.
0
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
1.IF YOU NOTICE AN UNUSUAL SMELL, NOISE, OR
SMOKE EMITTING FROM THIS CAMERA, UNLOAD THE
BATTERIES CAREFULLY TO AVOID BEING BURNED.
CONTACT YOUR NEAREST OLYMPUS SERVICE
CENTER IMMEDIATELY.
2.NEVER ATTEMPT TO DISASSEMBLE THIS CAMERA. IT
CONTAINS HIGH-VOLTAGE CIRCUITRY THAT MAY
CAUSE ELECTRIC SHOCK AND INJURY.
3.UNLOAD THE BATTERIES WHEN NOT USING THE
CAMERA FOR LONG PERIODS. BATTERY HEAT
GENERATION OR FLUID LEAK MAY CAUSE A FIRE OR
INJURY.
4.DO NOT USE THE CAMERA IF THE BATTERY FLUID
HAS LEAKED. LEAKED BATTERY FLUID MAY CAUSE A
FIRE OR ELECTRIC SHOCK. CONTACT YOUR
NEAREST OLYMPUS DEALER OR OLYMPUS SERVICE
CENTER.
5.DO NOT OPERATE THE CAMERA WITH WET HANDS.
AS YOU MAY GET AN ELECTRIC SHOCK.
6.DO NOT STORE THE CAMERA IN ANY PLACE
EXPOSED TO EXCESSIVE HEAT. THIS MAY WEAKEN
THE PARTS OR CAUSE A FIRE.
!
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND STORAGE
BATTERY HANDLING
HANDLING
Ⅲ This camera is built with precision electric parts. To avoid
malfunctioons or mechanical problems, do not use or store the
camera in the following places:
• Places exposed to direct sunlight (a beach in summer, for
example).
• Places exposed to excessive heat, humidity, or extreme
variations of temperature and humidity.
• Places exposed to sand or dust.
• Near a fire.
Ⅲ This camera uses four AA alkaline batteries. AA NiCd batteries
or AA nickel hydrocloride batteries or AA lithium batteries can
also be used, but the battery check function will not function
correctly.
Ⅲ Do not use 3 V manganese batteries. Besides shortening
battery life, manganese batteries may overheat and damage
the camera.
Ⅲ Use the batteries correctly. Incorrect use of batteries can cause
fluid leak, heat generation, or other damage. When replacing
batteries, be sure to load them correctly.
Ⅲ The batteries may be temporarily disabled when exposed to
cold temperatures. Try to keep the camera and batteries warm
when using the camera in a cold environment. Batteries that
are weak in cold temperatures will be restored under normal
temperatures.
Ⅲ Sweat, oil, and so on, can prevent a battery’s terminals from
making electrical contact. To avoid this, wipe both terminals
before loading battery.
Ⅲ Keep spare batteries on hand when going on a long trip. New
batteries may be difficult or impossible to obtain abroad.
Ⅲ When you use NiCd batteries and nickel hydrocloride batteries,
make sure they have all been fully charged in the same battery
charger.
• Near any volatile materials.
• Near a heater, cooler, or humidifier.
• Places exposed to excessive moisture.
• Places exposed to vibrations.
• Inside a car.
• Near magnetic field.
Ⅲ Do not shake or shock the camera.
Ⅲ Do not leave the camera with its lens pointing towards direct
sunlight. This will damage the lens.
Ⅲ Do not leave the camera unused for a long period of time. This
may cause battery leakage. In addition this can lead to problems
including the growth of mold in the camera. Before using the
camera, press the shutter release button to check operation.
Ⅲ Do not turn the camera when it is mounted on a tripod.
Ⅲ Do not touch any of the camera’s internal parts.
Ⅲ Use NiCd batteries and nickel hydrocloride batteries only after
having carefully read the instructions accompanying them.
Ⅲ Do not use the flash for extended periods as this can cause the
flash to become excessively hot. Do not touch the flash when it
is hot.
@
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECK THE CONTENTS
Camera
Strap
Instructions
Warranty card
User’s card
Windows / Macintosh package includes:
• 232C PC serial cable
AA alkaline
• Conversion connector for Windows
• Conversion connector for Macintosh
• CD-ROM software for Macintosh & Windows
• 3.5" floppy disk software
batteries
(4 pieces)
Lithium battery
(CR2025 x 1 piece)
(for Windows 95 / Windows 3.1)
• 3.5" floppy disk software for Macintosh
Option
• AC adaptor
#
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN FEATURES
Ⅲ Portable, battery-powered, lightweight, compact design.
Ⅲ In addition to an optical viewfinder, an LCD monitor is provided for more flexibility when
composing shots and viewing image.
Ⅲ The highest performance wide-angle lens in its class, offers you the same ease of use as a
conventional compact camera.
Ⅲ 810,000-pixel CCD delivers the highest quality pictures in its class. (D-300L only)
➧ “Make sure” indicates items to be double checked.
➧ “Note” indicates other information you should be aware of.
➧ Actual product may differ slightly from that shown in illustrations.
$
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
PREPARATIONS
DISPLAYING PICTURES ON THE LCD
MONITOR
Names and functions of parts ................................................16
Using the strap.......................................................................18
Loading the batteries..............................................................19
Loading the lithium battery.....................................................19
Turning on and checking the batteries...................................20
Checking the number of remaining pictures...........................21
Points to remember................................................................22
Turning on the LCD monitor...................................................35
Displaying pictures.................................................................36
Protection...............................................................................36
Erasing pictures .....................................................................37
Slide-Show mode...................................................................39
Multi-Display mode.................................................................39
Adjusting the date and time....................................................40
TAKING PICTURES
TRANSFERRING IMAGES TO A PERSONAL
COMPUTER
Personal computer environment ............................................41
Installing provided software....................................................42
Connecting to a personal computer .......................................44
Using the household power supply (Optional) .......................45
System chart ..........................................................................46
Taking pictures.......................................................................24
Using the focus lock (D-300L only) ........................................27
Autofocus (D-300L only) ........................................................28
Selecting the resolution..........................................................29
Using the flash modes............................................................30
Auto-Flash...........................................................................31
Red-Eye Reducing Flash ...............................................31
Off (flash override)..........................................................32
Fill-In Flash (forced activation) .......................................32
Macro mode ...........................................................................33
Working range........................................................................33
Self-timer................................................................................34
Setting the beep sound ..........................................................34
OTHERS
Questions and answers..........................................................47
Troubleshooting .....................................................................48
Notes on display backlights....................................................52
Specifications.........................................................................53
%
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATIONS
NAMES AND FUNCTIONS OF PARTS
23 4 5 6 7 8
1
$%
^
& *
(
)
9
0
!
q
@ #
^
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Unit
Close-up correction marks (p. 33)
Viewfinder Display
1 Shutter release / Erase OK button.............................P. 23
2 Flash mode button ......................................................P. 30
3 Erase mode button......................................................P. 37
4 Flash.............................................................................P. 30
5 Control panel ...............................................................P. 17
6 Self-timer / Slide-Show button ..............................P. 34/39
7 Macro mode / Protect mode button......................P. 33/36
8 Resolution selection / Multi-Display button.........P. 29/39
9 Self-timer signal ..........................................................P. 34
0 Lens
Autofocus mark* /
Backlighting correction
mark (p. 27/31)
Green lamp
* Autofocus available only with D-300L.
Control Panel / LCD monitor
•Control Panel Icons
! Lens cover ...................................................................P. 20
@ Computer terminal ......................................................P. 44
# DC input terminal ........................................................P. 45
$ Viewfinder ....................................................................P. 17
% Green lamp...................................................................P. 17
^ LCD monitor.................................................................P. 17
& LCD monitor ON/OFF/PLAY button ......................P. 26/35
* Previous (–) / Next (+) button ................................P. 36/39
( Lithium battery compartment cover..........................P. 19
) Tripod thread ...............................................................P. 34
q Battery compartment cover........................................P. 19
Write Erase
Battery check
Resolution
Macro
Number of
remaining
pictures
Self-timer Flash mode
•LCD Monitor Icons
Resolution
Battery check
Protect mark
Date / Time
’96 03 21
10:35
Frame
number
15
&
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE STRAP
Caution:
1
2
◆ Attach the strap correctly as shown on the left so
that the camera does not fall off. If the strap is
attached incorrectly and the camera comes loose
and falls off, Olympus is not responsible for any
damage.
3
*
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING THE BATTERIES
LOADING THE LITHIUM
BATTERY
Use four AA alkaline batteries, four AA NiCd batteries, four AA nickel
hydoride batteries or four AA Lithium batteries. Manganese battery
cannot be used.
Use a pointed
instrument such
as a ballpoint pen
Read “Battery Handling” on Page 12.
to
open
the
lithium battery
c o m p a r t m e n t
cover. Load the
2
lithium battery as
shown and then close the cover until you hear it click
into place.
1
Cautions:
◆ Be sure to insert the batteries as directed.
1 Slide the battery compart-
ment cover to the left 1and
pull the lid upward 2.
2 Insert the new batteries
correctly as shown and close
the battery compartment
cover tightly.
◆ Do not use manganese batteries. Besides
shortening battery life, manganese batteries may
overheat and damage the camera. Use only the
types of batteries specified in this manual.
◆ Keep the lithium battery and lithium battery holder
out of the reach of children. If a child swallows the
battery or cover, contact a doctor immediately.
◆ Do not put any foreign substances such as metal
in the camera. Doing so damage the camera.
<Make sure>
➧
The lens barrier is closed
and the camera is turned
off before loading the
batteries.
(
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING ON THE CAMERA AND CHECKING THE BATTERY
To turn on the camera, slide open the lens cover as shown. Remaining battery power and remaining pictures are indicated on the
control panel.
When you turn on the power, battery status is indicated as
below.
Display
Meaning
lights and turns off
automatically.
Batteries are OK.
You can shoot.
blinks and other
indicators on the control
panel are displayed
normally.
Battery power is low and
batteries should be replaced.
blinks and other
indicators on the control
panel go out.
Batteries are dead and
should be replaced
immediately.
<Make sure>
➧ If you do not operate the camera for three minutes, the
power save function activates and the power turns off
automatically.
➧ To turn on again, close and open the lens cover or
depress the shutter release button halfway.
Note:
◆ Keep spare batteries on hand when going on a long
trip or to a wedding for example, or when using the
camera in cold weather.
)
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE NUMBER OF REMAINING PICTURES
When the number of remaining pictures is 0, the camera
●
emits a long single beep and the green lamp blinks. If the
memory is full, the camera beeps whenever the lens cover
is opened.
When the number of remaining pictures is less than 3 in the
Standard Quality mode, shooting is not possible in the High
Quality mode. (See Page 29.)
●
When you turn on the power, the number of remaining
pictures is shown on the control panel.
<Make sure>
● Maximum number of storage pictures
➧ The number of remaining pictures varies depending on
the Resolution setting. For example, if the remaining
count is 4 in the Standard Quality mode, it will be 1 in the
High Quality mode.
D-300L
30
D-200L
20
High Quality mode
Standard Quality mode
120
80
➧ We recommend that you download the pictures you’ve
already taken to a personal computer as soon as
possible (see Page 42), and erase pictures stored in the
camera on a regular basis (see Page 37).
Note:
◆ After checking the number of remaining pictures, be
sure to set and adjust the date and time by
connecting the camera to a computer.
q
Download from Www.Somanuals.com. All Manuals Search And Download.
POINTS TO REMEMBER
Correct.
Correct.
Incorrect.
<Make sure>
Note:
➧ Hold the camera firmly with both hands while keeping
elbows at sides to prevent the camera from shaking.
➧ When holding the camera vertically, hold the camera
with its flash positioned at the top.
◆ Keep your fingers and the strap away from the lens
and flash.
w
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
Proper Shutter Release
◆ Press the shutter release
button gently.
Avoid shaking the camera
when pressing the shutter
release button to prevent blurry
pictures.
1 Depress the shutter release button
2 Depress the shutter release button
fully to release the shutter, and take
the picture.
halfway.
<Make sure>
<Make sure>
➧ The green lamp next to the
viewfinder lights.
➧ The Writing indicator on the
control panel blinks, and the green
lamp next to the viewfinder blinks.
➧ The exposure will be locked.
➧ With the D-300L, the focus will be
adjusted.
e
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING PICTURES
TAKING PICTURES
Taking pictures using the optical viewfinder
1 Compose the picture using the optical viewfinder.
2 Depress the shutter release button halfway. The green
lamp lights.
3 Depress the shutter release button fully to take the picture.
4 The camera emits two short beeps to indicate that the shot
has been taken.
Caution:
5 When the Writing indicator on the control panel or the
green lamp next to the viewfinder stops blinking, the
camera is ready to take next picture. (The Writing indicator
will disappear after about 6 seconds in the High Quality
mode and in about 2 seconds in the Standard Quality
mode.)
◆ Do not unload the batteries while the Writing
indicator is blinking. Not only will the picture you
have just taken be lost, but stored pictures may also
be damaged.
r
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
◆ It is also possible to take pictures using the LCD
monitor as a viewfinder. However, it is better to use
the optical viewfinder since the camera is less likely
to shake and pictures are easier to take. Refer to
Page 26 for details on taking pictures using the LCD
monitor.
Whenever the Writing indicator is blinking, it means that the
camera is still processing the image. If you press the shutter
release button while the indicator is blinking, the shutter
won’t release.
Ⅲ
6 When you close the lens barrier, all control panel
indications disappear and the power turns off.
Ⅲ Even after turning off the power or replacing the
batteries, pictures remain stored in memory.
Note:
◆ When the camera is being operated on battery power
and the batteries are running low, the camera may
emit several short beeps and blink the number of
remaining pictures on the control panel after you take
a shot. If this happens, the picture you have just taken
may not turn out properly. Replace the batteries and
take your picture again.
t
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking pictures using the LCD monitor
1 Open the lens barrier. Press and hold the LCD monitor
2 Aim the camera by looking at the subject through the LCD
ON/OFF (green) button to turn on the LCD monitor's display.
monitor.
Note:
◆ Pictures that appear on the LCD monitor are for
composition purposes only — regardless of whether it
is used as a viewfinder or a display monitor. They do
not show such information as focus or exposure. If you
need to know this information, transfer pictures to your
computer’s display monitor.
Caution:
<Make sure>
➧ Take the picture in the same way as you would when using
the optical viewfinder. (See Page 24.)
➧ When using the LCD monitor, keep the LCD monitor
ON/OFF (green) button pressed while taking pictures.
◆ Do not touch the surface of the LCD monitor. This can
leave a blur on the monitor. Pushing too hard on the
monitor may break it.
y
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FOCUS LOCK (D-300L ONLY)
The D-300L features a convenient autofocus function. If your main subject is not within the autofocus marks, use the procedure
below to obtain focus. This is called focus lock.
Autofocus marks
1 Position your subject within the autofocus marks and press
2 Reposition your subjects in the picture frame while keeping
the shutter release button depressed halfway. Then press
the shutter release button fully.
the shutter release button halfway.
<Make sure>
Note:
●When the focus is locked, the exposure is also locked (AE
lock).
➧ The green lamp next to the viewfinder lights.
u
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOFOCUS (D-300L ONLY)
Although the D-300L’s autofocus can lock on virtually any subject, there are certain conditions, such as 1 ~ 3 shown below, where
it may not be possible to obtain the correct focus. In the situations shown below in 4 ~ 5, autofocus may not lock on the correct
subject even though the green lamp lights and the shutter releases.
2
3
4
5
1
Subjects with low
contrast
Subjects that do
not contain vertical
lines
Subjects in
excessively bright
light
Two subjects at
different distance
High-speed
subjects at close
range
Use the focus lock by
first focusing on
something at the
same distance as the
subject you wish to
take a picture of, and
then aim at the
subject.
Use the focus lock
first while holding the
camera vertically.
Then switch the
Use the focus lock by
first focusing on
something at the
same distance as the
subject you wish to
take a picture of, and
then aim at the
subject.
When the subject
looks out-of-focus
even though the
green lamp lights,
focus on another
subject at the desired
camera-to-subject
distance first. Then
recompose the frame
to take the picture.
Focus on another
subject at the desired
camera-to-subject
distance first. Then
recompose the frame
to take the picture.
Ⅲ
Ⅲ
Ⅲ
Ⅲ
Ⅲ
camera
to
the
horizontal position to
take the photograph.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING THE RESOLUTION
When using the High Quality mode
(
is indicated on the control panel.)
1024 x 768 pixels (D-300L)
640 x 480 pixels (D-200L)
When using the Standard Quality mode
(No indication on the control panel)
512 x 384 pixels (D-300L)
320 x 240 pixels (D-200L)
<Make sure>
This camera has two levels of resolution — the High Quality
mode and the Standard Quality mode.
➧ The selected resolution mode remains the same even
when the camera is switched off. The mode returns to
High Quality or Standard Quality when the batteries are
replaced.
Press the Resolution selection button to choose either mode.
➧ The number of remaining frames varies according to the
resolution mode. In the Standard Quality mode, four
times as many pictures can be taken as in the High
Quality mode.
o
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE FLASH MODES
This camera has four flash modes. Select the flash mode
according to your shooting conditions and needs.
(No icon) AUTO-FLASH mode
Automatically fires in low-light and backlight
conditions. (p. 31)
➟
How to select the flash mode:
As you press the Flash mode button, the mode switches as
shown on the right. The selected flash mode is displayed on
the control panel.
RED-EYE REDUCING FLASH mode
Significantly reduces the phenomenon of
“red-eye” (when a subject’s eyes appear red in
flash photos). (p. 31)
OFF mode
The flash does not fire. (p. 32)
FILL-IN FLASH mode
Fires regardless of available light. (p. 32)
OK
Flash Working Range
D-300L
D-200L
0.2 m ~ 2.4 m (0.65 ~ 7.9 ft.)
0.2 m ~ 3.5 m (0.65 ~ 11.5 ft.)
Note:
When the green lamp is blinking, it means the flash is being recharged. The shutter won’t release while the flash is recharging, so remove
your finger from the shutter release button and wait for several seconds.
The Red-Eye Reducing Flash mode is not canceled when the power is turned off. If any other mode is set, the camera returns to the Auto-
Flash mode.
p
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO-FLASH
RED-EYE REDUCING FLASH
In the Auto-Flash mode, the
Significantly reduces the phenomenon of “red-eye”
flash will fire automatically in
low-light and backlight
conditions.
(when a subject’s eyes appear red in flash photography).
In the Red-Eye Reducing Flash mode, the camera will emit a series of
low-power pre-flashes before the regular flash. This makes the subject’s
pupils contract, significantly reducing red-eye. Except for the pre-
flashes, this mode is the same as the Auto-Flash mode.
Notes:
◆ Be sure to hold the camera still until the shutter releases.
This takes about one second.
◆ Red-eye reduction may not be effective when the subject:
• Is not looking at the flash from the front.
• Is not watching the pre-flashes.
Backlighting
correction mark
• Is too far from the camera.
• Does not respond to the pre-flashes due to particular
individual characteristics.
• Some medications, alcohol or drugs may interfere with the
red-eye reduction process.
When you take a picture on the backlight, set the subject on the
backlighting correction marks to fire a flash.
Q
Download from Www.Somanuals.com. All Manuals Search And Download.
OFF (FLASH OVERRIDE)
FILL-INFLASH(FORCEDACTIVATION)
When you don’t want the flash to fire even in the
dark or when you want to shoot such subjects as
fireworks.
In the Off mode, the flash does not fire even in low-light
conditions. Use this mode in situations where flash
photography is not desired or is prohibited or in twilight or
night scenes.
When you want the flash to fire all the time.
In the Fill-In Flash mode, the flash fires regardless of available
light. For example, this mode can be used to brighten up a
subject’s shaded face or under artificial lighting such as back-
light, fluorescent light.
<Make sure>
Note:
◆ Since a slow shutter speed (down to 1/8 seconds) is
automatically selected in low-light situations when in
the Off mode, the use of a tripod is recommended to
prevent blurred pictures caused by camera shake.
◆ Use this mode within the flash working range (Page 30). It
may not work well under excessively bright light.
W
Download from Www.Somanuals.com. All Manuals Search And Download.
MACRO MODE
WORKING RANGE
Close-up Correction
Picture frame
Close-up correction
marks
Image area of picture at
0.2 m (0.65 ft.)
The viewfinder’s picture frame shows the area that can be shot for
subjects at . However, the picture area will move lower in the
∞
Use the Macro mode to take pictures of small subjects at
a very close distance.
A picture of an A5-size subject can be taken fully within the
frame. (Size – 4.1 x 5.8 inches)
Each time you press the Macro mode button, the mode
switches between Standard mode and Macro mode.
viewfinder as you get closer to the subject. At 0.2 m (0.65 ft.), the
shaded area is the actual available image area. In this case, the
subject should be positioned below the close-up correction marks.
Take pictures at the distance between0.2m~ (0.65 ft.~ ).
∞
∞
● Subjects closer than 0.2 m (0.65 ft.) will be out of focus and
incorrectly exposed.
● When you take pictures using the LCD monitor as a viewfinder,
the image you see is the same as what will be recorded. This
makes it easier to take close-up pictures.
Working range
Macro mode
Standard mode
Mode
D-300L
D-200L
0.2 m
(0.65 ft.)
Macro mode
0.2 m ~ 0.5 m
(0.65 ~ 1.64 ft.)
0.2 m ~ 0.75 m
(0.65 ~ 2.46 ft.)
D-300L (0.5 m / 1.64 ft.)
D-200L (0.75 m / 2.46 ft.)
Standard mode
0.5 m ~
(1.64 ft. ~
0.75 m ~
(2.46 ft. ~
∞
∞
)
)
∞
∞
∞
E
Download from Www.Somanuals.com. All Manuals Search And Download.
SELF-TIMER
SETTING THE BEEP SOUND
1 Press the Self-Timer button. The Self-Timer indicator is
displayed on the control panel.
Ⅲ Use a tripod to hold the camera securely.
2 Aim at your subject, and press the shutter release button.
How to set the beep sound
Press and hold the Flash mode button and open the lens
cover at the same time.
Ⅲ The shutter will be released about 12 seconds after the
shutter release button is pressed.
<Make sure>
• If you hear a single beep, the beep sound is set to ON.
• If the camera makes no sound, the beep sound is set to
OFF.
➧ The focus (D-300L only) and exposure lock when the
shutter release button is depressed halfway.
➧ The Self-Timer is disengaged when the shutter is
released.
<Make sure>
➧ The beep sound setting is not affected when the
batteries are unloaded.
➧ To cancel the Self-Timer after it has been activated,
press the Self-Timer button again or close the lens cover.
R
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAYING PICTURES ON THE LCD
MONITOR
TURNING ON THE LCD MONITOR
After taking a picture, you can immediately view it on the LCD monitor.
’96 03 21
10:35
3
3
Close the lens cover and press the LCD monitor ON/OFF
(green) button to turn on the LCD monitor.
● Resolution, Battery Remaining and Date indicators will
disappear after about three seconds. If the batteries are low,
the low-battery indicator appears and blinks.
● The last picture taken is displayed on the LCD monitor. The
frame number, and battery remaining indicators are also
displayed. If you set the Date, Resolution or Protection
mode while viewing pictures, these are also shown. If you
have not taken any pictures, a blank blue screen is
displayed.
● High Quality mode pictures take approximately six seconds
to come up on the LCD monitor.
T
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAYING PICTURES
PROTECTION
You can display the pictures you have
taken on the LCD monitor.
You can prevent accidental erasure of
frames you want to keep.
2
1
This function works when the lens cover is closed.
1 Display the frames and select the frame you want to keep.
2 Press the protect button to protect the selected frame.
This function works when the lens cover is closed.
1 Press the Previous (–) button to see the previous frame.
Each time you press the Previous (–) button, the preceding
frame will appear.
Ⅲ The Protect indicator appears in the upper right corner of
the LCD monitor.
3 To cancel protection, press the protect button again.
2 Press the Next (+) button to see the next frame.
Ⅲ The protected frame cannot be deleted until you press
the Protect button again.
Ⅲ Protection and its cancellation are also possible in the
Multi-Display mode (see page 39).
Ⅲ Each time you press the Next (+) button, the succeeding
frame will appear.
Ⅲ Wait until the picture is fully displayed before pressing
any buttons.
Ⅲ If similar pictures have been taken consecutively, the
LCD may not appear to change.
Y
Download from Www.Somanuals.com. All Manuals Search And Download.
ERASING PICTURES
You can delete pictures you don't want.
If the frame you want to delete is protected, you cannot start the erasing operation. Cancel the protection first before starting the
erasing operation.
OK
OK
3
YES OK 3
NO
3 Press the Erase OK (Shutter Release) button to erase the
One-Frame Erase
selected frame.
This function works when the lens cover is closed.
Ⅲ The camera makes a short single beep and the selected frame
is erased. The previous frame will now be displayed.
1 Display the frame you want to delete.
2 Press the Erase mode button until the One-Frame Erase
indicator in the upper right corner of the LCD monitor
lights.
Caution:
◆ Do not unload batteries while erasing frames as this may
Ⅲ To cancel, press the Erase mode button again.
Ⅲ Do not press the Erase mode button while an image is
being loaded onto the LCD.
result in all frames being erased.
U
Download from Www.Somanuals.com. All Manuals Search And Download.
OK
3
YES OK 3
NO
All-Frame Erase
This function works when the lens cover is
closed.
4 After several seconds all frames are erased. The blue background display will
appear on the LCD monitor.
1 Display a picture.
Ⅲ If there are any protected pictures, they will not be erased and the last-taken
protected picture will be displayed when the erasing operation is completed.
Ⅲ All-Frame Erase is also available in the Multi-Display mode. (See page 39.)
2 Press the Erase mode button and
Flash button simultaneously, the All-
Frame Erase indicator lights in the
upper right corner of the LCD monitor.
Ⅲ To cancel, press the Erase button
again.
Cautions:
3 Press the Erase OK (Shutter Release)
button to erase all frames.
◆ Be careful not to erase any pictures you don’t want to delete.
◆ Do not unload batteries while erasing frames as this may result in all
frames being erased.
Ⅲ The camera makes a short single
beep and the All-Frame Erase
indicator starts descending.
I
Download from Www.Somanuals.com. All Manuals Search And Download.
SLIDE-SHOW MODE
MULTI-DISPLAY MODE
You can run through all the pictures
automatically.
Nine frames are shown on the LCD monitor
1
4
7
2
5
8
3
6
9
5
1
2
This function works when the lens cover is closed.
This function works when the lens cover is closed.
1 Display a picture.
1 Display the picture.
2 Press the Multi-Display button. Nine frames are displayed
2 Press the Slide-Show button to start running through the
with the currently selected frame displayed in the center.
frames automatically.
3 When you press the Previous (–) button, the selected
Ⅲ The frame number and protect mark are displayed
together with the frame on the LCD monitor.
3 Press the Slide-Show button again to stop at the currently
displayed frame.
frame advances.
Ⅲ Press the Next (+) button to go backward.
4 After the frame in the upper-left corner of the display is
selected, the next six frames are displayed. (If you are
using the Next (+) button, the new frames are added when
the picture in the lower-right corner is selected.)
Ⅲ The Slide-Show mode doesn’t stop until you cancel the
operation. Press the Slide-Show button to cancel this
mode.
Ⅲ The Slide-Show is also available in the Multi-Display
mode.
5 Press the Multi-Display button to cancel the Multi-Display
mode. The currently selected frame is displayed.
O
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE DATE AND TIME
<Make sure>
◆ The date and time cannot be set directly on the
camera.
◆ Whenever you replace the lithium battery, be sure
to set the date and time again as soon as possible.
◆ We recommend that you check the date and time
before taking important photographs.
1 Connect the camera to a personal computer.
(See Page 44.)
2 Start up the bundled software.
3 Once the program has loaded, select “Camera Settings”
from the menu bar. The camera setting window appears.
4 Set the date and time as indicated in the camera settings
window.
P
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSFERRING IMAGES TO A
PERSONAL COMPUTER
PERSONAL COMPUTER ENVIRONMENT
Personal computers used with this camera
must conform to the following minimum
standards.
Personal computers used with Adobe
PhotoDeluxe™ must conform to the
following minimum standards.
● IBM PC/AT compatible
●IBM PC/AT compatible/Apple Macintosh and compatible
Operating System
: Windows 95 or 3.1
CD-ROM Drive
: More than 40 MB
: Windows 3.1—8 MB
Windows 95—16MB
: Standard RS-232C interface
D-SUB 9-pin connector
: Minimum 256 colors
Minimum 640 x 480
Operating System
: Windows 95 or 3.1
CD-ROM Drive
: MacOS™ 7.0 or higher
double speed CD-ROM Drive
Hard Disk Capacity
RAM
Hard Disk Free Space Capacity : More than 45 MB
RAM (Minimum)
Connectors
Monitor
: Windows 3.1—8 MB
Windows 95—16 MB
: 68030/40—8 MB
Power PC—16 MB
● Apple Macintosh and compatible
RAM (Recommended)
: Adobe strongly recommends
more than 16 MB of RAM. 24 to
32 MB of RAM is preferred. See
the Adobe Manual for all
requirements.
: Standard RS-232C interface
D-SUB 9-pin connector
: Minimum 256 colors
CPU
: 68030 or later
: MacOS™ 7.0 or higher
CD-ROM Drive
Operating System
Hard Disk Capacity
RAM
: More than 40 MB
: 68030/40—8 MB
Connectors
Monitor
Power PC 601/604—16 MB
: Standard RS-232C interface
D-SUB 9-pin connector
: Minimum 256 colors
Minimum 640 x 480
Connectors
Monitor
Minimum 640 x 480
a
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING PROVIDED SOFTWARE
1. Introduction
2. Installation
The Olympus digital camera’s software is distributed on a
single CD-ROM. This CD contains all the required software
for the user to download images from the camera and
manipulate them on your desktop computer. In addition, the
software provides the user with the ability to control certain
camera features and snap pictures while in a “tethered
mode.”
In order to download images from the camera or control the
camera via the computer, you will need a software
application that has either :
an Adobe PhotoShop 3.0.5 standard plug-in interface
(Macintosh™), or a TWAIN v1.6 compliant interface
(Windows™ / Windows 95™).
If you do not own such software, Olympus has supplied a
version of Adobe PhotoDeluxe. To install Adobe
PhotoDeluxe, please refer to the supplied Adobe
PhotoDeluxe documentation. Documentation is found on
the CD-ROM.
Modules are developed for the two most popular personal
computer operating systems:
MS Windows
Camera Acquisition and communications Module
Adobe PhotoDeluxe for Windows / Windows 95 CD
As mentioned, the digital camera’s acquisition and
communications software modules are structured as
standard plug-ins for popular image manipulation software
applications.
Macintosh compatible
Camera Acquisition and communications Module
Adobe PhotoDeluxe for Macintosh (CD)
For Microsoft Windows™ systems, the Olympus digital
camera’s software employs the TWAIN standard to
communicate with the camera.
Installation of the software can follow one of several scenarios :
● User do not have any image manipulation software resident
on your computer.
For Macintosh™ systems, the Olympus digital camera’s
software employs an Adobe PhotoShop compatible plug-in
module.
● User already has Adobe PhotoShop or compatible software
package installed on their computer.
s
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the plug-in software
The supplied CD-ROM contains the required installation
programs for both MS Windows and Macintosh systems.
The installation is straightforward and will require you to
answer a few questions. Installing the software is a great time
to fill out the registration card and jot down and save serial
numbers and support line phone numbers.
3. Software Notes
Several features of the camera are only accessible via the
host computer software modules, e.g., setting the camera’s
time and date, downloading images, printing images.
Please refer to the Camera Software User’s Manual in
order to learn more about these features.
d
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A PERSONAL COMPUTER
Use the appropriate connector according to the platform of your computer.
● IBM PC/AT compatible
Connect the provided computer cable
to the COM 1 or COM 2 serial port on
your computer.
● Apple Macintosh or compatible
Attach the provided conversion
connector for Macintosh to printer or
modem serial port on your computer,
and then connect the provided
computer cable.
Make sure that the camera and the computer are turned off
The enclosed Macintosh conversion
connector allows you to connect your
camera to a Macintosh computer. It
cannot be used to connect a Macintosh
to a printer.
before connecting.
1 Connect the computer cable to the computer’s serial cable
as explained on the left.
2 Open the connector cover.
3 Align the arrow mark on the computer cable plug with the
circle dot mark on the camera’s connector. Insert the plug
and push until it is in fully.
4 Open the lens barrier to turn on the power.
f
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE HOUSEHOLD POWER SUPPLY (Optional)
An optional AC adaptor allows you to power your digital
camera from the household power supply.
AC adaptor
Note:
◆ When in use for long periods, the AC adaptor will be warm
to the touch. This is normal.
House-hold
power supply
DC terminal
Warnings: Use the AC adaptor correctly and pay attention to the precautions below. Incorrect use of the AC adaptor may cause a
fire or electric shock.
◆ Use an AC120V power source.
◆ Hold the AC adaptor unit when removing it from an outlet.
◆ Never pull forcibly, bend, or twist the AC adaptor.
◆ If there are any scratches or other damage on the AC adaptor
or if there is a contact failure on the plug, consult your
nearest Olympus service center as soon as possible.
◆ When disconnecting the AC adaptor, make sure the camera
is turned off.
◆ Make sure the AC adaptor is properly plugged into the outlet.
◆ Do not connect or disconnect the AC adaptor with wet
hands.
◆ If the AC adaptor’s cord is hot, smells like smoke, or is
emitting smoke, unplug it immediately . Contact your nearest
Olympus dealer or Olympus service center.
◆ Do not use the optional exclusive AC adaptor with other
products. Olympus can not take responsibility for the
damage caused by the use of any AC adaptor other than the
one exclusively designed for this camera.
◆ If batteries are loaded in the camera, make sure the camera is
turned off before connecting or disconnecting the AC
adaptor.
◆ When you are not using the AC adaptor, be sure to unplug it.
g
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM CHART
h
OTHERS
QUESTIONS AND ANSWERS
QHow long will the batteries last?
QHow should I store the camera?
AFour new AA alkaline batteries may last for as many as 100
frames when the flash is used on half of all the shots
ACameras are susceptible to damage caused by dust,
moisture, and salt. Wipe and dry the camera thoroughly
(determined under Olympus test conditions). But this is just a
yardstick — in actual use, battery life is affected by many
variables such as the amount of LCD monitor use, the frequency
of flash use, as well as by the kind of battery used and the
environmental conditions under which the camera is used. Using
the LCD monitor frequently will use up your batteries very
quickly. Keep the LCD monitor turned off to save power.
The battery consumption figures regarding the number of
pictures the camera can take are based on our tests and our
designated batteries. These figures are for reference only. The
actual number of pictures the camera can take on a set of
batteries may vary.
before storing it. After using it at the beach, wipe it with a cloth
that has been moistened with fresh water and then wrung out.
Do not store in an area where mothballs are used. Unload the
batteries if you do not plan to use the camera for a long
period.
QWhy do the subjects’ eyes sometimes appear red in
pictures?
AThis “red-eye phenomenon” occurs with all cameras when
a flash is used. It is caused by light from the flash reflecting
off the retina at the back of the eye. Red-eye varies depending
on the individual and the shooting conditions such as ambient
lighting. Use of the Red-Eye Reducing Pre-Flash mode
significantly reduces this phenomenon.
For best results, use lithium AA batteries.
QHow can I correct the clock in the camera that will be used
to record date on the image data?
QCan I use a filter or hood?
ADate adjustment isn’t made when the camera is shipped.
After loading the lithium battery, connect the camera to a
ANo, you can’t.
personal computer and use the provided application software
to correct the date. The date also needs to be reset whenever
the AA batteries and lithium battery are replaced at the same
time.
QHow should I clean the LCD monitor?
AWipe the LCD monitor gently with lens cleaning tissue.
j
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Operating Problems
Symptom
Cause
Remedy
See
The camera
does not work.
1 The power is OFF.
1 Open the lens cover to turn on the power.
2 Reload the batteries correctly.
3 Replace the batteries with new ones.
4 Keep the batteries warm while using them.
P.20
P.19
P.19
2 The batteries are loaded incorrectly.
3 The batteries are exhausted.
4 The batteries are temporarily
unable to function.
No picture is
taken when
the shutter
release button
is pressed.
1 The flash has not finished charging
or the previous picture is being
written into memory.
1 Remove your finger from the shutter release button
P.30
P.21
and wait until the green lamp stops blinking.
2 Memory is full.
2 Check the number of remaining pictures on the
control panel and erase unnecessary frames using
the One-Frame Erase mode. Or transfer the pictures P.37
to a computer, and erase the entire memory using
the All-Frame Erase mode.
The flash doesn’t
fire.
1 The flash mode is in the Off mode.
1 Set the flash mode to something other than
P.30
the Off mode.
The pictures
1 The lens cover is left open.
1 Close the lens cover and depress the LCD monitor
ON/OFF (green button) to turn on the LCD monitor.
2 Check the number of remaining pictures.
already taken can’t
be displayed on
the LCD panel.
2 Memory is empty.
P.21
k
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Remedy
See
The LCD monitor
is hard to read.
1 Selection of brightness is wrong.
1 Connect the camera to a computer, and adjust
P.42
using the provided application software.
When the camera
is connected to a
computer, an error 3 The batteries are exhausted.
message appears
while data is being
transferred to the
computer.
1 The cable is not plugged in correctly. 1 Connect the cable correctly.
2 The power is OFF. 2 Open the lens cover to turn on the power.
P.44
P.20
P.19
P.44
3 Replace the batteries with new ones.
4 Use the operating system software to
make sure the serial port is selected correctly.
4 The serial port is not
selected correctly.
Problems with Images
Symptom
Cause
Remedy
See
The picture is
out of focus.
1 The camera moved when
the shutter button was pressed.
2 The viewfinder’s autofocus mark
was not positioned on the
subject. (D-300L only)
1 Hold the camera correctly, and press the
shutter release button.
P.22
2 Position the autofocus frame on the
P.27
subject, or use the focus lock. (D-300L only)
3 The lens is dirty.
3 Clean the lens.
l
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Remedy
See
The picture is
out of focus.
4 The mode was not selected correctly. 4 Shoot from more than the minimum working
P.33
The subject was closer than the
minimum working distance to the lens
(D-300L:0.5 m/1.64 ft;D-200L:0.75 m/
2.46 ft) with the the Normal mode
selected. Or the subject was farther
than the minimum working distance
with the Macro mode selected.
distance when in the Normal mode.
Shoot from less than the minimum working
distance when in the Macro mode.
5 The shutter release button was
pressed from right in front of the
camera in the Self-Timer mode.
5 Press the shutter release button while looking
into the viewfinder, not while standing in front of
the camera.
The picture is
too dark.
1 The flash was blocked by a finger.
1 Hold the camera correctly, keeping
your fingers away from the flash.
2 Shoot within the flash working range.
P.22
P.30
P.30
P.32
2 The subject was out of the
working range of the flash.
3 The flash mode was set to
the Off mode.
3 Check the flash mode before shooting.
4 The subject was too small
4 Set the flash to Fill-In mode.
and backlight.
;
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
Remedy
See
The picture is
too bright.
1 The flash was set to the Fill-In Flash
mode.
2 The subject was very bright.
1 Set the flash mode to one other than Fill-In Flash.
P.30
2 Point the camera to avoid overly bright subjects.
The colors of
pictures taken
indoors look
unnatural.
1 The lighting fixture(s)
1 Set the flash mode to Fill-In.
P.32
affected the picture.
The picture
has obscured
edge(s).
1 The lens was partly blocked
1 Hold the camera correctly, keeping your fingers and P.22
by a finger or the strap.
the strap away from the lens.
2 The shooting distance was too close. 2 Use the close-up compensation marks in the
P.33
viewfinder.
A
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES ON DISPLAY BACKLIGHTS
Ⅲ The fluorescent lamps used in the Control Panel and LCD
monitor have a limited service life. If either LCD monitor
begins to darken or flicker, contact your nearest service
center. (There will be a fee for this service.)
Ⅲ In cold conditions, the display backlight may be slow to
come on or may change color suddenly. To avoid this, try to
keep the camera warm when using it in cold temperatures.
Backlight performance will return to normal under normal
temperature conditions.
S
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Product type
: Digital still camera (for shooting and display)
Aperture
Photometric system
: TTL Center weighted average metering system
Exposure control : Program auto exposure
Working range
: F2.8, F5.6, F11
Recording System: Digital recording
Internal Memory : Built-in flash memory
D-300L
D-200L
: 6 MB
: 2 MB
D-300L
: 0.2 m ~ 0.5 m (0.65 ~ 1.64 ft.) (Macro mode)
No. of storable frames
0.5 m ~ ∞ (1.64 ft. ~ ∞) (Normal mode)
: 0.2 m ~ 0.75 m (0.65 ~ 2.46 ft.) (Macro mode)
0.75 m ~ ∞ (2.46 ft. ~ ∞) (Normal mode)
D-300L
: 30 pictures (High Quality mode)
D-200L
120 pictures (Standard Quality mode)
: 20 pictures (High Quality mode)
80 pictures (Standard Quality mode)
D-200L
Shutter
D-300L
D-200L
: 1/8 ~ 1/500 sec. (used with mechanical shutter)
: 1/8 ~ 1/500 sec.
Erase
: One frame erase / All frames erase
Image pickup element
: 1/3 inch CCD solid-state image pickup
Exposure
D-300L
D-200L
: Equivalent to ISO 100
: Equivalent to ISO 130
D-300L
D-200L
: 810,000-pixel
: 350,000-pixel
Viewfinder
: Optical real image viewfinder (Parallax
correction mark, backlight correction mark), LCD
monitor
Recording image
D-300L
: 1024 x 768 pixels
(High Quality mode)
: 640 x 480 pixels
(High Quality mode)
LCD monitor
No. of pixels
: 1.8 inches TFT color LCD display
: Approx. 61,000 pixel
D-200L
Auto white balance
Lens
On-screen display : Date and time, frame number, protect mark,
resolution modes, one/all erase mark, battery
remaining warning
: Full auto TTL
: Olympus lens 5 mm, F2.8, 5 elements in 4 groups
(equivalent to 36-mm lens on 35-mm camera)
D
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery charging time for flash
: approx. 6 sec. (at normal temperature with new
battery)
Flash working range
Operating environment
temperature : 0 ~ 40°C / 32 ~ 104°F (operation)
–20 ~ 60°C / –4 ~ 140°F (storage)
: 30 ~ 90 % (operation)
humidity
10 ~ 90 % (storage)
D-300L
D-200L
: 0.2 m ~ 2.4 m (0.65 ~ 7.9 ft.)
: 0.2 m ~ 3.5 m (0.65 ~ 11.5 ft.)
Power supply
: Four AA alkaline batteries (AA NiCd battery, AA
lithium battery, AA nickel hydoride battery can
also be used but the battery check function
won’t work correctly. AA manganese batteries
cannot be used.)
Flash modes
Control panel
: Auto-Flash (automatic flash activation in low light
and backlight), Red-Eye Reducing Flash, Off (no
flash), Fill-in Flash (forced activation)
: Indicates resolution modes, number of pictures
remaining, erase modes, flash modes, Selftimer,
Battery remaining time, Macro mode and writing.
Dimensions
: 145 (W) x 72 (H) x 47 (D) mm
(5.7 x 2.8 x 1.8 inches)
Weight
D-300L
D-200L
Autofocus (only with D-300L)
: TTL system autofocus
: 310 g (11.9 oz) (without batteries)
: 295 g (10.4 oz) (without batteries)
Detection method : Contrast detection system/Focusing range;
0.2 m ~ ∞ (0.65 ft. ~ ∞)
Selftimer
: Electronic selftimer with 12-sec. delay
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT ANY
NOTICE OR OBLIGATION ON THE PART OF THE
MANUFACTURER.
Outer connector : DC input terminal, Data input/output terminal
(RS232C)
Date and time
Automatic calendar system
: Up to 2023.
Power supply for automatic calendar system
: 3 V lithium battery (CR2025) x 1 (changeable)
: Record with picture data simultaneously
F
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
G
Download from Www.Somanuals.com. All Manuals Search And Download.
OLYMPUS OPTICAL CO., LTD.
San-Ei Building, 22-2, Nishi Shinjuku 1-chome, Shinjuku-ku, Tokyo, Japan. Tel. 03-3340-2026
OLYMPUS AMERICA INC.
Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A. Tel. 516-844-5000
OLYMPUS OPTICAL CO. (EUROPA) GMBH.
(Premises/Goods delivery) Wendenstraße 14-16, 20097 Hamburg, Germany. Tel. 040-237730
(Letters) Postfach 10 49 08, 20034 Hamburg, Germany.
OLYMPUS OPTICAL CO. (U.K.) LTD.
2-8 Honduras Street, London EC1Y 0TX, United Kingdom, Tel 0171-253-2772
Printed in Japan 9612 DA 001-2 SU
Download from Www.Somanuals.com. All Manuals Search And Download.
|