Hole Punch Kit
(P/N 42872902)
Technician’s Installation Guide
1. Unpack the Hole Punch Kit and check the
contents:
2. Remove the packing tape, blue spacers and
any other packing materials from the Hole
Punch Unit.
3. Turn off the printer.
4. On the back of the finisher/inverter unit,
unplug the inverter power cord (1) and the
connecting cord ( ) to the finisher.
2
[
[
[
1
2
3
] Hole Punch Unit
] Safety Labels
] Screw (for securing hole punch unit to finisher:
see step 14)
[
[
4
] Orange Cable (4 leads)
] Purple Cable (5 leads)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Remove the screws securing the rear cover
(two on the left side [ ] and one on the right
10. Remove the two screws at either end of the
hole punch blank.
a
side [b]), then remove the rear cover.
a
a
11. Swing up the finisher top cover (
1) and lift
b
out the punch blank unit ( ).
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Remove the top of the blank unit: you need
this to install the hole punch unit. Store the
bottom of the blank in case you ever remove
the hole punch from the finisher.
15. Open the finisher top cover and snap the top
of the blank into place on the hole punch
unit.
13. Align the pins at either end of the hole punch
unit with the holes in the finisher housing,
then slide the hole punch unit into place.
16. Close the top cover and secure the hole
punch unit in place with two screws at either
end.
14. Secure the hole punch unit in place: use two
of the screws (1) you removed earlier, plus
the screw (2) supplied with the hole punch
accessory.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Insert the orange cable (4 leads) into the
connector on the hole punch unit board.
20. Plug the orange cable into the connector on
the main board.
18. Insert the purple cable (5 leads) into the
connector on the hole punch unit board.
21. Plug the purple cable into the connector on
the main board.
19. Snap open the four cable harnesses, then
thread the two cables through the harnesses
and snap each one shut.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
22. Reinstall the back cover and secure it in
23. Reinstall the internal front cover and secure
it with four screws.
place: two screws on the left side (a) and
one screw on the right side (b).
a
a
b
6
Download from Www.Somanuals.com. All Manuals Search And Download.
24. Push the blue knob back into place.
26. Apply the appropriate language safety label:
27. Slide the finisher back into the inverter. Make
sure it locks in place.
25. Close the finisher front cover.
28. Reattach the cable between the finisher and
inverter and the finisher power cable.
29. Turn on the printer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
30. Test the operation of the hole punch unit:
b.Remove the punch collection box from the
finisher.
a.With a suitable document open in a
software application, select
[File]
→
[Print].
b.Select the appropriate Oki printer, then
click [Properties].
c. Click the [Job Options] tab.
d.Under [Finisher], [Output Bin], select
[Finisher(Face-up)] or
[Finisher(Face-down)] from the drop-down
list.
e. Under [Finisher], [Staple], select
[Punch(Long-Edge)] or
[Punch(Short-Edge)], then click [OK].
f. Print the document.
c. Empty it, then put it back into the finisher.
31. Demonstrate how to empty the punch
collection box:
a.Push in on the finisher release lever and
slide the finisher away from the inverter.
d.Slide the finisher back into the inverter.
Make sure it locks in place.
© 2005 Oki Data Americas, Inc.
58372901
Download from Www.Somanuals.com. All Manuals Search And Download.
|