Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Danger
1. Read all safety and operating instructions before using this
product.
Exposure to extremely high noise levels may cause a permanent
hearing loss. Individuals vary considerably to noise induced hearing
loss but nearly everyone will lose some hearing if exposed to sufficiently
intense noise for a sufficient time. The U.S. Government's
Occupational Safety and Health Administration (OSHA) has specified
the following permissible noise level exposures:
2. All safety and operating instructions should be kept for future
reference.
3. Read and understand all warnings listed on the operating
instructions.
4 . Follow all operating instructions to operate this product.
5. This product should not be used near water, i.e. bathtub, sink,
swimming pool, wet basement, etc.
DURATION PER DAY (HOURS)
SOUND LEVEL (dB)
8
6
4
3
2
1
6. Only use dry cloth to clean this product.
7. Do not block any ventilation openings, It should not be placed flat
against a wall or placed in a built-in enclosure that will impede the
flow of cooling air.
90 93 95 97 100 103
8. Do not install this product near any heat sources ; such as,
radiators, heat registers, stove or other apparatus (including heat
producing amplifiers) that produce heat.
According to OSHA, any exposure in the above permissible limits could
result in some hearing loss. Ear plugs or protectors in the ear canal or over
the ears must be worn when operating this amplification system in order to
prevent a permanent hearing loss. If exposure in excess of the limits as
put forth above, to insure against potentially harmful exposure to high
sound pressure levels, it is recommended that all persons exposed to
equipment capable of inducing high sound pressure levels, such as this
amplification system, be protected by hearing protectors while this unit is in
operation.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord being walked on or pinched, particularly at
plugs, convenience receptacles and the point where they exit
from the apparatus. Do not break the ground pin of the power
supply cord.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
11 . Only use attachments specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer or sold with the apparatus. When a cart is used,
use caution when moving cart/apparatus combination to avoid
injury from tip-over.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE CHASSIS. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF NON-INSULATED "DANGEROUS VOLTAGE" WITHIN THE
PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
14. Care should be taken so that objects do not fall and liquids are
not spilled into the unit through the ventilation ports or any other
openings.
15. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way;
such as, power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally
or has been dropped.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.
16. WARNING: To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Download from Www.Somanuals.com. All Manuals Search And Download.
FRENCH
IMPORTANTES INSTRUCTIONS DE SECURITE
1. Lire avec attention toutes les recommandations et précautions
d'emploi avant d'utiliser ce produit.
Danger
2. Toutes les recommandations et précautions d'emploi doivent être
conservées afin de pouvoir s'y reporter si nécessaire.
3. Lire et comprendre tous les avertissements énumérés dans les
précautions d'emploi.
L‘exposition a des niveaux eleves de bruit peut provoquer une perte
permanente de l’audition, Chaque organisme humain reagit
differemment quant a la perte de l’audition, mais quasiment tout le
monde subit une diminution de I’acuite auditive lors d’une exposition
suffisamment longue au bruit intense. Les autorites competentes en
reglementation de bruit ont defini les expositions tolerees aux niveaux
de bruits:
4. Suivre toutes les précautions d'emploi pour utiliser ce produit.
5. Ce produit ne doit pas être utilisé près d'eau, comme par exemple
baignoires, éviers, piscine, sous-sol humides ... Etc.
6. Utiliser exclusivement un chiffon sec pour nettoyer ce produit.
7. Ne bloquér aucune ouverture de ventilation. Ne pas placer le
produit tout contre un mur ou dans une enceinte fernée, cela
gênerait le flux d'air nécessaire au refroidissement.
DURE EN HEURES PAR JOUR
8
6
4
3
2
1
INIVEAU SONORE CONTINU EN dB
90 93 95 97 100 103
8. Ne pas placer le produit près de toute source de chaeur telle que
radiateurs, arrivées d'air chaud, fourneaux ou autres appareils
générant de la chaleur (incluant les amplificateurs producteurs
de chaleur) .
Selon les autorites, toute exposition dans les limites citees ci-dessus,
peuvent provoquer certaines pertes d’audition. Des bouchons ou
protections dans l’appareil auditif ou sur l’oreille doivent etre portes lors
de l’utilisation de ce systeme d’amplification afin de prevenir le risque
de perte permanente de l’audition, Dans le cas d’expositions
superieures aux limites precitees il est recommande, afin de se
premunir contre les expositions aux pressions acoustiquese I evees
potentielIement dangeure u ses, aux personnes exposees aux
equipements capables de delivrer de telles puissances, tels ce
systeme d’amplification en fonctionnement, de proteger l’appareil
auditif.
9. Ne pas négliger la sécurité que procure un branchement polarisé
ou avec raccordement à la terre, Un branchement polarisé
comprend deux fiches dont l'une est plus large que l'autre. Un
branchement à la terre comprend deux fiches plus une troisième
reliée à la terre. Si la fiche secteur fournie ne s'insert pas dans
votre prise de courant. consulter un 'électricien afin de remplacer
votre prise obsolète.
10. Protéger le cordon d'alimentation de tout écrasement ou
pincement, particulièrement au niveau des fiches, des
réceptacles utilisés et à l'endroit de sortie de l'appareil. Ne pas
casser la fiche de terre du cordon d'alimentation.
ATTENTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR.
11. Utiliser uniquement les accessoires spécifiés par le constructeur.
12. Utiliser uniquement avec le chariot de transport, le support, le
trépied, la console ou la table spécifiés par le constructeur ou
vendus avec l'appareil. Lors de l'utilisation d'un chariot, bouger
avec précaution l'ensemble chariotlappareil afin d'éviter les
dommages d'un renversement.
ATTENTION: AFIN DE LlMlTER LE RISQUE DE CHO ELECTR/QUE, NE
PAS ENLEVER LE CHASSIS. NE CONTIENT PAS DE
PIECES POUVANT ETRE REPAREE PAR L’UTILISATEUR.
CONFER LE SERVICE APRES-VENTE AUX
REPARATEURS
13 Débrancher cet appareil lors d'orages ou s'il n'est pas utilisé
pendant une longue période.
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE
DE VOLTAGE DANGEREUX NON-ISOLE A L'INTERIEUR DE CE PRODUIT
QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT IMPORTANTE POUR
PROVOQUER UN CHOC ELECTRIQUE AUX PERSONNES.
14. Des précautions doivent être prises afin qu'aucun objet ne tombe
et qu'aucun liquide ne se répande à l'intérieur de l'appareil par
les orifics de ventilation ou n'importe quelle autre ouverture.
15. Pour toutes interventions techniques s'adresser à un technicien
qualifié.L'intervention technique est nécessaire lorsque l'appareil
a été endommagé de n'importe quelle façon, comme par
exemple si le cordon secteur ou sa fiche sont détériorés,si du
liquide a coulé ou si des objets sont tombés à l'intérieur de
l'apparei1,si l'appareil a été exposé à la pluie ou à l'humidité, s'il
ne fonctionne pas normalement ou s'il est tombé.
CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE
D'INSTRUCTIONS D'UTILISATION ET DE MAINTENANCE DANS LES
DOCUMENTS FOURNIS AVEC CE PRODUIT.
AFIN DE REDUIRE LES RISQUÉ D'INCENDIE ET DE DECHARGE
ELECTRIQUE, NE PAS EXPOSER CET APPAREILA LA PLUIE OU A
L'HUMIDITE.
16. ATTENTI0N:Pour réduire le risque d'incendie ou de choc
electrique ne pas exposer l'appareil à la pluie ou à l'humidité.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Installing the Grand Concerto System in Your Home
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations on the purchase of your NuVo System. The Grand Concerto System is truly NuVo’s newest masterpiece. The Grand
Concerto’s state-of-the-art interface and NuVoNet communication with the Grand Concerto Suite of audio components offer the
best, most affordable whole-home audio system available.
Grand Concerto delivers 80 startlingly clear watts of sound to up to 16 independent zones simultaneously. NuVo’s Generation D,
class D amplification uses the newest technology in digital amplification, which requires less power and is able to operate at peak
capacity while generating very little heat.
The Grand Concerto Control Pad interface offers the elegance and control of an expensive touch panel at a Control Pad price. The
new OLED (organic light emitting diode) display allows up to eight lines of text for easily scrolling through music titles and menu
selections. Capacitive touch controls provide immediate access to the audio sources without external rubber buttons. The result is
a single piece of polycarbonate plastic that provides ultra-responsive water-resistant access to your music from any room of the
house.,
The IR Learning Station makes system setup easy and intuitive. Creating customized audio control is as easy as typing in a
Windows template. The Learning Station will allow IR commands for the source equipment to be stored in files for future use,
making programming the system as simple as the push of a button.
This installation manual outlines the installation and setup of your new Grand Concerto System. We recommend that you read this
manual prior to installing your system. Proper installation and setup will insure years of audio enjoyment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Grand Concerto Back Panel
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE 7&8
ZONE 1
2
ZONE 2
5
ZONE 3
CONNECT TO
NV-I8X
ZONE 4
3
ZONE 5
3
ZONE 6
2
PROGRAM
1
2
1
4
SUM1
SYS ON
6
2
1
3
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
CONFORMS TO
R
4
5
6
SUM2
5
6
7
8
4
5
6
EXT. MUTE
UL STD.6500
CERTIFIED TO
CAN/CSA STD.E60065
1
2
3
4
5
6
C
US
3033118
SOURCE STATUS INPUTS
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM
NuVoNet
DIGITAL LINK
4
3
9
13
5
7
14
1
2
12
10 11
6
8
1. Variable Output: These preamp lineouts are used for sending an audio signal to an external power amplifier. This is useful for
large areas that require additional pairs of speakers. Use the variable output when you want the additional amplifier to be
controlled by the zone’s Control Pad.
2. Fixed Output: These preamp lineouts are used for sending an audio signal to an external power amplifier when additional
speakers are needed. This output is constant, so an amplifier connected to it will not change volume with that zone’s Control
Pad.
3. Source Inputs: The Grand Concerto will accept up to six audio sources. These are connected to the Grand Concerto amplifier
with standard stereo RCA cables.
4. Speaker Output: Six of the Grand Concerto’s eight zones are amplified. These outputs accept 16-gage, two-conductor speaker
wire and provide 40 watts per channel of power.
5. Source Link: This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. The
source link cable is supplied with the Expander System.
6. Source Status Inputs: These inputs are currently inactive on the Grand Concerto. They are intended for future use.
7. Zone Trigger Outputs: These 12-volt outputs can be used to trigger an external device, such as an auxiliary power amplifier, for
use in a specific zone.
8. IR Emitter Outputs: IR signals received from the keypads are passed through the IR outputs to the source equipment using the
supplied IR emitters. Outputs 1-6 are routed to the corresponding sources, and the SUM outputs 1 and 2 are common and will
pass all IR signals.
9. SYS. ON: This is a constant 12-volt output for turning on external equipment. There is no voltage output when the zones are
off.
10. EXT. MUTE: This input is designed to temporarily mute any audio playing through the system when the doorbell or phone
rings. This works in conjunction with the NuVo NV-MI1 mute interface accessory. It also acts as a trigger for whole-house
paging through a phone system when set for this function in the Configurator Software.
11. Network Input: This RJ45 connection is the input for all zone information coming from the Grand Concerto Control Pads. The
connection is made using the Network Cable supplied with the package.
12. Digital Link: This connection is used in conjunction with the Grand Concerto Expander System to create 16 total zones. The
Digital Link cable is supplied with the Expander System.
13. RS232: The bidirectional RS232 is a serial communication port that allows the Grand Concerto System to be controlled by an
external home automation device. It is also used for configuration and programming purposes.
14. AC: A detachable power cord connects the system to an external AC power supply.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Grand Concerto Control Pad
13
12
11
1
2
SVR
1 of 9
Follow the Day
drift
3:09 PM
3
Edge of Tomorr
1:28
3:48
4
5
MENU
OK
10
6
7
9
8
1. Source indicator: This indicates the current audio source playing in that zone. Source names can be customized in the
Configurator Software with a 3 character designation.
2. Cover plate: Each Control Pad comes with white, ivory, almond, and black trim plates that attach magnetically to the face
of the Control Pad. Additional styles of trim plates are available from NuVo.
3. OLED Display: The organic light emitting diode display is a highly functional eight line display.
4. Now Playing/Menu Display: This portion of the display serves two functions. In normal operation, it indicates the artist,
station, metadata, and other source information. In Menu mode it uses a smaller font to display multiple lines of lines of
information for browsing purposes.
5. Volume Level Indicator: This bar graph indicates both the audio volume level when the Control Pad is in normal play mode
and the playback status of digital music files from the M3 audio Server or iPod.
6. Menu: Menu serves as access to music browsing, presets, and favorites, as well as specific zone setting parameters.
7. Power: This button turns the local zone on and off and turns all zones off simultaneously.
8. Play/ Pause: This IR programmable button toggles between the play and pause functions of the chosen source. When
using the T2G Tuners, this button toggles through the Tuners receive modes. A third press and hold function can also be
assigned to this button.
9. OK: The OK button also serves a dual function. In normal play mode, it scrolls through the available audio sources. In
menu mode, it is used to select the highlighted menu item.
10. Arrow Up and Down: These arrows have a dual function. In normal play mode, they control volume level up and down. In
menu mode, they scroll up and down through menu selections.
11. IR Receiver: The Control Pad has a built-in IR receiver for complete wireless control of all the audio source equipment.
12. Forward/Reverse: This is an IR programmable button for simple source transport. Typically it would track forward or back
or tune up and down. A third press and hold function can also be assigned to this button.
13. Time: A feature of the Grand Concerto System is the ability to display the current time on each of the Control Pads.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
NV-GRC1 Remote Control
1. Power: Each zone can be turned on and off, or all
zones can be turned off with this button.
7
2. Volume: This serves two functions. In normal
operation mode, it is a volume control, but when
you are using the menu features of the Control Pad,
it allows scrolling up and down.
MUTE
PWR
1
HOLD
ALL OFF
8
VOLUME
3. Function Buttons: These buttons are currently
inactive and designed for future use.
2
4. Forward and Reverse: These IR programmable
buttons are designed for forward and reverse
functions.
9
SOURCE/OK
5. Favorites: A function of the Grand Concerto System
is the ability to access user defined favorites for
easy access. The first twelve are directly accessible
using the RC1 Favorites buttons.
F1
F2
3
F3
F4
6. DISP: This button allows access to the Display dim
menu available at each Control Pad.
4
7. Function LED: This LED (Light Emitting Diode) lights
to indicate a button push.
10
FAVORITES
1
4
2
5
3
8. MUTE: The RC1 remote provides a discrete mute
function to quickly silence the zone’s output.
9. SOURCE/OK: This is another dual function button. In
normal playback mode it scrolls through the
sources, or in menu mode it selects a highlighted
menu choice.
10. Play/Pause: This IR programmable button toggles
between the play and pause functions of the chosen
source. When using the T2G Tuners, this button
toggles through the Tuners receive modes.
11. MENU: This button enters the menu features of the
Control Pad. When in Menu mode the Volume up
and down buttons scroll through the menu choices.
12. Sleep: This allows access to the sleep timer mode.
13. G1 and G2: These buttons are currently inactive.
They are designed for future use.
6
9
5
7
8
12
10
11
11
12
MENU
SLEEP
DISP
6
G1
G2
13
NV-GRC1
REMOTE CONTROL
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Grand Concerto System in Your Home
I. Prewire
The Grand Concerto System uses CAT5 cable for Control Pad control and either two or four-conductor 16-gauge speaker
wire. All the wire is “homerun” from each zone to the location of the Grand Concerto amplifier and Audio Source equipment.
Complete CAT5 Crimping Instructions
The NuVo audio systems require CAT5, unshielded,
twisted pair (UTP) for communication between the
Control Pads and the main amplifier unit. Each end of the
Top view with
tab down.
wire is terminated with an RJ45 connector.
The Grand Concerto System can accommodate 2,000
total feet of CAT5 cable. For the most reliable operation,
it is best that no single run of CAT5 exceeds 250 feet.
1 2 3 4 5 6 7 8
The correct wiring scheme for the CAT5 cable is standard
Pair 2
Pair 1
Pair 3
Pair 4
EIA/TIA 568A. Properly terminating the CAT5 cable is
crucial for the operation of the system. It is very
important to use a good quality crimp tool, and test each
end to end run with a CAT5 wire tester to insure that your
system operates flawlessly, Fig.1.
Wires insert from
this end.
Fig. 1: EIA 568A wiring scheme for CAT5 Cable
Pin #
1. Green Stripe
2. Green
3. Orange Stripe
4. Blue
5. Blue Stripe
6. Orange
7. Brown Stripe
8. Brown
Step-by-Step Crimping Instructions:
1.
Strip a 2 to 3 inch portion of the insulation,
exposing the 4 twisted pairs.
Untwist the wires and fan them out
2.
individually. Arrange the wires into the
correct color scheme as shown in Fig. 1.
Flatten the wires in their correct order and trim
them evenly across the top. Most crimp tools
Note: Colors listed as “stripe” are a white wire
with a colored stripe.
3.
have a wire trimmer built-in. It is best to trim the wires
to about ½” in length.
Step 1
Step 4
Step 2
Step 3
4.
While holding the wires flat between your thumb
and forefinger, insert the wires into the RJ45
connector so each is in its own slot. Push the
into the RJ45 so all 8 conductors touch the end
the connector. The insulation jacket should
extend beyond the crimp point of the
wire
of
Step 5
Step 6
RJ45.
5.
and
Insert the RJ45 into the crimp tool receptacle
squeeze the tool firmly. Note that a ratchet type
tool should tighten down until it no longer clicks.
The RJ45 should be firmly crimped to the CAT5
6.
insulation. It is necessary that the
color
be repeated identically on each end of
scheme
the wire.
7.
Test each termination with a CAT5 Tester before
completing the installation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Terminating the Speaker Wire (Fig. 2)
Fig. 2
All the NuVo systems operate across a homerun wiring
scheme using CAT5 for the zone Control Pad control
communication, and a separate run of speaker wire for each
zone from the speaker outputs to the zone speakers. We
suggest 16 AWG 2 or 4-conductor speaker wires.
The speaker wire termination is done using a modular Euro
connector. Each conductor is screwed down to the connector
block and plugged into the appropriate speaker output on
the back of the amplifier. The proper termination is Left
channel: – and +; Right channel: – and +.
III. Installing the Grand Concerto Amplifier
LEFT LEFT RIGHT RIGHT
+
+
- -
System setup works best when the amplifier is placed in the
same location as the audio source equipment. This is
typically in an audio rack, entertainment center, or a closet
dedicated to housing the home audio/video equipment.
The amplifier should be plugged in and the power button on
the front panel should be engaged before proceeding with
the rest of the installation. This activates the internal
protective circuitry of the Grand Concerto System.
Fig. 3
IV. Installing the NV-I8GEZP EZ Port (Fig.3)
The EZ Port is a multi-connection hub designed to accept all
the CAT5 wires from the keypads in the system. The location
of the EZ Port should be determined by the location of the
Grand Concerto amplifier. It is best to place in a wall behind
the amplifier that would be easily accessible if necessary.
The EZ Port fits easily in most dual-gang size, low-voltage
ring with an open back. These are often referred to as mud
rings . Simply plug the terminated CAT5 wires into any of
the 20 available jacks on the back of the EZ Port. The order in
which the individual CAT5 wires are plugged in is not
important, although it is strongly recommended that you
label the CAT5 with the appropriate zone number for future
reference.
Once you have plugged the CAT5 wires into the EZ Port, screw
the EZ port into its construction bracket using the supplied
mounting screws.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 4
V. Connecting the EZ Port to the Grand Concerto Amplifier
(Fig. 4)
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
When the EZ Port is installed in the wall, the only part visible
should be the faceplate and four RJ45 jacks. The supplied
pre-terminated network cable can then be plugged into one
of the six available jacks and into the Network connection on
the back of the Grand Concerto Amplifier. Any CAT5 cable
terminated using 568A or 568B network wiring will suffice
should you need a longer connection. Remember, it is
important to terminate the cable the same way on both
ends.
Concerto EZ Port
Model NV-I8GEZP
FIXED
OUTPUT
Device
1
Device
2
Device 3
USE CNLY WITH 250V FUSE
ZONE 7&8
PROGRAM
SUM1
SYS ON
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
NuVo Technologies Cincinnati Ohio USA
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
Device
4
Device
5
Device 6
CONFORMS TO
R
SUM2
EXT. MUTE
UL STD.6500
CERTIFIED TO
CAN/CSA STD.E60065
C
US
3033118
SYSTEM NETWORK
DIGITAL LINK
Connect to
NV-I8GM
NuVo Technologies LLC Hebron, Kentucky USA
www.nuvotechnologies.com
VI. Attaching Audio Source Equipment (Fig. 5)
Fig. 5
Each piece of audio equipment is connected to the Grand
Concerto amplifier with standard stereo RCA cables. Attach
an RCA cable to the corresponding audio output on the
source equipment and to the desired source input on the
back of the Grand Concerto amplifier. The numbered input
for each source is important in the configuration of the
system. This will be covered in detail in the Grand Concerto
Configurator portion of this manual.
Setting up the T2G Tuners, M3 Audio Server, T2SIR Tuner, and
NuVoDock for iPod for use with NuVoNet
A feature of the Grand Concerto System is its ability to
automatically communicate with the T2G AM/FM and
Satellite Tuners, the M3 Audio Server and T2SIR Sirius ready
T2G Tuners
Each of the T2G Tuner components houses two individual
AM/FM or Satellite receivers, which have their own display
on the front panel. Once the T2G is plugged in and the
NuVoNet CAT-5 is connected to the EZ Port and initial
display, OPERATING MODE will appear for each tuner. Below
tuner, and the Wireless and Wired NuVoDocks for iPod. The
AUX IN
AUDIO OUT
USE ONLY NuVo
NV-T2PAS
communication happens through the EZ Port connection
POWERED ANTENNA SYSTEM
TRIGGER
ON=+12V
L
this, the choices are STAND ALONE, SOURCE 6, SOURCE 5,
AUDIO
OUTPUT
R
IN
hub, across a communication protocol called NuVoNet.
ANTENNA INPUT
TUNER
B
SOURCE 4, SOURCE 3, SOURCE 2, and SOURCE 1. Stand Alone
is automatically highlighted at initial startup. Selecting the
appropriate Grand Concerto source input is accomplished by
turning the Select knob for each tuner counter-clockwise
until the desired source input number is highlighted. It is
selected by pushing the Select knob. Once this is complete,
the Grand Concerto NuVoNet will recognize that source.
Although software programming is not necessary for this
function, configuring the installation through the
Configurator Software prior to installation has distinct
advantages, see IX. Grand Concerto Configurator Software.
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
1
2
3
4
5
6
CONNECT TO
NV-I8X
When the T2G Tuners or M3 Server are plugged in for the
USE NV-SLC1
CABLE
1
2
3
4
5
6
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
first time, they will display a prompt to select a source input
ZONE
1
ZONE
2
ZONE
3
SOURCE LINK
number for the Grand Concerto. For NuVoNet to
SOURCE INPUTS
communicate properly, you should have already connected
the NuVoNet components to one of the six Peripheral
Device inputs on the face of the EZ Port.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M3 Server
At initial startup, the front panel display will prompt with
OUTPUTA: PRESS OK TO SELECT NUVONET SOURCE. When OK is
selected, the top line of the display will read OPERATING
MODE OUT A. Below this, the three available lines will display
STANDALONE, SOURCE 1, SOURCE 2 . . . as you scroll using the
down arrow button, SOURCE 3, SOURCE 4, SOURCE 5, and
SOURCE 6 will appear. Highlight the appropriate choice and
press OK to select. This will set the first channel music
output. You will then be prompted to repeat these steps for
the remaining two audio outputs, B and C.
Fig. 6
7
3
5
SUM1
SYS ON
1
3
5
1
6
SUM2
8
2
4
6
EXT. MUTE
2
4
6
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM
NuVoDock for iPod
Both the wired and wireless NuVoDocks for iPod use a simple
rotary switch to set the appropriate source input. Up to two
wireless NuVoDocks and 6 wired NuVoDocks can be used as
individual sources through NuVoNet. The wired and wireless
NuVoDocks consist of the dock for iPod playback and
recharging and a receiver component designed to
communicate with NuVoNet. Prior to plugging the receiver
into the Grand Concerto EZ Port, set the Source rotary switch
to the desired source number input. Once set, the Grand
Concerto Control Pads will automatically display the iPod
information when an iPod is plugged into the NuVoDock.
Each NuVoDock and receiver must have a separate source
number selected.
COMPACT
dISC
NuVo T2G Tuner Direct Numeric Access (Fig. 7)
The NuVo T2G Tuners have the ability for direct IR access to
numeric station tuning. This can be done through the T2G
remote control or using a third party remote control that has
been taught the T2G IR codes. To allow this control, it is
necessary to link one of the Grand Concerto SUM IR outputs
to the Direct IR input on the T2G using a stereo 3.5mm
(1/8 ) mono patch cable. Once the connection is made, the
T2G will respond to the numeric IR commands issued
through the Grand Concerto Control Pad IR receivers.
Note that although the NuVoDock system has a 16 position
rotary switch for source input, only positions 1-6 are used.
VII. Connecting the IR Emitters for Third-Party Source
Components (Fig. 6)
Fig. 7
T2G Tuner IR Input
Model NV-T2DF
Dual XM Tuner
NuVoNet
IR PASS-THRU
NuVo Techonlogies LLC•Cincinnati Ohio USA
IR commands for the source equipment are transferred from
the Grand Concerto amplifier to the source equipment using
the mini IR mouse emitters. Six of these are supplied with
the Grand Concerto System. The emitter is plugged into the
corresponding source IR output on the Grand Concerto and
then placed over the IR receiver window on the source
component. The IR outputs are individually routed to
sources 1-6.
IN
OUT
USB
RS 232
IR INPUT
SYSTEM
7
3
5
SUM1
SYS ON
1
3
5
1
The SUM1 and SUM2 outputs will flash any IR command that
is sent from any of the zones. This is most commonly used
with an IR blaster designed to flash IR commands to a
variety of components.
6
SUM2
8
2
4
6
EXT. MUTE
2
4
6
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM
Grand Concerto IR Ouput
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 8
VIII. Expanding Grand Concerto to 16 Zones (Fig. 8)
Eight additional listening zones can be added to the Grand
Concerto System using the Grand Concerto Expander
package. The expansion is easily done using the Source Link
and Digital Link multi-pin outputs on the Grand Concerto
main amplifier (NV-I8DMS).
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE
1
ZONE
2
ZONE
3
ZONE
4
ZONE
3
5
ZONE
6
ZONE 7&8
PROGRAM
1
2
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-SLC1
CABLE
CONFORMS TO
R
5
6
7
8
UL STD.6500
CERTIFIED TO
CAN/CSA STD.E60065
C
US
3033118
SOURCE LINK
ZONE TRIGGER OUTPUTS
DIGITAL LINK
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE
2
1
ZONE
5
2
ZONE
3
ZONE
4
ZONE
3
5
ZONE
2
6
ZONE 7&8
PROGRAM
1
2
3
6
1
2
4
1
3
SUM1
SYS ON
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
The necessary cables for this are supplied with the Expander
package. No other connections are necessary except the AC
power cord and the additional speaker terminations. The
additional CAT5 wires for zones 9-16 plug into the Grand
Concerto EZ Port.
120V
60Hz 500W
FUSE:T5
A
L
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
CONFORMS TO
R
UL STD.6500
US
CERTIFIED TO
CAN/CSA STD.E60065
3033118
4
5
6
5
6
7
8
4
5
6
SUM2
EXT. MUTE
1
2
3
4
5
6
C
SOURCE INPUTS
SOURCE LINK
SOURCE STATUS INPUTS
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM NETWORK
DIGITAL LINK
IX. Using the Grand Concerto Configurator Software
Fig. 9
The following section includes the optional NV-I8DLS IR
Learning Station. This is available as a package from NuVo
Technologies or any Authorized NuVo Distributor. The
Configurator Software is a PC program designed to run with
Windows 2000, XP, and XP Pro.
1. Main Startup (Fig. 9)
The Configurator is a tabbed Wizard-style interface
designed to sequentially walk the installer through the
system setup. When the program is launched, the Start tab
is highlighted. This gives three choices for beginning a
configuration. You can create a new file, open an existing
file, or retrieve an existing file from a configured Grand
Concerto System. Once configured, the finished program
loaded into the Grand Concerto main amplifier can always be
retrieved via the RS232 port and edited.
Once a configuration file has been opened, you can then
click on the next button to continue. The Configurator will
not let you continue beyond Start without either creating a
new file or opening an existing file. It will also prevent
moving forward through any of the tabs until the necessary
information is completed in any one of the tabs.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 11
1.1 Open or Create Grand Concerto Configurator File (fig. 10)
When you click on this button, the program goes to a Config.
File. There you can either open one of the existing
configurations or specify the name of a new file.
Configurations are saved with a .cfg extension.
1.2 Retrieve Configuration from Grand Concerto
To retrieve a configuration from an existing Grand Concerto
installation, launch the Configurator Software. Make sure
your computer is connected to the RS232 port on the back
panel of the Grand Concerto amplifier. The Startup screen
has two buttons. The first is used to open an existing
configuration or to create a new one. The second asks to
Retrieve Existing Configuration From Grand Concerto.
When you click on the Retrieve button, a progress window
will appear.
2.2 Adding a New Component to the IR Library (Fig. 12)
If you have this configuration already stored on your
computer’s hard drive, you will see a dialog box asking if
you wish to overwrite the existing file. If this file is not
stored in your computer, this box will not appear.
New component IR files are easily added by clicking on the
Add New button. This brings up a new window titled Add New
Component. In this window, you must first enter the
manufacturer name and model. The Type drop-down menu
contains a large list of components. Each is a template of
common functions for that type of equipment. Clicking on
the type that matches the component will add the type name
in that field. If desired, you can add a type name that is not
in the drop-down menu.
Fig. 10
Clicking on OK will automatically add the selected
component and associated functions to the IR Library.
Fig. 12
2.1 IR Libraries (Fig. 11)
The IR Library is a list of available components and their IR
function codes. The Configurator Software stores captured IR
codes in a single directory. Once captured or downloaded,
the Configurator Software will permanently store it as an .irc
file.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 13
Using the IR Learning Station Interface (Fig. 13)
To record new IR codes, you will need the IR Learning Station
Interface. The IR Learning Station Interface is a powerful
tool for setting up new IR Libraries for use with the
Configurator Software, and is part of the IR Learning Station
Package. Capturing function codes and adding them to the
component IR Library is an easy process.
+
-
POWER
12VDC/0.4A
CONNECT TO
CONCERTO D
CONNECT TO
PC
IR
EMITTER
IR
BLASTER
Concerto Learning Station
Model NV-I8DLS
The Interface box is connected to your computer using one
of the RS232 connection cables provided with the IR
Learning Station package. Note that in many cases, personal
notebook computers do not have a Db9 serial cable. In this
case an RS232 to USB dongle cable will be necessary.
PASSTHRU
READY
IR SENSOR
POWER
TEST ACTIVE
When the remote code is entered, the IR Library Record
window will go from yellow to green and indicate that the
capture was successful, and it will then return to yellow.
Repeat this procedure three more times until the desired
code is added to the IR Library Edit window. You will now see
the number of code repeats and the duration of the code. A
normal non-toggling remote will require two button pushes
to successfully record a command, while a toggling remote
will require four button pushes for each command.
The back panel of the Interface box has two IR outputs for
testing purposes. You can use the included IR emitter and
attach it to the IR window on the face of the source
component or to the built-in IR blaster, which, when aimed
at the source equipment, will fire the IR command.
2.3 Recording IR codes (Fig. 14)
When a new component is added to the IR Library, it is
necessary to record the IR codes associated with each
function. To do this, connect the Learning Station Interface
as described above. Double-click on the desired component
from the IR Library page. This will open the IR Library Editor.
This window lists the complete set of functions for that type
of device.
If there is an error in recording the code, the display in the
Record window will indicate that there was a communication
error. If this occurs, click on the Record button and reenter
the code.
Fig. 14
To initiate the IR recording process, you can either double-
click on a function to be recorded or highlight the function
and click on the Record button. This will open the IR Library
Record window. The window will indicate that the
Configurator is Waiting for IR Communications. To record a
new code, simply point the component’s remote control at
the IR receiver on the NuVo IR Learning Station Interface.
The first time you enter a code, the Configurator determines
if it is a toggling function, which means that the remote
sends two commands back-to-back. This requires that the
function button be pressed four times in succession.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 IR Library Default Key Assignment (Fig. 15)
2.5 IR Library Test (Fig. 16)
Once the desired codes are added, assign them to the
appropriate key on the Control Pad. Note that by design, the
Control Pad has only 3 IR programmable function keys and
Power ON/Power Off. Access to multiple preset choices will
be covered later in the Macros section.
An important feature of the Grand Concerto Configurator is
the ability to test each IR code as it is added to the IR
Library. This insures that every code will work reliably.
When a new code is added, while it is still highlighted, click
on the test button, or double click on th e highlighted code.
This will open the IR Library Test window. Make sure that the
IR Learning Interface box’s IR emitter is either facing the IR
receiver window of the source equipment or an IR emitter is
plugged into one of the two IR emitter outputs and affixed
to the IR receiver window of the source equipment. Clicking
on the test button will cause the IR Learning interface to
emit the code. The source equipment should respond
appropriately to the command if it has been stored
correctly. A test result box will open where you can record
yes or no to the test. Three successful test results are
required before the Passed count turns green. Clicking
the OK button will save the results in the IR Library. The
ested column for that command will show the number of
successful tests performed.
To assign default IR functions to the Control Pad buttons,
right-click on each code and select Keys. This opens a
drop-down menu of the possible key selections for the
Grand Concerto Control Pad. Select the appropriate key for
that command and the Configurator will add it to the Default
Key field for that command. The Play/Pause, Prev. and Next
functions have an additional (Held) function. This allows an
additional function assignment that is activated when the
button is held. The Control Pad automatically displays the
function being sent to the source component.
Once this sequence is completed, proceed to the next
function command, and repeat the above steps. When you
have assigned a default key for each IR, click on Done and
that component’s IR Library is complete.
Although not required, testing each
code is highly recommended.
You can also assign discrete power on and off commands.
The Grand Concerto System will initiate the On command
when a zone is turned on and in turn initiate the Off
command when the zone All Off function (holding the Power
button for three seconds) is initiated from any of the Control
Pads.
Fig. 16
Fig. 15
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Select or Edit Source (Fig. 18)
2.6 Adding a Function Code (Fig. 17)
Double-clicking on a blank source will open the Select
Source window. This window assigns the appropriate source
number input. The Display Name is the text that will be
read on the Control Pad when that source is selected in any
zone. The display name can contain only capital letters,
numbers, and some punctuation. If an invalid key is typed, it
will be ignored.
If a required IR function is not in the list of those provided in
the library template, it is possible to add a code to the list
by clicking the Create New button. The pull-down menu
contains a list of all standard IR codes. A name not found in
the list can be typed in, but it is recommended that you use
the names provided in the list. This conserves memory in the
Grand Concerto. Clicking on the OK button proceeds
directly to the IR recording process.
The Make field defines the manufacturer of the
equipment. A drop-down menu allows you to choose a
source from the IR Library. The Model field provides a
drop-down menu that allows you to choose the specific
piece of source equipment from the selected manufacturer.
Fig. 17
An important feature of the Select Source window is the
Gain level control. Different pieces of source equipment
tend to have different levels of audio output signal. This
slider control allows you to compensate for equipment that
has an inherently lower volume level. By using this
adjustment, when switching between sources, relative
volume levels remain constant.
When the appropriate information has been completed, click
OK. This will add the updated source information to the
Source window. When all the desired sources have been
defined, go to Next and proceed to the Macros setup.
2.7 Cleaning Up an IR Library
Fig. 18
Unused IR codes can be deleted from the list by highlighting
the code and either clicking the Delete button or right-
clicking and selecting Delete.
When you are finished editing the library, select Done.
3. Defining Sources
The Sources tab allows you to define the source
component attached to each of the six source inputs. All six
sources are not needed, but at least one source must be
defined.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 20
Adding a NuVoNet Source (Fig. 19)
NuVoNet sources can be placed in the Configuration with the
same procedure as third party IR controllable equipment.
The Configurator program contains IR libraries for each of
the NuVoNet components which have the appropriate button
functions preassigned. Even though the components are
assigned, you must still set the NuVoNet source inputs on
each of the components, see Setting Up the T2G Tuners, M3
Audio Server, and NuVoDock for iPod, pg. 9.
Fig. 19
4.1 Edit Macro Definition (Fig. 21)
The Macro tab has a Source pull down menu that displays the
six sources defined in their order 1-6. When a non-NuVoNet
source is highlighted and selected, three separate points of
definition appear on the right side of the screen. The left
side of the screen is a representation of the Control Pad
display. When the curser is scrolled over the buttons on the
Control Pad, a tool tip appears indicating the function
command or commands that have been assigned to that
button. Here you can double click on the button which opens
the Macro Definition Window. When in Macro Definition, if
you choose to, you can reassign new codes. You can also
double click on the appropriate function in the window on
the right side of the tab and access the Macro Definition
window.
4. Macros (Fig. 20)
An important feature of the Configurator program is the
ability to define source specific macro definitions for third
party IR control. The Grand Concerto has a unique ability to
store specific IR commands as preset names. The best
example is cable or satellite. Using the Macro tab you can
establish a preset name and set the appropriate IR
Fig. 21
commands to select a specific station (this will be covered in
the 4.1 Edit Macro Definition section). Macro definition only
applies to third party non-NuVoNet sources.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 22
If the component had default keys defined in the IR Library,
single IR code macros will be automatically created for each
key. Hovering the mouse over each key in the Control Pad
picture on the left side of the screen will bring up a tool-tip
displaying the name of the macro assigned to that key.
Clicking on the key highlights the macro on the right side of
the screen. Double-clicking on a key in either display will
allow you to change the default assignment or create a new
one in the Edit Macro Definitions window, Fig. 21
4.1.1 Creating a Macro Preset String (Fig. 22)
An important function of the Macro tab is to create a menu
of preset choices for third party components, such as
satellite, cable and CD changers. When a non-NuVoNet
source is selected, a Preset Macro window appears on the
right side of the screen with open spaces for storing preset
station choices. Up to 250 macros can be defined in this
window. When a preset is added to a source, an additional
Preset menu item will be added to that source browsing
capability on the Control Pads. The preset menu is preceded
by the three character source designation established in the
Source tab.
4.1.2 Editing Codes in a Macro (Fig. 23)
When in the Edit Macro Definition window, double-clicking
on a macro step on the right side will open an Edit Macro
Code Settings window. This allows you to change the delay
time before the command is issued. The default delay is .25
seconds. This can be increased by .25-second increments up
to 30.5 seconds. Often a command requires mechanical
movement in the source equipment and, therefore, the
delay is important before initiating the next command.
To create a preset macro, double click on the first available
preset macro selection, Fig. 20. This will open the Edit Macro
Definition window. Once in that window you must type a
name for the preset in the Display Name window. That will
establish the preset name as it will appear in the preset
menu. Note that the Display drop down menu directly below
the Display Name window defaults to Forever. This is the
desired choice for a preset and will keep the preset name on
the Control Pad while that selection is being listened to.
The number of repeats for each command can also be
changed. This is equivalent to pushing and holding the
button on the remote control.
Fig. 23
The available IR codes for that source will be expanded in
green on the left side of the Edit Macro Definition window.
As you double click on a code, it will automatically be added
to the macro string on the right. Up to 255 codes can be
added to a single macro and the codes will fire in the order
in which they are added to the string. Once the desired
macro string is complete, click done and return to the main
macro tab. The completed macro will appear in the Preset
Macro window. To create a second preset, double click on the
next space and repeat the Macro Definition steps.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 24
Re-Ordering Macro Codes
After a code is added to a macro, highlighting a code and
clicking on the Ýor ßbutton will reorder the codes.
Macros (updated)
After editing a macro, the macro list is updated to show the
number of IR codes and the display name.
Note that the Macro tab has an additional button at the
bottom that says Update Macros From Library. If codes
were edited in any way in an IR library after a source has
been defined in the Source tab, this button will
automatically pull those changes into the Macro Definition
window.
5.1 Edit Zone Properties (Fig. 25)
4.1.3 Control Macros
Double-clicking on a zone number opens the Edit Zone
Properties window. Specific properties defining that zone
are set here.
An additional option within the Macro tab is the ability to
establish multiple control macros. These macros are
intended for instant access to control functions and are an
optional feature. If a control macro is created, an additional
source menu item is also created titled Control preceded
by the three character short name assigned in the Source
tab.
Max Volume: This allows the volume in a zone to be limited.
This can be done either to avoid damage to low-power
speakers or simply to prevent a certain room from being
turned up too high (e.g., a teenager’s bedroom).
Party Volume: This controls the reset volume level for each
zone when the All On/Party Mode is initiated from any of the
Control Pads. The range is 78dB to 30dB.
Creating a control macro is the same process outlined in
4.1.1 Creating a Preset Macro String on page 17.
Page Volume: If you are using the paging feature of the
Grand Concerto System, you can also set the specific volume
level of the page zone by zone, by using this volume control.
The range is 78dB to 30dB, with a default at 40dB.
5. Zones (Fig. 24)
Up to 20 zones can be defined with the Grand Concerto. Each
zone can be defined with unique properties.
Balance: The level of output to the left and right speakers is
adjusted here. The default is center, but depending on the
location of the speakers and the optimal listening area of
the room, it may be advantageous to adjust the balance to
either the left or the right.
You will notice that the zone tab contains 20 entries for zone
Control Pads. The system can accommodate a total of
20Control Pads by using the slave function in the Edit Zone
Properties window. A slave Control Pad is homerun to the EZ
Port, but automatically shares the same functions and works
in tandem with the main zone Control Pad. Up to three slave
Control Pads can operate on a single zone.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Source Grouping: This allows for one zone to automatically
listen to the same source as all other zones in the group. This
is a very useful feature for a large open area where it is not
practical for more than one source to be playing at one time.
The advantage of the zone group is that each Control Pad
within the group has the ability to turn on or off, mute, and
control volume independently. This drop-down menu allows
any zone to be assigned to a group, or as an individual zone
with no group affiliation. Up to four distinct groups can be
created.
Bass and Treble: Both bass and treble can be adjusted
individually on a zone by zone basis. The EQ sweep is -18dB
to +18dB. Keep in mind that these levels can also be set at
the zone Control Pads with music playing. This will be
covered later in the Control Pad menus.
Volume Reset at Zone ON: A zone-specific feature is the
ability to have a zone automatically reset to a low volume
level when the zone is turned on. This check box initiates
that feature and is tied to the Zone Reset Volume level set
above it. If this box is not checked, the zone will turn on at
the last volume level.
Lock Zone By Default: This check box turns on a function that
automatically prevents any functionality from the zone until
the assigned security code is entered. Primarily, the
function prevents an outside zone from being turned on
except when the homeowner really wants to listen to it.
Loudness Compensation ON: This box defaults to checked and
enables an automatic bass and treble boost when the zone is
at a low listening level. This EQ gradually flattens out as the
zone volume is increased. Unchecking the box turns this
function off.
Display Time While Zone Off: Checking this box causes the
Control Pad to automatically display the current time when
the zone is turned off. In normal operation the time is always
displayed in the upper right corner. The time is automatically
set according to the computer when the configuration is
downloaded to the Grand concerto.
Exclusive Source Control: Checking this box gives this zone
exclusive do not disturb control of any chosen source.
Other zones will have the ability to listen to that source, but
they will not have any specific function control.
Do-Not-Disturb: This Section is used to lock out system-
wide commands from a specific zone.
IR Pass-through: Each zone Control Pad has an IR receiver
for wireless remote control. By its nature, IR is susceptible
to external interference. To account for this, there is specific
IR pass-through settings for each Control Pad. IR Disabled
turns off the IR receiver completely and eliminates any
possibility of a competing light source. This is useful in an
environment in which the Control Pad receiver is competing
with overwhelming sunlight. This will prevent IR
communication throughout the system and therefore, it is
better to eliminate that light source. IR No Pass-through
prevents third-party remote control commands from being
accepted, but still allows the NuVo NV-GRC1 remote control
to operate the system. In some zones this is necessary when
a third-party remote is often used to control a non NuVo
System source such as a TV. This would eliminate that remote
control’s commands from being received by the Control Pad
and passed through to the source equipment.
No Mute: The Grand Concerto System has a small
accessory called the Mi1, Mute Interrupt which is
designed to mute all zones when the phone or doorbell
rings. This is defeated on a zone by zone basis by
checking the No Mute box.
No Page: The Grand Concerto System is capable of paging
through audio source input 6. This involves a phone
system that has a paging audio output and a means to
provide a voltage trigger. This is controlled using the
System Settings tab to set the voltage trigger and
utilizing the Mute Interrupt, see Mute Interface page, 31.
Setting the system s Mute input for paging or the Mi1
mute function is covered in the next tab.
No Party: Master and Party Mode refer to the ability to
turn all zones on simultaneously. In some zones you may
not want this function.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Enabled Zone Sources: These allow individual sources to be
turned off for specific zones. A source that is turned off will
not display in that zone. This is particularly useful in
preventing child access to a source dedicated to adult
listening.
5.2 Zones (updated) (Fig. 26)
When the desired properties for each zone are set, click on
OK. This will return you to the Zones tab. There you will see
an updated list of the zones by the number they are
assigned, as well as the specific parameters defined in the
Zone Edit window.
Display Settings: The overall brightness and AutoDim
feature for each Control Pad are set using these drop-down
menus. The first menu is the display brightness. The choices
are Dimmest, Dim, Not So Bright, Normal, Bright, Brighter,
Brightest. The second menu sets the duration for the
AutoDim feature. These range from AutoDim Disabled, 15 Sec
up to 1 Hour. The next menu sets a specific AutoDim level.
AutoDim Brightness Off removes all display and backlighting.
Using AutoDim Brightness Low, AutoDim Brightness Medium,
or AutoDim Brightness High reduces the level of brightness,
but does not make the Control Pad completely dark.
Double-clicking on the zones will reopen the edit window,
where any of the definition properties can be modified.
Fig. 26
Slave To: This drop-down menu is used to assign additional
slave Control Pads to a zone. Up to 20 Control Pads can be
used in an installation. The EZ Port hub is equipped with 20
RJ45 ports to accommodate all the system’s Control Pads.
This is a useful feature for large rooms where more than one
Control Pad is desired. If slave Control Pads are used, we
suggest that you disable the IR pass-through on those to
prevent cross-communication. The Slave To function can
also be used to tie two or more zones together under the
control of a single Control Pad.
6. System Settings
Fig. 25
This tab is used to define the way in which the External Mute
input functions, for setting the zone lockout security code,
set the clock for 24 hour display and if necessary to set a
serial communication display.
6.1 External Mute: System Mute Trigger (Fig. 27)
The Grand Concerto System has an accessory, the NV-MI1
Mute Interface, which is designed to mute any music playing
through the system when a doorbell or phone rings, see MI1
Mute Interface. When setting the System Mute Trigger, set
the mute input to respond to the contact closure provided by
the MI1.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 27
6.3 24 Hour Time Display and Power Off Mode
24 Hour Time Display: By checking the 24 Hour Time Display
box the system will automatically go to a 24 hour clock on
each of the zone Control Pads.
Power Off Mode: The Grand Concerto Configurator allows the
option for three power off modes.
Tap Mute/Hold for Zone-Off w/ All-Off Menu: This mode
causes a temporary zone mute when the Control Pad
power button is tapped. When it is held a second menu
will appear with the options to turn the zone off or turn all
the zones off.
Tap Zone-Off/Hold for Group/All-Off Menu: In this mode a
single tap of the power button turns the zone off and
holding the power button causes a second menu that
gives the option to turn off that zone s group or turn all
the zones off.
6.2 External Mute: Paging Trigger (Fig. 28)
Tap Zone-Off/Hold for All-Off (no menu): This is the
default choice. In this mode, a tap turns the zone off and
holding the power button turns all the zones off.
The Grand Concerto System has a built-in solution for
whole-house paging typically through a phone system. The
Paging Trigger setting causes the system to mute across all
the zones, and in turn, amplifies the page across all zones.
Each Zone Edit utility in the Configurator Software or the
menu at each Control Pad offers the capability of setting the
page volume in each zone.
6.4 Serial Delay (Fig. 29)
This drop down menu provides a choice of delays measured
in milliseconds. This is only necessary when you are using
the RS232 communication for third party control of the
Grand Concerto System. This utility slows the rate at which
information is delivered to the home automation system
from the Grand Concerto. This is sometimes necessary to
allow the home automation s processor time to buffer the
incoming information.
Fig. 28
Fig. 29
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 31
6.5 Security Code (Fig. 30)
A feature with the zone setup of the Grand Concerto System
is the ability to lock the zone. This can be done as a default
that will require a four-digit security code to unlock the
zone Control Pad when the zone is turned on, or it can be
done as a temporary setting from the Control Pad menu to
lock the zone on its current listening choice. In either
scenario, the security code must be set to unlock the zone.
The security code can be any four digits or left at the default
5555.
Fig. 30
Fig. 31a
7. Update System (Fig. 31)
Firmware Upgrade
Please Wait. . .
The finished configuration is now ready to be downloaded to
the Grand Concerto amplifier. While downloading, a progress
box will show download progress. Once complete, the
configuration is permanently stored in flash memory.
Configurations can always be retrieved and edited at a future
date.
MENU
OK
Control Pad Firmware Update (Fig. 31a)
When first plugged in and addressed, the Control Pads will
poll the main unit for the correct firmware version. If they
are at a lesser version number, an upgrade notice will appear
on the display. It is important to allow this process to
complete. When the Control Pad is finished upgrading itself
it will turn off. At that point, it is ready for zone control use.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
X. Control Pad Setup
XI. Using the Control Pad's MENU Button
Menu gives access to specific music selection and control for
each source, as well as zone and system setting capability.
When the MENU button is pushed, the display goes to an
eight-line screen labeled Main Menu.
Factory-new Installation
The system should be programmed with the Configurator
prior to setting up the Control Pads for the first time. The
Grand Concerto amplifier should be placed in its permanent
location, plugged in, and turned on. When a Control Pad is
plugged in for the first time, the following sequence will
occur:
MAIN MENU: There are four Main Menu items that are
consistent to all source selections and pertain to general
system and zone control. They are Favorites, Sources, Advanced
Zone Control and Setup, Fig. 32.
1. When first plugged in, Grand Concerto V. X.XX where
X refers to the current firmware version number
loaded in the Grand Concerto main amplifier unit.
The Control Pad will then go to the Zone Selection
menu.
2. Press the Power Button to turn the Control Pad on.
The display will flash the Grand Concerto and
Version number screen and immediately go to Zone
Selection. If you have loaded a configuration into
the main unit, once in Zone Selection mode all the
configured zone names will appear starting with the
first. If you are setting the system directly out of
the box, it will simply list generic Zone 1, Zone 2,
etc., up to Zone 20. Setting the appropriate zone
address is simply done by using the arrow buttons
to scroll up or down to the appropriate zone and
pressing the OK button.
Fig. 32
Main Menu
Favorites
Sources
Adv. Zone Control
Setup
Favorites: Top-line favorites are global. Favorites or play
lists set up within Windows Media Player and synced with
the NuVo M3 Server or within an iPod can be added to the
Favorites list. Potential members of this list can also include
station presets for the NuVo T2G or other sources such as
satellite or cable. When T2G or IR Macro Presets are
assigned, the first twenty are placed in the Favorites menu.
Assigning playlists within the M3 or iPod to global favorites
is done in the M3 Options or iPod Options menu, Fig. 33. This
menu item automatically resides with the M3 or iPod as a
source choice. Once in the Options menu, the choices are
Shuffle, Repeat and Edit Favorites, Fig. 34. When Edit
Favorites is chosen, Add to Favorites will allow you to add
any playlists from the hard drive of either the M3 or iPod,
Fig. 35. When the desired choice is highlighted, pressing the
OK button completes the task.
3. The Control Pad will flash the version-number
screen one more time and immediately turn off.
When powered on, the addressed Control Pad will
then go to the first established source.
At this point, the zone may be operated by the parameters
set in the configuration. Zone settings may be modified
using the MENU key.
Reprogramming the Zone Address
Fig. 33
Main Menu
Albums
Genres
This procedure allows an addressed Control Pad to be moved
to a new location. Within the main menu of each zone, go to
Setup. Within the Setup options, scroll to Advanced Settings
and to Zone Number. All the used addresses will be grayed
out. Any available addresses will be accessible. Scrolling to
None will erase the current address.
Tracks
Play All
M3 Options
Adv. Zone Control
Setup
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 34
Advanced Zone Control: Advanced Zone Control is designed
for user access to temporary zone settings. Each of the zone
parameters set in advanced zone control automatically reset
when an All Off command is issued from a Control Pad, Fig.
37.
Options
Shuffle
Repeat
Edit Favorites
Fig. 37
Adv. Zone Control
Party Mode
Fig. 35
Do-Not-Disturb
Sleep
Lock Zone
Edit Favorites
Rock
Lock Zone & Off
Dinner Party
--Add to Favorites...
Party Mode: This setting is turned on and off with the
OK button. When selected all the configured zones in
the system will turn on and that Control Pad becomes
the Host for the entire house. This function is defeated
in an individual zone by initiating a function on that
zone s Control Pad.
Sources: This offers quick access to the six sources defined
in the system. Third-party sources can be defined with a
source name in the Grand Concerto Configurator Software, or
they are labeled by the system as a generic source number.
The NuVoNet sources have a predefined system name unless
you choose to assign a customized name in the Configurator
Software, fig. 36.
Do-Not-Disturb: This sets a temporary source lock on a
chosen source within that zone. This selection is also
turned on and off by pressing the OK button.
Sleep Mode: The Sleep Mode when set, allows music to
play in that Control Pad s zone for a specified amount of
time, Fig. 38. Once the time selection is made, the
system will gradually ramp down in volume and the zone
will turn itself off at the end of the selected time.
Fig. 36
Sources
NuVo M3 A
NuVo M3 B
NuVo M3 C
NV-T2G AM/FM
NV-T2G XM
Cable
Fig. 38
Sleep
Off
15 Minutes
30 Minutes
60 Minutes
90 Minutes
120 Minutes
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Lock Zone: This temporarily locks the zone on the
current source selection. It requires a four digit security
code that must be set in the Settings Tab of the
Configurator Software. The security code is entered on
the Control Pad by using the up and down arrows to
scroll to the first number and pressing OK. The display
will then highlight the next number. Using the process
described above, set the second, third and fourth
numbers. Once the fourth number is set, the zone will
remain locked until the security code is entered to
unlock it, fig. 39.
Favorites #1-12: Twelve global favorites can be defined
for easy access from within the Main Menu or from the
twelve numeric favorites from the Grand Concerto
remote control. Any favorites, which include M3 and
iPod play lists, tuner presets and specific disc selections
can be selected in the Favorites setup and automatically
added to the global list. The Grand Concerto Remote
Control has a 12-button numeric Control Pad that
provides direct access to the 12 assigned favorites.
When a favorite is selected, the zone will automatically
go to the appropriate source and music selection, Fig.
41.
Lock Zone & Off: This temporary lock works very much
like Lock Zone, but is used to turn the zone off and
requires the security code to turn the zone back on.
Fig. 41
Favorites #1-12
Rock
Jazz
Fig. 39
Sports Talk
(Empty)
(Empty)
Lock Code? (5)
(Empty)
(Empty)
4300
Zone Settings: This selection contains several zone specific
controls, Fig. 42. Note that Advanced is grayed out and is
preceded by an asterisk. This is an installer specific level
that is accessed by holding the OK button for six seconds.
Note that the security code is set in System Settings tab
Setup: The Setup menu is for specific system setup. It
consists of several subset menus, Fig. 40. These are defined
in the next section.
Fig. 42
Zone Settings
Balance
Bass
Fig. 40
Treble
Loudness Comp.
Volume Settings
Display Settings
*Advanced
Setup
Favorites #1-12
Zone Settings
*Source Settings
System Settings
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 44
Balance: This controls the level of audio going to the left
and right speakers. In some cases, when the listening
area is not absolutely centered between the speakers, it
is useful to adjust the center listening point left or
right. This menu option gives the ability to adjust the
sound left or right up to 18 steps in either direction.
Bass: This adjusts the frequency level from 100Hz and
below. The default is flat, and the range is 18dB to
+18dB.
Adv. Zone Settings
Source Lockout
Exclusive Src. Ctl.
Group
Default DND
Default Zone Locked
Remote Controls
Slaved to Zone
Treble: This adjustment works within the same
parameters as the bass and adjusts the frequency level
from 10kHz and up.
Loudness Compensation: Loudness can be simply turned
on or off by pressing the OK button.
Source Lockout: Any source selected in this menu will be
locked from access within that zone.
Exclusive Src. Ctl.: This sets a default that automatically
grabs control of any source chosen within this zone.
Other zones will be able to listen, but they will have no
specific source control. This is a permanent zone setting.
Group: Source Group is a great NuVo feature for large,
open-floor living spaces. In this menu option, any zone
can be set to share source among a group of zones to
prevent the likelihood of having more than one source
playing in the same open space. The advantage to Source
Group is that each zone area maintains individual on/off
and volume capability.
Volume Settings: There are several default settings
available in this menu. Volume Reset is turned on or off
by pressing the OK button and controls whether the
zone turns on at its previous volume level, or to a preset
level, Fig. 43. If checked, the volume at zone on reverts
to the level set in the next menu item, Initial Volume.
Choosing to set at the current listening level, or
selecting the default 60 dB level, controls this level.
Maximum Volume is an overall zone volume limit and is
set in the same manner as Initial Volume. Page Volume
controls the level at which a page is amplified in each
zone, and Party Volume sets the initial volume level
when the party or all-on function is initiated.
Default DND: This prevents the global functions of all-
on or party and whole-house page from a Control Pad’s
specific zone, Fig. 45.
Fig. 45
Fig. 43
Default DND
No Mute
No Page
Initial Volume
Set (current volume)
Reset (-60 dB)
No Party
Default Zone Locked: A locked zone prevents anyone
from turning the zone on and accessing music without
first entering the security code.
Advanced Zone Settings: These are parameters for each zone.
They can be easily established in the Configurator Software
or here at each of the zone Control Pads, Fig 44.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Controls: These settings affect the way the
Control Pad receives commands from a handheld
wireless remote. The NV-GRC1 is the system remote that
comes with the Grand Concerto. It allows the same level
of control as the Control Pad. At the default setting, All
Remotes Enabled, this remote and any third-party IR
remote will be received by the zone’s Control Pad. In
some instances, you may not want a third-party remote
command to be received by the Control Pad. In this case,
you would choose NuVo Remote Only. If the zone is in an
area that is flooded with sunlight or receives
Source Settings: Two choices reside in this menu, Fig. 47.
Gain: This lets you increase the audio input levels from
the sources coming into the Grand Concerto. This is not
necessary for the NuVoNet components, but if you use a
satellite or cable set-top box as an audio source for the
system, you will find that the audio level is inherently
softer and will benefit by the gain setting. The default is
0dB, with a range up to 18.75dB.
NuVoNet Source: If you uncheck this selection, that
source will not be polled by NuVoNet and will only be IR
controllable.
interference from plasma displays, the best choice is All
Remotes Disabled.
Slaved to Zone: A feature of Grand Concerto is the ability
Fig. 47
to slave zones together. This is most useful for
Cur. Source Settings
Gain
NuVoNet Source
controlling a zone with more than one Control Pad, or
the converse, which is controlling more than one zone
with one Control Pad. Simply scroll to the zone you wish
to slave to and select it from the list, Fig. 46 .
Fig. 46
Slaved To Zone
None
Kitchen
System Settings: This menu option controls system-wide
settings, Fig 48.
Dining Room
Master Bedroom
Master Bath
Guest Room
Nursery
Fig. 48
System Settings
Date/Time
24 Hour Time Display
Power-Off Mode
*Advanced
Zone Number: Each zone must be assigned a number or
specific zone address. This is done by scrolling to the
desired zone and selecting it. All used zone addresses
will be grayed out. If you have defined zones in the
Configurator Software, the actual zone names assigned
in the Zone tab of the software will appear in the list.
The zone list appears just as it does in the previous
Slaved Zone menu. Scrolling to a different zone name
and pressing OK will set a new zone address, or
selecting NONE erases the zone address.
Diagnostic Self Test: This performs a short display
parameter test when selected
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 50
Date/Time: The Grand Concerto has an internal clock
that allows each Control Pad to display the current time.
Within this menu you can easily set Year, Month, Day,
Hour, and Minute.
24 Hour Time Display: This is a simple on/off. When this
menu item is turned on, the clock display on the Control
Pads switches to 24 hour display.
Advanced
Ext. Mute/Page
Serial Delay
Sources
Reset System
Power Off Mode: This refers to three choices for the way
in which each zone turns on and off. They involve a
single tap of the power button and a hold function, Fig.
49.
Mute/Off/ w/ Menu is the first choice. This selection
means that a tap of the power button mutes the zone,
but does not turn it off. The hold function brings up a
second menu that requests All Off, yes or no. No turns
off just that zone, yes turns off all zones.
Off/All-Off Menu: In this mode, a tap of the power
button turns the zone off and a second menu appears
that gives to choice to turn off that zones group (if it is
assigned to a source group) or to turn all zones off.
Off/All-Off: The is a tap of the power button to turn the
zone off and a hold of the power button to turn all zones
off.
External Mute/Page: The EXT. MUTE input on the back
panel of the Grand Concerto has a dual function. In
normal mode, it is designed for the Mute Interface, NV-
MI1 (see NV-MI1 Mute Interrupt Adaptor page, 31). It
can also be configured for use with a paging phone
system to enable whole-house paging. This requires a
phone system that provides an audio output for paging
that is plugged into source input 6 on the Grand
Concerto (note that this feature eliminates the use of
Source 6 as an audio source for the system). To use the
Page function, you must select Paging Mode. There are
two types of voltage triggers associated with the Page
function. If the phone system you are using sends a
voltage to trigger paging, selecting Paging Mode sets
the mute input to react and mute all zones. If it triggers
by creating a closure (dropping down to 0 voltage), you
need to select Active Low (Closed).
Serial Delay: This function is only used in conjunction
with third party home automation systems. This
function sets a delay in milliseconds between each of
the function commands being streamed through the
Grand Concerto RS232 port. This allows a slower home
automation processor to buffer multiple commands
from the Grand Concerto System.
Fig. 49
Zone Power-Off Mode
Tap/Hold Action
Mute/Off w/Menu
Off/All-Off Menu
Off/All-Off
Sources: This Allows unused source inputs to be turned
off so they do not show up when you scroll through the
sources at the Control Pads.
Reset System: This is a shortcut for resetting the zone
addresses assigned to each Control Pad. Within the
menu selection, Yes restores all Control Pads plugged
into the system to the factory default.
Advanced: Within the System settings menu are advanced
functions intended for installers. The item is preceded by an
asterisk and grayed which requires that the OK button is
held for six seconds before the advanced functions are
accessible, Fig. 50.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
XII. Grand Concerto Accessories
The NV-I8DLS IR Learning Station Interface
Concerto Learning Station
Model NV-I8DLS
PASSTHRU
READY
IR SENSOR
POWER
TEST ACTIVE
3
4
5
2
1
1. PASSTHRU: This LED (light emitting diode) remains lit when the Interface box is actively passing IR information through the
system.
2. READY: When you are inputting IR codes into the Configurator using the Interface box, this LED will light when the system is
ready to learn a new code.
3. IR SENSOR: This is the IR receiver used when capturing codes for new source equipment.
4. TEST ACTIVE: When you are testing an IR code, this LED lights momentarily when the code is actually firing.
5. POWER: This LED remains lit when the interface box is plugged into an AC electrical outlet.
+
-
POWER
12VDC/0.4A
CONNECT TO
CONCERTO D
CONNECT TO
PC
IR
EMITTER
IR
BLASTER
5
4
3
1
2
1. AC Power: A standard 12-volt power supply is included in the Learning Station Package. This will supply the necessary AC power
for IR learning and testing.
2. CONNECT TO PC: Using one of the supplied RS232 cables, connect from the RS232 port on your computer to this input on the
Learning Station Interface.
3. CONNECT TO GRAND CONCERTO D: Using the second RS232 cable, connect the Learning Station Interface to the Grand Concerto
amplifier’s RS232 port.
4. IR EMITTER: An IR mouse emitter is supplied with the Learning Station package. A feature of the Configurator Software is the
ability to test each new code that is learned by the interface. The software will send the IR command to the source equipment via
the IR emitter so you can have visual reference that the source equipment responded appropriately to the command.
5. IR BLASTER: Another built-in IR test method is the use of the blaster. The test process is the same in the Configuration
program, but the IR Blaster allows you to point the back of the Interface box toward the source equipment IR receiver. This fires
the IR command and eliminates the need for the mouse emitter.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Capturing IR codes using the IR Learning Station Interface
The Grand Concerto Configurator Software is designed to store IR codes for audio equipment in an IR Library. When the codes are
learned for a given piece of equipment, they are held in the library under that equipment’s manufacturer name and model
number. Once learned, any of the equipment in the library can be imported into a new Configuration.
To learn new equipment codes, the Learning Station Interface box must be connected to your computer at the RS232 port. Connect
the male end of the RS232 cable to the back of the Interface box into the CONNECT TO PC input. At this point, it is not necessary
to have the Interface box connected to the Grand Concerto amplifier.
When setting up a new source, each type of equipment has a pre-selected set of functions. By double-clicking on a function or
clicking on the Record button in the software, you will open the record window. You will see the READY LED light on the
interface box. Aim the source’s remote control at the IR SENSOR on the Interface and press the desired function button on the
remote. The IR learning window in the Configurator Software will indicate that the code has been successfully learned. Note that
the remote control should be held 8 to 10 inches from the Interface when learning.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
NV-MI1 Mute Interrupt Adaptor (Fig. 51)
The Mute Interface is used in conjunction with System Mute input on the back of the Grand Concerto amplifier. It acts as relay for a
voltage from up to two phone lines and two doorbell transformers. When a voltage is presented to the MI1, it sends a contact
closure to the Grand Concerto System, which causes the system to mute momentarily. This is useful in allowing the telephone or
doorbell to be heard when audio is playing in any of the zones.
The NuVo NV-MI1 Mute Interface Module is designed to automatically mute any audio playing through the System s speakers when
the telephone or doorbell rings.
Fig. 51
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE 7&8
ZONE 1
2
ZONE 2
5
ZONE 3
CONNECT TO
NV-I8X
ZONE 4
3
ZONE 5
3
ZONE 6
2
PROGRAM
1
2
6
2
4
1
3
SUM1
SYS ON
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
L
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
R
R
CONFORMS TO
R
4
5
6
SUM2
5
6
7
8
4
5
EMITTER OUTPUTS
6
EXT. MUTE
UL STD.6500
CERTIFIED TO
1
2
3
4
5
6
C
US
CAN/CSA STD.E60065
SOURCE STATUS INPUTS
3033118
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
SYSTEM
DIGITAL LINK
NETWORK
The MI1 connects to the NuVo amplifier using a standard
mono patch cable with a mini-plug on each end. Plug one
end into the EXT. MUTE input on the back of the amplifier
and the other end into the input on the front of the MI1.
The back of the MI1 will accept up to two AC or
DC voltages from two different doorbell chimes.
This connection is done with two conductor wire
from the terminals on the doorbell chime to the
Doorbell A or Doorbell B inputs on the back of the
MI1. Polarity is not important for this connection.
A
B
DOORBELL 1
MUTE INTERFACE
ADAPTER
NV-MI1
A
B
DOORBELL 2
CONNECT TO
MUTE INPUT
Connect to Telephone RJ-11
Line 1: Pins 3,4 Line 2: Pins 2,5
Model NV-MI1
Mute Interface Module
Up to two phone lines can be brought into the
Rj11 connection on the back of the MI1. The
voltage from the phone ringer will trigger the
NuVo System to mute.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
NV-LSI24 Local Source Interrupt (Fig. 52)
The Local Source Interrupt enables an amplified local audio source to override the Grand Concerto System and play through the
local zone in-wall speakers. The most common scenario for this is a television that would benefit from higher-quality speakers.
The back of the Grand Concerto Control Pad has two CAT5 inputs. One is labeled NuVoNet and is the CAT5 that runs to the EZ Port at
the head end. The other is labeled NV-I8GLSA. This is intended to react to the LSI24 accessory. It requires an RJ45 connection at
the Control Pad end and the Brown and Brown Stripe pair as a voltage trigger.
Note that the Local Source Interrupt is a passive non-amplified device. The signal sent to it must be amplified.
Fig. 52
The connection from the LSI24 is made through the
NV-IG8LSA RJ45 port on the back of the Control Pad
terminated with standard 568A. The connection at
the LSI24 requires the use of the Brown lead for
positive and Brown Stripe for negative.
The selected zone speaker output of the Grand Concerto
amplifier is wired directly to the LSI24
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE
2
1
ZONE
5
2
ZONE
3
ZONE
4
ZONE
3
5
ZONE
2
6
ZONE 7&8
PROGRAM
1
1
6
2
3
1
2
4
1
3
SUM1
SYS ON
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
R
R
CONFORMS TO
R
UL STD.6500
4
5
6
5
6
7
8
4
5
6
SUM2
EXT. MUTE
NV-I8GLSA
NuVoNet
1
2
3
4
5
6
C
US
CERTIFIED TO
CAN/CSA STD.E60065
3033118
SOURCE STATUS INPUTS
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM NETWORK
DIGITAL LINK
SVR
1 of 9
3:09 PM
Follow the Day
drift
Edge of Tomorr
1:28
3:48
MENU
OK
Grand Concerto
Control Pad
The positive and negative connection on the
LSI24 act as a relay relay switch between the
local source input and the audio coming from
the Grand Concerto System. When zone is
turned off, is routed to the speakers. When
the zone is on, the Grand Concerto audio goes
to the speakers.
Model NV-LSI24
Mute Interface Module
Two or four conductor speaker wire from the
LSI24 to the zone speakers.
LOCAL SOURCE
SWITCH
NV-LSI24
RLY+
RLY-
To Control Pad
L-
CONNECT TO
AMPLIFIER
L-
L+
R-
L+
R-
R+
R+
Amplified signal from the local zone source
Speaker input from Grand Concerto
32
Download from Www.Somanuals.com. All Manuals Search And Download.
NV-LSA40 Local Source Amplifier (Fig. 53)
The LSA40 is a 40 watt stereo amplifier designed to fit neatly in a single gang box or ring. Its active state provides a ready input
for any line level audio signal. When connected to the Grand Concerto Control Pad, the Grand Concerto speaker output and the
LSA40 share a common pair of speakers in a zone. The LSA40 s internal A/B switch allows NuVo audio when the zone Control Pad is
turned on and local audio through the LSA40 when the zone Control Pad is turned off.
Fig. 53
NuVo System zone
speakers.
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE
2
1
ZONE
5
2
ZONE
3
ZONE
4
ZONE
3
5
ZONE
2
6
ZONE 7&8
PROGRAM
1
1
6
2
3
1
2
4
1
3
SUM1
SYS ON
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
R
R
CONFORMS TO
R
UL STD.6500
4
5
6
5
6
7
8
4
5
6
SUM2
EXT. MUTE
1
2
3
4
5
6
C
US
CERTIFIED TO
CAN/CSA STD.E60065
3033118
SOURCE STATUS INPUTS
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM NETWORK
DIGITAL LINK
Any NuVo System zone output
can be wired to the LSA40 Local
Source Amplifier.
The connection from the LSA40 is made
through the NV-IG8LSA RJ45 port on the
back of the Control Pad terminated with
standard 568A. The connection at the
LSA40 requires the use of the Brown lead
for positive and Brown Stripe for
negative.
A two conductor wire is used as a voltage trigger
from the LSA40 the NuVo zone Control Pad. When the
zone is turned on, this allows to NuVo system audio
to pass to the zone speakers. When the zone is
turned off the internal amplifier of the LSA40 is
automatically engaged.
LSA40 Back
NV-I8GLSA
NuVoNet
MODEL:NV-LSA40
LOCAL SOURCE AMPLIFIER
+
+
-
-
AC Power Source
LSA40 Front
L
+
L
+
-
L
-
L
R+
R+
R
-
R
-
NuVo
Technologies LLC Cincinnati, Ohio USA
Designed In USA Made In China
WIRE STRIP 5/16” (8MM)
INPUT
SVR
1 of 9
3:09 PM
Follow the Day
drift
Edge of Tomorr
3:48
POWER
50 Watt AC
power adapter
supplied with
the LSA40S
1:28
NV-LSA40
Local Source Amplifier
MENU
Any stereo line level source
signal can be amplified through
the local source speakers using
the LSA40.
OK
33
Download from Www.Somanuals.com. All Manuals Search And Download.
NV-LSA40PD Local Source Power Distribution Hub (Fig. 54)
The LSA40PD Power Distribution Hub provides a compact method for distributing the necessary power to up to four LSA40 Local
Source Amplifiers from one central location. The LSA40PD distributes the power over 16 AWG two conductor speaker wire to each
of up to four individual LSA40 amplifiers. Connecting the LSA40 to the NuVo Control Pad and speakers is identical to the individual
zone installation diagramed on page 33, Fig. 53. Note that if you are using the NV-LSA40PD the needed SKU for each zone
amplifier is the LSA40 which is the local source amplifier with no power supply.
Fig. 54
SVR
of
Follow the Day
3:09 PM
1
9
drift
Edge of Tomorr
1:28
3:48
LSA40 Back
MENU
OK
MODEL:NV-LSA40
LOCAL SOURCE AMPLIFIER
+
-
L+
+
-
L
+
-
L
-
L
R+
R+
R
-
R
-
NuVo Technologies LLC Cincinnati, Ohio USA
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
Designed In USA Made In China
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
OUTPUT POWER
20W/6OHM X2
RS-232
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
WIRE STRIP 5/16” (8MM)
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
USE CNLY WITH 250V FUSE
ZONE
2
1
ZONE
5
2
ZONE
3
ZONE
4
ZONE
3
5
ZONE
2
6
ZONE 7&8
PROGRAM
1
1
6
2
3
1
2
4
1
3
SUM1
SYS ON
1
3
4
MODEL NV-I8DM
SIX SOURCE EIGHT ZONE
AUDIO DISTRIBUTION SYSTEM
CONNECT TO
NV-I8X
CONNECT TO
NV-I8EZP1
CONNECT TO
NV-I8X
120V
60Hz 500W
FUSE:T5
A
L
L
NuVo Technologies Cincinnati Ohio USA
USE NV-SLC1
CABLE
USE NV-NC1
CABLE
USE NV-SLC1
CABLE
R
R
R
R
R
CONFORMS TO
R
UL STD.6500
4
5
6
5
6
7
8
4
5
6
SUM2
EXT. MUTE
1
2
3
4
5
6
C
US
CERTIFIED TO
CAN/CSA STD.E60065
3033118
SOURCE STATUS INPUTS
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
EMITTER OUTPUTS
SYSTEM NETWORK
DIGITAL LINK
SVR
of
Follow the Day
3:09 PM
1
9
drift
Edge of Tomorr
1:28
3:48
MENU
LSA40 Back
OK
MODEL:NV-LSA40
LOCAL SOURCE AMPLIFIER
+
-
L+
+
-
L
+
-
L
-
L
R+
R+
R
-
R
-
NuVo Technologies LLC Cincinnati, Ohio USA
Designed In USA Made In China
WIRE STRIP 5/16” (8MM)
SVR
of
Follow the Day
3:09 PM
1
9
drift
Edge of Tomorr
1:28
3:48
MENU
LSA40 Back
OK
LSA40PD
Back
MODEL:NV-LSA40
LOCAL SOURCE AMPLIFIER
+
-
L+
+
LSA40PD Front
AC Power Source
-
L
+
-
L
-
L
R+
R+
R
-
R
-
NuVo Technologies LLC Cincinnati, Ohio USA
Designed In USA Made In China
WIRE STRIP 5/16” (8MM)
MODEL:NV-LSA40PD-DC
LOCAL SOURCE AMPLIFIER
28VDC 5A
+
+
ZONE
1
ZONE
3
-
-
+
+
ZONE
2
ZONE
4
-
-
DESIGNED IN USA
MADE IN CHINA
200 Watt AC
power adapter
included with
the LSA40PD
T
R
K
SVR
of
Follow the Day
3:09 PM
R
T
C
M
1
9
POWER
3033118
drift
Edge of Tomorr
1:28
3:48
MENU
OK
LSA40 Back
MODEL:NV-LSA40
LOCAL SOURCE AMPLIFIER
+
-
L+
+
-
L
+
-
L
-
L
R+
R+
R
-
R
-
NuVo Technologies LLC Cincinnati, Ohio USA
Designed In USA Made In China
WIRE STRIP 5/16” (8MM)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 55
NV-P2100 200-Watt Auxiliary Amplifier (Fig. 55)
NV-P2100 Amplifier
AUDIO
C
C
O
O
N
NTTRROLL
O
The P2100 is specifically designed for use with the NuVo
Systems’ lineouts. It can be used with either the fixed or
variable lineouts on the Grand Concerto amplifier. The
connection is made using either a 1/8 to 1/8 stereo patch
cable or a 1/8 stereo to RCA patch cable.
L
SENSITIVITY
1.0RMS
POWER
MODE
VOLTAGE
TRIGGER
OdBV
=
ON/OFF SWITCH
AUDIO AC/DC
3-30 VOLTS
AC OR DC
LEFT
RIGHT
INPUT
2
0
0
R
+6
-12
+6
-12
INPUT
OUTPUT
Grand Concerto Amplifier
VARIABLE
OUTPUT
VARIABLE
OUTPUT
VARIABLE
OUTPUT
OUTPUT POWER
40W/6OHM X2
OUTPUT POWER
40W/6OHM X2
OUTPUT POWER
40W/6OHM X2
TIP=L
RING=R
TIP=L
RING=R
TIP=L
RING=R
ZONE
6
ZONE
5
FIXED
OUTPUT
FIXED
OUTPUT
FIXED
OUTPUT
ZONE
2
1
ZONE
5
2
ZONE
CONNECT TO
NV-I8X
3
6
1
3
4
1
3
5
7
1
USE NV-SLC1
CABLE
There are two methods for triggering the P2100 from the
Grand Concerto outputs. One is to set the POWER MODE
switch on the P2100 to AUDIO (extreme left) position and
allow an incoming audio signal from the Grand Concerto
System to turn on the P2100. The second method is to place
the POWER MODE switch in the AC/DC (extreme right)
position. This will turn on the P2100 when the Grand
Concerto is on.
5
1
2
3
4
5
6
2
6
4
8
SOURCE INPUTS
SOURCE LINK
ZONE TRIGGER OUTPUTS
An additional feature of Grand Concerto is Zone-Specific
Triggers that will trigger the P2100 only when that zone is
turned on. Utilizing the voltage trigger requires a mono 1/8
patch cable from either the System ON output on the Grand
Concerto to the P2100 Voltage trigger input, or from the
specific Zone Trigger on the Grand Concerto to the Voltage
Trigger on the P2100, as shown in Fig. 55.
RS232 Interface
The RS232 port allows external two-way communication with
the Grand Concerto System. Home automation systems can
be set up to operate Grand Concerto. The RS232 protocol
document is available for download from the website
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Grand Concerto Specifications
Zones 1-6 Power Amplifier Outputs
Continuous Average Output Power
Two channels driven 30-20kHz @1% THD
Rated Distortion (1/2 power)
Rated Impedance
Zone Trigger Outputs
Output Power
Outputs
80W (40W x 2)
12V @ 50mA
8 (zones 1-8)
0.40%
6 Ohms
50+
Source Status
Output Power
Outputs
Damping Factor
Frequency Response
3-15 VDC
6 (Source 1-6)
20-20kHz 2dB
Zones 1-8 Preamplifier Outputs
Variable output
Fixed output
Power Requirements
Power Supply- North American
Power Supply- Export
0-600mV
600mV
120VAC/ 50Hz
240VAC/60Hz
Power Consumption all channels
driven to full-rated power
Power Consumption average
operating conditions
Power Consumption no signal
USA Safety Listing (UL 6500)
Canada Safety Listing (CAN/CSA E60065.00)
CE Listing/SEMKO (EN60065, EN55013,
EN55020, EN6100-3-2, EN6100-3-3/A1)
600VA (480W)
100VA (80W)
30VA (25W)
Impedance
600 Ohms
Source Inputs 1-6
input Impedance
Input Sensitivity for rated power
Input Overload
20K
300mV RMS
3V RMS
Emitter Outputs
Source Outputs
Sum Outputs
Output Drive Current
Output Drive Voltage
Compatible with single and dual emitters
6
2
Physical Specifications
Unit Size Millimeters
Unit Size Inches
Shipping Size Millimeters
Shipping Size Inches
Unit Weight Kilograms
Unit Weight Pounds
100mA
12V
95 x 430 x 340 (LWH)
3 3/4 x 17 x 13 3/8 (LWH)
600 x 475 x 380 (LWH)
23 5/8 x 18 3/4 x 15 (LWH)
System
System On (output)
External Mute (input)
9.4
20.6
15.5
34.0
12V @ 50mA
3-12V DC
Shipping Weight Kilograms
Shipping Weight Pounds
Serial Port
Baud Rate
Data Bits
Stop Bits
No Parity
57,600
8
1
NuVo reserves the right to change specifications without notice
No Flow Control
Grand Concerto Package Contents
NV-I8GMS Grand Concerto System
NV-I8GM Grand Concerto main amplifier
NV-I8GXS Grand Concerto Expander System
NV-I8GX Grand Concerto Expander Amplifier
6 NV-I8GCP Control Pads with white, ivory, almond
and black screwless trim plates
6 NV-I8GCP Control Pads with white, ivory, almond
and black screwless trim plates
1 NV-GRC1 Remote Control
6 NV-VEC Visible IR emitters
1 NV-GRC1 Remote Control
1 NV-SLC Audio Link cable
1 NV-I8EZP EZ Port connection hub
1 NV-NC1 3 meter network cable
1 pr. NV-REM Rack Ear Mounts
1 NV-DLC Digital Link cable
1 pr. NV-REM Rack Ear Mounts
1 NV-PC2NA Power Cable, 2 wire, North America
1 NV-PC2NA Power Cable, 2 wire, North America
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remedy
Symptom
Probable Cause
When the Control Pad is plugged in there is
a loud pop through the speakers and the
Control Pad does not work.
Improperly wired CAT5 cable.
Check that you are using the 568A or B
wiring standard (see section I: Crimping
CAT5 wire). The best way to know is to
use a CAT5 tester.
One of the zone Control Pads displays a
NuVoNet Not Detected message.
Zone CAT5 is plugged into the Accessory
jack on the back of the Control Pad instead
of the NuVoNet jack. Improperly wired
CAT5 Cable.
Check the CAT5 connection at the back of
the Control Pad. Plug the Control Pad
directly into the Network cable and into
the NuVoNet input on the Grand
Concerto.
The amplifier is plugged in and turned on,
but the STAND BY LED is not lit and none of
the system functions work.
This is most likely caused by a blown fuse
on the power supply.
The fuse is accessed at the AC plug on the
back of the amplifier. It requires a 4 amp
time delay fuse.
All of the system s Control Pads display a
NuVoNet Not Detected message.
The MCU card internal to the Grand
Concerto is damaged, or the data (blue
and blue stripe) conductors on one or more If the issue is a shorted CAT5, the
Remove all of the CAT5 connections from
the system and test cables one at a time.
of the CAT5 cables are shorted or not
making good contact in the RJ45
symptom will display when that cable is
connected to the system. A damaged
MCU must be replaced by NuVo.
With the Control Pads plugged in, the
POWER LED on the front of the amplifier will
not turn on.
One or more improperly wired CAT5 cables.
Make sure the amplifier is turned on. Test
that the POWER LED on the amplifier
turns on when the Network Cable is
unplugged. Next, unplug all the CAT5
cables from the Allport and plug them
back in one at a time until the bad
cable(s) is discovered.
The IR repeater does not properly control
the audio source equipment.
One or more of the IR emitters are not
properly placed over the IR receiver on the
audio source equipment, or the IR output
number on the Grand Concerto does not
correspond with the audio equipment you
are controlling.
Reposition the LED end of the emitter on
the face of the source equipment, so it
is flashing directly over that source s IR
receiver. Make sure the emitter plugged
into IR Output #1 is actually going to
source #1 , and so on for sources 2-6.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remedy
Symptom
Probable Cause
The IR repeater does not properly control
the audio source equipment.
The NuVo IR output is not set at the best
carrier frequency.
Within IR Library tab of the
Configurator Software, each library has
a Properties button. This button has a
drop down menu that lets you select
different carrier frequencies from
30kHz to 56kHz. This will default the
library to the selected frequency. Cable
and Satellite typically needs the 56kHz
setting.
The IR repeater does not properly control
the audio source equipment.
An External light source is interfering with
IR communication through the system.
In the Configurator Software (see pg.
19,IR Passthrough), or in the Advanced
Zone Setup menu (see pg. 27 Remote
Controls), at any Control Pad, you have
the ability by zone to Disable the IR
receiver. This will prevent direct
sunlight, or possibly, plasma and
fluorescent light from affecting IR
response through the other zone
receivers.
When downloading a Configuration to the
Grand Concerto Main amplifier, a board
not found error message appears on the
computer screen.
This occurs when the Grand Concerto is not
plugged into an AC power source, or a
faulty USB to RS232 conversion cable.
A communication error can be as simple
as not plugging the Grand Concerto in
prior to the download. Often the error is
also corrected by closing and reopening
the Configurator Software, or if you are
using a USB to RS232 cable for
communication, try a different cable. If
these do not correct the error, it could
be a faulty MCU board in the Grand
Concerto.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
NuVo Technologies LLC Hebron, Kentucky USA
I8G 0742
Download from Www.Somanuals.com. All Manuals Search And Download.
|
