NuTone Blower QT 9093 User Manual

READ & SAVE THESE INSTRUCTIONS!  
INSTALLATION INSTRUCTIONS  
Heat-A-Ventlite®  
HEATER  
SCREWS  
MODELS: QT-9093 SERIES  
IMPORTANT: DO NOT MOUNT OVER TUB  
OR IN SHOWER STALL ENCLOSURE.  
PRECAUTIONS  
Observe all requirements in this instruction sheet and all markings  
Caphpeecakrainllgoopnerthaetiounnsito. f the unit after installation has been completed.  
The heater housing must be grounded and the wiring must comply  
Twhitehflaalnl gloecoafl tehleecrotruicgahl-icnohdoeuss.ing MUST be flush with the finished  
pIflapslatestreorrmdarytewraialll,spuarfianct ebatoseasosrupraeinptroispseprraanydedabosnotlhuetewlyasllasfeorocpeeirliantgio,n.  
the inside of the housing must be masked off to prevent this material  
fTrohme sewnittecrhin(gfutrhneishhoeuds) imngu.st be wired in accordance with the  
HEATER  
SCREWS  
FIGURE 1  
wiring diagram.  
For installation in sloped ceilings up to 12/12 pitch.  
Ductwork must point up.  
13" DIA.  
PREPARATION  
Refer to Figure 1.  
1. Loosen two screws holding grille in place. Remove grille and set aside. Remove housing,  
switch assembly, hanger bar and mounting brackets from carton.  
2. Loosen four (4) screws holding heater power unit in place. Remove heater power unit and  
set aside.  
MOUNTING TO OPEN JOISTS IN NEW CONSTRUCTION  
1. Install hanger brackets in keyhole slots in housing. Insert hanger bar through bracket opposite  
blower vent.  
2. Refer to Figure 2. Position housing between joists with exhaust vent in desired direction.  
Secure side hanger brackets and ends of  
adjustable hanger bar to joists with screws or nails.  
If joist spacing is greater than 16" O.C., construct  
framing to support sides of housing,  
14" DIA.  
FIGURE 2  
(Refer to Figure 3). Position housing against joists  
and secure with wood screws through keyhole  
slots in housing.  
3. Loosen screws securing hanger brackets to  
housing and adjust height of housing so that  
bottom flange will be flush with finished ceiling.  
Tighten screws securely.  
4. Attach 4" round duct and run ductwork to the  
outside through wall or roof.  
FIGURE 3  
WIRING  
115-120 volts (20 amp circuit only), 12 gauge wire.  
1. Remove desired knockout from junction box and install a box connector (not provided).  
2. Refer to Figure 4. Run 120vAC supply wiring to wall switch box. Run wiring from wall switch box to  
heater. Five conductors plus ground are required for independent operation of all functions.  
3. When a thermostat or timer switch is used, connect at point marked “T” on Figure 4.  
4. Make wiring connections using wire nuts. Connect ground wire under ground screw in junction box.  
5. Push wiring back into junction box and install junction box cover being careful not to pinch wiring  
between cover and housing. Secure cover.  
FIGURE 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Moultrie Digital Camera D55IR User Manual
MTD Lawn Mower 111 030 User Manual
Murray Trimmer TM6100X5A User Manual
Nielsen Kellerman GPS Receiver ClearNav User Manual
Niles Audio Stereo Amplifier DPS 1 User Manual
Omnimount Indoor Furnishings LS31 User Manual
Omron Heart Rate Monitor HR 210 User Manual
Oricom Headphones C1000 18 GHz User Manual
Panasonic Air Conditioner KX TA624 User Manual
Partner Tech Lawn Mower PRT5043 User Manual