Nokia 3110 classic/Nokia 3109 classic User Guide
9200417
Issue 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Create a message..................................................................................16
Service commands..................................................................................20
E-mail messages...................................................................................21
Right selection key...............................................................................24
Transfer contact list.............................................................................26
Download from Www.Somanuals.com. All Manuals Search And Download.
C o n t e n t s
Appearance settings...............................................................................38
Record a video clip...............................................................................30
PTT channel types.................................................................................33
Switch PTT on and off.............................................................................33
Download from Www.Somanuals.com. All Manuals Search And Download.
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should
be road safety.
INTERFERENCE
All wireless devices may be susceptible to interference, which could affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the device off near medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in aircraft.
SWITCH OFF WHEN REFUELING
Do not use the device at a refueling point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the device where blasting is in progress.
USE SENSIBLY
Use only in the positions as explained in the product documentation. Do not touch the antenna areas unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect incompatible products.
WATER-RESISTANCE
Your device is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all important information stored in your device.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display
and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call until
given permission to do so.
About your device
The wireless device described in this guide is approved for use on the on the EGSM 900 and GSM 1800 and 1900 networks. Contact
your service provider for more information about networks.
When using the features in this device, obey all laws and respect local customs, privacy and legitimate rights of others, including
copyrights.
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified,
transferred, or forwarded.
Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device
on when wireless device use may cause interference or danger.
5
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
N e t w o r k s e r v i c e s
Network services
To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features
are not available on all networks; other networks may require that you make specific arrangements with your service provider before you can
use the network services. Your service provider can give you instructions and explain what charges will apply. Some networks may have
limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and
services.
Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear
on your device menu. Your device may also have a special configuration such as changes in menu names, menu order, and icons. Contact your
service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as multimedia messaging
(MMS), e-mail application, instant messaging, remote synchronization, and content downloading using the browser or MMS, require network
support for these technologies.
Shared memory
The following features in this device may share memory: gallery, contacts, text messages, multimedia messages, and instant messages, e-mail,
calendar, to-do notes, Java™ games and applications, and note application. Use of one or more of these features may reduce the memory
available for the remaining features sharing memory. Your device may display a message that the memory is full when you try to use a shared
memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing.
Enhancements
Practical rules about accessories and enhancements
•
•
•
•
Keep all accessories and enhancements out of the reach of small children.
When you disconnect the power cord of any accessory or enhancement, grasp and pull the plug, not the cord.
Check regularly that enhancements installed in a vehicle are mounted and are operating properly.
Installation of any complex car enhancements must be made by qualified personnel only.
6
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
General information
Access codes
Security code
The security code (5 to 10 digits) helps to protect your phone against unauthorized use. The preset code is 12345. You can
change the code, and set the phone to request the code. See "Security," p. 28.
PIN codes
The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help
to protect your SIM card against unauthorized use. See "Security," p. 28.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required for some functions.
The module PIN is required to access the information in the security module. See "Security module," p. 39.
The signing PIN is required for the digital signature. See "Digital signature," p. 39.
PUK codes
The personal unblocking key (PUK) code and the universal personal unblocking key (UPUK) code (8 digits) are required to change
a blocked PIN code and UPIN code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2 code. If the codes
are not supplied with the SIM card, contact your local service provider for the codes.
Barring password
The barring password (4 digits) is required when using the Call barring service. See "Security," p. 28.
Configuration setting service
To use some of the network services, such as mobile internet services, MMS, Nokia Xpress audio messaging, or remote internet
server synchronization, your device needs the correct configuration settings. For more information on availability, contact your
service provider, the nearest authorized Nokia dealer, or visit the support area on the Nokia website. See "Nokia
When you have received the settings as a configuration message and the settings are not automatically saved and activated,
Configuration sett. received is displayed.
To save the settings, select Show > Save. If required, enter the PIN code supplied by the service provider .
To discard the received settings, select Exit or Show > Discard.
Download content
You may be able to download new content (for example, themes) to your phone (network service).
Important: Use only services that you trust and that offer adequate security and protection against harmful software.
For the availability of different services, pricing, and tariffs, contact your service provider.
Software updates
Nokia may produce software updates that may offer new features, enhanced functions, or improved performance. You may be
able to request these updates through the Nokia Software Updater PC application. To update the device software, you need the
Nokia Software Updater application and a compatible PC with Microsoft Windows 2000 or XP operating system, broadband
internet access, and a compatible data cable to connect your device to the PC.
To get more information and to download the Nokia Software Updater application, visit www.nokia.com/softwareupdate or
your local Nokia website.
If software updates over the air are supported by your network, you may also be able to request updates through the device.
Downloading software updates may involve the transmission of large amounts of data through your service provider's network.
Contact your service provider for information about data transmission charges.
Make sure that the device battery has enough power, or connect the charger before starting the update.
Important: Use only services that you trust and that offer adequate security and protection against harmful software.
7
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t s t a r t e d
Nokia support
Support information
downloads, and services related to your Nokia product.
Configuration settings service
You may also download free configuration settings such as MMS, GPRS, e-mail, and other services for your device model at
Nokia PC Suite
Customer service
If you need to contact customer service, check the list of local Nokia Care contact centers at www.nokia.com/
Maintenance
For maintenance services, check your nearest Nokia service center at www.nokia.com/repair.
2.
Get started
All graphics show the Nokia 3110 classic phone.
Install SIM card and battery
Always switch the device off and disconnect the charger before removing the battery.
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider or
other vendor.
This device is intended for use with a BL-5C battery. Always use original Nokia batteries. See "Nokia battery authentication
The SIM card and its contacts can be easily damaged by scratches or bending, so be careful when handling, inserting, or removing
the card.
1. Slide the release button (1) to unlock and remove the back cover (2). Remove the
battery as shown (3).
2. Open the SIM card holder (4). Insert the SIM card (5) with the contact surface facing
down into the holder. Close the SIM card holder (6).
3. Observe the battery contacts (7), and insert the battery (8). Place the upper part
of the back cover on the device (9), and close it (10).
Insert a microSD card
Use only compatible microSD cards approved by Nokia for use with this device. Nokia uses approved industry standards for
memory cards, but some brands may not be fully compatible with this device. Incompatible cards may damage the card and
the device and corrupt data stored on the card.
1. Switch the device off, and remove the back cover and the battery of the device.
8
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
G e t s t a r t e d
2. Slide the memory card holder to unlock (1).
3. Open the card holder (2), and insert the memory card into the card holder with the contact surface
facing inwards (3).
4. Close the card holder (4), and slide the card holder to lock it (5).
5. Insert the battery, and attach the back cover to the device.
Charge the battery
Check the model number of any charger before use with this device. This device is intended for use when supplied with power
from the AC-3 or AC-4 charger.
Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The
use of any other types may invalidate any approval or warranty, and may be dangerous.
For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any
enhancement, grasp and pull the plug, not the cord.
1. Connect the charger to a wall socket.
2. Connect the lead from the charger to the socket on the bottom of your device.
If the battery is completely discharged, it may take a few minutes before the charging indicator appears
on the display or before any calls can be made.
The charging time depends on the charger used. Charging a BL-5C battery with the AC-3 charger takes
approximately 2 hours and 45 minutes while the device is in the standby mode.
Antenna
Your device has an internal antenna.
Note: As with any other radio transmitting device, do not touch the antenna unnecessarily
when the device is switched on. Contact with the antenna affects call quality and may cause
the device to operate at a higher power level than otherwise needed. To optimize antenna
performance and battery life, avoid contact with the antenna area when operating the
device.
Headset
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing.
Pay special attention to volume level if you connect any other headsets to the device.
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset
where it can endanger your safety.
Do not connect products that create an output signal as this may cause damage to the device. Do not connect any
voltage source to the Nokia AV Connector.
When connecting any external device or any headset, other than those approved by Nokia for use with this device, to
the Nokia AV Connector, pay special attention to volume levels.
Strap
1. Open the back cover.
9
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Y o u r d e v i c e
2. Hook a strap behind the clamp as shown in the picture (1) and close the back cover (2).
3.
Your device
Keys and parts
The Nokia 3110 classic phone is shown.
1 — Earpiece
2 — Display
3 — Left selection key
4 — Call key
5 — Infrared (IR) port
6 — Navi™ key: 4-way scroll key and middle selection key
7 — Right selection key
8 — End key
9 — Keypad
10 — Microphone
11 — Charger connector
12 — Nokia AV Connector (2.5 mm)
13 — Mini USB cable connector
14 — Volume down key
15 — Volume up key
16 — Power key
17 — Loudspeaker
18 — Camera lens (only Nokia 3110 classic)
Switch the device on and off
To switch the device on or off, press and hold the power key.
If the device prompts for a PIN or a UPIN code, enter the code (displayed as ****), and select OK.
The device may prompt you to set the time and date. Enter the local time, select the time zone of your location in terms of the
time difference with respect to Greenwich mean time (GMT), and enter the date. See "Time and date," p. 24.
When you switch on your device for the first time and the device is in the standby mode, you may be prompted to get the
configuration settings from your service provider (network service). For more information refer to Connect to service provider
Standby mode
When the device is ready for use, and you have not entered any characters, the device is in the standby mode.
10
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Y o u r d e v i c e
Display
1 — Signal strength of the cellular network
2 — Battery charge status
3 — Indicators
4 — Name of the network or the operator logo
5 — Clock
6 — Main screen
7 — The function of the left selection key is Go to or a shortcut to another function. See "Left selection key," p. 24.
8 — The function of the middle selection key is Menu.
9 — The function of the right selection key is Names or a shortcut to another function. See "Right selection key," p. 24. Operator
variants may have an operator-specific name to access an operator-specific website.
Power saving
Your device has a Power saver and a Sleep mode feature in order to save battery power in the standby mode when no key of
the device is pressed. These features may be activated. See "Display," p. 24.
Active standby
The active standby mode displays a list of selected device features and information that you can directly access.
To switch active standby on or off, select Menu > Settings > Display > Active standby > Active standby mode > On or
Off.
In the standby mode, scroll up or down to navigate in the list, and choose Select or View. The arrows indicate that further
information is available. To stop navigation, select Exit.
To organize and change the active standby mode, select Options and from the available options.
Shortcuts in the standby mode
To access the list of dialed numbers, press the call key once. Scroll to the number or name, and press the call key to call the
number.
To open the web browser, press and hold 0.
To call your voice mailbox, press and hold 1.
Use keys as a shortcut. See "My shortcuts," p. 24.
Indicators
unread messages
unsent, canceled, or failed messages
missed call
/
Your phone is connected to the IM service, and the availability status is online or offline.
instant messages received
The keypad is locked.
The phone does not ring for an incoming call or text message.
The alarm clock is activated.
The countdown timer is running.
The stopwatch is running in the background.
11
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
C a l l f u n c t i o n s
/
/
The phone is registered to the GPRS or EGPRS network.
A GPRS or EGPRS connection is established.
/
The GPRS or EGPRS connection is suspended (on hold).
A Bluetooth connection is active.
/
A push-to-talk connection is active or suspended.
If you have two phone lines, the second phone line is selected.
All incoming calls are diverted to another number.
The loudspeaker is activated, or the music stand is connected to the device.
Calls are limited to a closed user group.
The timed profile is selected.
/
/
A headset, handsfree, or loopset is connected to the device.
Flight mode
You can deactivate all radio frequency functions and still have access to offline games, calendar, and phone numbers.
Use the flight mode in radio sensitive environments—on board aircraft or in hospitals. When the flight mode is active,
is
shown.
Select Menu > Settings > Profiles > Flight > Activate or Personalise to activate or set up the flight mode.
To deactivate the flight mode, select any other profile.
Emergency call in flight mode - Enter the emergency number, press the call key, and select Yes when Exit flight profile? is
displayed. The phone attempts to make an emergency call.
Warning: With the flight profile you cannot make or receive any calls, including emergency calls, or use other features
that require network coverage. To make calls, you must first activate the phone function by changing profiles. If the
device has been locked, enter the lock code. If you need to make an emergency call while the device is locked and in
the flight profile, you may be also able to enter an official emergency number programmed in your device in the lock
code field and select 'Call'. The device will confirm that you are about to exit flight profile to start an emergency call.
Keypad lock (keyguard)
To prevent accidental keypresses, select Menu, and press * within 3.5 seconds to lock the keypad.
To unlock the keypad, select Unlock, and press * within 1.5 seconds. If Security keyguard is set to On, enter the security code
if requested.
To answer a call when keyguard is on, press the call key. When you end or reject the call, the keypad automatically locks.
When the keyguard is on, calls may be possible to the official emergency number programmed into your device.
Functions without a SIM card
Several functions of your device may be used without installing a SIM card (for example, the data transfer with a compatible PC
or another compatible device). Some functions appear dimmed in the menus and cannot be used.
4.
Call functions
Make a call
Number dialing
1. Enter the phone number, including the area code.
For international calls, press * twice for the international prefix (the + character replaces the international access code), enter
the country code, the area code without the leading 0, if necessary, and the phone number.
2. To call the number, press the call key. To adjust the volume in a call, press the volume key up or down.
3. To end the call or to cancel the call attempt, press the end key.
12
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
W r i t e t e x t
You can search for a name or phone number that you have saved in Contacts. See "Search for a contact," p. 22. Press the call
key to call the number.
To access the list of dialed numbers, press the call key once in the standby mode. To call the number, select a number or name,
and press the call key.
Dialing shortcuts
Assign a phone number to one of the number keys, 2 to 9. See "Dialing shortcuts," p. 23.
Call the number in one of the following ways:
Press a number key, then the call key.
OR
If Speed dialling is set to On, press and hold a number key until the call begins.
Enhanced voice dialing
You can make a phone call by saying the name that is saved in the contact list of the device.
Voice commands are language-dependent. Set the Voice recognition language before using voice dialing. See
Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely
upon voice dialing in all circumstances.
1. In the standby mode, press and hold the right selection key or the volume down key. A short tone sounds, and Speak
now is displayed.
2. Speak the name of the contact you want to dial clearly. If the voice recognition is successful, a list with matches is shown.
The device plays the voice command of the first match on the list. If it is not the correct command, scroll to another entry.
Using voice commands to carry out a selected device function is similar to voice dialing. See "Voice commands," p. 25.
Answer or reject a call
To answer an incoming call, press the call key. To end the call, press the end key.
To reject an incoming call, press the end key. To mute the ringing tone, select Silence.
To answer a waiting call during an active call (network service), press the call key. The first call is put on hold. To end the active
Options during a call
Many of the options that you can use during a call are network services. For availability, contact your service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Contacts, Menu, Lock keypad, Record, Voice clarity, Loudspeaker or Handset.
Network options are Answer or Reject, Hold or Unhold, New call, Add to conference, End call, End all calls, and the following:
•
•
•
•
•
Send DTMF — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer — to connect a call on hold to an active call and disconnect yourself
Conference — to make a conference call
Private call — to have a private discussion in a conference call
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
5.
Write text
Text modes
To enter text (for example, when writing messages) you can use traditional or predictive text input.
When you write text, press and hold Options to toggle between traditional text input, indicated by
, and predictive text
input, indicated by
. Not all languages are supported by predictive text input.
13
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
N a v i g a t e t h e m e n u s
The character cases are indicated by
,
, and
. To change the character case, press #. To change from the letter to number
mode, indicated by
, press and hold #, and select Number mode. To change from the number to the letter mode, press and
hold #.
To set the writing language, select Options > Writing language.
Traditional text input
Press a number key, 2 to 9, repeatedly until the desired character appears. The available characters depend on the selected
writing language.
If the next letter you want is located on the same key as the present one, wait until the cursor appears and enter the letter.
To access the most common punctuation marks and special characters, repeatedly press the number key 1 or press * to select
a special character.
Predictive text input
Predictive text input is based on a built-in dictionary to which you can also add new words.
1. Start writing a word, using the keys 2 to 9. Press each key only once for one letter.
2. When you finish writing the word and it is correct, to confirm it by adding a space, press 0.
If the word is not correct, press * repeatedly, and select the word from the list.
If the ? character is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the
dictionary, select Spell. Enter the word using traditional text input, and select Save. To write compound words, enter the
first part of the word, and press the scroll key right to confirm it. Write the last part of the word, and confirm the word.
3. Start writing the next word.
6.
Navigate the menus
The device offers you an extensive range of functions that are grouped into menus.
1. To access the menu, select Menu.
2. Scroll through the menu, and select an option (for example, Settings).
3. If the selected menu contains further submenus, select one (for example, Call).
4. If the selected menu contains further submenus, repeat step 3.
5. Select the setting of your choice.
6. To return to the previous menu level, select Back.
To exit the menu, select Exit.
To change the menu view, select Options > Main menu view > List, Grid, Grid with labels, or Tab.
To rearrange the menu, scroll to the menu to be moved, and select Options > Organise > Move. Scroll to where you want to
move the menu, and select OK. To save the change, select Done > Yes.
7.
Messaging
You can read, write, send, and save text, multimedia, e-mail, audio, and flash messages and postcards. All messages are organized
into folders.
Text messages
Your device supports the sending of text messages beyond the character limit for a single message. Longer messages are sent
as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks,
and characters from some language options, take up more space, limiting the number of characters that can be sent in a single
message.
With the short message service (SMS) you can send and receive text messages and receive messages that can contain pictures
(network service).
Before you can send any text message, you must save your message center number. See "Message settings," p. 20.
To check SMS e-mail service availability and to subscribe to the service, contact your service provider. You can save an e-mail
14
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
Write and send a text message
1. Select Menu > Messaging > Create message > Text message.
2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select
Add.
3. For an SMS e-mail, enter a subject in the Subject: field.
4. Write your message in the Message: field.
An indicator at the top of the display shows the total number of characters left and the number of messages needed for
sending. For example, 673/2 means that there are 673 characters left and that the message will be sent as a series of 2
messages.
Read and reply to a text message
1. To view a received message, select Show. To view it later, select Exit.
2. To read the message later, select Menu > Messaging > Inbox.
3. To reply to a message, select Reply and the message type.
4. Create the reply message.
is shown if you have unread messages in the inbox.
Multimedia messages
Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may
vary depending on the receiving device.
The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it
smaller so that it can be sent by MMS.
A multimedia message can contain text and objects such as images, sound clips, or video clips.
To check availability and to subscribe to the multimedia messaging service (MMS), contact your service provider. See "Message
Write and send a multimedia message
1. Select Menu > Messaging > Create message > Multimedia.
2. Create your message.
Your device supports multimedia messages that contain several pages (slides). A message can contain a calendar note and
a business card as attachments. A slide can contain text, one image, and one sound clip; or text and a video clip. To insert a
slide in the message, select New; or select Options > Insert > Slide. To insert a file in the message, select Insert.
3. To view the message before sending it, select Options > Preview.
4. To send the message, select Send.
5. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select
Add.
6. For an SMS e-mail, enter a subject in the Subject: field.
Write and send a multimedia plus message
Any content can be added to the multimedia plus message. Such content might be images, video clips, sound clips, business
cards, calendar notes, themes, streaming links, or even unsupported files (for example, files received with an e-mail).
1. Select Menu > Messaging > Create message > Multimedia plus.
2. Enter one or more phone numbers or e-mail addresses in the To: field. To retrieve a phone number or e-mail address, select
Add.
3. Enter a subject and write your message.
4. To insert a file in the message, select Insert or Options > Insert and the file type.
5. To view the message before sending it, select Options > Preview.
Read and reply to a multimedia message
Important: Exercise caution when opening messages. E-mail messages or multimedia message objects may contain
malicious software or otherwise be harmful to your device or PC.
15
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
1. To view the received message, select Show. To view it later, select Exit.
2. To view the whole message if the received message contains a presentation, select Play. To view the files in the presentation
or the attachments, select Options > Objects or Attachments.
3. To reply to the message, select Options > Reply and the message type.
4. Create the reply message.
Message sending process
To send the message, select Send. The phone saves the message in the Outbox folder, and the sending starts.
Note: Your device may indicate that your message was sent to the message center number programmed into your
device. Your device may not indicate whether the message is received at the intended destination. For more details
about messaging services, contact your service provider.
If an interruption occurs while the message is being sent, the phone tries to resend the message a few times. If these attempts
fail, the message remains in the Outbox folder. To cancel the sending of the messages in the Outbox folder, scroll to the desired
message, and select Options > Cancel sending.
Postcards
With the postcard messaging service (network service), create and send postcards that may contain an image and a greeting
text. The postcard is sent to the service provider using multimedia messaging. The service provider prints the postcard and
sends it to the postal address given with the message. MMS must be activated before this service can be used.
Before you can use the postcard service, you must subscribe to the service. To check the availability and costs and to subscribe
to the service, contact your service provider.
To send a postcard, select Menu > Messaging > Create message > Postcard. Fill in the address; mandatory editor fields
are marked by a *. Scroll to the image field, select Insert and an image from the gallery, or New image to insert a recent image;
then write your greeting text. To send the message, select Send.
Flash messages
Flash messages are text messages that are instantly displayed upon reception. Flash messages are not automatically saved.
Write a flash message
Select Menu > Messaging > Create message > Flash message. Enter the recipient’s phone number and write your message.
The maximum length of a flash message is 70 characters. To insert a blinking text into the message, select Options > Insert
blink char. to set a marker. The text after the marker blinks. To end the blinking text range, insert a second marker.
Read and reply to a flash message
A received flash message is indicated with Message: and a few words from the beginning of the message.
To read the message, select Read.
To extract numbers and addresses from the current message, select Options > Use detail.
To save the message, select Save and the folder in which you want to save it.
Nokia Xpress audio messaging
You can use the MMS to create and send an audio message in a convenient way. MMS must be activated before you can use
audio messages.
Create a message
2. Speak your message.
3. Enter one or more phone numbers in the To: field, or select Add to retrieve a number.
4. To send the message, select Send.
Listen to a message
To open a received audio message, select Play.
If more than one message is received, select Show > Play.
16
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
To listen to the message later, select Exit.
Memory full
When you receive a message, and the memory for the messages is full, Memory full. Unable to receive msgs. is displayed.
To delete old messages, select OK > Yes and the folder. Scroll to the desired message, and select Delete.
To delete more messages, select Mark. Mark all the messages you want to delete, and select Options > Delete marked.
Folders
The device saves received messages in the Inbox folder. Messages that have not yet been sent are saved in the Outbox folder.
To set the device to save the sent messages in the Sent items folder, select Menu > Messaging > Message settings >
General settings > Save sent messages.
To edit and send messages that you have written and saved in the drafts folder, select Menu > Messaging > Drafts.
You can move messages to the Saved items folder. To organize your Saved items subfolders, select Menu > Messaging >
Saved items.
To add a folder, select Options > Add folder.
To delete or rename a folder, scroll to the desired folder, and select Options > Delete folder or Rename folder.
To create a new template, save a message as a template, or access the template list, and select Menu > Messaging > Saved
items > Templates.
E-mail application
The e-mail application uses a packet data connection (network service) to allow you to access your e-mail account. This e-mail
application is different from the SMS e-mail function. To use the e-mail function on your device, you need a compatible e-mail
system.
You can write, send, and read e-mail with your device. Your device supports POP3 and IMAP4 e-mail servers. This application
does not support keypad tones.
Before you can send and retrieve any e-mail messages, you must obtain a new e-mail account or use your current account. To
check the availability of your e-mail account, contact your e-mail service provider.
Check your e-mail settings with your e-mail service provider. You may receive the e-mail configuration settings as a configuration
To activate the e-mail settings, select Menu > Messaging > Message settings > E-mail messages. See "E-mail
Setting wizard
The setting wizard starts automatically if no e-mail settings are defined in the phone.
To enter the settings manually, select Menu > Messaging > E-mail > Options > Manage accounts > Options > New.
The options for Manage accounts allow you to add, delete, and change the e-mail settings. Make sure that you have defined
the correct preferred access point for the operator. See "Configuration," p. 28.
The e-mail application requires an internet access point without a proxy. WAP access points normally include a proxy and do
not work with the e-mail application.
Write and send an e-mail
You can write your e-mail message before connecting to the e-mail service; or connect to the service first, then write and send
your e-mail.
1. Select Menu > E-mail > Write new e-mail.
2. If more than one e-mail account is defined, select the account from which you want to send the e-mail.
3. Enter the recipient’s e-mail address, write the subject, and enter the e-mail message. To attach a file from Gallery, select
Options > Attach file.
4. To send the e-mail message, select Send > Send now.
To save the e-mail in the Outbox folder to be sent later, select Send > Send later.
To edit or continue writing your e-mail later, select Options > Save as draft. The e-mail is saved in Outboxes > Drafts.
To send the e-mail later, select Menu > Messaging > E-mail > Options > Send now or Send/check e-mail.
17
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
Download e-mail
To download e-mail messages that have been sent to your e-mail account, select Menu > Messaging > E-mail > Check new
e-mail. If more than one e-mail account is defined, select the account from which you want to download the e-mail. The e-mail
application only downloads e-mail headers at first. Select Back > Inboxes, the account name, the new message, and
Retrieve to download the complete e-mail message.
To download new e-mail messages and to send e-mail that has been saved in the Outbox folder, select Options > Send/check
e-mail.
Read and reply to e-mail
Important: Exercise caution when opening messages. E-mail messages or multimedia message objects may contain
malicious software or otherwise be harmful to your device or PC.
1. Select Menu > Messaging > E-mail > Inboxes, the account name, and the desired message.
2. To reply to an e-mail, select Reply > Original text or Empty message. To reply to many, select Options > Reply to all.
Confirm or edit the e-mail address and subject; then write your reply.
3. To send the message, select Send > Send now.
E-mail folders
Your phone saves e-mail that you have downloaded from your e-mail account in Inboxes. Inboxes contains the following
folders: “Account name” for incoming e-mail, Archive for archiving e-mail, Custom 1—Custom 3 for sorting e-mail, Junk where
all spam e-mail is stored, Drafts for saving unfinished e-mail, Outbox for saving e-mail that has not been sent, and Sent
items for saving e-mail that has been sent.
To manage the folders and their e-mail content, select Options to view the available options of each folder.
Spam filter
The spam filter allows you to put specific senders on a black or white list. Black list sender messages are filtered toJunk. Unknown
and white list sender messages are downloaded into the account inbox.
To activate and define a spam filter, select Options > Spam filter > Settings in the main e-mail idle screen.
To blacklist a sender, select the e-mail message in the Inboxes folder and Options > Blacklist sender.
Instant messages
Note: Depending on your IM service, you may not have access to all of the features described in this guide.
With instant messaging (IM) (network service) you can send short, simple text messages to online users. You have to subscribe
to a service and register with the IM service you want to use. For more information about signing up for IM services, contact
your service provider.
To set the required settings for the IM service, use the option Connect. settings. See "Access," p. 18.
The icons and texts on the display may vary, depending on the IM service.
Access
Select Menu > Messaging > Instant messages. Instant messages may be replaced by another term depending on the
service provider. If more than one set of connection settings for IM service is available, select the one you want.
Select from the following options:
•
Login — to connect to the IM service. To set the phone to automatically connect to the IM service when you switch on the
phone, in the login session, select Automatic login: > On.
•
•
Saved convers. — to view, erase, or rename the conversations that you saved during an IM session
Connect. settings — to edit the settings needed for messaging and presence connection
Connect
To connect to the service, access the instant messages menu, select the IM service, if needed, and Login.
To disconnect from the IM service, select Options > Logout.
Sessions
When connected to the service, your status, as seen by others, is shown in a status line: Status: Online, My status: Busy, or
Status: App. off. To change your own status, select Change.
18
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
Below the status line there are three folders containing your contacts that show their status: Conversations, Online (), and
Offline (). To expand the folder, scroll to it, and select Expand (or scroll right).
To collapse the folder, select Collapse (or scroll left).
•
Conversations — shows the list of new and read instant messages or invitations to IM during the active IM session:
indicates a new group message
indicates a read group message
indicates a new instant message
indicates a read instant message
indicates an invitation
The icons and texts on the display depends on the IM service.
Online () — shows the number of contacts that are online
Offline () — shows the number of contacts that are offline
•
•
To start a conversation, expand the online or the offline folder, scroll to the contact with whom you want to chat, and select
Chat. To answer an invitation or reply to a message, expand the Conversations folder, scroll to the contact to whom you
want to chat, and select Open.
•
Groups > Public groups — List of bookmarks to public groups provided by the service provider (not visible if groups are not
supported by the network). To start an IM session with a group, scroll to a group, and select Join. Enter the screen name that
you want to use as your nickname in the conversation. When you have successfully joined the group conversation, you can
start a group conversation. You can create a private group. See "Groups," p. 19.
•
•
Search > Users or Groups — to search for other IM users or public groups on the network by phone number, screen name,
e-mail address, or name. If you select Groups, you can search for a group by a member in the group, group name, topic, or
ID.
Options > Chat or Join group — to start the conversation when you have found the user or the group that you want
Accept or reject an invitation
If you receive a new invitation, to read it, select Read. If more than one invitation is received, select an invitation and Open. To
join the private group conversation, select Accept, and enter the screen name you want to use as your nickname. To reject or
delete the invitation, select Options > Reject or Delete.
Read an instant message
If you receive a new message that is not a message associated with an active conversation, New instant message is displayed.
To read it, select Read. If more than one message is received, select a message and Open.
New messages received during an active conversation are held inInstant messages > Conversations. If you receive a message
from someone who is not in IM contacts, the sender ID is displayed. To save a new contact that is not in the phone memory,
select Options > Save contact.
Participate in a conversation
To join or start an IM session, write your message, and select Send.
If you receive a new message during a conversation from a person who is not taking part in the current conversation,
is
displayed, and the phone sounds an alert tone. Write your message, and select Send. Your message is displayed, and the reply
message is displayed below your message.
Add IM contacts
When connected to the IM service, in the IM main menu, select Options > Add contact > By mobile number, Enter ID
manually, Search from serv., or Copy from server (depending on the service provider). To start a conversation, scroll to a
contact, and select Chat.
Block or unblock messages
When you are in a conversation and want to block messages, select Options > Block contact.
To block messages from a specific contact in your contacts list, scroll to the contact in Conversations, and select Options >
Block contact > OK.
To unblock a contact, in the IM main menu, select Options > Blocked list. Scroll to the contact you want to unblock, and select
Unblock > OK.
Groups
You can use the public groups provided by the service provider or create your own private groups for an IM conversation.
19
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e s s a g i n g
You can bookmark public groups that your service provider may maintain. Connect to the IM service, and select Groups >
Public groups. Select a group and Join. If you are not in the group, enter your screen name as your nickname for the group.
To delete a group from your list, select Options > Delete group.
To search for a group, select Groups > Public groups > Search groups.
To create a private group, connect to the IM service, and, from the main menu, select Options > Create group. Enter the name
for the group and the screen name that you want to use as your nickname. Mark the private group members in the contacts
list, and write an invitation.
Voice messages
The voice mailbox is a network service to which you may need to subscribe. For more information, contact your service provider.
To call your voice mailbox, select Menu > Messaging > Voice messages > Listen to voice messages.
To enter, search for, or edit your voice mailbox number, select Voice mailbox number.
If supported by the network,
indicates new voice messages. To call your voice mailbox number, select Listen.
Info messages
You can receive messages on various topics from your service provider (network service). For more information, contact your
service provider.
Select Menu > Messaging > Info messages and from the available options.
Service commands
Service commands allow you to write and send service requests (USSD commands) to your service provider, such as activation
commands for network services.
To write and send the service request, select Menu > Messaging > Service commands. For details, contact your service
provider.
Delete messages
Delete a single message, all messages, or a folder.
To delete messages, select Menu > Messaging > Delete messages > By message to delete a single message, By folder to
delete all messages from a folder, or All messages.
SIM messages
SIM messages are specific text messages that are saved to your SIM card.
You can copy or move those messages from the SIM to the phone memory, but not vice versa.
To read SIM messages, select Menu > Messaging > Options > SIM messages.
Message settings
General settings
General settings are common for text and multimedia messages.
Select Menu > Messaging > Message settings > General settings and from the following options:
•
•
Save sent messages — Select Yes to save the sent messages in the Sent items folder.
Overwriting in Sent items — Select Allowed to overwrite old sent messages with the new ones when the message memory
is full. This setting is shown only if you select Save sent messages > Yes.
•
•
Font size — Select the font size used in messages.
Graphical smileys — Select Yes to set the device to replace character-based smileys with graphical ones.
Text messages
The text message settings affect the sending, receiving, and viewing of text and SMS e-mail messages.
Select Menu > Messaging > Message settings > Text messages and from the following options:
•
•
Delivery reports — Select Yes to ask the network to send delivery reports about your messages (network service).
Message centres — Select Add centre to set the phone number and name of the message center that is required for sending
text messages. You receive this number from your service provider.
•
Message centre in use — to select the message center in use.
20
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
C o n t a c t s
•
E-mail message centres — Select Add centre to set the phone numbers and name of the e-mail center for sending SMS e-
mail.
•
•
•
•
•
E-mail centre in use — to select the SMS e-mail message center in use
Message validity — to select the length of time for which the network attempts to deliver your message
Messages sent via — to select the format of the messages to be sent: Text, Paging, or Fax (network service)
Use packet data — Select Yes to set GPRS as the preferred SMS bearer.
Character support — Select Full to select all characters in the messages to be sent as viewed. If you select Reduced,
characters with accents and other marks may be converted to other characters.
Reply via same centre — Select Yes to allow the recipient of your message to send you a reply using your message center
(network service).
•
Multimedia messages
The message settings affect the sending, receiving, and viewing of multimedia messages.
You may receive the configuration settings for multimedia messaging as a configuration message. See "Configuration setting
Select Menu > Messaging > Message settings > Multimedia msgs. and from the following options:
•
•
•
•
•
Delivery reports — Select Yes to ask the network to send delivery reports about your messages (network service).
Image size (multimedia plus) — to set the image size in multimedia plus messages
Image size (multimedia) — to set the image size in multimedia messages
Default slide timing — to define the default time between slides in multimedia messages
Allow multimedia reception — Select Yes or No to receive or block the multimedia message. If you select In home
network, you cannot receive multimedia messages when outside your home network. The default setting of the multimedia
message service is generally In home network. The availability of this menu depends on your phone.
Incoming multi- media messages — to allow the reception of multimedia messages automatically, manually after being
prompted, or to reject the reception. This setting is not shown if Allow multimedia reception is set to No.
Allow adverts — to receive or reject advertisements. This setting is not shown if Allow multimedia reception is set to
No, or Incoming multi- media messages is set to Reject.
•
•
•
Configuration settings — Select Configuration to display the configurations that support multimedia messaging. Select a
service provider, Default, or Personal config. for multimedia messaging. Select Account and an MMS account contained in
the active configuration settings.
E-mail messages
The settings affect sending, receiving, and viewing e-mail. You may receive the settings as a configuration message. See
"Configuration setting service," p. 7. You can also manually enter the settings. See "Configuration," p. 28.
Select Menu > Messaging > Message settings > E-mail messages to display the options.
8.
Contacts
You can save names and phone numbers (contacts) in the device memory and in the SIM card memory.
The device memory can save contacts with additional details, such as various phone numbers and text items. You can also save
an image for a limited number of contacts.
The SIM card memory can save names with one phone number attached to them. The contacts saved in the SIM card memory
are indicated by
.
Save names and phone numbers
Names and numbers are saved in the used memory.
To save a name and phone number, select Menu > Contacts > Names > Options > Add new contact.
Save details
In the device memory you can save different types of phone numbers, a tone or a video clip, and short text items for a contact.
The first number you save is automatically set as the default number and is indicated with a frame around the number type
indicator (for example, ). When you select a name from contacts (for example, to make a call), the default number is used
unless you select another number.
Search for the contact to add a detail, and select Details > Options > Add detail.
21
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
C o n t a c t s
Select from the available options.
Settings
These settings define where the contact information is stored, how it is displayed, and how much memory remains.
Select Menu > Contacts > Settings and from the following options:
•
Memory in use — to select the SIM card or phone memory for your contacts. Select Phone and SIM to recall names and
numbers from both memories. In that case, when you save names and numbers, they are saved in the phone memory.
Contacts view — to select how the names and numbers in Contacts are displayed
Name display — to select whether the contact’s first or last name is displayed first
Font size — to set the font size for the list of contacts
•
•
•
•
Memory status — to view the free and used memory capacity
Groups
Select Menu > Contacts > Groups to arrange the names and phone numbers saved in the memory into caller groups with
different ringing tones and group images.
Search for a contact
Select Menu > Contacts > Names and scroll through the list of contacts, or enter the first characters of the name to search.
Copy or move contacts
To copy or move a contact between the SIM card memory and the phone memory, select Menu > Contacts > Names. Select
the contact to copy or move and Options > Copy contact or Move contact.
To copy or move several contacts, select the first contact to copy or move and Options > Mark. Mark the other contacts, and
select Options > Copy marked or Move marked.
To copy or move all contacts between the SIM card memory and the phone memory, select Menu > Contacts > Copy
contacts or Move contacts.
The SIM card memory can save names with one phone number attached to them.
Edit contact details
Search for the contact, and select Details.
To edit a name, number, or text item or to change the image, select Options > Edit.
To change the number type, scroll to the desired number, and select Options > Change type. To set the selected number as
the default number, select Options > Set as default.
Delete contacts
To delete a contact, search for the desired contact, and select Options > Delete contact.
To delete all the contacts and the details attached to them from the phone or SIM card memory, select Menu > Contacts >
Delete all contacts > From phone mem. or From SIM card.
To delete a number, text item, or an image attached to the contact, search for the contact, and select Details. Scroll to the
desired detail, and select Options > Delete and from the available options.
Synchronize all
Synchronize your calendar, contacts data, and notes with a remote internet server (network service). See "Synchronize from a
Business cards
You can send and receive a person’s contact information from a compatible device that supports the vCard standard as a business
card.
To send a business card, search for the contact, and select Details > Options > Send bus. card.
When you receive a business card, select Show > Save to save the business card in the phone memory. To discard the business
card, select Exit > Yes.
22
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
C a l l l o g
Dialing shortcuts
Your device can dial a phone number with one keypress. The number keys, 2 to 9, can have a phone number assigned to them.
To assign a phone number to a number key, select Menu > Contacts > Speed dials, and scroll to the number to assign as the
shortcut for Speed dialling.
Select Assign, or if a number has already been assigned to the key, select Options > Change.
Select Search and the contact to assign the shortcut. If Speed dialling is off, the phone asks whether you want to activate it.
To make a call using the shortcuts, press and hold the corresponding key. See "Dialing shortcuts," p. 13.
Info, service, and my numbers
Select Menu > Contacts and from one of these submenus:
•
•
•
Info numbers — to call the information numbers of your service provider if the numbers are included on your SIM card
(network service)
Service numbers — to call the service numbers of your service provider, if the numbers are included on your SIM card
(network service)
My numbers — to view the phone numbers assigned to your SIM card, if the numbers are included on your SIM card.
9.
Call log
The device registers your missed, received, and dialed calls if the network supports it and the device is switched on and within
the network service area.
To view the information on your calls, select Menu > Log > Missed calls, Received calls, or Dialled numbers.
To view your recent missed and received calls and the dialed numbers chronologically, select Call log. To view the contacts to
whom you most recently sent messages, select Message recipients.
To view the approximate information on your recent communications, select Menu > Log > Call duration, Packet data
counter, or Packet data conn. timer.
To view how many text and multimedia messages you have sent and received, select Menu > Log > Message log.
Note: The actual invoice for calls and services from your service provider may vary, depending on network features,
rounding off for billing, taxes, and so forth.
Note: Some timers, including the life timer, may be reset during service or software upgrades.
10.
Positioning
The network may send you a position request (network service). Contact your service provider to subscribe and to agree upon
the delivery of positioning information.
To accept or reject the position request, select Accept or Reject. If you miss the request, the phone automatically accepts or
rejects it according to what you have agreed with your network operator or service provider. The phone displays 1 missed
position request. To view the missed positioning request, select Show.
To view the information on the 10 most recent privacy notifications and requests or to delete them, select Menu > Log >
Positioning > Position log > Open folder or Delete all.
11.
Settings
Profiles
Your phone has various setting groups called profiles, for which you can customize the phone tones for different events and
environments.
Select Menu > Settings > Profiles, the desired profile, and from the following options:
•
•
Activate — to activate the selected profile
Personalise — to personalize the profile. Select the setting you want to change, and make the changes.
23
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S e t t i n g s
•
Timed — to set the profile to be active until a certain time (up to 24 hours) and set the end time. When the time set for the
profile expires, the previous profile that was not timed becomes active.
Themes
A theme contains elements for personalizing your device.
Select Menu > Settings > Themes and from the following options:
•
•
Select theme — to set a theme. A list of folders in Gallery opens. Open the Themes folder, and select a theme.
Theme downloads — to open a list of links to download more themes
Tones
You can change the tone settings of the selected active profile.
Select Menu > Settings > Tones. You can find the same settings in the Profiles menu. See "Profiles," p. 23.
To set the phone to only ring for calls from phone numbers that belong to a selected caller group, select Alert for.
Select Options > Save to save the settings or Cancel to leave the settings unchanged.
If you select the highest ringing tone level, the ringing tone reaches its highest level after a few seconds.
Display
Select Menu > Settings > Display and from the available options:
•
•
•
•
•
Wallpaper — to add the background image in the standby mode
Wallpaper — to add the background image in the Home screen
Active standby — to switch the active standby mode on or off and to organize and personalize the active standby mode
Standby mode font colour — to select the color for the texts in the standby mode
Navigation key icons — to display the icons of the current scroll key shortcuts in the standby mode when active standby is
off
•
•
Screen saver — to set your device to display a screen saver. To download more screen savers, select Graphic downloads.
To set the time after which the screen saver is activated, select Time-out.
Power saver — to save some battery power. The date and a digital clock are displayed when no function of the device is
used for a certain time.
•
•
•
•
Sleep mode — to save some battery power
Font size — to set the font size for messaging, contacts, and web pages
Operator logo — to set your device to display or hide the operator logo
Cell info display — to display the cell identity, if available from the network
Time and date
To change the clock type, time, time zone, and date settings, select Menu > Settings > Time and date > Time, Date, or
Auto-update of date & time (network service).
When traveling to a different time zone, select Menu > Settings > Time and date > Time > Time zone and the time zone
of your location in terms of the time difference with respect to Greenwich mean time (GMT) or coordinated universal time (UTC).
The time and date are set according to the time zone and enable your device to display the correct sending time of received
text or multimedia messages.
My shortcuts
With personal shortcuts you get quick access to often used functions of the device.
Left selection key
To select a function from the list, select Menu > Settings > My shortcuts > Left selection key.
If the left selection key is Go to to activate a function, in the standby mode, select Go to > Options and from the following
options:
•
•
Select options — to add a function to the shortcut list or to remove one
Organise — to rearrange the functions on your personal shortcut list
Right selection key
To select a function from the list, select Menu > Settings > My shortcuts > Right selection key.
24
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S e t t i n g s
Navigation key
To assign other device functions from a predefined list to the navigation key (scroll key), select Menu > Settings > My
shortcuts > Navigation key.
Voice commands
Call contacts and carry out device functions by speaking a voice command.
Voice commands are language-dependent, and you must set the Voice recognition language before using voice commands.
To select the device function to activate with a voice command, select Menu > Settings > My shortcuts > Voice
commands and a folder. Scroll to a function.
indicates that the voice tag is activated. To activate the voice tag, select Add.
To manage the voice commands, scroll to a device function, and select Options and from the following:
•
•
Edit or Remove — to change or deactivate the voice command of the selected function
Add all or Remove all — to activate or deactivate voice commands to all functions in the voice commands list
Infrared
You can set up the phone to send and receive data through its infrared (IR) port to or from a IRDA compatible phone or data
device.
Do not point the infrared (IR) beam at anyone's eye or allow it to interfere with other IR devices. This device is a Class 1 laser
product.
When sending or receiving data, ensure that the IR ports of the sending and receiving devices are pointing at each other and
that there are no obstructions between the devices.
To activate or deactivate the IR port of your phone, select Menu > Settings > Connectivity > Infrared.
If the data transfer is not started within 2 minutes after the activation of the IR port, the connection is cancelled and must be
started again.
IR connection indicator
•
When
is shown continuously, the IR connection is activated, and your phone is ready to send or receive data through its
IR port.
•
When
blinks, your phone is trying to connect to the other device, or a connection has been lost.
Bluetooth
Bluetooth wireless technology
Bluetooth technology allows you to connect the device to a compatible Bluetooth device within 10 meters (32 feet). Since devices
using Bluetooth technology communicate using radio waves, your device and the other devices do not need to be in direct line-
of-sight, although the connection can be subject to interference from obstructions such as walls or from other electronic devices.
This device is compliant with Bluetooth Specification 2.0 + EDR supporting the following profiles: generic access, network access,
generic object exchange, advanced audio distribution, audio video remote control, hands-free, headset, object push, file transfer,
dial-up networking, SIM access, and serial port. To ensure interoperability between other devices supporting Bluetooth
technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine
their compatibility with this device.
There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.
Features using Bluetooth technology, or allowing such features to run in the background while using other features, increase
the demand on battery power and reduce the battery life.
Set up a Bluetooth connection
Select Menu > Settings > Connectivity > Bluetooth and from the following options:
•
•
•
Bluetooth — Select On to activate the Bluetooth function.
indicates that Bluetooth is activated.
My phone's visibility — to define how your device is shown to other Bluetooth devices
Search for audio enhancements — to search for compatible Bluetooth audio devices. Select the device that you want to
connect to the phone.
•
•
Active devices — to check which Bluetooth connection is currently active
Paired devices — to search for any Bluetooth device in range. Select New to list any Bluetooth device in range. Select a
device and Pair. Enter an agreed Bluetooth passcode of the device (up to 16 characters) to pair the device to your device. You
25
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S e t t i n g s
must only give this passcode when you connect to the device for the first time. Your device connects to the other device, and
you can start data transfer.
•
My phone's name — to set the device name for Bluetooth connections
If you are concerned about security, turn off the Bluetooth function, or set My phone's visibility to Hidden. Always accept only
Bluetooth communication from others whom you trust.
Packet data
General packet radio service (GPRS) is a network service that allows mobile devices to send and receive data over an internet
protocol (IP)-based network.
To define how to use the service, select Menu > Settings > Connectivity > Packet data > Packet data connection and
from the following options:
•
When needed — to set the packet data connection to established when an application needs it. The connection will be
closed when the application is terminated.
•
Always online — to set the device to automatically connect to a packet data network when you switch the device on.
You can connect the device using Bluetooth wireless technology or USB data cable connection to a compatible PC and use the
device as a modem to enable GPRS connectivity from the PC.
To define the settings for connections from your PC, select Menu > Settings > Connectivity > Packet data > Packet data
settings > Active access point, and activate the access point you want to use. Select Edit active access point > Alias for
access point, enter a name to change the access point settings, and select OK. Select Packet data access point, enter the
access point name (APN) to establish a connection to a network, and select OK.
Establish an internet connection by using your phone as a modem. See "Nokia PC Suite," p. 40. If you have set the settings
both on your PC and on your device, the PC settings are used.
Data transfer
Synchronize your calendar, contacts data, and notes with another compatible device (for example, a mobile device), a compatible
PC, or a remote internet server (network service).
Your device allows data transfer with a compatible PC or another compatible device when using the device without a SIM card.
Transfer contact list
To copy or synchronize data from your device, the name of the device and the settings must be in the list of transfer contacts.
If you receive data from another device (for example, a compatible mobile device), the corresponding transfer contact is
automatically added to the list, using the contact data from the other device. Server sync and PC sync are the original items
in the list.
To add a new transfer contact to the list (for example, a mobile device), select Menu > Settings > Connectivity > Data
transfer > Options > Add contact > Phone sync or Phone copy, and enter the settings according to the transfer type.
To edit the copy and synchronize settings, select a contact from the transfer contact list and Options > Edit.
To delete a transfer contact, select it from the transfer contact list and Options > Delete.
Data transfer with a compatible device
For synchronization use Bluetooth wireless technology or a cable connection. The other device must be activated for receiving
data.
To start data transfer, select Menu > Settings > Connectivity > Data transfer and the transfer contact from the list other
than Server sync or PC sync.
According to the settings, the selected data is copied or synchronized.
Synchronize from a PC
To synchronize data from calendar, notes, and contacts, install the Nokia PC Suite software of your device on a compatible PC.
Use Bluetooth wireless technology or a USB data cable to connect your device with the PC and start the synchronization from
the PC.
Synchronize from a server
To use a remote internet server, subscribe to a synchronization service. For more information and the settings required for this
service, contact your service provider. You may receive the settings as a configuration message. See "Configuration setting
To start the synchronization from your device, select Menu > Settings > Connectivity > Data transfer > Server sync.
Synchronizing for the first time or after an interrupted synchronization may take up to 30 minutes to complete.
26
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S e t t i n g s
USB data cable
You can use the USB data cable to transfer data between the device and a compatible PC or a printer supporting PictBridge. You
can also use the USB data cable with Nokia PC Suite.
To activate the device for data transfer or image printing, connect the data cable. Confirm "USB data cable connected. Select
mode." and select from the following options:
•
•
•
Nokia mode — to use the cable for PC Suite
Printing & media — to use the device with a PictBridge compatible printer or with your compatible PC
Data storage — to connect to a PC that does not have Nokia software and use the device as a data storage device
To change the USB mode, select Menu > Settings > Connectivity > USB data cable and the desired USB mode.
Call
Select Menu > Settings > Call and from the following options:
•
Call divert — to divert your incoming calls (network service). You may not be able to divert your calls if some call barring
functions are active. See "Security," p. 28.
•
•
Voice clarity — Select Active to enhance speech intelligibility especially in noisy environments.
Anykey answer — Select On to answer an incoming call by briefly pressing any key, except the power key, the left and right
selection keys, or the end key.
•
•
Automatic redial — Select On to make a maximum of 10 attempts to connect the call after an unsuccessful call attempt.
Speed dialling — Select On to dial the names and phone numbers assigned to the number keys 2 to 9 by pressing and
holding the corresponding number key.
•
Call waiting — Select Activate to have the network notify you of an incoming call while you have a call in progress (network
service). See "Answer or reject a call," p. 13.
•
•
Summary after call — Select On to briefly display the approximate duration after each call.
Send my caller ID — Select Yes to show your phone number to the person you are calling (network service). To use the
setting agreed upon with your service provider, select Set by network.
•
Line for outgoing calls — to select the phone line 1 or 2 for making calls if supported by your SIM card (network service)
Phone
Select Menu > Settings > Phone and from the following options:
•
Language settings — To set the display language of your device, select Phone language. Automatic selects the language
according to the information on the SIM card. To select the USIM card language, select SIM language. To set a language for
Security keyguard — To set the device to ask for the security code when you unlock the keyguard. Enter the security code,
and select On.
•
•
Automatic keyguard — to lock the keypad automatically after a preset time delay when the device is in the standby mode
and no function of the device has been used. Select On, and set the time.
•
•
Welcome note — to write the note that is shown when the device is switched on
Flight query — The device asks every time when it is switched on whether you want to use the flight profile. With the flight
profile, all radio connections are switched off. The flight profile should be used in areas sensitive to radio emissions.
Phone updates — to receive software updates from your service provider (network service). This option may not be available,
depending on your device. See "Software updates over the air," p. 28.
•
•
Operator selection — Select Automatic to set the device to automatically select one of the cellular networks available in
your area. With Manual you can select a network that has a roaming agreement with your service provider.
•
•
•
Help text activation — to select whether the device shows help texts
Start-up tone — The device plays a tone when it is switched on.
Enhancements
This menu or the following options are shown only if the device is or has been connected to a compatible mobile enhancement.
Select Menu > Settings > Enhancements. Select an enhancement, and depending on the enhancement, from the following
options:
•
•
Default profile — to select the profile that you want to be automatically activated when you connect to the selected
enhancement
Automatic answer — to set the device to answer an incoming call automatically after 5 seconds. If Incom. call alert: is set
to Beep once or Off, automatic answer is off.
•
•
Lights — to set the lights permanently On. Select Automatic to set the lights on for 15 seconds after a keypress.
Text phone — Select Use text phone > Yes to use this setting instead of headset or loopset settings.
27
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S e t t i n g s
Configuration
You can configure your device with settings that are required for certain services. Your service provider may also send you these
Select Menu > Settings > Configuration and from the following options:
•
Default configuration settings — to view the service providers saved in the device. To set the configuration settings of
the service provider as default settings, select Options > Set as default.
•
•
Activate default in all applications — to activate the default configuration settings for supported applications
Preferred access point — to view the saved access points. Scroll to an access point, and select Options > Details to view
the name of the service provider, data bearer, and packet data access point or GSM dial-up number.
•
•
Connect to service provider support — to download the configuration settings from your service provider
Device manager settings — to allow or prevent the device from receiving software updates. This option may not be
available, depending on your device. See "Software updates over the air," p. 28.
•
Personal configuration settings — to manually add new personal accounts for various services and to activate or delete
them. To add a new personal account if you have not added any, select Add new; otherwise, select Options > Add new.
Select the service type, and select and enter each of the required parameters. The parameters differ according to the selected
service type. To delete or activate a personal account, scroll to it, and select Options > Delete or Activate.
Security
When security features that restrict calls are in use (such as call barring, closed user group, and fixed dialing), calls may be
possible to the official emergency number programmed into your device.
Select Menu > Settings > Security and from the following options:
•
•
•
•
PIN code request and UPIN code request — to set the device to ask for your PIN or UPIN code every time the device is
switched on. Some SIM cards do not allow the code request to be turned off.
PIN2 code request — to select whether the PIN2 code is required when using a specific device feature which is protected
by the PIN2 code. Some SIM cards do not allow the code request to be turned off.
Call barring service — to restrict incoming calls to and outgoing calls from your device (network service). A barring password
is required.
Fixed dialling — to restrict your outgoing calls to selected phone numbers if this function is supported by your SIM card.
When the fixed dialing is on, GPRS connections are not possible except while sending text messages over a GPRS connection.
In this case, the recipient’s phone number and the message center number must be included in the fixed dialing list.
Closed user group — to specify a group of people whom you can call and who can call you (network service)
Security level — Select Phone to set the device to ask for the security code whenever a new SIM card is inserted into the
device. If you select Memory, the device asks for the security code when the SIM card memory is selected, and you want to
change the memory in use.
•
•
•
•
•
Access codes — to change the security code, PIN code, UPIN code, PIN2 code, or barring password
Code in use — to select whether the PIN code or UPIN code should be active
Authority certificates or User certificates — to view the list of the authority or user certificates downloaded into your
device. See "Certificates," p. 39.
•
Security module settings — to view Security module details, activate Module PIN request, or change the module PIN
and signing PIN. See "Access codes," p. 7.
Software updates over the air
Warning: If you install a software update, you cannot use the device, even to make emergency calls, until the
installation is completed and the device is restarted. Be sure to back up data before accepting installation of an update.
Your service provider may send device software updates over the air directly to your device (network service). This option may
not be available, depending on your device.
Software update settings
To allow or disallow software updates, select Menu > Settings > Configuration > Device manager settings > Service
provider software updates and the following options:
•
•
•
Always allow — to perform all software downloads and updates automatically
Always reject — to reject all software updates
Confirm first — to perform software downloads and updates only after your confirmation (default setting)
Request a software update
Select Menu > Settings > Phone > Phone updates to request available software updates from your service provider. Select
Current software details to display the current software version and check whether an update is needed. Select Download
phone software to download and install a software update. Follow the instructions on the display.
28
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
O p e r a t o r m e n u
Install a software update
If the installation was canceled after the download, select Install software update to start the installation.
The software update may take several minutes. If there are problems with the installation, contact your service provider.
Restore factory settings
To reset some of the menu settings to their original values, select Menu > Settings > Restore factory sett.. Enter the security
code.
The names and phone numbers saved in Contacts are not deleted.
12.
Operator menu
This menu lets you access a portal to services provided by your network operator. The name and the icon depend on the operator.
For more information contact your network operator. The operator can update this menu with a service message. See "Service
13.
Gallery
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied,
modified, transferred or forwarded.
Manage images, video clips, music files, themes, graphics, tones, recordings, and received files. These files are stored in the
device memory or an attached memory card and may be arranged in folders.
Your device supports an activation key system to protect acquired content. Always check the delivery terms of any content and
activation key before acquiring them, as they may be subject to a fee.
Folders and files
To see the list of folders, select Menu > Gallery.
To view the list of files in a folder, select a folder and Open.
To see the available options of a folder or a file, select a folder or a file and Options.
To view the folders of the memory card when moving a file, scroll to the memory card, and press the scroll key right.
Print images
Your device supports Nokia XPressPrint to print images that are in the .jpeg format.
To connect your device to a compatible printer, use a data cable or send the image by Bluetooth to a printer supporting Bluetooth
technology. See "PC connectivity," p. 40.
Select the image you want to print and Options > Print.
Memory card
Warning: Keep all memory cards out of the reach of small children.
Use a memory card to store your multimedia files such as video clips, music tracks, sound files, images, and messaging data.
Some of the folders in Gallery with content that the device uses (for example, Themes) may be stored on the memory card.
Format the memory card
Some supplied memory cards are preformatted; others require formatting. Consult your retailer to find out if you must format
the memory card before you can use it. When you format a memory card, all data on the card is permanently lost.
To format a memory card, select Menu > Gallery or Applications, the memory card folder
, and Options > Format mem.
card > Yes.
When formatting is complete, enter a name for the memory card.
29
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e d i a
Lock the memory card
Set a password to lock your memory card against unauthorized use.
Selectthememorycardfolder
andOptions > Setpassword. Thepasswordcanbeuptoeightcharacterslong. Thepassword
is stored in your device, and you do not have to enter it again while you are using the memory card on the same device. If you
want to use the memory card on another device, you are asked for the password.
To delete the password, select Options > Delete password.
Check memory consumption
Check the memory consumption of different data groups and the available memory to install new applications or software on
your memory card.
Select the memory card
and Options > Details.
14.
Media
Camera and video
This feature is available with the Nokia 3110 classic phone.
Take images or record video clips with the built-in camera.
Take a picture
To use the still picture function, select Menu > Media > Camera or if the video function is on, scroll left or right.
To take a picture in landscape format, hold the device in a horizontal position. To zoom in and out in the camera mode, scroll
up and down or press the volume keys.
To take a picture, select Capture. The device saves the pictures on the memory card, if available, or on the phone memory.
Select Options to set Night mode on if the lighting is dim, Self-timer on to activate the self-timer, or Img. sequence on to
take pictures in a fast sequence. With the highest picture size setting, three pictures are taken in a sequence; with other size
settings, five pictures are taken.
Select Options > Settings > Image preview time and a preview time to display the taken pictures. During the preview time,
select Back to take another picture or Send to send the picture as a multimedia message.
Your device supports a picture capture resolution up to 1280 x 1024 pixels.
Record a video clip
To activate the video function, select Menu > Media > Video; or if the camera function is on, scroll left or right.
To start the video recording, select Record; to pause the recording, select Pause; to resume the recording, select Continue; to
stop the recording, select Stop.
The device saves the video clips on the memory card, if available, or in the device memory.
Camera and video options
To use a filter, select Options > Effects > False colours, Greyscale, Sepia, Negative, or Solarise.
To adapt the camera to the light conditions, select Options > White balance > Auto, Daylight, Tungsten, or Fluorescent.
To change other camera and video settings and to select the image and video storage, select Options > Settings.
Media player
View, play, and download files, such as images, audio, video, and animated images; or view compatible streaming videos from
a network server (network service).
Select Menu > Media > Media player > Open Gallery, Bookmarks, Go to address, or Media downloads to select or
download media.
Select Menu > Media > Media player > FF/Rew interval to set the length of the interval for fast forward or rewind.
Configuration for a streaming service
You may receive the configuration settings required for streaming as a configuration message from the service provider. See
"Configuration setting service," p. 7. You can also enter the settings manually. See "Configuration," p. 28.
30
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
M e d i a
To activate the settings, do the following:
1. Select Menu > Media > Media player > Streaming sett. > Configuration.
2. Select a service provider, Default, or Personal config. for streaming.
3. Select Account and a streaming service account contained in the active configuration settings.
Music player
Your device includes a music player for listening to music tracks or other MP3 or AAC sound files that you have downloaded from
the web or transferred to the device with Nokia PC Suite. See "Nokia PC Suite," p. 40.
Music files stored in the music folder in the device memory or on the memory card are automatically detected and added to the
music library during the startup of the device.
To open the music player, select Menu > Media > Music player.
Play music tracks
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing. Do
not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.
Operate the music player with the virtual keys on the display.
When you open Music player, the details of the first track on the default track list are shown. To start playing, select
To adjust the volume level, use the volume keys of the device.
.
To pause the playing, select
To skip to the next track, select
.
. To skip to the beginning of the previous track, select
twice.
To fast forward the current track, select and hold
. To rewind the current track, select and hold
. Release the key at the
position you want.
To stop the music player, press and hold the end key.
Music player options
In the music player menu, select from the following options:
•
•
Show tracks — View all available tracks of the active track list and play the desired track. To play a track, scroll to the desired
track, and select Play.
Music library — View all available tracks ordered according to Artists, Albums, Genres, Composers, or Track lists. Select
Update libr. to refresh the lists. To find track lists generated with the Nokia Music Manager, select Track lists > My
tracks.
•
Play options — Select Random to play the tracks on the track list in random order. Select Repeat to play the current track
or the entire track list repeatedly.
•
•
•
•
•
•
•
•
Media equaliser — to select or define an equalizer setting
Add to Favourites — to add the current track to the favorite track list
Play via Bluetooth — to connect and play the tracks on an audio accessory using Bluetooth technology
Use tone — Set the currently played music track, for example, as a ringing tone.
Send — to send the current track by a multimedia message or using Bluetooth technology
Web page — to access a web page associated with the currently played track, which is dimmed if no web page is available.
Music downloads — to connect to a web service
Memory status — to view the free and used memory capacity
Radio
The FM radio depends on an antenna other than the wireless device antenna. A compatible headset or enhancement
needs to be attached to the device for the FM radio to function properly.
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing. Do
not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.
This feature is available with the Nokia 3110 classic phone.
Select Menu > Media > Radio.
To use the graphical keys
,
,
, or
on the display, scroll left or right to the desired key, and select it.
or . To change the radio frequency in 0.05 MHz steps, briefly press
Save radio frequencies
1. To start the search, select and hold
or
.
31
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
P u s h t o t a l k
2. To save a frequency to a memory location, 1 to 9, press and hold the corresponding number key. To save a frequency to a
memory location from 10 to 20, press briefly 1 or 2, and press and hold the desired number key, 0 to 9.
3. Enter the name of the radio station.
Listen to the radio
Select Menu > Media > Radio. To scroll to the desired frequency, select
or , or press the headset key. To select a radio
station, briefly press the corresponding number keys. To adjust the volume, press the volume keys.
Select from the following options:
•
•
Switch off — to turn off the radio
Loudspeaker or Headset — to listen to the radio using the loudspeaker or headset. Keep the headset connected to the
device. The lead of the headset functions as the radio antenna.
•
•
Mono output or Stereo output — to listen to the radio in monophonic sound or in stereo
Stations — to select the list of saved stations. To delete or rename a station, scroll to the desired station, and select
Options > Delete station or Rename.
•
•
•
•
•
Search all stations — to automatically search the available stations at your location
Set frequency — to enter the frequency of the desired radio station
Station directory — to access a website with a list of radio stations
Visual Radio — to start visual radio manually
Enable visual serv. — Select Automatically to set whether Visual Radio (network service) automatically starts when you
turn on the radio. Some radio stations may send text or graphical information that you can view using the Visual Radio
application. To check the availability and costs, contact your service provider.
When an application using a packet data or HSCSD connection sends or receives data, it may interfere with the radio.
Voice recorder
Record speech, sound, or an active call, and save them in Gallery. This is useful when recording a name and phone number to
write down later.
Record sound
1. Select Menu > Media > Recorder. To use the graphical keys
,
, or
on the display, scroll left or right to the desired
key, and select it.
2. To start the recording, select . To start the recording during a call, select Options > Record. While recording a call, all
parties to the call hear a faint beeping. When recording a call, hold the device in the normal position near to your ear. To
pause the recording, select
.
3. To end the recording, select . The recording is saved in Gallery > Recordings.
Select from the following Options:
•
•
•
Play last recorded — to listen to the latest recording
Send last recorded — to send the last recording
Recordings list — Select Recordings to see the list of recordings in Gallery
Equalizer
Control the sound when using the music player by amplifying or diminishing frequency bands.
Select Menu > Media > Equaliser.
To activate a set, scroll to one of the equalizer sets, and select Activate.
To view, edit, or rename a selected set, select Options > View, Edit, or Rename.
Not all sets can be edited or renamed.
Stereo widening
Stereo widening enhances the audio output of the device when you are using a stereo headset by enabling a wider stereo sound
effect.
To change the setting, select Menu > Media > Stereo widening.
15.
Push to talk
Push to talk (PTT) is a two-way radio service available over a GPRS cellular network (network service).
32
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
P u s h t o t a l k
You can use PTT to have a conversation with one person or with a group of people (channel) having compatible devices. While
you are connected to the PTT service, you can use the other functions of the device.
To check availability, costs, additional features and to subscribe to the service, contact your service provider. Roaming services
may be more limited than for normal calls. This feature may not be available, depending on your phone.
Before you can use the PTT service, you must define the required PTT service settings. See "PTT settings," p. 34. See
PTT channels
PTT channel types
A PTT channel comprises a group of people (for example, friends or a work team) who joined the channel after they were invited.
When you call a channel, all members joined to the channel hear the call simultaneously.
In a Public channel, every channel member can invite other persons; in a Private channel, only the channel creator can invite
others.
You can set the status of each channel to Active or Inactive.
The number of active channels and the number of members per channel is limited. Contact your service provider for details.
Create a channel
To add a channel, select Menu > Push to talk > Add channel, and enter the settings in the form fields.
To send an invitation to the channel, select Yes. To send further invitations, select Menu > Push to talk > Channel list, a
channel, and Options > Send invitation.
Switch PTT on and off
To connect to the PTT service, select Menu > Push to talk > Switch PTT on. indicates the PTT connection. indicates that
the service is temporarily unavailable. If you have added channels to the phone, you are automatically joined to the active
channels.
To disconnect from the PTT service, select Switch PTT off.
You may assign a default function to the PTT (volume up) key to open the channel list, the contacts list, or a single channel or
contact. See "PTT settings," p. 34.
Make and receive a PTT call
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
To make a channel call, a one-to-one call, or a call to multiple recipients, you must hold the PTT (volume up) key as long as you
talk. To listen to the response, release the PTT (volume up) key.
Check the login status of your contacts in Menu > Push to talk > Contacts list:
- person available,
- person unknown,
- person does not want to be disturbed, but can receive callback request,
- person has PTT switched off.
This service depends on your network operator and is only available for subscribed contacts. To subscribe a contact, select
Options > Subscribe contact, or if one or more contacts are already marked, Subscribe marked.
Make a channel call
To make a call to a channel, select Channel list in the PTT menu, scroll to the desired channel, and press and hold the PTT
(volume up) key.
Make a one-to-one call
To start a one-to-one call, select Menu > Contacts > Names, or Menu > Push to talk > Callback inbox, Channel list, or
Contacts list. Select a contact, a member, or a nickname, and press and hold the PTT (volume up) key.
Make a PTT call to multiple recipients
You can select multiple PTT contacts from the contact list.
1. Select Menu > Push to talk > Contacts list, and mark the desired contacts.
2. Press and hold the PTT (volume up) key to start the call. The participating contacts are shown on the display as soon as they
join the call.
3. Press and hold the PTT (volume up) key to talk to them. Release the PTT (volume up) key to hear the response.
4. Press the end key to terminate the call.
33
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
A p p l i c a t i o n s
Receive a PTT call
A short tone notifies you of an incoming PTT call, which you can accept or reject.
When you press and hold the PTT (volume up) key while the caller is talking, you hear a queuing tone, and Queuing is displayed.
Wait for the other person to finish; then you can talk immediately.
Callback requests
Send a callback request
If you make a one-to-one call and do not get a response, you can send a callback request from following lists:
•
•
Menu > Contacts > Names
Menu > Push to talk > Callback inbox, Channel list, or Contacts list
Select a contact, a member, or a nickname and Options > Send PTT callback.
Respond to a callback request
When someone sends you a callback request, Callback request received is displayed in the standby mode. To open the Callback
inbox, select View. The list of nicknames of the persons who have sent you callback requests is shown. To make a one-to-one
call, select the desired request, and press and hold the PTT (volume up) key.
Add a one-to-one contact
You can save the names of persons to whom you often make one-to-one calls in the following ways:
•
To add a PTT address to a name in Contacts, search for the desired contact, and select Details > Options > Add detail >
PTT address. A contact appears in the PTT contact list only if you enter a PTT address.
•
•
To add a contact to the PTT contacts list, select Menu > Push to talk > Contacts list > Options > Add contact.
To add a contact from the channel list, connect to the PTT service, select Channel list, and scroll to the desired channel. Select
Members, scroll to the member whose contact information you want to save, and select Options.
•
To add a new contact, select Save as. To add a PTT address to a name in Contacts, select Add to contact.
PTT settings
Select Menu > Push to talk > PTT settings and from the following options:
•
1 to 1 calls — Select On to allow the reception of incoming one-to-one calls. To set the device to first notify you of incoming
one-to-one calls with a ringing tone, select Notify.
•
PTT key default function — to set the PTT (volume up) key to one of the following functions: Open contact list, Open
channel list, or Call contact/group. Select a contact, a group, or Call PTT channel; and select a channel. When you press
and hold the PTT (volume up) key, the selected function is performed.
•
•
•
•
Show my login status — to enable or disable the sending of the login status
PTT status in startup — Select Yes or Ask first to automatically connect to the PTT service when you switch the device on.
Push to talk when abroad — to switch the PTT service on or off when the device is used outside of the home network
Send my PTT address — Select No to hide your PTT address from channel and one-to-one calls.
Configuration settings
You may receive the settings for connecting to the service from your service provider. See "Configuration setting service," p. 7.
You can also enter the settings manually. See "Configuration," p. 28.
To select the settings for connecting to the service, select Menu > Push to talk > Config. settings.
16.
Applications
You can manage applications and games. These files are stored in the device memory or an attached memory card and may be
arranged in folders.
You can format, lock, and unlock the memory card. See "Memory card," p. 29.
Launch a game
Your device software may include some games.
Select Menu > Applications > Games. Scroll to the desired game, and select Open.
34
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
O r g a n i z e r
To set sounds, lights, and shakes for the game, select Menu > Applications > Options > App. settings. You can select more
options. See "Application options," p. 35.
Launch an application
Your device software may include some Java applications.
Select Menu > Applications > Collection. Scroll to an application, and select Open.
Application options
•
•
Update version — to verify that a new version of the application is available for download from the web (network service)
Web page — to provide further information or additional data for the application from an internet page (network service),
if available
•
App. access — to restrict the application from accessing the network
Download an application
Your device supports J2ME Java applications. Ensure that the application is compatible with your device before downloading it.
Important: Only install and use applications and other software from trusted sources, such as applications that are
TM
Symbian Signed or have passed the Java Verified testing.
You can download new Java applications and games in different ways.
•
Select Menu > Applications > Options > Downloads > App. downloads; the list of available bookmarks is shown. See
•
Use the Nokia Application Installer from PC Suite to download the applications to your device.
For the availability of different services, pricing, and tariffs, contact your service provider.
Yourdevicemayhavesomebookmarksorlinkspreinstalledforormayallowaccesstositesprovidedbythirdpartiesnotaffiliated
with Nokia. Nokia does not endorse or assume any liability for these sites. If you choose to access them, you should take the
same precautions, for security or content, as you would with any internet site.
17.
Organizer
Alarm clock
To set the device to sound an alarm at a desired time, select Menu > Organiser > Alarm clock.
Set the alarm
To set the alarm, select Alarm time, and enter the alarm time.
To change the alarm time when the alarm time is set, select On.
To set the device to alert you on selected days of the week, select Repeat alarm.
To select the alarm tone, select Alarm tone. If you select the radio as an alarm tone, connect the headset to the device.
To set a snooze time-out, select Snooze time-out and the time.
Stop the alarm
When the alarm time is reached, the device sounds an alert tone and flashes Alarm! and the current time on the display, even
if the device is switched off.
To stop the alarm, select Stop. If you let the device continue to sound the alarm for a minute or select Snooze, the alarm stops
for the time you set in Snooze time-out, then resumes.
If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone.
If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to
make and receive calls. Do not select Yes when wireless device use may cause interference or danger.
Calendar
Select Menu > Organiser > Calendar.
The current day has a frame around the number. If there are any notes set for the day, the day is in bold type. To view the day
notes, select View. To view a week, select Options > Week view. To delete all notes in the calendar, select the month or week
view, and Options > Delete all notes.
35
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
O r g a n i z e r
In Settings you can set the date, time, time zone, date or time format, date separator, default view, or the first day of the week.
In Auto-delete notes you can set the device to delete old notes automatically after a specified time.
Make a calendar note
Select Menu > Organiser > Calendar.
Scroll to the date, and select Options > Make a note and one of the following note types:
Meeting,
Call,
Birthday,
Memo, or
Reminder. Fill in the fields.
Note alarm
The device displays the note, and, if an alarm is set, sounds a tone. If a call note
is displayed, press the call key to make the
call.
To stop the alarm and to view the note, select View. To stop the alarm for 10 minutes, select Snooze. To stop the alarm without
viewing the note, select Exit.
To-do list
Save a note for a task that you must do.
Select Menu > Organiser > To-do list. To make a note if no note is added, select Add note; otherwise, select Options >
Add. Fill in the fields, and select Save.
To view a note, scroll to it, and select View. While viewing a note, you can also select an option to edit the attributes. You can
also select an option to delete the selected note and delete all the notes that you have marked as done.
Notes
To write and send notes, select Menu > Organiser > Notes.
To make a note if no note is added, select Add note; otherwise, select Options > Make a note. Write the note, and select
Save.
Calculator
The calculator in your device provides basic arithmetic and trigonometric functions, calculates the square and the square root,
the inverse of a number, and converts currency values.
Note: This calculator has limited accuracy and is designed for simple calculations.
Calculations - Select Menu > Organiser > Calculator. When 0 is displayed on the screen, enter the first number in the
calculation. Press # for a decimal point. Scroll to the desired operation or function, or select it from the Options. Enter the second
number. Repeat this sequence as many times as it is necessary.
Currency conversion - To perform a currency conversion select Options > Exchange rate. Select either of the displayed
options. Enter the exchange rate, press # for a decimal point, and select OK. The exchange rate remains in the memory until
you replace it with another one. To perform the currency conversion, enter the amount to be converted, and select Options >
In domestic or In foreign.
Note: When you change the base currency, you must enter new exchange rates because all previously set exchange
rates are cleared.
Timers
Countdown timer
1. To activate the countdown timer, select Menu > Organiser > Timer > Normal timer, enter the alarm time, and write a
note that is displayed when the time expires. To change the countdown time, select Change time.
2. To start the timer, select Start.
3. To stop the timer, select Stop timer.
Interval timer
1. To have an interval timer with up to 10 intervals started, first enter the intervals.
2. Select Menu > Organiser > Timer > Interval timer.
3. To start the timer, select Start timer > Start.
36
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
W e b
Stopwatch
You can measure time, take intermediate times, or take lap times using the stopwatch. During timing, the other functions of
the device can be used.
Using the stopwatch or allowing it to run in the background when using other features increases the demand on battery power
and reduces the battery life.
Select Menu > Organiser > Stopwatch and from the following options:
•
Split timing — to take intermediate times. To start the time observation, select Start. Select Split every time that you want
to take an intermediate time. To stop the time observation, select Stop. To save the measured time, select Save. To start the
time observation again, select Options > Start. The new time is added to the previous time. To reset the time without saving
it, select Reset.
•
•
•
•
Lap timing — to take lap times
Continue — to view the timing that you have set in the background
Show last — to view the most recently measured time if the stopwatch is not reset
View times or Delete times — to view or delete the saved times
To set the stopwatch timing in the background, press the end key.
18.
Web
Important: Use only services that you trust and that offer adequate security and protection against harmful software.
With your device browser, access various mobile internet services that use wireless markup language (WML) or extensible
hypertext markup language (XHTML) on their pages. Appearance may vary due to screen size. You may not be able to view all
details of the internet pages.
Check the availability of these services, pricing, tariffs, and instructions with your service provider.
Set up browsing
You may receive the configuration settings required for browsing as a configuration message from the service provider that
offers the service that you want to use. See "Configuration setting service," p. 7.
You can also enter all the configuration settings manually. See "Configuration," p. 28.
Connect to a service
Ensure that the correct configuration settings of the service are activated.
1. To select the settings for connecting to the service, select Menu > Web > Settings > Configuration settings.
2. Select Configuration. Only the configurations that support browsing service are shown. Select a service provider, Default,
3. Select Account and a browsing service account contained in the active configuration settings.
4. Select Display terminal window > Yes to perform manual user authentication for intranet connections.
Make a connection to the service in one of the following ways: Select Menu > Web > Home; or in the standby mode, press
and hold 0.
To select a bookmark of the service, select Menu > Web > Bookmarks.
To select the last URL, select Menu > Web > Last web address.
To enter the address of the service, select Menu > Web > Go to address. Enter the address of the service, and select OK.
Browse pages
After you make a connection to the service, you can start browsing its pages. The function of the device keys may vary in different
services. Follow the text guides on the device display. For more information, contact your service provider.
Browse with phone keys
To browse through the page, scroll in any direction.
To select an item, press the call key or Select.
To enter letters and numbers, press 0 to 9.
To enter special characters, press *.
37
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
W e b
Direct calling
While browsing, you can make a phone call and save a name and a phone number from a page.
Bookmarks
You can save page addresses as bookmarks in the device memory.
1. While browsing, select Options > Bookmarks; or in the standby mode, select Menu > Web > Bookmarks.
2. Select a bookmark, or press the call key to connect to the page.
3. Select Options to create and manage bookmarks.
Yourdevicemayhavesomebookmarksorlinkspreinstalledforormayallowaccesstositesprovidedbythirdpartiesnotaffiliated
with Nokia. Nokia does not endorse or assume any liability for these sites. If you choose to access them, you should take the
same precautions, for security or content, as you would with any internet site.
When you receive a bookmark, 1 bookmark received is displayed. To view the bookmark, select Show.
Appearance settings
While browsing, select Options > Other options > Appear. settings; or in the standby mode, select Menu > Web >
Settings > Appearance settings and from the following options:
•
•
•
•
Text wrapping — to select how the text is displayed
Font size — to set the font size
Show images — Select No to hide images on the page.
Alerts — Select Alert for unsecure connection > Yes to set the device to alert you when a secure connection changes to
an unsecure connection while browsing.
•
Alerts — Select Alert for unsecure items > Yes to set the device to alert when a secure page contains an unsecure item.
These alerts do not guarantee a secure connection. See "Browser security," p. 39.
Character encoding — Select Content encoding to set the encoding for the browser page content.
Character encoding — Select Unicode (UTF-8) web addresses > On to set the device to send a URL as UTF-8 encoding.
Screen size — to set the screen layout to Full or Small
•
•
•
•
JavaScript — to enable the Java scripts
Security settings
Cookies
A cookie is data that a site saves in the cache memory of your device. Cookies are saved until you clear the cache memory. See
While browsing, select Options > Other options > Security > Cookie settings; or in the standby mode, select Menu >
Web > Settings > Security settings > Cookies.
To allow or prevent the device from receiving cookies, select Allow or Reject.
Scripts over secure connection
You can select whether to run scripts from a secure page. The device supports WML scripts.
While browsing, to allow the scripts, select Options > Other options > Security > WMLScript sett.; or in the standby mode,
select Menu > Web > Settings > Security settings > WMLScripts over secure connection > Allow.
Download settings
ToautomaticallysavealldownloadedfilesinGallery, selectMenu > Web > Settings > Downloadingsettings > Automatic
saving > On.
Service inbox
The device is able to receive service messages sent by your service provider (network service). Service messages are notifications
(for example, news headlines) that may contain a text message or an address of a service.
Service inbox access
Select Show to access the Service inbox when you receive a service message.
If you select Exit, the message is moved to the Service inbox.
38
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
W e b
To access the Service inbox later, select Menu > Web > Service inbox. To access the Service inbox while browsing, select
Options > Other options > Service inbox. Scroll to the message you want, and select Retrieve to activate the browser and
download the complete message.
To display detailed information on the service notification or delete the message, select Options > Details or Delete.
Service inbox settings
Select Menu > Web > Settings > Service inbox settings and from the following options:
•
•
Service messages — to set whether you want to receive service messages
Message filter — Select On to set the device to receive service messages only from content authors approved by the service
provider. To view the list of the approved content authors, select Trusted channels.
•
Automatic connection — Select On to set the device to automatically activate the browser from the standby mode, when
the device has received a service message. If you select Off, the device activates the browser only after you select Retrieve
when the device has received a service message.
Cache memory
A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential
information requiring passwords, empty the cache after each use. The information or services you have accessed are stored in
the cache.
To clear the cache while browsing, select Options > Other options > Clear the cache.
In the standby mode, select Menu > Web > Clear the cache.
Browser security
Security features may be required for some services, such as online banking or shopping. For such connections you need security
certificates and possibly a security module, which may be available on your SIM card. For more information, contact your service
provider.
Security module
The security module improves security services for applications requiring a browser connection and allows you to use a digital
signature. The security module may contain certificates as well as private and public keys. The certificates are saved in the
security module by the service provider.
To view or change the security module settings, select Menu > Settings > Security > Security module settings.
Certificates
Important: Even if the use of certificates makes the risks involved in remote connections and software installation
considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a
certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted
certificates for increased security to be available. Certificates have a restricted lifetime. If "Expired certificate" or
"Certificate not valid yet" is shown even if the certificate should be valid, check that the current date and time in your
device are correct.
There are three kinds of certificates: server certificates, authority certificates, and user certificates. You may receive these
certificates from your service provider. Authority certificates and user certificates may also be saved in the security module by
your service provider.
To viewthe listofthe authority orusercertificatesdownloadedto yourphone, selectMenu > Settings > Security > Authority
certificates or User certificates.
is displayed during a connection if the data transmission between the phone and the content server is encrypted.
The security icon does not indicate that the data transmission between the gateway and the content server (or place where
the requested resource is stored) is secure. The service provider secures the data transmission between the gateway and the
content server.
Digital signature
You can create digital signatures with your phone if your SIM card has a security module. The digital signature is the same as
signing your name to a paper bill, contract, or other document.
To create a digital signature, select a link on a page (for example, the title of the book you want to buy and its price). The text
to be signed is shown and may include the amount and date.
39
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
S I M s e r v i c e s
Check that the header text is Read and that the digital signature icon
is shown. If the digital signature icon does not appear,
there is a security breach; do not enter any personal data (such as your signing PIN).
To sign the text, read all of the text first, and select Sign. The text may not fit within a single screen. Therefore, make sure to
scroll through and read all of the text before signing.
Select the user certificate you want to use, and enter the signing PIN. The digital signature icon disappears, and the service may
display a confirmation of your purchase.
19.
SIM services
Your SIM card may provide additional services. You can access this menu only if it is supported by your SIM card. The name and
contents of the menu depend on the available services.
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider or
other vendor.
To set the phone to show you the confirmation messages sent between your phone and the network when you are using the
SIM services, select Menu > Settings > Phone > Confirm SIM service actions > Yes.
Accessing these services may involve sending messages or making a phone call for which you may be charged.
20.
PC connectivity
Send and receive e-mail, and access the internet when your device is connected to a compatible PC through a Bluetooth, an
infrared, or a data cable connection. Use your device with a variety of PC connectivity and data communications applications.
Nokia PC Suite
With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do notes between your device and the compatible PC
or a remote internet server (network service). You may find more information and PC Suite on the Nokia website. See "Nokia
Packet data, HSCSD, and CSD
With your phone, you can use the packet data, high-speed circuit switched data (HSCSD), and circuit switched data (CSD, GSM
data) data services. For availability and subscription to data services, contact your service provider.
The use of HSCSD services consumes the battery faster than normal voice or data calls.
Bluetooth
Use Bluetooth technology to connect your compatible laptop to the internet. Your phone must have activated a service provider
that supports internet access, and your PC has to support Bluetooth PAN (personal area network). After connecting to the network
access point (NAP) service of the phone and pairing with your PC, your phone automatically opens a packet data connection to
the internet. PC Suite software installation is not necessary when using the NAP service of the phone. See "Bluetooth wireless
Data communication applications
For information on using a data communication application, refer to the documentation provided with it.
Making or answering phone calls during a computer connection is not recommended as it might disrupt the operation.
For better performance during data calls, place the device on a stationary surface with the keypad facing downward. Do not
move the device during a data call. For example, do not hold the device during a data call.
40
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
B a t t e r y
21.
Battery
Battery information
Your device is powered by a rechargeable battery. The battery can be charged and discharged hundreds of times, but it will
eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia
approved batteries, and recharge your battery only with Nokia approved chargers designated for this device.
If a replacement battery is being used for the first time or if the battery has not been used for a prolonged period, it may be
necessary to connect the charger, then disconnect and reconnect it to begin charging the battery.
Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to
a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.
If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or
before any calls can be made.
Use the battery only for its intended purpose. Never use any charger or battery that is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes
direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This
might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage
the battery or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and
lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery
may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures
well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according
to local regulations. Please recycle when possible. Do not dispose as household waste.
Do not dismantle or shred cells or batteries. In the event of a battery leak, do not allow the liquid to come in contact with the
skin or eyes. In the event of such a leak, flush your skin or eyes immediately with water, or seek medical help.
Nokia battery authentication guidelines
Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an
authorized Nokia dealer, look for the Nokia Original Enhancements logo on the packaging, and inspect the hologram label using
the following steps:
Successful completion of the four steps is not a total assurance of the authenticity of the battery. If you have any reason to
believe that your battery is not an authentic, original Nokia battery, you should refrain from using it, and take it to the nearest
authorized Nokia service point or dealer for assistance. Your authorized Nokia service point or dealer will inspect the battery
for authenticity. If authenticity cannot be verified, return the battery to the place of purchase.
Authenticate hologram
1. When looking at the hologram on the label, you should see the Nokia connecting hands symbol from one
angle and the Nokia Original Enhancements logo when looking from another angle.
2. When you angle the hologram left, right, down, and up, you should see 1, 2, 3, and 4 dots on each side
respectively.
3. Scratch the side of the label to reveal a 20-digit code, for example, 12345678919876543210. Turn the
battery so that the numbers are facing upwards. The 20-digit code reads starting from the number at the
top row followed by the bottom row.
41
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
B a t t e r y
4. Confirm that the 20-digit code is valid by following the instructions at www.nokia.com/batterycheck.
To create a text message, enter the 20-digit code, for example, 12345678919876543210, and send to +44
7786 200276.
National and international operator charges will apply. You should receive a message indicating whether the
code can be authenticated.
What if your battery is not authentic?
If you cannot confirm that your Nokia battery with the hologram on the label is an authentic Nokia battery, please do not use
the battery. Take it to the nearest authorized Nokia service point or dealer for assistance. The use of a battery that is not approved
by the manufacturer may be dangerous and may result in poor performance and damage to your device and its enhancements.
It may also invalidate any approval or warranty applying to the device.
To find out more about original Nokia batteries, visit www.nokia.com/battery.
42
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will
help you protect your warranty coverage.
•
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode
electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing
it.
•
•
Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.
Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp
or melt certain plastics.
•
Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device
and damage electronic circuit boards.
•
•
•
•
•
•
Do not attempt to open the device other than as instructed in this guide.
Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
Do not paint the device. Paint can clog the moving parts and prevent proper operation.
Use a soft, clean, dry cloth to clean any lenses, such as camera, proximity sensor, and light sensor lenses.
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could
damage the device and may violate regulations governing radio devices.
•
•
•
Use chargers indoors.
Always create a backup of data you want to keep, such as contacts and calendar notes.
To reset the device from time to time for optimum performance, power off the device and remove the battery.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly,
take it to the nearest authorized service facility for service.
Disposal
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union all
electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste.
Return the products to collection to prevent possible harm to the environment or human health from uncontrolled waste
disposal and to promote the sustainable reuse of material resources. Collection information is available from the product retailer,
local waste authorities, national producer responsibility organizations, or your local Nokia representative. For more information,
Additional safety information
Small children
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Operating environment
This device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at
least 2.2 centimeters (7/8 inches) away from the body. When a carry case, belt clip, or holder is used for body-worn operation,
it should not contain metal and should position the device the above-stated distance from your body.
To transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data
files or messages may be delayed until such a connection is available. Ensure the above separation distance instructions are
followed until the transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic
storage media near the device, because information stored on them may be erased.
Medical devices
Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately
protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately
shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations
43
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
A d d i t i o n a l s a f e t y i n f o r m a t i o n
posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive
to external RF energy.
Implanted medical devices
Manufacturers of medical devices recommend that a minimum separation of 15.3 centimeters (6 inches) should be maintained
between a wireless device and an implanted medical device, such as a pacemaker or implanted cardioverter defibrillator, to
avoid potential interference with the medical device. Persons who have such devices should:
•
Always keep the wireless device more than 15.3 centimeters (6 inches) from the medical device when the wireless device is
turned on.
•
•
•
•
Not carry the wireless device in a breast pocket.
Hold the wireless device to the ear opposite the medical device to minimize the potential for interference.
Turn the wireless device off immediately if there is any reason to suspect that interference is taking place.
Read and follow the directions from the manufacturer of their implanted medical device.
If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.
Hearing aids
Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel
injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more
information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added.
Only qualifiedpersonnelshouldservice the device orinstallthe device inavehicle. Faulty installationorservice may be dangerous
and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment in your vehicle
is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same
compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate
with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could
result.
Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless
teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may
be illegal.
Potentially explosive environments
Switch off your device when in any area with a potentially explosive atmosphere, and obey all signs and instructions. Potentially
explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas
could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas;
chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not
always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied
petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust, or metal
powders.
Emergency calls
Important: Wireless phones, including this device, operate using radio signals, wireless networks, landline networks,
and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never
rely solely on any wireless device for essential communications like medical emergencies.
To make an emergency call:
1. If the device is not on, switch it on. Check for adequate signal strength.
Some networks may require that a valid SIM card is properly inserted in the device.
2. Press the end key as many times as needed to clear the display and ready the device for calls.
3. Enter the official emergency number for your present location. Emergency numbers vary by location.
4. Press the call key.
If certain features are in use, you may first need to turn those features off before you can make an emergency call. Consult this
guide or your service provider for more information.
When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the
only means of communication at the scene of an accident. Do not end the call until given permission to do so.
44
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
A d d i t i o n a l s a f e t y i n f o r m a t i o n
CERTIFICATION INFORMATION (SAR)
This mobile device meets guidelines for exposure to radio waves.
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves
recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP
and include safety margins designed to assure the protection of all persons, regardless of age and health.
The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The
SAR limit stated in the ICNIRP guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests for SAR are
conducted using standard operating positions with the device transmitting at its highest certified power level in all tested
frequency bands. The actual SAR level of an operating device can be below the maximum value because the device is designed
to use only the power required to reach the network. That amount changes depending on a number of factors such as how
close you are to a network base station. The highest SAR value under the ICNIRP guidelines for use of the device at the ear is
0.82 W/kg (RM-237) and 0.96 W/kg (RM-274).
Use of device accessories and enhancements may result in different SAR values. SAR values may vary depending on national
reporting and testing requirements and the network band. Additional SAR information may be provided under product
45
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
codes
A
configuration 28
access codes
configuration setting service
connectivity 40
contact information
contacts 21
copy 22
antenna
delete 22
groups 22
B
move 22
barring password
battery 41
search 22
charging
blacklist 18
Bluetooth 25, 40
bookmarks 38
browser 37
settings 22
bookmarks 38
cache 39
synchronize 22
cookies 38
CSD 40
certificates 39
cookies 38
customer service
security 39
D
data
C
communication 40
transfer 26
calculator 36
calendar 35
note 36
dialing 12
calls
downloads 7, 38
E
answer 13
dialed 23
enhancements 27
equalizer 32
international 12
missed 23
options 13
received 23
reject 13
F
See also flight mode
camera 30
capitals 13
case
lower 13
upper 13
certificates 39
characters 13
G
gallery 29
files 29
charge the battery
clock 24
folders 29
games 34
46
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
H
N
handsfree
navigation 14
Nokia contact information
note 36
See loudspeaker
headphones
headset
notes 36
HSCSD 40
I
O
organizer 35
indicators 11
P
installation
parts 10
internet 37
J
phonebook
See contacts
K
phonelock
keys 10
See keypad lock
PictBridge 27
picture 30
keyguard 12
PIN codes
positioning 23
postcards 16
profiles 23
L
language 27
log 23
loudspeaker 13
PTT
See push to talk
M
PUK codes
settings 34
insert
menu 14
R
messages
Radio 31
recorder 32
redial 27
delete 20
S
folders 17
screen 24
scrolling 14
security
postcard 16
settings 20
browser 39
certificates 39
text 14
codes
module 39
security code
service
microSD card
insert
inbox 38
MMS
messages 38
services 37
See multimedia messages
SIM 40
47
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
I n d e x
settings 23
themes 24
timer 36
Bluetooth 25
call 27
tones 24
clock 24
configuration 28
date 24
U
display 24
downloads 38
enhancements 27
V
messages 20
phone 27
profiles 23
restoring 29
security 28
W
shortcuts 24
themes 24
wallpaper 24
web 37
time 24
tones 24
X
wallpaper 24
SIM
XHTML 37
messages 20
services 40
installation
SMS
See text message
requesting 28
stopwatch 37
strap
synchronization 26
T
text 13
48
© 2007 Nokia. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|