User's Manual
15/31 Band Graphic Equalizer
EQU Series
+18
0dB
-
+18
0dB
-
R
Version 1.0 April 2002
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Dear Customer:
Thanks for choosing LTO Graphic Equalizer and thanks for choosing one of the results of LTO AUDIO
TEAM job and researches.
For our LTO AUDIO TEAM, music and sound are more than a job...are first of all passion and let us say...our
obsession!
We have been designing professional audio products for a long time in cooperation with some of the major
brands in the world in the audio field.
The LTO line presents unparalleled analogue and digital products made by Musicians for Musicians in our
R&D Centres in Italy, Netherlands, United Kingdom and Taiwan. The core of our digital audio products is a
sophisticated DSP (Digital sound processor) and a large range of state of the art algorithms which have been
developed by our Software Team for the last 7 years.
Because we are convinced you are the most important member of LTO AUDIO TEAM and the one confirming
the quality of our job, we would like to share with you our work and our dreams, pay attention to your suggestions
and your comments.
Following this idea we create our products and we will create the new ones! From our side, we guarantee you
and we will guarantee you also in future the best quality, and the best fruits of our continuous researches
and the best prices.
Our LTO Graphic Equalizer is the result of many hours of listening and tests involving common people, area
experts, musicians and technicians.
The results of this effort is a high-end Graphic Equalizer which will provide a permanent precise equalization to
the musician, performer, studio engineer and sound contractor .
Nothing else to add, but that we would like to thank all the people that made the LTO Graphic Equalizer a
reality available to our customers, thank our designers and all LTO staff, there to make possible the realization
of products containing our idea of music and sound and there to support you, our customers, in the best way,
conscious that you are our best richness.
Thank you very much.
LTO AUDIO TEAM
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENT
1. INTRODUCTION ..........................................................................................................................4
2. FEATURE LIST ............................................................................................................................4
3. CONTROL ELEMENTS.................................................................................................................4
3.1 The Front Panel
3.2 The Rear Panel
4. INSTALLATION & CONNECTION ..................................................................................................8
4.1 Mains Connection
4.2 Audio Connection
- Wiring Configuration
- In Line Connection
- Insert Points Connection
4.3 Rack Mounting
5. APPLICATION..............................................................................................................................10
5.1 The Sound Frequency
5.2 Equalizer In Sound Reinforcement Systems
-Line Instrument
-Mixing Console
6. TECHNICAL SPECIFICATIONS ....................................................................................................12
7. WARRANTY ................................................................................................................................13
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INTRODUCTION
Thank you very much for expressing your confidence in LTO products by purchasing our EQU Series Graphic
Equalizers. With the EQU Series you have acquired an extremely musical and flexible Graphic Equalizer.
The high-end EQU Series are based on many years of experience and are designed to provide a permanent precise
equalization to the musician, performer, studio engineer and sound contractor. The EQU Series can be used
wherever is requested to modify the frequency " contour " of a sound and can offer a solution to many common
sound problems and allows the user to use the creativity to obtain nice results in terms of sound characterization.
EQU Series Graphic Equalizers include the following seven models:
EQU131 - Graphic Mono 31 Band Equalizer
EQU215 - Graphic Stereo 15 Band Equalizer
EQU2215 - Graphic Stereo 15 Band Equalizer
EQU131VU - Graphic Mono 31 Band Equalizer / VU Meter*1
EQU231VU- Graphic Stereo 31 Band Equalizer / VU Meter*2
EQU231LED - Graphic Stereo 31 Band Equalizer / LED Display*2
EQU231TWIN - Graphic Stereo 31Band Equalizer /LED Display*2
2. FEATURE LIST
Easy to Operate Front Panel Controls
Constant Q circuitry with a 3% center frequency accuracy
Control range 6dB / 12dB selectable
Active balanced and unbalanced input and output connectors
Variable input level control
Signal clip pilot
Ground "LIFT" switch to disconnect signal ground from chassis ground
Power off automatic bypass function
Line voltage selectable
Robust and Compact design
Intended for installation in standard 19" rack space
Manufactured Under ISO9001 Certified management system
3. CONTROL ELEMENTS
3.1 The Front Panel
EQU131 Front Panel
31 Band Graphic Equalizer
+12 +6
0
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
R
ON
EQU131
OFF
-12 -6
40Hz
16 KHz
CLIP
6
12
20
25
31.5
40
50
63
80
100
125 160
200
250
315
400
500
630
800
1K 1.25K 1.6K 2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
1
2
3
4
5 76 9 8 10
4 1213
EQU215 Front Panel
3
4 1213
3
Dual 15 Band Graphic Equalizer
Channel One
HI-PASS LOW-PASS
Channel Two
HI-PASS LOW-PASS
40Hz
16KHz
12
40Hz
16KHz
12
+12 +6
0
+18
0dB
-
+12 +6
0
+18
0dB
-
R
40Hz
16KHz
40Hz
16KHz
ON
EQU215
6
6
OFF
-12 -6
-12 -6
BY-PASS
CLIP
BY-PASS
CLIP
BYPASS RANGE
BYPASS RANGE
25
40
63
100
160
250 400
630
1K
1.6K 2.5K 4K
6.3K 10K 16K
LEVEL
25
40
63
100 160
250
400
630
1K 1.6K 2.5K
4K 6.3K 10K 16K
LEVEL
POWER
1
1
2
6
8
57
2
6
8
57 10
EQU2215 Front Panel
13
13
12
12
Dual 15 Band Graphic Equalizer
Channel One
Channel Two
+12 +6
+18
+14
+10
0dB
+12 +6
+18
+14
+10
0dB
3
R
0
0
HI-PASS LOW-PASS
HI-PASS LOW-PASS
EQU2215
-
8
-
8
40Hz
16KHz
12
40Hz
16KHz
12
-12
-12
-
40Hz
16KHz
40Hz
16KHz
ON
6
6
OFF
-
0
-12 -6
-12 -6
BY-PASS
CLIP
BY-PASS
CLIP
BYPASS RANGE
BYPASS RANGE
25
40
63
100
160
250 400
630
1K
1.6K 2.5K 4K
6.3K 10K 16K
LEVEL
25
40
63
100 160
250
400
630
1K 1.6K 2.5K
4K 6.3K 10K 16K
LEVEL
POWER
1
7
1
2
6
8
5
4
7
2
6
8
5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EQU131VU Front Panel
11
31 Band Graphic Equalizer
+12 +6
+17
+13
+ 9
0dB
- 9
R
LTO
POWER OUTPUT
R
0
EQU131VU
HI-PASS LOW-PASS
BY-PASS RANGE
-13
-
ON
-12 -6
OFF
40Hz
16 KHz
CLIP
6
12
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K 2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
2
3 12413 57
3
9 8 10
4 1213
1
EQU231VU Front Panel
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K
8K
10K 12.5K 16K 20K
LEVEL
HI-PASS LOW-PASS
40Hz
16KHz
12
+12 +6
+17
0dB
-
40Hz
16KHz
0
R
6
LTO
POWER OUTPUT
-12 -6
BY-PASS
CLIP
BYPASS RANGE
HI-PASS LOW-PASS
R
Channel One
Channel Two
31 Band Graphic Equalizer
EQU231VU
40Hz
16KHz
12
+12 +6
0
+17
0dB
-
40Hz
16KHz
R
ON
LTO
POWER OUTPUT
6
OFF
-12 -6
BY-PASS
CLIP
BYPASS RANGE
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K
8K
10K 12.5K 16K 20K
LEVEL
POWER
1
6
8
57 10
2
11
EQU231LED Front Panel
14
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
+12 +6
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
0
-12 -6
R
Channel One
Channel Two
40Hz
16 KHz
CLIP
6
12
Dual 31 Band Graphic Equalizer
EQU231LED
+12 +6
0
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
ON
OFF
-12 -6
40Hz
16 KHz
CLIP
6
12
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
1
2
3 12413 57
14
9 8 10
EQU231TWIN Front Panel
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K 2K
2.5K 3.15K 4K
5K
6.3K 8K
10K 12.5K 16K 20K
LEVEL
+12 +6
+17
+13
+ 9
0dB
- 9
0
HI-PASS LOW-PASS
BY-PASS RANGE
-13
-
-12 -6
40Hz
16 KHz
CLIP
6
12
R
Channel One
Channel Two
Dual 31 Band Graphic Equalizer
EQU231TWIN
+12 +6
+17
+13
+ 9
0dB
- 9
0
HI-PASS LOW-PASS
BY-PASS RANGE
-13
-
ON
OFF
40Hz
16 KHz
CLIP
6
12
-12 -6
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K 2K
2.5K 3.15K 4K
5K
6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
1
2
3 12413 57
9 8 10
1. Filter level controls
Each one of these linear potentiometers will boost or attenuate (either 6dB or 12dB) the selected
frequency at a preset bandwidth.
When all the sliders are in the centre position, the output of the equalizer is flat response.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Level control
This control sets the input signal level to the equalizer. Its "0dB" position is unity gain (no boost or attenuation).
If the clip LED(5) is light continuously, turndown this control until it only flickers occasionally.
3. High pass filter
This button electronically inserts a filter into the signal path, which cuts the low frequencies at 40Hz (12dB
per octave). The LED (12) indicator lights when the button is pressed and this filter is serving in the circuit.
4. Low pass filter
This button electronically inserts a filter into the signal path, which cuts the high frequencies at 16KHz (12dB
per octave). The LED (13) indicator lights when the button is pressed and this filter is serving in the circuit.
5. Clip LED
This LED will light when any section of the equalizer is within 5 dB of clipping. Occasional flickering of
this clip LED is acceptable, but if it remains on continuously, you should turn down the level control or
reduce the output level of the preceding component to avoid audible distortion.
6. Bypass switch
This switch inserts or removes the equalizer channel path. If bypass, the bypass LED(7) will be
illuminated to indicate it is in bypass mode. When bypassed, the input signal is routed directly to the
output jacks. When power loss, the unit automatic bypassed.
7. Bypass LED
When this LED lights, it is in bypass mode.
8. Range switch
This button switches the gain range of the filter potentiometer between 6dB and 12dB.
9. Filter range indicator
When the 6dB range is selected, green LED will light. When the 12dB range is selected, red LED will
light.
10. Power switch
This is used to switch the equalizer on and off. The appliance would be turned on when the power switch
to be set to the on-position, and it would be turned off when the switch be set to the off-position.
11. VU meter
This VU meter is used to indicate the output level.
12. High pass LED
When the High pass filter(40Hz/12dB) is in active, this LED will light.
13. Low pass LED
When the Low pass filter(16KHz/12dB) is in active, this LED will light.
14. Output level meter
This output level meter is used to indicate the output level.
3.2 The Rear Panel
EQU131 Rear Panel
19
PUSH
RISK OF FIRE-REPLACE
FUSE AS MARKED
OUT
IN
OUT
IN
Rheinland
Production inspected
MODEL
SERIAL
NEW TIDE
3
2
1
LIFT
GND
C
US
OUT
IN
UNBALANCED
BALANCED
20
18
17
16
15
EQU215 Rear Panel
19
PUSH
PUSH
RISK OF FIRE-REPLACE
FUSE AS MARKED
Channel Two
IN
OUT
Channel One
IN
OUT
OUT
OUT
NEW TIDE
3
NEW TIDE
3
C
US
2
1
2
1
Rheinland
Production inspected
LIFT
GND
OUT
IN
OUT
IN
UNBALANCED
BALANCED
UNBALANCED
BALANCED
20
18
17
16
15
17
16
15
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EQU2215 Rear Panel
19
i
n
l
R
a
V
n
d
U
T
RISK OF FIRE-REPLACE
FUSE AS MARKED
o
f
c
N
n
I
o
,
a
Rheinland
r
US
Production inspected
C
t
h
c
i
A
r
e
PUSH
PUSH
MODEL
SERIAL
Channel Two
IN
OUT
Channel One
IN
OUT
OUT
IN
OUT
IN
NEW TIDE
3
NEW TIDE
3
2
1
2
1
LIFT
GND
OUT
IN
OUT
IN
UNBALANCED
BALANCED
UNBALANCED
BALANCED
20
18
17
16
15
17
16
15
EQU131VU Rear Panel
19
RISK OF FIRE-REPLACE
FUSE AS MARKED
PUSH
Rheinland
Production inspected
OUT
IN
OUT
IN
MODEL
SERIAL
NEW TIDE
3
2
1
C
US
LIFT
GND
OUT
IN
UNBALANCED
BALANCED
20
18
17
16
15
EQU231VU/EQU231LED Rear Panel
19
PUSH
Channel One
IN
OUT
OUT
IN
NEW TIDE
3
2
1
RISK OF FIRE-REPLACE
FUSE AS MARKED
OUT
BALANCED
IN
UNBALANCED
Channel Two
IN
OUT
PUSH
Rheinland
Production inspected
MODEL
SERIAL
OUT
IN
NEW TIDE
3
2
1
LIFT
GND
C
US
OUT
BALANCED
IN
UNBALANCED
17
16
15
20
18
EQU231TWIN Rear Panel
19
PUSH
Channel One
IN
OUT
OUT
IN
NEW TIDE
3
2
1
RISK OF FIRE-REPLACE
FUSE AS MARKED
OUT
IN
UNBALANCED
Channel Two
IN
OUT
BALANCED
PUSH
MODEL
SERIAL
OUT
IN
NEW TIDE
3
2
1
LIFT
GND
OUT
IN
UNBALANCED
BALANCED
20
18
17
16
15
15. XLR input and output connector
The XLR connector are actively balanced and are used to input/output the signal.
16. 1/4" TRS phone plug input and output connector
The 1/4" TRS connector are actively balanced and are used to input/output the signal.
17. RCA input and output connector
The RCA connector are unbalanced.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE : While you can use any input connector with any output connector, only one set of these con-
nectors is to be used at one time, detail wiring and connection, please refer to 4.2 audio connection.
18. Ground lift switch
This switch is used to disconnect the signal ground from the mains and chassis earth. If it is determined
that the equalizer is the cause of hum or buzz in your system due to a ground loop, move this switch to the
"lift" position.
19. Fuse holder / Voltage selector
This is a dual voltage unit. Before you attempt to connect and operate the unit, please make sure that your
local voltage matches the voltage on the fuse-holder cover.
Caution: The fuse protecting the AC supplies circuits of this unit. The fuse can only be changed by
a qualified technician, in the event of a fault or changing the supply voltage. If the fuse continues to
blow after replacing, discontinue use of this unit before repaired.
1 1 0 - 1 2 0 V
2 2 0 - 2 4 0 V
220-240V
110-120V
THIS IS SET FOR
110V AC TO 120V
AC OPERATION
THIS IS SET FOR
220V AC TO 240V
AC OPERATION
The fuse-holder above the AC connector on the rear of the chassis has 3 triangular markers(please
refer to the above pictures), with two of these triangles opposing each other, your unit is set to the
operating voltage printed next to these markers.
To change, pull fuse-holder out and rotate 180 ,then push in again.
20. AC Inlet
This connector is meant for the connection of the supplied main cord.
Do not insert power cable into unit until voltage has been correctly set. Do not plug power cable into AC
power until voltage has been correctly set.
4. INSTALLATION & CONNECTION
4.1 Mains Connection
Please ensure that the EQU Series Graphic Equalizer is set to the correct supply voltage before plugging
the power cord into the wall outlet , use the same fuse as marked on the fuse holder at the AC power
connection socket.
The mains connection of the EQU Series Graphic Equalizer is made by using the enclosed mains cable and
a standard IEC receptacle. It meets all of the international safety certification requirements.
4.2 Audio Connection
The EQU Series Graphic Equalizer presents with balanced XLR & 1/4" TRS and unbalanced RCA connectors,
and it can be interfaced by several ways to support a variety of applications without any signal loss. The
EQU Series Graphic Equalizer can be used on a single instrument by connecting to a mixing console's main
inserts, or on an entire mix "in-line" between a mixing console's outputs and a power amplifier.
- Wiring Configuration
Either the 1/4" TRS phone jack or the XLR connector can be wired in balanced and unbalanced modes, which
will be determined by the actual application status, please wire your system as the following wiring examples:
1/4"TRS jack
Unbalanced Input
1/4"TRS jack
Balanced Input
XLR Unbalanced Input
XLR Balanced Input
8
Download from Www.Somanuals.com. All Manuals Search And Download.
- In Line Connection
For these applications the EQU Series Graphic Equalizer provides 1/4" TRS connectors, XLR connectors
and RCA connectors to easily interface with most any professional audio device. Follow the configuration
examples below for your particular connection.
Balanced
Tip
Ring
Tip
Ring
Sleeve
Sleeve
TIP RING SLEEVE
SLEEVE RING TIP
1
2
1
2
3
3
Tip
Ring
1
2
3
Sleeve
TIP RING SLEEVE
Unbalanced
Tip
Ring
1
2
3
Sleeve
TIP RING SLEEVE
Tip
1
2
3
Sleeve
TIP SLEEVE
1
2
3
Centre
Screen
Tip
Tip
Sleeve
Sleeve
TIP SLEEVE
SLEEVE TIP
Tip
Ring
Tip
Ring
Sleeve
Sleeve
SLEEVE RING TIP
TIP RING SLEEVE
Tip
Centre
Screen
Sleeve
TIP SLEEVE
Tip
Ring
Centre
Sleeve
Screen
TIP RING SLEEVE
1
2
1
2
3
3
- Insert Points Connection
If you are connecting to a mixing console's main inserts, you may have a single TRS jack for SEND &
RETURN, in this case, use an insert "Y" cable that configured like the examples below.
1/4" TRS insert
Insert Leads
Tip (Send)
Sleeve
Tip
Ring
SLEEVE TIP
Tip (Return)
Sleeve
Sleeve
TIP RING SLEEVE
SLEEVE TIP
1
2(Send)
3
Tip
Ring
1
TIP RING SLEEVE
2(Return)
3
Sleeve
Centre(Send)
Screen
Tip
Ring
Centre(Return)
Screen
Sleeve
TIP RING SLEEVE
4.3. Rack Mounting
The most secure mounting is on a universal rack shelf available from various rack manufactures or your
music dealer. The EQU Series fits into one standard 19" rack unit of space, but the EQU131 and EQU215
will be 1H height, the EQU231TWIN will be 4H height, while the other four models: EQU2215, EQU131VU,
EQU231VU and EQU231LED will be 2H height. Please allow at least an additional 4" depth for the connectors
on the rear panel. Be sure that there is enough air space around the unit for sufficient ventilation and please
do not place the EQU Series on high temperature devices such as power amplifiers etc. to avoid overheating.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. APPLICATION
5.1 The Sound Frequency
In recording studios as well as stage or radio plays, the EQU Series Graphic Equalizer will be your
valuable sound tool to modify the frequency "contour " of a sound .but first of all , you should clearify the
typical frequency of each instrument and voice, so that can you obtain nice results in terms of sound
characterization. The tables on the following pages give you an idea of specific frequencies and their
acoustic significance.
Typical Frequency of Each Instrument and Voice
Mid C
CDEFGABCDEFGABCDEFGABCDEFGABCDEFGABCDEFGABCDEFGABCDEFGABCDEFGABC
25 31 40 50 62 80 100 125 160 200 250 320 400 500 640 800 1K 1.3K1.6K 2K 2.5K 3.1K 4K 5K 6.2K 8K 10K 13K 16K 20K
Hyman gearing
range VOCAL
Soprano
Contralto
Baritone
Bass
WOODWIND
Piccolo
Flute
Oboe
Clarinet in B flat or A
Clarinet in E flat
Bass Clarinet
Basset Hom
Cor Anglais
Bassoon
Double Bassoon
BRASS
Soprano Saxophone
Alto Saxophone
Tenor Saxophone
Baritone Saxophone
Bass Saxophone
Trumpet in C
Trumpet in F
Alto Trombone
Tenor Trombone
Bass Trombone
Tuba
Valve Hom
STRINGS
Violin
Viola
Cello
Double Bass
Guitar
KEYBOARDS
Pianoforte
Organ
PERCUSSION
Celesta
Timpani
Xylophone
FREQUENCY
25 31 40 50 62 80 100 125 160 200 250 320 400 500 640 800 1K 1.3K1.6K 2K 2.5K 3.1K 4K 5K 6.2K 8K 10K 13K 16K 20K
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Equalizer In Sound Reinforcement Systems
The EQU Series Graphic Equalizers can be used in the sound reinforcement systems to :
Eliminate unwanted sounds, such as the 60Hz Hum noise.
Shape the sound by changing the frequency response of the track.
Special effects like telephone sounds are done by cutting off the low end to 200Hz and the high end
to 6KHz.
Allow you to modify the sound of the instrument if put EQU Series Equalizer in line with a musical
instrument. you can brighten the sound, and body to a thin sounding instrument, or you can give the
sound a totally different character.
Fix a track that does not sound quite right, put the EQU Series Equalizer in an effects send and return
it to the mix bus.
The following connection is probably most common field of application:
- Line Instrument
The EQU Series Graphic Equalizer can be used on an entire mix "In-line" between a instrument outputs
and a power amplifier, and this is the basic application in the PA system to offer precise Equalization
control.
CH1 IN
CH2 IN
CH1 OUT
CH2 OUT
From line instrument
outputs
To power amplifier inputs
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
+12 +6
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
0
-12
-
6
R
Channel One
Channel Two
40Hz
16 KHz
CLIP
6
12
Dual 31 Band Graphic Equalizer
EQU231LED
+12 +6
0
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
ON
OFF
-12
-
6
40Hz
16 KHz
CLIP
6
12
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
- Mixing Console
The EQU Series Graphic Equalizer can also be used on a single instrument by connecting to a mixing
console's main inserts, esp for those consoles without built-in equalization circuitry.
Main Inserts
CH1 IN
CH1 OUT
CH2 IN
CH2 OUT
LEVEL
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
MIXING CONSOLE
+12 +6
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
0
-12
-
6
R
Channel One
Channel Two
40Hz
16 KHz
CLIP
6
12
Dual 31 Band Graphic Equalizer
EQU231LED
+12 +6
0
+17
0dB
-
HI-PASS LOW-PASS
BY-PASS RANGE
ON
-12
-
6
OFF
40Hz
16 KHz
CLIP
6
12
20
25
31.5
40
50
63
80
100
125
160
200
250
315
400
500
630
800
1K 1.25K 1.6K
2K 2.5K 3.15K 4K
5K 6.3K 8K
10K 12.5K 16K 20K
LEVEL
POWER
NOTE: Mono/Stereo Application
a. For mono application, please use the EQU131, EQU131VU mono Graphic Equalizer.
b. For stereo application, please use the EQU215, EQU2215, EQU231LED, EQU231VU or
EQU231TWIN stereo Graphic Equalizer, either of the two channels can be used as L/R input
& output.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6. TECHNICAL SPECIFICATIONS
Type
1
2
2
1
2
2
31 Band: 1/3 octave , ISO spacing (1H series)
15 Band: 2/3 octave , ISO spacing (1H series)
15 Band: 2/3 octave , ISO spacing (2H series)
31 Band: 1/3 octave , ISO spacing (2H series)
31 Band: 1/3 octave , ISO spacing (2H series)
31 Band: 1/3 octave , ISO spacing (4H series)
EQU131
EQU215
EQU2215
EQU131VU
EQU231VU / 231LED
EQU231TWIN
Slider travel
20mm with positive centre detente
(EQU131/EQU215/EQU231VU/EQU231LED)
60mm with positive centre detente
(EQU131VU/EQU2215/EQU231TWIN)
Range
6dB or 12dB selectable
Input connections
Active balanced XLR and 1/4" TRS
Unbalanced RCA
Input impedance
20k (bal.)
15k (unbal.)
Maximum input level
Output connections
18dBv
Active balanced XLR and 1/4" TRS
Unbalanced RCA
Output impedance
Maximum output level
Load impedance
High pass filter
600
16dBv
>10K
40Hz (12dB/oct) fixed-button type .
16KHz (12dB/oct) fixed-button type
Low pass filter
Frequency response
20Hz to 50KHz at - 3dB
0.02% (@ 1KHz , all VR at middle position)
93dB (@ 1KHz )
THD + N %
S / N ratio
Power supply
110V-120VAC -60Hz
220V-240VAC -50Hz
Consumption
1
2
2
31 band, 1/3 octave, ISO spacing: 7W
15 band, 2/3 octave, ISO spacing: 9W
31 band, 1/3 octave, ISO spacing: 12.5W
EQU131/131VU
EQU215/2215
EQU231VU / 231LED/231TWIN
483(W) 220(D) 44(H)(19" 8.66" 1.7")mm (1H series)
483(W) 220(D) 88(H)(19" 8.66" 3.5") mm (2H series)
483(W) 220(D) 177.8(H)(19" 8.66" 7") mm (4H series)
Dimensions
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7. WARRANTY
1. WARRANTY REGISTRATION CARD
To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration
Card within 10 days of the Purchase Date.
All the information presented in this Warranty Registration Card gives the manufacturer a better under-
standing of the sales status, so as to purport a more effective and efficient after-sales warranty service.
Please fill out all the information carefully and genuinely, miswriting or absence of this card will void your
warranty service.
2. RETURN NOTICE
2.1 In case of return for any warranty service, please make sure that the product is well packed in its original
shipping carton, and it can protect your unit from any other extra damage.
2.2 Please provide a copy of your sales receipt or other proof of purchase with the returned machine ,and
give detail information about your return address and contact telephone number .
2.3 A brief description of the defect will be appreciated.
2.4 Please prepay all the costs involved in the return shipping, handling and insurance.
3. TERMS AND CONDITIONS
3.1 LTO warrants that this product will be free from any defects in materials and/or workmanship for
a period of 1 year from the purchase date if you have completed the Warranty Registration Card in
time.
3.2 The warranty service is only available to the original consumer, who purchased this product directly
from the retail dealer, and it can not be transferred.
3.3 During the warranty service, LTO may repair or replace this product at its own option at no charge to
you for parts or for labor in accordance with the right side of this limited warranty.
3.4 This warranty does not apply to the damages to this product that occurred as the following conditions:
Instead of operating in accordance with the user's manual thoroughly, any abuse or misuse of this
product.
Normal tear and wear.
The product has been altered or modified in any way.
Damage which may have been caused either directly or indirectly by another product / force / etc
Abnormal service or repairing by anyone other than the qualified personnel or technician.
And in such cases, all the expenses will be charged to the buyer.
3.5 In no event shall LTO be liable for any incidental or consequential damages. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation
may not apply to you.
3.6 This warranty gives you the specific rights, and these rights are compatible with the state laws, you
may also have other statutory rights that may vary from state to state.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|