Netopia Network Router 3346EU User Manual

BROADBAND WITHOUT BOUNDARIES™  
When all of your connections are made, the status LEDs on the front of your Netopia Router  
will light, according to the following diagram:  
Set up your Router  
®
Netopia 4-Port ADSL Router  
Power - Green when power is applied  
1.After unpacking your Netopia Router shipping carton, decide where you want  
to locate the Router.  
DSL SYNC -  
Models:  
Netopia® 3346(EU, DE)-ENT / 3356(EU, DE)-ENT ADSL Routers – All Models  
Flashes green when training  
Solid green when trained  
Flashes green for DSL traffic  
You should install the Router near your PC or another location that permits easy access  
and visibility. You can lay the Netopia Router flat or mount it on a wall. Make sure any  
Ethernet cables are kept away from power cords, fluorescent lighting fixtures, and  
other sources of electrical interference. Put the Router in a location where air can circu-  
late freely around it.  
Quickstart Guide  
LAN 1, 2, 3, 4 -  
Solid green when connected  
to each port on the LAN.  
Front View  
Checklist  
Flash green when there is  
activity on each port.  
2.Connect the power transformer to the power jack on the Router back panel.  
Plug the power transformer into an appropriate electrical outlet.  
Unpack your Gateway, check your package contents, and decide on a location:  
Place the Gateway in a spot that is easily accessible for you.You can lay it flat or  
mount on the wall.  
Keep the cables away from other electrical devices that may interfere with the oper-  
ation of your Gateway.  
Turn on the power with the power switch. The Power light should come on solid green.  
ConfigureYour PC for Dynamic Addressing  
3.Connect the Router to the wall jack that supports your DSL service.  
The following instructions assume that you want to use the automatic configuration and  
address sharing features of the Router to provide IP information to devices on your local  
Ethernet network.  
Insert one end of the lavender telephone cable in the DSL port on the Router back  
panel until you feel it lock. Insert the other end of the telephone cable into the tele-  
phone jack connected to your ADSL service. The DSL SYNC indicator light should  
blink for up to two minutes and then come on solid green.  
1.Configure your computer to use an IP address on the same TCP/IP network as  
the Netopia Router.  
• Windows 95/98 or Windows ME:  
Network Neighborhood  
from the pull-down menu.  
• Right-Click on the  
Properties  
icon on your Windows desktop and  
10/100BT LAN  
DSL  
Power Supply  
select  
Rear View  
• In the list of network components, highlight the entry that says  
CD & Quickstart  
Guide  
Netopia Router  
2
TCP/IP ([your Ethernet card here])  
”.  
4
3
LAN  
2
1
Power  
Off / On  
DSL  
Properties  
• Click the  
button.  
Obtain an IP address automatically  
• Click the  
radio button. Click the DNS Con-  
radio button. Click the Gateway tab and remove  
button twice. When prompted, restart your PC.  
Power Switch  
Disable DNS  
figuration tab. Click the  
-or-  
Power Supply  
OK  
any installed Gateways. Click the  
4
International  
North American  
• Proceed to the next section “Configure Your Netopia Router”.  
3
• Windows 2000 and XP  
My Network Places  
• Right-Click on the  
Properties  
icon on your Windows desktop and select  
.
Local Area Connection  
• Select your  
.
4.Connect the Router to create your Ethernet local area network (LAN.)  
Lavender RJ-11  
Telephone Cable  
Yellow RJ-45  
Ethernet Cable  
Local Area Connection  
Properties  
• Right click on your  
and select  
.
Connect the yellow Ethernet cable to your first PC and to the Router.  
Internet Protocol [TCP/IP]  
• Select  
.
The LAN indicator light should come on solid green for the port where you connected  
your Ethernet cable.  
Properties  
• Click the  
• Click the  
button.  
If you don’t have everything, contact your supplier immediately.  
Obtain IP address automatically  
Obtain DNS  
radio button and the  
server address automatically  
OK  
button.  
radio button. Click the  
Connect each computer or other device to a switch port on the back of the Router with  
an Ethernet cable (maximum length 100 meters). If you need more than four ports, con-  
nect a hub or switch to the Router using a standard Ethernet cable.  
• Proceed to the next section “Configure Your Netopia Router”.  
1
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.  

Milwaukee Power Hammer 5366 1 User Manual
Niles Audio Stereo Receiver ZR 8630AVZR 8630AV User Manual
NordicTrack Home Gym NTL069073 User Manual
Northern Industrial Tools Impact Driver 150611 User Manual
Omega Thermometer FOB100 User Manual
Palsonic CRT Television 5160G User Manual
Panasonic Blood Pressure Monitor EW3109 User Manual
Panasonic Camcorder AG DVC60 E User Manual
Panasonic Camera Flash DMC TZ25 User Manual
Panasonic Cordless Telephone KX TG2711 User Manual