Duro Corporation
Gas Range Manual for Installation, Care & Maintenance
BX3031 BX3062 DRGB4801
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Definitions
This is a safety alert symbol. It will alert you to potential personal or property safety
hazards. Obey all safety messages to avoid any property damage, personal injury or death.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in
serious injury or death.
CAUTION indicates a moderate hazardous situation which, if not avoided, could result in
minor or moderate injury.
CAUTION
CAUTION – when used without the safety alert symbol, indicates a potentially hazardous
situation which, if not avoided, could result in property damage.
IMPORTANT
IMPORTANT used for installation, operation and maintenance information that are not
related to safety.
If the information in this manual is not followed exactly, a fire or an explosion may result causing
property damage, personal injury or even death.
Do not store or use gasoline, liquid propane cylinder or other flammable vapors and liquids in
the vicinity of this appliance.
Save this manual for future references.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
What to do if you smell gas?
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your residence.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the fire department.
IMPORTANT
The installation and service of your range product must be performed by a licensed installer, an
approved service agency or your gas supplier.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Do not store or use gasoline, liquid propane cylinder or other flammable vapors and liquids in
the vicinity of this appliance.
The installation and service of your range must be performed by a qualified installer, an
approved service agency or the gas supplier.
Gas appliances can cause minor exposure to four of these substances, namely benzene,
carbon monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of
natural gas fuel. When operating your range on natural gas, the flames from the burners
should be blue in color. In addition, the flames should be stable, free of yellow tipping,
excessive noise and lifting. However, this yellow tipping should be restricted to the primary
flame kernels only. Properly adjusted burners, indicated by a bluish rather than a yellow flame,
will minimize incomplete combustion. Exposure to those substances can be minimized by
venting with an open window or use of a ventilation fan or hood.
ELECTRICAL GROUNDING INSTRUCTIONS
IMPORTANT
This indoor cooking appliance is equipped with a three-prong (grounding) plug for your
protection against shock hazard and should be plugged directly into a properly grounded
three-pronged receptacle. DO NOT cut or remove the grounding prong from this plug.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
To ensure proper and safe operation, read all instructions before using the product. Install or
locate the product only in accordance with the provided Installation Instructions.
Do not attempt to adjust, repair, service or replace any part of your appliance unless it is
specifically recommended in this guide.
Do not use the range for warming or heating the room.
Do not leave children along or unattended in the area where the range is in use. Never allow
to sit or stand on any part of the range. Do not let children play with the range.
All servicing should be referred to a qualified technician.
Have the technician show you the location of the gas shut off valve and how to shut it off in
an emergency situation.
Always disconnect power to appliance before any type of servicing.
Do not use abrasive or caustic cleaners or detergents on this appliance. They may cause
permanent damage to the surface.
When cooking, set the burner controls so that the flame heats only the bottom of the utensil
and does not overlap at the sides of the utensil.
Utensils (pots and pans) that conduct heat slowly, i.e. glass pots, should be used in
conjunction with burner flames at a low or medium setting.
Turn off all controls and wait for appliance parts to cool down before touching them. Do not
touch the burner grates or surrounding areas until cool.
Do not use water on grease fires.
Clean appliance with caution.
Always turn pot handles to the side or back of the range. Do not turn handles towards the
area where they are easily burned. Handles should not extend over the adjacent burners.
Use the range only for cooking tasks as outlined in this manual. When using the range, do
not touch the grates, burner caps, burner bases, or any other parts in proximity to the flame.
These components may be hot enough to cause burns.
Use dry pot holders. Moist or damp pot holders on hot surfaces may result in burns from
steam.
Do not let pot holder touch hot surface areas.
Do not use a towel or other bulky cloth.
Do not heat unopened food containers. Build up of pressure may cause the container to
explode and result in injury.
During and after use, do not touch interior surfaces of the oven until cool.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Gas Supply Requirements
Installation of this range must conform with local codes, or in the absence of local codes,
than national Fuel Gas Code, ANSIZ223.1 / NFPA 54. In Canada, installation must
conform to the current natural Gas Installation /code, CAN 1-1.1-M81 and with local
codes where applicable. This range has been design-certified according to ANSIZ21.1a,
latest edition.
MINIMUM GAS SUPPLY PRESSURE TO APPLIANCE FOR LP GAS---13.0 IN.W.C.
MINIMUM GAS SUPPLY PRESSURE TO APPLIANCE FOR NG ---10.0 IN.W.C.
APPLIANCE REGULATOR IS SET AT 5.0 IN. W.C. OUTLET PRESSURE.
Keep appliance area clear and free from combustible materials, gasoline, and other
flammable vapors.
Do not obstruct the flow of combustion air into the range and ventilation air away from
the range.
Ventilation: it is recommended that the unit be set under a powered, vented exhaust
hood of sufficient size and capacity.
Before installing the range, you must locate and secure the included anti-tip bracket to
the wall for your range.
The use of cabinets for storage above the appliance may result in a potential burn
hazard. Combustible items may ignite; metallic items may become hot and cause
burns. If a cabinet storage is to be provided, the risk can be reduced by installing a
range hood that projects horizontally a minimum of 5" (12.7cm) beyond the bottom of the
cabinets.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Dimensions and Clearances
The range may be installed flush to the rear wall. You may install a non-combustible
material on the rear wall above the range and up the vent hood. It is not necessary to
install non-combustible materials behind the range below the counter top height.
The minimum distance from the side of the range above the counter top to combustible
sidewalls must be at least 10 inches.
INSTALLATION INSTRUCTIONS
30"
27 3/4"
Height
39 9/16"
41 1/16"
36"
depth with door open
44 1/4"
8
Download from Www.Somanuals.com. All Manuals Search And Download.
36"
27 3/4"
Height
39 9/16"
41 1/16"
36"
depth with door open
44 1/4"
48"
27 3/4"
Height
39 9/16"
41 1/16"
36"
depth with door open
44 1/4"
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Clearances
INSTALLATION INSTRUCTIONS
The maximum depth of cabinets installed above cooking tops be 13 in (330mm) or a great
specified by the manufactures as tested by the certification agency.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
O
FF
OFF
OFF
OFF
O
FF
O
FF
OFF
OFF
OFF
OVEN
Griddl
e
Oven
H
I
HI
HI
HI
HI
H
I
S
IM
S
IM
SIM
SIM
S
IM
SIM
LO
LO
LO
LO
LO
LO
Light
Light Convection
Fan
Electric Power Supply Requirements
Your range must be electrically grounded in accordance with local codes or, in the
absence of local codes, in accordance with the National Electrical Code (ANSI/NFPA 70,
latest edition). In Canada, electrical grounding must be in accordance with the current
CSA C22.1 Canadian Electrical Code Part 1 and/or local codes. A copy of this standard
may be obtained from: National Fire Protection Association, 1 Battery march Park,
Quincy, Massachusetts 02269-9101.
The power supply must be the correct polarity. Reverse polarity will result in continuous
sparking of the electrodes, even after flame ignition. If there is any doubt as to whether
the power supply has the correct polarity or grounded, have it checked by a qualified
electrician.
Use 120V, 60Hz, and properly grounded branch circuit protected by a 15-amp or 20-amp
circuit breaker or time delay fuse.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Grounding
1. The power cord is equipped with a three-prong (grounding) plug which mates with a
standard three-prong grounding wall receptacle to minimize the possibility of
electrical shock hazard from the range.
2. All cord connected appliance shall include instructions relative to location of the wall
receptacle and a warning to the user to disconnect the electrical supply before
serving the appliance.
3. Where a standard two-prong wall receptacle is encountered, it is the responsibility
and obligation of the customer to have it replaced with a properly grounded
three-prong wall receptacle. Do not cut or remove the grounding prong from the
power cord.
Connect Range to Gas Supply
1. Install a manual gas line shut-off valve in the gas line in an easily accessed location
outside the range in the gas piping external to the appliance for the purpose of turning
on or shutting off gas to the appliance.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Install a manual valve in an accessible location in the gas line external to the
appliance tor the purpose of turning on or shutting off gas to the appliance.
3. Install male ½” flare union adapter to ½” NPT internal thread elbow at inlet of
regulator. On models equipped with standard twin burners, install the male pipe
thread end of the ½”flare union adapter to the ½” NPT internal thread at inlet of
pressure regulator. Use a wrench on the regulator fitting to avoid damage.
4. Install male ½” or ¾” flare union adapter to the NPT internal thread of the manual
shut-off valve, taking care to secure the shut-off valve to keep it from turning.
5. The gas supply pressure for checking the regulator setting is 6in (Nature Gas) and
11inch（LP gas）connect flexible gas line connector to the regulator on the range.
Position range to permit connection at the shut-off valve.
6. When all connections have been made, make sure all range controls are in the “off”
position and turn on main gas supply valve.
7. Leak testing of the appliance shall be conducted according to the manufacture’s
instructions .Use some soap water (50% water and 50% soap) or a leak detector at
all joints and connections to check for leaks in the system. Do not use a flame to
check for gas leaks.
The appliance must be isolated from the building’s gas supply piping system by closing
its individual manual shut-off valve during any pressure testing of the gas supply piping
system at test pressure equal to or less than ½ psig (3.5kPa).
Hood/Composite Overlay Install
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The bottom of the hood should be 30” min. to 36” above the counter top. This would typically
result in the bottom of the hood being 66” to 72” above the floor. These dimensions provide
safe and efficient operation of the hood.
After Installation:
Check ignition of cooktop burners.
Check ignition of oven burner.
Visually check tubular burner (oven burner) re-ignition to be sure both rows of burner ports are
relighting each time.
Check for gas leaks at all gas connections (using a gas detector, never a flame).
Check oven bake and convection bake function.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKTOP OPERATION
Surface Burner Ignition
Ignite
Adjust to appropriate flame
height.
Push to release gas.
Turn to ‘Ignite’ position.
To light the surface burners, push and turn the appropriate control knob counter clockwise to
the “HI” position. You will hear a clicking noise – the sound of the electric spark igniting the
burner. Once burner ignition has been achieved, turn the burner control knob to adjust the the
desired heat setting.
NOTE: When one burner is turned to the “HI” position, all the burner igniters will spark. Do
not attempt to disassemble or clean around any burner while another burner is on. Do not
touch any burner cap, burner base, or igniter while the igniters are sparking.
Heat Settings:
Hi
Ignites the burners.
Simmer
Melting small quantities, steaming rice, warming food, melting chocolate
or butter.
Low
Melting large quantities.
Low-Medium
Low-temperature frying, simmering large quantities, heating milk, cream
sauces, gravies.
Medium
Sautéing and browning, braising, pan-frying, maintaining slow boil on
large quantities.
Medium – Hi
High-temperature frying, pan boiling, maintaining slow boil on large
quantities.
Boiling liquid quickly, deep frying.
Hi
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKTOP OPERATION
Oven Vent
Do not block the ducts on the rear of the range when cooking in the oven. It is important
that the flow of hot air from the oven and fresh air into the oven burner never be
interrupted. Avoid touching the vent opening or nearby surfaces during oven or broiler
operation – they may become hot.
Burner Grates
The grates must be properly positioned before cooking. Improper installation of the
grates may result in scratching of the cooktop and / or poor combustion.
Do not operate the burners without a pan or utensil on the grates.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN OPERATION
Oven Function
Natural Airflow Bake occurs when heat is transferred into the oven from the bake
burners in the bottom of the oven cavity. Heat is then circulated by natural airflow.
This is a traditional bake setting.
Infrared Broil
The broil burner is located at the top of the oven. This burner heats the metal screen
until it glows. The glowing screen produces the infrared heat, searing the outside of
broiled foods and sealing in juices.
Convection Bake
Heat is transferred from the bake burners in the bottom of the oven cavity to the oven
cavity itself. The convection fan in the rear of the oven then circulates it. This convection
process provides more even heat distribution throughout the oven cavity. Multiple rack
use is possible for the largest baking job. Convection cooking is faster, can be
accomplished at lower temperatures and provides more even temperatures than with
regular cooking.
Without oven bottom cover replace oven bottom cover before using oven
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Convection Roast
The convection fan circulates the heated air evenly over and around the food. Using the
cover and broiler pan provided, heated air will be circulated over the around the food
being roasted. The heated air seals in juices quickly for a moist and tender product
while, at the same time, creating a rich golden brown exterior. When convection
roasting, it is important that you use the broiler pan for best convection roasting results.
The pan is used to catch grease spills and has a cover to prevent grease splatters.
Convection Defrost
With temperature control off, a motorized fan in the rear of the oven circulates air. The
fan accelerates natural defrosting of the food without heat. To avoid illness and food
waste, do not allow defrost food to remain in the oven for more than two hours without
being cooked.
Convection Dehydrate
With the temperature control on 175oF, warm air is radiated from the bake burners in the
bottom of the oven cavity and is circulated by a motorized fan in the rear of the oven.
Over a period of time, the water is removed from the food by evaporation. Removal of
water inhibits growth of microorganisms and retards the activity of enzymes.
BROILER OPERATION
Note: Door must be closed during broiler operation.
Broiling is a method of cooking tender cuts of meat directly under the infrared broiler in
the oven. Broiling in the oven is accomplished with the oven door closed. It is normal and
necessary for some smoke to be present to give the food a broiled flavor.
Preheating
Preheating is suggested when searing rare steaks (Remove the broiler pan before
preheating with the infrared broiler. Foods will stick on hard metal). To preheat, turn the
“Oven” selector knob to the “Broil” position. Wait for the burner to become hot,
approximately 2 minutes. Preheating is not necessary when broiling meat well-done.
To Broil
Broil one side until the food is browned; turn and cook on the second side. Season and
serve. Always pull the rack out to the “stop” position before turning or removing food.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Broil
The “Oven” selector knob controls the Broil feature. When broiling, heat radiates
downward from the oven broiler for even coverage. The Broil feature temperature is
500ºF (260ºC).
The broil pan and insert used together allow dripping grease to drain and be kept away
from the high heat of the oven broiler. DO NOT use the broil pan without the insert.
DO NOT cover the broil pan insert with foil. The exposed grease could catch fire.
To set the oven to Broil:
1. Place the broiler pan insert on the broiler pan. Then place the food on the broiler
pan insert.
2. Arrange the interior oven rack and place the broiler pan on the rack. Be sure to
center the broiler pan and position directly under the broil burner. If preheating the
broil burner first, position the broiler pan after the broil burner is preheated.
3. Turn selector knob to Broil.
The oven indicator light will remain on until the selector knob is turned to the off position
or the temperature control cycles off.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GRIDDLE OPERATION
Before Using the Griddle
1. Clean the griddle thoroughly with warm, soapy water to remove dust or any protective
coating.
2. Rinse with clean water and wipe off to dry with soft, clean, lint-free cloth.
3. A stainless steel cover that is sized to fit on top of the surface when the griddle is not
being used is provided. Please note that the cover must be removed before turning the
griddle on.
4. Make sure the grease tray is under the front edge of the griddle. Position the tray under
the griddle overhang to catch grease or food residue.
Use of the Griddle
1. Push and turn the control knob counter-clockwise to the preferred cooking temperature.
2. Preheat the griddle for 10 – 12 minutes.
3. When the griddle is preheated to the desired temperature, the indicator light will turn on.
4. Butter or cooking oil can be added for more flavor, then plate the food to cook.
CAUTION:
The surface of the griddle is hot after use. Please allow sufficient time for the
griddle to cool prior to cleaning.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
Cooktop
To avoid electrical shock or burns, turn off controls and ensure the cooktop is cool before
cleaning.
Before cleaning the cooktop, ensure that all burners are turned off and that all
components are cool enough to safely touch.
Do not use harsh or abrasive cleaning agents, waxes, polishes, or commercial cooktop
cleaners to clean the cooktop.
Use only a sponge, soft cloth, fibrous or plastic brush, and nylon pad for cleaning.
Always dry components completely before using the cooktop.
Control Panel, Door Handle, Control Housing
Clean the control panel, door handle and control housing with a solution of mild
detergent and warm water.
Do not use abrasive cleaners or scrubbers; they may permanently damage the finish.
Dry the components with a soft, lint-free cloth.
Oven Window
Clean all glass surfaces with a solution of mild detergent and hot water. Use a mild
glass cleaner to remove fingerprint or smears.
Dry completely with a soft, lint-free cloth
Porcelain Surfaces
Clean oven interior and inner door liners with a solution of mild detergents and hot water.
Rinse and dry with a soft, lint-free cloth. Do not use abrasives or commercial oven
cleaners.
Stainless Steel Surfaces
Do not use any cleaning product with chlorine bleach.
Do not use a steel wool pad; it will scratch the surface.
Use a hot, damp cloth with a mild detergent. Use a clean, hot, dmp cloth to remove
soap. Dry with a dry, clean cloth.
Electrical Grounding Instructions:
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors
can cause improper and dangerous operation.Verify proper operation after servicing.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
Metal Finishes
Wash with soap and water, glass cleaner, or mild liquid spray.
Plastic Finishes
When control panel trim and end caps are cool, clean with soap and water, rinse and dry.
Use a glass cleaner and soft cloth.
Oven Racks
Clean oven racks with solution of detergent and hot water. To clean heavy soil, use a
scouring pad such as steel wool, with plenty of water.
Oven Frame
Clean with hot water, soap-filled steel wool pads or cleaners. Rinse well with clean water
and dry.
Oven Gasket
Do not clean the gasket. The fiberglass material of the oven door gasket cannot
withstand abrasion.
It is necessary for the gasket to remain intact.
Replacing the Oven Light
Turn off the power at the main power supply.
Remove the lens cover from the housing by pulling straight out.
To prevent electrical shock or personal injury, make sure the oven and light bulb are cool
and power to the oven has been turned off before replacing the light bulb. Make sure
the lens cover is in place when using the oven.
Outer Oven Door
Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse
well. You may also use a glass cleaner to clean the glass on the outside door.
Do not use oven cleaners, cleansing powder or harsh abrasives on the outside of the
door.
Inner Oven Door
Do not allow excess water to run into holes or slots in the door. Any soap left on the
liner causes additional stains when the oven is heated.
Before you call for service, please review the potential problem, possible causes and
remedies shown in the table below.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Have oven connected to a properly sized
electrical power supply by a qualified
electrician. Have an electrician check the
power supply, including the house circuit
breaker, wiring and fuses
Oven is not connected to the electrical
power. Power supply is not energized.
Nothing works
Plug on range is not completely inserted
in the electrical outlet. Burner holes on
the side of the burner may be clogged.
Make sure the unit is properly connected
to the power supply Remove the burner
heads and clean them. Check the
electrode area for burned-on food or
grease.
Top burners do not
light or do not burn
evenly
Burner bezel ports are clogged. Burner
ports or burner caps are not positioned
properly. Cooktop is being operated with
the wrong type of gas. Regulator is not
installed, is faulty, or is set for the wrong
type of gas.
Clean burner bezel ring ports with
straightened paper clip, needle, or wire.
Remove and carefully re-install burner
bezel and caps. Ensure that the type of
cooktop matches the natural gas supply.
Check installation, replace regulator, or
set regulator for proper gas.
Burner flames very
large and yellow.
Sparking but no flame Gas shut-off valve is in the ‘OFF’
Turn shut-off valve to the ‘ON’ position.
ignition.
position.
Power supply polarity is reversed. Igniters Have polarity corrected. Dry or clean
Igniters spark
continuously after
flame ignition.
are wet or dirty.
igniters.
Low gas supply pressure. Air intake holes
around knobs are obstructed.
Burner flame goes out
at low setting.
Contact gas company. Remove
obstruction.
Follow mode selection and clock settings
as specified in Oven Operation section of
the manual.
Oven will not heat
Oven settings are not corrected
Foods over-cooked or
under-cooked
Adjust time, temperature, or rack
position.
Incorrect cooking time or temperature.
‘Cracking’ or
‘Popping’ sound.
This is the sound of metal heating and
cooling.
This is normal.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY
This product has been manufactured by Duro Corporation Evergreen Place, City of
Industry, CA 91789
Duro Corporation disclaims all express warranties except for the following:
This warranty applies to products purchased and located in the United States. Products
purchased or located outside this area are excluded.
The warranty does not apply to damage resulting from abuse, accident, natural disaster,
loss of electrical power to the product for any reason, alteration, outdoor use, improper
installation, and improper operation, repair or service of the product by anyone other
than an authorized Duro Corporation, service agency or representative.
Warranties and Duration
Full warranty for Parts and Labor: 1 year
Implied warranties terminate upon expiration of the limited warranty. Some states do
not allow limitations on how long implied warranty lasts, so the above limitation may not
apply to your implied warranty.
Duro will pay for:
All repair labor and cost of replacement parts found to be defective due to material and
workmanship. Service must be provided by a Duro Authorized Service Agency during
normal working hours. For a Service Agency nearest you, please call 1-87-639-7264.
Duro will not pay for:
1. Service to instruct you on how to use your range to correct house wiring, replace or
repair house fuses. Service to correct the installation of your range.
2. Repairs when your range is used for other than normal, single-family household use
or when it is used in a manner that is contrary to published user or operator
instructions and/or installation instructions.
3. Cosmetic damage, including chips, dents, scratches or other damage to the finish of
your range, unless such damage results from defects in materials or workmanship
and is reported to Duro Corporation within 30 days from the date of purchase.
4. Costs associated with the removal from your home of your range for repairs. This
range is designed to be repaired in the home and only in-home service is covered by
this warranty.
5. Damage resulting from misuse, alteration, accident, abuse, fire, flood, acts of God,
improper installation, installation not in accordance with electrical, or use of
consumables or cleaning products not approved by Duro Corporation.
6. Service to repair or replace consumable parts. Consumable parts are not included
in the warranty coverage.
7. The removal and reinstallation of your range if it is installed in an inaccessible
location or is not installed in accordance with published installation instructions.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
8. This warranty is void if the factory applied serial number has been altered or
removed from your range.
9. Repairs to parts or systems resulting from unauthorized modifications made to the
appliance.
10.Expenses for travel and transportation for product service if your range is located in
a remote area where service by an authorized Duro Corporation servicer is not
available.
The warranty applies to appliances purchased and used for personal, family or
household purposes only.It does not cover appliances used for commercial applications.
Should the appliance be sold by the original purchaser during the warranty period, the
warranty shall extend to the new owner until the expiration date of the original
purchaser’s warranty period.
Warranty and Product Registration
Duro is not responsible for incidental or consequential damages. Under no
circumstances will Duro’s liability exceed the cost that you paid for the product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that
vary from state to state.
Whenever you call our customer service at 1-877-639-7264 (NEXRANGE) for technical
information and parts sales in the United States or to request service for your appliance,
please have your complete model number and serial number ready. The model and
serial number can be found on the product data plate. Please enter the information
requested in the spaces provided.
Model No. ________________________
Serial No. _________________________
Date Purchased ____________________
Date Installed ______________________
Purchased from ____________________
Address __________________________
Phone ___________________________
Note: You must provide proof of purchased or installation date for in-warranty service.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|