NETGEAR Network Card POE101 User Manual

Power Over Ethernet Adapters  
POE101  
Installation Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Package contents  
1
POE101Base unit  
POE101 Terminal unit  
DC Power cables  
Power adapter  
Category 5  
100 Mbps  
110v cord  
Ethernet cable  
POE101 installation guide,  
support information card &  
warranty/registration card  
Wall mount kit  
Power over Ethernet base unit  
Power over Ethernet terminal unit  
Localized AC power cable  
100~240 V AC to 24V DC 30W power adapter  
Two 2-foot DC power cables  
2-foot Ethernet cable  
Wall mount kit  
Installation Guide  
Warranty and support information cards  
Setup Requirements  
Two straight through Category 5 Ethernet cables:  
a short cable from an Ethernet hub or switch to the POE101 base unit and  
a second cable (up to 328 feet) for connecting from base unit to a terminal unit.  
These cables are not included in the NETGEAR POE101 packaging.  
2
A 5V DC powered NETGEAR access point .  
2 One set of POE101 adapters per access point is required.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connect a Matched Pair of  
POE101 Adapters  
Note: Use only in pairs of one base and one terminal unit only. Do NOT use two  
POE101 base units or two POE101 terminal units together.  
2
1. Connect a straight-through category 5 Ethernet cable (not included in the package) from  
the Ethernet switch or hub to the POE101 base units LAN IN” port.  
2. Plug in the the power to the POE base unit.  
Verify the POE101 base units LED lights are lit.  
3. Connect the a long straight-through category  
3
5 AWG24 Ethernet cable (not included in the  
package) from the POE101 base units LAN  
OUT” port to the terminal units LAN IN”  
POE101Base unit: LAN in, Power in  
port. Verify that the POE101 terminal unit has power by checking to see that the LED is lit.  
LAUT  
AN IN  
POE101 Base unit:  
"LAN OUT"  
POE101 Terminal unit:  
"LAN IN"  
Warning: Do not connect the base unit LAN OUT direct to any Ethernet device. The  
power output may damage the device.  
4. Connect the provided Ethernet cable from the  
POE101 terminal units LAN OUT” port to  
the wireless access points LAN port.  
5. Connect the DC power cable from the  
DC 5V OUT PWR  
LAN OUT  
POE101 terminal units PWR” port to the  
wireless access points power socket.  
POE101 Terminal unit: LAN out, Power Out  
Note: if you cannot plug in the DC power  
cable to the access point, use the other DC power cable. There are two DC power  
cables provided in the POE101 box. They both have a common plug head for the  
POE101 terminal unit’s “PWR” port. However, the other end of one has a the smaller  
plug head for North American use while the other cable has a bigger head for  
European use.  
3 By using a lower AWG numbered cable, you will get a better power transfer efficiency. However, the cable may be thicker.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Now you should see that power is provided to the NETGEAR wireless access point. If there is  
no power, please refer to the Troubleshooting section in this guide.  
Please see the illustration below. Your final connection should be similar.  
DSL  
modem  
Cable/DSL Web Safe  
Router RP614  
1
3
10/100 BASE-T Power over Ethernet  
MO EL  
Base  
10/100 BASE-T Power over Ethernet  
MO EL  
T
erminal  
D
D
POE 101  
POE 101  
POE101Base unit  
POE101 Terminal unit  
2
4
5
ME102 802.11b Wireless Access Point  
The total allowable distance should be less than 328 feet (100 meters)  
Calculate it from <=328 feet  
1
+
3
+
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Q: The base LED does not light up.  
A: Verify that the power supply connectors are properly connected.  
Q: The terminal LED does not light up.  
A: There are a couple of possibilities. Please check the following items in the sequence listed  
until everything works.  
1. Verify you are using a terminal unit.  
2. Verify that the POE101 base LED is lit.  
4
3. Verify that the long Ethernet cable is a straight-through category 5, AWG24 or less cable .  
4. Verify that the long Ethernet cable is inserted into the POE terminal “LAN IN” port.  
5. Unplug the DC power cable from the terminal unit. If the terminal LED lights up after  
being unplugged, then the problem is the access point. Please see the following question.  
Q: Both base and terminal LEDs light up. The access point still does not get power.  
A: Check these two conditions:  
1. Verify that you are using the correct DC power cable.  
2. Verify that the access point is a working unit. Plug in the power plug, which was provided  
in the access points original packaging. Verify that there is power to the access point.  
Q: What if I connect the wrong cable and connectors?  
A: If using a Category 5 Ethernet cable in a pure 10/100 Base-T environment, there will be no harm.  
Note: Do not use this product in a Gigabit or 10-Gigabit Ethernet network environ-  
ment. See the following question.  
Q: The POE101 does work with my Gigabit Ethernet network.  
A: This product is designed specifically for the Netgear access point. It may not work with  
other vendors products. Using it with a Gigabit Ethernet device may damage the device  
and void the product warranty.  
Note: With a correct configuration, POE101 works for 10/100 in a 10/100/1000  
switch. The speed is only in 10 or 100 megabit per second.  
4 It must be a full 8-wire cable. A 4-wire cable will not work. Look at the connector to see if it has 8 wires. To verify  
that it is a straight through type cable, check both ends of the RJ-45 connectors. The sequence of colors should be  
the same on each end.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Statement of Conditions  
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to  
make changes to the product described in this document without notice.  
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit  
layout(s) described herein.  
Certificate of the Manufacturer/Importer  
It is hereby certified that the NETGEAR Model POE101 Power over Ethernet adapters have been suppressed in  
accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some  
equipment (for example, test transmitters) in accordance with the regulations may, however, be subject to certain  
restrictions. Please refer to the notes in the operating instructions.  
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and  
has been granted the right to test the series for compliance with the regulations.  
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  
This device may not cause harmful interference.  
This device must accept any interference received, including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
EN 55 022 Declaration of Conformance  
This is to certify that the NETGEAR Model POE101 Power over Ethernet adapters are shielded against the generation  
of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is  
declared by the application of EN 55 022 Class A (CISPR 22).  
Canadian Department of Communications Radio Interference Regulations  
This digital apparatus (NETGEAR Model POE101 Power over Ethernet adapters) does not exceed the Class A limits  
for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian  
Department of Communications.  
Règlement sur le brouillage radioélectrique du ministère des Communications  
Cet appareil numérique (NETGEAR Model POE101 Power over Ethernet adapters) respecte les limites de bruits  
radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique  
du ministère des Communications du Canada.  
August 2002  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Specification  
AC power adapter  
Input: 100~240V AC 0.85A 50~60Hz  
Output: 24V DC 1.5A  
POE Base unit  
Power input: 24V DC  
10/100 Mb LAN IN  
10/100 Mb LAN OUT with 24V DC power  
POE Terminal unit  
Cables  
10/100Mb LAN IN with 24V DC power  
10/100Mb LAN OUT  
Power output: 5V DC 2.5A max.  
Category 5 with RJ-45 connectors for terminal to access point  
DC power cable for terminal unit to NETGEAR ME102 (North American version)  
DC power cable for terminal unit to all other NETGEAR 5V DC powered devices  
Localized AC power cable for wall to power adapter  
Technical Support  
Please refer to the Support Information Card that shipped with your product.  
Support Information  
Phone: 1-888-NETGEAR US and Canada only. For other support phone numbers in other  
countries please refer to your Support Card.  
E-mail: support@NETGEAR.com  
www.NETGEAR.com  
© 2002 by NETGEAR, Inc. All rights reserved.  
NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other  
countries.Other brand and product names are trademarks or registered trademarks of their  
respective holders. Information is subject to change without notice.  
*M-POE101NA-0*  
August 2002  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M - P O E 1 0 1 N A - 0  

Milwaukee Power Screwdriver 6580 20 User Manual
NEC Marine Instruments PX 42XM4G User Manual
NetComm Webcam NS370 User Manual
Outback Power Systems Power Supply FW X240 User Manual
Palsonic TV DVD Combo TFTV4839DT User Manual
Panasonic Computer Drive AJ HRW10G User Manual
Panasonic Computer Monitor BT LH80WE User Manual
Panasonic Network Card 2SC1473 User Manual
Panasonic Network Card 2SC6054G User Manual
Panasonic VCR AJ SD965 User Manual