Empowered by Innovation
Multibutton Telephone
User Guide
1093095
Rev 1, May 2006
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Reinstalling the Faceplate
To remove the faceplate (if installing a custom DESI label):
1. Put your finger in the recessed area under the
faceplate and lift off the faceplate.
To reinstall the faceplate:
1. Remove the old label, then insert the customized
replacement DESI label.
2. Press down on the faceplate as shown.
How To Use This Guide
When using the instructions in this user guide, you:
1. Dial a digit on the key pad. For example:
– For line keys, dial #RAL (#725).
2. Press a Feature Key or Fixed Function Key. For example:
– Press INTERCOM.
3. Push a soft key. For example:
– Push Clbk and hang up.
See A Quick Telephone Tour on the next page for a quick tour of your telephone’s layout and keys.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
the Display and Soft Keys
Alphanumeric Display
G
While your phone is idle, the display shows:
– The date and time, your name (see page 14), and your extension number.
– The idle menu soft key functions.
Menu Push to set up features on your phone (such as Call Forwarding).
Dir
Push to call a co-worker on the Intercom by selecting their name.
VM:xx Push to call your voice mailbox (xx is the number of new messages).
CL:xx Push to review your Caller ID log (xx is the number of new calls).
While your phone is ringing, the display shows:
– (If an Intercom call) Your caller’s name.
– (If an outside call with Caller ID) The name and number of the incoming caller.
G
G
G
While you are on a call, the display shows:
– Your caller’s name and number (if provided – see above).
– The functions of the soft keys that help you handle your call.
To adjust your display, push Menu + More (2 or 3 times) + Dsply + Cont
1
(contrast), Brght + Actv (active brightness), or Brght + Idle (idle bright-
ness). Volume adjusts the level. (1Not on 22-button.)
Soft Keys
– Use soft keys instead of dialing feature codes when handling your calls.
Your Feature Keys
G
G
To place or answer a call on your outside line keys:
– Press a line key to place or answer an outside call.
– Line keys flash red or green while ringing, are on steady red when busy.
– Your line keys are normally located on the first two rows of Feature Keys.
To make a Hotline key for a co-worker’s extension:
– Dial #57 + Press Feature Key + HOLD + INTERCOM + VOLUME up until you
see HOTLINE + HOLD + Dial co-worker’s extension number + HOLD +
SPEAKER twice to exit. (See the Telephone Feature Handbook for more Feature Key types you can set up.)
G
G
To call or Transfer your call to a co-worker:
– While on the call, press the Hotline Key. (The key lights red while your co-worker is busy, flashes red if in DND.)
– If you’re not on a call, pressing the Hotline Key places an Intercom call to your co-worker.
To check your Feature Key assignments:
– Press CHECK, then the Feature Key.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding the Ring/Message Lamp
The Ring/Message Lamp
– Two quick flashes (green): You have new (unreviewed) calls in your Caller ID log.
– Slow flash (green): A call is ringing your phone.
– Fast flash (red): There are new voice mail messages in your mailbox.
Setting Up Your Speed Dial Bin Keys
G
G
To store a Personal Speed Dial number in a bin key:
– Push Menu + Spd + Press bin key + HOLD + Dial line number (e.g., 1) on which the stored number should dial + HOLD
+ Enter the number you want to store + HOLD twice + Enter name (see page 14) + HOLD + SPEAKER to exit.
To call the stored number:
– Press bin key. (See the Telephone Feature Handbook for more on Speed Dial.)
Using the Fixed Function Keys
G TRANSFER
G INTERCOM
– Press + Dial co-worker’s extension to Transfer your call.
– Press + Dial co-worker’s extension + press V-MAIL to
transfer call to their mailbox.
– Press to dial a co-worker.
– On (green) while talking to voice mail or a co-worker.
– Flashes (green) during a Transfer or while an Intercom
call is on Hold.
G FLASH
– Lets you access features of your outside lines (if provided),
such as waiting call pickup.
G V-MAIL
– Calls your voice mailbox.
– On (red) while you call your mailbox.
– Flashes (red) during Call Screening broadcast.
G REDIAL
– To redial your last outside call, press REDIAL.
– To select one of your last 5 calls to redial, press
REDIAL + VOLUME + Dial soft key.
G DND
– Enables Do Not Disturb (when you don’t want to be
interrupted). Soft key selects mode.
– On (red) when Do Not Disturb is enabled.
G MUTE
– While on a call, MUTE turns off your handset or
Handsfree microphone.
G CONF
– While on a call, press to set up a Conference.
– On (green) while on a Conference.
– Flashes (green) if you put Conference call on Hold.
G SPEAKER
– Press to use Handsfree. Lift the handset for privacy.
– While on a handset call, press twice for Group Listen.
G HOLD
G VOLUME
– Puts your call on Hold.
– If idle, adjusts the display contrast.
– While on a call, adjusts the call volume.
– If Background Music is playing, adjusts the volume.
– While idle, turns Background Music on and off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Outside Calls
To answer an outside call:
1. Lift the handset.
2. If you are not automatically connected, press flashing line key.
– If you hear a call ringing a co-worker, dial ** and their extension number to pick it up.
To place an outside call:
1. Press a line key (normally located on your first two rows of Feature Keys).
2. Wait for outside dial tone, then dial your outside number.
OR
1. Press INTERCOM.
2. Dial 9.
– You may also be able to dial other codes (such as 101 or #901 for outside line 1).
3. Wait for outside dial tone, then dial your outside number.
To use Last Number Redial to quickly redial your outside call:
1. To redial your last outside call, press an idle (unlit) line key.
2. Wait for outside dial tone, then press REDIAL.
OR
1. To select a call from the last 5 you dialed, press REDIAL.
2. Press a VOLUME key to scroll through the list of the last 5 calls you dialed.
3. Lift the handset or press SPEAKER to call the displayed number.
To return a call in your Caller ID log:
1. Push CL + All.
2. Press a VOLUME key until the call you want to return displays.
3. Push Call.
To place a Personal Speed Dial call:
1. Press your Speed Dial bin key.
– To preselect a line, press a line key before your bin key.
To call a number stored in a system-wide Speed Dial bin:
1. Press INTERCOM.
2. Dial # + System Speed Dial bin (normally 201-299).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Intercom Calls To And From Co-Workers
To answer an Intercom call from a co-worker:
1. Do one of the following:
– If you hear two beeps, speak toward your phone.
– If you hear Intercom ringing, lift the handset.
To dial a co-worker over the Intercom:
1. Press INTERCOM.
2. Dial your co-worker’s extension number.
– If you hear Intercom ringing, wait for your co-worker to answer.
– If you hear two beeps, your call has voice-announced. Go ahead and speak.
– If you hear a single beep, your call has voice-announced but your co-worker has their handsfree
microphone muted (turned off).
3. (Optional) To make a voice-announced Intercom call ring, dial 1.
To call a co-worker using a Hotline Feature Key:
1. Press the Hotline key.
– The Hotline key is off when your co-worker is idle, on if busy, and flashing if in Do Not Disturb.
– See the Telephone Feature Handbook for more Feature Key types you can set up.
If the co-worker you call is busy:
1. For Camp-On, push Camp and wait on the line for them to become free.
OR
1. For Callback, push Clbk and hang up.
2. Wait for the system to call you back, then answer to have your call automatically go through.
To Page a co-worker over the telephone speakers:
1. Press INTERCOM.
2. Dial *10 for All Call Page, or *11 through *17 for page zones 1-7.
To leave a message for a co-worker:
1. Call your co-worker on the Intercom, then press V-MAIL.
To call your own mailbox:
1. Press V-MAIL or push VM:xx.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Place A Call On Hold
To place your call on System (Regular) Hold:
(Your co-workers can pick up calls you place on System Hold.)
1. Press HOLD.
– While an outside call is on Hold, the line key will flicker (green).
– While an Intercom call is on Hold, your INTERCOM key will flicker (green).
– A call you leave on Hold too long will recall to you. If you don’t answer the recall from an outside
call, it will then ring your co-workers.
– Your co-workers cannot pick up an Intercom call you place on Hold.
To place your outside call on Exclusive Hold:
(Your co-workers cannot pick up calls you place on Exclusive Hold.)
1. Press HOLD twice.
To pick up an outside call on Hold:
1. Press the flashing line key.
To pick up an Intercom call on Hold:
1. Press the flashing INTERCOM key.
Transfer A Call To A Co-worker
To Transfer your call to a co-worker:
(If you have a Hotline Feature Key for your co-worker, press it and skip to step 3.)
1. While on a call, press TRANSFER.
– To Transfer the call directly to your co-worker’s mailbox, press V-MAIL before going to step 2.
2. Dial your co-worker’s extension number.
3. Do one of the following:
– If you did not press V-MAIL after step 1, you can alternately press it here to send the call to
your co-worker’s mailbox.
– Announce the call and hang up.
– Hang up to have the Transfer go through unannounced.
4. The transferred call will recall to you if it is not picked up.
– If you don’t answer the recall, the call will ring your co-workers.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Up A Conference (Telephone Meeting)
To set up a telephone meeting:
1. Place or answer your first call.
2. Press CONF.
3. Place or answer your next call.
4. Press CONF again to set up the Conference.
– Repeat steps 2 through 4 to add additional callers to your Conference.
– You can add either Intercom or outside callers.
– If you hear an error tone after trying to add another party, your Conference is full.
– To place a Conference on Hold, press HOLD. To reinstate the Conference, press CONF.
Forward Calls To A Co-Worker or Voice Mail
To forward (reroute) your calls to a co-worker or voice mail:
1. While idle, push Menu + Cfwd.
2. For the Call Forwarding Type, push one of the following:
– Immed for Call Forwarding Immediate.
– RNA for Call Forwarding when Not Answered.
– B/NA for Call Forwarding when Busy or Not Answered.
– More + Offp for Call Forwarding Off Premises. See the Telephone Feature Handbook for more.
– More + AME for Answering Machine Emulation. See the IntraMail Feature Handbook for more.
– More + Msg for Selectable Display Messaging. See the Telephone Feature Handbook for more.
– More + None to cancel Call Forwarding.
3. For the Call Forwarding Destination, do one of the following:
– Dial a co-worker’s extension number.
– Dial 0 for the operator.
– Press V-MAIL to forward your calls to your mailbox.
4. For the Call Forwarding Mode, do one of the following:
– Push All to forward all calls.
– Push Line to forward just outside calls.
– Call Forwarding will only forward outside calls that directly ring your phone (such as calls trans-
ferred from a co-worker or from your Automated Attendant).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dialing By Name (Directory Dialing)
To dial a co-worker or outside call by selecting from a group of names:
1. Push Dir.
2. Select a Directory Dialing type:
– To call a co-worker, push Ext.
– To call a Personal Speed Dial number, push Pers.
– To call a System Speed Dial number, push Cmpy.
3. Press a VOLUME key to scroll through the list of names.
– Before pressing VOLUME, you can narrow your search by dialing the first letter of the name +
1, 2, or 3.
4. Push Dial to call the displayed name.
– Press SPEAKER to exit anytime without dialing.
Change Your Ring Tones
To change the ring tones on your phone:
1. Push Menu + More + Ring + Cnfg.
2. Select the type of ringing you want to customize:
– For Intercom ringing, push Icm.
– For Hold and Transfer recall ringing, push Rcl.
– For Ring Group ringing, push Rgrp.
– For type A Feature Key Ringing, push More + A.
– For type B Feature Key Ringing, push More + B.
– For type C Feature Key Ringing, push More + C.
– To set your phone’s ringing back to the system default, push More + More + Dflt.
3. Dial the digit for the new ring tone (0-9).
– You’ll hear the new ring tone as you dial each digit.
4. Do one of the following:
– Push Save to save your selection.
– Push Cncl to exit without changing your ring tone.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Ring Tones For Specific Feature Keys
To turn Feature Key ringing on and off:
(These steps apply to line keys, Call Coverage keys, and Group Call Pickup keys. See the Telephone
Feature Handbook for more on setting up Feature Keys.)
1. Do one of the following:
– For line keys, dial #RAL (#725).
– For Call Coverage keys, dial #RAC (#722).
– For Group Call Pickup keys, dial #RAP (#727).
2. Make a note of the Feature Key lamps.
– The lamps in the key type you selected will illuminate.
3. Press the line key to change to ringing. The flash rate indicates the ringing mode:
– On green for Immediate Ring.
– Slow flash green for Night Ringing (line keys only).
– Fast flash green for Delayed Ringing.
– On red for no ringing.
4. Press SPEAKER to exit.
To change the ringing sound for individual Feature Keys:
(These steps apply to line keys, Call Coverage keys, and Group Call Pickup keys. See the Telephone
Feature Handbook for more on setting up Feature Keys.)
1. Push Menu + More + Ring + Key.
2. Do one of the following:
– For line keys, push Line.
– For Call Coverage keys, push Cck.
– For Group Call Pickup keys, push Pkup.
3. Select a Feature Key.
4. Dial one of the following to select the ring sound:
– For two mid-pitch rings (type A), dial 1.
– For two high-pitch rings (type B), dial 2.
– For two very high-pitch rings (type C), dial 3.
5. Press SPEAKER to exit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing And Using a Headset
To install an optional headset:
1. Plug the headset cord into the headset jack on the bot-
tom of the telephone.
2. The headset cord routes through the upper channel on
the right side of the telephone base.
To set up a headset Feature Key:
1. Dial #KP (#57).
2. Press the Feature Key you want to assign + HOLD.
3. Press INTERCOM.
– INTERCOM flashes (red).
4. Press a VOLUME key until you see HEADSET.
5. Press HOLD + SPEAKER twice to exit.
To turn the headset mode on and off:
1. Press your Headset Feature Key.
– The headset key is on while in the headset mode; off while in the normal handset mode.
– You can optionally dial #HS to turn the headset mode on and off.
To use your headset:
1. While in the headset mode, you can do the following:
– Press a line key to place or answer an outside call.
– Press INTERCOM to dial a co-worker on the Intercom.
– While on a call, press SPEAKER to hang up.
2. Keeping the above three things in mind, process calls normally using the convenience of a headset.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using A DSS Console
For more call handling power and flexibility, the DSS Console pro-
vides 60 additional Feature Keys as well as three Speed Processing
Keys along the bottom. (For more on setting up Feature Keys, see
the Telephone Feature Handbook.)
To use the Speed Processing Keys:
The ANSWER Key
1. Press ANSWER to answer any call ringing your phone.
The RELEASE Key
1. Press RELEASE to hang up (disconnect) your call.
The TRANSFER Key
1. Press TRANSFER to Transfer your call instead of using
the key on your telephone.
Special Features For Attendants
If you are an attendant (normally extension 300), you have the following unique features:
Attendant Call Queuing
If also enabled as an operator, the last Feature Key on your phone is an Operator Call Key. This means
you are never busy for Intercom calls – they “stack up” under this key instead.
Barge In
You can break into a co-worker’s active call.
Direct Line Access and Forced Line Disconnect
Dial a code to directly access a specific outside line. You can optionally disconnect the call as well.
Line Queuing / Line Callback
Dial a code to wait for a busy outside line to become free.
Night Service / Night Ring
Put the system in the night mode (for after-hours answering). This requires a System Night Feature Key.
Removing Lines and Extensions from Service
Remove problem lines from service – and return them to service once corrected.
13
(See the Telephone Feature Handbook for more on these features.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Your Extension’s Name
To program your extension’s name:
1. Push Menu + More + More + Name.
2. Enter the name following the Name Programming Chart below + Press HOLD.
– Also use this procedure to program Personal Speed Dial names and Display Messages.
Name Programming Chart
Key
1
1 Press
2 Presses 3 Presses 4 Presses 5 Presses 6 Presses 7 Presses 8 Presses 9 Presses
&
-
/
C
F
I
‘
a
d
g
j
1
b
e
2
A
B
E
H
K
N
Q
U
X
:
c
f
2
3
4
5
6
r
3
D
4
G
h
k
i
5
J
L
l
6
M
O
R
V
Y
0
m
S
t
n
p
u
w
o
q
v
x
7
P
s
z
7
9
8
T
8
y
9
W
Z
0
Space
*
*
#
#
HOLD
SPEAKER
VOLUME
CLEAR
Save name.
Exit name programming.
When editing your name, VOLUME up moves the cursor right. VOLUME down moves it left.
Clears (erases) your name.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional User Programmable Features
To program a feature, dial # and the feature’s code. For example, to enable incoming Paging, dial # + V P Y, then SPEAKER
to hang up. Normally, Call Forwarding Clear All, System Speed Dial, and Time and Date are only available to extension 300.
For more on the features, see the Telephone Feature Handbook.
User Programmable Features Chart
Feature
Mnemonic Numeric
Operation
Call Forwarding Clear All
#CC + Y to clear (cancel) forwarding or N to exit without clearing +
SPEAKER to exit.
#CC
#22
Hotline Key Assignment
Off-Hook Signaling
#HL + Press flashing Hotline key + Enter extension for new Hotline
partner + HOLD + Program another Hotline key or SPEAKER to exit.
#HL
#45
#OHS + Select mode (1 = Outside line, 2 = Calls from Hotline partner,
3 = Intercom) + Select option (see below) + SPEAKER to exit.
Outside line: 1 = Camp On tone, 2 = Off Hook Ringing, CLEAR = None.
Hotline partner: 1 = Camp On, 2 = Voice Over, CLEAR = None.
Intercom: 1 = Camp On, 2 = Voice Over, CLEAR = None.
#OHS
#647
Paging (Incoming)
#VP + Y to enable or N to disable + SPEAKER to exit.
#VP
#87
Prime Line Assignment
#PLA + Press one of your flashing programmable keys, INTERCOM,
or CLEAR for none + SPEAKER to exit.
#PLA
#752
Feature Key Assignment
#KP + Press key you want to program + HOLD + INTERCOM + Press
VOLUME to select key option + HOLD + (Enter any additional data +
HOLD – see the Telephone Feature Handbook) + SPEAKER twice to exit.
#KP
#57
Ringing Line Preference
Speed Dial
#RLP + Y to enable or N to disable + SPEAKER to exit.
#RLP
#SP
#757
#77
#SP + Dial bin number or press bin key + HOLD + Dial outside line (e.g.,
1), Line group (e.g., 90-98), or INTERCOM for Intercom feature + HOLD
+ Number to store + HOLD twice + Name + HOLD + SPEAKER to exit.
(System bins are 201-299. Personal bins are 701-720.)
Time and Date
#TD + Enter time in 24-hour clock using hours (2 digits), minutes (2
digits) and seconds (2 digits) + HOLD + Enter date using month (2
digits), day (2 digits) and year (4 digits) + HOLD + SPEAKER to exit.
#TD
#VA
#83
#82
Intercom Voice Announce
(for Incoming Intercom Calls)
#VA + V for voice announce or R for ring + SPEAKER to exit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling (Logging Into) Your Mailbox
Voice Mail lets callers leave recorded messages for you and lets you leave recorded messages for co-workers.
Messages get stored in each person’s mailbox. To listen to your messages or use other voice mail features, you
call your mailbox and access the Main Menu. When you have new messages, your Ring/Message lamp flashes
(red) and your VM:xx soft key shows the number of new messages.
The Automated Attendant can answer your company’s calls with a recorded message and give dialing instruc-
tions for callers to follow.
To log into your mailbox from your own phone:
1. Do one of the following:
– Press V-MAIL.
– Push VM:xx (xx is the number of new messages in your mailbox).
To log into your mailbox from a co-worker’s phone:
1. Press INTERCOM and dial 700.
– 700 is the voice mail “master number.”
2. Dial your own extension number.
– If you share a Group Mailbox with co-workers, pressing V-MAIL on your phone or their phone
logs you into the same shared mailbox.
From outside, to log onto your mailbox after calling your company’s Automated Attendant:
1. Dial # (for remote logon).
2. Dial your own extension number.
From outside, to log onto your mailbox if you have a direct line to your phone:
(This requires custom programming and your phone must be forwarded to voice mail.)
1. When voice mail picks up, wait for your greeting to start.
2. Dial # to stop the greeting.
3. Dial # and your own extension number.
From outside, to leave a message for a co-worker after calling your company’s Automated Attendant:
1. Dial * (for quick message).
2. Dial your co-worker’s extension number.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Voice Mailbox Basics
Review these basic features before using your mailbox for the first time.
To record a greeting for your mailbox:
(Callers hear your greeting before leaving you a message.)
1. Press V-MAIL or push VM:xx.
2. Push Greet.
– If you want calls from your company’s Automated Attendant to go directly to your mailbox (with-
out first ringing your phone), dial the letter O (6) before the next step.
3. Push Gr1, Gr2 or Gr3 to select which of the three available greetings you want to be active.
4. Do one of the following:
– Push Lstn to listen to your greeting (if recorded).
– Push Rec to record a new greeting.
– Push Erase to delete your greeting (and use the built-in prerecorded greeting).
– Push Exit to exit without changing your greeting.
To record a name for your mailbox:
(Callers may hear your recorded name before leaving you a message.)
1. Press V-MAIL or push VM:xx.
2. Dial RN (76).
3. Do one of the following:
– Push Lstn to listen to your name (if recorded).
– Push Rec to record a new name.
– Push Erase to erase your name (and use your extension number instead).
– Push Exit to exit without changing your name.
To enter a security code for your mailbox:
(A security code prevents unauthorized access to your mailbox.)
1. Press V-MAIL or push VM:xx.
2. Dial OP (67) and push Sec..
3. Do one of the following:
– Enter a new security and push OK.
– Push Erase to erase your security code.
– Push Exit to exit without changing your security code.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
More Mailbox Features
When you log onto your mailbox, you get your mailbox main menu of options. These additional features are avail-
able from your main menu.
To record and send a message to a co-worker:
1. Press V-MAIL or push VM:xx.
2. Push Rec.
3. Enter the message recipient’s mailbox number.
4. Do one of the following:
– To begin recording your message, push Cont.
– To select a different message recipient, push Mbox.
5. Record your message and do one of the following:
– Push Done to send your message.
– Push Pause and Resume to pause and resume your recording.
– Push Cncl to cancel your recording without sending it.
To listen to your messages:
1. Press V-MAIL or push VM:xx.
2. Push Lstn..
3. While listening to your message, you can do one of the following:
– Dial RE (73) to record a reply for the message sender.
– Dial MF (63) to forward the message to a co-worker.
– Dial MC (62) to make a return call to the message sender.
– Dial TI (84) to hear the time and date the message was sent.
– Dial SA (72) to save the message in your mailbox.
– Push Erase to erase the message.
– Push Next to listen to the next message.
– Dial B (2) to back the message up a few seconds, or G (4) to go ahead a few seconds.
– Push Rpt to repeat the message from the beginning.
– Dial * to pause and resume listening.
– Push Exit to exit the message listen mode.
– Listen to a specific message list (dial 1N for new messages, 1S for saved messages, or 1A for
all messages). This option is also available from your mailbox main menu.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
More Mailbox Features
After listening to a message, to have voice mail announce the message sender, as well as the
time and date the message was sent to you:
1. Press V-MAIL or push VM:xx.
2. Push Time.
3. Do one of the following:
– Push On to turn Auto Time Stamp on.
– Push Off to turn Auto Time Stamp off.
– Push Exit to exit without changing the current setting.
To be notified (called) at your pager, cell phone, or home office when you have new messages:
1. Press V-MAIL or push VM:xx.
2. Dial OP (67) and push Notif.
3. Do one of the following:
– Push On to turn notification on.
– Push Off to turn notification off.
– Push Chnge to change your notification settings.
– Push Exit to exit without changing the current setting.
(The following steps apply if you have turned notification on for the first time or have pushed Chnge.)
4. Dial the notification start hour. The entry is 2 digits (01-12) + A (2) for AM or P (7) for PM.
5. Dial the notification stop hour. The entry is 2 digits (01-12) + A (2) for AM or P (7) for PM.
6. Select the notification type:
– Push Num to have voice mail notify you at your cell phone or home office.
– Push Pager to have voice mail notify you on your digital pager.
7. Dial your pager, cell phone, or home office number + Push OK.
– For help with the number you should dial, see your System Administrator.
8. When you have a new message, voice mail will do one of the following:
– For a pager, call your pager and display digits that let you know you have a new message.
– For a cell phone or home office, call the number and announce the message when you answer.
To play a recorded help message while you are handling your messages:
1. Dial 0.
– This option is not always available.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
System Administrator Options
The following administrative features are available only at the System Administrator’s extension (normally 300).
See the IntraMail Feature Handbook for more on each of the underlined features.
To use the System Administrator options:
1. At extension 300, press V-MAIL or push VM:xx.
2. Dial SA.
3. For the System Administrator recording and routing options, do one of the following:
– To record an Instruction Menu message (Automated Attendant greeting), push Instr + Dial the
mailbox for the greeting (001 - 008) + Push Lstn to listen, Rec to record, or Erase to erase.
– To record an Announcement Message, push Annc + Dial the mailbox for the message (009 -
016) + Push Lstn to listen, Rec to record, or Erase to erase.
– To activate Answer Schedule Override (alternate Automated Attendant answering), dial O (6) +
Dial the Answer Table Number (1 - 8} + Dial the Override Mailbox number (normally 001 - 008)
+ Push On or Off (to turn the feature on or off) or Mbox {to change the override mailbox}.
– To record a Message On Hold, Dial 1 + Push Lstn to listen, Rec to record, or Erase to erase.
OR
3. For the System Administrator mailbox maintenance options, do one of the following:
– Push Subs + Dial extension whose mailbox you want to maintain (e.g., 301).
– To Erase All Messages in the mailbox, push Msgs.
– To erase the mailbox Greeting, push Greet.
– To erase the Mailbox Name, push Name.
– To record a new Mailbox Name, dial N (6) + Push Lstn to listen, Rec to record, or Erase to erase.
– To use Mailbox Security Code Delete to delete the mailbox Security Code, dial S (7).
NEC Unified Solutions, Inc.
4 Forest Parkway, Shelton, CT 06484
TEL: 203-926-5400 FAX: 203-929-0535
(1093095)
Empowered by Innovation
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|