MULTIMEDIA PROJECTOR
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOKING IN THE INDEX
Be Sure to Read before Use.
This section describes important safety and operating instructions.
SAFETY INSTRUCTIONS
BEFORE USE
Learning the Names of Parts
This section describes names of parts. Be sure to read this section.
Setting up the Projector
This section describes preparations for installing the projector. Be sure
to read this section.
INSTALLING THE
PROJECTOR
Projecting an Image from the Computer
This section describes the procedure for projecting an image from the
computer connected to the projector.
PROJECTING AN IMAGE
FROM THE COMPUTER
Learning the Functions Available during Projection
This section describes the useful functions available during projection.
Read this section as required.
USEFUL FUNCTIONS AVAILABLE
DURING PROJECTION
Projecting an Image from AV Equipment
This section describes the procedure for projecting an image from a
digital still camera, digital camcorder, or other AV equipment.
PROJECTING AN IMAGE
FROM AV EQUIPMENT
Menu Functions
This section describes the functions listed in the menus.
SETTING UP FUNCTIONS
USING MENUS
Projector Maintenance
This section describes how to clean the projector and replace
consumable parts.
MAINTENANCE
Troubleshooting
Please read this section if your projector is not performing properly.
TROUBLESHOOTING
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPPLIED MANUALS AND
SYMBOLS USED IN THIS MANUAL
Supplied Manuals
User’s Manual
Quick Start Guide
This manual provides detailed information This guide shows an outline flowchart of
about how to use this projector. Read this the work necessary to make a presentation
manual thoroughly to make the most of using this projector.
this projector and ensure safety.
Symbols of Buttons
This projector can be operated using buttons on the remote control or main unit. The
remote control allows you to use all functions of the projector; however, the buttons on the
main unit allow you to use only often-used functions.
In this manual, buttons are indicated by symbols. The symbol of a button on the remote
control is shown in
and the symbol of a button on the main unit is shown in
.
At the beginning of each operational procedure, the position of the button used to perform
the operation is described with an illustration.
1
Press the [MENU] button.
The Menu window appears.
- To close the Menu window, press
the [MENU] button again.
Remote control
Top control
Indicates the button on the control on the main unit.
Indicates the button on the remote control.
Symbols Used in This Manual
Meanings of the following symbols used in this manual are as follows:
A precaution about operation or restriction is given here.
An important matter that you should be aware of before operation or a useful tip is
provided here.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
USES OF THIS PROJECTOR................2
PROJECTING AN IMAGE FROM
AV EQUIPMENT ...................................42
Connecting the Projector to AV
LOOKING IN THE INDEX ......................3
Equipment................................................42
Starting Projection.......................................44
Adjusting the Image ....................................48
SUPPLIED MANUALS AND SYMBOLS
IN THIS MANUAL...................................4
TABLE OF CONTENTS .........................5
SAFETY INSTRUCTIONS......................6
SETTING UP FUNCTIONS USING
MENUS .................................................49
Using Menus...............................................49
Display Settings Menu ................................52
Image Adj. Menu.........................................62
System Settings Menu................................69
BEFORE USE.......................................14
Supplied Accessories .................................14
Part Names.................................................15
MAINTENANCE....................................75
Cleaning the Projector ................................75
Cleaning and Replacing the Air Filter .........76
Replacing the Lamp....................................77
INSTALLING THE PROJECTOR.........20
Determining the Distance to the Screen .....20
PROJECTING AN IMAGE FROM
TROUBLESHOOTING..........................79
Understanding the Warning Lamp Flash
THE COMPUTER .................................23
Connecting the Projector to the Computer..23
Starting Projection.......................................26
Adjusting the Image ....................................30
Turning Off the Projector.............................35
Setting up the Power Management
Patterns....................................................79
Symptoms and Solutions ............................80
APPENDIX............................................84
Computer Signal Types...............................84
Relationship between Screen Size and
Function ....................................................36
Projection Distance .................................85
Menu Configuration.....................................86
Glossary......................................................88
Specifications..............................................90
USEFUL FUNCTIONS AVAILABLE
DURING PROJECTION .......................37
Blacking Out an Image Temporarily............37
Making an Image Larger/Smaller................38
Showing the Elapsed Time .........................39
Indicating a Position with a Spotlight ..........39
Freezing the Picture....................................40
Muting the Sound/Adjusting the Volume.....40
Operating the Mouse Using the Remote
* “Display Settings Menu”, “Image Adj. Menu”
and “System Settings Menu” have detailed
contents on their title pages.
Control .....................................................41
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Before operating this projector, read this manual thoroughly and operate the projector
properly.
This projector provides many convenient features and functions. Operating the projector
properly enables you to manage those features and maintains it in better condition for a
considerable time.
Improper operation may result in not only shortening the product-life, but also
malfunctions, fire hazard, or other accidents.
If your projector seems to operate improperly, read this manual again, check operations
and cable connections and try the solutions in the “Troubleshooting ” section in the end of
this booklet. If the problem still persists, contact the dealer where you purchased the
projector or the service center.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE
EXCEPT LAMP REPLACEMENT.
QUALIFIED SERVICE PERSONNEL.
REFER SERVICING TO
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of
Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
Safety Precaution
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
- This projector produces intense light from the projection lens. Do not stare directly into
the lens as possible. Eye damage could result. Be especially careful that children do
not stare directly into the beam.
- Install the projector in a proper position. If not, it may result in a fire hazard.
- Provide appropriate space on the top, sides and rear of the projector cabinet for
allowing air circulation and cooling the projector. Minimum clearance must be
maintained. If the projector is to be built into a compartment or similarly enclosed, the
minimum distances must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your projector, and can also be
dangerous.
- Do not put any flammable object or spray can near the projector, hot air is exhausted
from the ventilation holes.
- If the projector is not to be used for an extended time, unplug the projector from the
power outlet.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
All the safety and operating instructions shoud be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector
from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent
damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may cause
hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall,
causing serious injury to a child or adult, and serious damage to the projector. Use only
with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or
shelf mounting should follow the manufacturer's instructions, and should use a mounting
kit approved by the manufacturers.
An appliance and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the appliance
and cart combination to overturn.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to
insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom
opening should not be blocked by placing the projector on a bed, sofa, rug, or other
similar surface. This projector should never be placed near or over a radiator or heat
register.
This projector should not be placed in a built-in installation such as a book case unless
proper ventilation is provided.
Never push objects of any kind into this projector through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-conditioning equipment.
This projector should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this projector where the
cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a need for
service.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer that have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock, or injury to
persons.
Upon completion of any service or repairs to this projector, ask the service technician to
perform routine safety checks to determine that the projector is in safe operating
condition.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the
country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by
the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is
a safety feature to be sure that the plug will fit into the power
outlet. Do not try to defeat this safety feature. Should you
be unable to insert the plug into the outlet, contact your
electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
NOTE FOR CUSTOMERS IN THE US
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY
AND MUST BE RECYCLED OR DISPOSED OF ACCORDING
TO LOCAL, STATE OR FEDERAL LAWS.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission Notice
Multimedia Projector, Model : SX50
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The cable with the ferrite core provided with the projector must be used with this
equipment in order to comply with Class B limits in Subpart B of Part 15 of the FCC
rules.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise
specified in the instructions. If such changes or modifications should be made, you
could be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
Canadian Radio Interference Regulations
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LAMP HANDLING
PRECAUTIONS
This projector uses a high-pressure mercury lamp which must be handled carefully and
properly as mentioned below.
• A lamp may explode with a loud sound or burn out due to a shock, scratch, or expiration of
lifetime.
• The lamp life may differ from lamp to lamp and according to the environment of use. There is
not guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their life
in a shorter period of time than other similar lamps.
• A lamp gradually becomes darker with time of use.
• If the projector indicates that the lamp should be replaced (i.e., the LAMP REPLACE indicator
lights up twice), chances of explosion become higher. Replace the lamp with a new one
immediately.
• Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
IF A LAMP EXPLODES
If a lamp explodes, the gas and broken shards may scatter inside the projector
and they may come out of the exhaust vent. The gas contains toxic mercury.
Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or
mouth, consult the doctor immediately.
If a lamp explodes, its shards may scatter inside the projector. Ask the Canon
service representative to clean and check the inside of the projector and
replace the lamp.
DISPOSAL OF WASTE LAMP
Dispose of the mercury lamp of the projector according to the local regulation
just like the fluorescent lamp.
CARRYING/TRANSPORTING THE
PROJECTOR
This projector is a precision machine. Do not give a strong shock to the projector or turn it
down.
Thoroughly read “Use Caution When Carrying or Transporting the Projector” below and install
the lens cap before carrying the projector. When transporting the projector by train or airplane,
use a highly crashworthy transport case.
Use Caution When Carrying or Transporting the Projector
The carrying bag is intended for protection from dust and scratches on the surface of the
cabinet, and it is not designed to protect the projector from external shocks. When carrying the
projector with it put in the carrying bag, do not give a shock to it, drop it, or place anything on it.
Do not transport the projector through a courier or transport service with the carrying bag. The
projector can damage.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION PRECAUTIONS
Ensure that the projector is installed with a minimum distance of 1 m (3.3') from its left,
right, rear, and top panels to the neighboring object such as a wall.
Pay Attention to Hot Air from Exhaust Vent
Hot air is exhausted from the exhaust vent. Do not place any object near the exhaust vent.
• Do not put any spray can near the vent.
The internal pressure increases due to heat,
resulting in explosion.
•
Do not put any metallic object. It may become
hot, resulting in an accident or injury.
• Do not put anything such as a plant pot.
• Do not put anything that may deform or
deteriorate due to heat.
• Do not put an audience seat near the
exhaust vent.
Do not put anything that may deform or discolor due to heat on the projector. The area
around the exhaust vent and the cabinet above the exhaust vent become hot. Do not touch
these areas, or you may get burnt. Especially, keep children away from these areas.
Do Not Use in the Following Environments
Do not install the projector in a humid or dusty place or a place where there is much oily
smoke or cigarette smoke. Optical parts such as a lens and mirror are stained, resulting in
poor picture.
Do not use the projector in a place where the temperature becomes very high or low.
°
°
°
°
Operating temperature: +5 C to +35 C Storage temperature: -10 C to +60 C
Pay Attention to Condensation
If the projector is carried from a cold place to a warm place or the room temperature is
raised rapidly, dew may form on the lens and mirror due to the moisture in the
atmosphere, resulting in a blurred picture. Wait until dew evaporates and a normal picture
is shown.
Install the Projector at Proper Position
Install the projector properly. Improper installation may cause troubles and accidents.
• Do not tilt the projector more than 20
degrees above and below.
• Do not point the projector up.
• Do not point the projector down.
20 degrees
•
Do not put the projector on either side.
20 degrees
Do not tilt the projector more than 20 degrees above and below.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USE
Supplied Accessories
Check whether the following accessories are supplied with the projector.
Remote control
Computer connection cable
(DVI/Mini D-sub, 15-pin) (1.8m/5.9')
Batteries (type AAA, two)
for remote control
Power cord (2m/6.6')
USB cable (1.8m/5.9')
Component cable
(RCA/Mini D-sub, 15-pin) (0.4m/1.3')
User’s Manual
Quick Start Guide
Warranty card
Lens cap strap
Carrying bag (P12)
Lens cap
Tie the lens cap to the projector
with the supplied strap. For the
procedure, see page 92.
• When the projector is not in use, attach the lens cap to protect the lens from dust
and other foreign objects.
• Be sure to attach the ferrite core to the power cord.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Main Unit of Projector
1 Focus Ring (P30)
2 Infrared Remote Receiver (P16)
3 Zoom Lever (P30)
4 Lens
Front
2
1
7
5 Lens Cap
Be sure to remove the lens cap
during projection. The cap can
deform or fire can occur.
4
6 Speaker
7 Terminals and Connectors (P19)
8 Power Cord Connector (P19)
9 Anti-theft lock hole
9
5
8
6
3
Back
1 Exhaust Vent
Do not block this vent. Troubles or
fire can result.
2
2 Top Control (P18)
1
1 Adjustable Foot Lock Button (P22)
2 Adjustable Foot (P22)
3 Lamp Cover (P77)
Bottom
1
4 Air Intake Vent
5 Air Filter (P76)
6 Lens cap strap insertion hole
2
3
6
5
Do not block this vent. Troubles or
fire can result.
4
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Infrared Remote Emitter
Sends a signal to the infrared remote
receiver on the main unit.
Remote Control
1
2 POWER button (P27, 45)
Turns the projector on or off.
5
3 MENU button (P50)
Displays a menu.
3
6
2
4
4 COMPUTER-1 button (P28, 46)
Selects the image input from the DVI-I/RGB
IN-1 terminal.
Pressing this button continuously allows you
to select an input signal (DIGITAL RGB or
ANALOG RGB-1).
7
8
9
5 COMPUTER-2 button (P28, 46)
Selects the image input from the RGB IN-2/
COMPONENT IN/RGB OUT terminal.
Pressing this button continuously allows you
to select an input signal (ANALOG RGB or
COMPONENT).
10
11
12
14
6 VIDEO/S button (P46)
Select the image input from the VIDEO IN
terminal or S-VIDEO terminal.
Pressing this button continuously allows you
to select input signals (VIDEO or S-VIDEO).
15
13
Remote Control Operating Range
Point the remote control to the infrared remote
receiver whenever pressing any button. The maxi-
mum operating range is about 5 m (16.4' ) and 30o
in front of the infrared remote receiver.
17
18
16
19
21
20
30o
5m (16.4')
Within 5 m (16.4' ) and
30o in front of infrared
remote receiver
30o
The remote control may be inoperative in the following cases:
• When there is an obstacle between the remote control and main unit.
•
When the infrared remote receiver on the main unit is exposed to direct sunlight or
strong light of lighting equipment.
• All operations of the projector can be controlled with the remote control.
• The remote control uses infrared light.
• When you use two projectors at the same time, you can change the channel
settings to prevent the two remote controls from interfering with each other.
(P72)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7 KEYSTONE button (P31)
Corrects keystone distortion.
14VOL button (P40)
Adjusts the sound volume. Pressing [+] turns
the volume up and pressing [-] turns the
volume down.
8 AUTO PC button (P29)
When ANALOG RGB-1 or ANALOG RGB-2
is selected, performs the auto PC adjustment
to adjust the tracking, total number of dots,
and image position automatically.
15D.ZOOM button (P38)
Zooms the image in or out. Pressing [+]
enlarges the image and pressing [-] reduces
the image.
9 OK button (P51)
Determines the item selected from the menu
just like the left button of a mouse (USB
connection).
16IMAGE button (P34)
Switches image modes (image qualities).
17MUTE button (P40)
Mutes the sound temporarily.
10POINTER button (P50)
Selects the upper, lower, left, or right item in
the menu. Also moves the mouse cursor
(USB connection).
18NO SHOW button (P37)
Turns the picture into a black image.
11 SPOT button (P39)
Performs the spot light function.
19FREEZE button (P40)
Freezes the projected picture.
12R-CLICK button (P41)
Acts as the right button of a mouse (USB
connection).
20P-TIMER button (P39)
Displays the time elapsed since this button
was pressed (this button can be used to
manage the presentation time).
13PAGE button
Acts as the Page Up and Page Down keys on
the computer keyboard (USB connection).
Pressing [ ] scrolls to the previous page and
pressing [ ] scrolls to the next page.
21LIGHT button
Turns on or off the remote control buttons.
Installing Remote Control Batteries
Install batteries.
Replace the compartment
lid.
3
Open the battery
compartment lid.
Slide the lid with it pressed
down.
2
1
Insert new two AAA-size
batteries in the compartment
with the + and – poles
positioned correctly.
If all buttons on the remote control do not light when the [LIGHT] button is pressed, or
buttons are inoperative when you attempt to operate the projector, replace new batteries.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Control
2
9
1
10
11
4
5
6
7
3
8
1 POWER button (P27, 45)
Turns the projector on or off.
7 AUTO PC button (P29)
When ANALOG RGB-1 or ANALOG RGB-2
is selected, performs the auto PC adjustment
to adjust the tracking, total number of dots,
and image position automatically.
2 KEYSTONE button (P31)
Corrects keystone distortion.
3 MENU button (P50)
Displays a menu.
8 OK button (P51)
Determines the item selected from the menu.
4 COMPUTER-1 button (P28, 46)
Selects the image input from the DVI-I/RGB
IN-1 terminal.
9 POINTER button (P50)
Selects the upper, lower, left, or right item in
the menu. The left and right buttons are also
used as volume control buttons.
Pressing this button continuously allows you
to select an input signal (DIGITAL RGB or
ANALOG RGB-1).
10POWER indicator (P27)
Indicates the projector status.
When stays red: The projector can be turned
on.
5 COMPUTER-2 button (P28, 46)
Selects the image input from the RGB IN-2/
COMPONENT IN/RGB OUT terminal.
Pressing this button continuously allows you
to select an input signal (ANALOG RGB-2 or
COMPONENT).
When flashing red: The projector is being
turned off (the lamp is being cooled).
When stays green: The projector is on.
When flashing green: The projector is being
turned on.
6 VIDEO/S button (P46)
Select the image input from the VIDEO IN
terminal or S-VIDEO terminal.
11 WARNING lamp (P79)
Flashes red when a problem has been
detected.
Pressing this button continuously allows you
to select input signals (VIDEO or S-VIDEO).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Terminals on Main Unit
1
2
3
4
5
6
7
9
8
1 S-VIDEO IN terminal (P42)
Receives an S-VIDEO signal from AV
equipment.
5 SERVICE PORT jack
Exclusively used by the service personnel (it
is not used normally).
2 VIDEO IN terminal (P42)
Receives a composite video signal from AV
equipment.
6 USB terminal (P41)
Connected to the computer with a USB cable
when the remote control is used as the
mouse of the computer.
3 DVI-I/RGB IN-1 terminal (P23, 42)
Receives a digital or analog RGB signal from
the computer (DVI terminal).
7 AUDIO IN terminal (P24, 43)
Receives an audio signal (stereo) from the
computer or AV equipment.
4 RGB IN-2/COMPONENT IN/RGB OUT
terminal (P23, 42)
8 Power cord socket (P26)
Receives an analog RGB signal from the
computer or receives a component picture
signal from AV equipment (mini D-sub 15-pin
terminal).
9 Antitheft lock hole
Allows you to connect an antitheft cable.
Also used to output an analog RGB signal by
selecting an option from the menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE PROJECTOR
Determining the Distance to the Screen
The projected image size is determined by the distance between the projector lens and
the screen.
Select the place where the desired image size is obtained according to the figure shown
below.
The image size can be adjusted using the Zoom lever by the lens.
9.1 m (29.9c)
6.0 m (19.7c)
4.5 m (14.8c)
2.4 m (7.9c)
1.2 m (3.9c)
Zoom (max.)
Zoom (min.)
Screen
Optical axis when image is projected
at right angle to the screen.
H1 and H2: H1 is the height of the screen from the intersection of optical axis and screen
surface, and H2 is the height of the intersection when an image is projected at right angle
to the screen.
40"
60"
80"
100"
150"
182"
200"
250"
300"
Screen size (W x H) cm
81 x 61 122 x 91 163 x 122 203 x 152 305 x 229 370 x 277 406 x 305 508 x 381 610 x 457
2.0 m
(6.6
1.2 m
(3.9
55 cm
(1.8
6 cm
(0.2
3.0 m
(9.8
1.8 m
(5.9
82 cm
(2.7
9 cm
(0.3
7.5 m
(24.6
4.5 m
(14.8
206 cm 250 cm
(6.8 (8.2
23 cm 28 cm
(0.8 (0.9
9.1 m
(29.9
5.5 m
(18.0
4.0 m
(13.1
2.4 m
(7.9
110 cm 137 cm
(3.6 (4.5
12 cm 15 cm
(0.4 (0.5
5.0 m
(16.4
3.0 m
(9.8
Projection distance
Zoom (max)
-
-
-
c
)
c
)
c
)
c)
c
)
c)
7.6 m
6.0 m
9.1 m
Projection distance
Zoom (min)
c
)
c
)
c
)
c
)
(24.9
343 cm
(11.3
38 cm
(1.2
c
)
c
)
c
)
(19.7
274 cm
(9.0
30 cm
(1.0
c
)
(29.9
411 cm
(13.5
46 cm
(1.5
c)
H1
H2
c
)
c
)
c
)
c
)
c)
c
)
c
)
c
)
c)
c
)
c
)
c
)
c
)
c)
c
)
c
)
c
)
c)
• Install the projector at the position where the projection distance is about 1.2 m (3.9') to
9.1 m (29.9'). If the installation position is too close, the image is out of focus. If the
installation position is too far, the screen becomes dark.
• The sizes in the above table have been obtained assuming that the aspect ratio is 4:3.
They may vary from the actual sizes depending on the type of the projected image.
For the relationship between the screen size and projection distance, see the table
on page 85.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Determining the Installation Place
Placing in Front of the Screen
Place the projector in front of the screen in such a manner that it is as perpendicular to the
screen as possible.
Screen
Optical axis
A slight error in the projection angle can be corrected using the KEYSTONE
button. (P31)
Placing on a Level Place
Place the projector on a level place.
• Make sure that the installation place is free from any obstacle that may block the
exhaust vent (fan) on the right side of the projector and the air intake vent (air
filter) on the bottom of the projector.
• The screen must not be exposed to direct sunlight or light from lighting
equipment. In a bright room, it is recommended to limit ambient lighting in order
to improve the image quality.
Note
This projector can be hung from the ceiling (Ceiling mounted) with it turned up side down.
When a translucent screen is used, the projector can project an image from behind the
screen (Rear).
When the projector is hung from the ceiling or projector projects an image from behind the
screen, the image must be inverted vertically or horizontally. (P61)
When hanging the projector from the ceiling, optional brackets (part No. RS-CL01)
are required.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projection Angle
The projection angle can be adjusted with the adjustable foot.
Before making this adjustment, connect the computer and AV equipment and project an
image on the screen.
1
Lift the front of the projector and
push the adjusting foot lock.
The adjustable foot extends with
the spring force.
Adjust the projection angle while
pushing the adjustable foot lock,
and then release the lock.
2
With the adjustable foot, the projection angle can be adjusted up to 10 degrees.
Adjust the longitudinal tilt of the projector to +/-20 degrees or less. If the tilt is more
than 20 degrees above and below, a lamp problem can result.
If Keystone Distortion is Large
Extending the adjustable foot too far causes keystone distortion (the projected picture is
trapezoidal). If the distortion is large, adjust the height of the pedestal of the projector.
The keystone distortion can be corrected using the KEYSTONE button. (P31)
Keystone distortion of
image
Adjusting foot
Pedestal
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PROJECTING AN IMAGE
FROM THE COMPUTER
Connecting the Projector to the Computer
Connect the projector to the computer.
Connecting to Video Terminals
• Before connecting cables, turn off both the projector and computer.
• Images may be improperly projected with digital RGB signals in 1280 x 1024 or 1400 x
1050 depending on the type of computer or DVI cable.
• The USB terminal is used to use the remote control just like the computer mouse. Images
cannot be projected simply by connecting the USB cable.
Computer
To monitor output
(mini D-sub 15-pin)
To monitor output
(mini D-sub 15-pin)
To monitor output
(D-sub 15-pin)
To monitor output
(DVI terminal)
Some types of Macintosh
Computer connection
cable
(for mini D-sub 15-pin)*
Computer
Supplied computer
connection
cable
(for DVI)*
connection cable
(for DVI/mini D-sub
15-pin)
MAC adapter
(See the following memo.)
* Use a cable available
optionally or on the
market.
Some computers require adapters. If any con-
nector cannot be fit in the corresponding
socket, refer to the User’s Manual that came
with the computer.
This terminal can be switched to
the monitor output (analog RGB)
terminal by selecting an option
from the menu. (P69)
To ensure projection of high-resolution high-quality images, use of high-performance cables
is recommended.
MAC Adapter (part No. LV-AD02)
For the Macintosh having a D-sub 15-pin (standard) terminal for monitor output, use a MAC adapter.
Set the slide switches (1-6) on the adapter depending on the Macintosh mode as shown below.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio Terminals
Before connecting cables, turn off both the projector and computer.
Connect audio cables as required.
Computer
To AUDIO OUT
Connect with an audio cable
(with stereo mini jacks).
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in
resistor turns down the sound.
• The built-in speaker is monaural.
• The speaker plays the sound from the equipment which the audio cable is
connected to.
Projecting the Image from the Notebook Computer
No image is projected if the external monitor output is turned off on the personal computer
side.
To turn on the external monitor output, press the [LCD] or [VGA] function key while
pressing the Fn key on the keyboard of the personal computer.
The following table shows relationships between personal computer manufacturers and
key combinations.
FUJITSU
SONY
All series
All series
All series
All series
All series
All series
All series
[Fn] + [F10]
[Fn] + [F7]
[Fn] + [F3]
[Fn] + [F5]
[Fn] + [F5]
[Fn] + [F3]
[Fn] + [F3]
HITACHI
All series
PRESARIO
ARMADA
All series
All series
All series
All series
[Fn] + [F7]
[Fn] + [F7]
[Fn] + [F4]
[Fn] + [F8]
[Fn] + [F3]
[Fn] + [F3]
[Fn] + [F2]
COMPAQ
Panasonic
SHARP
TOSHIBA
NEC
DELL
GATEWAY
SOTEC
akia
IBM
For the key combination of the computer series not listed in the above table, refer
to the User’s Manual that came with the computer.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Determining the Output Resolution of the Computer
To make the most of the display performance of this projector, set output signal resolution
of the computer to an optimum value. If the resolution set on the computer is low, the
quality of the projected image is poor.
The procedure for adjusting the resolution is as follows:
Macintosh OSX
Windows XP
1. Open the Apple Menu and select
1. Open the [Start] menu and select
[System Environment Setting].
Control Panel.
2. In the System Environment Setting
window, click the [Displays] icon to
display the Display window.
2. In
the
Control
Panel
window,
double-click the [Display] icon to display
the Display Properties window.
3. Select the [Settings] tab and move the
slider to select “1400 by 1050 pixels”. If
this resolution is not available, select
the highest resolution under 1400 by
1050.
3. Select the [Display] tab and select
“1400 x 1050” from the [Resolution] list.
If this setting is not available, select the
highest resolution under 1400 x 1050.
4. Close the windows.
4. Click the [OK] button.
• Select a screen mode according to the aspect ratio corresponding to the selected
resolution (4:3 for 1400 by 1050 dots). (P33)
• If the display resolution of the computer is set to SXGA (1280 by 1024 dots) or
WXGA (1360 by 768 dots), select [True size] as the screen mode.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Projection
Connecting the Power Cord
Before connecting the power cord, connect the projector to the computer.
Buttons Used Here
Remote control
Top control
Connect the power cord and turn on the projector.
1
Insert the power cord plug in the power cord connection socket.
Be sure to insert the power cord plug as far as it will go.
Insert the power plug.
The [POWER] indicator flashes red. It stays lit when the projector is ready for
power-on operation.
2
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the ground terminal of the power plug to the ground level in order to
use the projector safely. Otherwise, the operating computer may cause
electromagnetic radiation problems and poor reception by TV and radio.
Caution
Unplug the Power Cord When the Projector is Not in Use
The projector constantly consumes about 6W power even when the Power
button is turned off. To ensure safety and power saving, remove the power plug
from the AC outlet when the projector is not used for an extended period of
time.
Turning On the Projector
Once the projector is turned off, it cannot be turned on for about 60 seconds. Wait
until the lamp cooling period ends and the [POWER] indicator lights red.
Make sure that the [POWER] indicator
lights red.
1
Press the [POWER] button.
The [POWER] indicator first blinks green
and then turns lit green.
2
Top control
Remote control
The Opening window is displayed for
about 20 seconds and the along with the
countdown timer.
To project an image immediately, press
the [OK] button.
• Canceling
the
Countdown
Function Performed at the Start
( P61)
• Displaying a Unique Logo on the
Opening Screen (P59, 60)
• If a password entry screen
appears, enter the password.
(P71)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Select
computer.
a
video terminal of the
To input images from the DVI-I/RGB IN-1
terminal, select the [COMPUTER-1]
button. To input images from the RGB IN-
2/COMPONENT/RGB OUT terminal,
select the [COMPUTER-2] button.
Remote control
Top control
4
Select a signal type.
If images are not displayed correctly,
press the button mentioned in step 3
repeatedly to select a desired input type.
Pressing the [COMPUTER-1] button
repeatedly allows you to select DIGITAL
RGB and ANALOG RGB-1 alternately.
Pressing the [COMPUTER-2] button
repeatedly allows you to toggle between
ANALOG RGB-2 and COMPONENT.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Auto PC Adjustment Function
This projector automatically selects a signal type (VGA, SVGA, XGA, SXGA, SXGA+,
etc.) and makes optimum settings for the total number of dots and tracking depending on
the connected computer (auto PC adjustment). (This function cannot be used when digital
RGB is selected.)
When you switched to the computer mode using the [COMPUTER-1] or [COMPUTER-2]
button, press the [AUTO PC] button. The auto PC adjustment becomes active to display
images correctly.
For some computers, the auto PC adjustment does not work. In this case, you
need to make settings (total dots, tracking, horizontal/vertical positions, horizontal/
vertical pixels, etc.) for the input signal.
• The last used signal types are recorded for the [COMPUTER-1] and
[COMPUTER-2] buttons respectively. When the projector is connected to the
same computer, it can be used with the same settings as before simply by
switching to the computer mode.
• For the settings for the input signal, refer to P52 to 57.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Image
Buttons Used Here
Remote control
Top control
Adjusting the Image Size
Move the Zoom lever to adjust the image size.
• If your desired image size is too large or
small to adjust with the Zoom lever, change
the projector installation position.
Adjusting the Focus
Turn the Focus ring to the position where the
projected image looks sharpest.
• If the projection distance is outside the
range from about 1.2 m (3.9') to 9.1 m
(29.9'), focus adjustment may be
impossible. Adjust the projection distance.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Keystone Distortion
If a projected picture has keystone distortion, correct it by using the keystone adjustment
feature.
1
Select Keystone Adjustment.
“Keystone adjustment” appears on the
screen.
Remote control
Top control
2
Correct keystone distortion.
To reduce the length To reduce the length
of the upper edge, of the lower edge,
Keystone distortion must be corrected
while “Keystone adjustment” is displayed
on the screen. (“Keystone adjustment”
disappears 10 seconds later.)
press [^].
press [v].
To reduce the length
of the left edge, press
[<].
To reduce the length
of the right edge,
press [>].
3
Press the [OK] button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
• The result of keystone adjustment is memorized. If the projector installation
position is the same as before, keystone adjustment is not required.
• When Keystone Adjustment is selected, signals are processed digitally. The
image may look different from the original one.
• The aspect ratio of the image may change when keystone is adjusted.
• Keystone can be adjusted vertically and horizontally within the range of +/-20
degrees. The amount of adjustment varies depending on the combination of the
amount of optical zooming, input signal type, and adjustment direction (vertical
or horizontal).
• If the keystone distortion is too large to adjust, move the projector installation
position.
• To cancel the keystone adjustment, press the [KEYSTONE] button again to
display [Keystone Reset]. Then, press the [OK] button.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Screen Mode
You can select one of four screen modes depending on the display resolution of your
computer.
• A screen mode can be selected by selecting “Screen settings” from the menu. (P57)
Full screen
Select this to project an image displayed on the computer screen at
a 4:3 aspect ratio (W:H) (SXGA+ [1400 by 1050 dots] or XGA [1024
by 768 dots]).
The image displayed on the computer screen at a 5:4 (W:H) aspect
ratio is projected with it compressed vertically or horizontally.
Normal
Select this to project an image displayed on the computer screen at
a 5:4 (W:H) aspect ratio (SXGA) or on a wide screen of Macintosh.
Since the image is projected with it fitted to either the width or length
of the computer screen, the top and bottom portions or the leftmost
and rightmost portions of the image are missing.
Wide Screen
Select this to project an image displayed on the computer screen at
a 16:9 (W:H) aspect ratio.
Since the image is projected with it fitted to the width of the
computer screen, the top and bottom portions of the image are
missing.
True size
Select this if you want to project an image in its original size.
A clear image can be obtained because of no image processing.
This mode cannot be selected when the display resolution of the
computer is larger than 1400 by 1050 pixels.
• If the display resolution of the computer is higher than 1400 by 1050 dots, select
a lower resolution before starting projection.
• The upper, lower, left, and/or right portions of a projected image may be missing
depending on the selected display mode.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an Image Mode (Quality)
You can select one of four image modes. You can adjust the image quality (brightness,
contrast, sharpness, gamma, color) as you like.
1
Press the [IMAGE] button.
Remote control
“IMAGE” appears on the screen,
allowing you to select a desired image
mode by pressing the [IMAGE] button
repeatedly.
[Standard]
Select this to project an image with a similar quality to that of the
original image. An image is projected with a high regard for
reproduction of white.
[Presentation] Select this to project an image with a similar quality to that of the
original image. A bright and high-contract image is projected.
[Cinema]
[sRGB]
Select this to project a moving picture. A picture is projected with a
high regard for color tone reproduction.
Select this when you want to project an image from a sRGB-
compatible digital camera.
An image is projected in the display mode conforming to the sRGB
Standard.
• The quality of the image projected in each image mode can be adjusted as
follows. For the adjustment method, refer to "Image Adj. Menu." (P62)
· Brightness
· Contrast
Adjust this when the image is too bright or dark.
Adjust this to decrease or increase contrast of the entire
image.
· Sharpness
Adjust this to soften or sharpen an image.
· Gamma/Dynamic gamma
Adjust this to obtain better balance of contrast.
· Screen color correction/Advanced color adjustment
Adjust this when color tones are different from those of the
original image.
• The results of adjustments made by the user are saved for each of six types of
input signals. Once they are saved, images can be projected with the same
settings.
• An image mode can be selected by selecting “Image adj.” from the menu. (P49,
62)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning Off the Projector
• Turning off the projector again with the lamp in an unstable state shortly after
turning on the projector may shorten the lamp life. Wait at least 5 minutes before
turning off the projector again.
• Remove the AC power cord after the [POWER] indicator lights red after power-
off. Removing the AC power cord immediately can damage the lamp and
circuits.
• Using the projector for more than 24 hours continuously may shorten the life of
the lamp and internal optical components. Turn off the projector at least once in
24 hours and give it a rest for about one hour.
When the power is turned off, cooling of the lamp starts. Therefore, the projector
cannot be turned on again for about 90 seconds.
Press the [POWER] button.
A confirmation message appears on the
screen.
1
Top control
Remote control
To continue projection, wait until the
confirmation message disappears (about
4 seconds) or press a button other than
the [POWER] button.
2
3
Press the [POWER] button again while
message
the
displayed.
confirmation
is
The POWER indicator goes out and
starts flashing red, starting to cool the
lamp.
When the [POWER] indicator lights red in
90 seconds, remove the power cord from
the AC outlet.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Power Management
Function
If the projector receives no signal input within 30 seconds, a countdown timer appears.
The lamp will turn off five minutes later and the projector will enter the power management
mode selected in advance.
You can select one of the following power management modes from the menu. (P70)
Ready mode
Select this mode to start projection immediately.
When the projector enters this mode, the lamp is turned off and its cooling starts. When
the lamp has been cooled down, the [POWER] indicator starts flashing red and green to
enter the ready status. Projection will restart if the input signal is reconnected or any
button on the top control or remote control is pressed.
Shutdown mode
Select this mode to turn off the projector automatically.
When the projector enters this mode, the lamp is turned off and its cooling starts. When
the lamp has been cooled down, the [POWER] indicator stops flashing red and stays lit
and the power is turned off.
When the lamp is being cooled in a power management mode (for 90 seconds),
the projector is inoperative.
The power management function can be disabled (OFF).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
USEFUL FUNCTIONS AVAILABLE
DURING PROJECTION
Let’s take a look at the useful functions
available when you make a presentation
Blacking Out an Image
Temporarily
with a computer connected to the
projector.
[NO SHOW]
Useful when:
Blacking Out an Image Temporarily
[NO SHOW] ...................................... P37
• You finished the presentation.
• You want to divert attendees’
attention from the screen.
Making an Image Larger/Smaller
[D.ZOOM] .......................................... P38
Showing the Elapsed Time
[P-TIMER].......................................... P39
Black out the image temporarily.
Blacking out an Image
Pointing to a Position with a Spotlight
[SPOT]............................................... P39
Remote control
Freezing a Image
[FREEZE]........................................... P40
Muting the Sound/Adjusting the
Volume [MUTE/VOL] ........................ P40
The screen changes to black or blue.
Showing the Image Again
Operating the Mouse Using the
Remote Control ................................ P41
• A unique logo can be captured.
(P59)
• The company logo can be shown
while the image is blacked out.
(P60)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Making an Image Larger/
Smaller
[D.ZOOM]
Moving the Image to the Desired
Position
Useful when:
• Making a small graph larger during
presentation.
If the enlarged image is larger than the
screen, you can move it so that the
desired portion of the image is displayed
inside the screen.
• Moving unnecessary information off
the screen to focus on the current
subject.
Top control
Remote control
Make the projected image larger/smaller.
Making the Image Larger
Remote control
Move the image vertically and horizontally
to display the desired portion on the
screen.
Press this button repeatedly until the
image becomes the desired size.
Making the Image Smaller
Press this button repeatedly until the
image becomes the desired size.
• The zoom ratio is 1x to 12x.
• The enlarged image can also be
frozen.
• Pressing the [D.ZOOM] button
displays the magnification on the
screen.
• Pressing the [OK] button cancels
the digital zoom function.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Showing the Elapsed Time
Indicating a Position with a
Spotlight
[SPOT]
[P-TIMER]
Useful when:
Useful when:
• You point to a portion of an image
• You want to manage the proceedings
of the presentation.
that should
attention.
draw
attendees’
The timer indicating the elapsed time (00:00
to 59:59) is shown in the lower right corner
just like the stopwatch.
Point to a desired portion of the projected
image with a pointer.
Showing the Pointer
Starting the Timer
Remote control
Remote control
A pointer appears at the center of the screen
and the image becomes dark excepting the
pointer.
Pressing this button once shows the timer
and starts the timer.
Multiple types of pointers are supported and
you can select a desired pointer by pressing
the [SPOT] button repeatedly.
Stopping the Timer
Moving the Pointer
Pressing this button once again stops the
timer.
Canceling the P-TIMER function
Move the pointer to a desired position.
To cancel the SPOT function, press the [OK]
button.
The normal screen appears.
When you pressing this button once again,
the timer disappears.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing the Picture
Muting the Sound/
Adjusting the Volume
[FREEZE]
[MUTE]
Useful when:
Useful when:
• You want to mute the sound from the
projector immediately.
• You want to perform a computer
operation which is irrelevant to the
proceedings of the presentation.
• You want to adjust the volume level
of the projector speaker.
• You want to stop a moving image.
Freeze the moving image.
Mute the sound temporarily or adjust the
volume level.
Freezing an Image
Muting the Sound
Remote control
Remote control
“FREEZE” icon is shown on the screen.
“MUTE” icon is shown on the screen.
Canceling the FREEZE function
Canceling the MUTE function
To cancel the FREEZE function, press this
button again.
To cancel the MUTE function, press this
button again.
The frozen image can be expanded
or compressed.
Pressing the [VOL +/-] button also cancels
the MUTE function.
Adjusting the Volume
Top control
Pressing the [+]/[-] button shows a Volume bar
appears on the screen. (If the volume is not
adjusted with the [+]/[-] button in about 4
seconds, the Volume bar disappears.)
The MUTE function can be used from
both the remote control and top control.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving the Cursor
Operating the Mouse Using
the Remote Control
Remote control
Useful when:
• You want to use the supplied remote
control as the wireless mouse of the
personal computer.
You can move the mouse cursor vertically
and horizontally.
Connecting the USB Cable
Make sure that both the computer and
projector are turned off. Connect the
supplied USB cable between the USB
terminal on the computer and the USB
terminal on the projector.
Using the Left Button of the Mouse
Computer
You can perform the click, double-click,
drag operations of the mouse.
Using the Right Button of the Mouse
This function is available on
Windows XP, Windows 2000,
Windows Me, or Mac OS 9.2 and
later.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
PROJECTING AN IMAGE
FROM AV EQUIPMENT
Connecting the Projector to AV Equipment
Connect the projector and AV equipment.
Connecting to Video Terminals
• Before connecting cables, turn off both the projector and computer.
• SCART terminal is not supported.
To digital
video output
To component video output
To analog video output
(S-VIDEO (AV input
terminal)
(VIDEO
terminal)
(DVI terminal)
(D terminal)
(RCA terminal)
terminal)
Component
cable (RCA x 3)
Component
cable (D ter-
minal/RCA x
3)
S terminal
video cable
Video
cable
DVI
cable
AV
cable
Supplied component
cable (RCA/Mini D-sub
15-pin)
*A component cable
available on the
market is required
to connect the
projector to AV
equipment. (See
memo.)
About the Component Cable
The projector cannot be connected to AV equipment using only the supplied component
cable (RCA/Mini D-sub 15-pin). Purchase either of the following cables according to the
type of the terminal on the AV equipment:
• RCA terminal: RCA x 3/RCA x 3
• D-terminal: D-terminal/ RCA x 3
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Audio Terminals
Connect audio cables as required.
Before connecting cables, turn off both the projector and computer.
To AUDIO OUT
Connect with an audio cable
(with stereo mini jacks).
• Use an audio cable without a built-in resistor. Using an audio cable with a built-in
resistor turns down the sound.
• The built-in speaker is monaural.
• The speaker issues the sound from the equipment to which an audio cable is
connected.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Projection
Connect the power cord and turn on the projector.
• Before connecting the power cord, connect the projector to the AV equipment.
• Once the projector is turned off, it cannot be turned on for about 90 seconds.
Wait until the lamp cooling period ends and the [POWER] indicator lights red.
The projection method is basically the same as that used when the projector is
connected to a computer. (P23) Lets take a look at only the topics specific to AV
equipment.
Buttons Used Here
Top control
Remote control
44
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Connect the power cord.
Make sure that the [POWER]
indicator lights red.
Press the [POWER] button.
The [POWER] indicator first blinks
green and then turns lit green.
3
Top control
Remote control
The Opening window is displayed for
about 20 seconds along with the
countdown timer.
• Canceling
the
Countdown
Function Performed at the Start
(61)
• Displaying a Unique Logo on
the Opening Screen (59, 60)
• If a password entry screen
appears, enter the password.
(71)
• To project an image immedi-
ately, press the [OK] button.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Select an AV terminal.
To input images from the DVI-I/RGB IN-
1 terminal, select the [COMPUTER-1]
button.
To input images from the RGB IN-2/
COMPONENT/RGB OUT terminal,
select the [COMPUTER-2] button.
To input image from the S-VIDEO IN
terminal or VIDEO IN terminal, press
the [VIDEO/S] button.
Remote control
Top control
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a signal type.
5
If images are not displayed correctly,
press the button mentioned in step 4
repeatedly to select a desired input
type.
Pressing the [COMPUTER-1] button
repeatedly allows you to select DIGITAL
RGB and ANALOG RGB-1 alternately.
Pressing the [COMPUTER-2] button
repeatedly allows you to toggle between
ANALOG RGB-2 and COMPONENT.
Pressing the [VIDEO/S] button repeat-
edly allows you to toggle between
VIDEO and S-VIDEO.
Remote control
Top control
• This projector cannot project
digital contents copy-protected
by the HDCP technology.
• For the input signal selection
method, refer to 56 and 57.
Play the AV equipment.
The image from the AV equipment
appears.
6
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Image
The image adjustment method is the same as that used when the projector is connected
to a computer. Lets take a look at only the topics specific to AV equipment.
For other image adjustment methods, see P30.
Selecting a Screen Mode
You can select one of three screen modes depending on your AV equipment,
specifications of playback software, etc.
• A screen mode can be selected by selecting “Screen settings” from the menu. (58)
J Normal (VIDEO, S-VIDEO and COM-
PONENT input only)
4:3
Select this if you want to project an image
at a 4:3 aspect ratio (W:H).
16:9
J Wide Screen (VIDEO, S-VIDEO and
COMPONENT input only)
Select this if you want to project an image
at a 16:9 aspect ratio (W:H).
For wide screen sizes, see the
table on 85.
J Auto (COMPONENT input only)
To switch between [Normal] and [Wide
Screen] automatically depending on the
image from the AV equipment, select
[Auto].
• The upper, lower, left, and/or right portions of a projected image may be missing
depending on the selected display mode
• When DIGITAL RGB or ANALOG RGB-1 is selected as the input signal type, the
display mode is the same as that used when the projector is connected to the
computer. (P33)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP FUNCTIONS
USING MENUS
Using Menus
Windows shown on the projector screen to allow you to set up the projector are called
menus.
This projector supports the following three menus:
Display Setting Menu
This menu is used to set input signals of the computer and AV equipment and make
various settings related to display.
Image Adjustment Menu
This menu is used to make various adjustments to the projected image.
System Setting Menu
This menu is used to set various functions of the projector.
First, we will explain the typical procedure for handling menus. Next, we will give a
detailed description of menu items.
Symbols Indicating Item Categories
Menu items are classified into two categories, menu items used to project the image from
the computer and menu items used to project the image from the AV equipment.
Menu item used when projecting
an image from AV equipment.
Menu item used when projecting
an image from the computer.
Component
COMPONENT input
DIGITAL RGB input
D-RGB
A-RGB
VIDEO input/S-VIDEO input
ANALOG RGB-1/-2 input
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Buttons Used Here
Remote control
Top control
1
Press the [MENU] button.
A menu window appears.
• To close the menu window, press the
[MENU] button again.
Top control
Remote control
Select the tab containing the item
you want to set.
2
Select the [Display settings], [Image
Adj.], or [System settings] tab.
• The selected tab contains the items
handled previously. To select another
tab, press the [^] button repeatedly.
Selected item is highlighted in orange.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the item you want to set.
3
4
Make a setting.
Make an adjustment or choice.
Selecting from the Menu
(Example: Screen setup)
Select an item from the menu, make an
adjustment using the slide bar, or make
a setting in a different window accord-
ing to the purpose of setting.
Making an Adjustment Using
the Slide Bar
(Example : Adjustment of Contrast)
Press the [OK] button.
The setting takes effect.
5
Some menu items take effect at the
time they are selected and some take
effect when the [OK] button is
pressed.
Making a Setting in a Different
Window
(Example : Registration of User Logo)
When you finished setting the
selected item, press the [MENU]
button.
6
The menu disappears.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Settings
Menu
Performing the Auto
PC Adjustment
Make various settings related to input signals of
the computer and AV equipment as well as the
settings related to display.
The projector automatically detects the
input signal (ANALOG RGB) from the
connected computer to make the optimum
settings for the total number of dots,
tracking, and so on.
Performing the auto pc
adjustment
[Auto pc adj.]............... P52
[Total dots]................... P53
[Tracking] .................... P53
Adjusting the total
number of dots
Adjusting the tracking
Display settings
Auto PC Adj.
Adjusting the
horizontal position
[Horizontal position] ....... P54
[Vertical position] ........... P54
[Horizontal pixels] .......... P55
Adjusting the vertical
position
Adjusting the number
of horizontal pixels
Adjusting the number
of vertical pixels
[Vertical pixels]............ P55
[Input signal select] ....P56, 57
Selecting an input
signal type
Selecting a Screen mode [Screen settings] ........P57, 58
Selecting a menu
position
[Menu position]............ P58
[Logo capture]............. P59
[Logo position]............. P59
[No signal screen] ....... P60
[No show screen] ........ P60
[Projector on]............... P61
[Image flip H/V] ........... P61
Capturing a logo to be
displayed
Selecting a logo
display position
Perform the auto PC adjust-
ment function.
OK
Displaying a logo
(No signal input)
Displaying a logo
(No Show)
• Most computers can project an
image optimally using an auto PC
function.
• Signal types supported by the
computers that can use the auto
PC function are listed in the table
on page 84.
• If an image cannot be projected
correctly even with the auto PC
function, manually specify the
parameters ([Total dots] to [Verti-
cal pixels]) for the next item [Input
signal settings]. (P53 to P55)
Displaying a logo
(Projector on)
When Ceiling-mounted
or for Rear Projection
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Total
Number of Dots
Adjusting the
Tracking
Adjust the total number of horizontal dots.
Adjust the tracking when the projected
image flickers due to a tracking error.
Display settings
Input signal settings
Total dots
Display settings
Input signal settings
Tracking
Increase the total number of dots.
Reduce the total number of dots.
Increases the set value.
Decreases the set value.
>
<
>
<
This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• The setting is recorded for the
[ANALOG RGB-1] signal and
[ANALOG
separately.
RGB-2]
signal
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the
Horizontal Position
Adjusting the
Vertical Position
Adjust the horizontal position of the
screen when the projected image is
shifted horizontally.
Adjust the vertical position of the screen
when the projected image is shifted
vertically.
Display settings
Display settings
Input signal settings
Vertical position
Input signal settings
Horizontal position
Moves the screen up.
>
<
Moves the screen to the right.
Moves the screen to the left.
>
<
Moves the screen down.
• This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• The setting is recorded for the
[ANALOG RGB-1] signal and
•
The setting is recorded for the
[ANALOG RGB-1] signal and
[ANALOG RGB-2] signal
separately.
[ANALOG
separately.
RGB-2]
signal
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Number
of Horizontal Pixels
Adjusting the Number
of Vertical Pixels
When the horizontal size of the screen is
too large or small, adjust it to the screen
size.
When the vertical size of the screen is too
large or small, adjust it to the screen size.
Display settings
Input signal settings
Horizontal pixels
Display settings
Input signal settings
Vertical pixels
Increase the number of horizontal
pixels.
Decrease the number of horizontal
pixels.
Increase the number of horizontal
pixels.
Decrease the number of horizontal
pixels.
>
<
>
<
• This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• This adjustment is required when
the auto PC adjustment cannot
project images correctly.
• The setting is recorded for the
[ANALOG RGB-1] signal and
• The setting is recorded for the
[ANALOG RGB-1] signal and
[ANALOG
separately.
RGB-2]
signal
[ANALOG
separately.
RGB-2]
signal
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an Input
Signal Type (1)
Selecting an Input
Signal Type (2)
When two or more types of input signals
are found during execution of the auto PC
adjustment function, select a correct input
signal type.
When images from AV equipment is not
projected correctly (irregular color or no
image), you can select an input signal
type manually.
Display settings
Display settings
Input signal select
Input signal select
[1280 x 1024]
[1400 x 1050]
The
automatically set.
If images are not projected
correctly in the Auto mode,
select one of input signal
types shown on the left.
input
signal
is
Auto
•
•
•
NTSC
PAL
Select an input signal type suitable for the
computer from the displayed signal types.
SECAM
NTSC4.43
PAL-M
PAL-N
• Select an input signal type when
the auto PC adjustment function
cannot project images correctly
and two or more signal types are
found.
Confirm the input signal type
according to the User's Manual that
came with the AV equipment
connected.
• For the signal types supported by
this projector, see P84.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an Input
Signal Type (3)
Selecting a Screen
Mode (1)
When images from AV equipment is not
projected correctly, you can select an
input signal type manually.
When the projected image size is larger/
smaller than the screen size.
Display settings
Display settings
Screen settings
Input signal select
The
video
format
is
An image from the computer is
projected fully on the screen.
Auto
automatically set according
to the input signal.
If images are not projected
correctly in the Auto mode,
select one of input signal
types shown on the left.
1080i
1035i
720p
575p
480p
575i
An image is projected in the
maximum size with the
aspect ratio unchanged.
An image is projected at 16:9
aspect ratio with its width
matching to the width of the
screen.
An image is projected in its
original size (no enlargement/
reduction).
480i
Confirm the input signal type
according to the User's Manual that
came with the AV equipment
connected.
• Set the display resolution of the
computer to 1400 x 1050 dots or
lower.
• When Full screen is selected,
circles may become out of round
depending
resolution of the computer.
on
the
display
• The upper, lower, left, and/or right
portions of a projected image may
be missing depending on the
selected display mode.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Screen
Mode (2)
Selecting a
Menu Position
Select a screen mode according to the
size of the image to be projected.
You can select the position of the menu
displayed on the screen.
Display settings
Menu position
Display settings
Screen settings
The screen mode is automat-
ically switched between [Nor-
mal] and [Wide Screen]
depending on the image from
the AV equipment. This item
is displayed when Compo-
nent Input is selected to
allow you to select it.
Using [^], [<], [>], and [v] buttons, move
the menu position.
When the menu position is
determined, press the [OK] button
(the menu will disappear 30 seconds
later if no button is pressed).
An image is projected at a
16:9 (W:H) aspect ratio (wide
screen size).
An image is projected at a
4:3 (W:H) aspect ratio (nor-
mal screen size).
The upper, lower, left, and/or right
portions of a projected image may be
missing depending on the selected
display mode.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Capturing a Logo
to Be Displayed
Selecting a
Logo Display Position
Select a logo display position. A logo can
be displayed at the center or in a corner of
a desired screen.
A user’s unique image (logo) can be dis-
played when the power is turned on, there
is no input signal, or the image is blacked
out temporarily.
Display settings
User screen settings
Logo capture
The image to be captured is
OK
Select a logo display posi-
tion.
Upper L
Upper R
Center
displayed on the screen. Place
the red frame on the capture
range and press [OK]. The
image in the red frame will be
captured.
Lower L
Lower R
Cancel registration of the image.
Cancel
• The image on only one screen can
be captured.
• To display the captured image,
select “Logo capture” on the
“Projector on”, “No signal”, or “NO
SHOW” screen.
• No image can be captured
depending on the resolution and
scan system you selected.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying a Logo
(No signal screen)
Displaying a Logo
(NO SHOW)
A logo can be displayed on the screen
when there is no input signal.
A logo can be displayed on the screen
when the image is blacked out temporarily
by pressing the [NO SHOW] button.
Display settings
User screen settings
No signal screen
Display settings
User screen settings
NO SHOW
Black
No logo is displayed (black
screen).
No logo is displayed (black
screen).
Black
Blue
No logo is displayed (blue-
back).
Blue
No logo is displayed (blue-
back).
The logo captured on the
“Logo capture” screen is dis-
played.
User logo
The logo captured on the
“Logo capture” screen is
displayed.
User logo
”User logo” cannot be selected
when no logo has been captured.
”User logo” cannot be selected
when no logo has been captured.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
When Ceiling-
mounted or for Rear
Projection
Displaying a Logo
(Projector on)
A logo can be displayed from the moment
the projector is turned on to the moment it
is ready for projection.
Make this setting when the projector is
hung from the ceiling or it projects an
image on a transmissive screen.
Display settings
Image flip H/V
Display settings
User screen settings
Projector on
An image is projected normally.
Select this when projecting an image
with the projector hung from the
ceiling. An image is projected with it
inverted vertically.
Canon logo
Skip
The factory-captured Canon
logo is displayed.
Select this when projecting an image
from behind the screen. An image is
projected with it inverted horizontally.
An image is projected imme-
diately after the projector is
turned on.
Select this when projecting an image from
behind the screen with the projector hung
from the ceiling. An image is projected
with it inverted vertically and horizontally.
User logo
The logo captured on the
“Logo capture” screen is dis-
played.
When hanging the projector from the ceiling,
optional brackets are required. Contact your
Canon dealer.
”User logo” cannot be selected
when no logo has been captured.
None (Normal image) Ceiling mounted
Rear
Rear, Ceiling mounted
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adj. Menu
The Image adj. menu is used to make
various adjustments to the image to be
projected.
Selecting an
Image Mode
When the color and brightness of the
displayed image can be adjusted to match
your source.
Selecting an Image Mode
[Image mode]...........................................P62
Adjusting the Brightness [Brightness]...P63
Adjusting the Contrast [Contrast]...........P63
Adjusting the Sharpness [Sharpness]....P64
Making a Gamma Correction [Gamma]...P64
Image adj.
Image mode
Using the Dynamic Gamma Function
[Dynamic Gamma] ..................................P65
Adjusting the Color Level [Color level]...P65
Adjusting the Color Balance
[Color balance]........................................P66
Correcting the Screen Color
[Screen color correction] .......................P66
Select this to project an image with a
Standard
similar quality to that of the original
image. An image is projected with a
high regard for reproduction of white.
Making Advanced Color Adjustment
[Advanced color adjustment] ................P67
Select this to project an image with a
Presentation
similar quality to that of the original
image. A bright and high-contract
image is projected.
Performing Progressive Processing
[Progressive]...........................................P67
Select this to project a movie. A
picture is projected with a high regard
for color tone reproduction.
Cinema
Reducing the Lamp Brightness
[Lamp mode] ...........................................P68
Select this when you want to project
an image from a sRGB-compatible
digital camera.
sRGB
Resetting the Image Settings [Reset] .....P68
An image is projected in the display
mode conforming to the sRGB
Standard.
• The quality (brightness, contrast, etc.)
of the image displayed in each image
mode can be adjusted as desired.
• The results of adjustments made by
the user for each mode are saved for
each of six types of input signals.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the
Brightness
Adjusting the
Contrast
When the image is too bright or dark,
adjust the brightness.
When you want to make the image more
or less vivid, adjust the difference in tone
between the lightest and darkest portions
of the image.
Image adj.
Contrast
Image adj.
Brightness
The image becomes brighter.
The image becomes darker.
The contrast increases. The image
becomes more vivid.
The contrast decreases. The image
becomes less vivid.
>
<
>
<
This setting is saved for the
currently selected input signal and
image mode.
This setting is saved for the
currently selected input signal and
image mode.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the
Sharpness
Making a Gamma
Correction
When you want to make the image
sharper or softer, adjust the sharpness of
the image.
When light or dark portions of an image
are obscure, adjust the image.
Image adj.
Gamma
Image adj.
Sharpness
>
The image becomes sharp.
Dark and obscure portions become
visible.
>
<
<
The image becomes soft.
Light and obscure portions become
visible.
• Sharpness can be adjusted in
four steps in the plus or minus
direction.
This setting is saved for the
currently selected input signal and
image mode.
• This setting is saved for the
currently selected input signal
and image mode.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Dynamic
Gamma Function
Adjusting the
Color Level
The tone representation of light and dark
areas is adjusted automatically.
When an image is too deep or pale in
color, adjust the color level.
Image adj.
Image Adj.
Color level
Dynamic Gamma
On
Off
The dynamic gamma function
is used.
The image becomes deeper in color.
The image becomes paler in color.
>
<
The dynamic gamma function
is not used.
• An image is adjusted automatically
so that the optimum image quality
is attained in real time.
This setting is saved for the currently
selected input signal and image
mode.
• This setting is saved for the
currently selected input signal and
image mode.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Color
Balance
Correcting the
Screen Color
When an image appears too red or green,
adjust the color balance.
Adjust the while balance so that white
areas of the image are displayed correctly.
Image adj.
Image adj.
Screen color correction
Color balance
The reddish image is corrected.
The greenish image is corrected.
When a standard screen is
used, an image is projected
in a color tone similar to that
of natural light.
>
<
• You cannot adjust the color
balance when the video format is
PAL, PAL-M, PAL-N, or SECAM.
• This setting is saved for the
currently selected input signal
and image mode.
When a greenboard (dark
green) is used as a screen,
an image is projected in an
almost natural color tone.
Adjust color tones of red,
green, and blue with the level
meter.
>
The color tone of each
color becomes lighter.
The color tone of each
color becomes darker.
<
This setting is saved for the
currently selected input signal and
image mode.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing Progressive
Processing
Making Advanced
Color Adjustment
When you want to project a high-quality
image, use the progressive processing
function.
Adjust colors using the memorized color
correction function and 6-axis color
adjustment function.
Image adj.
Image adj.
Advanced color adjustment
Progressive
Progressive processing is
performed.
No correction
On
Color adjustment is not performed.
Mem. color correct L
Mem. color correct M
Mem. color correct H
Colors (e.g., blue sky) in our
memory can be adjusted in three
steps so that they can be shown
more vividly.
Progressive processing is
not performed.
Off
6-axis color adjust
A 6-axis color adjustment box (RGB
(red/green/black) and CMY (cyan/
magenta/yellow)) is displayed to allow
you to make fine adjustment of colors.
• This function cannot be used
when the component signal is
1080i, 1035i, 720p, 575p, or 480p.
• This setting is saved for the
currently selected input signal and
image mode.
• Select [Off] when flickers and
horizontal lines are noticeable on
a fast-moving picture.
Select the “Color balance” or “Color level” bar
using the [^] and [v] buttons, and then adjust
colors using the [<] and [>] buttons.
This setting is saved for the
currently selected input signal and
image mode.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Reducing the
Resetting the
Image Settings
Lamp Brightness
When you want to make the image darker
or you feel the fan noisy, reduce the lamp
brightness.
If you want to make all image settings
from the beginning, you can reset the
current settings to the factory defaults.
Image adj.
Image adj.
Reset
Lamp mode
OK
An image is projected at the
normal brightness level.
The lamp brightness is
reduced to make the fan
quieter.
All image settings are reset.
Resetting is canceled.
Normal
Quiet
Cancel
Image settings are saved for each
input signal and image mode. When
[OK] is selected, the settings saved
for the image mode of the currently
selected input signal are reset.
• Selecting [Quiet] allows you to
reduce the power consumption of
the lamp.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings
Menu
Outputting an
Image to a Monitor
You can use the RGB IN-2/COMPONENT
IN/RGB OUT terminal as an analog RGB
terminal.
This menu is used to set various functions
of this projector.
Outputting an Image to a Monitor
[Terminal]........................................ P69
Selecting the Power Management Mode
[Power management mode] .......... P70
System settings
Terminal
Issuing a Beep
[Beep].............................................. P70
Prohibiting Projector Operation
[Key lock]........................................ P71
Registering a Password
[Register password]....................... P71
Setting a Password
[Password settings]...................... P72
Setting up the Remote Control
[Remote control] ............................ P72
The RGB IN-2/COMPO-
NENT IN/RGB OUT terminal
is used as an input terminal.
The RGB IN-2/COMPO-
NENT IN/RGB OUT terminal
is used as an output terminal.
Selecting a Display Language
[Language]...................................... P73
Resetting to Factory Defaults
[Factory defaults]........................... P73
When [COMPUTER-2] is selected,
a monitor output setting cannot be
done even if [ANALOG RGB] is
selected for the input signal.
Press the [COMPUTER-1] button
before making a monitor output
setting.
Resetting the Lamp Counter
[Lamp counter]............................... P74
An image can be output to a monitor
IN-2/
OUT
through
COMPONENT
the
RGB
IN/RGB
terminal only when [Computer-1]
and [ANALOG RGB] are selected
for the input signal.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Power
Management Mode
Issuing a Beep
When the projector is not used, the
mercury lamp is turned off or the power is
turned off automatically for power saving.
A beep can be sounded when the power
is turned on/off or a button on the top
control or remote control is pressed.
System settings
System settings
Beep
Power management mode
The power management
mode is not used.
A beep is issued.
Off
On
Off
A beep is not issued.
The projector enters the
power management mode. It
restarts projection when a
signal is input or an operation
button is pressed.
Standby
A beep is not issued when the
sound has been muted by pressing
the [MUTE] button.
The projector enters the exit
mode, being turned off
automatically.
Exit
For details on Power Management
Mode, refer to P36.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Prohibiting
Projector Operation
Registering a
Password
You can prohibit use of the buttons on the
top control and remote control to prevent
buttons from being pressed by mistake.
Register a password that you need to
enter when turning on the projector.
System settings
Key lock
System settings
Register password
OK
The key lock function is not
used.
Press the [OK] button and
the password entry screen
will appear.
Off
Use of the top control is
prohibited.
Main unit
Remote control
Use of the remote control is
prohibited.
Enter a 4-digit password using [^], [>], [v],
and [<] buttons.
Pressing the [^] button enters 1, pressing
the [>] button enters 2, pressing the [v]
button enters 3, and pressing the [<]
button enters 4.
• The key lock function becomes
effective from the moment the
[OK] button is pressed after
selecting [Main unit] or [Remote
control]. Be sure to press the [OK]
button on the top control or
remote control which is not
locked.
Enter digits starting with the leftmost digit.
When you finish entering four digits, the
password will be registered automatically.
When you want to cancel registering
the password, press the [MENU]
• To unlock buttons forcibly, remove
the power plug from the AC outlet
after completion of projection, and
then insert the power plug with
the [OK] button pressed.
button
password.
without
entering
the
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting a
Password
Setting up the
Remote Control
Set a password in the projector. Once the
password is set, you will need to enter the
password each time you turn on the
projector.
When you use two projectors at the same
time, change the channel settings to
prevent the two remote controls from
interfering with each other.
System settings
Remote control
System settings
Password settings
The password function is not
used.
The password function is
used.
Select the channel on the
projector you use, and then
press the [OK] button.
Ch1
Ch2
Off
On
Selecting a Channel for the Remote Control
While pressing the [OK] button on the remote
control, press the [LIGHT] button for 3
seconds.
• Once a password is set in the
projector, a password entry screen
appears at power-on. Enter a 4-
digit password using [^], [v], [<],
and [>] buttons. If the password is
valid, projection starts. If you enter
a wrong password three times, the
projector will be turned off.
• To cancel the password, remove
the power plug from the AC outlet
after completion of projection, and
then insert the power plug in the
AC outlet with the [MENU] button
pressed.
Pressing the two buttons allows you to switch
between CH1 (the button flashes once) and
CH2 (the button flashes twice).
• When setting a channel, be sure to
set the same channel for either
control (remote control or top
control). Set a different channel for
the other pair.
• When performing menu operation
using the remote control, changing
the channel by pressing the [OK]
button will prevent you for using
the remote control.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a
Display Language
Resetting to the
Factory Defaults
You can reset menu item settings. The
system settings will be restored to the
factory defaults.
You can select a language to be used in
the menu from 13 different languages.
System settings
Factory defaults
System settings
Language
Select a display language.
All menu item settings of the
projector are reset to factory
defaults.
OK
English
German
French
Resetting is canceled.
Cancel
Italian
Spanish
• The
[Lamp
counter]
and
Portuguese
Swedish
[Language] settings will not be
reset even after resetting to
factory defaults.
Russian
• For the factory defaults, refer to
P86.
Dutch
Chinese (Simplified)
Chinese (Traditional)
Korean
Japanese
Select a language and press the
[OK] button and all words used in the
menu will be displayed in the
selected language.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the
Lamp Counter
When you have changed the lamp, reset
the lamp counter that indicates the lamp
replacement timing.
• When the time of use is less than 1,000
hours
• When the time of use is 1,000 to 1,400
hours
The lamp counter is reset.
Resetting of the lamp
counter is canceled.
• When the time of use is 1,400 hours or
longer
Do not reset the lamp counter
except when you have replaced the
lamp. If reset, the lamp counter
cannot indicate the correct timing of
lamp replacement.
For the lamp replacement method,
refer to P77.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning the Projector
Clean the projector frequently to prevent dust from accumulating on the surface.
A dirty lens can affect the quality of the projected image.
• The main unit is very hot immediately after turning off the projector. Wait until
the projector cools down sufficiently before cleaning the projector. You may get
burned or injured.
Caution
• Before cleaning, be sure to remove the power plug from the AC outlet.
Otherwise, electric shock or fire may result.
Cleaning the Projector Body
Softly wipe the projector body with a soft cloth.
If the projecter is heavily soiled, use a small amount of detergent diluted with water, damp
a cloth with this solution, squeeze the cloth hard, wipe the projector body with this cloth,
and finish with a dry cloth.
• Using volatile cleaning liquid or benzine may damage the projector body
surface. When using a chemical dust cloth, read the instructions thoroughly.
• To clean the lens, use a commonly available air blower or lens cleaning paper.
Caution
The lens surface is easily damaged, so do not use a hard cloth or tissues.
When Not Used for an Extended Period of Time
Be sure to attach the lens cap on the lens and store in the supplied carrying bag.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Replacing the Air Filter
An air filter is installed in the air intake vent on the bottom of the main body to protect the
internal lens and mirror from dust. Should the air filter become clogged with dust, it will
block the air flow into the projector and causing an internal heat buildup which may cause
a problem.
• The main unit is very hot immediately after turning off the projector. Wait until
the projector cools down sufficiently before cleaning the air filter. You may get
burned or injured.
Caution
• Before cleaning or replacing the air filter, be sure to remove the power plug
from the AC outlet. Electric shock or fire may result.
• Do not insert any object into the projector through the air filter opening. You
may suffer electric shock or injury due to the high-voltage parts or rotating
parts.
Cleaning the Air Filter
Turn the projector upside down, remove the cover by pushing the latch, remove the air
filter, and clean it with a vacuum cleaner.
When cleaning dust off the side exhaust vent and the bottom air intake vent, bring the
vacuum cleaner nozzle close to them directly.
• Clean the air filter frequently.
• After cleaning the air filter, install it following the removal steps in reverse.
Procedure for Replacing the Air Filter
Turn off the projector, remove the power
1
plug from the AC outlet, and leave the
projector stand for at least 1 hour.
Cover
Remove the filter cover by pushing the
latch.
2
Air filter
Remove the air filter.
3
Attach a new air filter under the filter cover.
4
Install the filter cover in place.
5
• Attach the lens cap when replacing the air filter.
• Handle the air filter carefully. If damaged, the air filter will not work properly.
• Replace the air filter whenever you replace the lamp.
• An air filter can be ordered from your Canon dealer.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Lamp
When the time of use of the lamp is 1400 hours or longer, the following message (two
types) is displayed for 10 seconds each time the projector is turned on.
• When the time of use is 1,400 to 1,500 hours
• When the time of use is 1,500 hours or longer
• This message will not appear again, if you select [No] in response to the
message "Do you want to display this message again?".
• Check the time of use of the lamp in [Lamp counter] from the System settings
menu. (P74)
• When replacing the lamp, turn off the projector, wait until the cooling fan
stops, remove the power plug from the AC outlet, and let the projector stand
for at least 1 hour. You may get burned because the main unit is very hot
immediately after the projector is turned off.
Caution
• When replacing the lamp do not touch the inner glass surface. The
projector’s performance may degrade.
About the Replacement Lamp
This projector uses the following lamp.
Lamp type No. : RS-LP01
Be sure to use the lamp of the specified type.
A lamp can be ordered from your dealer.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure for Replacing the Lamp
1
Turn off the projector and disconnect
the power plug from the AC outlet.
Allow the projector to cool for a least
1 hour.
Lamp cover
Screw
Detach the lamp cover by loosening
a screw with a flathead screwdriver.
2
3
Loosen two screws, turn up the
handle, and remove the lamp.
Handle
Lamp
Insert a new lamp as far as it will go
4
and secure it with two screws.
* After installation, be sure to turn
down the handle.
Screws
5
Install the lamp cover and tighten the
screw.
Lamp cover
6
Turn on the projector.
7
Bring up the menu and select
[System settings] -> [Lamp counter].
(P74)
Select [Reset] -> [OK] to reset the
lamp counter.
8
78
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Understanding the Warning Lamp
Flash Patterns
When an internal problem occurs, the WARNING lamp on the Control Panel flashes red.
When dealing with the problem, turn off the projector, wait until the cooling fan
stops, remove the power plug from the AC outlet.
Flash Pattern
Meaning
Countermeasure
One flash
Abnormal
The temperature inside the projector is too high for
temperature some reason or the outside air temperature is higher
than the specified one.
If the problem is inside the projector, check whether
the projector is installed and operated normally, turn
off the projector to cool its inside, and retry projection.
If the same warning occurs again, the projector may
be defective. Contact your dealer.
Two flashes
Faulty lamp
The lamp has burnt out. Replace the lamp with a new
one. If the same warning occurs again, the lamp drive
circuit may be defective. Contact your dealer.
Three flashes
Faulty lamp
cover
The lamp cover is open. Check whether the lamp
cover is installed properly. If it is installed properly, the
lamp cover detection switch may be defective. Contact
your dealer.
Four flashes
Five flashes
Faulty
cooling fan
The cooling fan or another component may be
defective. Contact your dealer.
Faulty power The voltage of part of the power supply is abnormally
supply
high or any other problem has occurred in the power
supply. Contact your dealer.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptoms and Solutions
No power
Cause
Countermeasure
The power cord is not connected prop- Check whether the power cord is connected properly.
erly.
(P26)
The power cord has just been con- After connecting the power plug, you cannot turn on the
nected. projector before the [POWER] lights red. (P27)
You attempted to turn on the projector The projector cannot be turned on for about 90 seconds
immediately after turning it off.
after it is turned off.
Wait for at least 90 seconds and press the [POWER] but-
ton again. (P35)
No image
Cause
Countermeasure
Any connection cable is connected Check whether the projector is properly connected to the
improperly. computer and AV equipment. (P23, 42)
20 seconds have not passed since the When the projector is turned on, the Opening window is
projector was turned on.
displayed for about 20 seconds. To project an image
immediately, press the [OK] button on the remote control
or top control. (P27)
No image is sent from the AV equip- Check that an image is played back on the connected dig-
ment. ital camera, video camcorder, DVD, etc. (P47)
Connection to the video terminal or Check that connection to the video terminal is correct.
selection of a signal type is incorrect. Also check that selection of a signal type is correct. (P28,
47)
The [NO SHOW] function is selected. Press the [NO SHOW] button on the remote control. (P37)
No image is sent due to the problem Turn on the projector and computer in this order again.
occurred on the computer side.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
No sound
Cause
Countermeasure
The audio cable is not connected Check whether the audio cable is connected properly.
properly.
(P24, 43)
The [MUTE] function is selected.
Press the [MUTE] button on the remote control. (P40)
The volume level is adjusted to the Adjust the [VOL+] button on the remote control or top con-
minimum. trol to adjust the volume level. (P40)
An audio cable with a built-in resistor Use an audio cable without a built-in resistor.
is used.
Out of focus
Cause
Countermeasure
Adjust the focus. (P30)
Remove the lens cap. (P92)
The image is out of focus.
The lens cap is not removed.
The distance to the screen is too Check whether the distance to the screen is proper.
If the distance is shorter than about 3.9' (1.2 m), the image
cannot be brought to a focus. (P20, 85)
short.
The projector is not placed straight in Check whether an image is obliquely projected to the
front of the screen.
screen. A slight error in the projection angle can be cor-
rected through keystone adjustment. (P21, 31)
The projector has been moved to a When the projector is moved from a low-temperature
place where the difference in tempera- place to a high-temperature place, dews may form on the
ture is large.
lens. Dews will evaporate a while later and the projector
will be able to project a normal image.
Top/bottom or left/right reversed
Cause
Countermeasure
An image is projected with its top and The ceiling mounted/rear projection setting is incorrect.
bottom or left and right reversed.
Check the "Image flip H/V" setting in the Display settings
menu. (P61)
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Cannot project image from notebook computer
Cause
Countermeasure
The connection cable is not connected Check whether the connection cable is properly connected
properly.
to the video terminal of the computer. (P23)
The video signal type is incorrect.
Check whether the selected signal type is correct. (P28,
84)
The external monitor output setting on Turn on the external monitor output on the notebook com-
the notebook computer is incorrect.
puter.
To turn on the external monitor output, press the [LCD] or
[VGA] function key while pressing the [Fn] key on the key-
board of the notebook computer. (P24)
The combination of keys used to perform this operation
varies among computer manufacturers. Refer to the
User's Manual that came with your computer.
The displayed image is not the same Check whether the dual screen (multi-display) mode is
as that displayed on the notebook selected on the notebook computer.
computer.
When the dual screen mode is selected, change it to the
simultaneous display mode (output setting) on the note-
book personal computer.
The output setting method varies among computer manu-
facturers. Refer to the User's Manual that came with your
computer.
Power turns off
Cause
Countermeasure
The air intake or exhaust vent is Check whether the air intake or exhaust vent is blocked.
blocked.
If the air intake or exhaust vent is blocked, the temperature
inside the projector rises and the power is automatically
turned off to protect the main body of the projector. Wait
until the internal temperature lowers, and turn on the pro-
jector with the intake and exhaust vents unblocked. (P21,
76)
The fir filter is dirty.
Check whether the bottom air filter is clogged with dust.
If the air filter is clogged, clean or replace the air filter.
(P76)
The lamp has burnt out (or it is defec- Check whether the lamp has burnt out.
If the lamp has burnt out, replace it.
tive).
The lamp may be defective if it has not burnt out. Check
the lamp by replacing it with a spare lamp if you have it.
(P12, 77)
Check whether the operating temperature is 5 to 35oC.
(P13)
The operating
improper.
temperature
is
Others
The projector may be out of order. Contact Canon dealer
immediately. (Back cover)
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Cannot operate the remote control
Cause
Countermeasure
Batteries are not installed properly or Check whether batteries are installed properly. If batteries
they have run out.
are installed properly, replace them with one batteries.
(P17)
You are operating the remote control Check whether you are operating the remote control within
outside the remote control operating the remote control operating range.
range.
Also check whether there is any obstacle between the
infrared remote receiver of the projector and the remote
control. (P16)
The operating environment of the Check whether the infrared remote receiver of the projec-
remote control is bad.
tor is exposed to direct sunlight or strong light of lighting
apparatus. (P16)
The remote control code does not Check whether the remote control code has been
match the projector setting.
changed.
You can confirm the "Remote control" setting in the Sys-
tem settings menu. (P72)
"Key lock" is turned on to disable Check whether "Key lock" is turned on to disable remote
remote control operation.
control operation.
In the System settings menu, set "Key lock" to "Off." (P71)
Cannot operate the wireless mouse
Cause
Countermeasure
The USB cable is not connected prop- Check whether the USB cable is properly connected
erly.
between the projector and computer. (P41)
A mouse driver is not installed.
Check whether the mouse can be used on the computer
side. If it cannot be used, install a mouse driver in the com-
puter.
The mouse is not recognized due to a Turn on the projector and computer in this order again.
computer problem.
This symbol on the nameplate means the product is Listed by
Underwriters Laboratories Inc. It is designed and manufactured to
meet rigid U.L. safety standards against risk of fire, casualty and
electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
83
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Computer Signal Types
This projector supports signals of the following types.
If your computer or AV equipment is compatible with any one of these signal types, the auto
PC function of the projector judges the type of the input signal to project an image correctly.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Relationship between Screen Size
and Projection Distance
Zoomed projection distance
Screen size at 4:3
aspect ratio
W x D (cm)
Screen size at 16:9
aspect ratio
W x D (cm)
H1
H2
Max.
Min.
2.0 m
c
(6.6 )
2.5 m
1.2 m
c
(3.9 )
1.5 m
c
(4.9 )
1.8 m
c
(5.9 )
2.1 m
c
(6.9 )
2.4 m
c
(7.9 )
2.7 m
c
(8.9 )
3.0 m
55 cm
c
(1.8 )
69 cm
c
(2.3 )
82 cm
c
(2.7 )
96 cm
c
(3.1 )
110 cm
c
(3.6 )
123 cm
c
(4.0 )
137 cm
c
(4.5 )
151 cm
c
(5.0 )
165 cm
c
(5.4 )
178 cm
c
(5.8 )
192 cm
c
(6.3 )
206 cm
c
(6.8 )
219 cm
c
(7.2 )
233 cm
c
(7.6 )
241 cm
c
(7.9 )
247 cm
c
(8.1 )
250 cm
c
(8.2 )
261 cm
c
(8.6 )
274 cm
c
(9.0 )
288 cm
c
(9.4 )
302 cm
c
(9.9 )
315 cm
c
(10.3 )
329 cm
c
(10.8 )
343 cm
c
(11.3 )
357 cm
c)
(11.7
370 cm
c
(12.1 )
384 cm
c
(12.6 )
398 cm
6 cm
c
(0.2 )
8 cm
c
(0.26 )
9 cm
c
(0.3 )
11 cm
s
40 81 x 61
s
37 81 x 46
s
50 102 x 76
s
46 102 x 57
c
3.0 m
(8.2
)
s
60 122 x 91
s
55 122 x 69
c
(9.8 )
3.5 m
s
70 142 x 107
s
64 142 x 80
c
(11.5
4.0 m
c
(0.36 )
12 cm
)
s
80 163 x 122
s
74 163 x 91
c
(13.1 )
4.5 m
c
(0.4 )
14 cm
(0.46c)
15 cm
c
(0.49 )
17 cm
c
(0.56 )
18 cm
c
(0.59 )
20 cm
c
(0.66 )
21 cm
c
(0.69 )
23 cm
c
(0.75 )
24 cm
c
(0.79 )
26 cm
c
(0.85 )
27 cm
c
(0.86 )
27 cm
c
(0.86 )
28 cm
c
(0.9 )
29 cm
s
90 183 x 137
s
83 183 x 103
c
(14.8
5.0 m
)
s
100 203 x 152
s
91 203 x 114
c
c
(16.4 )
5.5 m
(9.8 )
3.3 m
s
110 224 x 168
s
101 224 x 126
c
(10.8 )
3.6 m
c
(18.0
6.0 m
)
s
120 244 x 183
s
110 244 x 137
c
c
(19.7 )
6.5 m
c
(21.3 )
7.0 m
c
(23.0 )
7.5 m
c
(24.6 )
8.0 m
(11.8 )
3.9 m
s
130 264 x 198
s
119 264 x 149
c
(12.8 )
4.2 m
c
(13.8 )
4.5 m
c
(14.8 )
4.8 m
c
(15.7 )
5.1 m
c
(16.7 )
5.3 m
c
(17.4 )
5.4 m
c
(17.7 )
5.5 m
c
(18.0 )
5.7 m
c
(18.7 )
6.0 m
c
(19.7 )
6.3 m
c
(20.7 )
6.6 m
c
(21.7 )
7.0 m
c
(23.0 )
7.3 m
c
(24.0 )
7.6 m
c
(24.9 )
7.9 m
c
(25.9 )
8.2 m
s
140 284 x 213
s
128 284 x 160
s
150 305 x 229
s
138 305 x 171
s
160 325 x 244
s
147 325 x 183
c
(26.2
8.5 m
)
s
170 345 x 259
s
156 345 x 194
c
(27.9 )
8.8 m
s
176 358 x 268
s
162 358 x 201
c
(28.9
9.0 m
)
s
180 366 x 274
s
165 366 x 206
c
(29.5 )
9.1 m
c
(29.9 )
s
182 370 x 277
s
167 370 x 208
s
190 386 x 290
-
-
-
-
-
-
-
-
-
-
-
-
s
174 386 x 217
c
0.95 )
(
30 cm
s
200 406 x 305
s
184 406 x 229
c
0.98 )
(
32 cm
s
210 427 x 320
s
193 427 x 240
c
1.05 )
(
34 cm
s
220 447 x 335
s
202 447 x 251
c
1.12 )
(
35 cm
s
230 467 x 351
s
211 467 x 263
c
1.15 )
(
37 cm
s
240 488 x 366
s
220 488 x 274
c
1.21 )
(
38 cm
s
250 508 x 381
s
233 508 x 286
c
1.25 )
(
40 cm
s
260 528 x 396
s
239 528 x 297
c
1.31 )
41 cm
(
s
270 549 x 411
s
248 549 x 309
c
(26.9 )
8.5 m
c
(27.9 )
8.8 m
c
(28.9 )
9.1 m
c
(29.9 )
c
1.35 )
(
43 cm
s
280 569 x 427
s
257 569 x 320
c
1.41 )
(
44 cm
s
290 589 x 442
s
266 589 x 331
c
(13.1 )
411 cm
c
(13.5 )
c
1.44 )
(
46 cm
s
300 610 x 457
s
276 610 x 343
c
1.51 )
(
85
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/S-VIDEO
Screen settings
Menu Configuration
Factory Defaults
Normal
Wide Screen
Input signal select
Auto
Switching between
NTSC
Computer and AV Equipment
Select the input terminal of the equipment
from which an image is to be input, and
select an input signal type using a button
on the remote control or top control.
PAL
SECAM
NTSC4. 43
PAL-M
PAL-N
Input terminal
Button
Input signal
DIGITAL RGB
ANALOG RGB-1
ANALOG RGB-2
COMPONENT
VIDEO
COMPONENT
DVI-RGB IN-1
COMPUTER-1
Screen settings
Auto
Normal
RGB IN-2/COMPONENT IN/RGB OUT
COMPUTER-2
VIDEO/S
Wide Screen
Input signal select
Auto
1080i
1035i
720p
575p
480p
575i
VIDEO IN
S-VIDEO IN
S-VIDEO
Items in Menu
Items displayed in the menu vary
depending on the selected input signal.
480i
Display settings
Menu position
/
/
/
ANALOG RGB-1/ANALOG RGB-2
Logo capture
Logo position
User screen settings
OK/Cancel
Auto PC adj.
Upper L
Upper R
Center
Lower L
Lower R
Input signal settings
Total dots
/
/
/
/
/
/
Tracking
Horizontal position
Vertical position
Horizontal pixels
Vertical pixels
Return
Black
No signal screen
NO SHOW
Blue
User logo
Black
Input signal select
Screen settings
640 x 480
Blue
User logo
800 x 600
:
1400 x 1050
Canon logo
Skip
User logo
Projector on
Return
Full screen
Normal
Wide Screen
True size
Image flip H/V
None
Ceiling mounted
Rear
Rear,Ceiling mounted
DIGITAL RGB
Screen settings
Full screen
Normal
Wide Screen
True size
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Image adj.
System settings
Image mode
Standard
Presentation
Cinema
Terminal
INPUT
MONITOR OUT
sRGB
Power management mode
Off
Brightness
Contrast
/
/
/
/
Standby
Exit
Beep
On
Off
Sharpness
Gamma
Key lock
Off
Dynamic Gamma
On
Off
Main unit
Remote control
VIDEO/S VIDEO/COMPONENT
Color level
Register password
Password settings
Entering the password
/
/
On
Off
Color balance
Remote control
Language
CH1
CH2
Screen color
correction
Normal
Greenboard
Adjust
Red
/
/
/
English
Green
Blue
Return
German
French
Italian
Advanced color
adjustment
No correction
Spanish
Mem.color correct L
Mem.color correct M
Mem.color correct H
6-axis color adjust
Portuguese
Swedish
Russian
Color balance
Color level
/
/
Dutch
Chinese(Simplified)
Chinese(Traditional)
Korean
VIDEO/S VIDEO/COMPONENT
Progressive
On
Off
Japanese
Lamp counter
Back
Reset
OK/Cancel
OK/Cancel
Lamp mode
Reset
Normal
Quiet
Factory defaults
OK/Cancel
: Factory defaults (settings after resetting)
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Analog RGB
A signal system used to send information about R (red), G (green), and B (blue) with analog
values. It is a typical system for connecting a color monitor to a computer. Connect the
analog RGB output terminal of the computer and the DVI-I/RGB IN-1 terminal or RBG-2/
COMPONENT IN/RGB OUT terminal of this projector with a monitor cable. When the RGB
IN-1 terminal is used, select “ANALOG RGB-1” by pressing the [COMPUTER-1] button.
When the RGB IN-2 terminal is used, select “ANALOG RGB-2” by pressing the
[COMPUTER-2] button.
Digital RGB
A signal system used to send information about individual display dots with digital values.
This system is free from deterioration of image quality because of no analog conversion.
Connect the DVI output terminal of the computer and the DVI-I/RGB IN-1 terminal of this
projector with a connection cable and select “DIGITAL RGB” by pressing the [COMPUTER-
1] button.
Video
An output terminal widely used for AV equipment. It is also called a composite output
terminal (pin terminal or RCA terminal). For more details, refer to “Composite”.
S-video
A signal system (YC separation signal) used to send a brightness signal (Y) and color signal
(C) separately. Connect the S-video terminal of AV equipment and the S-VIDEO IN terminal
of this projector with an S-video cable and select “S-VIDEO” by pressing the [VIDEO/S]
button.
Component
A signal system used to send a color signal (C) with it divided into a B-Y color difference
signal and an R-Y color difference signal. This system can project a better-quality image as
compared with the composite signal system. Connect the video terminal of AV equipment
and the RGB-2/COMPONENT IN/RGB OUT terminal with a component cable and select
“COMPONENT” by pressing the [COMPUTER-2] button.
Composite
A video signal system used to send a brightness signal (Y) and a color signal (C) together.
Connect the composite output terminal (RCA) of AV equipment and the VIDEO IN terminal of
this projector with a video cable and select “VIDEO” by pressing the [VIDEO/S] button.
sRGB
An international standard of color representation (color space) which is applied to digital
cameras, displays and others. If you select sRGB, the projector can project the best-quality
image conforming to the sRGB Standard.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Progressive
An image display system used to display the entire screen per scan. When an interlace
signal (video signal) that displays one screen by two scans (one for odd lines and one for
even lines) is input, progressive processing is required. When the progressive function is
turned off, one screen is displayed using image signals per interlace signal, deteriorating the
vertical resolution of the image. When the progressive function is turned on, one screen is
displayed using image signals per two interlace signals, improving the vertical resolution of
the image. Turn off the progressive function when flickering and horizontal lines are
noticeable on a fast-moving picture.
Resolution
The number of dots (horizontal dots x vertical dots) that can be displayed on a computer is
called “resolution of display”. Resolution indicates the size of the display area (amount of
information).
UXGA 1600 x 1200 (4:3)
Number of dots
Resolution
Horizontal
640
Vertical
480
SXGA + 1400 x 1050 (4:3)
SXGA 1280 x 1024 (5:4)
VGA
SVGA
XGA
800
600
XGA 1024 x 768 (4:3)
1024
1280
1400
1600
768
SXGA
SXGA+
UXGA
1024
1050
1200
Number of pixels in each resolution
Selecting SXGA+ (1400 dots x 1050 dots) as the display resolution of the computer allows
this projector to project high-resolution images. If your computer does not have the SXGA+
option, select the maximum resolution among the selectable options.
Gamma Correction
A tone adjustment system used during projection of image data. The gamma correction
function works effectively when portions of an image are obscure because they are too light
or dark.
This projector supports manual gamma correction, automatic gamma correction, and
dynamic gamma correction.
DVI-I
A digital video signal connection interface. This interface allows digital data to be sent and
received without conversion to analog data, assuring high image quality with no signal
degradation. The DVI-I (integrated) connector can be used to send and receive analog RGB
video signals in addition to digital signals.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
Ω
90
Download from Www.Somanuals.com. All Manuals Search And Download.
External View
RGB IN-2/COMPONENT IN/RGB OUT
(Computer Input, Component Input, and Monitor Input/Output
Terminals)
This terminal is used as a computer input or monitor output terminal. When used as a
monitor output terminal, the computer (analog) signal input to the DVI-I terminal is output.
Use a D-sub computer cable.
Mini S-sub 15-pin
1 R
9
+5 V power
2 G
10 Ground (Vertical sync.)
11 Monitor ID0
3 B
4 Monitor ID2
12 DDC data
5 Ground (Horizontal sync.) 13 Horizontal sync.
6 Ground (R)
7 Ground (G)
8 Ground (B)
14 Vertical sync.
15 DDC clock
The specification for the computer input terminal and that for the monitor output
terminal are the same.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Lens Cap
Install the lens cap in the following manner:
Pass the supplied string through the lens cap
string hole on the bottom of the projector, and
then pass the other end of the string in the hole on
the lens cap.
Optional Parts
• Lamp
Part No.: RS-LP01
• Ceiling Attachment
• Ceiling Pipe (360 mm / 14.2″)
• Ceiling Pipe (550 mm / 21.7″)
• Ceiling Pipe (760 mm / 29.9″)
• Ceiling Plate
Part No.: RS-CL01
Part No.: RS-CL03*
Part No.: RS-CL04*
Part No.: RS-CL05*
Part No.: RS-CL02**
Part No.: LV-AD02
Part No.: LV-CA29
• Mac Adapter
• DVI Cable
* This part is used to hang the projector from a high ceiling.
** This part is used to join the ceiling pipe and the ceiling attachment.
For more information, refer to the instruction manual that comes with the ceiling
attachment RS-CL01.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A., INC.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
CANON CANADA, INC.
6390 Dixie Road Mississauga, Ontario L5T 1P7 Canada
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A.
CANON MEXICANA, S. de R.L. de C.V.
Boulevard Manuel Avila Camacho, No. 138 PB, Pisos 15, 16 y 17Col. Lomas de
Chapultepec, CP 11000, Mexico D.F., Mexico
CANON EUROPA N.V.
P.O.Box 2262, 1180 EG Amstelveen, The Netherlands
CANON COMMUNICATION & IMAGE FRANCE S.A.
102, Avenue du General de Gaulle, 92250 La Garenne Colombes, France
CANON (UK) LTD.
Woodhatch, Reigate, Surrey RH2 8BF, United Kingdom
CANON DEUTSCHLAND GmbH
Europark Fichtenhain A 10, 47807 Krefeld, Germany
CANON ITALIA S.p.A.
Palazzo L, Strada 6, 20089 Milanofiori-Rozzano (MI), Italy
CANON (Schweiz) A.G.
Industriestrasse 12, 8305 Dietlikon, Switzerland
CANON BELGIUM N.V./S.A
Bessenveldstraat 7, 1831 Diegem, Belgium
CANON GmbH
Zetschegasse 11, A-1232 Wien, Austria
CANON ESPANA S.A.
C/Joaquin Costa 41, 28002 Madrid, Spain
CANON SVENSKA AB
Stensätravägen 13, S-127 88 Skarholmen 2, Sweden
CANON NORGE A/S
Hallagerbakken 110, P. O. Box 2-33, Holmlia 1201 Oslo 12, Norway
CANON OY
Huopalahdentie 24, P.O. Box 1, FIN-00351 Helsinki, Finland
CANON HONGKONG CO., LTD.
9/F, The Hong Kong Club Building, 3A Chater Road, Central, Hong Kong
CANON SINGPORE PTE. LTD.
79 Anson Road #09-01/06, Singapore 079906
CANON AUSTRALIA PTY. LTD.
1 Thomas Holt Drive, North Ryde, Sydney, N.S.W.2113, Australia
CANON NEW ZEALAND LTD.
Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand
CANON DENMARK A/S
Knud Hoejgaards Vej, DK-2860 Soeborg, Denmark
YT1-1349-000
1004N0.5
© CANON INC. 2004
PRINTED IN JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
|
MTD Yard Vacuum 245 675 000 User Manual
Nespresso Espresso Maker 3035 User Manual
Newcon Optik Hunting Equipment DN 463 User Manual
Nilfisk ALTO Vacuum Cleaner 963 21 ED XC User Manual
NorthStar Navigation Fish Finder NorthStar 491 User Manual
Oregon Scientific Clock RRA320PN User Manual
OWI Portable Speaker Satellite Speaker User Manual
Panasonic Answering Machine KX TDA600 User Manual
ParaBody Home Gym 810102 User Manual
Patton electronic Network Card 3054 User Manual