NEC Flat Panel Television LCD195WXM User Manual

MultiSync LCD195WXM  
User’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For the Customer to use in U.S.A. or Canada  
Canadian Department of Communications Compliance Statement  
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.  
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1.  
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950-1.  
FCC Information  
1.  
Use the attached specified cables with the MultiSync LCD195WXM colour monitor so as not to interfere with radio and  
television reception.  
(1)  
The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,  
and meet the following condition.  
Power supply cord  
Length  
Non shield type, 3-conductor  
2.0 m  
Plug shape  
U.S.A  
(2)  
Please use the supplied shielded video signal cable and audio cable. Use of other cables and adapters may  
cause interference with radio and television reception.  
2.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult your dealer or an experienced radio/TV technician for help.  
If necessary, the user should contact the dealer or an experienced radio/television technician for additional  
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:  
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government  
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.  
Declaration of Conformity  
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not  
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
U.S. Responsible Party: NEC Display Solutions of America, Inc.  
Address:  
500 Park Blvd, Suite 1100  
Itasca, Illinois 60143  
(630) 467-3000  
Tel. No.:  
Type of Product:  
Display Monitor  
Equipment Classification: Class B Peripheral  
Model: MultiSync LCD195WXM (L195H0)  
We hereby declare that the equipment specified above conforms  
to the technical standards as specified in the FCC Rules.  
English-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Your new NEC MultiSync LCD monitor box* should contain the following:  
MultiSync LCD monitor with tilt base  
Audio Cable  
Power Cord  
Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male)  
Video Signal Cable (DVI-D to DVI-D)  
User’s Manual  
CD-ROM  
Cable management cover  
Cable management  
cover  
CD-ROM  
User’s Manual  
Audio Cable  
Power Cord  
15-pin mini D-SUB  
male to 15-pin mini  
D-SUB male  
DVI-D to DVI-D  
MultiSync LCD monitor  
*
Remember to save your original box and packing material to transport or ship the monitor.  
Quick Start  
To pull the stand, follow these instructions:  
1. Place monitor face down on a non-abrasive surface (Figure 1).  
2. Pull the stand holding the monitor with the other hand until the stand clicks (Figure 2).  
NOTE:  
Handle with care when pulling the stand.  
Figure 1  
Figure 2  
NOTE:  
Reverse this procedure if you need to re-pack the monitor.  
To attach the MultiSync LCD monitor to your system, follow these instructions:  
1. Turn off the power to your computer.  
2. For the PC or MAC with DVI digital output: Connect the DVI-D signal cable to the connector of the display card in your  
system (Figure A.1). Tighten all screws.  
For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your  
system (Figure A.2). Tighten all screws.  
For the Mac: Connect the MultiSync Macintosh cable adapter (not included) to the computer. Attach the 15-pin mini  
D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure A.3). Tighten all screws.  
NOTE:  
Some Macintosh systems do not require a Macintosh cable adapter.  
Macintosh  
Cable Adapter  
(not included)  
Figure A.1  
Figure A.2  
English-3  
Figure A.3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. To attach the Cable management cover:  
Insert the tabs of the Cable management cover into the holes of Stand neck  
and slide the Cable management cover downward into place (Figure A.4).  
NOTE:  
Please confirm that the tabs are completely secure.  
4. Connect all cables to the appropriate connector on the back of the monitor  
(Figure B.1). Connect the Headphone (not included) to the appropriate  
connector at the rear side of the monitor (Figure C.1).  
Stand  
Base  
5. Connect one end of the power cord to the monitor and the other end to the  
power outlet. Place the Video Signal Cable, Audio cable and power cord to  
the Cable management cover (Figure B.1).  
Cable management cover  
Figure A.4  
NOTE:  
Adjust position of cable that place under the Cable management cover  
to avoid damage for cable or monitor.  
NOTE:  
Please refer to Caution section of this manual for proper selection of power cord.  
6. Turn on the monitor with the front power button and the computer (Figure C.1).  
Power Cable  
Input (VGA)  
Input (Audio)  
Input (DVI)  
Power Button  
Headphone  
Cable management cover  
Connect to Computer  
audio output  
Figure B.1  
Figure C.1  
7. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.  
For further adjustments, use the following OSD controls:  
• Auto Adjust Contrast  
• Auto Adjust  
Refer to the Controls section of this User’s Manual for a full description of these OSD controls.  
NOTE:  
If you have any problem, please refer to the Troubleshooting section of this User’s Manual.  
Raise and Lower Monitor Screen  
The monitor may be raised or lowered. To raise or lower  
screen, place hands on each side of the monitor and lift or  
lower to the desired height (Figure RL.1).  
NOTE:  
Handle with care when raising or lowering the  
monitor screen.  
Figure RL.1  
Tilt and Swivel  
Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired  
(Figure TS.1).  
NOTE:  
Handle with care when tilting and swivelling the monitor screen.  
Figure TS.1  
English-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remove Monitor Stand for Mounting  
To prepare the monitor for alternative mounting purposes:  
1. Disconnect all cables.  
2. Place monitor face down on a non-abrasive surface (Figure R.1).  
3. Remove the 4 screws connecting the monitor to the stand and remove the stand as indicated (Figure R.2).  
The monitor is now ready for mounting in an alternative manner.  
4. Connect the AC cord and signal cables to the back of the monitor (Figure R.3).  
5. Reverse this process to re-attach stand.  
NOTE:  
NOTE:  
Use only VESA-compatible alternative mounting method.  
Handle with care when removing monitor stand.  
Non-abrasive surface  
Figure R.1  
Figure R.2  
Figure R.3  
Connecting a Flexible Arm  
This LCD monitor is designed for use with a flexible arm.  
Please use the attached screws (4pcs) as shown in the picture when installing. To meet the safety requirements, the monitor  
must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor.  
The LCD monitor shall only be used with an approved arm (e.g. GS mark).  
Replace screws  
Thickness of Bracket  
(Arm) 2.0 ~ 3.2mm  
Tighten all screws  
100mm  
100mm  
Specifications  
4-SCREWS (M4)  
MAX depth: 8.5mm  
If use other screw,  
check depth of hole.  
Weight of LCD assembly: 4.6 kg (MAX)  
English-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls  
OSD (On-Screen-Display) control buttons on the front of the monitor  
function as follows:  
1. Basic function at pressing each key  
SELECT  
Showing OSD.  
Go to Adjustment stage.  
1<->2 / RESET  
+
Button  
At No OSD  
showing  
Shortcut to Bright adjust  
window.  
Shortcut to Volume adjust  
window.  
Input signal select.  
At OSD showing  
(Icon selection stage)  
Cursor goes to left.  
Cursor goes to right.  
At OSD showing Go to Icon selection stage.  
(Adjustment stage)  
Adjust value decrease or  
Adjust value increase or  
Reset operation.  
Mute off/on switch on Volume  
adjustment window.  
Cursor for adjust goes to left. Cursor for adjust goes to  
right.  
2. OSD structure  
Main Menu (Icon Select, Analog Input)  
Main Menu (Adjust)  
Press  
“SELECT”  
key  
Press  
“SELECT”  
key  
Adjust by using  
“–” or “+”  
Press “SELECT” key  
Example Tool:  
Press “SELECT” key  
Press  
“SELECT” key  
Press  
“–” or “+”  
Press  
“–” or “+”  
Press  
“SELECT” key  
Sub Menu (Icon Select)  
Adjust by using  
“–” or “+”  
Sub Menu (Adjust)  
English-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AUDIO  
Control the sound volume of speakers and headphone.  
To mute the speaker sound, press the 1<->2/RESET key.  
BRIGHTNESS  
Adjusts the overall image and background screen brightness.  
CONTRAST  
Adjusts the image brightness in relation to the background.  
AUTO CONTRAST (Analog Input only)  
Adjusts the image displayed for non-standard video inputs.  
AUTO ADJUST (Analog Input only)  
Automatically adjusts the Image Position, the H. Size and Fine setting.  
LEFT/RIGHT (Analog Input only)  
Controls Horizontal Image Position within the display area of the LCD.  
DOWN/UP (Analog Input only)  
Controls Vertical Image Position within the display area of the LCD.  
H. SIZE (Analog Input only)  
Adjusts the horizontal size by increasing or decreasing this setting.  
FINE (Analog Input only)  
Improves focus, clarity and image stability by increasing or decreasing this setting.  
COLOUR CONTROL SYSTEMS  
Five colour presets (9300/7500/sRGB/USER/NATIVE) select the desired colour setting.  
The sRGB and NATIVE, colour presets are standard and cannot be changed.  
COLOUR RED  
Increase or decreases Red. The change will appear on screen.  
COLOUR GREEN  
Increase or decreases Green. The change will appear on screen.  
COLOUR BLUE  
Increase or decreases Blue. The change will appear on screen.  
TOOL  
Selecting TOOL allows you to get into the sub menu.  
FACTORY PRESET  
Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings. The RESET button  
will need to be held down for several seconds to tage effect. Individual settings can be reset by highlighting the  
control to be reset and pressing the RESET button.  
EXIT  
Selecting EXIT allows you exit OSD menu/ sub menu.  
LANGUAGE  
OSD control menus are available in nine languages.  
OSD TURN OFF  
The OSD control menu will stay on as long as it is in use. In the OSD Turn OFF submenu, you can select how  
long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are  
10 - 120 seconds by 5 seconds step.  
English-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSD LOCK OUT  
This control completely locks out access to all OSD control functions without Brightness and Contrast. When  
attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD are  
locked out. To activate the OSD Lock Out function, press “1<->2/ RESET”, then “+” key and hold down  
simultaneously. To de-activate the OSD Lock Out, press “1<->2/ RESET”, then “+” key and hold down  
simultaneously.  
RESOLUTION NOTIFIER  
If ON is selected, a message will appear on the screen after 30 seconds, notifying you that the resolution is not at  
optimal resolution.  
DDC/CI  
Turns ON or OFF the two way communication and control of the monitor.  
MONITOR INFO  
Indicates the model and serial numbers of your monitor.  
INPUT RESOLUTION (Analog Input Only)  
Sets of the resolution of input signal to one of the following: 1280 x 768 and 1360 x 768.  
1280 x 768: Determines the resolution to 1280 x 768.  
1360 x 768: Determines the resolution to 1360 x 768.  
OSD Warning  
OSD Warning menus disappear with SELECT button.  
NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or  
when there is a change of input signal or video is inactive, the No Signal window will appear.  
RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power is  
turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the  
Resolution Notifier window will open. This function can be disabled in the TOOL menu.  
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After  
the power is turned on or there is a change of input signal or the video signal doesn’t have proper timing,  
the Out Of Range menu will appear.  
English-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Recommended use  
Safety Precautions and Maintenance  
FOR OPTIMUM PERFORMANCE, PLEASE NOTE  
THE FOLLOWING WHEN SETTING UP AND  
USING THE MULTISYNC LCD COLOUR MONITOR:  
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose  
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.  
Do not spill any liquids into the cabinet or use your monitor near water.  
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful  
or fatal or may cause electric shock, fire or equipment failure.  
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.  
Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to  
the monitor.  
When operating the LCD monitor with its AC 125-240V power supply, use a power supply aord that matches the power  
supply voltage of the AC power outlet being used. The power supply cord you use must have been approved by and  
comply with the safety standards of your country. (Type H05VV-F should be used in Europe).  
In U.K, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor.  
If a power cord is not supplied with this monitor, please contact your supplier.  
Do not place any objects onto the monitor and do not use the monitor outdoors.  
The inside of the fluorescent tube located within the LCD monitor contains mercury. Please follow the bylaws or rules of  
your municipality to dispose of the tube properly.  
Do not bend power cord.  
Do not use monitor in high temperature, humid, dusty, or oily areas.  
Do not cover vent on monitor.  
Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following  
conditions:  
When the power supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into the monitor.  
If the monitor has been exposed to rain or water.  
If the monitor has been dropped or the cabinet damaged.  
If the monitor does not operate normally by following operating instructions.  
If monitor is broken, do not come in contact with the liquid crystal and handle with care.  
Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated  
openings or place the monitor near a radiator or other heat sources. Do not put anything on top of  
monitor.  
CAUTION  
The power cable connector is the primary means of detaching the system from the power supply. The  
monitor should be installed close to a power outlet, which is easily accessible.  
Handle with care when transporting. Save packaging for transporting.  
Image Persistence: Please be aware that LCD Technology may experience a phenomenon known as Image Persistence.  
Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of  
time should be avoided.  
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an  
image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to  
erase the image.  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a  
moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.  
English-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN  
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE  
FOLLOWING WHEN YOU POSITION THE MONITOR:  
For optimum performance, allow 20 minutes for warm-up.  
Adjust the monitor height so that the top of the screen is at or slightly below eye level.  
Your eyes should look slightly downward when viewing the middle of the screen.  
Position your monitor no closer than 40 cm and no further away than 70 cm from your  
eyes. The optimal distance is 50 cm.  
Rest your eyes periodically by focusing on an object at least 6 m away. Blink often.  
Position the monitor at a 90° angle to windows and other light sources to minimize glare  
and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.  
If reflected light makes it hard for you to see your screen, use an antiglare filter.  
Adjust the monitor’s brightness and contrast controls to enhance readability.  
Use a document holder placed close to the screen.  
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize  
turning your head while you are typing.  
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).  
Get regular eye checkups.  
Ergonomics  
To realize the maximum ergonomics benefits, we recommend the following:  
Use the preset Size and Position controls with standard signals.  
Use the preset Colour Setting.  
Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.  
Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue to insufficient  
contrast.  
Cleaning the LCD Panel  
When the liquid crystal panel is stained with dust or dirt, please wipe with soft cloth gently.  
Please do not rub the LCD panel with hard material.  
Please do not apply pressure to the LCD surface.  
Please do not use OA cleaner it will cause deterioration or discolor on the LCD surface.  
Cleaning the Cabinet  
Unplug the power supply  
Gently wipe the cabinet with a soft cloth  
To clean the cabinet, dampen the cloth with a neutral detergent and water, wipe the cabinet and follow with a dry cloth.  
NOTE:  
Many plastics are used on the surface of the cabinet. DO NOT clean with benzene, thinner, alkaline detergent,  
alcoholic system detergent, glass cleaner, wax, polish cleaner, soap powder, or insecticide. Do not touch rubber or  
vinyl to the cabinet for a long time. These types of fluids and fabrics can cause the paint to deteriorate, crack or  
peel.  
English-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Monitor Specifications  
MultiSync LCD195WXM Monitor  
Diagonal: 48 cm/19 inches  
Viewable Image Size: 48 cm/19 inches  
Native Resolution (Pixel Count): 1440 x 900  
Notes  
LCD Module  
Active matrix; thin film transistor (TFT)  
liquid crystal display (LCD); 0.284 mm dot  
pitch; 300 cd/m2 white luminance,  
1000:1 contrast ratio, typical;  
response time: 5 ms.  
Input Signal  
PC INPUT: Video: ANALOG 0.7 Vp-p/75 Ohms  
Digital Input: DVI-D  
Sync: Separate sync.TTL Level (Positive/Negative)  
Horizontal sync. Positive/Negative  
Vertical sync. Positive/Negative  
AUDIO INPUT: STEREO Mini Jack  
500mV rms Input Impedance 14 Kohm  
Head Phone Output  
STEREO Mini Jack  
Headphone Impedance 32 Ohm  
Display Colours  
Analog input: 16,7 M  
Depends on display card used.  
Synchronization Range  
Horizontal: 31.5 kHz to 81.1 kHz  
Vertical: 56 Hz to 76 Hz  
Automatically  
Automatically  
Viewing Angle  
Left/Right: -80°/+80° (CR>10), -89°/+89° (CR>5)  
Up/Down: -80°/+80° (CR>10), -89°/+89° (CR>5)  
Resolutions Supported Landscape: 720 x 400*1 : VGA  
Some systems may not  
support all modes listed.  
640 x 480*1 @ 60 Hz to 75 Hz  
800 x 600*1 @ 56 Hz to 75 Hz  
832 x 624*1 @ 75 Hz  
1024 x 768*1 @ 60 Hz to 76 Hz  
1280 x 768*1 @ 60 Hz  
1152 x 864*1 @ 60 Hz to 75 Hz  
1152 x 870*1 @ 75 Hz  
1360 x 768*1 @ 60 Hz  
Recommended resolution is 60 Hz for  
1440 x 900 @ 60 Hz to 75 Hz..................... optimal display performance.  
Horizontal: 408.2 mm  
Vertical: 255.2 mm  
Practical Audio Output: 1.0 W + 1.0 W  
100 - 240 V ~ 50/60 Hz  
42 W  
Active Display Area  
Speakers  
Power Supply  
Power Consumption  
Dimensions  
Landscape: 440.0 mm (W) x 340.0 - 390.0 mm (H) x 240.0 mm (D) (with stand)  
440.0 mm (W) x 302.0 mm (H) x 65.5 mm (D) (without stand)  
Weight  
with stand: 5.8 kg  
without stand: 4.6 kg  
Environmental Considerations  
Operating Temperature: 5 °C to 35 °C  
Humidity: 30% to 80%  
Altitude: 0 to 3,048 m  
Storage Temperature: -10 °C to +60 °C  
Humidity: 10% to 85%  
Altitude: 0 to 12,192 m  
*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is  
normal and necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on  
the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.  
NOTE:  
Technical specifications are subject to change without notice.  
English-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight  
limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another.  
Colour Control System: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor  
to a variety of standards.  
No-touch Auto Adjust: No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup.  
ErgoDesign Features: Enhance human ergonomics to improve the working environment, protect the health of the user and  
save money. Examples include OSD controls for quick and easy image adjustments, tilt base for preferred angle of vision,  
small footprint and compliance with MPRII and TCO guidelines for lower emissions.  
Plug and Play: The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the  
monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically  
optimizing display performance.  
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a  
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions  
and lowering the air conditioning costs of the workplace.  
Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the  
resolution required.  
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.  
VESA Standard Mounting Interface: Allows users to connect their MultiSync monitor to any VESA standard third party  
mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant device.  
English-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
No picture  
The signal cable should be completely connected to the display card/computer.  
The display card should be completely seated in its slot.  
Check front power Switch and computer power switch should be in the ON position.  
Check to make sure that a supported mode has been selected on the display card or system being used. (Please  
consult display card or system manual to change graphics mode.)  
Check the monitor and your display card with respect to compatibility and recommended settings.  
Check the signal cable connector for bent or pushed-in pins.  
Check the signal input.  
Power Button does not respond  
Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.  
Image persistence  
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image  
Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT  
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of  
time should be avoided.  
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an  
image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to  
erase the image.  
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a  
moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.  
Image is unstable, unfocused or swimming is apparent  
Signal cable should be completely attached to the computer.  
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine total. When the  
display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.  
Check the monitor and your display card with respect to compatibility and recommended signal timings.  
If your text is garbled, change the video mode to non-interlace and use 60 Hz refresh rate.  
LED on monitor is not lit (no green or amber colour can be seen)  
Power Switch should be in the ON position and power cord should be connected.  
Display image is not sized properly  
Use the OSD Image Adjust controls to increase or decrease the H.SIZE.  
Check to make sure that a supported mode has been selected on the display card or system being used.  
(Please consult display card or system manual to change graphics mode.)  
No Video  
If no video is present on the screen, turn the Power button off and on again.  
Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).  
No Sound  
Check to see if speaker cable is properly connected.  
Check to see if mute is activated.  
Check to see if volume in OSD is set at minimum.  
English-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TCO’03  
Congratulations!  
The display you have just purchased carries the TCO’03 Displays  
label. This means that your display is designed, manufactured and  
tested according to some of the strictest quality and environmental  
requirements in the world. This makes for a high performance  
product, designed with the user in focus that also minimizes the  
impact on our natural environment.  
Some of the features of the TCO’03 Display requirements:  
Ergonomics  
• Good visual ergonomics and image quality in order to improve the working environment for  
the user and to reduce sight and strain problems. Important parameters are luminance,  
contrast, resolution, reflectance, colour rendition and image stability.  
Energy  
• Energy-saving mode after a certain time – beneficial both for the user and the environment  
• Electrical safety  
Emissions  
• Electromagnetic fields  
• Noise emissions  
Ecology  
• The product must be prepared for recycling and the manufacturer must have a certified  
environmental management system such as EMAS or ISO 14 001  
• Restrictions on:  
- chlorinated and brominated flame retardants and polymers  
- heavy metals such as cadmium, mercury and lead.  
The requirements included in this label have been developed by TCO Development in co-  
operation with scientists, experts, users as well as manufacturers all over the world. Since the  
end of the 1980s TCO has been involved in influencing the development of IT equipment in a  
more user-friendly direction. Our labelling system started with displays in 1992 and is now  
requested by users and IT-manufacturers all over the world.  
For more information, please visit  
English-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manufacturer’s Recycling and Energy Information  
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s  
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-  
friendly products, and always strive to help define and comply with the latest independent standards from agencies such as  
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).  
Disposing of your old NEC product  
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of  
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely  
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling  
procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end  
of its life.  
All required information concerning the disposal of the product and country-specific information on recycling facilities can be  
found on our following websites:  
Energy Saving  
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)  
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.  
Mode  
Power consumption  
Approx. 42W  
LED colour  
Green  
Normal Operation  
Energy Saving Mode  
Off Mode  
Less than 2W  
Orange  
Unlit  
Less than 1W  
WEEE Mark (European Directive 2002/96/EC)  
Within the European Union  
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic  
products carrying the mark (left) must be disposed of separately from normal household waste. This includes  
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your  
NEC display products, please follow the guidance of your local authority, or ask the shop where you  
purchased the product, or if applicable, follow any agreements made between yourself and NEC.  
The mark on electrical and electronic products only applies to the current European Union Member States.  
Outside the European Union  
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local  
authority so as to comply with the correct disposal method.  
English-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Dishwasher G 4281 User Manual
Miele Vacuum Cleaner S 6000 User Manual
Moxa Technologies Pet Fence AWK 1200 AP User Manual
MTD Outdoor Cart 45 01763 User Manual
NEC Computer Monitor P232W User Manual
NETGEAR Network Router WNDR4300 User Manual
Nilfisk ALTO Pressure Washer Pressure Washers User Manual
Nintendo Video Game Controller MAA RVL A WR USZ C0 User Manual
NordicTrack Treadmill NTTL11990 User Manual
Omnitron Systems Technology Network Card 8250 0 User Manual