MUSTANG SURVIVAL
�
INFLATABLE VEST
WITH LIFTTM
Owner’s Manual
MD0450 22 Inflatable Vest with LIFTTM
Hydrostatic Inflation Model - Manual with Automatic Backup
SecureZIPTM US Patent No. 6,832,415 and Patents Pending
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Page 1 Introduction
1 Why are PFDs Required Safety Equipment?
2 What is an Inflatable PFD?
3 Instructions for Use
3 Component Inspection Instructions
4 Readiness Checklist
5 Donning Instructions
6 Inflation
8 In-water Adjustments
9 Special Considerations for Automatic Devices
10 Deflation
10 Usage Below Freezing
11 Re-arming Your PFD
15 Auto/Manual Conversion Cap (MA7219) Instructions
15 Conversion Instructions
17 Repacking
23 Is Your PFD in Good and Serviceable Condition?
24 Care and Maintenance Instructions
26 Cleaning and Storing
26 How and Why to Test Your PFD
27 How Do You Test Your PFD Using the Automatic Inflator?
27 How Do You Test Your PFD Using the Manual Inflator?
28 How Do You Test Your PFD Using the Oral Inflator?
29 Wear Your PFD
30 Hypothermia
31 Each of These Devices is Intended to Help You Save Your Life
32 Safety Accessories
32 Do Not Attach PFDs to Your Boat
32 Airline Operator Policy on Carriage of Inflatable PFDs
Inflatable Vest with LIFTTM Owner’s Manual
i
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The MD0450 22 requires user involvement to ensure a level of safety
equal to other inflatable PFDs. Knowledgeable users increase their safety
significantly by wearing and using these PFDs as prescribed in this
owner’s manual.
General - This Inflatable PFD will turn most wearers from a face
down to a face up position and provide support suitable for offshore
conditions. See page 11 for re-arming instructions.
This Inflatable PFD was designed to be more comfortable and less
restrictive to wear than inherently buoyant PFDs. When worn, used and
serviced according to this owner’s manual, this PFD can greatly increase
your chances of survival in the water. Not recommended for non-
swimmers or weak swimmers.
To be considered serviceable, this PFD shall not exhibit deterioration
that could diminish its performance such as broken or deformed
hardware, detached webbing, rotted structural components, air leaks,
or nonfunctional oral inflation tube. Unless worn inflated, this PFD must
also be properly armed with a full CO2 cylinder, inflation system status
indicator, and a manual inflation beaded handle accessible outside the
user’s right front panel cover (Fig. 1). The chest buckle, on the Inflatable
Vest with LIFTTM, must be fastened after inflation.
WHY ARE PFDS REQUIRED SAFETY EQUIPMENT?
Drownings are the leading cause of fatalities involving recreational and
commercial vessels. A PFD provides flotation to help keep your head
above water, help you to stay face up in the water, and increase your
chances for survival and rescue. Most adults only need an extra 7 to 12
kg (3.2 to 5.5 pounds) of flotation to keep their heads above water. The
proper size PFD will properly support the weight of the wearer.
Since this Inflatable PFD does not have inherent buoyancy, it provides
flotation only when inflated. Familiarize yourself with the use of this
1
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Inflatable PFD so you know what to do in an emergency.
WHAT IS AN INFLATABLE PFD?
Congratulations on the purchase of your Inflatable Vest with Patent
Pending LIFTTM [Life-saving Inflatable Flotation Technology]. LIFTTM is
different from all other inflatable PFD’s. In general, inflatable PFD’s are
designed to suspend a user’s head above water to prevent drowning.
The Inflatable Vest with LIFTTM provides freeboard that far exceeds the
minimal 3” generally provided. LIFTTM elevates you to an upright safe
position and delivers up to 9” of freeboard, the highest ever seen in
a PFD, keeping your mouth high above the water line to minimize the
risk of mouth immersions. Not only is LIFTTM one of the world’s best
performing PFD’s in wave conditions, but it’s comfortable too. Light and
ergonomically designed – you can’t even tell you’re wearing it until you
need it.
While traditional PFDs are inherently buoyant, inflatable PFDs like the
Inflatable Vest with LIFTTM rely entirely upon inflation for buoyancy.
Uninflated, the Inflatable Vest with LIFTTM is comfortable and can be
inflated at any time with a 38-gram CO2 gas cylinder. The Inflatable Vest
with LIFTTM is designed to meet the demands of a full protection PFD
offering maximum mobility with minimum bulk. The Inflatable Vest with
LIFTTM can be inflated either automatically during immersion, manually
by pulling a beaded handle, or by mouth. It is imperative that you
familiarize yourself with the procedures outlined in INSTRUCTIONS FOR
USE (p. 3).
Inflatable Vest with LIFTTM Owner’s Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR USE
This manual supplies instructional, maintenance and safety information
for model MD0450 22 unless specified otherwise. The model number is
listed on the label.
FIGURE 1
MD0450 Unpacked
Oral Inflator
Cover Panel
Window
Chest Strap
Hydrostatic
Velcro Tab
Chest
Inflator
FOLD #1
FOLD #1
Buckle
FOLD #3
FOLD #3
FOLD #2
FOLD #2
Waist Belt
Front Buckle
Beaded
Handle
Right Lobe
Left Lobe
FIGURE 2
Hydrostatic Inflator Cap
Water Inlet Valve
Black Locking Ring
Yellow Inflator Cap
Cap/Locking Ring
Tabs
Single
Point
Status
Indicator
Lanyard
Inflator
Body
Expiry
Date
Beaded
Handle
Component Inspection Instructions
1) Examine the single point indicator through the window panel. Ensure
the single point indicator is green. If the single point indicator is red,
the mechanism has been fired or is incorrectly fitted (Fig. 2). See
3
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
RE-ARMING YOUR PFD (p. 11).
NOTE: The single point indicator must be green before
proceeding.
2) Open the cover at wearer’s right-hand side of the chest and lay the
device flat.
3) Ensure the oral-inflation dust cap is in the stowed position (Fig. 22).
4) Ensure the single point indicator is green and the beaded handle is
attached to it’s Velcro tab; secure the zippers on the Inflatable Vest
with LIFTTM (see Repacking, p. 17).
5) Ensure the date on the inflator is not five years or older (Fig. 2). If it
is, replace the inflator (see Re-arming Your PFD, p. 11).
Readiness Checklist
Check your Inflatable Vest with LIFTTM and ensure all of the checkpoints
listed below are true before each use.
■ Single point indicator is green.
■ Ensure the current date is not past the date on the inflator. If it is,
replace the inflator (see Re-arming Your PFD, p. 11).
■ All zippers, Velcro™ and waist buckle are securely fastened.
■ Inflatable Vest with LIFTTM is not twisted.
■ Oral-inflation dust cap is in the stowed position (Fig. 22).
■ Ensure the beaded handle is placed through the opening and is
attached to the Velcro tab on the outside of the vest (Fig. 35).
■ No rips, tears or holes; all seams are securely sewn; and the fabric,
straps and hardware are still strong.
Your Inflatable Vest with LIFTTM is ready for use if all boxes are checked.
NOTE: Contact your Mustang Dealer if you have any concerns
about the readiness of your Inflatable Vest with LIFTTM.
Inflatable Vest with LIFTTM Owner’s Manual
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Donning Instructions
It is important that the PFD is properly adjusted to fit the person wearing
it. An incorrect fit or improper fastening of attachments could reduce its
effectiveness.
1) Put the Inflatable Vest with LIFTTM on just like a jacket (Fig. 3). If
the Inflatable Vest with LIFTTM is already inflated prior to donning,
it may be excessively tight while donning. If so, expel some air by
depressing the oral tube valve, don the Inflatable Vest with LIFTTM,
and refill Inflatable Vest with LIFTTM by mouth using the oral tube.
2) Fasten the front waist belt buckle (Fig 3). Adjust the waist belt to a
secure fit using the front adjuster on the belt.
WARNING: Do not wear the Inflatable Vest with LIFTTM under
other clothing or harness systems as the inflation could be
restricted and you could be injured.
FIGURE 3
NOTE: Heavy objects in the pockets may cause the PFD to sink
if dropped overboard when not inflated.
5
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Fasten the middle buckle (Fig. 4). Adjust the middle belt to a secure
fit using the front adjuster on the belt.
FIGURE 4
IMPORTANT: Ensure the
chest buckle is fastened,
when inflated (Fig. 4).
4) Feed the loose end of the waist belt into the belt opening in the
storage pocket (Fig. 5).
FIGURE 5
Inflation
It is recommended that the following procedures be followed to inflate
your Inflatable Vest with LIFTTM.
Manual Inflation
1) Activate the inflation system by grasping the beaded handle and jerk
Inflatable Vest with LIFTTM Owner’s Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
firmly downward. The PFD should fully inflate within 5 seconds (Fig.
6).
NOTE: Deflation may occur if the CO2 cylinder is removed
while the Inflatable Vest with LIFTTM is inflated.
FIGURE 6
2) Fasten the chest straps (Fig. 7) and adjust to a snug fit.
Important: Ensure the chest buckle is fastened, when inflated.
FIGURE 7
Fastened
Chest Strap
Automatic Backup Inflation
Inflation will occur automatically within 5 seconds after the inflator is
immersed in water. Hydrostatic pressure opens the water inlet valve
allowing the water-sensing element to disintegrate, triggering a spring-
loaded plunger, which punctures the CO2 cylinder inflating the Inflatable
Vest with LIFTTM (Fig. 7).
7
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Hydrostatic inflator must be submerged in at least 4 inches
of water to activate the inflator.
NOTE: When inflated, the carbon dioxide (CO2 gas) used to inflate
PFDs will slowly escape through the cell over time. A slight
reduction of pressure will be observed after several hours of
inflation. Topping up by oral inflation may be required in the
event of prolonged immersion.
Oral Inflation
Properly armed and inspected Inflatable Vest with LIFTTM PFDs will inflate
when manually or automatically activated. However, you can fully inflate
the PFD by mouth (Fig. 8) should inflation not occur, or if you are in a
non-emergency situation.
To orally inflate the PFD, first locate the oral inflation tube by opening
the wearer’s right front panel cover of the PFD. Then remove the dust cap
from the end of the oral tube and blow into the tube until the PFD is
fully inflated.
It may be neccessary to manually release the VelcroTM tabs, located at the
bottom of the left and right panel covers, for full inflation because oral
inflation may not provide sufficient pressure to open the tabs.
CAUTION: CO2 inflation could over-pressurize and damage your
PFD if already orally inflated.
FIGURE 8
Inflatable Vest with LIFTTM Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
8
In-water Adjustments
Follow these instructions to adjust the waist belt, when wearing the
Inflatable Vest with LIFTTM in the water.
To tighten:
a. Grasp the loose end with the left hand. Pull the webbing to your
right side (away from the buckle) (Fig. 9).
b. Simultaneously grasp the waist belt along the body with the right
hand (approximately 6 inches to the right of the buckle), and feed
the webbing into the buckle.
FIGURE 9
To loosen:
a. Simultaneously grasp and hold the waist belt with the left hand as
you grasp the lobe on the right side with the right hand and pull
away from the center (Fig. 10).
FIGURE 10
Waist Belt
9
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Considerations for Automatic Devices
The PFD might not be armed when needed, either knowingly or unknow-
ingly. Premature automatic inflation causes several risks that you must
address to avoid drowning. Much less common but also important are:
1) Double inflation (CO2 cylinder inflation after full oral inflation) could
damage the PFD,
2) Inflation when stored in a tight space could damage the PFD, and
3) The PFD could inflate when you are in an awkward place or position.
If this PFD should inflate, a re-arm kit (MA7218-22), with a valid
install-by-date, is required to re-arm the device.
IMPORTANT: The PFD should be re-armed according to the
Re-arming Your PFD instructions (p. 11).
Deflation
1) To deflate the Inflatable Vest with LIFTTM, reverse the oral inflation
tube dust cap and insert it into the valve or depress valve with a
fingertip. The dust cap will not lock in the deflate position so it is
necessary to hold it in place (Fig. 11).
2) Gently squeeze the Vest until all air or gas has been expelled (Fig.
11). Do not ring or twist (see Re-arming Your PFD (p. 11) and
Repacking (p. 17) sections of this manual).
FIGURE 11
Oral inflation tube
Inflatable Vest with LIFTTM Owner’s Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Usage Below Freezing
When the temperature is below freezing, a fully discharged cylinder
may not adequately inflate your Inflatable Vest with LIFTTM Under these
conditions use the oral inflator to top-up the Inflatable Vest with LIFTTM
It may be neccessary to manually release the VelcroTM tabs, located at the
bottom of the left and right panel covers, for full inflation because oral
inflation may not provide sufficient pressure to open the tabs.
Re-arming Your PFD
NOTE: A valid re-arm kit (MA7218-22) is required for this
procedure.
1) Place the Inflatable Vest with LIFTTM on a smooth, flat surface and
wipe off any water. Access the inflator by reaching under the cover
and fully expose the inflator for re-arming. Hold the CO2 cylinder
through the fabric, using one hand (Fig. 12).
FIGURE 12
11
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Insert the metal key between the black locking ring and labeled
yellow cap. Turn the key counter-clockwise (Fig. 13).
FIGURE 13
Key
Locking Ring
3) Turn the black locking ring counter-clockwise and lift off the cap
(yellow inflator operating head Fig. 14). Dispose of the used cap.
FIGURE 14
Cap
4) Squeeze the sealing ring to elongate and remove the inflator body
(Fig. 15).
Inflatable Vest with LIFTTM Owner’s Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 15
Red Indicator
Inflator Body
Sealing Ring
5) Dispose of the used inflator body.
FIGURE 16
Red Indicator
Trash
6) Check that the new inflator body indicator is green. Insert the new
inflator body with CO2 cylinder pointing upward inside the Inflatable
PFD (Fig. 17). Let the sealing ring rest on the adapter around the four
lugs.
FIGURE 17
Green Indicator
Caution:
Do not turn
the center
shaft
13
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Now check the new manual/automatic cap as follows (Fig. 18):
1. Is the single point status indicator showing green?
2. Is the expiry day OK?
If YES is the answer to both questions, then proceed as follows. If the
answer is NO to either question, get a new cap.
FIGURE 18
Water
Inlet
Valve
Single
Point
Indicator
Expiry
8) Hold the CO2 cylinder through the fabric of the Inflatable Vest with
LIFTTM (Fig. 19). Position the replacement cap with the water inlet
valve pointing to the right and press firmly onto the inflator body
and sealing ring (Fig. 20).
FIGURE 19
FIGURE 20
Inflatable Vest with LIFTTM Owner’s Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9) While pressing FIRMLY onto the inflator body, turn the BLACK
locking ring clockwise into the locked position (Fig. 21). Pull on the
cap to make sure it has locked onto the inflator body.
FIGURE 21
10) Check: To see that the single point status indicator on the cap is
green; the pull to inflate lanyard is present and that the locking ring
is locked.
11) Ensure the beaded handle is fed through the pocket opening and
fastened to the Velcro tab (Fig. 39).
12) Refold the Inflatable Vest with LIFTTM in accordance with the
Repacking section (p. 17).
Auto/Manual Conversion Cap (MA7219) Instructions
These instructions apply only when the MA7219 is used with a MD0450
22 with an armed Hammar M1 inflator - green status indicator.
CONVERSION INSTRUCTIONS
This will convert the MD3196 from an automatic inflation device to
a manual inflation device. The device may be changed back to an
automatic inflation device by removing the conversion cap.
CAUTION: A manual inflation device will not inflate on water
contact unless the wearer activates the inflator.
1) Completely unzip the right lobe zipper (inflator side).
15
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Fasten, by tying, the conversion cap lanyard to the loop in the pocket
immediately in front of the inflator after passing it through the
opening in the cover (Fig.22).
FIGURE 22
Opening
Lanyard
FOLD #1
FOLD #3
FOLD #2
Conversion Cap
Right Lobe
3) Position the conversion cap over the inflator’s hydrostatic valve
opening. The conversion cap’s metal clip should be placed along the
top of the inflator’s hydrostatic valve (Fig.23).
FIGURE 23
4) Secure the conversion cap to the inflator’s hydrostatic valve by
applying pressure to the cap, at the metal clip.
FIGURE 24
Inflatable Vest with LIFTTM Owner’s Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERSION CAP REMOVAL
Once the conversion cap is removed, the MD3196 becomes an automatic
inflation device. Firmly pull the conversion cap lanyard to remove the
conversion cap (Fig.25).
NOTE:Do not pull inflation lanyard when removing conversion cap
FIGURE 25
To remove the conversion cap when packed, pull the conversion cap
lanyard out from the opening of the cover of the LP’s right lobe. Visually
confirm the conversion cap has been removed from the valve opening.
Place the conversion cap in the anti-chafing cover, in the front pocket,
when not in use.
Repacking
IMPORTANT: Carefully read the entire Repacking instructions to
achieve a properly packed Inflatable Vest with LIFTTM
If your Inflatable Vest with LIFTTM has been used and/or the hydrostatic
inflator replaced, always inflate through the oral tube and check that it
stays inflated at least overnight. With the dust cap in the top of the oral
tube, gently squeeze the Inflatable Vest with LIFTTM until all air or gas
has been expelled (Fig. 11). Do not wring or twist the Inflatable Vest with
LIFTTM. Put the oral tube dust cap back in its stowed position on the oral
tube (Fig. 26). Let the life jacket dry before packing.
17
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
1) Before repacking:
Completely deflate the Inflatable Vest with LIFTTM (see Deflation p.
10).
NOTE: Before following the repacking sequence, be sure to
properly re-arm your Inflatable Vest with LIFTTM See Re-arming
Your PFD (p.11).
2) Ensure the oral-inflation dust cap is fitted in the stowed position
(Fig. 26).
FIGURE 26
Dust cap
in stowed
position
Dust cap
position for
deflation
3) Open both front panel covers. Adjust the waist belt and chest belt
buckles to their full lengths so that the Inflatable Vest with LIFTTM is
laid out flat (Fig. 27 shows the right lobe, as worn).
FIGURE 27
FOLD #1
FOLD #3
FOLD #2
Right Lobe
Inflatable Vest with LIFTTM Owner’s Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Lay out flat the right lobe (as it is worn). Shift the left lobe (as it is
worn) on the waist belt to fully extend the right lobe for folding.
NOTE: The numbered fold lines, on the diagram, are provided
to assist with packing. Make each fold towards yourself.
5) Fold the right lobe (as it is worn) over on the Fold #1 dashed line
(Fig. 28). Note that the right lobe has the inflator with cylinder.
FIGURE 28
FOLD #3
FOLD #2
Right Lobe
6) Continuing with the right lobe, fold it over on the Fold #2 dashed
line (Fig. 29). Ensure that the bladder is tucked under the inflator to
prevent it from blocking the indicator window (Point A).
FIGURE 29
D #3
A
19
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Fold the bottom portion of the lobe over (Fig. 30).
a. Position the lobe so it does not cover the inflator (Point A).
b. Put the inflator beaded handle through the opening in the cover
(Point B) and attach to the Velcro tab.
c. Position the chest buckle under the cover (Point C).
FIGURE 30
C
B
A
8) Fold the lobe over on the Fold #3 dashed line (Fig. 31).
a. Position the folded lobe so it does not cover the inflator (Point
A).
FIGURE 31
A
9) Fold the cover panel down so that it covers the lobe (Fig. 32).
Inflatable Vest with LIFTTM Owner’s Manual
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 32
VelcroTM Tab
10) Mustang Survival uses advanced 2-step zippers - SecureZIPTM. Find
the right zipper tail on the right lobe and ZIP 1 - Reset the 2-step
zipper by pulling the slider to the Velcro™ tab (Figs. 33 and 34).
NOTE: Fasten the Velcro™ tab to prevent the zipper from re-
opening.
ZIP 2 - Close by pulling slider in the opposite direction to the end the
zipper (Fig. 34). Ensure that the Inflatable cell does not get caught by
the zipper when closing.
\
FIGURE 33
FIGURE 34
11) Find the left zipper tail on the right lobe and ZIP 1 - Reset the 2-
step zipper by pulling the slider to the Velcro™ tab (Fig. 35).
21
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Fasten the Velcro™ tab to prevent the zipper from re-
opening.
ZIP 2 - Close by pulling slider in the opposite direction to the end the
zipper (Fig. 36). Ensure that the Inflatable cell does not get caught by
the zipper when closing.
\
FIGURE 35
FIGURE 36
12) Tuck in the zipper tail, so it is not exposed (Fig. 37).
FIGURE 37
Zipper
Tail
13) The right lobe should now be fastened closed and the inflator should
be visible through the clear window. Ensure the beaded handle is
placed through the opening and is attached to the Velcro tab on the
outside of the vest (Fig. 39). Ensure the zipper is closed to the stop,
located under the Velcro tab.
NOTE: Ensure the chest buckle does not extend outside of the
Inflatable Vest with LIFTTM Owner’s Manual
22
Download from Www.Somanuals.com. All Manuals Search And Download.
lobe, it should sit under the cover.
14) Repeat steps 3-12 for the left lobe (as it is worn). Note that the left
lobe does not have an inflator or indicator window.
15) Turn over the Inflatable Vest with LIFTTM and fold the back flap up
and fasten the three (3) VelcroTM tabs (Fig. 38).
FIGURE 38
16) Use the adjustable waist belt to size to fit. When complete, the
garment should appear as shown (Fig. 39) and be secure for use or
storage.
FIGURE 39
23
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IS YOUR PFD IN GOOD AND SERVICEABLE CONDITION?
Check your PFD between outings to be sure that it is properly armed,
as shown by green single point indicator; that it is free of rips, tears or
holes; that all seams are securely sewn; and that the fabric, straps and
hardware are still strong. Inspect the inflatable portion of the PFD in
accordance with the CARE AND MAINTENANCE INSTRUCTIONS (p. 24).
CARE AND MAINTENANCE INSTRUCTIONS
It is the responsibility of the wearer to be sure this PFD is in serviceable
condition. To be considered serviceable, this PFD shall not exhibit
deterioration that could diminish its performance, such as broken or
deformed hardware, detached webbing, rotted structural components,
air leaks or nonfunctional inflators. Unless worn inflated, this PFD must
also be properly armed with a cylinder installed in the inflator, and single
point status indicator showing green. See Page 3 for instructions. Failure
to follow these instructions rigorously could result in a non-functioning
PFD causing injury or death.
Check the following at the intervals listed below.
1) Before Each Use:
i) Examine the single point status indicator through the window
panel, ensuring it is green. If the indicator is red, the mechanism
requires service. See Re-arming Your PFD, p. 11.
ii) Ensure the manual beaded handle is accessible.
iii) Visually examine your Inflatable Vest with LIFTTM for damage or
excessive abrasion, wear, tear or contamination. Particular attention
must be paid to the stitching, straps and hardware. If in doubt, send
it to your Mustang dealer for evaluation and/or servicing.
2) Every Six (6) Months:
i) Leak Test: The Inflatable Vest with LIFTTM should be tested for
general leakage by orally inflating your Inflatable Vest with LIFTTM
Inflatable Vest with LIFTTM Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
24
until firm and let stand 2 hours. A leaking Inflatable Vest with LIFTTM
will not hold its firmness and should be replaced. If your Inflatable
Vest with LIFTTM leaks, take it to your Mustang dealer for evaluation
and/or servicing. Repack the Inflatable Vest with LIFTTM as outlined in
the Repacking section (p. 17).
ii) Oral Inflation Valve Test: To check the oral inflation valve, fully
inflate the Inflatable Vest with LIFTTM using the oral inflator and hold
valve under water. If bubbles appear, deflate and re-inflate to test
again. Should the leak persist, take your Inflatable Vest with LIFTTM to
your Mustang dealer for evaluation and/or servicing.
CAUTION: To avoid accidental inflation, don't allow the water
to contact the hydrostatic inflator.
iii) Perform a thorough visual examination. See Readiness
Checklist (p. 4).
Perform these tests more often if exposed to potential damage or
used in extreme conditions.
3) After Each Inflation - Re-arm the Inflatable Vest with LIFTTM. See
Re-arming Your PFD, p. 11.
4) Annually - Perform the following at the beginning of each boating
season, after inflation, or whenever the integrity of the Inflatable
Vest with LIFTTM is in doubt:
i) Check all components for dirt or corrosion. Clean or replace, as
neccessary. See Readiness Checklist (p. 4).
ii) Visually examine your Inflatable Vest with LIFTTM for damage or
excessive abrasion, wear, tear or contamination. Particular attention
must be paid to the stitching, straps and hardware. If in doubt, send
it to your Mustang dealer for evaluation and/or servicing.
iii) Perform the Leak Test. See the Leak Test (section 2) i) in the Care
and Maintenance Instructions).
iv) Perform the Oral Inflation Valve Test: See the Oral Inflation Valve
Test (section 2) ii) in the Care and Maintenance Instructions).
25
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
v) Ensure the current date is not past the date on the inflator. If it
is, replace the inflator (see Re-arming Your PFD, p. 11).
vi) Ensure the single point status indicator is green (Fig. 2).
Repack the Inflatable PFD as outlined in the Repacking section (p. 17).
WARNING: If you are not confident in the self-inspection and
servicing of your Inflatable Vest with LIFTTM in accordance with
these instructions, take your Inflatable Vest with LIFTTM to a
Mustang dealer for professional servicing or contact Mustang
Survival (see contact information on back of manual).
Cleaning and Storing
To avoid inflation, do not submerge the Inflatable Vest with LIFTTM or
directly spray the inflator. Hand wash or sponge down the Inflatable
PFD in warm, soapy water. Rinse the PFD and inflator with clean water,
using a clean rinse cloth. Hang the Inflatable Vest with LIFTTM to dry on a
plastic coat hanger. Do not dry clean.
Always store your Inflatable Vest with LIFTTM in a warm, dry place out of
direct sunlight.
HOW AND WHY TO TEST YOUR PFD
Inflate your Inflatable Vest with LIFTTM and try it out in the water to:
·
·
·
Make sure it floats you:
• Comfortably (when worn properly)
• Adequately for expected wave conditions (body shapes/
densities affect performance)
Make sure it works:
• A flow of bubbles should not appear (see CARE AND
MAINTENANCE INSTRUCTIONS for leak tests p. 24). It should
inflate quick and easily.
Learn how it works by:
Inflatable Vest with LIFTTM Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
26
• Activating the CO2 inflation system
• Re-arming the CO2 inflation system
• Using the oral inflator tube
HOW DO YOU TEST YOUR PFD USING THE AUTOMATIC
INFLATOR?
1) To test your Inflatable Vest with LIFTTM, you will need your fully
armed Inflatable Vest with LIFTTM, and re-arming kit (MA7218-22)
approved for your Inflatable Vest with LIFTTM.
2) Put on the Inflatable Vest with LIFTTM.
3) Get into shallow water, just deep enough that you can stand with
your head above the surface. Once the inflator is underwater, 4
inches or so, the Inflatable Vest with LIFTTM should fully inflate
automatically within 5 seconds.
4) See if the Inflatable Vest with LIFTTM will float you on your back or
just slightly back of vertical. In a relaxed floating position, verify
that your mouth is well above the water’s surface. Note the effect of
where you hold your legs on how you float.
5) Get out of the water and remove the Inflatable Vest with LIFTTM.
6) Deflate the Inflatable Vest with LIFTTM by depressing the oral inflator
valve (see Deflation p. 10). Remove the used inflator.
7) Let the Inflatable Vest with LIFTTM dry thoroughly. Re-arm (p. 11) and
Repack the PFD (p. 17).
HOW DO YOU TEST YOUR PFD USING THE MANUAL
INFLATOR?
1) To test your Inflatable Vest with LIFTTM, you will need your fully
armed Inflatable Vest with LIFTTM, and re-arming kit approved for
your Inflatable Vest with LIFTTM: MA7218-22.
2) Put on the Inflatable Vest with LIFTTM.
27
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Actuate the inflation system by jerking firmly downward on the
beaded handle. The Inflatable Vest with LIFTTM should fully inflate
within 5 seconds.
4) Get into shallow water, just deep enough that you can stand with
your head above the surface.
5) See if the Inflatable Vest with LIFTTM will float you on your back or
just slightly back of vertical. In a relaxed floating position, verify
that your mouth is well above the water’s surface. Note the effect of
where you hold your legs and how you float.
6) Get out of the water and remove the Inflatable Vest with LIFTTM.
Completely deflate the Inflatable Vest with LIFTTM using the oral
inflator (see Deflation p. 10).
7) Let the Inflatable Vest with LIFTTM dry thoroughly. Re-arm (p. 11) and
Repack the PFD (p. 17).
HOW DO YOU TEST YOUR PFD USING THE ORAL
INFLATOR?
This test is not mandatory, however may be conducted using the
following procedure.
WARNING: Use only a previously fired hydrostatic inflator to
perform this test. DO NOT test with a fully armed hydrostatic
inflator as double inflation may occur, possibly resulting in cell
damage.
1) No spare parts or re-arming kits are needed to test your Inflatable
PFD.
2) Put on the Inflatable Vest with LIFTTM.
3) Get into shallow water, just deep enough that you can stand with
your head above the surface.
4) If you are a weak swimmer or non-swimmer, inflate the Inflatable
Vest with LIFTTM partially so that you are supported well enough to
Inflatable Vest with LIFTTM Owner’s Manual
28
Download from Www.Somanuals.com. All Manuals Search And Download.
be able
to complete inflation without touching bottom, either orally or
manually. Note this level of inflation because it is the minimum
needed for you to safely use this Inflatable Vest with LIFTTM.
5) Fully inflate the Inflatable Vest with LIFTTM using the oral inflator.
It may be neccessary to manually release the VelcroTM tabs for full
inflation because oral inflation may not provide sufficient pressure to
open the tabs.
6) See if the Inflatable Vest with LIFTTM will float you on your back or
just slightly back of vertical. In a relaxed floating position, verify
that your mouth is well above the water’s surface. Note the effect of
where you hold your legs and how you float.
7) Get out of the water and remove the Inflatable Vest with LIFTTM.
Completely deflate the Inflatable Vest with LIFTTM using the oral
inflator (see Deflation p. 10).
8) Let the Inflatable Vest with LIFTTM dry thoroughly. Re-arm (p. 11) and
Repack the PFD (p. 17).
Re-assemble inflation system parts and repack the Inflatable Vest with
LIFTTM.
WEAR YOUR PFD
In approximately 80 percent of all boating fatalities, the victims were
not wearing a PFD. Most fatal accidents happen on calm sunny days. This
inflatable PFD is much more comfortable to wear than other PFD types.
Get into the habit of wearing this PFD.
Non-swimmers and children especially should wear a hybrid or
non-inflatable PFD at all times when on or near the water.
29
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
HYPOTHERMIA
Prolonged exposure to cold water causes a condition known as
hypothermia – a substantial loss of body heat, which leads to
exhaustion and unconsciousness. Most drowning victims first suffer from
hypothermia. The following chart shows the effects of hypothermia: how
hypothermia affects most adults.
How hypothermia affects most adults
Water
Exhaustion or
Expected
Temperature ˚C (˚F)
Unconsciousness
Time of Survival
0.3 (33)
Under 15 min.
15–30 min.
30–60 min.
1–2 hrs.
2–7 hrs.
2–12 hrs.
Under 15–45 min.
30–90 min.
1–3 hrs
1–6 hrs.
2–40 hrs.
3 hrs. to Indefinite
Indefinite
0.3–4 (33–40)
4–10 (40–50)
10–16 (50–60)
16–21 (60–70)
21–27 (70–80)
Over 27 (over 80)
Indefinite
PFDs can increase survival time because they allow you to float without
using energy treading water and because of their insulating properties.
Naturally, the warmer the water, the less insulation you will require.
When operating in cold waters [below 60°F (15.6°C)] you should
consider using a coat or jacket style PFD or a Type V Thermal Protective
PFD as they cover more of the body than the vest or belt style PFDs.
Some Points to Remember About Hypothermia Protection:
1) Always wear your PFD. Even if you become incapacitated due to
hypothermia, the PFD will keep you afloat and greatly improve your
chances of rescue.
2) Do not attempt to swim unless it is to reach a nearby craft, fellow
survivor, or a floating object on which you can lean or climb.
Swimming increases the rate of body heat loss. In cold water, drown-
proofing methods that require putting your head in the water are
not recommended. Keep your head out of the water. This will greatly
Inflatable Vest with LIFTTM Owner’s Manual
30
Download from Www.Somanuals.com. All Manuals Search And Download.
lessen heat loss and increase your survival time.
3) Use the standard H.E.L.P. position when wearing an inflatable PFD,
drawing the legs up to a seated position, because doing so will help
you conserve body heat (Fig. 36).
4) Keep a positive attitude about your survival and rescue. This will
improve your chances of extending your survival time until rescued.
Your will-to-live does make a difference!
5) If there is more than one person in the water, huddling is
recommended while waiting to be rescued. This action tends to
reduce the rate of heat loss and thus increase the survival time.
FIGURE 36
EACH OF THESE DEVICES IS INTENDED TO HELP YOU
SAVE YOUR OWN LIFE
For your PFD to function properly, follow these suggestions to verify that
it fits, floats, and remains in good condition.
1) Check the inflation mechanism status indicator before each use.
2) Get in the habit of re-arming the inflation mechanism immediately
after each CO2 inflation (be sure the inflator is dry before re-arming).
3) Try your wearable PFD on and adjust it until it fits comfortably in
and out of the water.
4) Mark your PFD with your name if you are the only wearer.
5) Do not alter your PFD. If it doesn’t fit properly, get one that does.
6) Your PFD is not intended for use as a fender or kneeling pad.
31
MUSTANG SURVIVAL
Download from Www.Somanuals.com. All Manuals Search And Download.
7) If your PFD is wet, allow it to dry thoroughly before storing it.
Store it in a well-ventilated area.
8) Do not dry your PFD in front of a radiator or other source of
direct heat.
SAFETY ACCESSORIES
For the MD0450 22 use a MA7218-22 Re-arm Kit, which includes a 38-
gram CO2 replacement cylinder, inflator body and beaded handle.
DO NOT ATTACH PFD’S TO YOUR BOAT
Each PFD has straps, hooks, buckles, or other means for securing the
device in place on the wearer. Some PFDs also incorporate decorative
D-rings or tabs. Such items are not to be used to attach the device
to the boat. Attaching the device to the boat will not permit it to perform
as intended.
AIRLINE OPERATOR POLICY ON CARRIAGE OF
INFLATABLE PFDS AND CO2 CARTRIDGES
Please be aware that the following regulations apply to the air transport
of this product. According to U.S. Department of Transportation (DOT),
PHMSA - the Pipeline and Hazardous Materials Safety Administration
Title 49 CFR 75.10(a)(25): With the approval of the aircraft operator, one
small carbon dioxide cylinder (not installed), plus one spare cartridge,
may be carried by a passenger or crew as checked baggage.
Please refer to the governing body’s documentation, found online at
Inflatable Vest with LIFTTM Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
32
�
WE SAVE LIVES FOR A LIVING
3870 Mustang Way
Bellingham,WA
USA 98226
TOLL FREE
1.800.526.0532
EMAIL
WEB
Mustang Survival and seahorse design are registered trademarks of Mustang Survival Corp.
Our commitment to quality has earned our Richmond facilities ISO 9001 registration,
the highest of all international standards. This is our guarantee you’re receiving the ultimate
in design and manufacturing.
Printed in Canada (Rev 30 Mar 07)
Download from Www.Somanuals.com. All Manuals Search And Download.
|