Multiquip Trash Compactor MVH 402DSB User Manual
OPERATION AND PARTS MANUAL  
Reversible Plate  
Compactor  
Model MVH-402DSB  
Revision #2 (03/30/05)  
MULTIQUIPINC.  
18910 WILMINGTON AVE.  
PARTS DEPARTMENT:  
800-427-1244  
CARSON, CALIFORNIA 90746 FAX: 800-672-7877  
310-537-3700  
800-421-1244  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:  
800-478-1244  
FAX:310-537-3927  
FAX:310-631-5032  
E-mail:mq@multiquip.com • www:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Montreal, Canada • Manchester, UK  
Rio De Janiero, Brazil • Guadalajara, Mexico  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
MULTIQUIP’SMAINPHONENUMBERS  
800-421-1244  
310-537-3700  
FAX: 310-537-3927  
PARTSDEPARTMENT  
800-427-1244  
310-537-3700  
FAX: 800-672-7877  
FAX: 310-637-3284  
MAYCOPARTS  
800-306-2926  
310-537-3700  
FAX: 800-672-7877  
FAX: 310-637-3284  
SERVICEDEPARTMENT  
800-478-1244  
310-537-3700  
FAX: 310-537-4259  
MQPOWERSERVICEDEPARTMENT  
800-835-2551  
310-537-3700  
FAX: 310-638-8046  
TECHNICALASSISTANCE  
800-478-1244  
FAX: 310-631-5032  
WARRANTYDEPARTMENT  
800-421-1244, EXT. 279 FAX: 310-537-1173  
310-537-3700, EXT. 279  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Proposition 65 Warning ............................................. 2  
Here's How To Get Help ............................................ 3  
Table Of Contents ..................................................... 4  
Parts Ordering Procedures ....................................... 5  
Yanmar L100EE-DEVMK1 Engine  
Cylinder Block Assembly.................................... 46-47  
Cylinder Head and Cover Assembly .................. 48-49  
Muffler Assembly ............................................... 50-51  
Air Cleaner Assembly......................................... 52-53  
Crankshaft, Piston and Camshaft Assembly ..... 54-55  
Lub. Oil Pump and Governor Assembly ............. 56-57  
Cooling and Starting Device Assembly.............. 58-59  
Fuel Injection Pump Assembly........................... 60-61  
Fuel Tank and Fuel Line Assembly .................... 62-63  
Starting Motor and Dynamo Assembly .............. 64-65  
Tool, Label and Gasket Set Assembly ............... 66-67  
MIKASA MVH-402DSB-  
PLATE COMPACTOR  
Safety Message Alert Symbols .............................. 6-7  
Rules for Safe Operation ....................................... 8-9  
Operation and Safety Decals .................................. 10  
Specifications .......................................................... 11  
Dimensions ............................................................. 12  
Features.................................................................. 13  
Plate Compactor Components................................ 14  
Engine Components ............................................... 15  
Operation ........................................................... 16-19  
Maintenance ...................................................... 20-23  
Troubleshooting ................................................. 24-25  
Terms and Conditions Of Sale — Parts .................. 68  
PARTS ILLUSTRATIONS  
Explanation Of Code In Remarks Column .............. 26  
Suggested Spare Parts ........................................... 27  
Decal Placement ................................................ 28-29  
Vibrating Plate Assembly ................................... 30-31  
Base and Engine Assembly ............................... 32-35  
Vibrator Assembly .............................................. 36-39  
Hydraulic System Assembly............................... 40-41  
Control Handle Assembly .................................. 42-45  
PAGE 4 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
■ Dealer account number  
■ Dealer name and address  
■ Shipping address (if different than billing address)  
■ Return fax number  
■ Applicable model number  
■ Quantity, part number and description of each part  
■ Specify preferred method of shipment:  
UPS Ground  
•
UPS Second Day or Third Day*  
•
UPS Next Day*  
•
Federal Express Priority One (please provide us with your Federal  
Express account number)*  
•
Airborne Express*  
•
Truck or parcel post  
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.  
Earn Extra Discounts when  
you order by FAX!  
All parts orders which include complete part numbers  
and are received by fax qualify for the following extra  
discounts:  
Number of  
line items ordered  
Additional Discount  
1-9 items  
3%  
10+ items**  
5%  
only  
s
der  
ed or  
x
a
f
For  
Get special freight allowances  
when you order 10 or more  
line items via FAX!**  
Now! Direct TOLL-FREE access  
to our Parts Department!  
■
UPS Ground Service at no charge for freight  
■
PS Third Day Service at one-half of actual freight cost  
Toll-free nationwide:  
800-421-1244  
No other allowances on freight shipped by any other carrier.  
**Common nuts, bolts and washers (all items under $1.00 list price)  
do not count towards the 10+ line items.  
Toll-free FAX:  
*DISCOUNTS ARE SUBJECT TO CHANGE*  
800/6-PARTS-7 • 800-672-7877  
Fax order discount and UPS special programs revised June 1, 1995  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — SAFETY MESSAGE ALERT SYMBOLS  
HAZARD SYMBOLS  
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!  
Safety precautions should be followed at all times when  
operating this equipment. Failure to read and understand the  
Safety Messages and Operating Instructions could result in  
injury to yourself and others.  
Lethal Exhaust Gases  
Engine exhaust gases contain poisonous  
NOTE  
carbon monoxide. This gas is colorless and  
odorless, and can cause death if inhaled.  
NEVER operate this equipment in a confined  
area or enclosed structure that does not  
provide ample free flow air.  
This Owner's Manual has been developed to provide  
complete instructions for the safe and efficient operation  
of the Multiquip Model MVH-402DSB Reversible Plate  
Compactor. Refer to the engine manufacturer’s  
instructions for data relative to its safe operation.  
Before using this reversible plate compactor, ensure  
that the operating individual has read and  
understands all instructions in this manual.  
Explosive Fuel  
GASOLINE is extremely flammable, and its  
vapors can cause an explosion if ignited. DO  
NOT start the engine near spilled fuel or  
combustible fluids. DO NOT fill the fuel tank  
while the engine is running or hot. DO NOT  
overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or  
sparks from the ignition system. Store fuel in  
approved containers, in well-ventilated areas  
and away from sparks and flames. NEVER  
use fuel as a cleaning agent.  
SAFETY MESSAGE ALERT SYMBOLS  
The three (3) Safety Messages shown below will inform you  
about potential hazards that could injure you or others. The  
Safety Messages specifically address the level of exposure to  
the operator, and are preceded by one of three words: DANGER,  
WARNING, or CAUTION.  
Burn Hazards  
DANGER: You WILL be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Engine components can generate extreme heat.  
To prevent burns, DO NOT touch these areas  
while the engine is running or immediately after  
operations. Never operate the engine with heat  
shields or heat guards removed.  
WARNING: You CAN be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Rotating Parts  
CAUTION: You CAN be injured if you  
do not follow directions.  
NEVER operate equipment with covers, or  
guards removed. Keep fingers, hands, hair and  
clothing away from all moving parts to prevent  
injury.  
Potential hazards associated with this reversible plate  
compactor operation will be referenced with Hazard Symbols  
which appear throughout this manual, and will be referenced in  
conjunction with Safety Message Alert Symbols.  
PAGE 6 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — SAFETY MESSAGE ALERT SYMBOLS  
Accidental Starting  
Respiratory Hazard  
ALWAYS place the engine ON/OFF switch in  
the OFF position, when the reversible plate  
compactor is not in use.  
ALWAYS wear approved respiratory  
protection.  
Equipment Damage Messages  
Sight and Hearing hazard  
Other important messages are provided throughout this manual  
to help prevent damage to your reversible plate compactor,  
other property, or the surrounding environment.  
ALWAYS wear approved eye and hearing  
protection.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — RULES FOR SAFE OPERATION  
■
NEVER touch the hot exhaust manifold,  
muffler or cylinder. Allow these parts to  
cool before servicing engine or  
reversible plate compactor.  
CAUTION:  
Failure to follow instructions in this manual  
may lead to serious injury or even death!This  
equipment is to be operated by trained and  
qualified personnel only! This equipment is  
for industrial use only.  
The following safety guidelines should always be used when  
operating the MIKASA MVH-402DSB Reversible Plate  
Compactor:  
■
■
HighTemperatures – Allow the engine to cool before adding  
fuel or performing service and maintenance functions. Contact  
with hot components can cause serious burns.  
The engine of this reversible plate compactor requires an  
adequate free flow of cooling air. NEVER operate the  
reversible plate compactor in any enclosed or narrow area  
where free flow of the air is  
restricted. If the air flow is  
restricted it will cause serious  
damage to the reversible plate  
compactor or engine and may  
GENERAL SAFETY  
■
■
■
DO NOT operate or service this equipment before  
readingthisentiremanual.  
This equipment should not be operated by  
persons under 18 years of age.  
cause injury to people and  
property. Remember the  
vibration roller's engine gives  
off DEADLY gases.  
NEVER operate this equipment without proper  
protective clothing, shatterproof glasses, steel-  
toed boots and other protective devices required  
by the job. ALWAYS wear slip resistant safety  
shoes or boots.  
■
■
ALWAYS refuel in a well-ventilated area, away from sparks  
and open flames.  
ALWAYS use extreme caution when working with flammable  
liquids. When refueling, stop the engine and allow it to cool.  
DO NOT smoke around or near the machine. Fire or  
explosion could result from fuel vapors, or if fuel is spilled on  
a hot engine.  
■
■
■
NEVER operate this equipment when not feeling  
well due to fatigue, illness or taking medicine.  
NEVER operate this equipment under the  
influence or drugs or alcohol.  
■
NEVER operate the reversible plate compactor in an  
explosive atmosphere or near  
combustible materials. An explosion or  
fire could result causing severe bodily  
harm or even death.  
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
■
■
■
■
■
Topping-off to filler port is dangerous, as  
it tends to spill fuel.  
■
■
■
Manufacturer does not assume responsibility for any accident  
due to equipment modifications.  
ALWAYS store the reversible plate compactor in a clean, dry  
location out of the reach of children.  
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
NEVER run engine without air cleaner. Severe engine  
damage may occur.  
ALWAYS wear proper respiratory (mask), hearing and eye  
protection equipment when operating the reversible plate  
compactor.  
NEVER leave the reversible plate compactor unattended,  
turn off engine.  
CAUTION must always be observed while servicing this  
reversible plate compactor.Rotating parts can cause injury if  
contacted.  
■
DO NOT leave reversible plate compactor with engine  
running. Use chock blocks if parking reversible plate  
compactor on a grade.  
PAGE 8 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — RULES FOR SAFE OPERATION  
■
NEVER disconnect any "emergency or safety devices".  
These devices are intended for operator safety. Disconnection  
of these devices can cause severe injury, bodily harm or even  
death! Disconnection of any of these devices will void all  
warranties.  
■
ALWAYS know the location of the nearest first aid kit.  
Loading and Unloading (Crane)  
■
Before lifting, make sure that machine parts (hook and  
vibration insulator) are not damaged and screws are not  
loosened or lost.  
■
In emergencies always know the location of the  
nearest phone or keep a phone on the job site.  
Also know the phone numbers of the nearest  
ambulance, doctor and fire department. This  
information will be invaluable in the case of an  
emergency.  
■
Always make sure crane or lifting device has been properly  
secured to the hook of guard frame on compactor.  
■
■
■
■
NEVER lift the machine while the engine is running.  
Use adequate lifting cable (wire or rope) of sufficient strength.  
Use one point suspension hook and lift straight upwards.  
NEVER allow any person or animal to stand underneath the  
machine while lifting.  
■
Try not to lift machine to unnecessary heights.  
Transporting  
■
■
ALWAYS shutdown engine before transporting.  
Tighten fuel tank cap securely and close fuel cock to prevent  
fuel from spilling.  
■
■
Drain fuel when transporting compactor over long distances  
or bad roads.  
ALWAYS tie down the compactor during transportation by  
securing the compactor's guard frame with rope.  
Emergencies  
■
ALWAYS know the location of the nearest fire extinguisher.  
Maintenance Safety  
■
NEVER lubricate components or attempt service on a  
running machine.  
■
ALWAYS allow the machine a proper amount of time to  
cool before servicing.  
■
■
Keep the machinery in proper running condition.  
Fix damage to the machine immediately and always replace  
broken parts.  
■
Dispose of hazardous waste properly. Examples of  
potentially hazardous waste are used motor oil, fuel and  
fuel filters.  
■
■
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
DO NOT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — OPERATION AND SAFETY DECALS  
Figure 1 displays the operation and safety decals as they appear on the reversible plate compactor. Should any of these decals  
become damaged or unreadable, contact the Multiquip Parts Department for a replacement set.  
Figure 1. Operation and Safety Decals  
PAGE 10 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —SPECIFICATIONS  
Table 1. MVH-402DSB REVERSIBLE PLATE COMPACTOR SPECIFICATIONS  
Centrifugal Force  
54.9 kN (5600 kg)  
Vibration Frequency  
Traveling Speed  
4200 vpm (70 Hz)  
0 to 75.5 ft/min (0 to 20 m/min)  
39 x 21.7 in (990 x 550 mm)  
65.4 in (1600 mm)  
Plate Size (L x W)  
Overall Length  
Overall Width  
21.7 in (550mm )  
Overall Height  
39.8 in (1010 mm )  
981 lbs. (445 kg)  
Operating Weight  
Lubricating Oil in Vibration Case  
43.9 fl oz (1300 cc)  
Table 2. ENGINE SPECIFICATIONS (YANMAR)  
Engine Make  
YANMAR  
Engine Model  
L100EE-DEVMK1  
Diesel  
Engine Type  
Cylinder Bore X Stroke  
Displacement  
3.46 x 2.75 in (88 x 70 mm)  
13.7 fl oz (406 cc)  
10 HP  
Maximum Ouput  
Fuel Tank Capacity  
Oil Capacity  
5.8 quarts (5.5 liters)  
1.74 quarts (1.65 liters)  
116.6 lbs. (53 kg)  
16.4 x 18.5 x 19.4 in (417 x 470 x 494 mm)  
Dry Net Weight  
Dimensions (L x W x H)  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — DIMENSIONS  
TABLE 3. DIMENSIONS  
REF.  
A
DIMENSIONS  
53 in. (134.6 cm.)  
24 in. (61 cm.)  
B
C
34 in. (86 cm.)  
D
63.8 in. (162 cm.)  
38.2 in. (97 cm.)  
E
Figure 2. MVH-402DSB Reversible Plate Compactor Dimensions  
PAGE 12 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — FEATURES  
Plate Compactor  
Frequency/Speed  
The Mikasa MVH-402DSB is a walk behind, reversible plate  
compactor designed for the compaction of sand, clay and  
asphalt. This plate compactor is a powerful compacting tool  
capable of applying a tremendous force in consecutive high  
frequency vibrations to a soil surface. Its applications include  
soil compacting for road, embankments and reservoirs as well  
as backfilling for gas pipelines, water pipelines and cable  
installation work.  
The compactor's vibrating plate maximum frequency is 4200  
vpm (vibrations per minute).The forward and reverse travel speed  
of the compactor is approximately 75.5 ft./minute (23 meters/  
minute).  
Engine  
The Mikasa MVH-402DSB Plate Compactor is equipped with a  
Yanmar L100EE-DEVMK1 diesel engine.  
Controls  
Vibratory Plates  
Before starting the MVH-402DSB Plate Compactor, identify and  
understand the function of the controls and components as  
indicated in Figure 3.  
The vibratory plates of the MVH-402DSB produce low amplitude  
high frequency vibrations, designed to compact granular soils.  
The resulting vibrations cause forward motion.The engine and  
handle are vibration isolated from the vibrating plate.The heavier  
the plate, the more compaction force it generates.  
ReversibleVibratory Plates  
Reversible vibratory plates have two eccentric weights that allow  
a smooth transition for forward and reverse travel, plus increased  
compaction force as the result of dual weights.  
Due to their weight and force, reversible plates are ideal for  
semi-cohesive soils.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB— PLATE COMPACTOR COMPONENTS  
Figure 3. MVH-402DSB Reversible Plate Compactor Components  
Figure 3 illustrates the location of the major components  
for the MVH-402DSB Reversible Plate Compactor. The  
function of each component is described below:  
7.  
Battery - Maintenance-free type requiring no electrode  
replenishment.  
8. Belt Cover – Remove this cover to gain access to the V-  
belts.NEVER run the compactor without theV-belt cover.If  
the V-belt cover is not installed, the possibility exist that  
your hand may get caught between the V-belt and clutch,  
thus causing serious injury and bodily harm.  
1. Hand Grip – When operating the compactor use this hand  
grip to manuever the compactor.  
2. Forward & Reverse Lever – Push the lever forward, the  
compactor will move in a forward direction, pull the lever  
backwards, the compactor will move in backwards direction.  
Placing the lever in the middle (midway) will cause the  
compactor not to move (neutral).  
9. Base Plate – Designed to compact sand, clay, and asphalt.  
10. OilTank – Fill with proper grade of diesel engine oil.  
11. Vibration Case – Encloses the eccentric, gears and  
3. Handle Bar – When operating the compactor, this handle  
is to be in the downward position. When the compactor is  
to be stored, move the handle bar to the upright position.  
counter weights.  
12. Shock Absorber – Protects plate compactor from damage  
by absorbing vibration during operation.  
4.  
Guard Hook - Used to lift the machine with crane or other  
lifting device.  
13. Throttle Lever – Controls the speed of the plate compactor.  
Place straight vertically to start, push fully counterclockwise  
for full trottle and fully clockwise to stop plate compactor.  
5.  
Stopper - Locks the handle in place in the upward postion  
for stowing.  
6. Engine – This plate compactor uses a YANMAR L100EE-  
DEVMK1 diesel engine. Refer to the owner’s manual for  
engine information and related topics.  
PAGE 14 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB— ENGINE COMPONENTS  
Figure 4. MVH-402DSB Engine Components  
ENGINE COMPONENTS  
Figure 4 illustrates the location of the major engine  
components of the machine. Each component is described  
below:  
6.  
Recoil Starter – Housing for pull rope and starter.  
7. Oil Filler Cap/Dipstick – Remove this cap to add oil to the  
oil tank. Use dipstick to check oil level.  
1. Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank.Make sure cap is tighten securely.  
DO NOT over fill.  
8.  
Oil Drain Plug – Unscrew plug to drain oil from engine  
crankcase.Dispose of oil in a safe manner.  
9. Decompression Lever – Press down before starting  
engine.To prevent damage to the engine, DO NOT use for  
any other purpose.  
2. FuelTank – Diesel engine holds 5.8 quarts of diesel fuel.  
3. Air Cleaner – Prevents dirt and other debris from entering  
the fuel system. Remove wing-nut on top of air filter  
cannister to gain access to filter element.  
10. Fuel Cock – Controls the flow of diesel fuel to the carburetor.  
Must be in the ON position when starting and running the  
engine.  
4. Muffler – Used to reduce noise and emissions.  
5. Recoil Starter (pull rope) –Type of engine starting method.  
Alternate type would be electric start (ignition key).  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — PRE-INSPECTION  
3. If the oil level is low, fill to the edge of the oil filler  
hole with the recommended oil type (Table 4).  
Maximum oil capacity is 1.74 quarts (1.65 liters).  
CAUTION  
Never  
operate  
the  
compactor in a confined  
area or enclosed structure  
that does not provide ample  
Table 4. Oil Type  
Season  
Summer  
Spring/Fall  
Winter  
Temperature  
(25°C or Higher)  
(25°C~10°C)  
Oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
free flow of air.  
ALWAYS wear approved eye and hearing  
protection before operating the compactor.  
Lower than10°C  
Before Starting  
1.  
Read safety instructions at the beginning  
of manual.  
Explosive Fuel  
2.  
Familiarize yourself with the operating  
and control elements of the machine and  
the working environment.This includes obstacles in the  
working area, bearing capacity of the ground and the  
necessary safety provisions.  
DANGER  
Diesel fuel is highly flammable and can be danger-  
ous if mishandled. DO NOT smoke while refueling.  
DONOTattempttorefuelthecompactoriftheengine  
is hot! or running.  
3. Check the air filter for dirt and dust. If the air filter is dirty,  
replace air filter with a new one as required.  
Checking The Fuel  
4.  
5.  
6.  
Check fastening nuts and bolts for tightness. Loose threads  
may cause damage to the machine when vibrating.  
1. Remove the fuel cap located on top of fuel tank.  
2. Visually inspect to see if fuel level is low. If fuel is low,  
replenish with diesel fuel (Figure 6).  
Understand the geographical features and regulations of  
the job site.  
Clean the compactor, removing dirt and dust, particularly,  
the bottom of the plate, engine cooling air inlet.  
3. When refueling, be sure to use a strainer for filtration. DO  
NOT top-off fuel. Wipe up any spilled fuel.  
Checking Engine Oil Level  
1. Make sure that the machine is situated in a flat  
surface so that level measurements will be accurate.  
2. Pull out the dipstick from the oil tank (Figure 5).  
CAUTION  
DO NOT overfill oil tank. This could cause oil  
leaks and sluggish operation. Clean cap and  
surrounding area before opening to prevent dirt  
from entering tank.  
Figure 6. Refueling  
DANGER  
Fuel spillage on a hot engine can case a fire or  
explosion.Iffuelspillageoccurs,wipeupthespilled  
fuel completely to prevent fire hazards. NEVER!  
smokearoundornearthecompactor.  
Figure 5. Oil Dipstick Removal  
PAGE 16 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — OPERATION  
CAUTION  
DO NOT attempt to operate the compactor until the Safety,  
General Information and Inspection sections of this manual have  
been read and thoroughly understood.  
This section is intended to assist the operator with the initial  
start-up of the compactor.It is extremely important that this section  
be read carefully before attempting to use the compactor in the  
field.  
Figure 9. Throttle Lever (Start)  
3. Insert the starter key into the key switch and turn it to  
the RUN position (Figure 10). The buzzer should  
sound at this time.  
Refer to Figures 3 and 4 for the location of controls and  
components.  
4. Turn the starter key further to the right to the START  
position to start the engine. Buzzer stops sounding  
and the engine starts.  
Adjusting Handle Height  
5.  
If the engine fails to start, DO NOT continue to rotate  
the starter key for more than 5 seconds. Return the  
key to the RUN position and wait 10 seconds before  
starting again.  
The height of the handle is adjustable for your comfort .  
1. Loosen the butterfly screw (Figure 7).  
2. Turn the grip clockwise to raise the handle or counterclock-  
wise to lower the handle.  
3. When the handle is raised to the desired height, tighten the  
butterflyscrew.  
Figure 10. Starter Switch  
CAUTION  
While the engine is running, never try to turn  
the starter key to the START position.  
Figure 7. Handle Adjustment  
STARTING THE ENGINE  
Electric Start  
6. After starting the engine, continue to warm up the  
engine for about 3 to 10 seconds especially in cold  
weather.  
1.  
Open the fuel cock (Figure 8).  
7. If the buzzer does not stop sounding after the engine  
has started, shutdown engine immediately and check  
engine oil level. The buzzer functions as engine oil  
level warning also.  
When starting a unit with  
anelectric start capability, a  
decompressor is not normally  
NOTE  
Figure 8. Open Fuel Cock  
required. However, when  
ambient temperature or  
battery charger level is low,  
use of a decompressor will  
help make the start-up easier.  
2.  
Move the throttle lever to the START position by opening it  
to about 20 degrees (Figure 9).  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—OPERATION  
Recoil Start  
1. Graspthecompactor'shandgrip(Figure13), andmovethe  
engine throttle lever (Figure 13) quickly to the fastposition.  
1.  
2.  
Open the fuel cock (Figure 8).  
Move the throttle lever to the START position by opening  
it to about 20 degrees (Figure 9).  
2. With the throttle lever in the fast position, the engine speed  
should be around 2,300 RPM, therefore engaging the cen-  
trifugalclutch.  
3. Grasp the starter grip (Figure 11) and slowly pull it  
out. The resistance becomes the hardest at a certain  
position, corresponding to the compression point.  
Pull the starter grip briskly and smoothly for starting.  
Figure 13. Throttle Lever ((Fast)  
Figure 11. Engine Start Handle  
ALWAYS move the throttle lever  
4. Push down decompression lever (Figure 12) and  
release.  
NOTE  
quickly without hesitation, because  
increasing the engine speed slowly  
causes the clutch to slip.  
3. To make the compactor move in the forward direction push  
the travel lever ( Figure 14) forward.  
Figure 12. Decompression Lever  
5. If the engine does not start, repeat steps 4 and 5.  
TRAVELING  
CAUTION  
Makesuretofollowallsafetyrulesreferencedinthe  
safetysectionofthismanualbeforeoperatingcom-  
pactor. Keep work area clear of debris and other  
objectsthatcouldcausedamage tothecompactor  
or bodily injury.  
Figure 14. Direction Lever  
PAGE 18 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—OPERATION  
STOWING THE HANDLE  
1. Push up the handle (Figure 17).  
4. Tomakethecompactormoveinthereversedirectionpullthe  
travel lever ( Figure 13) backwards.  
2. Pull the stopper grip upward into the hole of the guard  
frame to lock the handle.  
5. Firmly gasp the compactor's hand grip, the compactor will  
beginmovinginthedesiredpositionwhenthedirectionlever  
has been placed in the desired position.  
6. Slowlywalkbehindthecompactorandbeonthelookout for  
anylargeobjectsorforeignmatterthatmightcausedamage  
to the compactor or bodily injury.  
7. Iftravelleverisplacedintheneutralposition,themachinewill  
vibrate in place.  
8. Tomovethecompactorlaterally,holdthehandgripfirmlyand  
swingcompactor. Donotswingcompactorwhilegrippingthe  
travel lever.  
STOPPING  
1.  
Return the throttle lever to the START position  
(Figure 9). Allow the machine to cool down for 2 to 3  
minutes.  
2. Turn the throttle lever to the STOP position (Figure  
15) to stop the engine. In a motor start, return the key  
switch to the STOP position (Figure 16) as soon as  
the engine stops.  
Figure 17. Stowing the Handle  
LIFTING  
1.  
2.  
3.  
4.  
5.  
Use a crane or lift to load and unload the machine. A  
skilled crane operator is required to perform the job.  
3. Close the fuel cock (Figure 8).  
When lifting the machine, check for any damaged or  
loose bolts, lifting hooks, and shock mounts.  
Check any damaged or loose bolts in the guard frame to  
avoid machine sliding off.  
Make sure that the machine is shut off before machine is  
lifted.  
Use reliable cable for lifting.  
6. Always lift the machine vertically and keep the  
machine away from workers and animals.  
Figure 15. Throttle Lever (Stop)  
7.  
Do not lift the machine higher than the required  
height.  
TRANSPORTING  
1. Always make sure that the machine is shut off while  
being transported.  
2. Check that the fuel cap is properly closed and  
tightened.  
Figure 16. Starter Switch (STOP)  
Emergency Shutdown  
3. When traveling long distances or on rugged terrain,  
drain the fuel of the machine before transporting.  
1. Move the throttle lever quickly to the STOP position,  
and place the engine IGNITION switch in the OFF  
position.  
4. Tie down the machine securely on the  
transportation so that it will not move or topple over.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — MAINTENANCE  
CAUTION  
CAUTION  
Inspection and other services should always be  
carried out on hard and level ground with the engine  
shutdown.  
Fuel piping and connections should be replaced  
every 2 years.  
Inspection and Maintenance ServiceTables.  
TABLE 6. MVH-402DSB ENGINE CHECK  
1. To make sure your plate compactor is always in good  
working condition before using, carry out the maintenance  
inspection in accordance with Tables 5 through 7.  
ITEM  
HOURS OF OPERATION  
Oil or Fuel Leak  
Every 8 hours (every day)  
Every 8 hours (every day)  
TABLE 5. MVH-402DSB MACHINE INSPECTION  
Tightness of Fastening  
Threads  
HOURS OF  
OPERATION  
ITEM  
REMARKS  
Every 8 hours (every day)  
(Replenish to specified maximum  
level)  
Engine Oil Check and  
Replenishment  
Loose or Missing  
Screws  
Every 8 hours  
(every day)  
After first 25 hours then every 50 to  
100 hours  
Engine Oil Replacement  
Air Filter Cleaning  
Every 8 hours  
(every day)  
Damaged Parts  
Every 100 hours  
Function of Controlling Every 8 hours  
System Part (every day)  
See separate engine manual for details on engine check.  
Daily Service  
Hydraulic System Leak Every 100 hours  
See page 22  
See page 24  
z
Check for leakage of fuel or oil.  
Vibrator Oil Check  
Every 100 hours  
Every 300 hours  
z
Check for loose screws including tightness. See Table 7  
below (tightening torque ), for retightening:  
Vibrator Oil  
Replacement  
See page 24  
See page 24  
TABLE 7.  
Hydraulic Oil Check  
Every 100 hours  
First after 200  
hours, then every See page 24  
1,000 hours  
TIGHTENING TORQUE (in. kg/cm) Diameter  
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm  
Hydraulic Oil  
Replacement  
4T  
70  
150  
250  
400  
300  
500  
800  
500  
800  
750  
1,100 1,400  
2,000  
3,800  
5,600  
6-8T  
11T  
100  
150  
1,300 2,000 2,700  
V-belt (clutch) Check  
Battery Check  
Every 200 hours  
Every 100 hours  
See page 23  
See page 25  
1,200 2,000 2,900 4,200  
300~ 650 ~  
350 700  
*
100  
* (In case counter-part is of aluminum)  
(Threads in use with this machine are all right handed)  
Material and quality of material is marked on each bolt, and screw.  
CAUTION  
These inspection intervals are for operation under  
normal conditions. Adjust your inspection intervals  
based on the number hours plate compactor is in  
use, and particular working conditions.  
z
z
Remove soil and clean the bottom of compaction plate.  
Check hydraulic pump, piping and hose for any leakage. A  
loosened hydraulic hose can be a cause for leakage. Check  
hydraulic hose connections with wrench applied for  
tightness.  
z
Check engine oil.  
PAGE 20 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — MAINTENANCE  
Engine Oil Replacement:  
1. Replace engine oil, first in 25 hours of operation and every  
50 to 100 hours afterwards.  
2. Oil may be drained more easily when it is warm after  
operation (For more details, see separate engine Owner's  
Manual).  
Air Filter  
1. The air filter element should be cleaned because a clogged  
air cleaner can cause poor engine starting, lack of power  
and shorten engine life substantially.  
Figure 20. V-Belt Check  
Replacing the V-belt  
z
Remove the belt cover. Engage an offset wrench (19 mm) or the  
like to vibrator pulley (lower) fastening bolt. Engage waste cloth  
or the like at midway ofV-belt on the left side and while pulling it  
back strongly, rotate the offset wrench clockwise so that the V-  
belt will come off.  
z
Reinstalling the V-belt  
Figure 18. Engine Air Filter and Element  
EngageV-belt to lower vibrator pulley and push theV-belt to left  
side of upper clutch and, in the same manner as in removal,  
rotate offset wrench clockwise so that the V-belt goes back on.  
2. To clean or replace air filter loosen the wing nut on the air  
filter housing (Figure 18), remove the cover and take out air  
filter cartridge. If only cleaning of the air filter is desired blow  
through the air filter cartridge from the inside, moving a jet of  
dry compressed air up and down until all dust is removed.  
z
Checking Clutch  
Check the clutch simultaneously withV-belt checking. With belt  
cover removed, check outer drum of the clutch for seizure and  
"V" groove for wear or damage with your eyes. Clean the "V"  
groove as necessary. Wear of lining or shoe should be checked  
with running check. If the shoe is worn, power transmission  
becomes deficient and slipping will result.  
CAUTION  
NEVER attempt to check theV-belt with the engine  
running. Severe injury can occur if your hand gets  
caughtbetweentheV-beltandtheclutch(Figure19).  
Alwaysusesafetygloves.  
z
Replacing Clutch  
CLUTCH  
PULLEY  
RemoveV-belt.Remove bolt at engine power output by giving a  
shock to an engaged wrench (tapping with hammer or the like)  
and rotating bolt counterclockwise. Remove clutch with a pulley  
extractor.To reinstall, reverse the procedure.  
VIBRATOR  
PULLEY  
CAUTION  
Figure 19. V-Belt Hazard  
Wheneverthecompactor'svibrationbecomesweak  
orlostduringnormaloperationregardlessofopera-  
tion hours, check theV-belt and clutch immediately.  
Checking and Replacing the V-Belt and Clutch  
1. After 200 hours of operation, remove the belt cover to check  
the V-belt tension (Figure 20). Tension is proper if the belt  
bends about 10 mm when depressed strongly with finger  
between shafts. Loose or worn V-belts reduces power  
transmission efficiency, causing weak compaction and  
reduces the life of the belt itself.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—MAINTENANCE  
Replacing Hydraulic Oil  
Vibrator Oil Level Check  
1. Remove the drain plug (Figure 22) at the bottom of the oil  
tank with a 6 mm hex wrench and drain the hydraulic oil.  
CAUTION  
2. Clean the filter with light oil.  
Always clean the area around the vibrator oil level  
check hole before removing oil check plug.This will  
prevent dirt and debris from entering the system.  
3. Reinstall the drain plug to the oil tank. Apply seal tape or  
Roctite #575 to thread portion.  
4. Fill tank with hydraulic oil. (Capacity: About 2,500 cc). Use  
ShellTellus Oil #46 or equivalent.  
1. In every 100 hours of operation, with the machine positioned  
horizontally, remove vibrator oil level check plug (Figure  
21) off vibrator (19 mm wrench) and see if oil is up to filler  
port. Be sure to clean area around check hole to prevent dirt  
and dust from entering.  
5. After filling tank, temporarily install cover. Loosen bleeder  
plug located at the top of the cylinders on side of vibrator  
(Figure 23). Air remaining in the circuit will be forced out of  
the bleeder plug.  
6. Tighten the bleeder plug. Check oil level in the tank again.  
2. In every 300 hours of operation, replace oil (capacity 1,500  
cc). For draining oil through level check hole, have the  
machine inclined with a sleeper or the like placed under the  
compaction plate on opposite side.  
7. Install the cover of oil tank. Coat packing with liquid packing  
such as Threebond #1215. Use loctite #242 for mounting  
screw.  
* Use engine oil 10W-30 for this lubrication.  
Figure 21. Vibrator Oil Maintenance  
Hydraulic Oil  
Figure 22. Hydraulic Oil Maintenance  
1. Check hydraulic oil in every 100 hours of operation. With  
handle bar positioned vertically (storage position), remove  
breather plug (Figure 23) off the top of hydraulic pump and  
check for proper oil level.  
2. Replace hydraulic oil after first 200 hours and in every 1,000  
hours of operation.  
CAUTION:  
Make sure hydraulic oil i is at a normal safe operating  
level. DO NOT over fill. Over filling (excessive oil)  
will cause excess oil to blow out of breather plug.  
Figure 23. Breather Plug  
PAGE 22 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—MAINTENANCE  
CAUTION  
BATTERY MAINTENANCE  
1. Check the battery terminals periodically to ensure  
that they are in good condition.  
Wear safety glasses or face mask, protective  
clothes, and rubber gloves when working with  
battery.  
2. Use wire brush or sand paper to clean the battery  
terminals.  
3. Check battery for cracks or any other damage. If white  
pattern appears inside the battery or paste has  
accumulated at the bottom, replace the battery.  
4.. If the machine will not be in operation for a long  
period of time, store in cool dry place and check the  
battery charge level every month to maintain the  
performance of the battery.  
Troubleshooting  
BATTERY CABLE CONNECTION  
See Tables 8 (engine) and 9 (plate compactor) on proceeding  
pages for troubleshooting guide.  
1.  
2.  
3.  
Take off the battery cover by removing the M6 nuts (Figure  
24).  
When removing cable, disconnect the ground side (normally  
negative) first (Figure 24).  
When installing cable connect the ground side (normally  
negative) last.  
Figure 24. Battery Maintenance  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—TROUBLESHOOTING  
diagnosis based on the Troubleshooting (Table 8) information  
shown below. If the problem cannot be remedied, please  
leave the unit just as it is and consult our company's business  
office or service plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 8. ENGINE TROUBLESHOOTING  
SYMPTOM  
POSSIBLE PROBLEM  
Speed control lever is in "STOP" position?  
No fuel reaching injection pump?  
Defective fuel pump?  
SOLUTION  
Set speed control lever to "START" position.  
Add fuel. Check entire fuel system.  
Replace fuel pump.  
Fuel filter clogged?  
Replace fuel filter and clean tank.  
Replace or repair fuel line.  
Faulty fuel supply line?  
Engine will not start or start is  
delayed, although engine can be  
turned over.  
Check piston, cylinder and valves. Adjust or  
repair per engine repair manual.  
Compression too low?  
Repair or replace injector in accordance with  
engine repair manual.  
Fuel injector not working correctly?  
Oil pressure too low?  
Check engine oil pressure.  
Comply with cold starting instructions and  
proper oil viscosity.  
Low starting temperature limit exceeded?  
Check whether clear (not turbid) fuel emerges  
from the fuel line (detach from injection pump).  
If the fuel is turbid or separated, warm up the  
engine or drain the complete fuel supply  
Fuel separates has inadequate resistance to  
low temperatures?  
At low temperatures engine will  
not start.  
system. Refuel with winter grade diesel fuel.  
Refill engine crankcase with correct type of oil  
for winter environment.  
Engine oil too thick?  
Throttle lever in STOP position?  
Fuel filter blocked?  
Reposition throttle lever to RUN position.  
Replace fuel filter.  
Engine fires but stops soon as  
starter is switched off.  
Fuel supply blocked?  
Fuel tank empty?  
Check the entire fuel system.  
Add fuel.  
Engine stops by itself during  
normal operation.  
Fuel filter blocked?  
Replace fuel filter.  
Fuel tank empty?  
Replace fuel filter.  
Fuel filter clogged?  
Replace fuel filter.  
Low engine power, output and  
speed.  
Fuel tank venting is inadequate?  
Ensure that tank is adequately vented.  
See engine manual for corrective action.  
Speed control lever does not remain in  
selected position?  
Engine oil level too full?  
Air filter blocked?  
Correct engine oil level.  
Clean or replace air filter.  
Adjust valves per engine specification.  
See engine manual.  
Low engine power output and  
low speed, black exhaust smoke.  
Incorrect valve clearances?  
Malfunction at injector?  
PAGE 24 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB—TROUBLESHOOTING  
diagnosis based on the Troubleshooting (Table 9) information  
shown below. If the problem cannot be remedied, please  
leave the unit just as it is and consult our company's business  
office or service plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 9. TROUBLESHOOTING COMPACTOR  
SYMPTOM  
POSSIBLE CAUSE  
SOLUTION  
Adjust or replace clutch.  
Clutch slips?  
V-belt slips?  
Adjust or replace V-belt.  
Fill to correct level..  
Excessive Oil in vibrator?  
Check vibrator assembly for any worn or  
defective parts, replace any defective  
parts.  
Travel speed low and vibration weak.  
Trouble in vibrator internals?  
Aeration in hydraulic oil for for travel  
reversing syste.?  
Purge air in hydraulic oil. (Bleed plug)  
Engine speed incorrect?  
Set engine speed to correct RPM.  
Check entire travel system.  
Clean installation of reversing lever.  
Replace oil hose.  
Travel reversing system inoperative.?  
Reversing lever installation correct?  
Broken or defective oil hose?  
Aeration in hydraulic oil for for travel  
reversing syste.?  
Travels forward or backward but unable  
to switch direction.  
Purge air in hydraulic oil. (Bleed plug)  
Excessive oil in reversing system?  
Selector valve clogged with trash?  
Fill to correct level..  
Clean selector valve.  
Check piston bearing in cylinder for  
leakage at USH packing.  
Cylinder piston bearing failure?  
V-belt dis-engaged or slips?  
Clutch slips?  
Engage V-belt, adjust or replace.  
Adjust clutch, replace if necessary.  
Does not travel in forward or reverse.  
Pump input shat key or adapter key-way  
damaged?  
Replace input shatkey or adapter key-way  
Check piston bearing in cylinder for  
leakage at USH packing.  
Cylinder piston bearing failure?  
Excessive hydraulic oil?  
Reversing lever operating resistance  
great.  
Fill to correct level.  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLANATION OF CODE IN REMARKS COLUMN  
How to read the marks and remarks used in this parts  
book.  
If more than one of the same  
reference number is listed, the  
last one listed indicates newest  
(or latest) part available.  
NOTE  
Items Found In the “Remarks” Column  
Serial Numbers-Where indicated, this indicates a serial  
number range (inclusive) where a particular part is used.  
Model Number-Where indicated, this shows that the  
corresponding part is utilized only with this specific model  
number or model number variant.  
Items Found In the “Items Number” Column  
All parts with same symbol in the number column, , #,  
, belong to the same assembly or kit.  
+, %, or  
*
■
Note: If more than one of the same reference number is listed,  
the last one listed indicates newest (or latest) part available.  
The contents of this parts  
catalog are subject to change  
without notice.  
NOTE  
PAGE 26 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED SPARE PARTS  
MVH-402DSB WITH YANMAR L100EE-DEVMK1  
ENGINE  
1 to 5 Units  
Qty.  
P/N  
Description  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — DECAL PLACEMENT  
DECAL PLACEMENT  
PAGE 28 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — DECAL PLACEMENT  
DECAL PLACEMENT  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
0732004460  
920204580  
920202220  
920201580  
920206370  
920108770  
920207480  
920103670  
920203260  
920203330  
PART NAME  
QTY.  
REMARKS  
IGNITION SYSTEM DECAL  
FULLTHROTTLE DECAL  
FORWARD/REVERSE DECAL  
MULTIQUIP LOGO DECAL  
OPERATIONAL CAUTION DECAL  
MVH-402 DECAL  
1
1
1
1
1
1
1
1
1
1
NPA-458  
NPA-222  
NPA-538  
NPA-748  
SHELL OIL #46DECAL  
OIL LEVEL INDICATOR DECAL  
OIL TANK DECAL  
9
10  
HEARING PROTECTION DECAL  
NPA-333  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATING PLATE ASSY.  
VIBRATING PLATE ASSY.  
PAGE 30 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATING PLATE ASSY.  
VIBRATING PLATE ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
457112370  
953405840  
953402930  
953400270  
953405260  
939010070  
020316130  
030216400  
001221655  
030216400  
001201830  
030218460  
456210690  
001221850  
457215350  
457454090  
PART NAME  
QTY.  
REMARKS  
VIBRATING PLATE  
DRAIN PLUG M18 (H)  
COPPER PACKING 19X30X1  
PLUG 1/4X14 10L  
PACKING 1/4 (CU)  
SHOCK ABSORBER 100  
NUT M16  
1
1
1
1
1
4
4
4
4
4
8
8
WASHER, LOCK M16  
BOLT 16X75 T  
SWASHER, LOCK M16  
BOLT 18X30  
9
10  
11  
12  
21  
22  
23  
24  
WASHER, LOCK M18  
EXTENSION PLATE ................................ 2 .......... OPTION  
BOLT 18X50 T .......................................... 8 .......... OPTION  
BELT COVER GUARD .............................. 1 .......... G1185-  
CUSHION, BELT COVER GUARD ........... 1 .......... G1185-  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — BASE AND ENGINE ASSY.  
BASE AND ENGINE (YANMAR L100A) ASSY.  
PAGE 32 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — BASE AND ENGINE ASSY.  
BASE AND ENGINE (YANMAR L100A) ASSY.  
NO.  
2
5
6
8
PART NO.  
457112391  
030210250  
031110160  
001220825  
030208200  
031108160  
457113980  
457445880  
457112431  
001521056  
001521058  
070200423  
457112440  
001221025  
030210250  
031110160  
457212400  
001220835  
030208200  
031108160  
001221430  
030214350  
456437920  
001221235  
030212300  
457332401  
457335980  
001220615  
031106100  
030206150  
456449950  
456449960  
001220825  
031108160  
022710809  
914410002  
001221040  
457113970  
457335990  
951400110  
952400690  
001220851  
030208200  
457115380  
457440140  
PART NAME  
QTY.  
1
4
4
4
4
4
1
1
1
2
2
2
1
4
4
4
1
4
4
4
4
4
1
1
1
1
2
4
4
4
1
1
3
3
3
1
4
1
1
1
1
1
1
1
1
REMARKS  
BASE  
WASHER, LOCK M10  
WASHER, FLAT M10  
BOLT 8X25 T  
WASHER, LOCK M8  
WASHER, FLAT M8  
BELT COVER (OUT)  
DUST PACKING  
10  
11  
13  
14  
15  
16  
17  
23  
24  
25  
26  
27  
28  
29  
30  
31  
33  
34  
35  
36  
37  
39  
44  
45  
46  
47  
51  
52  
53  
54  
55  
101  
102  
103  
105  
106  
107  
108  
109  
110  
111  
DUST COVER  
SOCKET HEAD BOLT 10X80 T  
SOCKET HEAD BOLT 10X90 T  
V-BELT B- 42 GREEN/HDPF542  
BELT COVER ( LOWER-IN)  
BOLT 10X25 T  
WASHER, LOCK M10  
WASHER, FLAT M10  
BELT COVER ( LOWER- OUT)  
BOLT 8X35 T  
WASHER, LOCK M8  
WASHER, FLAT M8  
BOLT 14X30 T  
WASHER, LOCK M14  
WASHER, PULLEY  
BOLT 12X35 T  
WASHER, LOCK M12  
PULLEY B2-125 /131- 68  
HOLDER, DUST COVER  
BOLT 6X15 T  
WASHER, FLAT M6  
WASHER, LOCK M6  
PLATE, COVER  
RUBBER COVER  
BOLT 8X25 T  
WASHER, FLAT M8  
NYLON NUT M8  
ENGINE AY L100A  
BOLT 10X40 T  
BELT COVER (IN) L100  
CLUTCH AY B2-164-25 W/FAN  
KEY 7X7X35  
WASHER 9X35X4.5  
BOLT 8X55 T  
WASHER, LOCK M8  
GUARD FRAME (L100)  
WIRE CP 110L  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATOR ASSY.  
VIBRATOR ASSY.  
PAGE 34 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATOR ASSY.  
VIBRATOR ASSY.  
NO.  
1
2
3
4
5
6
7
7
PART NO.  
457112460  
001221470  
001221450  
030214350  
047920060  
457212410  
457445830  
457445831  
951405370  
456327150  
080200550  
060105030  
951404970  
457332420  
009120301  
456337670  
009120302  
456337380  
456010010  
456327120  
040006911  
455435020  
456451280  
080100300  
042506000  
PART NAME  
VIBRATING CASE  
BOLT 14X150 T  
QTY.  
1
6
4
10  
4
1
1
1
1
1
2
1
1
4
2
1
2
1
1
1
2
2
1
1
2
REMARKS  
BOLT 14X50 T  
WASHER, LOCK M14  
ROLLER BEARING NJ310MC4  
ROTARY SHAFT, DRIVE  
ADAPTER, PUMP  
ADAPTER, PUMP (30L)  
KEY 15X10X39 RR  
GEAR, DRIVE  
STOP RING S-55  
OIL SEAL SB- 50729  
KEY 12X8X30 R  
ECCENTRIC ROTOR  
SOCKET HEAD BOLT 16X40T  
ROTARY SHAFT, DRIVEN  
SOCKET HEAD BOLT 16X30T  
PISTON ROD  
KNOCK PIN 10X70  
GEAR, DRIVEN  
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
24  
25  
BEARING 6911  
COLLAR 17X30X3  
SPRING 3.2-26.3-102L  
STOP RING R- 30  
BEARING 6000ZZSG  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATOR ASSY.  
VIBRATOR ASSY.  
PAGE 36 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB —VIBRATOR ASSY. (CONTINUED)  
VIBRATOR ASSY.  
NO.  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
PART NO.  
080200100  
455435051  
455010070  
080100260  
456327130  
456210646  
954405550  
050101050  
001221025  
030210250  
001220812  
953404600  
455010020  
031110160  
457332430  
457010010  
457445840  
457212420  
001221035  
001221030  
952405540  
030210250  
954010140  
954001780  
952405470  
PART NAME  
STOP RING S-10  
PISTON,22.4D  
PACKING USH- 22.4X30X5  
STOP RING R-26  
BEARING COVER  
CYLINDER (R)  
CLAMP 15R  
O-RING G-105  
BOLT 10X25 T  
WASHER, LOCK M10  
BOLT 8X12 T  
COPPER PACKING 8X16X2  
ELBOW 45 15-0404  
WASHER, FLAT M10  
FLANGE, PUMP  
PUMP FBL  
BRACKET, CLAMP  
PUMP COVER  
BOLT 10X35 T  
BOLT 10X30 T  
WASHER 10.5- 22- 3  
WASHER, LOCK M10  
ELBOW 90 UES90G02G02  
ELBOW 45 PF3/8- PF1/4  
SHIM 90X110X0.5  
QTY.  
1
1
1
1
1
1
1
3
7
12  
1
1
1
7
1
1
1
1
2
5
2
2
1
1
2
REMARKS  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — HYDRAULIC SYSTEM ASSY.  
HYDRAULIC SYSTEM ASSY.  
PAGE 38 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — HYDRAULIC SYSTEM ASSY.  
HYDRAULIC SYSTEM ASSY.  
NO.  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
79  
80  
81  
82  
83  
84  
85  
PART NO.  
456337880  
001220615  
030206150  
031106100  
457446180  
457446190  
457451750  
457446210  
955404271  
954403060  
954403070  
001220612  
030206150  
506010070  
954001160  
457112470  
001221030  
030210250  
031110160  
505015380  
457332440  
457445870  
001220820  
030208200  
031108160  
456449280  
457445861  
506010060  
457448680  
953400020  
457448380  
457451740  
551010630  
953402941  
PART NAME  
SELECTOR VALVE (DETENT)  
BOLT 6X15 T  
WASHER, LOCK M6  
WASHER, FLAT M6  
OIL HOSE 137OL  
OIL HOSE 1150L  
OIL HOSE IB105- L820  
OIL HOSE 1100L  
SPIRAL TUBE, SR15- 850L  
CLAMP HC- 40  
CLAMP SPACER HC- 40  
BOLT 6X12 T  
WASHER, LOCK M6  
CLAMP TC- 150  
ELBOW 90 PT1/4- PF1/4  
OIL TANK  
QTY.  
1
4
4
4
1
1
1
1
2
1
1
2
2
1
4
1
3
3
3
1
1
1
2
2
2
1
1
2
1
2
1
1
1
3
REMARKS  
BOLT 10X30 T  
WASHER, LOCK M10  
WASHER, FLAT M10  
PLUG PT1/4  
COVER, OIL TANK  
PACKING, OIL TANK  
BOLT 8X20 T  
WASHER, LOCK M8  
WASHER, FLAT M8  
FILTER, OIL TANK  
JOINT 80L  
CLAMP TC- 350  
BREATHING PLUG  
PACKING 19302  
BREATHER CAP  
BREATHER JOINT  
ELBOW PT1/4- PF3/8 1034- 06  
COPPER PACKING 13.5X21X1  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — CONTROL ASSY.  
CONTROL ASSY.  
PAGE 40 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — CONTROL ASSY.  
CONTROL ASSY.  
NO.  
1
2
3
4
5
7
8
9
PART NO.  
456336410  
456336420  
001221235  
030212300  
031112230  
456336400  
456449940  
456449930  
001221681  
032124400  
025406016  
031116260  
020316130  
020416100  
001220640  
020306050  
455434950  
455010030  
939010060  
020410060  
020412070  
022411635  
954404230  
001220620  
030206150  
031106100  
020306050  
001220825  
030208200  
031108160  
953401580  
501402870  
501402880  
PART NAME  
QTY.  
1
1
4
4
4
2
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
1
1
1
REMARK  
HANDLE BRACKET (L)  
HANDLE BRACKET (R)  
BOLT 12X35 T  
WASHER, LOCK M12  
WASHER, FLAT M12  
RUBBER COUPLING  
SHOCK ABSORBER  
RUBBER PLATE  
BOLT 16X250 T  
CONICAL SPRING WASHER M24  
SPRING PIN 6X16  
WASHER, FLAT M16  
NUT M16  
NUT M16, H=10  
BOLT 6X40 T  
NUT M6  
SPINDLE  
KNOB  
SHOCK ABSORBER 60  
NUT, M10 H=6  
NUT, M12 H=7  
WING NUT M16  
CLAMP SA120- 18  
BOLT 6X20 T  
WASHER, LOCK M6  
WASHER, FLAT M6  
NUT M6  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
BOLT 8X25 T  
WASHER, LOCK M8  
WASHER, FLAT M8  
PLUG  
HANDLE STOPPER /MDR  
SPRING/ HANDLE (1.4X18X44)  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — CONTROL ASSY.  
CONTROL ASSY.  
PAGE 42 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — CONTROL ASSY. (CONTINUED)  
CONTROL ASSY.  
NO.  
36  
37  
38  
39  
40  
41  
43  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
61  
62  
62  
63  
64  
65  
66  
67  
68  
69  
71  
72  
73  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
PART NO.  
959403460  
020410060  
456449980  
953405260  
031110160  
456450760  
456214360  
456214720  
001220820  
030208200  
031108160  
001220815  
033910020  
457445910  
001220850  
020308060  
031108160  
001220630  
020306050  
031106100  
456114840  
456214220  
456214222  
456214210  
032112220  
456451400  
456337400  
608010090  
457332480  
020412070  
959403840  
456337690  
456451290  
456452070  
951401431  
031112230  
020412070  
032112220  
953402930  
509010130  
959021624  
956100028  
001820830  
020308060  
PART NAME  
BALL GRIP 32D- M10  
NUT M10, H=6  
RUBBER PACKING 9D- 20D- 5T  
PACKING 1/4 (CU)  
WASHER, FLAT M10  
JOINT  
LEVER BRACKET .................................... 1 ......... UP TO S/N G1538  
LEVER BRACKET .................................... 1 ......... S/N G1539~  
QTY.  
REMARKS  
1
1
1
1
1
1
BOLT 8X20 T  
1
3
3
2
2
1
1
2
2
1
2
2
1
1
1
1
2
2
1
2
1
3
1
1
WASHER, LOCK M8  
WASHER, FLAT M8  
BOLT 8X15 T  
THRUST WASHER 20 - 36 - 1.5T  
CLEVIS  
BOLT 8X50 T  
NUT M8  
WASHER, FLAT M8  
BOLT 6X30  
NUT M6  
WASHER, FLAT M6  
HANDLE  
HANDLE GRIP  
HANDLE GRIP  
VALVE BRACKET  
CONICAL SPRING WASJER M12  
WASHER 12.2-27-0.6T  
TRAVEL LEVER  
BUSHING MB2015DU  
GRIP, TRAVEL LEVER  
NUT M12  
BAR GRIP ID 12MM  
THROTTLE LEVER  
WIRE GUIDE............................................. 1 ......... UP TO S/N G1538  
WIRE GUIDE............................................. 1 ......... S/N G1539~  
KEY 5X5X8  
WASHER, FLAT M12  
NUT M12  
CONICAL SPRING WASHER M12  
COPPER PACKING 19X30 X1  
BUSHING MB1825DU  
TUBE 8-13-150L  
1
2
2
2
2
1
1
1
THROTTLEWIRE 710-1980  
BOLT 8X30 T WHOLE THREAD ................ 1 ......... S/N G1539~  
NUT M8 ..................................................... 1 ......... S/N G1539~  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — BATTERY ASSY.  
BATTERY ASSY.  
PAGE 44 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-402DSB — BATTERY ASSY.  
BATTERY ASSY.  
NO.  
1
2
4
5
6
7
8
9
10  
11  
12  
13  
17  
18  
19  
21  
22  
23  
24  
26  
28  
29  
30  
PART NO.  
456438080  
456438090  
456447590  
456447600  
959403830  
020310080  
955010020  
955404130  
955300220  
955404140  
955300210  
456210660  
457445890  
022710809  
031108160  
001220815  
030208200  
457333310  
456439070  
959406070  
454010020  
456447960  
456451530  
PART NAME  
QTY.  
1
1
1
2
2
2
1
1
1
1
1
1
2
2
2
1
REMARKS  
BATTERY CORD (-) 370L  
BATTERY CORD (+) 200L  
RUBBER PLATE (E) 28X240X5  
RUBBER PLATE 50X240X10  
EYE BOLT M10X18  
NUT M10  
BATTERY 46B24L  
BATTERY TERMINAL - , BE511  
TERMINAL COVER (BLACK)  
BATTERY TERMINAL +, BE513  
TERMINAL COVER  
BATTERY COVER  
BATTERY BOLT  
NYLON NUT M8  
WASHER, FLAT M8  
BOLT 8X15 T  
WASHER,FLAT M8  
KEY SWITCH  
WIRE CP  
RUBBER PLATE 3-50-60  
CLAMPTC-100  
1
1
1
5
2
1
LAMP AY, CTL-904  
READ CORD, L90..................................... 1 .......... L100A  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CYLINDER BLOCK ASSY.  
CYLINDER BLOCK ASSY.  
PAGE 46 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CYLINDER BLOCK ASSY.  
CYLINDER BLOCK ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
71497001560  
11435001700  
26106100122  
10502501220  
11465001230  
11465001240  
11465001250  
11465001260  
11465101330  
11425001800  
11465001380  
11427001600  
26226060182  
26226060222  
26366060002  
11465001412  
11466001471  
11465002100  
11425035150  
26106080352  
10542501690  
11469901760  
11429901950  
22190160002  
11429902030  
11465002150  
11425001830  
11425001841  
24162152112  
24423355008  
22423355008  
26106080122  
11465002200  
11465002210  
22312040080  
18327908350  
22190160002  
16011001870  
12125239450  
71465651130  
BLOCK ASSY. CYLINDER ........................... 1 ................... INCLUDES ITEMS W/  
*
6
*
7
*
8
COVER, STARTER  
BOLT M10X 12 PLATED  
NUT 10  
1
2
2
2
2
2
4
1
1
1
2
1
2
3
1
9
STUD, CYLINDER HEAD  
STUD, CYLINDER HEAD  
NUT 10  
10  
11  
12  
13  
19  
25  
26  
27  
28  
29  
30  
31  
34+  
36  
37  
38  
39  
41#  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
56  
57  
58  
59  
60  
WASHER  
GASKET, CYLINDER HEAD CMP  
SHIM SET  
O-RING  
PARALLEL PIN 8 X 12  
STUD M 6 X 18 PLATED  
STUD M 6 X 22 PLATED  
NUT M 6  
GASKET CRANKCASE  
COVER D, CRANKCASE ............................. 1 ................... INCLUDES ITEMS W/+  
BEARING, MAIN  
PIPE, L.O. INLET  
BOLT M 8 X 35 PLATED  
PLUG M16  
1
1
16  
2
CAP, W/LUB.OIL GAUGE............................. 1 ................... INCLUDES ITEMS W/#  
O-RING  
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
SEAL WASHER 16S  
RETAINER  
BALL BEARING  
COVER, INSPEC.WINDOW  
GASKET  
NEEDLE BEARING  
SEAL, OIL  
SEAL, OIL  
BOLT M 8 X 12 PLATED  
MAIN BEARING US = 0.25  
MAIN BEARING US = 0.50  
PIN 4 X 8 STRAIGHT  
NIPPLE, DRAIN  
SEAL WASHER 16S  
PLUG, RUBBER W/SCREW  
SENDER, OIL PRESSURE  
PUMP ASSY., FUEL INJECTION  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CYLINDER HEAD AND COVER ASSY.  
CYLINDER HEAD AND COVER ASSY.  
PAGE 48 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CYLINDER HEAD AND COVER ASSY.  
CYLINDER HEAD AND COVER ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
11465111020  
11465111100  
11465111110  
11465011121  
11962011180  
11465111250  
11465111260  
11465111650  
11425011240  
26856060002  
11465111660  
11425011240  
26856060002  
22242000150  
11465011340  
10421111370  
11477111461  
11477111470  
11465011600  
27310070000  
26106060702  
11425011901  
22351040008  
26106080552  
26226060552  
26366060002  
11465111310  
11465111950  
11425003591  
11425003640  
22312030160  
CYLINDER HEAD  
VALVE, SUCTION  
VALVE, EXHAUST  
SPRING, VALVE  
RETAINER, SPRING  
1
1
1
2
2
6
7
8
9
10  
11  
SUPPORT CMP, ARM .............................. 1 ................. INCLUDES ITEMS W/  
*
SUPPORT, ROCKER ARM  
ARM ASSY. INTAKE  
SCREW, VALVE ADJUST  
LOCK NUT 6  
ARM ASSY., EXHAUST  
SCREW, VALVE ADJUST  
LOCK NUT 6  
CIRCLIP 15  
SEAL, VALVE STEM  
CAP, VALVE  
GASKET, NOZZLE  
SPACER, NOZZLE  
WASHER  
1
1
1
1
1
1
1
2
2
2
1
1
2
4
3
1
1
2
2
2
1
*
12  
14  
15  
16  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
*
*
*
*
*
COTTER 7  
BOLT M 6 X 70 PLATED  
RETAINER  
SPRING PIN 4 X 8  
BOLT M 8 X 55 PLATED  
STUD M 6 X 55 PLATED  
NUT M 6  
GASKET, BONNET  
COVER ASSY. HEAD................................ 1 ................. INCLUDES ITEMS W/#  
36#  
39#  
41#  
SHAFT ASSY., DECOMP.  
SPRING  
PARALLEL PIN 3 X 16  
1
1
1
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — MUFFLER ASSY.  
MUFFLER ASSY.  
PAGE 50 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — MUFFLER ASSY.  
MUFFLER ASSY.  
NO  
17  
18  
19  
20  
PART NO  
PART NAME  
QTY.  
REMARKS  
11465013201  
11467413551  
11467413511  
18338213700  
11497013710  
11497313710  
16026001580  
26106080162  
26216080182  
26366080002  
11498513800  
26367060002  
26554060162  
GASKET, NON-ASB. .................................1 ................. INCLUDES ITEMS W/  
*
MUFFLER ASSY.  
MUFFLER  
COVER, MUFFLER  
COVER, MUFFLER  
COVER, MUFFLER  
BOLT, M 6 X 6  
BOLT, M 8 X 16 PLATED  
STUD, M 8 X 18 PLATED  
NUT, M 8  
1
1
1
*
21  
22  
23  
29  
31  
32  
33  
1
*
*
*
*
1
10  
2
2
2
DEFLECTOR, EXHAUST ...........................1 ................. INCLUDES ITEMS W/#  
NUT, 6  
SCREW, M 6 X 16  
*
35 #  
*
1
1
36 #  
*
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
PAGE 52 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
11465012211  
71465012560  
11465012520  
11465012530  
11425212560  
11465012590  
11425212550  
11425012300  
11469912020  
11465012301  
26106060252  
26226060142  
26226060752  
GASKET, AIR CLEANER  
1
2
CLEANER ASSY. AIR ............................... 1 ................. INCLUDES ITEMS W/  
*
4
COVER, AIR CLEANER  
CASE, AIR CLEANER  
WASHER M 8, SEAL  
ELEMENT W/PRE-FILTER  
WING, NUT M 8  
1
1
1
1
1
3
1
1
3
1
2
*
5
*
6
*
7
*
10  
*
11  
12  
13  
14  
15  
16  
U- NUT  
PIPE, AIR INTAKE  
GASKET, AIR INTAKE  
BOLT M 6 X 25 PLATED  
STUD M 6 X 14 PLATED  
STUD M 6 X 75  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
CRANKSHAFT, PISTON AND CAMSHAFT ASSY.  
PAGE 54 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
CRANKSHAFT, PISTON AND CAMSHAFT ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
71466014100  
11465014200  
11477114260  
11465014401  
71465421730  
12271001220  
11465021551  
11466221593  
11466221601  
22512050140  
71465222720  
71497022500  
11469922300  
12979222400  
71465023100  
12406023100  
10530023200  
71465023600  
71497028100  
24101062034  
16031014550  
22512070360  
26106080202  
71465023610  
71465023620  
24101063034  
11465002100  
11465002150  
24162152112  
CAMSHAFT ASSY., D  
TAPPET  
1
2
1
2
1
1
1
6
7
8
TAPPET, F.O.  
ROD, PUSH  
12  
20  
21  
22  
25 #  
26  
27  
CRANKSHAFT ASSY.  
NUT, M18  
WASHER, FLYWHEEL  
FLYWHEEL, DEJ., W/GEAR ..................... 1 ................. INCLUDES ITEMS W/ #  
GEAR, RING  
KEY, 5 X 14  
1
1
PISTON, W/RINGS ................................... 1 ................. INCLUDES ITEMS W/  
*
29  
RING SET, PISTON  
PIN, PISTON D=23  
CIRCLIP 23  
1
1
2
*
35  
36  
37  
ROD ASSY., CONNECTING ..................... 1 ................. INCLUDES ITEMS W/%  
BUSH, PISTON PIN  
BOLT, ROD  
BEARING, CRANKPIN  
SHAFT ASSY., BALANCER  
BALL BEARING  
WASHER  
KEY 7 X 36  
40%  
41%  
42%  
44  
1
2
1
1
1
1
1
1
1
1
1
1
1
1
49  
50  
51  
52  
BOLT M 8 X 20 PLATED  
BEARING, PIN U.S=0.25  
BEARING, PIN U.S=0.50  
BALL BEARING  
53  
55  
57  
54  
BEARING, MAIN  
56  
BALL BEARING  
58  
NEEDLE BEARING  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — LUB. OILPUMP AND GOVERNOR ASSY.  
LUB. OIL PUMP AND GOVERNOR ASSY.  
PAGE 56 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — LUB. OILPUMP AND GOVERNOR ASSY.  
LUB. OIL PUMP AND GOVERNOR ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
11465032010  
11425032070  
10333832570  
22312030160  
26476060142  
11425035110  
11425035070  
24341000224  
26106060162  
71465061500  
22322030200  
22322030200  
71468561700  
11477061520  
11477061600  
11477061610  
11477061190  
11497066010  
11425066200  
11465066750  
26776100002  
13521061090  
22451060000  
11425266051  
18336066110  
11425266252  
11425066440  
10522566990  
26106060202  
26757060002  
11465166150  
11477161800  
11477161820  
11477161900  
11477161930  
PUMP ASSY. LUB. OIL  
COVER, LUB. OIL PUMP  
O-RING  
1
1
1
1
3
6
7
8
PARALLEL PIN 3 X 16  
BOLT, M 6 X 14, TAPPING  
STRAINER, LUB. OIL ............................. 1.................... INCLUDES ITEMS W/  
9
10  
11  
*
STRAINER, LUB. OIL  
O-RING 1A S-22.4  
BOLT M 6 X 16 PLATED  
LEVER ASSY. GOVERNOR  
TAPER PIN 3 X 20  
TAPER PIN 3 X 20  
GOVERNOR ASSY.  
BEARING, NEEDLE  
SEAL, OIL  
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
12  
13  
14  
19  
20  
21  
27  
28  
29  
31  
32  
33  
34  
39  
40  
41  
56  
58  
59  
60  
61  
62  
64  
65  
66  
67  
68  
69  
*
WASHER,THRUST  
WASHER  
SPRING, REGULATOR  
SPRING, RETURN  
TORQUE SPRING ASSY.  
LOCK NUT M10 PLATED  
LEAD  
WIRE 0.6  
HANDLE, REGULATOR  
BRACKET, REGULATOR  
SPRING, RETURN  
BOLT, ADJUSTING  
SCREW  
BOLT M 6 X 20 PLATED  
NUT 6  
BOLT  
WASHER  
PLATE  
PROCTECTOR  
NUT  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — COOLING AND STARTING DEVICE ASSY.  
COOLING AND STARTING DEVICE ASSY.  
PAGE 58 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — COOLING AND STARTING DEVICE ASSY.  
COOLING AND STARTING DEVICE ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
11465045201  
11435045320  
11435045340  
18372055210  
26106060202  
11466845102  
11425045301  
11425045310  
11465045330  
11437045351  
11466076052  
11466076251  
COVER  
1
1
1
1
1
1
4
4
1
4
2
RUBBER, SEAL  
COLLAR  
GROMMET  
BOLT M 6 X 20 PLATED  
CASE, FAN SILVER 17  
RUBBER, CUSHION  
COLLAR  
SEAL, FAN CASE  
BOLT, FAN CASE  
3
4
5
6
7
8
9
10  
11  
12  
RECOIL STARTER D ASSY...................1.................... INCLUDES ITEMS W/  
*
RECOIL ASSY. .......................................1.................... INCLUDES ITEMS W/ +  
*
13 + 11488076520  
REEL, RECOIL  
1
1
2
1
1
1
2
1
1
1
1
4
3
1
*
14 + 11466076531  
CASE D, W/NO LABEL  
RATCHET  
*
15 + 11487076530  
*
16 + 11487076540  
SPRING, SPRIAL  
GUIDE, RATCHET  
SPRING, FRICTION  
SPRING, RETURN  
SET SCREW  
*
17 + 11487076550  
*
18 + 11487076560  
*
19 + 11487076570  
*
20 + 11487076580  
*
22 + 11487076620  
KNOB, STARTER  
ROPE, RECOIL STARTER  
PULLEY, STARTER  
BOLT M 6 X 8 PLATED  
BOLT M 6 X 12 PLATED  
FLYWHEEL W/GEAR  
*
23 + 11465076631  
*
24  
25  
26  
28  
11466076592  
26106060082  
26106060122  
11466221593  
*
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — FUEL INJECTION PUMP ASSY.  
FUEL INJECTION PUMP ASSY.  
PAGE 60 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — FUEL INJECTION PUMP ASSY.  
FUEL INJECTION PUMP ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
71465651130  
10554651020  
11425051080  
11497051100  
11425051160  
11465051300  
10554651330  
11425051340  
12455051350  
11425051600  
11425051640  
11425051650  
22351020006  
22351030008  
71465653101  
11477111461  
11465153000  
11477111470  
11959353080  
11425053120  
11959353130  
11477553140  
11477553210  
11487553100  
PUMP ASSY., F. INJECT. .......................1.................... INCLUDES ITEMS W/  
*
3
GASKET  
PLATE  
BODY, F.I. PUMP  
SPRING  
VALVE ASSY., DELIVERY  
SPRING, DELIVERY VALVE  
HOLDER, F. I. P. DELIVERY  
GASKET, DELIVERY  
LEVER ASSY., CONTROL  
SEAT A, SPRING  
SEAT B, SPRING  
SPRING PIN 2 X 6  
SPRING PIN 3 X 8  
1
1
1
1
1
1
1
2
1
1
1
2
2
*
4
*
5
*
10  
*
11  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
*
*
*
*
*
*
*
*
*
VALVE ASSY., F. INJECT ....................... 1.................... INCLUDES ITEMS W/+  
GASKET, NOZZLE  
NOZZLE  
1
1
1
1
1
1
1
2
24+  
25+  
26+  
27+  
28+  
29+  
30+  
31+  
SPACER, NOZZLE  
NUT, NOZZLE CASE  
SPRING, NOZZLE  
RETAINER  
SPACER, VALVE STOP  
PIN  
HOLDER ASSY. ...................................... 1.................... INCLUDES ITEMS W/%  
PIN, SPRING  
SHIM PACK  
SHIM SET  
34+% 11425053331  
1
1
1
35+  
36  
11425053400  
11425001800  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — FUELTANK AND FUEL LINE ASSY.  
FUEL TANK AND FUEL PIPE ASSY.  
PAGE 62 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — FUELTANK AND FUEL LINE ASSY.  
FUEL TANK AND FUEL PIPE ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
71465055130  
11428855041  
11428855081  
11425055100  
11465055150  
10385455220  
23414080000  
10530055080  
11425055201  
11425055121  
11425055130  
11429955210  
11469955230  
11425055300  
24341000150  
11465159802  
11456055810  
11465059850  
22117080000  
26106080452  
26366060002  
26476060142  
10699044660  
11426859061  
11465259300  
12472259050  
11465059060  
11465259310  
12175059890  
71465651130  
71465653101  
TANK ASSY., FUEL ................................1.................... INCLUDES ITEMS W/  
*
3
CAP ASSY., FUEL TANK ........................1.................... INCLUDES ITEMS W/ +  
*
5 +  
*
VALVE  
1
1
1
2
1
1
4
6
FILTER, FUEL  
PIPE, GAUGE  
CLAMP  
*
7
8
9
GASKET 8, ROUND  
PLUG, DRAIN  
DAMPER, FUEL TANK  
*
10  
*
11  
12  
*
FILTER, FUEL OIL ..................................1.................... INCLUDES ITEMS W/#  
13#  
GASKET  
STAY  
STAY B, FUEL TANK  
COCK ASSY., FUEL  
1
1
1
1
14  
15  
16  
17%  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
O-RING 1A S-15.0...................................1.................... INCLUDES ITEMS W/%  
PIPE, FUEL INJECTION  
BOLT, LIFTING  
1
1
1
1
1
2
2
2
1
BRACKET, PIPE  
WASHER 8  
BOLT M 8 X 45 PLATED  
NUT M 6  
BOLT M 6 X 14 TAPPING  
CLIP, HOSE  
PIPE, FUEL OIL  
■
PIPE, FUEL RETURN .............................1.................... INCLUDES ITEMS W/  
■
28  
CLAMP 9  
2
1
1
1
1
1
■
29  
PIPE, FUEL RETURN  
TUBE, PROTECT  
■
30  
■
31  
CLAMP 140  
32  
33  
PUMP ASSY., FUEL INJECTION  
VALVE ASSY., FUEL INJECTION  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — STARTING MOTOR AND DYNAMO ASSY.  
STARTING MOTOR AND DYNAMO ASSY.  
PAGE 64 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 — STARTING MOTOR AND DYNAMO ASSY.  
STARTING MOTOR AND DYNAMO ASSY.  
NO  
PART NO  
PART NAME  
QTY.  
REMARKS  
1
11436277011  
11438177110  
X2114811000  
X2114715500  
11438177130  
11438177140  
11437177160  
11437179040  
11437179050  
STARTER, S114-651A ............................1.................... INCLUDES ITEMS W/  
*
2
ARMATURE  
1
1
1
1
1
*
3
WASHER KIT, THRUST  
STOPPER SET, PINION  
COIL ASSY., FIELD  
COVER, REAR  
*
4
*
5
*
6
*
7
HOLDER ASSY., BRUSH ........................1.................... INCLUDES ITEMS W/ +  
*
8 +  
*
BRUSH, -  
BRUSH, +  
SPRING, BRUSH  
PINION ASSY.  
1
1
4
1
1
1
1
1
2
2
1
2
9 +  
*
10 + 11437179060  
*
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
X211485016  
11438177151  
11437177170  
11437177180  
12429877020  
12419577770  
11437179070  
X2114274200  
26106100302  
11435178251  
11435178751  
11435178761  
16071078710  
26106060122  
26106060202  
26577060142  
16097077350  
26106060122  
18335607740  
10519878570  
26716080002  
16067178200  
11468578560  
*
*
*
*
*
*
*
HOUSING ASSY. GEAR  
COVER KIT, DUST  
SHIFT LEVER KIT  
SWITCH, MAGNET  
BOLT, THROUGH  
BOLT M 6 X 37  
COVER, TERMINAL  
BOLT M 10 X 30 PLATED  
DYNAMO ASSY. .....................................1.................... INCLUDES ITEMS W/ #  
21#  
22#  
23  
24  
25  
26  
27  
28  
29  
36  
41  
42  
43  
STATOR ASSY.  
WHEEL, DYNAMO  
CLAMP, CORD  
1
1
1
1
3
3
1
2
1
1
1
1
1
BOLT M 6 X 12 PLATED  
BOLT M 6 X 20 PLATED  
SCREW M 6 X 14  
RECTIFIER  
BOLT M 6 X 12 PLATED  
WIRE, LEAD  
HARNESS C, WIRE  
NUT M 8  
WIRE, LEAD  
WIRE HARNESS  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 —TOOL, LABEL AND GASKET SET ASSY.  
TOOL, LABEL AND GASKET SET ASSY.  
PAGE 66 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L100EE-DEVMK1 —TOOL, LABEL AND GASKET SET ASSY.  
TOOL, LABEL AND GASKET SET ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARKS  
11436277011  
11425007090  
11425007111  
11426807240  
11426107350  
71465192620  
11465101330  
11465001380  
11465001412  
11429901950  
11425001841  
22190160002  
11465011340  
11477111461  
11465111310  
11465012301  
11465012211  
11465013201  
10333832570  
24341000224  
24311000125  
23414080000  
STARTER, S114-651A  
LABEL, AIR COOLED  
LABEL, YANMAR  
LABEL, CAUTION  
LABEL  
1
1
1
1
1
4
5
6
7
26  
27  
GASKET SET ......................................... 1.................... INCLUDES ITEMS W/  
*
GASKET, CYLINDER HEAD CMP.  
O-RING  
1
1
1
1
1
4
2
1
1
1
1
2
1
1
1
1
*
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
GASKET, CRANKCASE  
O-RING  
GASKET  
SEAL WASHER 16S  
SEAL, VALVE STEM  
GASKET, NOZZLE  
GASKET, BONNET  
GASKET, AIR INTAKE  
GASKET, AIR CLEANER  
GASKET, NON-ASB  
O-RING  
O-RING 1A S-22.4  
O-RING 1A P-12.5  
GASKET 8, ROUND  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Effective:October 1, 2002  
TERMS AND CONDITIONS OF SALE — PARTS  
PAYMENTTERMS  
5. Parts must be in new and resalable  
condition,intheoriginalMultiquippack-  
age (if any), and with Multiquip part  
numbersclearlymarked.  
Rebatesforpricedeclinesandaddedcharges  
for price increases will not be made for stock  
onhandatthetimeofanypricechange.  
Terms of payment for parts are net 10 days.  
FREIGHTPOLICY  
Multiquip reserves the right to quote and sell  
directtoGovernmentagencies,andtoOriginal  
Equipment Manufacturer accounts who use  
our products as integral parts of their own  
products.  
All parts orders will be shipped collect or  
prepaidwiththechargesaddedtotheinvoice.  
All shipments are F.O.B. point of origin.  
Multiquip’sresponsibilityceaseswhenasigned  
manifest has been obtained from the carrier,  
andanyclaimforshortageordamagemustbe  
settledbetweentheconsigneeandthecarrier.  
6. Thefollowingitemsarenotreturnable:  
a. Obsolete parts.(If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
SPECIALEXPEDITINGSERVICE  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
priortothereturndate.  
A$35.00surchargewillbeaddedtotheinvoice  
forspecialhandlingincludingbusshipments,  
insuredparcelpostorincaseswhereMultiquip  
mustpersonallydeliverthepartstothecarrier.  
MINIMUMORDER  
TheminimumchargeforordersfromMultiquip  
is $15.00 net. Customers will be asked for  
instructionsregardinghandlingofordersnot  
meetingthisrequirement.  
LIMITATIONSOFSELLER’SLIABILITY  
c. Anylineitemwithanextendeddealer  
netpriceoflessthan$5.00.  
Multiquip shall not be liable here under for  
damagesinexcessofthepurchasepriceofthe  
itemwithrespecttowhichdamagesareclaimed,  
andinnoeventshallMultiquipbeliableforloss  
of profit or good will or for any other special,  
consequentialorincidentaldamages.  
RETURNEDGOODSPOLICY  
d. Special order items.  
Returnshipmentswillbeacceptedandcredit  
willbeallowed,subjecttothefollowingprovi-  
sions:  
e. Electricalcomponents.  
f. Paint,chemicals,andlubricants.  
g. Decalsandpaperproducts.  
h. Itemspurchasedinkits.  
1. AReturnedMaterialAuthorizationmust  
be approved by Multiquip prior to ship-  
ment.  
LIMITATIONOFWARRANTIES  
Nowarranties,expressorimplied,aremadein  
connectionwiththesaleofpartsortradeacces-  
soriesnorastoanyenginenotmanufactured  
byMultiquip.Suchwarrantiesmadeinconnec-  
tion with the sale of new, complete units are  
madeexclusivelybyastatementofwarranty  
packagedwithsuchunits,andMultiquipnei-  
ther assumes not authorizes any person to  
assume for it any other obligation or liability  
whatever in connection with the sale of its  
products.Apartfromsuchwrittenstatementof  
warranty, there are no warranties, express,  
impliedorstatutory,whichextendbeyondthe  
descriptionoftheproductsonthefacehereof.  
7. The sender will be notified of any  
materialreceivedthatisnotacceptable.  
2. ToobtainaReturnMaterialAuthorization,  
alistmustbeprovidedtoMultiquipParts  
Salesthatdefinesitemnumbers,quanti-  
ties, and descriptions of the items to be  
returned.  
8. Such material will be held for five  
workingdaysfromnotification,pending  
instructions. If a reply is not received  
within five days, the material will be  
returnedtothesenderathisexpense.  
a. Thepartsnumbersanddescriptions  
must match the current parts price  
list.  
9. Creditonreturnedpartswillbeissuedat  
dealer net price at time of the original  
purchase,lessa15%restockingcharge.  
b. The list must be typed or computer  
generated.  
10. Incaseswhereanitemisaccepted,for  
which the original purchase document  
cannotbedetermined,thepricewillbe  
basedonthelistpricethatwaseffective  
twelvemonthspriortotheRMAdate.  
c. The list must state the reason(s) for  
thereturn.  
d. The list must reference the sales  
order(s)orinvoice(s)underwhichthe  
itemswereoriginallypurchased.  
11. Credit issued will be applied to future  
purchasesonly.  
e. The list must include the name and  
phonenumberofthepersonrequest-  
ingtheRMA.  
PRICINGANDREBATES  
Prices are subject to change without prior  
notice.Pricechangesareeffectiveonaspe-  
cific date and all orders received on or after  
3. AcopyoftheReturnMaterialAuthoriza-  
tionmustaccompanythereturnshipment.  
4. Freight is at the sender’s expense. All that date will be billed at the revised price.  
partsmustbereturnedfreightprepaidto  
Multiquip’sdesignatedreceivingpoint.  
PAGE 68 — MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MQ-MIKASA MVH-402DSB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #2 (03/30/05) — PAGE 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION AND PARTS MANUAL  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
MULTIQUIP’SMAINPHONENUMBERS  
800-421-1244  
310-537-3700  
FAX: 310-537-3927  
PARTSDEPARTMENT  
800-427-1244  
310-537-3700  
FAX: 800-672-7877  
FAX: 310-637-3284  
MAYCOPARTS  
800-306-2926  
310-537-3700  
FAX: 800-672-7877  
FAX: 310-637-3284  
SERVICEDEPARTMENT  
800-478-1244  
310-537-3700  
FAX: 310-537-4259  
MQPOWERSERVICEDEPARTMENT  
800-835-2551  
310-537-3700  
FAX: 310-638-8046  
TECHNICALASSISTANCE  
800-478-1244  
FAX: 310-631-5032  
WARRANTYDEPARTMENT  
800-421-1244, EXT. 279 FAX: 310-537-1173  
310-537-3700, EXT. 279  
MULTIQUIP INC.  
POST OFFICE BOX 6254  
CARSON, CA 90749  
310-537-3700 • 800-421-1244  
FAX:310-537-3927  
E-MAIL:mq@multiquip.com  
WWW:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX  
manufactured for Multiquip Inc.  
by  
MIKASA SANGYO CO., LTD. Tokyo, Japan  
Download from Www.Somanuals.com. All Manuals Search And Download.  

New Holland Lawn Mower 600TL Series User Manual
Nikon Digital Camera 26491 User Manual
Nostalgia Electrics Beverage Dispenser CSD 250 User Manual
Olivetti Printer PG L26 User Manual
Omega Vehicle Security Heat Pump FPU5 MT 110 User Manual
Omnimount TV Mount FP CL User Manual
Oster Oven 6247 User Manual
Palsonic CRT Television 6140GY User Manual
Panasonic Camera Lens H F007014 User Manual
Panasonic Flat Panel Television 103PF12U User Manual