OPERATION AND PARTS MANUAL
Plate Compactor
Model
MVC-40G
(Robin EH09-2D Gasoline Engine)
Revision #4 (06/06/07)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Multiquip MVC-40G
Plate Compactor
ROBIN EH09-2D Engine
(EPA)
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions ............................................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation.....................................10-11
General Information ................................................ 12
Components (Plate Compactor) ............................. 13
Components (ROBIN EH09-2D Engine) ................. 14
Inspection........................................................... 15-16
Initial Start-Up .................................................... 17-18
Operation ................................................................ 19
Maintenance ...................................................... 20-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine)................................... 23-24
Troubleshooting (Plate Compactor) ........................ 25
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Crankcase Assembly .........................................36-37
Camshaft Assembly ...........................................38-39
Crankshaft and Piston Assembly .......................40-41
Intake and Exhaust Assembly............................42-43
Air Cleaner Assembly.........................................44-45
Muffler Assembly ...............................................47-47
Governor Assembly ...........................................48-49
Cooling and Starting Assembly..........................50-51
Fuel Tank Assembly ...........................................52-53
Carburetor Assembly .........................................54-55
Electric Device....................................................56-57
Tool Kiit...............................................................58-59
Terms and Conditions Of Sale — Parts .................. 60
Component Drawings
Specification and part number
are subject to change without
Nameplate and Decals....................................... 28-29
Base and Handle Assembly ............................... 30-31
Vibrating Plate and Vibrator Assembly............... 32-33
Engine Assembly ............................................... 34-35
notice.
As a continuing effort to
update our parts book, contact
l
the MULTIQUIP literature
department for the latest
revision of your "Operation
and Parts Manual"
PAGE 4 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
Model
MVC-40G
Centrifugal Force (Blows)
Vibration Frequency
Maximum Forward Speed
Plate Size (L x W)
1,573 ft-lbs (7.2 kN)
6,200 vpm (103 Hz)
75~82 ft/min (23~25 meters/min)
16.53 x 11.41 in (420 x 290 mm)
97 lbs. (43 kg)
Operating Weight
Maximum Area of Compaction
4,711 sq. ft/hr (438 sq. m/hr)
Table 2. ENGINE SPECIFICATIONS
Model
ROBIN EH092D40010
Air-cooled 4 stroke, Single
Cylinder, Horizontal Shaft,
OHV Gasoline Engine
Type
Displacement
Max Output
86 cc.
2.1 kW/4,200 R.P.M.
1.5 kW/3,600 R.P.M.
Continuous Output
Engine
Approx. .40 U.S. gallons
(1.5 liters)
Fuel Tank Capacity
l
Unleaded Automobile
Gasoline
Fuel
Lube Oil Capacity
Spark Plug
.317 qts. (0.3 liters)
NGK BMR4A
(Champion RCJ14)
9.80 x 11.8 x 15.0 in.
(249 x 299 x 380 mm)
Dimension
(L x W x H)
Dry
Net Weight
21.8 lbs. (9.9 Kg.)
PAGE 6 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — DIMENSIONS
Figure 1. MVC-40G Plate Compactor Dimensions
TABLE 3. DIMENSIONS
DESCRIPTION
REFERENCE LETTER
DIMENSION in. (mm)
23.5 in. (597 mm)
20.5 in. (521 mm)
11.25 in. (286 mm)
16.25 in. (413 mm)
19.00 In. (483 mm)
40.50 in. (1,029 mm)
36.00 in. (914 mm)
Height (Lifting Bale)
Height (Lifting Handle)
Width
A
B
C
D
E
F
Length (Plate)
Length (Compactor)
Height (Handle Upright)
Height (Handle Tilted)
G
16.53 x 11.41 in.
(420 x 290)
Plate Dimensions (L x W)
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Potential hazards associated with the operation of the MQ
Lethal Exhaust Gases
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Model MVC-40G Plate Compactor. will be referenced with
Hazard Symbols which appear throughout this manual, and
Lethal Exhaust Gases
will be referenced in conjunction with Safety Message Alert
Symbols.
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MQ Model MVC-
40G Plate Compactor.Refer to the
engine manufacturers instructions
fordatarelativetoitssafeoperation.
WARNING - Lethal Exhaust Gas Hazards
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide ample free flow
air.
Before using this plate compactor, ensure that the operating
individual has read and understands all instructions in this
manual.
SAFETY MESSAGE ALERT SYMBOLS
DANGER - Explosive Fuel Hazards
The three (3) Safety Messages shown below will inform
you about potential hazards that could injure you or others.
The Safety Messages specifically address the level of
exposure to the operator, and are preceded by one of
three words: DANGER, WARNING, or CAUTION.
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
WARNING - Burn Hazards
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
l
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
NOT follow directions.
CAUTION
You CAN be INJURED if you DO NOT follow directions.
WARNING - Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Equipment Damage Hazards
CAUTION - Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
CAUTION - Accidental Starting Hazards
WARNING - Read Manual
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
Before attempting to operate
the plate compactor, and to
avoid serious injury to
personnel, always read and
understand operation manual.
Failure to read and understand
CAUTION - Eye and Hearing Hazards
operation manual
could
result in serious harm or even
death!
ALWAYS wear approved eye and
hearing protection.
DANGER - Refueling Hazard
DO NOT refuel plate copmpactor if compactor is placed
inside truck bed with PLASTIC LINER. Possibility exists
of explosion or fire due to static electricity.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or mixer.
High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance functions. Contact
with hot! components can cause serious burns.
CAUTION - Read Manual!
Failure to follow instructions in this
manual may lead to serious injury or
even death! This equipment is to be
operated by trained and qualified
personnel only! This equipment is for
industrial use only.
■
■
The engine section of this mixer requires an adequate
free flow of cooling air. NEVER operate the compactor
in any enclosed or narrow
The following safety guidelines should always be used when
operating the MQ Mikasa Model MVC-40G Plate Compactor.
area where free flow of the
air is restricted. If the air
flow is restricted it will
cause serious damage to
the compactor or engine
and may cause injury to
people. Remember the
plate compactor's engine gives off DEADLY carbon
GENERAL SAFETY
■
■
■
DO NOT operate or service this equipment before reading
this entire manual.
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
monoxide gas.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool.DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, llness or taking
medicine.
NEVER operate this equipment under the
influence of drugs or alcohol.
■
■
NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the plate compactor.
■
■
Maintain this equipment in a safe operating condition at
all times.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
Manufacture does not assume responsibility for any
accident due to equipment modifications.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 10 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — RULES FOR SAFE OPERATION
■
■
■
NEVER run engine without air filter. Severe engine damage
TRANSPORTING
may occur.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using
compactor.
■
Drain fuel when transporting compactor over long
distances or bad roads.
MAINTENANCE
■
■
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■
NEVER lubricate components or attempt service on a
running compactor.
Refer to the ROBIN Engine Owner's Manual for engine
technical questions or information.
■
ALWAYS allow the plate compactor a proper amount of
time to cool before servicing.
■
■
Keep the compactor in proper running condition.
Fix damage to the plate compactor immediately and
always replace broken parts.
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
Loading and Unloading (Crane)
■
Before lifting, make sure that machine parts (lifting bale and
vibration insulator) are not damaged and screws are not
loosened or lost.
■
■
■
ALWAYS make sure crane or lifting device has been properly
secured to the lifting bale on the compactor.
DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
■
■
■
NEVER lift the compactor while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient strength.
Use one point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath the
machine while lifting.
■
Try not to lift compactor to unnecessary heights.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC-40G is a one direction (forward) walk behind,
plate compactor designed for the compaction of sand, mixed
soils and asphalt.This plate compactor is a powerful compacting
tool capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
compacting for road, embankments and reservoirs as well as
backfilling for gas pipelines, water pipelines and cable installation
work.
The compactor's vibrating plate has a frequency of 6,200 vpm
(vibrations per minute). The travel speed of the compactor is
approximately 82 ft./minute (25 meters/minute).
Engine
The MQ Mikasa MVC-40G Plate Compactor is equipped with a
air-cooled, 4-stroke ROBIN EH09-2D gasoline engine. When
adding fuel, always use unleaded gasoline.
Controls
The MVC-40G is small and lightweight. It can be easily handled
by one person in confined areas. It has an accessible front-
mounted vibrator assembly. The sealed belt cover keeps dirt
and rocks away from the belt.
Before starting the MVC-40G Plate Compactor identify and
understand the function of the controls and components as
indicated Figure 3.
Vibratory Plate
The vibratory plate of the compactor produces low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
The resulting vibrations cause forward motion.The engine and
handle are vibration isolated from the vibrating plate.
l
PAGE 12 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — COMPONENTS (PLATE COMPACTOR)
Figure 3. MVC-40G Plate Compactor Components
5. Vibrating Plate – A flat, open plate made of durable cast
Figure 3 shows the location of the components and general
maintenance parts. The function of each component is described
below:
iron construction used in the compacting of soil.
6. Vibration Case – Encloses the eccentric, gears and
counter weights.
1. Hand Lift Handle – When lifting of the compactor by
personnel is required, use this hand lift handle. DO NOT
attach a crane or heavy lifting device to this handle to lift
the compactor.
7. Gasoline Engine – This plate compactor uses a 4-stroke,
air cooled ROBIN EH09-2D gasoline engine. Refer to the
ROBIN owner's manual for engine information.
2.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
3. Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
4. Belt Cover – Remove this cover to gain acess to the V-
belts.NEVER run the compactor without theV-belt cover.If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — COMPONENTS (ENGINE)
Figure 4. Engine Controls and Components
INITIAL SERVICING
9.
Carburetor – Regulates fuel flow.
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the ROBIN engine service
manualforinstructions anddetailsforproperoperationandservicing.
10. Oil Dipstick/ Filler Cap– Remove the filler cap dipstick
when checking the engine oil level. Add engine oil through
this filler port. See Table 4 for recommended type engine
oil.
1. Throttle Lever – Used to adjust engine RPM. Push lever
upwards for SLOW, and down for FAST.
11. Oil Drain Plug – Remove this plug to drain engine oil from
the crankcase.
2. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly
12. Muffler – Used to reduce noise and emissions. ALWAYS
allow a sufficient amount of time for the muffler to cool before
touching.
3. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Release clips on side of air filter cannister
to gain access to filter element.
Warning - Hot Surface
4. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
the flow of fuel.
Choke Lever – Used in thelstarting of a cold engine, or in
5.
cold weather conditions. The choke enriches the fuel
mixture.
6. FuelTank – Holds .40 gals (1.5 liters)unleaded gasoline.
For additional information refer to ROBIN engine owner's
manual.
13. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch)
Clean spark plug once a week.
7. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
8. Start/Stop Switch – Place this switch in the "ON" position
(1) to start the engine. Place in the "OFF" position (0) to
stop the engine.
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
PAGE 14 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — INSPECTION
The Oil Alert system will
automatically shut-down the
engine if the engine oil level falls
below safe operating limits.
Always be sure to check the
engine oil level prior to starting
the engine.
Before Starting
1. Read safety instructions at the beginning of manual.
2. Cleanthecompactor,removingdirtanddust.Particularly,the
bottom of the plate, engine cooling air inlet, carburetor and
aircleaner.
3. Checktheairfilterfordirtanddust.Iftheairfilterisdirty,blow
throughtheairfiltercartridgefromtheinside,movingajetof
dry compressed air up and down until all dust is removed.
Otherwise replace air filter with a new one.
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
0°C or Lower
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
Danger - Flammable Fuel
Engine Oil Check
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel the compactor if the engine is hot! ,
running or in the dark.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 5) and wipe it clean.
Danger - Flammable Fuel
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is
dry.
Figure 5. Engine Oil Dipstick
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
Fuel Check
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).
UPPER LIMIT
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
LOWER LIMIT
Figure 6. Engine Oil Dipstick
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — INSPECTION
2. TheV-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 9) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
Caution -V-Belt check
NEVER attempt to check theV-belt with the engine running.
Severe injury can occur if your hand (Figure 7) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CLUTCH
PULLEY
Figure 9.V-BeltTension
3. A looseV-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
VIBRATOR
PULLEY
Figure 7.V-Belt Hazard
4. If theV-belt becomes worn or loose, replace it .
1. To check theV-belt tension, remove the bolts that secure
the belt cover to the frame as shown in Figure 8.
Vibrator Oil Check
1. Place the MVC-40Gplate compactor horizontally on a flat
surface.Makesurethecompactorislevelwhencheckingthe
oil in the vibrator assembly.
2. Check vibratoroillevelbyremoving theplug (vibrator oilgauge)
asshowninFigure10. Theoillevelshouldbeuptotheoilplug.
If oil is required, replace using only SAE 10W-30 motor oil.
l
Figure 10.Vibrator Oil Plug
Figure 8.V-Belt Cover Removal
PAGE 16 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — INITIAL START-UP
Caution - Read Manual
DO NOT attempt to operate the plate compactor
until the Safety, General Information and
Inspection sections of this manual have been
read and thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the plate compactor. It is extremely important that
this section be read carefully before attempting to use the
compactor in the field.
Starting the Engine
Figure 13. Engine Choke Lever (Closed)
1. Place the engine fuel valve lever (Figure 11) in the "ON"
4. Place the throttle lever (Figure 14) in the slow position
position.
(idle)
Figure 14.Throttle Lever (Slow)
Figure 11. Engine Fuel Valve Lever (ON Position)
5. Grasp the starter grip (Figure 15) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
2. Place the engine ON/OFF switch (Figure 12) in the "ON "
position.
Figure 12. Engine ON/OFF Switch (ON Position)
Figure 15. Starter Grip
3. Placethechokelever(Figure13)inthe"CLOSED"position
if starting a cold engine, if starting a warm engine or the
temperatureiswarm,placethechokelever in the"OPEN"
position
6. Let the engine warm for a few minutes without a load and
checkfor fuelleaks,andnoisesthatwouldassociatewitha
losecomponent.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — INITIAL START-UP
7. Iftheengineisrunningproperly,slowlyreturn(pushinward)
the choke lever (Figure 13) to the “OPEN” position. If the
engine has not started repeat steps 1 through 6.
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 18).
8. To begin compacting, place the throttle lever (Figure 16) in
the "fast" (run) position.
Figure 18. Engine ON/OFF Switch (OFF)
Figure 16. Throttle Lever (Fast)
3. Place the fuel shut-off lever (Figure 19) in the OFF
position.
CAUTION - Compacting Speed
ALWAYS run engine at full speed while compacting.
Stopping The Engine
Normal Shutdown
Figure 19. Fuel Valve Lever (OFF)
Emergency Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure17)and
run the engine for three minutes at low speed.
1. Move the throttle lever quickly to the SLOW position, and
place the engine ON/OFF switch in the OFF position.
Figure 17.Throttle Lever (Idle)
PAGE 18 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — OPERATION
Operation
CAUTION - Safety Rules
5. Compactortravelingspeedmaydroponsoilswhichcontain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil.To
rectify this problem do the following:
Make sure to follow all safety rules referenced in the safety
sectionofthismanualbeforeoperatingcompactor. Keepwork
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
z
z
z
Check the bottom plate to see if clay or
equivalent material has been lodged in the plate
mechanism. If so, wash with water and remove.
Remember the compactor does not work as
efficiently on clay or soils that have a high
moisture content level.
1. Oncetheenginehasstarted, movetheenginethrottlelever
quickly to the fastposition.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the cen-
trifugalclutch.
If the soil has a high moisture level, dry soil to
appropriate moisture content level or carry out
compaction twice.
Always move the throttle lever
quickly without hesitation, because
increasing the engine speed slowly
causes the clutch to slip.
3. Firmlygaspthecompactor'shandlebar withbothhands,the
compactor will begin moving forward.
4. Slowlywalkbehindthecompactorandbeonthelookout for
anylargeobjectsorforeignmatterthatmightcausedamage
to the compactor or bodily injury.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — MAINTENANCE
CAUTION - Inspection Intervals
CAUTION - Inspection
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number of hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shut down.
Inspection and Maintenance ServiceTables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
CAUTION - Inspection Intervals
Fuel piping and connections should be replaced every 2
years.
TABLE 5. MVC-40G MACHINE INSPECTION
Daily Service
HOURS OF
OPERATION
ITEM
REMARKS
z
Check for leakage of fuel or oil.
Every 8 hours
(every day)
z
Remove soil and clean the bottom of compaction plate.
Check engine oil, see page 15.
Damaged Parts
Loose or Lost Screws
z
z
Every 8 hours
(every day)
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
Function of Controlling Every 8 hours
System Part
(every day)
TABLE 7.
TIGHTENING TORQUE (in. kg/cm) Diameter
Vibrator Oil Check
Every 100 hours See page 16
Every 300 hours See page 21
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm
Vibrator Oil
Replacement
4T
6-8T
11T
*
70
150
250
400
300
500
800
500
800
750
1,100 1,400 2,000
100
150
1,300 2,000 2,700 3,800
V-belt (clutch) Check Every 200 hours See page 21
1,200 2,000 2,900 4,200 5,600
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
Table 6. ENGINE MAINTENANCE
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
* (In case counter-part is of aluminum)
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
(Threads in use with this machine are all right handed)
CHECK
CHANGE
CHECK
X
l
Engine Oil
X
Material and quality of material is marked on each bolt,
and screw.
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
ENGINEOIL
CHECK-CLEAN
REPLACE
CHECK
X
X
1. Drain the engine oil when the oil is warm as shown in
X
Figure 20.
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
3. Replace engine oil with recommended type oil as listed
inTable 4.Engine oil capacity is .317 quarts (.3 liters).DO
NOT overfill.
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the ROBIN Manual for service procedures
4. Install drain bolt with sealing washer and tighten se-
curely.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
PAGE 20 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — MAINTENANCE
Changing Vibrator Oil
1. When changing the vibrator oil, remove the drain plug
(Figure 10), and simply tip the compactor to drain the oil.
Note that the oil will drain more easily while it is hot.
Remember to use only 10W-30 motor oil when replacing
vibrator oil.
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check theV-belt tension.Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
Figure 20. Engine Oil (Draining)
Engine Air Cleaner
1. Remove the air cleaner cover and foam filter element as
shown in Figure 21.
z
Replacing the V-belt
2. Wash the gray foam outer filter element in kerosene or
diesel fuel.Then saturate it in a mixture of 3 parts kero-
sene or diesel fuel and 1 part engine oil. Completely
squeeze the element to remove the mixture and re-install
it back into the air cleaner.
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway ofV-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that theV-belt will come off.
z
Reinstalling the V-belt
EngageV-belt to lower vibrator pulley and push theV-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
z
Checking Clutch
Check the clutch simultaneously withV-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 21. Air Cleaner
Spark Plug
WARNING - V-belt Hazard
1. Remove and clean the spark plug (Figure 22).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
NEVER attempt to check theV-belt with the engine running.
Severe injury can occur if your hand (Figure 7) gets caught
betweentheV-beltandtheclutch.Alwaysusesafetygloves.
CAUTION - Vibration Check
Whenever the compactor's vibration becomes weak or lost
duringnormaloperationregardlessofoperationhours,check
theV-beltandclutchimmediately.
Figure 22. Spark Plug Gap
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— PREPARATION FOR LONG -TERM STORAGE
Compactor Storage
For storage of the compactor for over 30 days, the following
is required:
z
z
z
Drain the fuel tank completely, or add STA-BIL to the
fuel.
Run the engine until the fuel in the fuel in the carburetor
is completely consumed.
Completely drain the oil from the engine crankcase and
follow procedures described in the ROBIN engine
Owner's Manual for engine storage.
z
z
z
Completely drain the compactor's oil from the vibrating
case.
Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the EngineTroubleshooting (Table 8) information
shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult
our company's business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and
clean points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — TROUBLESHOOTING (ENGINE)
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is
proper and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is
proper but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Check entire fuel system for
leaks or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Recoil starter malfunction.
Sprial spring loose?
Replace sprial spring.
l
PAGE 24 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G — TROUBLESHOOTING (PLATE COMPACTOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Compactor Troubleshooting (Table 9)
information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is
and consult our company's business office or service plant.
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
Engine speed too low?
SOLUTION
Set engine speed to correct RPM.
Check or replace clutch.
Clutch slips?
Travel speed too low, and vibration is
weak.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Check eccentric, gears and counter
weights.
Malfunction in vibrator housing?
V-belt slips?
Clutch slips?
Replace V-belt.
Check clutch springs and shoes.
Does not travel forward.
Check vibrator housing (eccentric,
gears and counterweights)
Vibrator locked?
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. .... 1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................ 1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
l
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— SUGGESTED SPARE PARTS
MQ MIKASA MVC-40G PLATE COMPACTOR WITH
ROBIN EH09-2D GASOLINE ENGINE
1 to 3 Units
Qty.
P/N
Description
3 ......... 070100272 ......... V-BELT, A-27 BLUE
4 ......... 939010160 ......... SHOCK ABSORBER
6 ......... 2263261007 ....... ELEMENT SET, AIR CLEANER
3 ......... 0650140380 ....... SPARK PLUG
1 ......... 2745011208 ....... ROPE STARTER
1 ......... 0430440132 ....... FUEL TANK CAP, ASSY.
1 ......... 0641420040 ....... FUEL FILTER, TANK
3 ......... 0642004420 ....... FILTER, V-STD, FUEL STRAINER
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— NAME PLATE AND DECALS
Machine Safety Decals
The MVC-40GPlate Compactor is equipped with a number of safety decals. These decals are provided for operator safety and
maintenance information.The illustration below shows these decals as they appear on the machine.Should any of these decals
become unreadable, replacements can be obtained from your dealer.
l
PAGE 28 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO. PART NO. PART NAME
QTY. REMARKS
1
920203330
0732005181
920206280
920209150
920207690
DECAL; EAR PROTECTION LABEL ............................... 1 ......... NPA-333
2
3
4
5
DECAL; WARNING, HOT SURF., FUMES, GAS, READ . 1
DECAL;DANGER ............................................................ 1 ......... NPA-628
DECAL;V-BELT/ RPF-3270 ............................................. 1 ......... NPA-915
DECAL; CAUTION, READ MANUAL ................................ 1 ......... NPA-769
NAMEPLATE ................................................................... 1 ......... CONTACT MQ PARTS DEPT.
DECAL; EC NOISE REQ. LWA105 .................................. 1 ......... NPA-1033
DECAL; MIKASA, 125MM YELLOW ............................... 1 ......... NP-953
DECAL;CAUTION ........................................................... 1 ......... NPA-929
DECAL;CAUTION ........................................................... 1 ......... NPA-329
DECAL:CAUTION REFUELING ...................................... 1 ......... NPA-1232
6
7
8
9
10
11
920210330
920109530
920203060
920203290
920212320
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— BASE AND HANDLE ASSY.
BASE AND HANDLE ASSY.
PAGE 30 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— BASE AND HANDLE ASSY.
BASE AND HANDLE ASSY.
NO. PART NO.
1
PART NAME
BASE
QTY.
1
REMARKS
417116270
417116820
417339980
417116290
417454400
002210820
002410815
417118330
417454410
417454420
001221052
020310080
952401660
030210250
417215510
953406430
002410820
001211025
030210250
031110160
020310080
020308060
030208200
2
4
5
6
7
8
BELT COVER, IN
COVER SEAL, E/G
BELT COVER, OUT
PLATE, BELT COVER
BOLT, 8X20 H, SW
BOLT, 8X15 H, SW, PW
HANDLE
HANDLE STOPPER
COLLAR, 10.5-20-37.5L
BOLT, 10X60 T
1
1
1
1
2
2
1
2
2
2
1
2
1
1
1
2
10
11
12
13
14
15
16
18
19
20
21
22
23
24
26
27
NUT, M10
WASHER, 103045
WASHER, LOCK M10
HOOK
RUBBER CAP, 16D KP-622
BOLT, 8X20 H, SW, PW
BOLT, 10X25 H
WASHER, LOCK M10
WASHER, FLAT M10
NUT, M10
1
2
1
2
3
3
NUT, M8
WASHER, LOCK M8
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G—VIBRATING PLATE ANDVIBRATOR ASSY.
VIBRATING PLATE AND VIBRATOR ASSY.
PAGE 32 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G—VIBRATING PLATE ANDVIBRATOR ASSY.
VIBRATING PLATE AND VIBRATOR ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
1#
417116663
939010160
020310080
030210250
002411025
417215500
417339920
952400130
002210825
951405240
040406208
417454390
417339890
002210820
031108160
953400270
953405260
417339900
060403020
001520820
417339910
417342700
031110160
417910010
VIBRATING PLATE
SHOCK ABSORBER TAK-50
NUT, M10
1
4
4
4
4
1
1
2
3
4
5
7#
8#
9#
10#
11#
12#
13#
15#
16#
17#
18#
19#
21#
22#
23#
24#
26
WASHER, LOCK M10
BOLT, 10X25 H, SW, PW
ECCENTRIC ROTATOR
PULLEY, A1-82-S22
WASHER, FLAT
BOLT, 8X25 H, SW
KEY, 7X7X19 R
BEARING, 6208C4
PACKING, VIB
CASE COVER, R
BOLT, 8X20 H, SW
WASHER, FLAT M8
PLUG, 1/4X14 10L
PACKING, 1/4 CU
CASE COVER, L
OIL SEAL, TC-30458
SOCKET HEAD BOLT, 8X20 T
COVER SEAL, VIB.
SUPPORT OF STOPPER
WASHER, FLAT M10
1
1
2
2
1
4
4
1
1
1
1
4
1
1
2
27
28
VIBRATING PLATE ASSY ................. 1 .................... INCLUDES ITEMS W/#
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— ENGINE ASSY.
ENGINE ASSY.
PAGE 34 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
MVC-40G— ENGINE ASSY.
ENGINE ASSY.
NO. PART NO.
PART NAME
ENGINE ASSY., EH09-2D
KEY, 5X5X20
COLLAR, 17X30X3
CLUTCH ASSY. D-17
WASHER, FLAT
QTY.
REMARKS
1
911210907
951401740
952404610
417456390
952400130
001220820
030208200
070100272
417456380
413436870
001220825
030208200
031108160
959404350
031108160
022710809
020308060
1
1
1
1
1
1
1
1
1
1
4
4
4
1
1
1
2
2
4
5
6
7
8
9
11
12
13
14
15
16
18
19
20
BOLT, 8X20 T
WASHER, LOCK M8
V-BELT, A-27 BLUE/RPF-3270
PLATE, BOLT W/RUBBER
ENGINE NUT
BOLT, 8X25 T
WASHER, LOCK M8
WASHER, FLAT M8
EARTH WIRE
WASHER, FLAT M8
NYLON, NUT M8
NUT, M8
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CRANKCASE ASSY.
CRANKCASE ASSY.
PAGE 36 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CRANKCASE ASSY.
CRANKCASE ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
10
2841010101
2371420203
2771601001
0440200070
0600200110
0310060020
0105060430
0440060020
0401140030
0211140020
2841340101
0011308180
2841100121
0600200110
2844500301
2054190103
2306360101
TBD
CRANKCASE ASSY................................1............ INCLUDES ITEMS W/%
20 #
26 #
30%
40%
50%
70 #
75%
80
VALVE GUIDE O/S
STEM SEAL
OIL SEAL TB20326
BALL BEARING 6004C3
DOWEL PIN
STUD
OIL SEAL
PLUG
GASKET
BASE
BOLT AND WASHER ASSY.
MAIN BEARING COVER ASSY. .............1............ INCLUDES ITEMS W/
BALL BEARING 6004C3
GOVERNOR GEAR
GOVERNOR SLEEVE
DIPSTICK
O-RING
GASKET, BEARING COVER
FLANGE BOLT
2
1
1
1
2
2
1
2
2
1
4
90
150
160
210
230
*
1
1
1
1
1
1
8
*
250
260
270
280
290
300
610
620
630
631
632
633
637
680
690
700
710
810
820
830
860
2841600303
0110060101
2841300110
2841500113
0110080210
0100080410
0100080420
0110080301
0200080210
2841550103
2841600703
2771501103
0100060400
2841430101
2841440101
2301600613
0110060020
*
CYLINDER HEAD ASSY. ........................1............ INCLUDES ITEMS W/ #
GASKET, HEAD
FLANGE BOLT
BOLT
1
1
1
1
1
1
1
1
2
4
1
1
2
2
BOLT
FLANGE BOLT
WASHER, FLAT
ROCKET COVER
GASKET, ROCKET COVER
PIPE KNOCK
BOLT
BREATHER COVER
BREATHER PLATE
GASKET TAPPET COVER
FLANGE BOLT
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CAMSHAFT ASSY.
CAMSHAFT ASSY.
l
PAGE 38 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
10
34
35
36
37
38
50
2843170211
2273860123
2843640103
0051904100
0031517000
2743870123
2743330103
CAMSHAFT ASSY. ................................ 1 ............ INCLUDES ITEMS W/
*
PIN, SPRING
RELEASE LEVER
SPRING PIN
SNAP RING
RETURN SPRING
TAPPET
1
1
1
1
1
1
*
*
*
*
*
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CRANKSHAFT AND PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
PAGE 40 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CRANKSHAFT AND PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
10
2842070111
0230200100
0230200110
0230200120
0021814000
0032014000
0053203101
0320050010
0200080050
0011308160
2842250120
2842300103
2302330103
2742340103
2742340203
2742340303
2842352107
2842352207
2842352307
0565110010
CRANKSHAFT CP ..................................1............ INCLUDES ITEMS W/
*
40
40
40
50#
60#
70#
SPACER 0.8T
SPACER 1.0T
SPACER 1.2T
NUT
SPRINGWASHER
WOODRUFF KEY
KEY
WASHER
BOLT AND WASHER ASSY.
CONNECTING ROD ASSY......................1............ INCLUDES ITEMS W/#
CONNECTING ROD BOLT
PISTON PIN
1
1
1
1
1
1
1
1
1
80
90
*
100
310
320
350
360
360
360
370
370
370
380
2
1
1
1
1
1
1
1
2
PISTON STD.
PISTON 25 MM. O.S.
PISTON 50 MM. O.S.
PISTON RING SET, STD.
PISTON RING SET, 25 MM.
PISTON RING SET, 50 MM.
CLIP
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — INTAKE EXHAUST ASSY.
INTAKE EXHAUST ASSY.
REF. ONLYREF
l
PAGE 42 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — INTAKE EXHAUST ASSY.
INTAKE EXHAUST ASSY.
NO. PART NO.
PART NAME
QTY.
2
2
1
1
4
2
2
2
2
1
1
1
1
1
1
1
REMARKS
60
2743360103
2743370203
2743340103
2743350103
13210KA031
2743530103
2743600303
2693580103
0170060090
2743650103
1063291203
2843590203
1573500103
0241020010
2064390101
2844710101
2273590403
VALVE SPRING
SPRING RETAINER
INTAKE VALVE
EXHAUST VALVE
COLLET VALVE
PUSH ROD
70
80
90
95
210
220
230
240
260
540
550
560
670
675
680
685
ROCKER ARM
BOLT, PIVOT
NUT
GUIDE PLATE
INSULATOR
GASKET, INTAKE
GASKET, INSULATOR
GROMMET
KNOB
CHOKE BRACKET
GASKET, 2 IN. NEWPUSTD
1
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — AIR CLEANER ASSY.
AIR CLEANER ASSY.
l
PAGE 44 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
510
520
PART NO.
2843261000
2263261007
2273590403
2263921200
2841610103
PART NAME
QTY.
REMARKS
AIR CLEANER ASSY. .......................... 1 .............. INCLUDES ITEMS W/
*
ELEMENT SET
1
1
2
1
*
538
570
850
GASKET, 2 IN. NEW PU STD.
NUT & WASHER ASSY.
RUBBER PIPE
*
*
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — MUFFLER ASSY.
MUFFLER ASSY.
REF. ONLY
PAGE 46 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — MUFFLER ASSY.
MUFFLER ASSY.
NO. PART NO.
PART NAME
QTY.
REMARKS
310
320
340
360
365
366
440
445
2843010112
2843420101
2843520103
0152060090
0011306160
0011408160
2363700101
0150040050
MUFFLER
1
1
1
3
2
2
1
2
MUFFLER COVER
GASKET, EXHAUST
TAPPING BOLT
BOLT & WASHER ASSY
BOLT/WASHER 8X16
DEFLECTOR
TAPPING SCREW
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — GOVERNOR ASSY.
GOVERNOR ASSY.
l
PAGE 48 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — GOVERNOR ASSY.
GOVERNOR ASSY.
NO. PART NO.
PART NAME
QTY.
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
REMARKS
10
2844230603
2304220103
2344270101
2344280113
0031305000
0011406250
0186060020
2844250603
2844330101
2304500111
0110060010
0043106300
0022706000
2274350113
2274500203
0217060030
0110060030
GOVERNOR LEVER
GOVERNOR SHAFT
GOVERNOR ROD
ROD SPRING
20
30
40
50
60
70
80
200
201
207
230
240
250
252
255
280
CLIP
BOLT & WASHER ASSY.
NUT
GOVERNOR SPRING
SPEED CONTROL CP
BASE PLATE CP
FLANGE BOLT
SCREW
NUT
STOP PLATE STD.
SPRINGWASHER
FRICTIONWASHER
FLANGE BOLT
1
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — COOLING, AND STARTING ASSY.
COOLING STARTING ASSY.
PAGE 50 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — COOLING, STARTING ASSY.
COOLING STARTING ASSY.
NO.
10
20
21
40
41
60
80
92
110
210
210-1
210-2
210-3
210-4
210-5
210-6
210-7
210-8
210-11
210-24
210-25
210-49
220
PART NO.
2845130101
2849510203
0732005470
0010408160
0010408505
2845260123
0110060010
0023808000
2845410103
2845021120
2745011508
2745012018
2745011208
2615010008
2705012508
2745013108
2275013508
2705026108
2845014508
2745015208
1315015008
22745015208
0110060010
0110060020
PART NAME
QTY.
REMARKS
BLOWER HOUSING
LABEL, MODEL
LABEL, TM
1
1
1
3
1
1
1
1
1
FLANGE BOLT
FLANGE BOLT
CYLINDER BAFFLE
FLANGE BOLT
FLANGE NUT
COOLING BLOWER
RECOIL STARTER ASSY. ................. 1 .............. INCLUDES ITEMS W/
SPIRAL SPRING
REEL
STARTER ROPE
STARTER KNOB
RATCHET
FRICTION SPRING
RETURN SPRING
RATCHET GUIDE
STARTER PULLEY
SLIDE PLATE B
SLIDE PLATE
*
1
1
1
1
1
1
1
1
1
1
1
1
3
4
*
*
*
*
*
*
*
*
*
*
*
*
SET SCREW
FLANGE BOLT
FLANGE BOLT
230
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 52 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
10
20
PART NO.
PART NAME
FUEL
LABEL, EXP.
QTY.
1
1
REMARKS
2846010102
0732005181
0430440132
0434180012
0841260020
0210260050
0232420012
0213310020
0641420040
0642004402
0642004420
0642004490
0642004460
0023808000
0023806000
0110060020
2846260201
0561080020
0200080220
0110060570
2846160102
2846160203
2846500103
30
FUEL TANK CAP ASSY. .................... 1 .............. INCLUDES ITEMS W/
INNER CAP
SPONGE
GASKET CAP
PARTITION PLATE
GASKET (FILTER)
FUEL FILTER
FUEL STRAINER ASSY. ................... 1 .............. INCLUDES ITEMS/W#
FILTER, V-STD
JYOINT PIPE, V-STD
HOSE BAND ASSY. V-STD.
FLANGE NUT
FLANGE NUT
FLANGE BOLT
FUEL PIPE ASSY.
HOSE CLAMP
WASHER
*
32
1
1
1
1
1
1
*
33
*
34
*
35
36
40
*
50
50-21#
50-22#
50-23#
60
61
63
1
1
1
1
4
4
1
2
1
2
1
1
1
70
INCLUDES ITEMS/W%
90%
103
105
110
111
145
FLANGE BOLT
FUEL TANK BRACKET
BRACKET, 2 TANK
SPONGE, TANK BRACKET
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 54 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
210
211
PART NO.
2846232200
2846253508
2846245508
2846252708
2846242008
2846252208
2796256318
2846253208
2846235508
2796256408
2796250008
2846251508
2846255208
2516235008
2846254008
2846250508
2846240008
2846245608
2516266108
2776258108
2516244908
2516255908
2846256008
2846245008
2846245108
2846256308
2846245608
PART NAME
QTY.
REMARKS
CARBURETOR ASSY. ....................... 1 .............. INCLUDES ITEMS W/
*
THROTTLE VALVE
CSREW
VALVE CHOKE
SLOW JET
LEVER ASSY. CHOKE
COLLAR SHAFT, 1
SHAFT SUB. ASSY. TH.
SCREW
COLLAR SHAFT, 2
VALVE NEEDLE ASSY.
PIN, FLOAT LEVER
CHAMBER ASSY. FLOAT
GASKET
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
*
212
213
215
218
219
221
222
223
224
225
226
227
228
229
232
233
238
250
251
312
313
361
362
363
364
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
GASKET CHAMBER
FLOAT ASSY.
MAIBN JET
SCREW
DRAIN SCREW
SCREW ADJUST
SPRING
BUSH
COLLAR
O-RING
O-RING
PLATE
SCREW
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — ELECTRIC DEVICE ASSY.
ELECTRIC DEVICE ASSY.
PAGE 56 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — ELECTRIC DEVICE ASSY.
ELECTRIC DEVICE ASSY.
NO.
10
11
30
60
70
75
100
110
PART NO.
2847934001
2847943021
0011706250
0660000371
0150040090
0566030010
0650140380
2847510203
PART NAME
QTY.
REMARKS
FLY WHEEL CP
1
1
2
1
2
1
1
1
IGITION COIL CP
BOLT & WASHER ASSY.
STOP SWITCH ASSY., ON-OFF
TAPPING SCREW
CLAMP
SPARK PLUG
SPARK PLUG CAP
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — ELECTRIC DEVICE ASSY.
ACCESSORY TOOL KIT
PAGE 58 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EH09-2D — ACCESSORYTOOL KIT.
ACCESSORY TOOL KIT
NO.
10
PART NO.
2269030710
PART NAME
ACCESSORY TOOL KIT
QTY.
1
REMARKS
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: February 22, 2006
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
l
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 60 — MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MVC-40G PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (06/06/07) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ Parts Department
800-427-1244
Tel. (800) 421-1244
Fax (800) 537-3927
Fax:800-672-7877
Fax:310-637-3284
310-537-3700
Contact: mq@multiquip.com
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2007, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-40G Plate Compactor.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Milwaukee Cordless Drill 5386 59 User Manual
MTD Automobile Electronics APS 620 User Manual
MTX Audio Stereo Amplifier Thunder202 User Manual
Multi Tech Systems Network Card MT202TD 1200 User Manual
Nespresso Espresso Maker Le Cube User Manual
NeumannBerlin Microphone SM 69 fet User Manual
Nokia GPS Receiver LD 2 User Manual
NXP Semiconductors Switch PIP3210 R User Manual
Omnimount TV Mount 1004186 User Manual
Onkyo Home Theater System 29400218 User Manual