OPERATION AND PARTS MANUAL
SERIES
HPLA/HPHA-SERIES 36"
WALK-BEHIND TROWEL
(HONDA GX240K1QA2 GASOLINE ENGINE)
Revision #3 (07/06/10)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
P/N 21362
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL—TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
HONDA GX240K1QA2ENGINE
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Training Checklist ...................................................... 6
Daily Pre-Operation Checklist ................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation ..................................10-11
Operation And Safety Decals.................................. 12
Specifications (Trowel) ............................................ 13
Specifications (Engine) ........................................... 14
General Information ................................................ 15
Air Cleaner Asssembly .......................................64-65
Camshaft Asssembly .........................................66-67
Carburetor Asssembly .......................................68-69
Control Asssembly .............................................70-71
Crankcase Cover Asssembly .............................72-73
Crankshaft Asssembly .......................................74-75
Cylinder Barrel Asssembly .................................76-77
Cylinder Head Asssembly ..................................78-79
Fan Cover Asssembly ........................................80-81
Flywheel Asssembly...........................................82-83
Fuel Tank Asssembly .........................................84-85
Ignition Coil Asssembly ......................................86-87
Muffler Asssembly..............................................88-89
Piston Asssembly ...............................................90-91
Recoil Starter Asssembly...................................92-93
Engine Labels ....................................................94-95
MQ WHITEMAN — HPLA/HPHA
SERIES 36" TROWEL
Controls and Components ................................. 16-17
Basic Engine ........................................................... 18
Assembly and Installation ..................................19-21
Pre-Inspection ....................................................22-23
Initial Start-Up ....................................................24-25
Operation ...........................................................26-27
Options...............................................................28-29
Maintenance (Engine)........................................30-34
Maintenance (Trowel) ........................................32-36
Troubleshooting (Trowel) ...................................37-38
Troubleshooting (Engine)........................................ 39
Explanation of Codes .............................................. 40
Suggested Spare Parts ........................................... 41
Nameplate and Decals.......................................42-43
Standard Handle Assembly ...............................44-45
Quick Pitch™ Handle Assembly........................46-49
4-Blade Spider Assembly...................................50-51
Gearbox & Engine Mounts Assembly ................52-55
Engine Assembly ...............................................56-57
Guard Ring Assembly ........................................58-59
Blades and Arm Adj. Fixture Assembly ..............60-61
Lifting Bail Assembly (Option) ............................62-63
Terms and Conditions of Sale — Parts ................... 96
Specification and part number
NOTE
are subject to change without
notice.
PAGE 4 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
N View Parts Diagrams
N Order Parts
N Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
Order via Phone:
1-800-427-1244
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
R
R
R
R
R
R
Dealer Account Number
R
Specify Preferred Method of Shipment:
Dealer Name and Address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
N
N
Priority One
Ground
Shipping Address (if different than billing address)
Return Fax Number
N Next Day
Second/Third Day
Applicable Model Number
N
Quantity, Part Number and Description of Each Part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL—TRAINING CHECKLIST
TRAINING CHECKLIST
This checklist will lists some of the minimum requirements for
machine maintenance and operation. Please feel free to detach
it and make copies. Use this checklist whenever a new operator
is to be trained or it can be used as a review for more experienced
operator’s.
TRAINING CHECKLIST
DESCRIPTION
Read Operator’s Manual completely.
NO.
OK?
DATE
1
Machine layout, location of components, checking of engine and
gearbox fluid level.
2
3
4
Fuel system, refueling procedure.
Operation of controls (machine not running).
Safety controls, safety stop switch operation.
Emergency stop procedures.
Startup of machine.
5
6
7
8
Maneuvering.
9
Pitching.
10
11
12
13
Concrete finishing techniques.
Shutdown of machine.
Lifting of machine.
Machine transport and storage.
Operator _________________________________________ Trainee __________________________________________
COMMENTS:
PAGE 6 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
1
2
3
4
5
6
Engine Oil Level.
Gearbox Fluid Level.
Condition of Blades.
Blade Pitch Operation.
Safety Stop Switch Operation.
V-Belt Clutch Operation.
COMMENTS:
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36" TROWEL- SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
NOTE
This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MultiQuip HPLA/HPHA-SERIES 36" WALK-
BEHIND TROWEL.
For engine maintenance
information, please refer to the engine manufacturers
instructions for data relative to its safe operation.
Before using this WALK-BEHIND TROWEL, ensure
that the operating individual has read and
understands all instructions in this manual.
Explosive Fuel
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you DO NOT follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. NEVER operate the engine with
heat shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you DO NOT follow
directions.
Rotating Parts
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair
and clothing away from all moving parts to
prevent injury.
CAUTION: You CAN be injured if you
DO NOT follow directions.
Potential hazards associated with HPLA/HPHA-SERIES 36"
Trowel operation will be referenced with "Hazard Symbols"
which appear throughout this manual, and will be referenced in
conjunction with Safety "Message Alert Symbols".
PAGE 8 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36" TROWEL- SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF
switch in the OFF position, when the
trowel is not in use.
ALWAYS wear approved respiratory protection.
Over Speed Conditions
Sight and Hearing hazard
NEVER tamper with the factory settings of the
engine governor or settings. Personal injury
and damage to the engine or equipment can
result if operating in speed ranges above
maximum allowable.
ALWAYS wear approved eye and hearing
protection.
Equipment Damage Messages
This walk-behind trowel, other
property, or the surrounding
environment could be damaged if
you do not follow instructions.
Other important messages are provided throughout this manual
to help prevent damage to your trowel, other property, or the
surrounding environment.
NOTE
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
the trowel.
CAUTION:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
The following safety guidelines should always be used when
operating the HPLA/HPHA-SERIES 36" walk-behind trowel.
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
SAFETY
■
DO NOT operate or service this equipment
before reading this entire manual.
The engine of this trowel requires an adequate free flow of
cooling air. NEVER operate the trowel (except electric models)
in any enclosed or narrow
■
■
This equipment should not be operated by
persons under 18 years of age.
area where free flow of the
air is restricted. If the air flow
is restricted it will cause
serious damage to the
NEVER operate the trowel without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required by the job.
trowel's engine and may
cause injury to people.
Remember the trowel's
engine gives off DEADLY
carbon monoxide gas.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool.
NEVER operate the trowel under the
influence or drugs or alcohol.
■
NEVER smoke around or near the
machine. Fire or explosion could result from
fuel vapors, or if fuel is spilled on a hot!
engine.
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
■
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
■
■
NEVER operate the trowel in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS check the trowel for loosened threads or bolts
before starting.
Topping-off to filler port is dangerous, as it tends to spill fuel.
PAGE 10 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— RULES FOR SAFE OPERATION
■
■
■
■
■
■
DO NOT operate this trowel unless all guards and safety
devices are attached and in place. See pages 16 and 17.
■
■
Keep the trowel in proper running condition.
Make sure that there is no buildup of concrete, grease, oil or
debris on the trowel.
ALWAYS use proper lifting techniques when moving the
trowel. See page 24.
■
■
■
Fix damage to the trowel immediately and always replace
broken parts.
ALWAYS check to make sure that the operating area is clear
before starting the engine.
Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
ALWAYS test the safety stop switch devices before
operating the trowel.
High Temperatures – Allow the machine and engine to
cool before adding fuel or performing service and
maintenance functions. Contact with hot! components can
cause serious burns.
NEVER place your feet or hands inside the guard rings
while starting or operating this equipment.
AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.
CAUTION
EMERGENCIES
■
ALWAYS keep clear of rotating or moving parts while
operating the trowel.
■
■
NEVER leave the machine unattended while running.
■
ALWAYS know the location of
the nearest fire extinguisher.
Moving Parts – Shut down the engine before performing
service or maintenance functions. Contact with moving parts
can cause serious injury.
Maintenance Safety
■
■
■
■
■
Disconnect the spark plug wires before attempting any type
of service.
■
■
ALWAYS know the location of the
nearest and first aid kit.
Securely support any machine components that must be
raised.
NEVER lubricate components or attempt service on a running
machine.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— OPERATION AND SAFETY DECALS
Machine Safety Decals
The HPLA/HPHA-SERIES 36" walk-behind trowel is equipped with a number of safety decals. These decals are provided for
operator safety and maintenance information. Figure 1below illustrates these decals as they appear on the machine. Should any of
these decals become unreadable, replacements can be obtained from your dealer.
CAUTION
WARNING!
INJURY COULD RESULT IF FINISHER IS LIFTED
WITHOUT PITCH HANDLE FIRMLY ENGAGE
DO NOT LIFT MACHINERY BY GUARD
RING. MAY CAUSE DAMAGE TO
GUARD RING SHOCK MOUNTS
USE LIFT HANDLES ONLY
P/N 20526
P/N 1261
WARNING!
DO NOT OPERATE HANDLE UNTIL IT IS
SECURELY FASTENED TO POWER TROWEL
& INSTRUCTIONS HAVE BEEN READ
P/N 1940
P/N 20527
P/N 1736
T
E
E
F
R
L
O
O
C
TC
H
I
™
P
-
H
A
N
K
N
D
C
I
L
U
O
R
E
Q
C
FINISHER
BOISE, IDAHO USA
I
C
U
K
Q
P
U. S. PATENT
XXXXXXX
P
O
B
L
E
O
A
S
I
W
S
W
U
E
,
C
E
O
O
R
O
H
A
I
R
R
E
H
D
N
T
C
H
R
I
N
S
I
E
I
F
T
TE
C
P/N 1848
P/N 1492
P/N 12405
P/N 1758
METRIC
GENUINE
TROWEL
PRELOAD TRIM INDICATOR
FINISH
MADE IN USA
FINISH
COMBO
COMBO
J
B
P/N 2938
P/N 1735
P/N1499
Symbol indicates that it is mandatory to wear
safety glasses, safety helmet and ear protection.
NAMEPLATE
CONTACT MULTIQUIP
SERVICE DEPT.
P/N 11247 (Part of decal kit 12620)
Symbol indicates that it is mandatory to
wear safety shoes, with extra protection
(steel toed).
Symbol indicates that it is mandatory to wear
gloves.
P/N 11247 (Part of decal kit 12620)
P/N 11247 (Part of decal kit 12620)
Radiating heat symbol. Symbol indicates equipment
is hot.
This is the symbol for belt drive.
P/N 11246 (Part of decal kit 12620)
P/N 11246 (Part of decal kit 12620)
Symbol for examining or checking of the machine.
Mostly used for maintenance. Check lubrication
oil in gearbox.
This is the symbol for gear drive.
P/N 11246 (Part of decal kit 12620)
P/N 11246 (Part of decal kit 12620)
Figure 1. HPLA/HPHA-SERIES 36" Trowel Decals
PAGE 12 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— SPECIFICATIONS (TROWEL)
SideView
Figure 2. HPLA/HPHA-SERIES 36" Trowel
Dimensions
Table 1. HPLA/HPHA-Series 36" Trowel Specifications
A– Height (Lifting Hook)
B– Height Engagement Lever)
36.7 in (931.6 mm)
41.4 in (1,044.2 mm)
36.5 (927.1 mm)
C–Width
70.5 (1,789.4 mm)
174 lbs./79.1 Kg.
94 db
D–Length
Weight – Operating
Sound Pressure
Vibration
Ring Diameter
Number of Blades
Blade Tip Speed – FPM (m/s)
Rotor – RPM (Gasoline)
Path Width – in. (cm)
2.0g (19.6 m/s2)
36.5 in (92.7 cm)
4
1,182 fpm (6.0 m/s)
100 rpm
36 in. (91.4)
NOTE:
2. The vibration level indicated is the maximum RMS (Root
Mean Square) value obtained at the handle grip while
operating the walk-behind trowel on curing concrete in a
manner most often experienced in “normal” circumstances.
Values were obtained from all three axes of motion. The
values shown represent the maximum RMS value from
these measurements.
1. Sound pressure is a weighted measure. Measured at the
operators ear position while the walk-behind trowel is
operating at full throttle on concrete in a manner most often
experienced in “normal” circumstances. Sound pressure
may vary depending upon the condition of the concrete.
Hearing protection is always recommended.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— SPECIFICATIONS (ENGINE)
Table 2. Specifications (Engine)
Model
HONDA GX240K1QA2
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal Shaft
Gasoline Engine
Type
2.9 in. x 2.3 in.
(73 mm x 58 mm)
Bore X Stroke
Displacement
Max Output
14.81 cu-in. (242cc)
8.0 H.P./3600 R.P.M.
Fuel Tank Capacity
Fuel
1.59 U.S. gal. (6 liters)
Unleaded Automobile Gasoline
1.16 U.S. qt. (1.1 liters)
Lube Oil Capacity
Speed Control
Method
Centrifugal Fly-weight Type
Recoil Start
Starting Method
Dimension
(L x W x H)
14.0 x 16.9 x 16.1 in.
(355 x 430 x 410 mm)
Dry Net Weight
55.1 lbs. (25 Kg)
PAGE 14 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— GENERAL INFORMATION
Blades
HPLA/HPHA-SERIES 36" Walk-Behind Trowel
Familiarization
The blades of the trowel finish the concrete as they are rotated
around the surface. Blades are classified as combination (8
inches wide), float (10 or 8 inches wide), and finish (6 inches
wide).This trowel comes equipped with either three or four
blades per rotor equally spaced in a radial pattern and
attached to vertical rotating shaft by means of a spider
assembly.
This walk-behind trowel is designed for the floating and
finishing of concrete slabs.
Take a walk around the trowel. Take notice of all the major
components (see Figure 3, pages 16 and 17) like the engine,
blades, quick pitch control, air cleaner, centrifugal stop switch
etc. Check that there is always oil in the engine.
Centrifugal Stop Switch
Read all the safety instructions carefully.Safety instructions will
be found throughout this manual and on the trowel. Keep all
safety information in good, readable condition. Operators should
be well trained on the operation and maintenance of the trowel.
In the event of a trowel runaway condition (operator releases
the handle), a centrifugal stop switch will stop the engine
and bring the trowel to a halt.
Before using your trowel, test it on a flat watered down section of
finished concrete that is free of any debris and other objects.
CAUTION
This trial test run will increase your confidence in using the trowel
and at the same time it will familiarize you with the trowel’s
controls. In addition you will understand how the trowel handles
under actual conditions.
NEVER attempt to lift the trowel by yourself.
ALWAYS get the assistance of another
person to help lift the trowel or use a crane
or lifting device to move the trowel.
Engines
This trowel is available with an 8.0 HP HONDA gasoline engine.
Refer to the engine owner’s manual for instructions regarding
the operation and maintenance of your engine. The engine
manual is included with your trowel at the time of shipment from
Whiteman. Please contact your nearest Multiquip Dealer for a
replacement should the original manual disappear.
Moving the HPLA/HPHA-SERIES 36"Walk-BehindTrowel
This walk-behind trowel is designed to be moved and handled
in several ways.The easiest way to lift the trowel is to use the
auxiliary lifting tube that is attached to the main handle. See
page 24. When using the auxiliary tube, always use two
persons to lift the trowel.
Drive System
Power is transferred from the engine to the gearbox input shaft
via a V-belt or pulley drive system.The pulley engages using a
centrifugal clutch.
Some models have a lifting bail (option) installed. A strap or
chain can be attached to the lifting bail, allowing a forklift or
crane to lift the trowel up onto a slab of concrete. Use a lifting
device of adequate lifting capacity to lift the trowel.
Gearbox
Training
The gearbox is located beneath the engine and transfers power
to the rotor or spider assembly. The gearbox controls the
rotational speed of the trowel and is equipped with two shafts
(input and output).
For proper training, please use the “TRAINING CHECKLIST”
located in the front of this manual (Page 6).This checklist will
provide an outline for an experienced operator to provide training
to a new operator.
Spider
The vertical output shaft of the gearbox connects to a cast hub
called the spider.The spider has 4 arms that extend outward
that are used for attachment of blades or other accessories.
Remember as the gearbox output shaft rotates so does the spider
assembly.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— CONTROLS AND COMPONENTS
PAGE 16 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— CONTROLS AND COMPONENTS
(Figures 3) shows the location of the basic controls or
components, for the HPLA/HPHA-SERIES 36" trowel. Listed
below is a brief explanation of each control or component
14. Guard Ring – NEVER put hands or feet inside guard ring.
15. Engine –This trowel uses an 8HP Honda gasoline engine.
1. Quick Pitch™ Control Handle – To adjust the pitch of
the blades, grasp the handle then squeeze and either move
the handle forward or backward to achieve the desired
blade pitch.
2. Handlebar Adjuster – Change the angle/height of the
handle bars by loosening star wheel, adjust handlebars to
desired location, tighten starwheel firmly to hold handlebars
in that position.
3. Hand Grip/Handle Bar – When operating the trowel, place
both hands on each grip to maneuver the trowel. Replace
hand grips when they become worn or damaged.
4. Throttle Control Lever – Controls the speed of the engine.
Pull the hand grip toward the operator to increase engine
speed (high), away from the operator to decrease engine
speed (low or idle).
5. Throttle (Engine) – Controls engine speed when throttle
control lever is pulled toward the operator.
6. V-Belt Cover – Remove this cover to gain access to theV-
belt. NEVER operate the trowel with this cover removed.
7. Centrifugal Safety Stop Switch – In the event the operator
loses control of the trowel, this switch will shut-down the
engine.
8. Auxiliary LiftingTube - Use this tube to lift the trowel onto
a slab.Tube is to be inserted into socket located in front of
the gearbox.
9. Trowel Arm – NEVER operate the trowel with a bent, broken
or out of adjustment trowel arm. If the blades show uneven
wear patterns or some blades wear out faster than others,
the trowel arm may need to be adjusted. Use the trowel
arm adjustment tool P/N 1817 to adjust the trowel arms.
10. Trowel Lifting Point – Insert the auxiliary lifting tube here.
See page 24.
11. Pitch Control (standard models) -Turn this "StarWheel"
clockwise for increase blade pitch, and counter-clockwise
for decrease blade pitch.
12. Blades –This trowel is equipped with combination blades.
These blades are versatile and should take care of most
troweling needs. In addition float discs can be attached to
the trowel arms that will allow the trowel to float on "wet"
concrete.
13. MainTube -When disassembling components inside the
tube exercise extreme CAUTION! Tube is spring-loaded,
severe injury could result if not disassembled correctly.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— BASIC ENGINE
Figure 4. Engine Controls and Components
INITIAL SERVICING
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
DANGER
NOTE
allow dirt to enter the engine, causing
rapid engine wear.
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT attempt to start the
engine until the fuel residue has been completely wiped up, and the
area surrounding the engine is dry.
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.7 - 0.8 mm (0.028 - 0.031 inch) Clean
spark plug once a month. (More often depending on use.)
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
9. Muffler – Used to reduce noise and emissions.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
10. Fuel Tank – Holds unleaded gasoline. For additional
the flow of fuel.
information refer to engine owner's manual.
PAGE 18 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — ASSEMBLY AND INSTALLATION
Assembly and Installation
Before the trowel can be put into operation there are some
components that must be installed before the trowel can be used.
This section provided general instructions on how to install those
components. Instruction sheet P/N 20485 provides further details
for the handle assembly.
HandleTube Installation (All Models)
1. Install the handle tube to the gearbox as shown in (Figure 5).
The mounting hardware should be contained in the shipping
container.
Figure 6. Handlebar Installation
Throttle Cable Installation
1. Place the throttle lever (Figure 7) to the idle position.
Figure 7. Throttle
Figure 5. HandleTube Installation
2. Feed the throttle cable through the cable housing.
2. On Quick-Pitch™ models, pivot the T-handle back (full
pitch). See Figure 6. This will relax the spring inside the
handle tube. On either model, spread the handle bar ends
just enough to engage the teeth on the handle tube. Attach
the hand wheel assembly, position handlebar to desired
location, and tighten hand wheel firmly.
3. Connect the throttle cable to the engine. (Figure 8). There
should be a piece of wire installed on the trowel to show
wheretoroutethethrottlecable.Whenconnectingthecable
housing, make sure that no more than 1/4" (6.4mm) of the
cable housing protrudes past the housing clamp on the
engine.
CAUTION
The Quick-Pitch™ handle is spring loaded,
personal injury or damage could result from
improper handling or installation. Be careful
when installing this component.
2.
Considerable force may be
required when moving the Quick-
NOTE
Pitch
™
T-handle forward or
backward.
Figure 8. Throttle Cable Connection
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — ASSEMBLY AND INSTALLATION
4. Tighten cable clamp screw and swivel stop screw.
5. After the cable has been installed on the engine, adjust
and tighten operator position of the handle to lock the
throttle cable at the proper length.
6.
Adjust cable tension loosening the lock nut on the throttle
cable receiver (Figure 9), loosening or tightening the
adjuster nut below it, then retightening the lock nut.
Figure 9. Throttle Adjust
7. These are general instructions. Installation of the throttle
cable may vary for different engine configurations. Please
lookformoredetailedinstructionsinsidetheboxcontaining
thehandle.Thesemoredetailedinstructionsshouldprovide
adequate guidance for installing.
Figure 10. Engine Safety StopWire Connection
Pitch Cable Installation
1. Expose the pitch cable to maximum by adjusting the handle
pitch to the "no pitch" position. On the standard model turn
the pitch control counter-clockwise, (Figure 11). On the
Quick-Pitch™ model, pivot the pitch handle forward or no
pitch, (Figure 12).
Handle Height Adjustment
Ifhandleheightadjustmentisdesired,ahandlewedgekitcanbe
purchasedforyourtrowelbyorderingP/N2576fromyourMultiquip
dealer.These wedges are placed between the handle and the
gearbox to adjust the operating height of the handle. This kit
comes complete with wedges, new bolts and installation
instructions.This will move your operating handle position up or
downapproximately3”(76mm).
Safety Stop SwitchWire
Locate the safety stop switch wire protruding from the handle
tube (Figure10) and connect it to the tail wire on the engine.
Test the safety stop switch to insure proper operation.
Figure 11. "No Pitch" Position (Standard)
Figure 12. "No Pitch" Position (Quick-Pitch™)
PAGE 20 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — ASSEMBLY AND INSTALLATION
Pre-load Adjustment (Quick-Pitch™ Models Only)
2. Lock the spring in the compressed position, by releasing
the blade pitch adjustment trigger, (Quick-Pitch™ model).
1. After the Quick-Pitch™ handle has been installed on the
trowel, spring pre-load adjustment will be required.
3. Remove one brass set nut from the blade pitch cable end
as shown in (Figure 13).
2. Locate the adjustment screw on the underside of the handle
tube (Figure 15).
4. Thread the second brass set nut towards the cable as far
as possible.
Figure 13. Blade Pitch Cable
5. Insert the cable end through the yoke eyelet (Figure 14)
Tighten the first brass set nut by hand to remove all the
slack from the cable.
Figure 15. Pre-load Adjustment
3. A decal has been placed on the side of the handle tube to
6
Using a wrench, tighten the second brass set nut up against
the yoke boss.This will lock the cable in place.
assist the user in the adjustment of the spring.
4. Align the arrow on the adjustment screw with the letter "J"
7. Use a wrench and finish tightening the first brass set nut up
against the yoke boss.
COMBO on the decal.
5. Test the pitch control operation and adjust if necessary.
YOKE
THREAD CABLE END
THROUGH YOKE EYELET
TIGHTEN SECOND
BRASS SET NUT
AGAINST YOKE BOSS
USE A WRENCH TO
TIGHTEN FIRST BRASS
SET NUT AGAINST YOKE BOSS
Figure 14. CableYoke Attachment
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— PRE-INSPECTION
CAUTION
NEVER operate the trowel
in a confined area or
enclosed area structure
that does not provide ample
free flow of air.
ALWAYS wear approved eye and hearing
protection before operating the trowel.
Figure 16. Engine Oil Dipstick (Removal)
NEVER place hands or feet inside the guard
rings while the engine is running.ALWAYS shut
the engine down before performing any kind of
maintenance service on the trowel.
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
4. Iftheoillevelislow(Figure17), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table3).Maximum oil
capacityis1.16USQt. (1.1liters).
It is recommended that the trowel's safety stop switch be used
to stop the engine after every use. Doing this will verify that the
switch is working properly and presents no danger to the operator.
Reference manufacturer engine
manual for specific servicing
NOTE
instructions.
Before Starting
1. Read safety instructions at the beginning of manual.
2. Clean the trowel, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Checkfasteningnutsandboltsfortightness.
Figure 17. Engine Oil Dipstick (Oil Level)
Table 3. Oil Type
Engine Oil Check
1. Tochecktheengineoillevel,placethe trowelonsecurelevel
ground with the engine stopped.
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
2. Remove the filler dipstick from the engine oil filler hole
(Figure 16) and wipe it clean.
0°C or Lower
PAGE 22 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL— PRE-INSPECTION
Blade Check
Explosive Fuel
Check for worn or damaged blades. Check to see if one blade is
worn out while the others look new.If this is the case there could
be a blade pitch problem. Refer to the maintenance section of
this manual for blade pitch adjustment procedure. Replace any
worn blades.
Fuel Check
Motor fuels are highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the trowel if the engine is hot! or running.
CONTROLS
Safety Stop Switch
1. Remove the gasoline cap located on top of fuel tank.
This trowel has been equipped with a centrifugal safety stop
switch. (Figure 19)
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Gearbox Oil
1. Determine if the gearbox oil is low by removing the oil
plug located on the side of the gearbox.This plug will be
marked by the "check" decal.See (Figure 18).The correct
level of the lubrication oil should be to the bottom of the fill
plug.
GEARBOX
Figure 19. Centrifugal Safety Stop Switch
The switching mechanism of this switch should operate freely
and should always be kept in this condition. With the switch in
theOFFposition,theengineshouldnotstartorrun.Thepurpose
ofthisswitch istostoptheengineinarunawaysituation,(i.e. the
operator releasing the handle during operation). Safety stop
switches should be tested every time the engine is started. See
page25 forprocedures tochecktheoperationoftheSafetyStop
Switch.
OIL SIGHT/
FILL PLUG
DRAIN
PLUG
Figure 18. Gearbox
2. If lubrication oil begins to seep out as the drain plug is
being removed, then it can be assumed that the gearbox
has a sufficient amount of oil.
NEVER! disable or disconnect the
safety stop switch. It is provided for
NOTE
operator safety.Injury may result if it
is disable, disconnected or
improperly maintained.
3. If lubrication oil does not seep out as the drain plug is
being removed, fill with type ISO 680 (Whiteman P/N 10139)
gearbox lubricant oil until the oil filler hole overflows.
V-belt Check
A worn or damagedV-belt can adversely affect the performance
of the trowel.If aV-belt is defective or worn simply replace theV-
belt as outlined in the maintenance section of this manual.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — INITIAL START-UP
This section is intended to assist the operator with the initial
start-up of the walk-behind trowel. It is extremely important that
this section be read carefully before attempting to use the trowel
in the field.
CAUTION
The trowel is heavy and awkward to move
around. Use proper heavy lifting procedures
and DO NOT lift the trowel by the guard
rings.
DO NOT use your trowel until this section is thoroughly
understood.
LIFTINGTHETROWEL ONTOTHE SLAB.
Auxiliary Lifting Tube
DO NOT attempt to operate the trowel until
CAUTION
the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
Depending on engine manufacturer,
operating steps may vary. See engine
manufactures operating manual. The
following start-up procedure makes
reference to a HONDA 8 HP Engine
(Manual Start).
Removetheauxiliaryliftingtubelocatedontopofthemainhandle.
Insert the tube into the socket located on the opposite side of the
gearbox (Figure 20) from the handle.
Make sure that the hole in the tube engages with the pin in the
socket. With one person lifting from the main handle, and another
lifting from the auxiliary lifting tube pick up the machine to move
onto a slab.
Starting the Engine
1. Place the engine fuel valve lever (Figure 21) to the "ON"
position.
Figure 20. Lifting the Trowel
CAUTION
Figure 21. Engine FuelValve Lever
The trowel must be stabilized by the person
carrying the operator’s handle (Figure 20).
If it is not stabilized properly the handle may
swingaroundandflipthetrowel,thuscausing
damage to the trowel and bodily injury.
2. Move the throttle lever (Figure 22) to the "idle" position.
Lifting Bail (Option)
The lift bail is optional on new trowels. It provides an optimal lift
point for moving the trowel. Lift bails or forklift can be used to lift
a trowel up onto a building with a crane. See “Optional
Equipment” section in this manual for ordering information.
Using a crane to move a machine with a lift bail is highly
recommended, and is perfectly safe for the machine. Extra care
should be taken when lifting the machine off the ground, though.
Serious damage to the machine or personal injury could be
caused by dropping a trowel.
Figure 22. Throttle (Idle Position)
PAGE 24 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — INITIAL START-UP
6. If the engine has started, slowly return the choke lever
(Figure24)totheOPENposition.Iftheenginehasnotstarted
repeat steps 1 through 5.
3. Placethecentrifugalsafetystopswitch(Figure23)inthe
"ON"position.
7. Before the trowel is placed into operation, run the engine for
several minutes. Check for fuel leaks, and noises that would
associate with a loose guard ring and/or covers.
8. Test the Safety Stop Switch.
a. With the engine at idle, move the safety stop switch lever
to "OFF" (Figure 23). The engine should shut off.
b. CLEAR THE AREA AROUND THE TROWEL. Move
the safety stop switch lever back to the "ON" position,
restart the engine and let idle. Stand behind the handle
and spin the handle to the right, simulating a runaway
situation. (See Figure 26). Centrifugal force should
throw the safety switch outward to the "OFF" position
thus shutting off the engine.
Figure 23. Centrifugal Safety Stop Switch
4. Place the Choke Lever (Figure 24) in the "CLOSED "
position
Figure 24. Engine Choke Lever
5. Grasp the starter grip (Figure 25) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
.
Figure 26.Testing the Centrifugal Safety Stop Switch
9. To begin troweling, pull the throttle lever (Figure 27) toward
the "RUN" position.
Figure 25. Starter Grip
Figure 27. Throttle (Run Position)
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — OPERATION
Maneuvering the Trowel
The following steps are intended as a basic guide to machine
operation, and are not to be considered a complete guide to
concrete finishing. We suggest that all operators (experienced
and novice) read “Slabs on Grade” published by the American
Concrete Institute, Detroit, Michigan. Read the “Training”
section of this manual for more information.
1. Get into the operator’s position behind the handle. With a
secure foothold and a firm grasp on the handles slowly
increase the engine speed until the desired blade speed is
obtained.
2. To maneuver the trowel, gently lift up on or press down on the
main trowel handle. To move the machine to the operator’s
left, lift up on the handle, to move machine to the right, push
down on the handle.
PITCHINGTHE BLACES
Quick Pitch Handle
1. To pitch the blades upwards using the "Quick-Pitch™"
T-handle, (Figure 28) simply squeeze the trigger lock
and pull the T-handle towards the operator. Pushing
theT-handle towards the engine will cause the blades
to lay flat.
3. The best method for finishing concrete is to slowly walk
backwards (Figure 30) with the trowel, guiding the trowel
from side to side.This will cover all footprints on wet concrete.
4. Remember that if you let go of the trowel, just step away and
let the trowel come to a complete stop before trying to recover
the trowel. See (Figure 26) to see the area around the trowel
to keep clear of.
Figure 28. Quick-Pitch™ T- Handle
Standard Handle
1. To pitch the blades upwards using the "Standard" handle,
(Figure29)simplyturnthestar-wheelclockwise.Turningthe
starwheelcounterclockwise willcausethebladestolayflat.
Figure 29. Standard Handle
PAGE 26 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — OPERATION
Continue to practice maneuvering the trowel.Try to practice as if
you were finishing a slab of concrete. Practice edging and
covering a large area. Remember a good finishing technique is
to work backwards. Be careful when moving backwards so that
hazards can be avoided.The best way to get accustomed to the
trowel is repeated use.
(Figure 30) below illustrates a typical walk-behind trowel
application. Practice maneuvering the trowel.The trick is to let
the trowel do the work.
Figure 30. Maneuvering The Trowel
WARNING
WARNING
NEVER place your feet or hands inside the guard
rings while starting or operating this equipment.
ALWAYS keep clear of rotating or moving parts
while operating this equipment.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — OPTIONS
Clip-On Float Blades (Optional)
Blades
These blades will clip (Figure 33) on to an existing installed blade,
allowing your finisher to float on “wet” concrete so that the
troweling operation can begin as early as possible. They are
easily removable, so that after the floating operation, when the
concrete is sufficiently cured, they can be removed to expose the
finish blades for continued troweling.
Blades should be changed when
they fail to finish concrete in a
satisfactory manner.
NOTE
Blades are a vital part of finishing concrete. This trowel, or
finisher, has been designed to finish concrete and the blades are
built to stringent quality standards out of the finest trowel steel. If
you need replacement blades, consult your parts list in this
manual for part numbers and order them from your Multiquip parts
dealer or importer.
Figure 33. Clip-On Float Blade
Float Discs (Optional)
Combo Blades
This trowel was equipped with combination float/finish (Figure
31) blades as original equipment. These blades have been
designed for optimum performance in both the floating and
finishing operations. These blades are versatile and should take
care of most troweling needs.
These round discs (Figure 34) attach to the spiders and allow the
machine to “float” on “wet” concrete.The disc design allows early
floating and easy movement from wet to dry areas.They are also
very effective in embedding large aggregates and surface
hardeners.
Figure 31. Combination Blade
Finish Blades (Optional)
These blades (Figure 32) have been specifically designed for
finish operations with this trowel. They will provide a premium
surface finishing capability from your trowel.They should only be
used after the concrete has set to the point where the trowel does
not sink into the concrete when placed on it.
Figure 34. Float Disk
Figure 32. Finish Blade
PAGE 28 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — OPTIONS
Trowel Arm Adjustment Tool
Grinding Attachments
If blades show uneven wear patterns or some tend to wear out
faster than others, the trowel arms may need to be adjusted.
Whiteman makes a special tool (Figure 37) that will adjust all of
the trowel arms consistently.The Trowel Arm Fixture P/N is 1817.
Available grinding attachments are used for grinding surface
imperfectionsorjoints.Theseattachmentsallowgreaterutilization
of your trowel. (Figure 35) illustrates a typical grinding disk
assembly, complete with hub and stone mounting plate.
Figure 37.Trowel Arm Adjustment Fixture
Figure 35. Grinding Disk
Lifting Bail
There is a heavy duty, center balance type lifting bail (Figure 36)
made specifically for your trowel. These bails are ideal for lifting
and transporting your trowel.They are designed to lift the finisher
and balance it on it’s center of gravity, providing great stability
while lifting.This option is not available on electric trowel models.
Figure 36. Lifting Bail
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE (ENGINE)
Engine Maintenance
QP40TH — MAINTENANCE (ENGINE)
Perform engine maintenance procedures as referenced by
Table 4 below:
Table 4. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 30 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE (ENGINE)
DANGER :
Maintenance
Performtheenginemaintenanceproceduresasindicatedbelow:
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
spring box and bellows for oil leaks. Repair or replace as
needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 40.
WEEKLY
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
2. Tap the paper filter element (Figure 40) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 38), then adjust
the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 38. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 39.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten se-
curely.
Figure 40. Engine Air Cleaner
Figure 39. Engine Oil (Draining)
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE
Trowel Arm Adjustment Procedure
See the engine manual supplied with
your machine for appropriate engine
maintenance schedule and
troubleshooting guide for problems.
NOTE
The following procedure should be
followed to adjust trowel arms when
it becomes apparent that the trowel
is finishing poorly or in need of
routine maintenance.
NOTE
At the front of the book (Page 7) there is a “Daily Pre-Operation
Checklist ”. Make copies of this checklist and use it on a daily
basis.
A level, clean area to test the trowel prior to and after is essential.
Any unlevel spots in the floor or debris under the trowel blades
will give an incorrect perception of adjustment. Ideally, a 5 x 5"
three-quarter inch thick flat steel plate should be used for testing.
CAUTION!
ALWAYS allow the engine
to cool before servicing.
NEVER attempt any
maintenance work on a
hot! engine.
1. To determine which blades need adjustment, place the
trowelinthetestarea(three-quarterinchthickplate)andlook
for the following conditions:
■
Pitch the blades as flat as possible and look at the
adjustment bolts.They should all barely make contact
with the lower wear plate on the spider.If you can see
that one of them is not making contact, some adjustment
will be necessary.
MAINTENANCE SCHEDULE
Daily (8-10 Hours)
1. Check the oil level in the engine crankcase and gear box,
fill as necessary.
■
Is the machine wearing out blades unevenly (i.e. one
blade is completely worn out while the others look new)?
2. CheckV-belt.
Weekly (50-60 Hours)
(Figure 41) below illustrates a "worn spider bushings or bent
trowel arms". Check to see that adjustment bolt is barely
touching (0.10" max. clearance) lower wear plate. All alignment
bolts should be spaced the same distance from the lower wear
plate.
1. Relube arms, thrust collar and clutch.
2. Replace blades if necessary.
3. Check and clean or replace the engine air filter as
necessary.
4. Replace engine oil and filter as necessary, see engine
manual.
Monthly (200-300 Hours)
1. Remove, clean, reinstall and relube the arms and thrust
collar.Adjust the blade arms.
2. Remove, clean, reinstall clutch.
Figure 41. Worn Spider Plate
Yearly (2000-2500 Hours)
(Figure 42) below illustrates the "correct alignment " for a spider
plate (as shipped from the factory).
1. Check and replace if necessary the arm bushings, thrust
collar bushings and shaft seals.
2. Check pitch control cables for wear.
3. Adjust blade speed.
Figure 42. Correct Spider Plate Alignment
PAGE 32 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE
2. Start engine, and bring trowel blades up to full speed and look
forthefollowingconditions:
b. Loosen the jam nut and cone point square head set
screw,andcarefullylifttheuppertrowelassemblyoff
ofthespiderassembly. Aslighttapwitharubbermallet
maybenecessarytodislodgethespiderfromthemain
shaftofthegearbox.
■
Does the trowel have a perceived rolling or bouncing
motion when in use?
■
Look at the trowel while it is running, does the guard
ring “rock up and down” relative to the ground?
Trowel Arm Removal
1. Each trowel arm is held in place at the spider plate by a hex
headbolt (zerkgreasefitting)andarollpin.Removeboththe
hex head bolt and the roll pin (Figure 44) from the spider
plate.
Spider Removal
1. Onceitisdeterminedthatanadjustmentisrequired,remove
the spider assembly from the gearbox shaft as follows:
2. Remove the trowel arm from the spider plate.
a. Locate the cone point square head set screw (Figure 43)
and attached jam nut found on the side of the spider
assembly.
SPIDER
PLATE
ROLL
PIN
HEX HEAD
BOLT
(ZERK FITTING)
Figure 44. Removing Roll Pin
and Zerk Grease Fitting
3. Should the trowel arm inserts (bronze bushing ) come out
withthetrowelarm,removethebushingfromthetrowelarm
andsetasideinasafeplace.Ifthebushingisretained inside
the spider plate, carefully remove the bushing.
4. Examine the bronze trowel arm bushing insert (Figure 45),
clean if necessary.Replace bushing if out of round or worn.
Figure 45. Bronze Bushings
Figure 43. Spider/Gearbox Removal
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE
Trowel Blade Removal
3. If the trowel arm is found to be uneven or bent, replace the
trowelarm. Abenttrowelwillnotallowthetroweltooperate
in a smooth fluid rotation.
1. Removethetrowelbladesfromthetrowelarmbyremoving
thethreehexheadbolts(Figure46)fromthetrowelarm.Set
blades aside.
4. Next,checkeachofthesixsidesof theroundmachinedshaft
sectionofthetrowelarm.Eachsectionshouldhavethesame
clearance betweentheroundofthetrowelarmshaftandthe
testsurface.
HEX
HEAD
BOLT
Trowel arms can be damaged by
rough handling or by striking
exposed plumbing or forms while in
NOTE
REMOVE
operation. ALWAYS look-out for
objects which might cause damage
to the trowel arms.
LOCK
WASHER
BLADE
ARM
Trowel Arm Adjustment
Shown in (Figure 48) is the adjustment fixture with a trowel arm
inserted. As each trowel arm is locked into the fixture, the arm bolt
is adjusted to where it contacts a stop on the fixture. This will
consistently adjust all of the trowel arms, keeping the finisher as
flat and evenly pitched as possible.
Figure 46. Trowel Blades
2. Wirebrushanybuild-upofconcretefromallsixsidesofthe
trowel arm. Repeat this for the remaining three arms.
1. Locate the trowel arm adjustment tool P/N 1817. Set the
adjustmenttoolfora clock-wisebladerotation,meaningthe
fixture arm is in the "UP" position.
Trowel Arm FlatnessTest
1. Usingapieceof3/4inchthicksteelplateoranysurfacewhich
is true and flat, check all six sides of each trowel arm for
flatness.
2. Check each of the six sides of the trowel arm (hex section
only) using a ten thousands of an inch (max.) feeler gauge
(Figure 47) between the flat of the trowel arm and an ex-
tremelyflat testsurface.
Figure 47. Trowel Arm FlatnessTest
Figure 48. Trowel Arm AdjustmentTool
PAGE 34 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE
10. Reinstall lower wear plate, thrust collar and upper wear
ringinthereverse order thattheyweredis-assembledonto
the spider shaft. Make sure that there is little or no lateral
movement between the thrust collar and the spider shaft.
2. TrowelsmanufacturedpriortoJuneof1982requirethatthe
distancefromtheendoftheadjustingboltandthefixturearm
mustbe7/8"(Figure45).Conversely,trowelsmanufactured
after June of 1982 require that the distance from the end of
the adjusting bolt and the fixture arm must be 1/2".
11. Carefully lift the upper trowel assembly, line up the key-
wayongearboxmainshaftandinsertintospiderassembly.
3. Un-screwthelockingboltsontheadjustmenttool,andplace
thetrowelarmintotheadjustmentfixturechannelasshown
in (Figure 48). A thin shim may be required to cover the
bladeholesonthetrowelarm.Makesuretoalignthetrowel
adjustmentboltwiththefixtureadjustmentbolt.
12. Reinstall square head cone point into spider plate and
tighten in place.Tighten jam nut. Use care in making sure
point of set screw engages groove in gear box main shaft.
13. Lubricate all grease points (zerk fittings) with premium
"Lithum 12" based grease, conforming to NLG1 Grade #2
consistency.
4. Using an allen wrench, tighten the locking bolts on the
adjustment tool and securely lock the trowel arm in place.
Testing
5. Loosenthelockingnutonthetrowelarmlever,thenturnthe
trowel arm adjusting bolt until it barely touches (.010") the
adjusting bolt on the fixture.
1. Place trowel in test area, start engine and test trowel for
smoothness.
6. Afterthecorrectadjustmenthasbeenmade,tightenlocknut
on trowel arm lever to lock in place.
2. If trowel bounces has excessive vibration or does not run
smoothlyrepeatalignmentprocedure.
7. Loosen locking bolts on adjustment fixture, and remove
trowelarmfromfixture.
Changing a Blade
Whiteman recommends that all the blades be changed at the
same time.The machine may wobble or bounce if only some of
the blades are changed at one time.
8. Repeat steps 2-7 for the remaining trowel arms.
Re-Assembly
1. Place the machine on a flat, level surface. Adjust the blade
pitchcontroltomakethebladesasflataspossible.Notethe
blade orientation on the trowel arm.
1. Clean and examine the upper/lower wear plates and thrust
collar.Examine the entire spider assembly.Wire brush any
concreteorrustbuild-up.Ifanyofthespider componentsare
found to be damaged or out of round, replace them.
2. Makesurethatthebronzetrowelarmbushingisnotdamage
oroutofround.Cleanthebushingifnecessary.Ifthebronze
bushing is damage or worn, replace it.
Before removing the blades,
NOTE
please note the orientation of the
blade on the trowel arm.
3. Reinstall bronze bushing onto trowel arm.
4. Repeat steps 2 -3 for each trowel arm.
2. Remove the three bolts and lock washers that secure the
blade to the trowel arm. Remove the blade.
5. Makesurethatthespringtensionerisinthecorrectposition
to exert tension on the trowel arm.
3. Usingawirebrush,scrapeallconcreteparticles andforeign
debris from the trowel arm.
6. Insertalltrowelarmswithleversintospiderplate(withbronze
bushingalreadyinstalled)usingcaretoaligngreaseholeon
bronze bushing with grease hole fitting on spider plate.
4. Install the new trowel blade onto the trowel arm. Make sure
blade is installed correctly, maintaining the proper orienta-
tion for direction of rotation.
7. Lock trowel arms in place by tightening the hex head zerk
grease fitting and jam nut.
5. Reinstall the three bolts and lock washers that secure the
blade to the trowel arm.Tighten all three bolts securely.
8. Re-install the blades back onto the trowel arms.
9. Install stabilizer ring onto spider assembly.
6. Repeat steps 2-5 for all remaining blades.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — MAINTENANCE
ChangingThe V- Belt
1. Unscrew the two (2) t-bolts from the belt guard and remove
thelockwashers.(Figure49).
Figure 49. RemovingThe Belt Guard
2. Workbeltaroundandoffthebottompulleyandremovebelt.
3. Replace with the appropriate belt for your machine:
HPLA36 uses p/n 0261 (A-31)
HPHA36 uses p/n 0152 3 (A-28)
4. Placethebeltinthegrooveoftheupperpulleythenworkthe
belt over the bottom pulley into place.
The V-Belt will tension itself
automatically during operation. NO
FURTHER ADJUSTMENT OR
TENSIONING IS NECESSARY.
NOTE
5. Replacethebeltguard,lockwashers,andsecurewiththeT-
bolts.
WARNING!
NEVER operate equipment
with covers, or guards removed.
Keep fingers, hands, hair and
clothing away from all moving
parts to prevent injury.
PAGE 36 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 5. TROWEL TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Make sure that the safety switch is ON or replace switch if
necessary.
Safety switch malfunction?
Engine running rough or not at
all.
Look at the fuel system. Make sure there is fuel being supplied to
the engine. Check to ensure that the fuel filter is not clogged.
Fuel?
Check to ensure that the ignition switch has power and is
functioning correctly.
Ignition?
.
Bad contacts?
Replace switch.
Loose wire connections?
Check wiring. Replace as necessary.
Consult engine manufacturer’s manual.
Safety switch not functioning.
Other problems?
Make certain blades are in good condition, not excessively worn.
Finish blades should measure no less than 2" (50mm) from the
blade bar to the trailing edge, combo blades should measure no
less that 3.5" (89mm). Trailing edge of blade should be straight
and parallel to the blade bar.
Blades?
Check that all blades are set at the same pitch angle as
measured at the spider. A field adjustment tool is available for
height adjustment of the trowel arms (see Optional Equipment).
Spider?
Check the spider assembly for bent trowel arms. If one of the
arms is even slightly bent, replace it immediately.
Bent trowel arms?
If trowel “bounces, rolls
concrete, or makes uneven
swirls in concrete”.
Check the trowel arm bushings for tightness. This can be done by
moving the trowel arms up and down. If there is more than 1/8"
(3.2 mm) of travel at the tip of the arm, the bushings should be
replaced. All bushings should be replaced at the same time.
Trowel arm bushings?
Check the flatness of the thrust collar by rotating it on the spider.
If it varies by more than 0.02" (0.5 mm) replace the thrust collar.
Thrust collar?
Check the thrust collar by rocking it on the spider. If it can tilt
more than 3/32" (2.4 mm) [as measured at the thrust collar O.D.],
replace the bushing in the thrust collar.
Thrust collar bushing?
Thrust bearing worn?
Check the thrust bearing to see that it is spinning free. Note:
Thrust cap, replace if necessary.
The main output shaft of the gearbox assembly should be
checked for straightness. The main shaft must run straight and
cannot be more than 0.003" (0.08 mm) out of round at the spider
attachment point.
Main shaft?
Machine has a perceptible
rolling motion while running.
Check to make sure that both fingers of the yoke press evenly on
the wear cap. Replace yoke as necessary.
Yoke?
Check to ensure that each blade is adjusted to have the same
pitch as all other blades. Adjust per maintenance section in
manual.
Blade Pitch?
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — TROUBLESHOOTING (TROWEL)
TABLE 5. TROWEL TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Worn V-belts?
SOLUTION
Replace V-belt.
Dirty centrifugal clutch?
Disassemble and clean clutch.
Replace entire clutch.
Defective or worn out
centrifugal clutch?
Clutch slipping or sluggish
response to engine speed
change.
Rotate input shaft by hand. If shaft rotates with difficulty, check
the input and output shaft bearings. Replace as necessary.
Worn bearings in gearbox?
Worn or broken gears in
gearbox?
Verify that the gearbox shaft rotates when the input shaft is
rotated. Replace both the worm and worm gear as a set.
TABLE 6. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
PAGE 38 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — TROUBLESHOOTING (ENGINE)
TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Bleed (remove air) from fuel line.
Adjust carbureator float
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — EXPLANATION OF CODES
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 40 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — SUGGESTED SPARE PARTS
HPLA/HPHA-SERIES 36" TROWEL 1 TO 3 UNITS
WITH HONDA GX-240K1QA2 ENGINE.
1 to 3 Units
Qty...... P/N .................. Description
1 ......... 20478 .............. GRIP, LEFT
1 ......... 20463 .............. GRIP, RIGHT
2 ......... 20856 .............. SAFETY SWITCH
1 ......... 20285 .............. CABLE STANDARD HANDLE
1 ......... 20297 .............. CABLE QUICK-PITCH™
1 ......... 21172 .............. THROTTLE CABLE
1 ......... 21171 .............. THROTTLE
1 ......... 21173 .............. CABLE HOUSING
4 ......... 1157 A ............. BUSHING
4 ......... 1162 A ............. LUBE CAP
4 ......... 1167 A ............. SCREW
4 ......... 1456 ................ NUT
4 ......... 1875 ................ WASHER
4 ......... 1322 ................ SCREW
1 ......... 21046 .............. GASKET KIT
1 ......... 21047 .............. BEARING KIT
4 ......... 1247 ................ RUBBER GROMMET
4 ......... 1245 ................ SPACER
1 ......... 2827 ................ ARM (16-1/2")
2 ......... 0261 ................ BELT (A-31) (HPLA3648H)
2 ......... 0152 3 ............. BELT (A-28) (HPHA3548H)
1 ......... 10968 .............. THRUST COLLAR KIT
2 ......... 9807955846 ..... SPARK PLUG
2 ......... 17620ZH7023 .. TANK CAP
2 ......... 17210ZE2505 .. AIR CLEANER ELEMENT
2 ......... 17218ZE2505 .. FILTER OUTER
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — NAMEPLATE AND DECALS
NAMEPLATES AND DECALS
PAGE 42 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
2
PART NO.
1758
12405
PART NAME
QTY. REMARKS
DECAL: QUICK-PITCH™ HANDLE
DECAL: QUICK-PITCH™ HANDLE INSERT
DECAL: QUICK-PITCH™WARNING
1
2
1
3
20527
4
5
6
7
8
9
20526
2942
1736
1735
11246
DECAL: QUICK-PITCH™ LATCH WARNING
DECAL: MQ WHITEMAN 13"
DECAL: ARROWS
1
1
1
1
DECAL: PRE-LOAD INDICATOR
DECAL: OIL CHECK ............................................. 1 ....... PART OF DECAL KIT P/N 12620
NAMEPLATE.......................................................... 1 ....... CONTACT MULTIQUIP
.......................................................................................... SERVICE DEPT.
10
11
12
13
14
15
16
17
18
19
1940
11092
11246
1492
1147
11246
1261
1848
2938
11246
DECAL: MQ WHITEMAN (SMALL)
DECAL: CE
DECAL: GEAR DRIVE
DECAL: STANDARD HANDLE (FINISHER)
DECAL: HELMET, FOOT AND GLOVE ................. 1 ....... PART OF DECAL KIT P/N 12620
DECAL: HOT ......................................................... 1 ....... PART OF DECAL KIT P/N 12620
DECAL: DO NOT LIFT
DECAL: POWER TROWEL
DECAL: METRIC
1
1
1
1
PART OF DECAL KIT P/N 12620
1
1
1
DECAL: BELT DRIVE ........................................... 1 ....... PART OF DECAL KIT P/N 12620
SEE DECAL ILLUSTRATIONS ON PAGE 12
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — STANDARD HANDLE ASSY.
STANDARD HANDLE ASSY.
40
3
21
5
7
4
8
6
22
DETAIL “A”
9
10
14
18
17
43
16
42
15
12
3
19
20
44
2
SEE
DETAIL “B”
21
22
23
27
24
39
11
SEE
DETAIL “A”
1
13
30
25
26
31
ASM
41
32
38
37
28
1
36
45
35
29
33
2
DETAIL “B”
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
1
PART OF ENGINE ASSEMBLY.
34
2
PAGE 44 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — STANDARD HANDLE ASSY.
STANDARD HANDLE ASSY.
NO.
1
2
PART NO.
20463
20774
PART NAME
GRIP, HANDLE RIGHT
COVER, PAD HANDLE
QTY.
1
1
REMARKS
3
20818
DECAL, STD PITCH............................................1... .............. OBSOLETE ON LATER
.................................................................................................... MODELS
4
20817
0281
20282
0122C
3615
WHEEL, HAND HANDLE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
*
5
BEARING, THRUST, NICE 607
BEARING, TROWEL CONTROL
SCREW, SHS 3/8-16 X 1/2
COLLAR, SET 3/4 ID
SHAFT, TROWEL CONTROL
GRIP, HANDLE LEFT
HANDLE, ADJUSTABLE
THROTTLE
WHEEL ASSY., HAND
DECAL, CUSTOM 2 1/2 CHROME
SCREW, HHC 3/8-16 X 5.00
SCREW, BHC 1/4- 20 X 3/8 NYL PATCH, NP
SPACER, .360 X 17/64 X 1/8L
SLIDE BLOCK TROWEL CONTROL
CABLE ASSY., LENGTH 48.29” STD FINISHER
*
6
*
7
*
8
*
9
1478
*
10
20478
12556
21171
20439
1492
20438
0786
0786A
20287
20285
20856
1602
20988
20514
1662
20275
1118
20279
21017
1493
12567
2942
21173
20845
1116
11
12
13
14
15
16
17
18
19
20
INCLUDES ITEM W/■
SWITCH ASSY., SAFETY STOP ...........................1..................
■
21
SCREW, RHM 10-24 X 3/8
SCREW, FHSC PHILLIPS 8-32 X 1 1/4
WIRE ASSY., SAFETY STOP SWITCH
TIE, CABLE TY-RAP, BLACK
BLOCK, SUPPORT
PULLEY, SUPPORT BLOCK
PIN, SUPPORT BLOCK 3/8 X 1.59
SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD
SCREW, HHC 3/8-16 X 3 1/4
HANDLE, STD
DECAL, MQ WHITEMAN, 13”
HOUSING, CABLE 74”
SWIVEL, THROTTLE CABLE
NUT, BRASS JAM 5/16-18
NUT, NYLOC 3/8-16
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
22
23
24
25#
26#
27#
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
10133
20392
BRACKET, LIFT TUBE
HANDLE, LIFT ASSY. ............................................1.................. NO LONGER AVAILABLE
DECAL, CAUTION, LIFT HANDLE .........................1.................. NO LONGER AVAILABLE
BLOCK, CABLE ASSY. ..........................................1.................. INCLUDES ITEMS W/#
HAND WHEEL ASSY., PITCH CONTROL ..............1.................. INCLUDES ITEMS W/
HANDLE ASSY., STD FINISHERS ........................1.................. CONTACT SALES DEPT.
CABLE, CNTL 5/32 GALV AIRCRAFT 46.03"
CLEVIS, BALL END CONTROL CABLE
END-BOLT, CNTL CABLE
20280
20819
*
20301
20421
A8638
21172
1
1
1
1
CABLE, THROTTLE
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — QUICK-PITCH™ HANDLE ASSY.
QUICK-PITCH ™T-HANDLE
2
3
25
55
6
5
20
19
26
21
14
1
18
DETAIL “A”
22
58
4
60
24
10
25
23
SEE
DETAIL “A”
17
SEE
DETAIL
“B”
7
8
26
27
59
16
28
15
11
9
10
11
48
46
45
ASM
54
12
13
30
49
52
29
ASM
57
31
50
32
33
43
40
51
1
44
34
42
41
61
38
DETAIL “B”
39
56
47
37
2
35
36
53
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
1
2
PART OF ENGINE ASSEMBLY.
PAGE 46 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — QUICK-PITCH™ HANDLE ASSY.
QUICK-PITCH
™
HANDLE
NO.
1
2
3
4
5
6
7
PART NO.
20463
20774
20478
12556
20526
21171
20527
20389
1746
12405
1729
1706
20437
4568
1711
PART NAME
QTY.
1
1
1
1
1
1
1
1
1
2
3
1
1
1
1
REMARKS
GRIP, HANDLE RIGHT
COVER, PAD HANDLE
GRIP, HANDLE LEFT
HANDLE, ADJUSTABLE
DECAL, LATCHWARNING
THROTTLE
DECAL, Q.P. WARNING
HANDLE, QUICK-PITCH
TRIGGER, QP CHROMED
DECAL, WHITEMAN QUICK-PITCH
PIN, ROLL 3/16 X 1 1/4
SPRING, ENCLOSED QP CLAMP
PIN, QP LATCH
8
™
*
9
10
11
*
™
*
12
*
13
*
14
PIN, ROLL 3/16 X 1
SHAFT, CONTROL QP
15
16
17
18
1719
BUSHING, PIVOT PLATE
WHEEL ASSY., HAND
SCREW, HHC 3/8-16 X 5.00
PIN, ROLL 1/4 X 3/4
ARM, SLIDE CONTROL
CONNECTOR, QP CONTROL ARM
LINKAGE, QP CONTROL
PIN, ROLL 1/4 X 1 3/4
1
1
1
1
1
1
1
1
20439
20438
1731
20443
1709
20269
20276
20856
1602
20988
20514
20297
2942
1715
20270
1735
21017
1662
20275
1118
19+
20+
21+
22+
23+
24
■
SWITCH ASSY., SAFETY STOP ...........................1.................. INCLUDES ITEM W/
SCREW, RHM 10-24 X 3/8
■
25
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
26
27
28
29
30
31
32
33
34
35#
36#
37#
38
39
40
SCREW, FHSC PHILLIPS 8-32 X 1 1/4
WIRE ASSY., SAFETY STOP SWITCH
CABLE ASSY., QP CONTROL, 45”
DECAL, MQ WHITEMAN, 13”
SPRING, COUNTER BALANCE
BLOCK, QP ADJUSTMENT
DECAL, PRELOAD TRIM INDICATOR
SCREW, HHC 3/8-16 X 3 1/2 FULL THREAD
TIE, CABLE, TY-RAP BLACK
BLOCK, SUPPORT
PULLEY, SUPPORT BLOCK
PIN, SUPPORT BLOCK 3/8 X 1.59
SCREW, HHC 3/8-16 X 3 1/4
SNAP RING,TRUARC #5100-50
WASHER, 1/2 X 1/32, HARDENED
20279
1493
1737
1733
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — QUICK PITCH™ HANDLE ASSY.
QUICK PITCH HANDLE ASSY.
2
3
25
55
6
5
20
19
26
21
14
1
18
DETAIL “A”
22
58
4
60
24
10
25
23
SEE
DETAIL “A”
17
SEE
DETAIL
“B”
7
8
26
27
59
16
28
15
11
9
10
11
48
46
45
ASM
54
12
13
30
49
52
29
ASM
57
31
50
32
33
43
40
51
1
44
34
42
41
61
38
DETAIL “B”
39
56
47
37
2
35
36
53
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
1
2
PART OF ENGINE ASSEMBLY.
PAGE 48 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — QUICK PITCH™ HANDLE ASSY.
QUICK PITCH HANDLE ASSY.
NO.
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
PART NO.
1736
1718
1732
1717
12642
1758
20845
21173
PART NAME
QTY.
REMARKS
DECAL, ARROW
1
1
1
1
1
1
1
1
NUT, QP TRIM CTRL ADJ
BOLT, STRIPPER 3/8 X 1/2
SCREW, QP TRIM ADJUSTMENT
TUBE, MAIN HANDLE
DECAL, PATENT QP
SWIVEL, ENGINE THROTTLE CABLE
HOUSING, THROTTLE CABLE 74”
DECAL, CAUTION, LIFT HANDLE ............................... 1 ........... NO LONGER AVAILABLE
HANDLE, LIFT ASSY. .................................................. 1 ........... NO LONGER AVAILABLE
BRACKET, LIFT TUBE
NUT, NYLOC 3/8-16
NUT, BRASS JAM 5/16-18
TRIGGER, QP ASSY. .................................................. 1 ........... INCLUDES ITEMS W/
LINKAGE, QP CONTROL ASSY. ................................. 1 ........... INCLUDES ITEMS W/+
BLOCK, CABLE ASSY. ................................................ 1 ........... INCLUDES ITEMS W/#
HANDLE ASSY., MAIN. ............................................... 1 ........... CONTACT SALES DEPT.
CLEVIS, BALL END CONTROL CABLE
END-BOLT, CNTRL CABLE
CABLE, CNTL 5/32 GALV AIRCRAFT 43.19"
CABLE, THROTTLE
20392
10133
1116
20390
20293
20280
1
1
2
*
20421
A8638
20271
21172
1
1
1
1
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — 4-BLADE SPIDER ASSY.
4-BLADE SPIDER ASSY.
PAGE 50 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — 4-BLADE SPIDER ASSY.
4-BLADE SPIDER ASSY.
NO.
PART NO. PART NAME
QTY.
1
1
REMARKS
1
*
2
*
3
*
4
*
12208
12778
10793
1154A
1157A
0164B
1875
WEAR RING
FLANGE BEARING
THRUST COLLAR ............................................................. 1 ........... INCLUDES ITEMS W/#
WEAR PLATE
BEARING INSERT
1
4
4
4
4
8
8
4
4
4
4
4
1
4
1
1
4
5
%
6%
RADIUS HEAD 3/8- 16 x 1-1/4”
INT. SHKP. WASHER 3/8”
JAM NUT 3/8- 16
HHCS 5/16- 18 x 1-1/2”
LOCKWASHER 5/16”
LUBRA-CAP
TROWEL ARM EXTENDED, 16-1/2"
TROWEL ARM LEVER
ROLL PIN 5/16 x 1-3/4”
SPRING (RIGHT HAND)
SPIDER PLATE ONLY
RETAINING SCREW ASSY.
HEX NUT 3/8-16
7
%
8%
1876
9%
0105
10
11
12
13
14
15
16
17
18
19
20
21
%
%
%
%
%
%
%
%
%
%
%
0161C
1162A
2826
1163
4164
1316
1161
1322
1456
1167A
0166A
1215
SHSS 3/8-16 x 1-1/2” CONE POINT
LOCKWASHER 3/8”
SPIDER PLATE ASSY. ..................................................... 1 ........... INCLUDES ITEMS W/
THRUST COLLAR BUSHING
THRUST BEARING KIT .................................................... 1 ........... INCLUDES ITEMS W/
%
22 # 1471
1
*
23
10968
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GEARBOX & ENGINE MOUNTS ASSY.
GEARBOX & ENGINE MOUNTS ASSY.
1
2
1
36
12
13
37
8
3
35
38
4
5
4
34
6
7
11
9
7
6
14
2
10
15
16
17
18
32
31
30
19
6
G
I
0
Z
20
19
18
QTY. 1
GEARBOX REQUIRES
28 OZ. OF LUBRICATING
OIL FOR OPERATION.
33
32
GEARBOX ASSEMBLY
39
31
22
GASKET/SEAL KIT
BEARING KIT
40
41
21
23
24
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
5
1
APPLY SEALANT (LOCTITE
572 OR EQUIVALENT).
2
3
TORQUE TO 15 LB/FT.
25
26
SHIM AS NECESSARY
FOR 0.005 TO 0.010
INTPUT SHAFT ENDPLAY.
4
SHIM AS NECESSARY
FOR 0.000 TO 0.003
OUTPUT SHAFT ENDPLAY.
5
6
29
27
28
USE SPECIALLY FORMULATED
WHITEMAN GEARBOX LUBRICANT
P/N 10065 OR ISO 680 CYLINDER OIL.
3
PAGE 52 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GEARBOX & ENGINE MOUNTS ASSY.
GEARBOX & ENGINE MOUNTS ASSY.
NO.
PART NO.
0753
PART NAME
QTY.
1
4
1
1
1
1
1
1
1
2
2
1
1
1
1
1
3
2
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
4
4
1
REMARKS
1%
SEAL, OIL NATIONAL #470954
SCREW, HHC 1/4-20 X 3/4
FLANGE, INPUT SHAFT
*
2%
3%
4%
5%
0131A
12876
20395
20397
20398
20399
20400
20401
20466
20465
0627
RING, O -139 BUNA N
*
*
SHIM, INPUT 0.002 THICK
SHIM, INPUT 0.003 THICK
SHIM, INPUT 0.005 THICK
SHIM, INPUT 0.010 THICK
SHIM, INPUT 0.020 THICK
BEARING, CUP, TIMKEN #LM11910
BEARING, CONE, TIMKEN #LM11949
KEY, SQUARE 3/16 X 1-1/4
GEAR, WORM & SHAFT ASSY.
CASE, GEAR
6%#
7%#
8%
9%
1851
12874
1132
10%
11%
12
VENT, AIR
0655
SCREW, HHC 5/16-18 X 3/4
WASHER, FLAT 5/16 SAE
SCREW, HHC 1/4-28 X 3/8
SIGHT GLASS, 3/4 M PIPE STEEL
FITTING, PLUG 3/8 MP SQ HEAD
RING, SNAP,TRUARC 5100-112
BEARING, CUP TIMKEN #M86610
BEARING, CONE TIMKEN #M86647
GEAR, WORM, BRONZE
SHAFT, OUTPUT
KEY, WOODRUFF #21 HARDENED
KEY, WOODRUFF #25
SHIM, OUTPUT 0.002 THICK
SHIM, OUTPUT 0.003 THICK
SHIM, OUTPUT 0.005 THICK
SHIM, OUTPUT 0.010 THICK
SHIM, OUTPUT 0.020 THICK
RING, O -257 BUNA N
13
0300B
20476
21033
0121A
1138
14%
15%
16%
17%
18%# 20475
19%# 20474
20%
21%
22%
23
1140
20470
1139
1238
24%
20402
20403
20404
20405
20406
20396
12875
10235
1146
*
25%
26%
27%
28%
29%
*
COVER, GEARBOX
WASHER, C/S EXT. SHKP
SCREW, FHSC 5/16-18 X 1, NYLOC NP
SEAL, OIL, NATIONAL #470712
0254
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GEARBOX & ENGINE MOUNTS ASSY.
GEARBOX & ENGINE MOUNTS ASSY.
1
2
1
36
12
13
37
8
3
35
38
4
5
4
34
6
7
11
9
7
6
14
2
10
15
16
17
18
32
31
30
19
6
G
I
0
Z
20
19
18
QTY. 1
GEARBOX REQUIRES
28 OZ. OF LUBRICATING
OIL FOR OPERATION.
33
32
GEARBOX ASSEMBLY
39
31
22
GASKET/SEAL KIT
BEARING KIT
40
41
21
23
24
APPLY THREAD LOCK (LOCTITE
242 BLUE OR EQUIVALENT).
5
1
APPLY SEALANT (LOCTITE
572 OR EQUIVALENT).
2
3
TORQUE TO 15 LB/FT.
25
26
SHIM AS NECESSARY
FOR 0.005 TO 0.010
INTPUT SHAFT ENDPLAY.
4
SHIM AS NECESSARY
FOR 0.000 TO 0.003
OUTPUT SHAFT ENDPLAY.
5
6
29
27
28
USE SPECIALLY FORMULATED
WHITEMAN GEARBOX LUBRICANT
P/N 10065 OR ISO 680 CYLINDER OIL.
3
PAGE 54 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GEARBOX & ENGINE MOUNTS ASSY.
GEARBOX & ENGINE MOUNTS ASSY.
NO.
30
31
32
33
34
35
36
37
38
40
41
42
PART NO.
1150
20802
20803
20801
20797
1245
10700
1948
1247
PART NAME
QTY.
REMARKS
ARM, YOKE
1
2
2
1
1
4
1
1
4
RING, SNAP, TRUARC 5100-37 OR EQUIV.
SPACER, .50 OD X .40 ID X 0.25L
PIN, YOKE
STATIONARY GUARD RING
BUSHING, GUARD RING
FRONT ENGINE MOUNT
REAR ENGINE MOUNT
GROMMET 1/4 X .875 ID X 1-5/8 OD
20407
21046
21047
GEARBOX ASSY. ..................................................1.................. INCLUDES ITEMS W/%
GASKET/SEAL KIT ...............................................1.................. INCLUDES ITEMS W/
BEARING KIT ........................................................1.................. INCLUDES ITEMS W/#
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — ENGINE ASSY.
ENGINE ASSY.
PAGE 56 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — ENGINE HONDA ASSY.
ENGINE ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
1387
1391
0161C
0300B
20845
0310
1488
1475
1127
0740
0250
0261
152 3
1335
0181B
2577
1284
0166A
20982
1480
1949
1958
1245
1247
0252
0456
0251
0458
B1766
0855
0253
1868
ENGINE 8HP HONDA
HHCS 5/16-24 x 1-1/2"
LOCK WASHER 5/16"
FLAT WASHER 5/16"
1
4
4
4
1
1
1
1
2
3
4
5
6
7
8
9
SWIVEL, THROTTLE CABLE
SQUARE KEY 1/4X1/4X1.1/2"
WIRE, SAFETY SWITCH
CONNECTOR, SPLICE TAP
PULLEY, AK-66 X 3/4 .................................. 1 ..............HPLA3648H
PULLEY, AK-51 X 3/4 .................................. 1 ..............HPHA3648H
AUTOMATIC CLUTCH ASSY. ...................... 1 ..............INCLUDES ITEMS W/
BELT, A31 GATES HPII ONLY ..................... 1 ..............HPLA3648H
BELT, A28 GATES HPII ONLY ..................... 1 ..............HPHA3648H
9
10
11
11
12
13
14
15
16
17
18
19
20
21
22
*
BELT GUARD
LOCK WASHER 1/4"
T-BOLT 1/4-20
1
2
2
2
2
4
4
1
1
4
4
1
1
1
1
4
1
1
SCREW, HHC 3/8 - 16 X 1-1/2
WASHER, LOCK 3/8 MED
SCREW, FSCS 3/8 - 16 X 1-1/2
WASHER, CS EXT. SHKP 3/8
PLATE, REAR 8HP HONDA
PLATE, FRONT, 8HP HONDA
BUSHING, GUARD RING
GROMMET, 1/4 X 7/8ID X 1-5/8OD
SPINDLE 1" BORE
BEARING, SHIELDED
CLUTCH HOUSING DRUM
BUSHING, CLUTCH HSING DRM
WEIGHT, CLUTCH
23
*
24
*
25
*
26
*
27
*
28
*
SPRING
PLATE, CLUTCH EXPANSION
SCREW, SHS 3/8-24X3/4, NOPLT ............... 1 ..............REPLACES P/N 0457
LIFT STRAP ................................................ 1 ..............CONTACT UNIT SALES DEPT./ACC.
.......................................................................................ITEM
29
*
30
*
31
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GUARD RING ASSY.
GUARD RING ASSY.
2
1
PAGE 58 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — GUARD RING ASSY.
GUARD RING ASSY.
NO.
1
2
PART NO.
20808
1940
PART NAME
GUARD RING ASSEMBLY
DECAL
QTY.
1
1
REMARKS
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — BLADES & ARM ADJ. FIXTURE ASSY.
BLADES & ARM ADJUSTMENT FIXTURE ASSY.
PAGE 60 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — BLADES & ARM ADJ. FIXTURE ASSY.
BLADES & ARM ADJUSTMENT FIXTURE ASSY.
NO.
20
20
21
22
22
23
24
26
27
28
29
30
31
32
33
34
35
36
39
39
40
40
41
42
44
46
47
48
49
50
PART NO.
PART NAME
QTY. REMARKS
COMBO FLOAT & FINISH BLADE.................4........ CONTACT UNIT SALES DEPT./ACC.ITEM
ENDURO COMBO FLOAT &FINISH BLADE .4........ CONTACT UNIT SALES DEPT./ACC.ITEM
FLOAT BLADE...............................................4........ CONTACT UNIT SALES DEPT./ACC.ITEM
FINISH BLADE...............................................4........ CONTACT UNIT SALES DEPT./ACC.ITEM
ENDURO FINISH BLADE W/ROTATING ....... 4........ CONTACT UNIT SALES DEPT./ACC.ITEM
0202
0201
1434
1162A
7281
6014C
1237
0490
0487
0489
0488
HHCS 5/16-18X1" RING
GUARD RING LUG RING
TROWEL LUG (FINISH BLADE ONLY)
LUBRA-CAP
STABILIZER RING 14 1/2" ARM
HEX NUT 5/16-24
HHCS 5/16-18X7/8" NY-LOC
SHCS 7/16-14X1"
SHCS 3/8-16X1/2"
4
4
4
4
1
8
4
3
20
1
1
GRINDING DISC HUB
STONE MOUNT PLATE
GRINDING DISC STONE ONLY ....................1........ CONTACT UNIT SALES DEPT./ACC.ITEM
GRINDING DISC ASSY. .................................1........ CONTACT UNIT SALES DEPT./ACC.ITEM
UNIVERSAL COMBO BLADE ........................4........ CONTACT UNIT SALES DEPT./ACC.ITEM
ENDURO UNIVERSAL COMBO BLADE ....... 4........ CONTACT UNIT SALES DEPT./ACC.ITEM
UNIVERSAL FINISH BLADE ......................... 4 ....... CONTACT UNIT SALES DEPT./ACC.ITEM
ENDURO UNIVERSAL FINISH BLADE .........4........ CONTACT UNIT SALES DEPT./ACC.ITEM
UNIVERSAL MOUNTING BAR ...................... 4........ CONTACT UNIT SALES DEPT./ACC.ITEM
SNAP PIN 1/4"X1.3/4" ....................................8........ CONTACT UNIT SALES DEPT./ACC.ITEM
0166A
1723
LOCKWASHER 3/8"
4
TROWEL ARM ADJ.FIXTURE ASSY. ............1........ CONTACT UNIT SALES DEPT./ACC.ITEM
REVERSIBLE COMBO BLADE ...................... 4........ CONTACT UNIT SALES DEPT./ACC.ITEM
MALE R.H. ROD END 5/16"
1
FLOAT DISC ..................................................1........ CONTACT UNIT SALES DEPT./ACC.ITEM
FLOAT DISC LATCH PIN ............................... 4........ CONTACT UNIT SALES DEPT./ACC.ITEM
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — LIFTING BAIL ASSY. (OPTION)
LIFTING BAIL ASSY. (OPTION)
PAGE 62 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HPLA/HPHA-SERIES 36"TROWEL — LIFTING BAIL ASSY. (OPTION)
LIFTING BAIL ASSY. (OPTION)
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
LIFTING BAIL ASSY. ...........................1............ CONTACT UNIT SALES DEPT./ACC.ITEM
2
3
10229
0161C
HHCS 5/16-24X1"
LOCKWASHER 5/16"
4
4
4
LIFTING BAIL ASSY. ...........................1............ CONTACT UNIT SALES DEPT./ACC.ITEM
5
6
7
0205
1394
0166A
HHCS 3/8-16X1"
FHSCS 3/8-16X1"
LOCKWASHER 3/8"
3
1
3
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 64 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
PART NO.
PART NAME
QTY.
REMARKS
16271ZE2000
17210ZE2822
17218ZE2505
17231ZH9820
17232891000
17238ZE2310
17239ZE1000
17410ZE2020
90325044000
90009ZE2003
9405006000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER, DUAL ............. 1 ............. INCLUDES ITEMS W/
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
*
3
*
5
1
1
1
2
1
6
8%
9%
10
13
14
15
ELBOW COMP., AIR CLEANER ............... 1 ............. INCLUDES ITEMS W/
%
WINGNUT, TOOL BOX SETTING
BOLT- WASHER 6 X 22
NUT, FLANGE 6MM
2
1
2
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 66 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
14100ZE2W01
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEMS W/
*
ROD PUSH
ARM VALVE ROCKER
LIFTER VALVE
PIVOT ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, IN.
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
VALVE, EX.
SPRING, VALVE
9
10
11
12
13
14
15
RETAINER, IN. VALVE SPRING
RETAINER, EX. VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 68 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
+ 16010ZE2812
16011ZA0931
16013ZA0931
16016ZHW01
16024ZE1811
16028ZE0005
16028ZE2005
16100ZE2W71
16124ZE0005
16166ZE2W70
16172ZE3W10
16173001004
16211ZE2000
16220ZA0702
16221ZA0800
16223ZA0800
16610ZE1000
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
PART NAME
QTY.
REMARKS
1
2
3
5
%
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
1
1
1
1
*
*
*
*
SCREW SET
6 +
SCREW SET, DRAIN
SCREW SET B
CHOKE SET
CARBURETOR ASSY................................ 1 ............. INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
COLLAR, SET
O-RING
INSULATOR, CARBURETOR
SPACER COMP., CARBURETOR
GASKET, CARBURETOR
GASKET, INSULATOR
LEVER COMP., CHOKE, STD. ................. 1 ............. INCLUDES ITEMS W/
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6
PIN, SPRING 2 X 12
JET, MAIN #82, OPTIONAL
JET, MAIN #85, OPTIONAL
JET, MAIN #88
JET SET, PILOT #40 ................................. 1 ............. INCLUDES ITEMS W/
CHAMBER SET, FLOAT ............................ 1 ............. INCLUDES ITEMS W/+
*
7
8
*
*
9
*
10
1
1
1
1
1
1
1
1
*
11
*
12
*
13
*
14
15
16
17
18
■
19
1
1
1
1
1
2
1
1
1
1
*
20
*
21
*
22
*
23
24
25
26
26
*
■
99101ZH80820
99101ZH80850
99101ZH80880
99204ZE20400
16015ZE8005
26
*
27
*
%
28
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 70 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
1
2
3
4
5
8
PART NO.
PART NAME
QTY.
REMARKS
16550ZE2700
16551ZE2000
16555ZE2000
16561ZE2000
16562ZE2000
16570ZE2W20
16571ZE2W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16581ZE2W00
16584883300
16592883310
90013883000
90015ZE5010
90114SA0000
93500050280A
93500050160A
9405006000
ARM, GOVERNOR
ARM, GOVERNOR
ROD, GOVERNOR
1
1
1
1
1
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSY., REMOTE ...................... 1............. INCLUDES ITEMS W/
LEVER, CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE COMP., CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6 X 12 CT200
BOLT, GOVERNOR ARM
NUT, SELF-LOCK 6MM
SCREW, PAN 5 X 28
*
10
1
1
1
1
1
1
1
1
2
1
1
1
1
1
*
11
*
12
*
13
*
14
*
15
*
16
*
17
19
*
20
21
24
*
26
*
SCREW, PAN 5 X 16
NUT, FLANGE 6MM
27
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 72 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
QTY.
REMARKS
11400ZE2601
11381ZE2801
15600ZG4003
15600735003
15625ZE1000
15625ZE1003
16510ZE2811
COVER ASSY., CRANKCASE .................. 1 ............. INCLUDES ITEMS W/
*
GASKET, CASE COVER
CAP ASSY., OIL FILLER .......................... 1 ............. INCLUDES ITEMS W/
CAP ASSY., OIL FILLER .......................... 1 ............. INCLUDES ITEMS W/+
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
GOVERNOR ASSY., BALANCER ............. 1 ............. INCLUDES ITEMS W/$
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
WASHER 6 X 16
CLIP, GOVERNOR HOLDER
PIN, DOWEL 8 X 12
OIL SEAL 30 X 46 X 8
WASHER, PLAIN 6MM
BOLT, FLANGE 8 X 35
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6206
1
%
8+
1
1
9%
10
*
11 $ 16511ZE2000
2
1
2
1
1
1
2
1
1
7
1
*
12 $ 16512ZE2811
*
13 $ 16513ZE2000
*
14
15
16
17
18
19
20
21
22
16531ZE2000
90473147000
90602ZE1000
90701HC4000
91201890003
9410106800
957010803500
961006202000
961006206000
*
*
*
*
*
*
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 74 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
2
8
PART NO.
PART NAME
QTY.
REMARKS
13320ZE2601
13351ZE2010
90745ZE2600
961006206000
CRANKSHAFT COMP., Q- TYPE.............. 1 ............. INCLUDES ITEMS W/
*
WEIGHT, BALANCER
KEY 6.3 X 6.3 X 43
BEARING, RADIAL BALL 6206
1
1
1
10
12
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 76 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
3
6
7
PART NO.
PART NAME
QTY.
REMARKS
12000ZE2834
16541ZE2010
90131896650
90446KE1000
91201890003
9410912000
9425110000
961006202000
90013883000
34150ZH7003
CYLINDER ASSY., BALANCER + OIL ALERT ...... 1 .......... INCLUDES ITEMS W/
*
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER 8.2 X17X0.8
OIL SEAL 30X46X8
WASHER, DRAIN PLUG 12MM
PIN, LOCK 10MM
BEARING, RADIAL BALL 6202
BOLT, FLANGE 6X12 CT200
ALERT UNIT, OIL
1
2
1
1
2
1
1
1
1
8
11
12
*
14
15
16
*
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 78 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12200ZH9000
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE2800
12310ZE2020
12391ZE2020
14775ZE2010
90014ZE2000
90042ZE2000
92900080320E
90441ZE2010
9430112200
CYLINDER HEAD COMP. ....................................... 1 .......... INCLUDES ITEMS W/
*
2
*
3
*
4
*
5
6
7
GUIDE, VALVE, OS, OPTIONAL
GUIDE, EX. VALVE, OS, OPTIONAL
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER COMP., HEAD
GASKET, CYLINDER HEAD COVER
SEAT, VALVE SPRING
BOLT, HEAD COVER
BOLT, STUD 8X123
BOLT 2, STUD 8X32
WASHER COMP., HEAD COVER
PIN A, DOWEL 12X20
BULK HOSE, VACUUM 11X1000, 11X100
BOLT, FLANGE 10X80
1
1
1
1
1
1
1
1
2
2
1
2
1
4
1
1
1
1
8
10
11
12
13
14
15
16
17
17
17
17
950051100130M
957011008000
9807955846
9807955855
9807956846
SPARK PLUG, BPR5ES, NGK
SPARK PLUG, W16EPR-U, DENSO, OPTIONAL
SPARK PLUG, BPR6ES, NGK
SPARK PLUG, W20EPR-U, DENSO
9807956855
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 80 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
4
5
7
9
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE2010ZC
19631ZE2D00
32197ZH8003
36100ZH7003
90013883000
90684ZA0601
CLIP, TUBE
1
1
1
1
1
6
1
COVER COMP., FAN *NH1* BLACK
SHROUD
SUB-HARNESS
SWITCH ASSY., ENGINE STOP
BOLT, FLANGE 6X12, CT200
CLIP, WIRE HARNESS
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 82 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
7
PART NO.
PART NAME
QTY.
REMARKS
19511ZE2000
28450ZE2W11
31100ZE2010
90201ZE3V00
90741ZE2000
FAN, COOLING
1
1
1
1
1
PULLEY COMP., STARTER, SCREEN GRID
FLYWHEEL COMP.
NUT, SPECIAL 16MM
8
KEY, SPECIAL WOODRUFF 25X18
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 84 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
6
*
8
11
12
13
14
15
PART NO.
PART NAME
RUBBER SUPPORTER 107MM
JOINT, FUEL TANK
TANK COMP., FUEL *NH1*, BLACK
CAP COMP., FUEL FILLER .................................... 1 .......... INCLUDES ITEMS W/
GASKET, FUEL FILLER CAP
FILTER, FUEL
O-RING 14MM, ARAI
NUT, FLANGE 8MM
BULK HOSE, FUEL 4.5X3000, 4.5X222
CLIP, TUBE, B8
BOLT, FLANGE 8X25
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE2020ZD
17620ZH7023
17631ZH7003
17672ZE2W01
91353671003
9405008000
1
1
1
*
1
1
1
2
1
2
2
950014500360M
9500202080
957010802500
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 86 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
6
8
PART NO.
PART NAME
QTY.
REMARKS
30500ZE2023
30700ZE1013
31512ZE2000
36101ZE1010
90015883000
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
GROMMET, WIRE
1
1
1
1
2
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6X28
11
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 88 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
7
8
10
11
12
13
14
PART NO.
PART NAME
QTY.
REMARKS
18310ZE2W00
18320ZE2W01
18323ZE2W00
18330ZE2W00
18331ZE2810
18333ZE3800
18355ZE2010
18381ZE2W10
90013883000
90050ZE1000
90055ZE1000
90050ZE1000
9405008000
MUFFLER COMP.
1
1
1
1
1
1
1
1
1
6
3
1
5
PROTECTOR COMP., MUFFLER
PROTECTOR, EX. PIPE
PIPE, EX.
CAP, MUFFLER
GASKET, EX. PIPE
ARRESTER, SPARK
GASKET, MUFFLER, ARRESTER
BOLT, FLANGE 6X12 CT200
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
SCREW, TAPPING 5X8
NUT, FLANGE 8MM
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 90 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.
PART NAME
QTY.
REMARKS
13010ZE2013
13011ZE2013
13012ZE2013
13013ZE2013
13101ZE2W00
13102ZE2W00
13103ZE2W00
13104ZE2W00
13111ZE2000
13200ZE2000
13200ZE2305
90001ZE8000
90551ZE1000
RING SET, PISTON, STD.
RING SET, PISTON, OS 0.25, OPTIONAL
RING SET, PISTON, OS 0.50, OPTIONAL
RING SET, PISTON, 0.75, OPTIONAL
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25, OPTIONAL
PISTON, OS 0.50, OPTIONAL
PISTON, 0.75, OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING STANDARD ................ 1 ..........INCLUDES ITEMS W/
ROD ASSY., CONNECTING, US 0.25, OPT. .......... 1 ..........INCLUDES ITEMS W/
*
*
BOLT, CONNECTING ROD
CLIP, PISTON PIN 18MM
2
2
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 92 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZE2W01ZB
28410ZE2W01ZB
28421ZE2W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28461ZE2W02
28462ZE2W11
90004ZE2W01
90008ZE2003
STARTER ASSY., RECOIL *NH1*, BLACK ................... 1 .......INCLUDES ITEMS W/
*
2
CASE COMP., RECOIL STARTER *NH1*, BLACK
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING RATCHET
RETAINER, SPRING
GRIP, STARTER
ROPE, RECOIL STARTER
SCREW, CENTER
BOLT, FLANGE 6X10
1
1
2
1
1
2
1
1
1
1
3
*
3
*
4
*
5
*
6
*
7
8
*
*
10
*
11
*
13
*
14
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — ENGINE LABELS
ENGINE LABELS
PAGE 94 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX240K1QA2 ENGINE — ENGINE LABELS
ENGINE LABELS
NO.
1
3
5
16
PART NO.
PART NAME
EMBLEM, INTERNAL
LABEL, CAUTION
MARK, CHOKE, EXTERNAL
MARK, OIL ALERT, E
QTY.
REMARKS
87521ZE2W01
87522ZH9000
87528ZE2810
87532ZH8810
1
1
1
1
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 96 — HPLA/HPHA-SERIES 36" WALK-BEHINDTROWEL— OPERATION AND PARTS MANUAL — REV.#3 (07/06/10
)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
HPLA/HPHA-SERIES 36" WALK-BEHIND TROWEL — OPERATION AND PARTS MANUAL — REV. #3 (07/06/10) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Mayco Parts
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Fax: 310-631-5032
Service Department
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: 0161 339 3226
Global Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2010, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miller Electric Welder INTEGRA 201 241 User Manual
Milwaukee Photo Scanner SM105 User Manual
MTD Chipper 246 641A000 User Manual
NEC Flat Panel Television x463un User Manual
NETGEAR Switch GSM7328S User Manual
Nexus 21 Water Pump 3 User Manual
NordicTrack Treadmill a2550 pro User Manual
Panasonic Power Supply IMC80A User Manual
Panasonic Switch AJ9 J9 User Manual
Pass Labs Speaker SR 1 User Manual