OPERATION AND PARTS MANUAL
Tamping Rammer
Model
MTR-40HS
Revision #2 (12/15/03)
MULTIQUIPINC.
18910 WILMINGTON AVE.
PARTS DEPARTMENT:
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MTR-40HS Tamping
ROBIN EC-08HS ENGINE
Crankcase and Cylinder Assembly ................... 42-43
Crankshaft and Piston Assembly ...................... 44-45
Governor Assembly .......................................... 46-47
Muffler Assembly .............................................. 48-49
Carburetor and Oil Pump Assembly ................. 50-51
Recoil Starter & Blower Housing Assembly ..... 52-53
Air Cleaner Assembly........................................ 54-55
Carburetor Components Assembly .................. 56-57
Recoil Starter Components Assembly .............. 58-59
Magneto Assembly ........................................... 60-61
Rammer
Here's How To Get Help ............................................3
Table Of Contents .....................................................4
Parts Ordering Procedures .......................................5
Safety Message Alert Symbols ............................. 6-7
Rules For safe Operation ..................................... 8-9
Operation and Safety Decals ..................................10
General Information ................................................11
Specifications ..........................................................12
Controls and Components ......................................13
Basic Engine ...........................................................14
Pre-Inspection .........................................................15
Initial Start-Up ................................................... 16-17
Operation ................................................................18
Maintenance (Rammer) .................................... 19-20
Maintenance (Engine).............................................21
Troubleshooting Guide ...................................... 22-23
Explanation Of Codes In Remarks Column ............24
Terms and Condition of Sale — Parts ......................... 62
Suggested Spare Parts ...........................................25
Name Plate and Decals .................................... 26-27
Crankcase and Engine Assembly ..................... 28-29
Guide Cylinder Assembly.................................. 30-31
Tank and Handle Assembly .............................. 32-35
Foot Assembly .................................................. 36-37
Narrow Foot Assembly (Option) ....................... 38-39
Trench Shoe Assembly (Option) ....................... 40-41
PAGE 4 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Extra Discounts!
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Mayco Parts
800-306-2926
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Ordered
via
Standard
orders
Stock orders
($750 list and above)
Service Department
800-478-1244
310-537-3700
Fax:310-537-4259
Fax
3%
5%
10%
10%
Web
MQ Power Service Department
800-835-2551
310-537-3700
Fax:310-638-8046
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
Technical Assistance
800-478-1244
Fax:310-631-5032
Fax:310-537-1173
Warranty Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
No other allowances on freight shipped by any other
carrier.
Multiquip’s Main Phone Numbers
NOTE:DISCOUNTSARESUBJECTTOCHANGE
800-421-1244
310-537-3700
Fax:310-537-3927
MULTIQUIP INC.
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
18910 WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700•800-421-1244
FAX:310-537-3927
WWW:multiquip.com
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Engine exhaust gases contain poisonous
This Owner's Manual has been
developed to provide complete
instructions for the safe and
efficient operation of the Multiquip
MTR-40HS Tamping Rammer.
Refer to the engine manufacturer's
instructions for data relative to its
safe operation.
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
Before using this Rammer,
ensure that the operating
individual has read and
understands all instructions in
this manual.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with the MTR-40HS Tamping
Rammer operation will be referenced with Hazard Symbols
which appear throughout this manual, and will be referenced in
conjunction with Safety Message Alert Symbols.
PAGE 6 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR40-HS — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position, and remove the ignition key
when the machine is not in use.
ALWAYS wear approved respiratory
protection.
Sight and Hearing hazard
Over Speed Conditions
NEVER tamper with the factory settings of
the engine governor or settings. Personal
injury and damage to the engine or
equipment can result if operating in speed
ranges above maximum allowable.
ALWAYS wear approved eye and
hearing protection.
Equipment Damage Messages
This rammer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
Other important messages are provided throughout this manual
to help prevent damage to your rammer, other property, or the
surrounding environment.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
the rammer.
DANGER:
Failure to follow instructions in this manual
may lead to serious injury or even death!This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
The following safety guidelines should always be used when
operating the MTR-40HSTamping Rammer:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot! components can cause serious burns.
SAFETY
■
DO NOT operate or service this equipment
before reading this entire manual.
The engine of this rammer requires an adequate free flow of
cooling air. NEVER operate the rammer in any enclosed or
narrow area where free flow of
■
■
This equipment should not be operated by
persons under 18 years of age.
the air is restricted. If the air flow
is restricted it will cause
serious damage to the
rammer's engine and may
NEVER operate the rammer without proper protective clothing,
shatterproof glasses, steel-toed boots and other protective
devices required by the job.
cause injury to people.
Remember the rammer's
engine gives off DEADLY
carbon monoxide gas.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool.
NEVER operate the rammer under the
influence or drugs or alcohol.
■
NEVER smoke around or near the machine.
Fire or explosion could result from fuel
vapors, or if fuel is spilled on a hot! engine.
■
■
ALWAYS check the rammer for loosened threads or bolts
before starting.
ALWAYS wear proper respiratory (mask), hearing and eye
■
■
NEVER operate the rammer in an explosive atmosphere or
near combustible materials. An explosion or fire could result
causing severe bodily harm or even death.
Topping-off to filler port is dangerous, as it tends to spill fuel.
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — RULES FOR SAFE OPERATION
■
NEVER use accessories or attachments, which are not Maintenance Safety
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
NEVER lubricate components or attempt service on a running
rammer.
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
ALWAYS allow the rammer a proper amount of time to cool
before servicing.
NEVER Run engine without air filter. Severe engine may
occur. Service air filter frequently to prevent carburetor
malfunction.
■
■
Keep the rammer in proper running condition.
Fix damage to the rammer immediately and always replace
broken parts.
■
■
AVOID wearing jewelry or loose fitting clothing that may snag
on the controls or moving parts, this can cause a serious
injury.
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
DO NOT use food or plastic containers to dispose of
hazardous waste.
ALWAYS check to make sure that the operating area is clear
before starting the engine.
■
■
NEVER leave the machine unattended while running.
Emergencies
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using rammer.
■
ALWAYS know the location of the nearest fire extinguisher.
■
■
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
Refer to the ROBIN Engine Owner's Manual for engine
technical questions or information recommended by Multiquip
for this equipment. Damage to the equipment and/or injury to
user may result.
■
■
ALWAYS know the location of the nearest and first aid kit.
Transporting
■
ALWAYS shutdown engine before transporting.
■
Tighten fuel tank cap securely and close fuel cock to prevent
fuel from spilling.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
■
■
Drain fuel when transporting rammer over long distances or
bad roads.
When placing the rammer inside a truck-bed for transport,
always tie-down the rammer.
ALWAYS use proper lifting techniques when moving the
rammer.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — OPERATION AND SAFETY DECALS
PAGE 10 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — GENERAL INFORMATION
Definition of Tamping Rammer
The Mikasa MTR-40HS Tamping Rammer is a powerful
compacting tool capable of applying a tremendous force in
consecutive impacts to a soil surface. Its applications include
soil compacting for backfilling for gas pipelines, water pipelines
and cable installation work.
The impact force of the MTR-40HS levels and uniformly
compacts voids between soil particles to increase dry density.
Circular motion is converted to create impact force.The MTR-
40HS tamping rammer develops a powerful compacting force at
the foot of the rammer.To maintain optimum performance, proper
operation and service are essential.
Construction of Tamping Rammer
The Mikasa MTR-40HS is equipped with a Robin air cooled, oil-
injected two cycle gasoline engine. Transmission of the power
takes place by increasing the engine speed to engage the
centrifugal clutch.
Rammer Gearbox and Spring Cylinder
The Mikasa MTR-40HS uses an oil bath lubrication system.
Always check the oil level through the oil level sight glass at the
rear of the tamper foot.
Controls
Before starting the MTR-40HS Tamping Rammer identify and
understand the function of the controls, see Figure 1 on page13.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — SPECIFICATIONS
Table1. MTR-40HS Rammer Specifications
MODEL
Overall Height
Overall Width
Over Length
Shoe Size
MTR-40HS U.S. (metric)
43.7 in. (1,110 mm)
13.8 in. (351 mm)
24.5 in. (622 mm)
5.9 x 10.6 in. (150 x 270 mm)
600 ~ 690
Blows/minute
Tamping Area
Impact Force
Clutch
1,445 sq. ft. per hr (134 sq.m per hr)
1,100 - 1,225 lbs./blow ( 500 - 550kg/blow)
Automatic Centrifugal
Operating Weight
97 lbs. (44 kg)
Table 2. ROBIN EC-08HS Engine Specifications
Model
ROBIN EC08HS
Air-Cooled 2 Stroke Gasoline Engine
1-31/32 in. x 1-7/32 in. ( 50 mm x 40 mm)
5.12 cu.in. (78.5 cc)
Type
Bore x Stroke
Piston Displacement
Compression Ratio
Continuous Rated Output
Max. Output
6.5 : 1
1.8 hp/ 4,000 rpm
3.3 hp/5,500 rpm
Engine
Max. Torque
3.7 ft-lb/3,600 rpm (0.551 Kg-m/3,600 rpm)
Air-Cooled By Fan
Cooling System
Lubrication System
Fuel Consumption
Fuel
Fuel-Lubrication Oil Spraying System
0.84 lb/hp/h (2.2hp/4,500 rpm)
Gasoline
Spark Plug
NGK B-6HS
Starting System
Recoil Starter
11 x 9.75 x 12 in.
280 x 248 x 305 (mm.)
Dimension (L x W x H)
Dry Net Weight
17 lbs. (7.7 Kg.)
pecifications are general and are subject to change without notice. If exact
easurements are required, equipment should be weighed and measured.
PAGE 12 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— CONTROLS AND COMPONENTS
Figure 1. MTR-40HS Rammer
Figure 1 shows the location of the controls and components
for the MTR-40HS Tamping Rammer.The functions of each
control is described below:
8. Fuel Tank/Cap – Remove this cap to add unleaded
gasolinetothefueltank.Makesurecapistightenedsecurely.
DO NOT over fill.
1. Throttle Lever – Used to adjust engine speed (rpm).
Move lever forward (SLOW) to reduce engine speed,
move lever back toward operator (FAST) to increase
speed.
WARNING
Adding fuel to the tank should be accomplished only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel spill,
DO NOT attempt to start the engine until the fuel
residue has been completely wiped up, and the area surrounding
the engine is dry.
2. Fuel Shut-OffValve – Supplies fuel from the fuel tank to
theengine.Tobeginfuelflowmovethefuelshut-offvalve
downward.
3. Primary Air Cleaner – Pre-cleans (first stage) dirt and
other debris from entering the engine.
9. Oil Tank/Cap – Remove this cap to add 2-stroke
outboard motor oil to the oil tank. Make sure cap is
tightened securely. DO NOT over fill.
4. Foot– Laminated wood with tempered steel plate for
superior shock absorption.
5. Grip – Whentransportingtherammer, carryitbygriping
10. Engine Air Cleaner – Prevents dirt (second stage) and
the handle.
other debris from entering the engine.
6. Nameplate– Displaysinformationregardingtherammer.
11. Dust Sleeve – Prevents dust and debris from entering
7. Handle – To operate rammer GRIP handle assembly
into the spring cylinder.
firmly on both sides.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — BASIC ENGINE
3
4
2
1
5
6
Figure 2. Engine Controls and Components
INITIAL SERVICING
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
5. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
6. Muffler – Used to reduce noise and emissions.
1. Secondary Air Cleaner – Prevents dirt and other debris
from entering the fuel system. Remove wing-nut on top of
air filter cannister to gain access to filter element.
2. Choke Lever –Used when starting the engine. Normally
used in cold weather conditions. In cold weather turn the
choke lever to the fully closed position, in warm weather
set choke lever half way or completely open.
WARNING
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
3. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch). Clean
spark plug once a week.
4. Engine ON/OFF Switch – Controls the starting and
stopping of the engine. Switch must be in the "ON" position
when starting the engine.
PAGE 14 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— PRE-INSPECTION
This section is intended to assist the
operator with the pre-inspection of
the MTR-40HS Tamping Rammer. It
is extremely important that this section
be read carefully before attempting
to operate the rammer.
Fuel
1. Thisrammerisequippedwithatwo-cycledgasolineengine.
Useonlyunleadedgasoline. Hightestethylgasolineisnot
recommended.
2. Iffuelislow, removethefuelfillercap(Figure4)andfillwith
only unleaded gasoline. Motor fuels are highly flammable
andcanbedangerousifmishandled.DONOTsmokewhile
refueling. DO NOT attempt to refuel the pump if the engine
is hot! or running.
DO NOT use your rammer until this section is thoroughly
understood.
Inspection
■
■
■
Check all nuts, bolts fasteners for tightness. Retighten as
necessary.
Clean any dirt from the recoil starter and engine cooling fins.
Wipe the entire rammer clean before operating.
Replace any missing or damaged Safety Operation decals.
CAUTION:
Failure to understand the operation of the MTR-
40HSTamping Rammer could result in severe
damage to the rammer or personal injury.
Figure 4. Fuel Tank
Prior to Operation
Engine Oil Check
1. When transporting the machine, carry it by the grip handle
located on the body (Figure 3).
1. Check the engine oil level at the sight gauge located on the
operator's side of the oil tank (Figure 5). Fill the oil tank to
the"H"levelusingonlyoutboard(2-stroke)oil. Replenishthe
oil regularly before the oil level reaches the "L" level of the
oil tank.
2. Makesuretheoilhoseisnotpinched orsqueezed. Asensor
detectslackofoilandshutsdowntheengineautomatically.
3. Remember low levels of engine oil may result in engine
seizureduetohighlevelsofconsumptionduringoperation.
Always check oil regularly.
Figure 3. Grip Handle
2. The rammer should be greased with three shots of grease
after each eight (8) hours of use.
3. UseMQHIGHTEMPERATUREGREASE,P/NGRS2orits
equivalent.
Figure 5. Oil Tank
4. Equivalent greases include Shell Darina or Texaco
Thermatex, both of which have a bentone base and EP-2
rating.
CAUTION:
DO NOT USE REGULAR AUTOMOTIVE-
TYPE MOTOR OIL.
5. Ifaninferiorgreaseisused,itmaybecometoothickortoothin
due to changes in temperature, and improper lubrication
couldresult.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— INITIAL START-UP
2. Set the engine ON/OFF switch (Figure 7) to the "ON"
This section is intended to assist the
operator with the initial start-up of the
MTR-40HS rammer. It is extremely
important that this section be read
carefully before attempting to use the
rammer in the field.
position(start).
DO NOT use your rammer until this section is thoroughly
understood.
CAUTION:
Figure 7. ON/OFF Switch (ON Position)
Failure to understand the initial start-up
procedures of the MTR-40HS rammer could
result in severe damage to the rammer or
personal injury.
3. Move the throttle lever to the "IDLE" position (Figure 8).
See Figure 1 (Page 13) for the location of any control referenced
in this manual.
Initial Start-up
The following steps outline the procedure for starting the engine:
1. Open the fuel shut- off valve by moving the fuel cock
lever to the open position (Figure 6).
Figure 8. Throttle Lever (Idle)
4. Incoldweather,starttheunitwithchokelever"FullyClosed"
(Figure9). Inwarmweatherorwhentheengineiswarm,the
unitcanbestartedwithchokehalfwayorcompletelyopen.
Figure 6. Fuel Shut-Off Valve (Open)
Figure 9. Choke Lever (Closed)
PAGE 16 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— INITIAL START-UP
5
Griptherecoilstarter(Figure10)handleandpullituntilyou
feelaslightresistance. Thenpullsharplyandquickly. Return
therecoilstarterhandletothestarterpositionbeforereleas-
ing.
8. If the engine does not start after repeated attempts,
check thespark plug forexcess fuel. Clean and replace
the spark plug as needed.
9. If the carburetor is flooded or the crankcase is loaded with
excessfuel,openthedrainplugasshownin(Figure11)and
drain out excess fuel, then try and start engine.
Figure 10. Recoil Starter
6. Ifenginefailstostart,movethechokelever(Figure 9) tothe
half open position to avoid flooding.
Figure 11. Fuel Drain Cock
7. Repeat steps 1 through 6.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— OPERATION
Operation
1. To start the rammer tamping action, move the throttle lever
(Figure 12) quickly from IDLE (close) to the FULL OPEN
position. DONOTmovethethrottleleverslowlyasthismay
cause damage to the clutch or spring.
Figure 13.Throttle Lever (Idle)
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
“OFF” position (Figure 14).
Figure 12. Throttle Lever (Full Open)
CAUTION:
Make sure that the throttle lever is moved to the
FULL OPEN position. Operating the rammer at
less than full speeds can result in damage to the
clutch springs or foot
Figure 14. ON/OFF Switch (Off Position)
3. Closethefuelshut-offvalve(Figure15)bymovingthefuel
2. The MT-40HS tamping rammer is designed to run at 4,100
rpm. At optimum rpm the foot hits at the rate of 600~690
impacts per minute. Increasing throttlespeedpastfactory
setrpmdoesnotincreaseimpactsand maydamageunit.The
MT-40HS is designed toadvancewhiletamping.For faster
advance, pullbackslightlyonthehandlesothatrearof foot
contactssoilfirst.
cock lever to the CLOSED position.
Stopping The Engine
Normal Shutdown
1. Move throttle lever quickly from the FULL OPEN to IDLE
position (Figure13)andruntheengineforthreeminutesat
low speed.
Figure 15. Fuel Shut-Off Valve
(Closed Position)
Emergency Showdown
1. MovethethrottleleverquicklytotheIDLE position,andturn
theengineON/OFFswitchtotheOFFposition.Turnthefuel
valve lever to the CLOSED position.
PAGE 18 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— MAINTENANCE (RAMMER)
MAINTENANCE
BREATHER
ELEMENT
Perform the scheduled maintenance procedures as definded by
Table 3 (page 21) and below:
PAPER
ELEMENT
DAILY
GRAY OUTER
FOAM ELEMENT
■
Thoroughly remove dirt and oil from the engine compartment
and rammer. Clean or replace the air cleaner elements as
necessary.Check and retighten all fasteners as necessary.
Check the bellows for oil leaks. Repair or replace as needed.
200 - 300 HOURS (Pre-Cleaner)
CLEAN WITH
SOLVENT
CLEAN WITH
KEROSENE
■
Remove the element from the pre-cleaner (Figure 16) at the
top of the crankcase (body side) and clean it with cleaning oil
(kerosene).
Figure 17. Engine Air Cleaner
■
Tap the paper filter element (Figure 17) several times on a hard
surface to remove dirt, or blow compressed air [not exceeding
30 psi (207 kPa, 2.1 kgf/cm2)] through the filter element from the
air cleaner case side. NEVER brush off dirt. Brushing will force
dirt into the fibers. Replace the paper filter element if it is
excessively dirty.
CAUTION:
Itisnormalforanew2-strokeenginetoemitexcess
smoke, until moving parts have been seated to
theirnormaloperatingspecifications.Thisexcess
smoke normally stops after one full tank of fuel.
Figure 16. Primary Air Cleaner
SPARK PLUG
■
■
Lubricate the top element (yellow) with 2~5 cc of engine oil
SAE-30.
■
Remove and clean the spark plug (Figure 19), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
Lubricate bottom element (gray) with 7~9 cc of engine oil
SAE-30 and completely squeeze out the excess oil from the
element before installing.
■
The air cleaner (Figure 17) on the engine side will hardly be
contaminated, if it is, clean the outer foam gray element with
cleaning solvent. Tightly squeeze outer foam element to
remove any excess solvent before reinstalling.
Figure 19. Spark Plug Gap
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— MAINTENANCE (RAMMER)
2. Removetheboltsthatsecuretheoiltanktothefueltank,and
drain all oil from the tank.
CLEANINGTHE OILTANK
■
Clean the inside of the oil tank regularly, preferably 2 or 3 times
3. Removecockholder,thencleanstrainerandcockholderin
a kerosene solution.
ayear.
■
In winter, be sure to clean the inside of oil tank to avoid the
freezing of water that may have accumulated inside the tank.
4. Make sure every part is clean and dry, then reassemble oil
tank. Filloiltankwith2-strokeoutboardmotoroil(FBclass)
to the "H" level.
CAUTION:
FUEL AND OIL LINES
If water accidently got inside the oil tank, the oil
■
■
■
Check the fuel and oil lines regularly for damage and ensure
that there are no leaks.
may appear muddy.If this situation occurs, simply
flush the tank, removing all foreign matter
including water, and fill oil tank with fresh 2-
stroke outboard motor oil.
Replace fuel and oil lines every 2 years to maintain
performance.
■
When cleaning the oil tank (Figure 18) perform the following
procedure:
When replacing the oil hose perform the following procedure:
1. Replaceoilhosewithmanufacturessuggestedtypehoseor
equivalent.
1. Remove the cock holder cover, oil hose, red and black lead
wiresfromthefloatsensor.
2. Ifnecessary,filloiltankwith2-strokeoutboardmotoroiland
fuel tank wth unleaded gasoline.
3. Operate rammer until all air is bled from oil injection line.
CLEANINGTHERAMMER
■
If using a high pressure spray washer, be careful not to splash
water directly on the air cleaner, carburetor, muffler, fuel and
oil tank caps. Excessive amounts of water may cause severe
engine damage.
Yearly
■
Check the fuel line and the oil line regularly for damage and
to ensure that there are no leaks.
■
Replace the oil and fuel lines every two years to maintain the
performance and flexibility lines.
Long Term Storage
■
■
Drain fuel from fuel tank, fuel line and carburetor.
Remove spark plug and pour a few drops of motor oil into
cylinder. Crank engine 3 to 4 times so that oil reaches all
internal parts.
■
■
Clean exterior of rammer with an oil-moistened cloth.
Store unit covered with plastic sheet in moisture free and
dust free location out of direct sunlight
Reference manufacturer engine
Figure 18. Oil Tank
manual for specific servicing
instructions.
PAGE 20 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — MAINTENANCE (ENGINE)
Perform the scheduled engine maintenance procedures as
definded by Table 3 below:
Table 3. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
Valve Clearance
Fuel lines
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TROUBLESHOOTING GUIDE
TABLE 4. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available at
high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Check fuel to oil mixture.
Mixed fuel quality is inadequate?
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Clean or replace air cleaner.
Bleed (remove air) from fuel line.
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Adjust carbureator float
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Check fuel to oil mixture.
Mixed fuel quality is inadequate?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Clean or replace muffler.
Spark plug heat value incorrect?
Replace spark plug with correct type spark plug.
PAGE 22 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TROUBLESHOOTING GUIDE
TABLE 4. ENGINE TROUBLESHOOTING (continued)
POSSIBLE PROBLEM
SYMPTOM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Check suction line.
Air taken in through suction line?
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace spiral spring.
Recoil starter not working
properly.
TABLE 5. RAMMER TROUBLESHOOTING
POSSIBLE PROBLEM
SYMPTOM
SOLUTION
Operating speed of throttle lever Set throttle lever to correct position.
is incorrectly set?
Oil in excess?
Drain excess oil. Bring to correct level.
Replace or adjust clutch.
Engine rotates but amplituide
not uniform or does not strike.
Clutch slips?
Spring Failure?
Replace sprial spring.
Speed of engine improper?
Adjust engine speed to correct operating RPM setting.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
+
, %, or
*
>
, belong to the same assembly or kit.
If more than one of the same reference
number is listed, the last one listed
indicates newest (or latest) part
available.
PAGE 24 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— SUGGESTED SPARE PARTS
MTR-40HS RAMMER 1TO 3 UNITS
MTR-40HS RAMMER 4TO 10 UNITS
Qty.
P/N
Description
Qty.
P/N
Description
1 ......... 362910060 .......... THROTTLE LEVER ASSY.
1 ......... 956100044 .......... THROTTLE WIRE
1 ......... 0830000010 ........ SPRING, COIL
2 ......... 362910060 .......... THROTTLE LEVER ASSY.
2 ......... 956100044 .......... THROTTLE WIRE
2 ......... 0830000010 ........ SPRING, COIL
3 ......... 362030020 .......... ELEMENT, AIR CLEANER (YELLOW)
3 ......... 1573620101 ........ ELEMENT SET (ENGINE)
3 ......... 0650140031 ........ SPARK PLUG
6 ......... 362030020 .......... ELEMENT, AIR CLEANER (YELLOW)
6 ......... 1573620101 ........ ELEMENT SET (ENGINE)
6 ......... 0650140031 ........ SPARK PLUG
1 ......... 361910021 .......... CAP, FUEL TANK W/STRAP (ORANGE)
1 ......... 353030071 .......... CAP, OILTANK W/STRAP (YELLOW)
3 ......... 301419750 .......... FUEL FILTER, IN-LINE
1 ......... 954404890 .......... STRAINER, FUEL TANK (INSIDE)
1 ......... 954406010 .......... STRAINER, FUEL (BOTTOM)
1 ......... 5805011040 ........ STARTER ROPE
2 ......... 361910021 .......... CAP, FUEL TANK W/STRAP (ORANGE)
2 ......... 353030071 .......... CAP, OILTANK W/STRAP (YELLOW)
6 ......... 301419750 .......... FUEL FILTER, IN-LINE
2 ......... 954404890 .......... STRAINER, FUEL TANK (INSIDE)
2 ......... 954406010 .......... STRAINER, FUEL (BOTTOM)
2 ......... 5805011040 ........ STARTER ROPE
1 ......... 0660000361 ........ SWITCH, STOP
2 ......... 0660000361 ........ SWITCH, STOP
1 ......... 1293500403 ........ GASKET, COMPLETE EXHAUST
1 ......... 2263272008 ........ GASKET, AIR CLEANER
2 ......... 1063500103 ........ GASKET, INSULATOR, CARBURETOR
1 ......... KITCARBEC08H . CARBURETOR KIT
1 ......... 5806111000 ........ CARBURETOR ASSEMBLY
2 ......... 050100800 .......... O-RING, UPPER GUIDE CYLINDER
Part number on this Suggested
Spare Parts List may super cede/
replace the P/N shown in the text
pages of this book.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 26 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
NPA1017
DECAL: GASOLINE ONLY
DECAL:CAUTION (WATER)
DECAL:CAUTION (FUEL COCK)
DECAL: ENGINE RPM
2
920205990
920203990
920107660
920203980
NPA1016
920203290
920209630
920209910
920101200
NPA1018
920209100
920209610
920205810
920100240
920202930
1
3
1
4
1
5
DECAL: ELEMENT SET
DECAL: SECONDARY AIR FILTER
DECAL:CAUTION
DECAL: CLEANING ELEMENT
PLATE: SERIAL NO.
DECAL: GREASE
1
6
1
7
1
8
1
9
1
10
11
12
13
14
15
16
3
DECAL: PRIMARY AIR FILTER
DECAL: RAMMER BOOT & HEARING
DECAL: DECAL OIL 7-9 CC
DECAL: CAUTION/OIL INJECT
DECAL: (M-MARK)
1
1
1
1
1
DECAL: SWITCH-ON
1
FOR DECAL ILLUSTRATIONS SEE PAGE 10.
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— CRANKCASE AND ENGINE ASSY.
C
PAGE 28 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— CRANKCASE AND ENGINE ASSY.
CRANKCASE & ENGINE ASSY.
NO PART NO PART NAME
QTY.
CLUTCH GUIDE / A
RE1MARKS
1
305117260
CRANK CASE
1
45
0053204201 WOODRUFF KEY
301010210 LOCK WASHER CLUTCH
1
1
1
2
362341650
041006305
CRANK GEAR 1300-59Z
BEARING 6305Z
1
3
1
46
4
041006203
BEARING 6203Z
1
47
956300130 THROTTLE LEVER AY 25
5
952401450
001220825
030208200
305333090
042006304
080100520
952400130
001220825
030208200
362341610
002210620
351010050
303010084
042006007
080200350
351437750
351421900
060504010
050300900
002210830
301421365
943020020
943050050
943060010
943060020
943030020
301010210
0053204201
0173120010
362116870
WASHER 8.5 x 22 x 3
BOLT 8 x 25 T
1
1
1
1
1
1
1
1
1
1
9
2
1
2
1
1
1
1
1
4
6
7
WASHER, LOCK M8
CONNECTING ROD
BEARING 6304ZZ
STOP RING R-52
WASHER 9304
9
10
11
12
13
BOLT 8 x 25 T
14
WASHER, LOCK M8
PACKING, FRONT COVER
BOLT 6 x 20 H,SW
GREASE FITTING A-MT6X1
PINION
16
17
18
19
20
BEARING 6007ZZ
STOP RING S-35
SPACER 35.4-42.7-11
SPACES, CLUTCH DRUM
OIL SEAL VB-40525
O-RING S-90
21
22
23
24
25
27
BOLT 8 x 30 H,SW
28
CLUTCH ASSY. CE120E.................. 1............. INCLUDES ITEMS W/
*
28-1
28-2
28-3
28-4
28-5
CLUTCH SHOE
CLUTCH BOSS
4
1
1
1
2
1
1
1
*
*
*
*
*
CLUTCH GUIDE (A)
CLUTCH GUIDE (B)
CLUTCH SPRING
LOCKWASHER, CLUTCH
WOODRUFF KEY
LOCK NUT
29
*
30
31
32
AIR CLEANER ASSY. ...................... 1............. INCLUDES ITEMS W/#
32-1# 362030010
32-2# 362030020
32-3# 362030030
32-4# 362030040
32-5# 050300070
COVER CP, AIR CLEANER
PACKING, AIR CLEANER
ELEMENT CP, AIR CLEANER
BOLT CP, AIR CLEANER
O-RING (7)
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
34
35
36
58
59
60
68#
70
75
80
81
82
88
031108160
362341210
507010110
362455660
002210620
050100350
031108160
362010060
911100843
353448490
2267510103
355450600
64016
WASHER, FLAT M8
INTAKE PIPE
CLAMPTC-200
BEARING COVER
BOLT 6X20 H,SW
O-RING G-35
WASHER, FLAT M8
FRONT COVER
ENGINE ASSY. EC08DXX(EPA)
WIRE CP
CLAMP
OUTER LINER 525L
HOSE CLAMP 13x16, 1-1/2" SS
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS — GUIDE CYLINDER ASSY.
GUIDE CYLINDER AND FOOT ASSY.
PAGE 30 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— GUIDE CYLINDER ASSY.
GUIDE CYLINDER & FOOT ASSY.
NO
1
PART NO
PART NAME
QTY.
1
REMARKS
305446380
080100120
305337980
305451550
305446400
305446410
305446420
305212710
305112730
065105010
080510680
351010050
305446430
002210815
305446440
001520815
305446450
305446460
001200830
020308060
050100800
002211025
PISTON PIN
2
STOP RING R-12
PISTON ROD,M14
PISTON END,M14
STOPPER, UPPER
CYLINDER CAP
MAIN SPRING
2
3
1
4
1
6
1
7
1
8
2
9
SPRING CYLINDER
GUIDE CYLINDER
DUST SEAL DKI-5367811
STOP RINGTH-R-68
GREASE FITTING A-MT6x1
STOPPER
1
11
12
13
14
15
16
18
19
20
21
22
23
25
26
1
1
1
2
1
BOLT 8x15 H, SW
GRIP
4
1
SOCKET HEAD BOLT 8x15 T
DUST SLEEVE
SLEEVE BAND
BOLT 8x30
2
1
1
1
NUT M8
1
O-RING G-80
1
BOLT 10x25 H, SW
4
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TANK AND HANDLE ASSY.
PAGE 32 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TANK AND HANDLE ASSY.
TANK & HANDLE ASSY.
NO
3
PART NO
PART NAME
QTY.
4
REMARKS
009110007
002211020
351437785
954406020
954406010
001220830
022710809
952401450
030208200
954406000
939010210
030208200
020308060
305117330
351319900
361116910
361910070
001200610
030206150
2267510103
362910060
362341550
362455620
302443340
954403030
301419750
301420330
362455610
954404890
362455630
050100450
050200100
031110160
033910070
096206006
022131008
020410060
096208020
020408050
353213710
353449001
BOLT, W/STAR WASHER 10x20
BOLT 10x20 H, SW
HOLDER, COCK
PACKING, FUEL TANK
STRAINER (#110)
BOLT 8x30 T
4
4
9
1
10
11
12
13
14
15
16
18
19
20
24
25
26
27
29
30
31
32
33
1
1
2
NYLON NUT M8
WASHER 8.5x22x3
SW M8
FUEL COCK ASSY. N18L-02
STOPPER RUBBER EH1002
SW M8
NUT M8
HANDLE
2
2
2
1
1
1
1
1
SHOCK ABSORBER
FUEL TANK 2.5L (GRAY)
TANK CAP CP (ORANGE)
BOLT 6x10
WASHER, LOCK M6
CLAMP
2
1
1
1
1
1
THROTTLE LEVER ASSY. .......................... 1 ............ INCLUDES ITEMS W/
*
THROTTLE BODY
SLIDER
FUEL HOSE R-75
HOSE BAND (8)
FUEL FILTER CP
FUEL HOSE R-170
THROTTLE GEAR
FILTER, TANK
1
1
1
4
1
1
1
1
1
1
1
3
2
1
1
1
1
2
1
1
*
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
*
*
THROTTLE LEVER
O-RING G-45
O-RING P-10
*
*
*
*
*
*
WASHER, FLAT M10
CONICAL SPRINGWASHER
SOCKET HEAD SCREW 6 x 6
CAP NUT M10
NUT M10, H=6
SOCKET HEAD SCREW 8 x 20
NUT M8, H=5
*
OIL TANK
STRAINER, OIL TANK
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TANK AND HANDLE ASSY.
PAGE 34 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TANK AND HANDLE ASSY.
TANK & HANDLE ASSY.
NO
53
54
55
56
57
58
59
60
61
62
63
65
66
67
70
71
72
PART NO
PART NAME
QTY.
REMARKS
353030071
956100044
353910020
959401750
091004010
001220620
030206150
022130605
353450220
355448071
0830000010
353030080
091005015
952405970
009110011
030208200
952401450
OIL TANK CAP CP (YELLOW)
THROTTLE WIRE S390-485
OIL SENSOR ASSY.
1
1
1
WIRE STOPPER ASSY. (2.5D) .......... 1 .............. 340210100
SCREW 4 x 10.................................... 1 .............. 301010820
BOLT 6 x 20T
2
2
2
1
1
1
1
1
1
2
2
2
SW M6
CAP NUT M6
GUARD, OIL HOSE
COVER, COCK HOLDER
COIL SPRING
WELL NUT M5
SCREW 5x15
WASHER 6.4D-20D
SOCKET HEAD SCREW 8x20
SW M8
WASHER 8.5x22x3
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— FOOT ASSY. (OPTION)
FOOT ASSY. (OPTION)
PAGE 36 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— FOOT ASSY. (OPTION)
FOOT ASSY. (OPTION)
NO
30
PART NO
PART NAME
QTY.
REMARKS
305910010
305333120
305333130
305446470
001611050
022711012
030210250
001611252
022711214
030212300
FOOT ASSY. 150B ....................... 1 .......... INCLUDES ITEMS W/
*
31
FOOT 150B
1
1
1
2
2
2
4
4
4
*
32
33
34
35
36
37
38
39
METAL SHEET 150B
FOOT COVER
*
*
*
*
*
*
*
*
SUNK HEAD BOLT 10x50 H
NYLON NUT M10
WASHER, LOCK M10
SUNK HEAD BOLT 12x60 H
NYLON NUT M12
WASHER, LOCK M12
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— NARROW FOOT ASSY. (OPTION)
NARROW FOOT ASSY. (OPTION)
PAGE 38 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS— NARROW FOOT ASSY. (OPTION)
NARROW FOOT ASSY. (OPTION)
NO
A
PART NO
PART NAME
QTY.
REMARKS
305910020
305910040
305333140
305334930
305333150
305334940
305446470
305447810
001611050
022711012
030210250
001611252
022711214
030212300
FOOT ASSY. 200B........................................ 1 ........... INCLUDESITEMS W/
*
A
FOOT ASSY. 100B........................................ 1 ........... INCLUDES ITEMS W/#
FOOT 200B ................................................... 1 ........... 200B
FOOT 100B ................................................... 1 ........... 100B
METAL SHEET 200B .................................... 1 ........... 200B
METAL SHEET 100B .................................... 1 ........... 100B
FOOT COVER ............................................... 1 ........... 200B
FOOT COVER 96B ....................................... 1 ........... 100B
1
*
1#
2
*
2#
3
*
3#
4 #
SUNK HEAD BOLT 10x50 H
NYLON NUT M10
2
2
2
4
4
4
*
5 #
*
6 #
*
WASHER, LOCKM10
SUNK HEAD BOLT 12x60 H
NYLON NUT M12
7 #
*
8 #
*
9 #
*
WASHER, LOCK M10
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TRENCH SHOE ASSY. (OPTION)
TRENCH SHOE ASSY.
PAGE 40 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MTR-40HS—TRENCH SHOE ASSY. (OPTION)
TRENCH SHOE ASSY.
NO
11
11
11
12
13
14
PART NO
PART NAME
QTY.
REMARKS
305333160
305333170
305334390
001221235
020312100
030212300
TRENCH SHOE 500H-120B
TRENCH SHOE 800H-120B
TRENCH SHOE 305H-100B
BOLT 12x35 T
1
1
1
4
4
4
NUT M12
WASHER, LOCK M12
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CRANKCASE AND CYLINDER ASSY.
CRANKCASE AND CYLINDER ASSY.
PAGE 42 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CRANKCASE AND CYLINDER ASSY.
CRANKCASE AND CYLINDER ASSY.
NO
10
PART NO
PART NAME
QTY.
REMARKS
5801056000
0440200020
0440200020
0440060010
0600200010
0600200020
0052606140
0011406450
0105060050
0105064940
0643000101
5809501600
0011308180
5801501800
0021706000
030206150
0031006000
5801501400
1507520103
CRANK CASE CP ................................1 ............INCLUDES ITEMS W/
*
30
OIL SEAL
1
1
1
1
1
2
4
1
4
*
35
36
40
41
50
95
OIL SEAL
*
*
*
*
*
OIL SEAL
BALL BEARING 6004C3
BALL BEARING 6204C3
DOWEL PIN
BOLT ASSY
STUD
105
115
140
145
146
170
180
190
200
510
850
*
STUD
*
DRAIN COCK ....................................... 1 ............REPLACES 0643109980
PROTECTOR COMP. ..........................1 ............REPLACES 5809011000
BOLT AND WASHER ASSY
GASKET, CYLINDER
3
1
NUT ...................................................... 4 ............REPLACES 0021806000
SPRING WASHER ............................... 4 ............REPLACES 0032006000
WASHER
CYLINDER CP
4
1
CLAMP ................................................. 1 ............REPLACES 0566099950
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CRANKSHAFT AND PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
PAGE 44 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CRANKSHAFT AND PISTON ASSY.
CRANKSHAFT AND PISTON ASSY.
NO
10
PART NO
PART NAME
CRANK SHAFT
WOODRUFF KEY
SPACER
NUT ...................................................... 1 ............REPLACES 0021810000
SPRING WASHER ............................... 1 ............REPLACES 0032010000
WASHER .............................................. 1 ............REPLACES 0031010000
WOODRUFF KEY
PLATE, GOVERNOR
SCREW (PAN HEAD) .......................... 3 ............REPLACES 0043105080
QTY.
REMARKS
5802028000
0323049950
1292500103
0039310000
030210250
030206150
0053204201
5804010000
0131050020
0032005000
5514500100
0230230020
0173120010
5802500700
5802500600
5802023000
0565119990
0610120010
1
1
2
30
40
50
60
65
70
1
1
REPLACES 0323049950
130
131
132
140
160
170
350
360
370
380
390
SPRING WASHER
GOVERNOR SLEEVE
SPACER
3
1
1
1
LOCK NUT
PISTON PIN ......................................... 1 ............REPLACES 5802500400
PISTON
1
PISTON RING SET .............................. 1 ............REPLACES 5000008100
CLIP
NEEDLE BEARING
2
1
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — GOVERNOR ASSY.
PAGE 46 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — GOVERNOR ASSY.
GOVERNOR ASSY.
NO
10
PART NO
PART NAME
GOVERNOR LEVER
BUSH
QTY.
REMARKS
5804005000
5804500900
2266255008
1294220103
1054270111
1064280113
1294250111
1294210113
0140039980
57028
1
2
15
16
BUSH, NYLON ..................................... 1 ............REPLACES 5806083060
20
GOVERNOR SHAFT
GOVERNOR ROD
ROD SPRING ......................................1 ............REPLACES 1064280111
GOVERNOR SPRING
GOVERNOR YOKE
SCREW ASSY
NUT ...................................................... 1 ............REPLACES 0021706000
SPRING WASHER ............................... 1 ............REPLACES 0032006000
1
1
30
40
80
1
1
2
90
100
120
130
305
310
340
341
342
350
360
370
380
400
480
610
620
030206150
0217060020
5804500800
5804500600
0230060090
0105050616
0200070010
0016506400
57028
0170069960
1294500103
402010110
0149060040
020106050
FRICTION WASHER
CONTROL LEVER
STOP PLATE
1
1
1
1
SPACER
BOLT .................................................... 1 ............REPLACES 6202500400
WASHER
BOLT
1
1
NUT ...................................................... 1 ............REPLACES 0021706000
U NUT
CLIP
1
1
COIL SPRING ......................................1 ............REPLACES 0830000010
ADJUSTING SCREW ..........................1 ............REPLACES 0149069981
NUT ...................................................... 1 ............REPLACES 0022706000
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 48 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO
300
308
309
310
330
331
340
350
355
356
361
362
PART NO
PART NAME
QTY.
REMARKS
0016706200
0031206000
0566099950
5803032000
5803033000
5803034000
1293500403
0170069960
030206150
0031006000
0016706160
0031006000
MUFFLER
2
2
1
1
1
1
1
2
WASHER, FLAT
CLAMP
MUFFLER
MUFFLER BRACKET A
MUFFLER BRACKET B
GASKET (MUFFLER)
U-NUT
SPRING WASHER ............................... 7 ............REPLACES 0032006000
WASHER
BOLT (MUFFLER)
WASHER
4
4
2
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CARBURETOR AND OIL PUMP ASSY.
CARBURETOR AND OIL PUMP ASSY.
PAGE 50 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CARBURETOR AND OIL PUMP ASSY.
CARBURETOR AND OIL PUMP ASSY.
NO
210
250
700
705
706
710
716
720
730
731
732
733
740
745
750
760
765
PART NO
PART NAME
QTY.
REMARKS
5806111000
1616235308
5806113000
5806502300
0323039980
0011306250
0031520000
1616350101
5806501900
0119089970
030208200
0031008000
5806502000
5806502100
5806502200
0566059980
0119059610
CARBURETOR ASSY ......................... 1 ............SEE CARBURETOR FIG. FOR COMPONENTS
HOSE
1
1
1
1
2
2
1
1
4
OIL PUMP ASSY
WORM GEAR
WOODRUFF KEY
BOLT AND WASHER ASSY
SNAP RING, OUTER
COLLAR CP (OIL INJ.)
OIL PUMP HOUSING
SOCKET HEAD BOLT
SPRING WASHER ............................... 4 ............REPLACES 0032008000
WASHER
4
1
1
1
1
1
GROMMET
SEAL
PLATE
CLAMP
SOCKET HEAD BOLT
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — RECOIL STARTER AND BLOWER ASSY.
RECOIL STARTER AND BLOWER ASSY.
PAGE 52 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — RECOIL STARTER AND BLOWER ASSY.
RECOIL STARTER AND BLOWER ASSY.
NO
10
15
20
25
26
40
50
51
52
53
210
PART NO
PART NAME
QTY.
REMARKS
5805501200
5515500200
920100240
5809503800
5809500501
0011106200
5805022000
011206020
0031206000
030206150
5805001000
FAN COVER
1
1
1
1
GUIDE RUBBER
DECAL, (M-MARK)
LABEL, ENGINE
LABEL, MODEL
BOLT ASSY
4
1
CYLINDER COVER CP
BOLT (CYLINDER) .............................. 2 ............REPLACES 0016706200
WASHER
2
SPRING WASHER ............................... 2 ............REPLACES 0032006000
RECOIL STARTER ASSY....................1 ............SEE RECOIL STARTER FIG. FOR COMPONENTS’
REPLACES 5805011001
220
230
850
0011006100
0011006140
0566000250
BOLT AND WASHER ASSY
BOLT ASSY
CLAMP
3
2
2
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 54 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO
510
520
521
522
540
550
560
580
600
PART NO
PART NAME
QTY.
REMARKS
5803052000
1573620101
1613261008
2263272008
1293290103
1063500103
2373590303
0011306800
030206150
AIR CLEANER ASSY ........................... 1 ............INCLUDES ITEMS W/
*
ELEMENT SET .................................... 1 ............REPLACES 1573260007
*
*
*
ELEMENT
1
1
1
2
1
2
GASKET (AIR CLEANER)
INSULATOR
GASKET (INSULATOR)
GASKET 2 (INSULATOR)
BOLT
SPRING WASHER ............................... 2 ............REPLACES 0032006000
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CARBURETOR COMPONENTS ASSY.
CARBURETOR COMPONENTS ASSY.
PAGE 56 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — CARBURETOR COMPONENTS ASSY.
CARBURETOR COMPONENTS ASSY.
NO
A
PART NO
PART NAME
QTY.
REMARKS
5806117000
1616253508
5806111010
5806083310
5806111010
2076242008
2136239008
2096244508
5806083040
5806083050
5806083030
5806083020
5806083360
1616235208
2146251508
1616235008
2366245008
2366254008
5806083350
5806083260
1296240008
5806083150
2366235008
2096244508
5806083230
5806083210
5806083230
2366244508
2366254108
5806083140
5806083120
5806083370
KITCARBEC08H
CARBURETOR ASSY. (EPA) ................. 1 ................ INCLUDES ITEMS W/
*
1
THROTTLE VALVE ................................ 1 ................ REPLACES 5806083110
*
2
SCREW AND WASHER ASSY.
CHOKE VALVE
2
1
2
*
3
*
4
SCREW AND WASHER ASSY.
*
5 #
PILOT JET .............................................. 1 ................ REPLACES 5606003020
PILOT SCREW ....................................... 1 ................ REPLACES 5416002150
SPRING .................................................. 1 ................ REPLACES 8046001230
*
6 #
*
7 #
*
8
9
CHOKE LEVER
1
1
1
1
1
1
*
RING
*
11
THROTTLE SHAFT ASSY.
*
12 #
BOLT
*
13
RING
*
14 #
NEEDLE
REPLACES 5806083400
*
15 #
PIN .......................................................... 1 ................ REPLACES 5416002050
FLOAT BODY ASSY. .............................. 1 ................ REPLACES 5806083010
PACKING ................................................ 1 ................ REPLACES 5806083330
PACKING ................................................ 1 ................ REPLACES 5806083340
*
16
*
17 #
*
18 #
*
19 #
FLOAT
1
1
1
1
1
*
20
MAIN NOZZLE
MAIN JET
SCREW
*
22 #
REPLACES 5306011010
REPLACES 5416002230
*
28
*
40 #
SCREW
*
41 #
SPRING .................................................. 1 ................ REPLACES 8046001230
PACKING ................................................ 1 ................ REPLACES 5806083230
*
60
*
62
SEAL
1
*
63
SCREW .................................................. 1 ................ REPLACES 5806083230
SPRING .................................................. 1 ................ REPLACES 5806083240
PACKING ................................................ 1 ................ REPLACES 5806083320
*
82 #
*
104
*
106
SPRING
1
1
1
*
107
RING
*
108
FLOAT STOPPER
*
#
KIT, CARBURETOR EC08HS................ 1 ................ INCLUDES ITEMS W/#
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — RECOIL STARTER COMPONENTS ASSY.
RECOIL STARTER COMPONENTS ASSY.
PAGE 58 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — RECOIL STARTER COMPONENTS ASSY.
RECOIL STARTER COMPONENTS ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
1
5515005160
5805001030
5805011040
5805004020
5805004030
5805004050
5805004040
5805004110
5805004120
5805011020
5805004140
5805001000
ROPE STOPPER
STARTER HANDLE
STARTER ROPE
SPIRAL SPRING
REEL
1
1
1
1
1
1
1
1
*
2
*
3
*
4
*
5
*
6
RETURN SPRING
RATCHET
FRICTION SPRING
*
7
*
8
*
9
FRICTION PLATE ................................1 ............REPLACES EC08A05038
*
10
11
12
CENTER SCREW
1
*
STARTER PULLEY .............................. 1 ............REPLACES EC08A050311
*
RECOIL STARTER ASSY. ................... 1 ............INCLUDES ITEMS W/
*
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — MAGNETO ASSY.
MAGNETO ASSY.
PAGE 60 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — MAGNETO ASSY.
MAGNETO ASSY.
NO.
10
PART NO.
PART NAME
QTY.
REMARKS
5807005010
5807007020
0851029960
0011105250
1507520103
0660000361
0043304100
0241069980
0659000010
0650140031
0655000140
FLYWHEEL
1
1
1
2
11
IGNITION COIL
VINYL PIPE
18
30
BOLT AND WASHER ASSY
40
CLAMP ................................................. 1 ............REPLACES 0566099950
60
STOP SWITCH ASSY (ON-OFF)
SCREW 4X10
1
2
1
70
81
GROMMET
95
SPARK PLUG CLIP .............................. 1 ............REPLACES 0655000100
SPARK PLUG ....................................... 1 ............REPLACES 00650149730
100
110
SPARK PLUG CAP
1
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — OIL PUMP ASSY.
PAGE 62 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ROBIN EC-08HS ENGINE — OIL PUMP ASSY.
OIL PUMP ASSY.
NO.
1
PART NO.
PART NAME
OIL PUMP ASSY.
OIL HOSE
QTY.
REMARKS
5806113000
5806113020
5806113030
5806113040
1616391608
1616391008
2266235408
1616391909
5806113140
1
1
1
1
3
2
3
OIL HOSE
4
PROTECTOR
CLIP
6
7
CLIP ...................................................... 1 ............REPLACES 0566099950
11
12
13
SCREW
1
1
PACKING
PROTECTOR
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon-
dition,intheoriginalMultiquippackage(if
any), and with Multiquip part numbers
clearlymarked.
Multiquipreservestherighttoquoteandsell
directtoGovernmentagencies,andtoOrigi-
nal Equipment Manufacturer accounts who
useourproductsasintegralpartsoftheirown
products.
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signedmanifesthasbeenobtainedfromthe
carrier,andanyclaimforshortageordamage
mustbesettledbetweentheconsigneeandthe
carrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
A$35.00surchargewillbeaddedtotheinvoice
forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchasedmorethansixmonthsprior
tothereturndate.
LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
forinstructionsregardinghandlingoforders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
turedbyMultiquip.Suchwarrantiesmadein
connectionwiththesaleofnew,completeunits
aremadeexclusivelybyastatementofwar-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. The sender will be notified of any
materialreceivedthatisnotacceptable.
2. To obtain a Return Material Authoriza-
tion,alistmustbeprovidedtoMultiquip
Parts Sales that defines item numbers,
quantities,anddescriptionsoftheitems
tobereturned.
8. Such material will be held for five
workingdaysfromnotification,pending
instructions. If a reply is not received
within five days, the material will be re-
turnedtothesenderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s) or invoice(s) under which
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
forpricedeclinesandaddedchargesforprice
increaseswillnotbemadeforstockonhand
atthetimeofanypricechange.
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PAGE 64 — MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MTR-40HS— PARTS & OPERATION MANUAL — REV. #2 (12/15/03) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
manufactured for Multiquip Inc.
by
MIKASA SANGYO CO., LTD. Tokyo, Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|