Multiquip Music Mixer WM63H5 User Manual
OperatiOn and parts Manual  
series  
MOdels  
WM63H5, WM63H8  
WM63e  
plaster and MOrtar Mixer  
(HOnda Gx160ut1Hx2/Gx240ut1Ha2  
GasOline enGines)  
Revision #0 (09/27/12)  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
silicOsis/respiratOry WarninGs  
WARNING WARNING  
SILICOSIS WARNING  
RESPIRATORY HAZARDS  
Grinding/cutting/drilling of masonry, concrete, metal and  
other materials with silica in their composition may give  
off dust or mists containing crystalline silica. Silica is a  
basic component of sand, quartz, brick clay, granite and  
numerous other minerals and rocks. Repeated and/or  
substantial inhalation of airborne crystalline silica can  
cause serious or fatal respiratory diseases, including  
silicosis. In addition, California and some other  
authorities have listed respirable crystalline silica as a  
substance known to cause cancer. When cutting such  
materials, always follow the respiratory precautions  
mentioned above.  
Grinding/cutting/drilling of masonry, concrete, metal and  
other materials can generate dust, mists and fumes  
containing chemicals known to cause serious or fatal  
injury or illness, such as respiratory disease, cancer,  
birth defects or other reproductive harm. If you are  
unfamiliar with the risks associated with the particular  
process and/or material being cut or the composition of  
the tool being used, review the material safety data  
sheet and/or consult your employer, the material  
manufacturer/supplier, governmental agencies such as  
OSHA and NIOSH and other sources on hazardous  
materials. California and some other authorities, for  
instance, have published lists of substances known to  
cause cancer, reproductive toxicity, or other harmful  
effects.  
Control dust, mist and fumes at the source where  
possible. In this regard use good work practices and  
follow the recommendations of the manufacturers or  
suppliers, OSHA/NIOSH, and occupational and trade  
associations. Water should be used for dust  
suppression when wet cutting is feasible. When the  
hazards from inhalation of dust, mists and fumes cannot  
be eliminated, the operator and any bystanders should  
always wear a respirator approved by NIOSH/MSHA for  
the materials being used.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
table Of cOntents  
component drawings  
WM63H5/WM63H8/WM63e  
Nameplate And Decals..................................... 40-41  
Frame Assembly............................................... 42-43  
Paddle Shaft Assembly..................................... 44-45  
Steel Tub Assembly .......................................... 46-47  
Drum And Paddle Shaft Complete Assembly... 48-49  
Axle Assembly.................................................. 50-51  
Engine Assembly.............................................. 52-53  
Electric Motor Assembly................................... 54-55  
Cabinet Assembly............................................. 56-57  
plaster and Mortar Mixers  
Proposition 65 Warning ........................................... 2  
Silicosis/Respiratory Warnings................................ 3  
Table Of Contents.................................................... 4  
Parts Ordering Procedures...................................... 5  
Safety Information .............................................. 6-10  
Safety Chain Connection....................................... 11  
Specifications ........................................................ 12  
Dimensions............................................................ 13  
General Information............................................... 14  
Components .......................................................... 15  
Inspection ......................................................... 16-17  
Basic Engine.......................................................... 18  
Electric Motor ................................................... 19-20  
Paddle Blade Adjustment ...................................... 21  
Start-Up............................................................ 22-23  
Operation............................................................... 24  
Maintenance (Engine) ...................................... 26-27  
Maintenance (Mixer)......................................... 28-33  
Troubleshooting ................................................ 34-36  
Wiring Diagram...................................................... 37  
Explanation Of Code In Remarks Column............. 38  
Suggested Spare Parts ......................................... 39  
Terms And Conditions Of Sale — Parts ................ 56  
NOTICE  
Specifications and part numbers are subject to change  
without notice.  
page 4 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
parts OrderinG prOcedures  
Ordering parts has never been easier!  
choose from three easy options:  
Effective:  
January 1st, 2006  
Best deal!  
order via internet (dealers only):  
Order parts on-line using Multiquip’s SmartEquip website!  
If you have an MQ Account, to obtain a Username  
and Password, E-mail us at: parts@multiquip.  
com.  
I View Parts Diagrams  
I Order Parts  
I Print Specification Information  
To obtain an MQ Account, contact your  
District Sales Manager for more information.  
Use the internet and qualify for a 5% discount  
on Standard orders for all orders which include  
complete part numbers.*  
Goto www.multiquip.com and click on  
to log in and save!  
Order Parts  
Note: Discounts Are Subject To Change  
Fax your order in and qualify for a 2% discount  
on Standard orders for all orders which include  
complete part numbers.*  
order via Fax (dealers only):  
All customers are welcome to order parts via Fax.  
domestic (us) Customers dial:  
1-800-6-PARTS-7 (800-672-7877)  
Note: Discounts Are Subject To Change  
domestic (us) dealers Call:  
order via phone:  
1-800-427-1244  
non-dealer Customers:  
International Customers should contact  
their local Multiquip Representatives for  
Parts Ordering information.  
Contact your local Multiquip Dealer for  
parts or call 800-427-1244 for help in  
locating a dealer near you.  
When ordering parts, please supply:  
Ì
dealer account number  
Ì
specify preferred method of shipment:  
Ì
Ì
Ì
Ì
Ì
dealer name and address  
ꢀ UPS/Fed Ex  
ꢀ DHL  
ꢀ Truck  
I
I
Priority One  
Ground  
shipping address (if different than billing address)  
return Fax number  
I Next Day  
Second/Third Day  
applicable model number  
I
Quantity, part number and description of each part  
NOTICE  
All orders are treated as Standard Orders and will  
ship the same day if received prior to 3PM PST.  
we aCCepT all maJor CrediT Cards!  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety infOrMatiOn  
Do not operate or service the equipment before reading  
the entire manual. Safety precautions should be followed  
at all times when operating this equipment.  
Failure to read and understand the safety  
messages and operating instructions could  
result in injury to yourself and others.  
Potential hazards associated with the operation of this  
equipment will be referenced with hazard symbols which  
may appear throughout this manual in conjunction with  
safety messages.  
Symbol  
Safety Hazard  
saFeTY messages  
Lethal exhaust gas hazards  
The four safety messages shown below will inform you  
about potential hazards that could injure you or others.The  
safety messages specifically address the level of exposure  
to the operator and are preceded by one of four words:  
danger, warning, CauTion or noTiCe.  
Explosive fuel hazards  
Burn hazards  
saFeTY sYmBols  
danger  
Indicates a hazardous situation which, if not avoided,  
will result in deaTH or serious inJurY.  
warning  
Indicates a hazardous situation which, if not avoided,  
Could result in deaTH or serious inJurY.  
Rotating parts hazards  
CauTion  
Indicates a hazardous situation which, if not avoided,  
Could result in minor or moderaTe inJurY.  
NOTICE  
Addresses practices not related to personal injury.  
page 6 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety infOrMatiOn  
general saFeTY  
NOTICE  
CauTion  
„ This equipment should only be operated by trained and  
qualified personnel 18 years of age and older.  
„ never operate this equipment without proper protective  
clothing, shatterproof glasses, respiratory protection,  
hearing protection, steel-toed boots and other protective  
devices required by the job or city and state regulations.  
„ Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
„ Manufacturer does not assume responsibility for any  
accident due to equipment modifications. Unauthorized  
equipment modification will void all warranties.  
„ never use accessories or attachments that are not  
recommended by Multiquip for this equipment. Damage  
to the equipment and/or injury to user may result.  
„ Avoid wearing jewelry or loose fitting clothes that may  
snag on the controls or moving parts as this can cause  
serious injury.  
„ alwaYs know the location of the nearest  
fire extinguisher.  
„ never operate this equipment when not  
feeling well due to fatigue, illness or when  
under medication.  
„ alwaYs know the location of the nearest  
first aid kit.  
„ never operate this equipment under the  
influence of drugs or alcohol.  
„ alwaYs know the location of the nearest phone or keep  
a phone on the job site. Also, know the phone numbers  
of the nearest ambulance, doctor and fire department.  
This information will be invaluable in the case of an  
emergency.  
„ alwaYs clear the work area of any debris, tools, etc.  
that would constitute a hazard while the equipment is  
in operation.  
„ alwaYs check the equipment for loosened threads or  
bolts before starting.  
„ do noT use the equipment for any purpose other than  
its intended purposes or applications.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety infOrMatiOn  
engine saFeTY (gasoline models onlY)  
mixer saFeTY  
danger  
danger  
„ Engine fuel exhaust gases contain poisonous carbon  
monoxide. This gas is colorless and odorless, and can  
cause death if inhaled.  
„ neveroperatetheequipmentinanexplosive  
atmosphereornearcombustiblematerials.An  
explosion or fire could result causing severe  
bodily harm or even death.  
„ The engine of this equipment requires an adequate  
free flow of cooling air. never operate this equipment  
in any enclosed or narrow  
„ do noT mix flammable or explosive substances.  
warning  
area where free flow of the  
air is restricted. If the air  
„ never place your hands inside the drum  
while starting or operating this equipment.  
flow is restricted it will cause  
injury to people and property  
and serious damage to the  
„ never disconnect any emergency  
or safety devices. These devices are  
intended for operator safety. Disconnection of these  
devices can cause severe injury, bodily harm or even  
death. Disconnection of any of these devices will void  
all warranties.  
DANGEROUS  
GAS FUMES  
equipment or engine.  
warning  
„ do noT place hands or fingers inside engine  
compartment when engine is running.  
„ Before operating mixer, ensure that safety grate is in  
position and correctly fitted.  
„ never operate the engine with heat shields or  
guards removed.  
CauTion  
„ Keep fingers, hands hair and clothing away  
from all moving parts to prevent injury.  
„ never lubricate components or attempt service on a  
running machine.  
„ do noT remove the engine oil drain plug  
while the engine is hot. Hot oil will gush out of the oil  
tank and severely scald any persons in the general area  
of the mixer.  
NOTICE  
„ alwaYs keep the machine in proper running condition.  
„ alwaYs ensure mixer is on level ground before mixing.  
CauTion  
„ Fix damage to machine and replace any broken parts  
immediately.  
„ never touch the hot exhaust manifold,  
muffler or cylinder.Allow these parts to cool  
before servicing equipment.  
„ do noT tip mixer onto drum mouth when the drum is  
rotating.  
„ Make certain the operator knows how to and is capable  
of turning the engine OFF in case of an emergency.  
„ Ensure the drum is rotating while filling and emptying  
the drum.  
NOTICE  
„ alwaYs store equipment properly when it is not being  
used.Equipment should be stored in a clean, dry location  
out of the reach of children and unauthorized personnel.  
„ never run engine without an air filter or with a dirty air  
filter.Severe engine damage may occur.Service air filter  
frequently to prevent engine malfunction.  
„ never tamper with the factory settings  
of the engine or engine governor. Damage  
to the engine or equipment can result  
if operating in speed ranges above the  
maximum allowable.  
page 8 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety infOrMatiOn  
Fuel saFeTY (gasoline models onlY)  
power Cord/Cable safety  
danger  
danger  
„ do noT start the engine near spilled fuel or combustible  
fluids. Fuel is extremely flammable and its vapors can  
cause an explosion if ignited.  
„ never let power cords or cables lay in water.  
„ never use damaged or worn cables or cords when  
connecting equipment to generator. Inspect for cuts in  
the insulation.  
„ alwaYs refuel in a well-ventilated area, away from  
sparks and open flames.  
„ never grab or touch a live power  
cord or cable with wet hands. The  
possibility exists of electrical shock,  
electrocution or death.  
„ alwaYs use extreme caution when working with  
flammable liquids.  
„ do noT fill the fuel tank while the engine is running  
or hot.  
„ Make sure power cables are securely connected.  
Incorrect connections may cause electrical shock and  
damage to the mixer.  
„ do noT overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or sparks from  
the ignition system.  
CauTion  
„ Store fuel in appropriate containers, in well-ventilated  
areas and away from sparks and flames.  
„ Ensure that cables and cords will not be tripped over or  
trapped underneath the mixer.  
„ never use fuel as a cleaning agent.  
NOTICE  
„ do noT smoke around or near the  
equipment. Fire or explosion could result  
from fuel vapors or if fuel is spilled on a  
hot engine.  
„ alwaYs make certain that proper power or extension  
cord has been selected for the job.  
TransporTing saFeTY  
CauTion  
generaTor saFeTY  
„ never allow any person or animal to stand underneath  
the equipment while lifting.  
If using a generator to power mixer, refer to  
applicablegeneratormanualsafetyinformation  
section.  
NOTICE  
eleCTriC moTor saFeTY  
(eleCTriC models onlY)  
„ alwaYsmake sure forklift forks are inserted into pockets  
(if applicable) as far as possible when lifting the mixer.  
„ alwaYs shutdown engine before transporting.  
NOTICE  
„ never lift the equipment while the engine is running.  
„ Operate electric motor only at the specified voltage  
indicated on the nameplate.  
„ Tighten fuel tank cap securely and close fuel cock to  
prevent fuel from spilling.  
„ do noT spray water onto electric motor.  
„ do noT lift machine to unnecessary heights.  
„ alwaYs disconnect AC power plug from power source  
before moving mixer.  
„ alwaYs tie down equipment during transport by  
securing the equipment with rope.  
„ alwaYs make sure the ON/OFF switch  
on the electric motor is in the OFF position  
when not in use and before inserting the  
mixer’s power plug into an AC receptacle.  
„ never tip the engine to extreme angles during lifting as  
it may cause oil to gravitate into the cylinder head, making  
the engine start difficult.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety infOrMatiOn  
Towing saFeTY  
environmenTal saFeTY  
CauTion  
NOTICE  
„ Check with your local county or state safety towing  
regulations, in addition to meeting Department of  
Transportation (DOT) Safety Towing Regulations,  
before towing your mixer.  
„ Dispose of hazardous waste properly.  
Examples of potentially hazardous waste  
are used motor oil, fuel and fuel filters.  
„ do noT use food or plastic containers to dispose of  
hazardous waste.  
„ In order to reduce the possibility of an accident while  
transporting the mixer on public roads, alwaYs make  
sure the towing vehicle is mechanically sound and in  
good operating condition.  
„ do noT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
„ alwaYs shutdown engine before transporting.  
„ alwaYs inspect the hitch and coupling for wear. never  
tow a mixer with defective hitches, couplings, chains, etc.  
„ Check the tire air pressure on both towing vehicle and  
mixer Mixer tires should be inflated to 50 psi cold. Also  
check the tire tread wear on the vehicle and mixer.  
„ alwaYs make sure the mixer is equipped with a safety  
chain.  
„ alwaYs properly attach mixer’s safety chains to towing  
vehicle.  
„ The maximum speed for highway towing is55 mpHunless  
posted otherwise.Recommended off-road towing is not to  
exceed 15 mpH or less depending on type of terrain.  
„ Avoid sudden stops and starts.This can cause skidding,  
or jack-knifing. Smooth, gradual starts and stops will  
improve towing.  
„ Avoid sharp turns to prevent rolling.  
„ Mixer should be adjusted to a level position at all times  
when towing.  
„ Raise and lock mixer wheel stand in up position when  
towing.  
„ Place chock blocks underneath wheel to prevent rolling  
while parked.  
page 10 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
safety cHain cOnnectiOn  
2. Route the safety chain through the holes just above  
the tow bar, located on each side of the mixer stand.  
CauTion  
never tow the mixer with the safety chain removed.  
The safety chain is intended to prevent complete  
separation of the mixer from the towing vehicle in the  
event of a tow bar failure.  
Loop the chain together and place under the tow bar.  
Secure the loop with the connector link.  
3. Extend the safety chain along the length of the tow bar,  
looping it through the tow bar's connector link.Remove  
any excess chain slack.  
Tow BarTo mixer ConneCTion  
Reference Figure 1 for the installation of the safety chain.  
4. Connect the free end of (connector link) the safety  
chain to the towing vehicle. Remember it is critical that  
the length of the chain be properly adjusted, to prevent  
the draw bar and the front of the mixer stand from  
dropping to the ground (contact) in the event the draw  
bar becomes disconnected from the towing vehicle.  
1. Insert the tow bar through the round opening at the  
bottom of the mixer stand.  
Align the hole on the tow bar with the hole on the mixer  
frame, and insert 1/2-inch bolt through tow bar and  
frame.Secure tow bar to frame with 1/2-inch nyloc nut.  
Tighten to 40 ft.-lbs.  
CauTion  
do noT tow the mixer unless the mixing drum is  
completely empty. alwaYs make sure the drum latch  
pin is fully engaged to the right (Figure 2) of the drum  
stop block. This will keep the drum from rotating.  
MIXER  
STAND  
1/2-INCH NYLOCK  
NUT, GRADE 5  
SAFETY CHAIN  
STEP 2  
DRUM LATCH  
PIN  
TOW BAR  
CONNECTOR LINK  
STEP 1  
SAFETY CHAIN  
CLEVIS SAFETY HOOK  
(TOWING VEHICLE)  
1/2-INCH BOLT,  
GRADE 5  
STOP  
STEP 3  
BLOCK  
SAFETY CHAIN  
CONNECTOR LINK  
STEP 4  
TOW OR LOCKED  
POSITION  
Figure 1. Tow Bar and Safety Chain Installation  
Figure 2. Drum Latch Pin  
(Tow or Locked Position)  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
specificatiOns  
Table 1. mixer specifications  
Capacity  
Bag Capacity  
weight  
6.3 cu. ft (178 liters)  
1-1/2 to 2-1/2 bags  
574 lbs. (260 kg.)  
73 in. (185 cm.)  
17.5 in. (44.4 cm.)  
V-Belt/Gear  
Height w/dump Handle  
discharge Height  
drive  
dump action  
Manual  
Table 2. engine specifications  
Honda gx160uT1Hx2 Honda gx240uT1Ha2  
model  
Baldor  
Air-cooled 4 stroke, Single Cylinder, OHV,  
Horizontal Shaft Gasoline Engine  
1.5 HP, 115/230V Single-Phase  
Electric Motor  
Type  
2.70 in. X 1.80 in.  
(68 mm x 45 mm)  
2.90 in. X 2.30 in.  
(73 mm x 58 mm)  
Bore x stroke  
N/A  
displacement  
9.9 cu. in. (163 cc)  
14.81 cu. in. (242 cc)  
7.1 H.P./3600 R.P.M.  
N/A  
max output  
4.8 H.P./3600 R.P.M.  
1.5 HP/1725 RPM  
Approx. 0.95 U.S. Gallons  
(3.6 Liters)  
Approx. 1.59 U.S. Gallons  
(6 Liters)  
Fuel Tank Capacity  
N/A  
Fuel  
Unleaded Gasoline  
N/A  
N/A  
N/A  
N/A  
lube oil Capacity  
speed Control method  
starting method  
0.63 qt. (0.6 liter)  
1.16 qt. (1.1 liter)  
Centrifugal Flyweight Type  
Recoil Start  
12.3 x 14.3 x 13.6 in.  
(312 x 362 x 346 mm)  
15 X 17 X 16.6 in.  
(380 X 430 X 422 mm)  
13.3 X 8.7 X 9.06 in.  
(380 X 430 X 422 mm  
dimensions (l x w x H)  
dry net weight  
40.8 lbs. (15 Kg.)  
55.1 lbs. (25 Kg.)  
Approx. 22 lbs. (10 Kg.)  
NOTICE  
In accordance with our established policy of constant  
improvement, we reserve the right to amend these  
specifications at any time without notice.  
page 12 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
diMensiOns  
Table 3. dimensions  
description  
Length (w/Tow Bar)  
Width  
dimensions in. (cm)  
67 in. (170 cm)  
C
50 in. (127 cm)  
Height  
56 in. (142 cm)  
A
OPTIONAL TOW BARS  
APPROXIMATE LENGTH  
36 IN. (91.44 CM)  
HPC-1  
1-INCH  
PIN COUPLER  
HBC-1  
2-INCH  
BALL COUPLER  
HLC-1  
LOOP COUPLER  
B
Figure 3. Dimensions  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
General infOrMatiOn  
Ensure that the extension cable is carefully laid out avoiding  
wet areas, sharp edges and locations where vehicles might  
run over it.Avoid allowing the extension cable to be trapped  
underneath the mixer.  
appliCaTion  
The MQ Whiteman WM63 Series mixers (drum capacity  
of 6.3 cu. ft./178 liters) are shipped completely assembled  
and have been factory tested and are ready for use.  
Unroll the extension cable fully or it will overheat and could  
catch fire. Make sure that all extension cable connections  
are dry and safe. Replace any defective or badly worn  
extension cable immediately.  
This mixer is only intended for the production of plaster and  
mortar. The mixer must be used for its intended purpose  
and is not suitable for the mixing of flammable or explosive  
substances. The mixer must not be used in an explosive  
atmosphere.This mixer has a batch capacity between 2-1/2  
and 3-1/2 bags.  
Hardware  
Check all hardware on the mixer before starting.Periodically  
inspect all hardware. Loose hardware can contribute  
to early component failure and poor performance. Use  
Table 4 as a general guideline when torqueing of mixer  
hardware is required.Remember to keep all mixer hardware  
components tight.  
power planTs  
The WM63 Series mixer can be equipped with either a  
Honda GX160 or GX240 air-cooled, 4-stroke gasoline  
engine. In addition this mixer is also available with a 1.5  
HP electric motor with that can be configured for either  
115 or 230 VAC operation by means of a voltage selector  
switch.Refer toTable 2 for specific engine or electric motor  
information.  
Table 4. Hardware Torque recommendations  
Hardware diameter  
5/16-inch x 18  
3/8-inch x 16  
Torque (ft-lbs)  
14  
24  
37  
39  
eleCTriCal  
If mixer is equipped with an electric motor, make sure that  
the power being supplied to the motor corresponds to the  
voltage rating label on the motor. Supplying the wrong  
voltage to the electric motor will cause severe electrical  
damage to the motor.  
3/8-inch x 24  
1/2-inch x 13  
1/2-inch x 13  
(Grade 8)  
90  
Always make sure the OFF/ON switch on the electric motor  
is in the OFF position before applying power.  
engine mainTenanCe  
For basic engine maintenance, refer to the engine  
maintenance section in this manual. For a more detailed  
engine maintenance, refer to the Honda Engine Owner's  
manual furnished with the engine.  
It is strongly recommended when inserting the mixer's  
power cord into a receptacle, that a G.F.C.I. (Ground  
Fault Current Interrupter) receptacle be used (115 VAC  
applications).  
Extension Cables  
The extension cable should be a 3-wire configuration that  
includes a ground wire that conforms to UL code.The wire  
cross section must be a minimum of 2.5 mm2. Choose an  
extension cord of adequate current carrying capacity as  
referenced in Table 6. Remember cable distance affects  
the current-voltage capacity of the extension cable.  
page 14 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
cOMpOnents  
Figure 4 illustrates the basic components and controls of  
the WM63 Series mixer.  
9. safety grill — Provided for operator safety.This safety  
grill is designed to keep hands and solid objects out of  
the mixing drum when in use.This grill should be closed  
at all times when mixer is in use. do noT remove the  
grill or grill opening bar.Keep the grill clean by washing  
it down daily.  
10. dump Handle — Pull this handle downward to dump  
the contents of the drum. Push the handle upward to  
return the drum to its vertical position.  
11. safety grill lock Handle —To prevent injury to hands  
and arms, the safety grill should alwaYs be locked  
when the mixing of plaster or mortar is required. Also  
when transporting the mixer, the safety grill should be  
locked. The safety grill should only be unlocked when  
cleaning of the blades and drum is required.  
12. pivot point/Zerk Fitting — There is a zerk grease  
fitting on each end of the mixing drum. These fittings  
lubricate the dumping mechanism. Lubricate both  
fittings at least twice a week.  
Figure 4. Mixer Components  
1. Tires ply — The tire ply (layers) number is rated in  
letters. This mixer uses 13-inch 4-ply tires.  
13. dump Handle release pin — Pull this pin outward  
(spring loaded) to release the drum, then pull down  
on the dump handle to place the drum in the dump  
position. When drum is in dump position, pin will  
automatically lock drum.  
2. engine Cover — Lift this cover to gain access to the  
engine compartment.  
3. Belt slip lever — When starting, this lever should  
be move upward and to the left. For mixing, place the  
lever in the down position. See attached decal located  
adjacent to lever.  
14. mixing drum — Mixing materials such as mortar,  
plaster are to be placed into this drum for mixing.  
Always clean the drum after each use.  
4. on/oFF switch — This switch is located on the side  
of the engine cover. When activated, it will shut down  
the engine.  
15. Tow Bar/Coupler — This mixer uses a 2-inch coupler  
or pintle towbar.  
5. latch — Use this latch to secure the engine  
compartment cabinet.  
16. safety Chain — This mixer uses a 3/16-inch thick,  
72-inches long, zinc-plated safety chain. alwaYs  
connect the safety chain when towing.  
6. drum Bearing — There is a sealed bearing on  
each end of the mixing drum. Bearings are packed  
and sealed at the factory and require no further  
maintenance.  
17. Forklift pockets — When lifting of the mixer is  
required, use these fork lift pockets to lift the mixer.  
Remember to insert the forks of the forklift a minimum  
of 24 inches into the lift pockets.  
7. mixing paddles — Used in the mixing of material.This  
unit uses four different types of paddles to provide a  
fast uniform mix.  
18. Chock Blocks — Place these blocks (not included as  
part of the mixer package) under each mixer wheel to  
prevent rolling.  
8. Bag Cutter — This feature allows compound mixing  
bags to be opened easily, therefore allowing the  
contents of the bag to fall directly into the mixing drum.  
19. drum latch pin — Place pin to the right to prevent  
drum from rotating. Place pin to the left to rotate (tilt)  
drum.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
inspectiOn  
5. I  
NOTICE  
BeFore sTarTing  
1. Read all safety instructions at the beginning of manual.  
Reference engine manufacturer’s manual for specific  
servicing instructions.  
2. Clean the unit, removing dirt and dust, particularly the  
engine cooling air inlet, carburetor and air cleaner.  
UPPER LIMIT  
3. Check the air filter for dirt and dust. If air filter is dirty,  
replace air filter with a new one as required.  
4. Check carburetor for external dirt and dust. Clean with  
dry compressed air.  
5. Check fastening nuts and bolts for tightness.  
LOWER LIMIT  
Figure 6. Engine Oil Dipstick (Oil Level)  
CauTion  
alwaYs wear approved eye and hearing  
protection while operating the mixer.  
Table 5. oil Type  
season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C ~ 10°C  
0°C or Lower  
oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
CauTion  
never place hands or feet inside the  
engine guard cover while the engine is  
running. alwaYs shut the engine down  
before performing any kind of maintenance  
service on the mixer.  
Fuel CHeCk  
danger  
Motorfuelsarehighlyflammableandcanbe  
dangerous if mishandled. do noT smoke  
whilerefueling.donoTattempttorefuelthe  
mixer if the engine is hot or running.  
engine oil CHeCk  
1. To check the engine oil level, place the unit on secure  
level ground with the engine stopped.  
2. Remove the filler dipstick from the engine oil filler hole  
(Figure 5) and wipe it clean.  
1. Remove the gasoline cap located on top of fuel tank.  
2. Visually inspect to see if fuel level is low. If fuel is low,  
replenish with unleaded fuel.  
3. When refueling, be sure to use a strainer for filtration.  
do noT top-off fuel. Wipe up any spilled fuel  
immediately.  
Figure 5. Engine Oil Dipstick (Removal)  
3. Insert and remove the dipstick without screwing it into  
the filler neck.Check the oil level shown on the dipstick.  
4. f the oil level is low (Figure 6), fill to the edge of the  
oil filler hole with the recommended oil type (Table 5).  
Maximum oil capacity is 2.33 pints (1.09 liters).  
page 16 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
inspectiOn  
v-BelT CHeCk  
Check for worn or defective paddle blades (Figure 9).  
Make sure that all blades are adjusted properly. See blade  
adjustment procedure (Figure 13) in this manual. Replace  
all defective or damaged blades immediately.  
Visually examine the V-belt (Figure 7) and determine if it  
is full of tiny cracks, frayed, has pieces of rubber missing,  
is peeling or otherwise damaged.  
Also, examine the belt and determine if it is oil soaked or  
"glazed " (hard shiny appearance on the sides of the belt).  
Either of these two conditions can cause the belt to run hot,  
which can weaken it and increase the danger of it breaking.  
If the V-belt exhibits any of the above wear conditions  
replace the V-belt immediately.  
OIL SOAKED  
S
BLADE  
I
D
E
S
C
R
A
P
E
R
PADDLE  
CRACKS  
CORD FAILURE  
MISSING  
RUBBER  
GLAZED  
WORN BACK  
COVER  
Figure 9. Blade Inspection  
grease FiTTings (dumping meCHanism)  
BROKEN  
Check the drum bearing bracket grease fittings (Figure 10) at  
each end of the mixing drum.These grease fittings lubricate  
the dumping mechanism. If the dumping handle is stiff or  
hard to move, lubricate these grease fittings.  
MISSING RUBBER  
CRACKS  
SIDEWALL  
WEAR  
Figure 7. V-Belt Inspection  
GREASE  
FITTING  
sTarT/sTop swiTCH  
This unit has been equipped with a start/stop switch  
(Figure 8), which should be tested every time the unit is  
started.  
CAP  
PULL OUT  
TO START ENGINE  
DRUM  
BEARING  
BRACKET  
START/STOP  
SWITCH  
Figure 10. Grease Fittings  
Drum Bearing Bracket  
PUSH IN  
TO STOP ENGINE  
Figure 8. Start/Stop SwitchBlade CHeCk  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
basic enGine  
2. Throttle lever — Used to adjust engine RPM speed  
(lever advanced forward SLOW, lever back toward  
operator FAST).  
1
10  
9
3. engine on/oFF switch — ON position permits engine  
starting, OFF position stops engine operations.  
2
4. recoil starter (pull rope) — Manual-starting method.  
Pull the starter grip until resistance is felt, then pull  
briskly and smoothly.  
3
8
5. Fuel valve lever — OPEN to let fuel flow, CLOSE to  
stop the flow of fuel.  
7
6. Choke lever — Used in the starting of a cold engine,  
or in cold weather conditions. The choke enriches the  
fuel mixture.  
6
5
7. air Cleaner — Prevents dirt and other debris from  
entering the fuel system. Remove wing-nut on top of  
air filter cannister to gain access to filter element.  
4
Figure 11. Engine Components  
NOTICE  
iniTial serviCing  
Operating the engine without an air filter, with a  
damaged air filter, or a filter in need of replacement will  
allow dirt to enter the engine, causing rapid engine wear.  
The engine (Figure 11) must be checked for proper  
lubrication and filled with fuel prior to operation.Refer to the  
engine manufacturer’s manual for instructions and details  
of operation and servicing.  
warning  
1. Fuel Filler Cap — Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tightened  
securely. do noT over fill.  
Engine components can generate extreme  
heat. To prevent burns, do noT touch  
these areas while the engine is running or  
immediatelyafteroperating.neveroperate  
the engine with the muffler removed.  
danger  
Adding fuel to the tank should be done  
only when the engine is stopped and has  
had an opportunity to cool down. In the  
event of a fuel spill, do noT attempt to  
start the engine until the fuel residue has  
been completely wiped up, and the area surrounding  
the engine is dry.  
8. spark plug — Provides spark to the ignition system.  
Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch)  
Clean spark plug once a week.  
9. muffler — Used to reduce noise and emissions.  
10. FuelTank — Holds unleaded gasoline. For additional  
information refer to engine owner's manual.  
page 18 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
electric MOtOr  
eleCTriC moTor  
Table 6. electric motor wiring information  
115-230 vaC - single phase  
motor  
Horsepower  
rating  
For maintenance care and operation of the electric motor,  
refer to your electric motor instruction booklet furnished  
with the motor.  
NEMA  
Plug  
Mating NEMA  
Receptacle  
1.5 HP  
(115 VAC)  
L5-20P  
P/N EM940537  
L5-20R  
P/N EM940538  
Protect the electric motor from dust as much as possible  
and keep ventilating openings clean.  
1.5 HP  
(230 VAC)  
L6-20P  
P/N EM940539  
L6-20R  
P/N EM940540  
CauTion  
do noT spray water at any time on the electric motor.  
donoToperateelectricmotorinaexplosiveenvironment.  
VOLTAGE  
SELECTOR  
SWITCH  
OFF/ON  
SWITCH  
The electric motor used in this mixer is a single-phase 3  
HP motor. The input voltage requirement for this motor is  
115/230 VAC, and has been pre-set to 230VAC.  
SINGLE  
PHASE  
L5-20P PLUG  
(115 VAC)  
115/230 VAC  
ELECTRIC  
MOTOR  
2.0 HP  
eleCTriC moTor ConneCTion  
VOLTAGE  
LOCKOUT  
BOLT  
A 12-inch electrical cable (Figure 7) is provided with the  
electrical motor for hookup to a power source.Table 5 shows  
the required NEMA connector for the desired motor  
horsepower rating. In addition, Table 5 also shows the  
matching NEMA approved connector for the required  
extension cord.  
L6-20P PLUG  
(230 VAC)  
GREASE  
FITTING  
CONNECT  
TO POWER  
SOURCE  
NOTICE  
L5-20R  
RECEPTACLE  
(115 VAC)  
VOLTAGE  
SELECTOR  
SWITCH  
alwaYsmakecertainthatthepowersourcerequiredfor  
the electric motor is correct and always use the correct  
NEMA configuration plug. Failure to supply the correct  
voltage to the motor can severely damage the motor.  
VOLTAGE  
LOCKOUT  
BOLT  
G
W
NOTICE  
L6-20R  
RECEPTACLE  
(230 VAC)  
It is strongly recommended that all electrical wiring be  
done by a licensed electrician.  
Figure 12. Single Phase Electric Motor With  
12-inch Pigtail  
Special attention should be given to the electric switch as  
well as the over-and-under voltage protection devices as  
per regulations set forth in the local electrical safety code  
handbook.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
electric MOtOr  
The electric motor supplied is wired for 115 VAC grounded  
operation. Make certain that the correct size grounded  
(3-wires) extension cord is used. See Table 7 below.  
Table 7. recommended extension Cord sizes  
50 ft.  
(15.24 m) (22.86 m) (30.48 m)  
75 ft.  
100 ft.  
200 ft.  
(60.96 m)  
Model  
Motor  
Voltage  
115 VAC  
230 VAC  
No. 12  
No. 14  
No. 10  
No. 12  
No. 8  
No. 6  
No. 8  
WM63E  
1.5 HP  
No. 12  
Motors can burn out when the line voltage falls 10% below  
the voltage rating of the motor.Failure to use proper voltage  
will cause the motor to overheat and actuate the overload  
switch.  
If overload protection should actuate because of improper  
voltage or any other malfunction, turn the main switch on  
the motor to the "OFF" position and correct the problem,  
press the reset switch button, and turn the main switch to  
the "ON" position.  
eleCTriC moTor volTage swiTCH  
„ alwaYs make certain the electric motor switch is "OFF"  
and the power cord has been disconnected from the  
power source.  
„ Remove the voltage lock-out bolt (Figure 12). Change  
the position of the voltage change toggle switch from  
115 VAC to 230 VAC. The mixer is factory wired for 115  
VAC operation.  
„ Replace the voltage lock-out bolt.  
„ Important!, when changing the input voltage to the motor  
from 115 to 230 VAC, the plug on the motor power cord  
must also be changed. See Table 6  
page 20 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
paddle blade adjustMent  
Adjust paddles as shown in Figure 13.  
TOW END  
CAST PADDLE  
CENTER TOW END  
CAST PADDLE  
DRUM END  
ENGINE END  
CAST PADDLE  
PADDLE BLADE IS TOO  
TIGHT AGAINST DRUM  
SIDE WALLS.  
DRUM SIDE  
CENTER ENGINE  
END CAST PADDLE  
INCORRECT  
INCORRECT  
CORRECT  
INCORRECT  
CORRECT  
SIDE PADDLE BLADE  
PADDLE BLADE IS TOO  
TIGHT AGAINST DRUM  
SIDE WALLS.  
ROTATION  
DRUM END AND SIDE WALLS  
Figure 13. Paddle Blade Adjustment  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
start-up  
This section is intended to assist the operator with the initial  
start-up of the unit.It is extremely important that  
this section be read carefully before attempting  
to use the mixer in the field. do noT use your  
mixeruntilthissectionisthoroughlyunderstood.  
3. Move the throttle lever (Figure 16) away from the slow  
position, about 1/3 of the way toward the fast position.  
warning  
Failure to understand the operation of the mixer could  
result in severe damage to the mixer or personal injury.  
See Figure 4 for the location of any control referenced  
in this manual.  
Figure 16. Throttle Lever  
CauTion  
4. Turn the engine switch (Figure 17) to the ON position.  
never operate the mixer in a confined  
area or enclosed area structure that does  
not provide ample free flow of air.  
The following steps outline the procedure for starting the  
engine.  
1. Move the fuel shut-off lever (Figure 14) to the ON  
position.  
Figure 17. Engine On/Off Switch  
5. The main start/stop switch located on the engine cover  
(Figure 18) is used to start and stop the engine. Pull  
this switch outward to start the engine.  
PULL OUT  
Figure 14. Fuel Shut-Off Lever  
TO START ENGINE  
2. To start a cold engine, move the choke lever (Figure  
15) to the CLOSED position.  
Figure 18. Start/Stop Switch  
Figure 15. Choke Lever  
page 22 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
start-up  
DRUM LATCH  
PIN  
6. Place the belt slip lever (Figure 19) in the START/STOP  
(disengaged) position.  
START/STOP  
POSITION  
STOP  
BLOCK  
TOW OR LOCKED  
POSITION  
BELT SLIP  
LEVER  
Figure 21. Drum Lock Pin (Right Position)  
7. Pull the starter grip (Figure 22) lightly until you feel  
resistance, then pull briskly. Return the starter grip  
gently.  
Figure 19. Belt Slip Lever  
(Start/Stop Position)  
CauTion  
Make certain the drum lock pin (Figure 20  
andFigure21)isplacedtotheRIGHT(when  
viewing the mixer from the towpole end) of  
the drum stop block which is welded to the  
front side of the drum. Also make sure lock pin is fully  
engaged (locked).This will prevent the drum from tipping.  
Figure 22. Starter Grip  
8. Place the belt slip lever (Figure 23) in the mix position.  
This will tilt the engine placing tension on the V-belts  
enabling the shaft to rotate.  
LOCK  
PIN  
FRONT  
POST  
MIX  
POSITION  
DRUM  
Figure 20. Drum Lock Pin (Side-View)  
BELT SLIP  
LEVER  
Figure 23. Belt Slip Lever (Mix Position)  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OperatiOn  
STAND CLEAR OF DUMP HANDLE.  
HANDLE KICK-BACK IS POSSIBLE.  
mixing/dumping  
1. The paddle shaft inside the drum should be rotating  
at this time.  
2. Add a small amount water to the mixing drum.  
3. Lift the mixing bag compound onto the steel safety  
grate over the bag cutter and let the contents fall into  
the drum.Add more water if desired and mix compound  
to desired consistency.  
4. When charging, mixing, or dumping a batch of plaster  
or mortar the drum lock pin should be placed to the left  
(when viewing the mixer from the towpole end) of the  
drum stop block which is welded to the front side of  
the drum. See Figure 24.  
Figure 25. Stand Clear of Dump Handle  
sTopping THe mixer (gasoline)  
DRUM LATCH  
PIN  
STOP  
BLOCK  
1. Place the belt slip lever in the start/stop position (Figure  
19).  
2. Push the main start/stop switch (Figure 18) inward to  
stop the engine.  
3. Turn the fuel shut-off valve to the OFF position.  
4. Disconnect the spark plug.  
MIX  
POSITION  
5. Clean mixer as referenced in the maintenance section  
of this manual.  
Figure 24. Drum Lock Pin (Left Position)  
NOTICE  
This will allow the operator to use both hands on the drum  
handle during dumping.Please note that when the lock pin  
is placed to the left, the drum will be maintained in the  
vertical position as the paddles rotate. To discharge the  
material the operator should hold the dump handle with  
both hands and rotate the drum to discharge the desired  
amount of material.  
It is recommended that the mixer’s Start/Stop switch be  
used to stop the engine after every use. Doing this will  
verify that the switch is working properly and presents  
no danger to the operator.  
danger  
never disable or disconnect the start/stop switch.It is  
provided for operator safety.Serious Injury may result if  
it is disabled, disconnected or improperly maintained.  
warning  
Be sure to stand clear of the dump handle (Figure 25)  
when the mixer is operational. Any binding of material  
between the mixer blades and the drum will cause the  
dumphandletoquicklymoveandcouldcausebodilyharm.  
sTopping THe mixer (eleCTriC moTor)  
1. Place the electric motor's ON/OFF switch (Figure 12)  
in the OFF position  
2. Disconnect the electric motor's extension cord from  
its power source.  
3. Clean mixer as referenced in the maintenance section  
of this manual.  
page 24 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
nOtes  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (enGine)  
UseTable 8 as a general maintenance guideline when servicing your engine.For more detail engine maintenance information,  
refer to the engine owner’s manual supplied with your engine.  
Table 8. engine maintenance schedule  
everY  
FirsT everY 3  
operaTion BeFore monTH or monTHs  
everY 6  
monTHs  
or 25 Hrs. or 50 Hrs.  
everY 2  
Years or  
200 Hrs.  
desCripTion  
(3)  
Year  
or 100  
Hrs.  
10 Hrs.  
Check  
Change  
Check  
X
X
Engine Oil  
Air Cleaner  
X
Change  
X (1)  
All Nuts and Re-tighten if  
X
Bolts  
necessary  
Check/Clean  
Replace  
Check  
X
X
Spark Plugs  
X
Cooling Fins  
Spark Arrester  
Fuel Tank  
Clean  
X
X
X
Clean  
Fuel Filter  
Check  
Check/  
Adjust  
Idle Speed  
X (2)  
Valve  
Clearance  
Check/  
Adjust  
X (2)  
Fuel Lines  
Check  
Every 2 years (replace if necessary) (2)  
(1) Service more frequently when used in dusTY areas.  
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically  
proficient. Refer to the HONDA Shop Manual for service procedures.  
(3) For commercial use, log hours of operation to determine proper maintenance intervals.  
page 26 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (enGine)  
Perform the scheduled maintenance procedures as defined  
by Table 8 and below:  
OIL FILLER CAP  
DIPSTICK  
dailY  
„ Thoroughly remove dirt and oil from the engine and  
control area. Clean or replace the air cleaner elements  
as necessary. Check and retighten all fasteners as  
necessary. Check the gearbox for oil leaks. Repair or  
replace as needed.  
SEALING  
WASHER  
DRAIN  
BOLT  
Figure 27. Engine Oil (Draining)  
weeklY  
engine air Cleaner  
„ Remove the fuel filter cap and clean the inside of the  
fuel tank.  
1. Remove the air cleaner cover and foam filter element  
as shown in Figure 28.  
„ Remove or clean the filter at the bottom of the tank.  
2. Tap the paper filter element (Figure 28) several times  
on a hard surface to remove dirt, or blow compressed  
air [not exceeding 30 psi (207 kPa, 2.1 kgf/cm2)]  
through the filter element from the air cleaner case  
side. NEVER brush off dirt. Brushing will force dirt  
into the fibers. Replace the paper filter element if it is  
excessively dirty.  
„ Remove and clean the spark plug (Figure 26), then adjust  
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This  
unithaselectronicignition, whichrequiresnoadjustments.  
GAP  
0.024-0.028 IN.  
(0.6-0.7 MM.)  
3. Clean foam element in warm, soapy water or  
nonflammable solvent. Rinse and dry thoroughly. Dip  
the element in clean engine oil and completely squeeze  
out the excess oil from the element before installing.  
danger  
Figure 26. Spark Plug Gap  
do noT use gasoline as a cleaning solvent to avoid  
creating the risk of fire or an explosion.  
engine oil  
1. Drain the engine oil when the oil is warm as shown in  
Figure 27.  
2. Remove the oil drain bolt and sealing washer and allow  
the oil to drain into a suitable container.  
3. Replace engine oil with recommended type oil as listed  
in Table 5. For engine oil capacity, see Table 2 (Engine  
Specifications). do noT overfill.  
4. Install drain bolt with sealing washer and tighten  
securely.  
Figure 28. Engine Air Cleaner  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
drum Head seals  
There is 1 set of drum head seals (Figure 29) that will  
require lubrication. Lubricate the grease fitting for each  
drum seal every 40 hours of operation using any grade  
lithium base grease. Apply grease until visible inside of  
mixing drum (over grease). This will purge seal system of  
contamination.  
DRUM BEARING  
BRACKET  
Figure 30. Grease Fittings (Dumping  
Mechanism)  
CauTion  
Failure to lubricate the drum bearing grease fittings  
periodically will cause the dumping mechanism to  
stiffen, making the mixing drum hard to dump.  
Figure 29. Grease Fittings (Drum Head Seals)  
Ball soCkeT and Clamp FaCe mainTenanCe  
drum Bearing BraCkeT luBriCaTion  
1. If the towing vehicle is equipped with a ball socket,  
smear socket periodically with multi-purpose grease.  
This will keep the ball socket well lubricated.  
There is 1 set of drum bearing brackets (Figure 30) that  
will require lubrication. These brackets are intended to  
make the drum rotate freely. Lubricate the grease fitting  
for each drum bearing bracket every month or when the  
drum becomes difficult to position using multi-purpose  
grade grease.  
2. Periodically oil pivot points and clamp face surfaces of  
coupler with SAE 30 WT. motor oil.  
3. When parking or storing your mixer. Keep the coupler  
off the ground so dirt will not build up in the ball socket.  
CounTersHaFT Bearing luBriCaTion  
There is 1 set of countershaft bearings (Figure 31) that  
will require lubrication.Lubricate the grease fitting for each  
countershaft bearing every 40 hours of operation using any  
grade lithium base grease.  
page 28 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
main gear and drive pinion alignmenT  
1. Disconnect the spark plug wire (gasoline engines). If  
mixer is equipped with an electric motor remove power  
cord from AC power receptacle.In addition make sure  
the clutch engagement lever is disengaged to relieve  
V-belt tension.  
GREASE FITTING  
AND CAP  
2. The countershaft and drive pinion are mounted on a  
slotted base.To align drive pinion with main gear, loosen  
the pillow block mounting bolts and move them until  
the necessary alignment has been made. Remember  
gears must be paralleled aligned not skewed.  
Figure 31. Grease Fittings (Countershaft)  
wHeel Bearings  
3. Using your hand, slightly move (rock) the drive pulley  
back and forth to determine the amount of backlash.  
Insert feeler gauge between gears to determine  
backlash distance. Backlash should range between  
0.007- 0.012 inches (Figure 33).  
1. After every 3 months of operation, remove the hub dust  
cap and inspect the wheel bearings (Figure 32). Once  
a year, or when required, disassemble the wheel hubs  
remove the old grease and repack the bearings forcing  
grease between rollers, cone and cage with a good  
grade of high speed wheel bearing grease (never use  
grease heavier than 265 A.S.T.M.penetration (“No.2.”).  
MAIN GEAR  
BEARING  
CONE  
WHEEL  
MAIN GEAR  
GEAR TEETH  
HUB  
DRIVE  
PINION  
OIL  
SEAL  
PINION GEAR  
BEARING  
CUP  
0.007 - 0.012 INCHES  
(MAX. BACKLASH)  
Figure 33. Drive Pinion and Main Gear  
(Backlash)  
Figure 32. Wheel Hub and Bearings  
inspeCTTooTH ConTaCT BeTweenmaingear  
and drive pinion  
2. Fill the wheel hub (Figure 32) with grease to the inside  
diameter of the outer races and also fill the hub grease  
cap. Reassemble the hub and mount the wheel. Then  
tighten the adjusting nut, at the same time turn the  
wheel in both directions, until there is a slight bind to  
be sure all the bearing surfaces are in contact.  
1. Coat 3 or 4 teeth at 3 different positions on the main  
gear with yellow paint.  
2. Rotate the drive pulley in both directions.  
3. Inspect the tooth pattern.  
Then back-off the adjusting nut 1/6 to 1/4 turn or to the  
nearest locking hole or sufficiently to allow the wheel  
to rotate freely within limits of .001” to .010” end play.  
Lock the nut at this position. Install the cotter pin and  
dust cap, and tighten all hardware.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
4. If gear teeth are not contacting properly (Figure 34),  
adjust pillow block to correct the problem.  
HEAL  
GREASE  
FITTING  
CONTACT  
FACE  
CONTACT  
PROPER  
CONTACT  
TOE  
CONTACT  
FLANK  
CONTACT  
Figure 34. Gear Teeth Alignment  
gear luBriCaTion  
Figure 36. Grease Fittings Electric Motor  
The surface of the pinion and main gear (Figure 35) should  
be very lightly greased.  
Tires/wHeels/lug nuTs  
Tires and wheels are a very important and critical  
components of the trailer. When specifying or replacing  
the trailer wheels it is important the wheels, tires, and axle  
are properly matched.  
warning  
MAIN  
donoTattempttorepairormodifyawheel.  
donoTinstallaninter-tubetocorrectaleak  
through the rim. If the rim is cracked, the air  
pressure in the inter-tube may cause pieces  
of the rim to explode (break-off) with great force and can  
cause serious eye or bodily injury.  
GEAR  
DRIVE  
PINION  
Figure 35. Pinion and Bull Gear Lubrication  
NOTICE  
Grease main and pinion gears every 250 hours of  
operation. avoid over-greasing. Excess grease will  
accumulate contaminants and cause premature wear.  
Tires wear/inflation  
Tire inflation pressure is the most important factor in tire  
life. Pressure should be checked cold before operation.  
do noT bleed air from tires when they are hot. Check  
inflation pressure weekly during use to insure the maximum  
tire life and tread wear.  
grease FiTTings (Zerk) mainTenanCe  
(eleCTriC moTor)  
1. There are two grease (Figure 33) fittings at each end of  
the electric motor that will require lubrication.Lubricate  
these fittings about every 16 months.  
warning  
alwaYswearsafetyglasseswhenremoving  
or installing force fitted parts. Failure to  
comply may result in serious injury.  
2. Use Poleyrex EM (Exxon Mobil) or equivalent lubricant.  
Clean grease fitting, apply grease gun to fitting (1/2  
shot). Remember too much grease or injecting grease  
too quickly can cause premature bearing failure.Slowly  
apply the recommended amount of grease, taking a  
minute or so to apply.  
Table 9 (Tire Wear Troubleshooting) will help pinpoint the  
causes and solutions of tire wear problems.  
page 30 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
3. After first road use, retorque all lug nuts in sequence.  
Check all wheel lug nuts periodically.  
Table 9. Tire wear Troubleshooting  
Wear Pattern  
Cause  
Solution  
Adjust pressure to  
Over Inflation particular load per  
tire manufacturer  
Center  
Wear  
1
1
4
3
Adjust pressure to  
Under  
6
4
3
5
Edge  
Wear  
particular load per  
Inflation  
2
tire manufacturer.  
2
Loss of  
chamber or  
overloading  
Make sure load does  
not exceed axle  
rating. Align wheels.  
Side  
Wear  
4-LUG NUTS  
6-LUG NUTS  
Toe  
Wear  
Incorrect  
toe-in  
Align wheels.  
Check bearing  
adjustment and  
balance tires.  
Out of  
balance  
Cupping  
1
1
3
6
4
2
3
Wheel lockup Avoid sudden stops  
and tire  
skidding  
8
7
Flat  
Spots  
when possible and  
adjust brakes.  
5
5
4
2
lug nut Torque requirements  
8-LUG NUTS  
LUG NUTS  
5-LUG NUTS  
It is extremely important to apply and maintain proper  
wheel mounting torque. Be sure to use only the fasteners  
matched to the cone angle of the wheel. Proper procedure  
for attachment of the wheels is as follows:  
1. Start all wheel lug nuts by hand.  
2. Torque all lug nuts in sequence.See Figure 37. do noT  
torque the wheel lug nuts all the way down.Tighten each  
lug nut in 3 separate passes as defined by Figure 37.  
Table 10. Tire Torque requirements  
First pass  
FT-lBs  
second pass  
FT-lBs  
Third pass  
FT-lBs  
wheel size  
12"  
13"  
14"  
15"  
16"  
20-25  
20-25  
20-25  
20-25  
20-25  
35-40  
35-40  
50-60  
50-60  
50-60  
50-65  
50-65  
90-120  
90-120  
90-120  
PNEUMATIC  
AIR GUN  
TORQUE WRENCH  
NOTICE  
never use an pneumatic air gun to tighten wheel  
lug nuts.  
Figure 37. Wheel Lug Nuts Tightening  
Sequence  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
suspension  
The rigid type axle and associated hardware (Figure 38)  
should be periodically inspected for signs of excessive  
wear, elongation of bolt holes, and loosening of fasteners.  
Replace all damaged parts immediately.  
Figure 39. No Spraying of Water  
warning  
When rotating the mixing drum from the dump position  
to the upright position, keep hands clear of safety grate.  
The possibility exists of hands or fingers being crushed  
(Figure 40).  
CHECK FOR  
TIGHTNESS  
CRUSH HAZARD AREA. KEEP HANDS  
AND FINGERS CLEAR OF SAFETY  
GRATE AT ALL TIMES.  
RIGID TYPE  
AXLE  
Figure 38. Axle Support Components  
mixer Cleaning  
1. alwaYs disconnect the spark plug wire (gasoline  
engines) before cleaning the inside of the drum.If mixer  
is equipped with an electric motor remove power cord  
from AC power receptacle. In addition make sure the  
clutch engagement lever is dis-engaged.  
2. Make sure the rear section of the safety grate is  
connected to the mixing drum.  
3. At the end of each day’s operation, place mixer drum in  
an upright position and spray inside of tub immediately  
with water to prevent lumps of dried mortar or plaster  
from forming and contamination of future batches, do  
noT allow a buildup of materials to form on the blades  
or anywhere inside the drum.  
Figure 40. Safety Grate (Crush Hazard)  
7. When cleaning of the entire mixer is done, return mixing  
drum to an upright position.  
4. Rotate mixer to dump position and remove debris.  
5. Thoroughly clean the entire mixer, wheels, cabinet  
and frame.  
6. never pour or spray water over the engine or electric  
motor (Figure 39).  
page 32 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance (Mixer)  
mixer sTorage  
For storage of the mixer for over 30 days, the following is  
recommended:  
„ Drain the fuel tank completely, or add STA-BIL to the fuel.  
„ Run the engine until the fuel is completely consumed.  
„ Completely drain used oil from the engine crankcase  
and fill with fresh clean oil, then follow the procedures  
described in the engine manual for engine storage.  
„ Clean the entire mixer and engine compartment.  
„ Place the mixing drum in the down position (mouth facing  
downward).  
„ Cover the mixer and place it a clean dry area, that is  
protected from harsh elements.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
trOublesHOOtinG  
Troubleshooting (engine)  
symptom  
possible problem  
solution  
Spark plug bridging?  
Check gap, insulation or replace spark plug.  
Clean or replace spark plug.  
Carbon deposit on spark plug?  
Short circuit due to deficient spark plug  
insulation?  
Check spark plug insulation, replace if worn.  
Improper spark plug gap?  
Fuel reaching carburetor?  
Water in fuel tank?  
Set to proper gap.  
Check fuel line.  
Flush or replace fuel tank.  
Replace fuel filter.  
Fuel filter clogged?  
Stuck carburetor?  
Check float mechanism.  
Check transistor ignition unit.  
Difficult to start, fuel is available, but no spark at  
spark plug.  
Spark plug is red?  
If insufficient compression, repair or replace  
engine. If injected air leaking, correct leak. If  
carburetor jets clogged, clean carburetor.  
Spark plug is bluish white?  
Check transistor ignition unit is broken, and  
replace defective unit. Check if voltage cord  
cracked or broken and replace. Check if spark  
plug if fouled and replace.  
No spark present at tip of spark plug?  
No oil?  
Add oil as required.  
Oil pressure alarm lamp blinks upon starting? (if Check automatic shutdown circuit, "oil sensor".  
applicable)  
(if applicable)  
ON/OFF switch is shorted?  
Check switch wiring, replace switch.  
Replace ignition coil.  
Ignition coil defective?  
Difficult to start, fuel is available, and spark is  
present at the spark plug.  
Improper spark gap, points dirty?  
Condenser insulation worn or short circuiting?  
Spark plug wire broken or short circuiting?  
Set correct spark gap and clean points.  
Replace condenser.  
Replace defective spark plug wiring.  
Flush fuel system, replace with correct type of  
fuel.  
Wrong fuel type?  
Difficult to start, fuel is available, spark is  
present and compression is normal.  
Water or dust in fuel system?  
Air cleaner dirty?  
Flush fuel system.  
Clean or replace air cleaner.  
Close choke.  
Choke open?  
Suction/exhaust valve stuck or protruded?  
Piston ring and/or cylinder worn?  
Reseat valves.  
Replace piston rings and/or piston.  
Difficult to start, fuel is available, spark is  
present and compression is low.  
Cylinder head and/or spark plug not tightened  
properly?  
Torque cylinder head bolts and spark plug.  
Head gasket and/or spark plug gasket damaged?  
No fuel in fuel tank?  
Replace head and spark plug gaskets.  
Fill with correct type of fuel.  
Apply lubricant to loosen fuel cock lever,  
replace if necessary.  
Fuel cock does not open properly?  
No fuel present at carburetor.  
Fuel filter/lines clogged?  
Fuel tank cap breather hole clogged?  
Air in fuel line?  
Replace fuel filter.  
Clean or replace fuel tank cap.  
Bleed fuel line.  
page 34 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
trOublesHOOtinG  
Troubleshooting (engine) - continued  
symptom  
possible problem  
solution  
Clean or replace air cleaner.  
Check float adjustment, rebuild carburetor.  
Clean or replace spark plug.  
Set to proper gap.  
Air cleaner dirty?  
Improper level in carburetor?  
Defective spark plug?  
Weak in power, compression is proper and  
does not misfire.  
Improper spark plug?  
Flush fuel system and replace with correct  
type of fuel.  
Water in fuel system?  
Weak in power, compression is proper but  
misfires.  
Dirty spark plug?  
Clean or replace spark plug.  
Replace ignition coil.  
Ignition coil defective?  
Spark plug heat value incorrect?  
Wrong type of fuel?  
Replace with correct type of spark plug.  
Replace with correct type of fuel.  
Clean cooling fins.  
Cooling fins dirty?  
Engine overheats.  
Clear intake of dirt and debris. Replace air  
cleaner elements as necessary.  
Intake air restricted?  
Oil level too low or too high?  
Governor adjusted incorrectly?  
Governor spring defective?  
Fuel flow restricted?  
Adjust oil to proper level.  
Adjust governor.  
Rotational speed fluctuates.  
Replace governor spring.  
Check entire fuel system for leaks or clogs.  
Recoil mechanism clogged with dust and dirt? Clean recoil assembly with soap and water.  
Recoil starter malfunctions. (if applicable)  
Spiral spring loose?  
Replace spiral spring.  
Ensure tight, clean connections on battery  
and starter.  
Loose, damaged wiring?  
Starter malfunctions.  
Battery insufficiently charged?  
Recharge or replace battery.  
Replace starter.  
Starter damaged or internally shorted?  
Check and clean valves. Check muffler and  
replace if necessary.  
Over-accumulation of exhaust products?  
Wrong spark plug?  
Burns too much fuel.  
Replace spark plug with manufacturer's  
suggested type.  
Lubricating oil is wrong viscosity?  
Worn rings?  
Replace lubricating oil with correct viscosity.  
Replace rings.  
Exhaust color is continuously "white".  
Air cleaner clogged?  
Clean or replace air cleaner.  
Adjust choke valve to correct position.  
Choke valve set to incorrect position?  
Carburetor defective, seal on carburetor  
broken?  
Exhaust color is continuously "black".  
Replace carburetor or seal.  
Poor carburetor adjustment, engine runs too  
rich?  
Adjust carburetor.  
ON/OFF device not activated ON?  
Battery disconnected or discharged?  
Ignition switch/wiring defective?  
Turn on ON/OFF device.  
Check cable connections. Charge or replace  
battery  
Will not start, no power with key "ON". (if  
applicable)  
Replace ignition switch. Check wiring.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
trOublesHOOtinG  
mixer Troubleshooting  
Worn or defective V-belt?  
Replace V-belt.  
Blades will not rotate.  
Check position of adjustment lever.  
Adjust if necessary.  
Adjustment lever mis-aligned?  
Material leaking from drum ends.  
Worn or defective paddle shaft seals? Replace seals.  
Defective or worn drum support  
brackets?  
Apply grease to bracket or replace.  
Drum difficult to discharge (tilt)  
Adjust blades until they almost touch  
side walls of drum.  
Blades adjusted too tight.  
page 36 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WirinG diaGraM  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
explanatiOn Of cOde in reMarks cOluMn  
The following section explains the different symbols and  
QTY. Column  
remarks used in the Parts section of this manual. Use the  
help numbers found on the back page of the manual if there  
are any questions.  
numbers used — Item quantity can be indicated by a  
number, a blank entry, or A/R.  
A/R (As Required) is generally used for hoses or other  
parts that are sold in bulk and cut to length.  
NOTICE  
The contents and part numbers listed in the parts  
section are subject to change without notice.Multiquip  
does not guarantee the availability of the parts listed.  
A blank entry generally indicates that the item is not sold  
separately.Other entries will be clarified in the“Remarks”  
Column.  
sample parTs lisT  
remarks Column  
no. parT no. parT name  
QTY. remarks  
Some of the most common notes found in the “Remarks”  
Column are listed below. Other additional notes needed  
to describe the item can also be shown.  
1
2%  
12345  
BOLT .....................1 .....INCLUDES ITEMS W/%  
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELY  
WASHER, 3/8 IN. ..1 .....MQ-45T ONLY  
2% 12347  
3
4
12348  
12349  
HOSE ..................A/R ...MAKE LOCALLY  
BEARING ..............1 .....S/N 2345B AND ABOVE  
assembly/kit — All items on the parts list with the  
same unique symbol will be included when this item is  
purchased.  
no. Column  
Indicated by:  
unique symbols — All items with same unique  
symbol  
“INCLUDES ITEMS W/(unique symbol)”  
(@, #, +, %, or >) in the number column belong to the  
same assembly or kit, which is indicated by a note in the  
“Remarks” column.  
serial number Break — Used to list an effective serial  
number range where a particular part is used.  
Indicated by:  
duplicate item numbers — Duplicate numbers indicate  
multiple part numbers, which are in effect for the same  
general item, such as different size saw blade guards in  
use or a part that has been updated on newer versions  
of the same machine.  
“S/N XXXXX AND BELOW”  
“S/N XXXX AND ABOVE”  
“S/N XXXX TO S/N XXX”  
specific model number use — Indicates that the part  
is used only with the specific model number or model  
number variant listed. It can also be used to show a  
part is NOT used on a specific model or model number  
variant.  
NOTICE  
When ordering a part that has more than one item  
number listed, check the remarks column for help in  
determining the proper part to order.  
Indicated by:  
“XXXXX ONLY”  
“NOT USED ON XXXX”  
parT no. Column  
numbers used — Part numbers can be indicated by a  
number, a blank entry, or TBD.  
“make/obtain locally” — Indicates that the part can  
be purchased at any hardware shop or made out of  
available items.Examples include battery cables, shims,  
and certain washers and nuts.  
TBD (To Be Determined) is generally used to show a  
part that has not been assigned a formal part number  
at the time of publication.  
“not sold separately”— Indicates that an item cannot  
be purchased as a separate item and is either part of an  
assembly/kit that can be purchased, or is not available  
for sale through Multiquip.  
A blank entry generally indicates that the item is not sold  
separately or is not sold by Multiquip. Other entries will  
be clarified in the “Remarks” Column.  
page 38 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
suGGested spare parts  
wm63-series plasTer and morTar mixer wiTH  
Honda gx160uT1Hx2/gx240uT1Ha2 engines and 1.5 Hp eleCTriC moTor.  
1 to 3 units  
Qty.  
p/n  
description  
6............491107..................V-BELT A32, HONDA ENGINE (GX160, 5.5 HP)  
6............07055-034 ............V-BELT 4L340, HONDA ENGINE (GX240, 8.0 HP)  
6............491112..................V-BELT A40, ELECTRIC MOTOR  
2............EM914288 ............OIL SEAL, AXLE  
4............EM903113 ............BEARING, CONE, AXLE  
4............EM903012 ............BEARING, CUP, AXLE  
2............20654-001 ............SEAL, PADDLE SHAFT (BLACK)  
2............530029..................RING, RETENTION  
2............20104-002 ............SEAL, SHAFT URETHANE (YELLOW)  
3............17210ZE1822.......ELEMENT, AIR CLEANER (GX160, 5.5 HP)  
3............17210ZE2822.......ELEMENT, AIR CLEANER (GX240, 8.0 HP)  
3............9807956846..........SPARK PLUG, BPR6ES, NGK  
3............9807956855..........SPARK PLUG, W20EPR-U, DENSO  
1............28462ZH8003.......ROPE, RECOIL STARTER (GX160, 5.5 HP)  
1............28462ZE2W11......ROPE, RECOIL STARTER (GX240, 8.0 HP)  
1............17620Z4H020.......CAP, FUEL TANK  
2............25647-502 ............KIT, WIPER BLADES (STEEL DRUM)  
NOTICE  
Part numbers on this Suggested Spare Parts list may  
supersede/replace the part numbers shown in the  
following parts lists.  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
naMeplate and decals  
SAFETY  
INSTRUCTIONS  
1. Read owner’s manual  
before operating.  
2. Keep unauthorized and untrained  
people away from machine during  
operation.  
4
3. Make sure all safety devices are in  
place before this machine is started.  
6
4. Make sure engine is turned off and  
spark plug wire is disconnected before  
cleaning the machine.  
5. Keep hands and fingers away from  
moving objects.  
5
6. Do not operate machine in an enclosed  
area, proper ventilation is required.  
7. Never leave machine unattended when  
operating.  
8. Always stop engine and allow engine  
to cool before adding fuel or oil.  
P/N 520935  
7
WARNING  
WARNING  
To avoid injury, you MUST read and  
understand operator’s manual before  
using this machine.  
Stand clear of dump handle handle kick-back  
Is possible.  
Keep safety grate, guards and doors  
in place. Shut off engine or electric  
motor before inspection or maintenance.  
3
Wear appropriate dust mask head, hearing and  
Eye protection when operating this equipment.  
Moving parts can cut and crush.  
SHUT OFF engine or electric motor  
before placing hands in mixing drum.  
8
WARNING  
This machine to be operated by qualified  
personnel only. Ask for training as needed.  
To avoid injury, you MUST read and  
understand operator’s manual before  
using this machine.  
Crush hazard area keep hands and fingers  
Clear of safety grate at all times.  
P/N 521229  
Keep safety grate, guards and doors  
in place. Shut off engine or electric  
motor before inspection or maintenance.  
3
Moving parts can cut and crush.  
SHUT OFF engine or electric motor  
before placing hands in mixing drum.  
Moving parts can crush and cut.  
Do not operate with guard removed  
Follow lockout procedure before servicing.  
This machine to be operated by qualified  
personnel only. Ask for training as needed.  
P/N 521229  
P/N 521230  
4
DANGER  
Gasoline is highly flammable.  
DO NOT smoke around or near the equipment.  
Fire or explosion could result from fuel vapors or  
if fuel is spilled on hot engine!  
2
a
P/N 521228  
PUSH  
TO STOP  
1
EM948630  
CAUTION  
DRUM LOCK POSITIONING  
SEE OPERATION MANUAL FOR PROPER  
DRUM LOCK POSITIONING  
LEGEND  
REPRESENTS LOCK PIN  
REPRESENTS DRUM STOP BLOCK  
9
MIX  
TOW  
CIP?????  
CAUTION  
INSPECT BEFORE TOWING  
TIGHTNESS OF WHEEL NUTS  
TIRE PRESSURE  
1. Use manufacturer’s recommended torque values  
when tightening wheel lug nuts.  
11  
2. Use manufacturer’s recommended tire pressure  
values when inflating tires. DO NOT exceed  
recommended tire pressure.  
10  
P/N 521232  
MODEL  
SERIAL  
page 40 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
naMeplate and decals  
no.  
1
2
3
4
5
6
7
parT no. parT name  
EM948630 DECAL, PUSH TO STOP  
QTY. remarks  
1
1
2
1
1
1
521228  
521229  
515275  
504714  
520935  
521230  
DECAL, DO NOT SMOKE  
DECAL, READ MANUAL, CRUSH HAZARD  
DECAL, MQ WHITEMAN LOGO SMALL  
DECAL, MQ WHITEMAN LOGO LARGE  
DECAL, SAFETY INSTRUCTIONS  
DECAL, HANDLE KICK BACK, SAFETY GRATE,  
CRUSH HAZARD  
1
1
1
8
9
10  
504715  
521231  
DECAL, WHITEMAN LOGO LARGE  
DECAL, DRUM LOCK POSITIONING  
NAMEPLATE ................................................................................... 1........CONTACT MQ  
PARTS DEPT.  
11  
521232  
DECAL, INSPECT BEFORE TOWING  
1
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
fraMe assy.  
MOUNT PILLOW BLOCKS  
FOR PINION SHAFT HERE  
MOUNT DRUM  
BEARING HERE  
MOUNT DRUM  
BEARING HERE  
5
6
3
4
9
8
2
7
1
11  
10  
12  
15  
13  
14A  
CHAIN  
&
14  
LINK  
KIT  
A
OPTIONAL TOW BARS  
17  
A
16  
18  
page 42 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
fraMe assy.  
no.  
1
2
3
4
5
6
7
8
parT no.  
514842  
491692  
530023  
507444  
514834  
530013  
20278-001  
EM963692  
492584  
514802  
10176  
parT name  
LOCK, PIN  
COTTER PIN  
SPRING LOCKING PIN  
WASHER, FLAT 3/4"  
MAIN FRAME  
CLUTCH HANDLE LEVER  
CLUTCH HANDLE GRIP  
BOLT 1/2" UNC 1-1/2"  
NUT, LOCK 1/2"  
AXLE, UNIVERSAL  
LOCK NUT 1/2" NC  
BOLT 1/2"-13 X 4 G5  
QTY.  
remarks  
1
1
1
1
1
1
1
6
6
1
1
1
9
10  
11  
12  
13$  
14$  
EM124  
SAFETY CHAIN ................................................1................SOLD ONLY IN KIT  
CONNECTOR LINK  
CLEVIS SAFETY HOOK  
01004  
1
1
14A$ 516580  
15  
16  
17  
18  
13363KIT  
HBC-1  
HLC-1  
CHAIN AND LINK KIT........................................1................INCLUDES ITEMS W/$  
BALL HITCH 2-INCH .........................................1................CONTACT UNIT SALES  
LOOP HITCH.....................................................1................CONTACT UNIT SALES  
PIN HITCH 1-INCH............................................1................CONTACT UNIT SALES  
HPC-1  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
paddle sHaft assy.  
page 44 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
paddle sHaft assy.  
no.  
1
2
parT no.  
514752  
492584  
parT name  
PADDLE SHAFT  
NUT, LOCK 1/2"  
QTY.  
1
6
remarks  
3
4
5
6
7
8
9
10$  
11$  
12$  
13$  
14$  
15$  
16  
17$  
18$  
19  
530140C  
3215  
EM200292  
530141  
6109170  
EM200297  
530143  
PADDLE ARM, CENTER ENGINE END  
SCREW, HHC 1/2-13 X 3-1/2  
INSERT, PADDLE ARM  
PADDLE ARM, ENGINE END  
WASHER, FLAT 1/2"  
U-BOLT, END PADDLES  
PADDLE ARM, CENTER TOW END  
SCREW, 3/8 X 1-1/2 " HHCS  
WASHER, FLAT 3/8"  
BLADE, SIDE, RUBBER  
BLADE, SIDE, SCRAPPER  
NUT, HEX FINISH 3/8--16  
WASHER, LOCK 3/8" MED.  
PADDLE ARM, TOW END  
BLADE ,SCRAPPER END  
BLADE, RUBBER END  
1
2
4
1
6
2
1
18  
28  
4
505196  
3019092  
25667-001  
25668-001  
1456  
4
14  
14  
1
2
2
0166 A  
530142C  
33074-001  
33017-001  
25647-502  
KIT, WIPERS......................................................1................INCLUDES ITEMS W/$  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
steel tub assy.  
24  
23  
22  
20  
20  
20  
26  
29  
21  
25  
20  
28  
27  
14  
30  
15  
31  
4
15  
12  
11  
17  
5
9
1
4
13  
13  
6
3
10  
1
9
16  
6
5
11  
7
8
3
6
8
7
10  
12  
1
2
19  
18  
18  
PART OF  
REAR FRAME  
PART OF  
FRONT FRAME  
NOTES:  
SET SCREWS AND BEARING  
COLLAR ARE INCLUDED WITH  
BEARING AND CANNOT BE  
PURCHASED SEPARATELY.  
1
page 46 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
steel tub assy.  
no.  
1
2
parT no.  
530028  
3249  
parT name  
DRUM BEARING BRACKET  
CAP, DUST  
QTY.  
2
1
remarks  
3
20561-001  
BEARING SEALED............................................2................SET SCREWS AND BEARING  
.............................................................................................COLLAR CANNOT BE SOLD  
.............................................................................................SEPARATELY.  
4
5
6
7
8
9
491008  
CAP, GREASE FITTING  
FITTING, GREASE  
NUT, NYLOCK 3/8"  
WASHER, FLAT 3/8"  
TRUNNION HUB  
ROLL PIN 3/16" X 3/4"  
SEAL, SHAFT (BLACK)  
RING, RETENTION  
SEAL, SHAFT URETHANE (YELLOW)  
BOLT 3/8" NC X 1/4" G5  
DRUM, STEEL  
SET SCREW  
MAIN GEAR  
KEY, 3/8" X 50 MM  
CARRIAGE BOLT 3/8-16 X 1-1/2"  
SHAFT, PADDLE  
WASHER, FLAT 1/2"  
LIFT BAR  
PIN, COTTER  
GRATE  
PIN, COTTER  
HEX NUT 1/2" G5  
WASHER, LOCK 1/2"  
BOLT 1/2" NC 1-1/4" G5  
CAPSCREW, HHCS 1/2" NC X 1-1/4"  
NUT, LOCK1/2" NC  
HANDLE DUMP  
2
2
12  
4
2
2
2
2
2
8
1
2
1
1
4
1
4
1
1
1
2
2
2
2
1
1
1
1
EM916019  
EM969013  
3019092  
514778  
513453  
20654-001  
530029  
20104-002  
513452  
515009  
492484  
530043  
500432  
17985-012  
514752  
6109170  
515032  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
EM925191  
514962  
EM924015  
6109160  
6109180  
EM963692  
492393  
492584  
EM201537  
15081  
GRIP, DUMP HANDLE  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
druM and paddle sHaft cOMplete assy.  
page 48 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
druM and paddle sHaft cOMplete assy.  
no.  
1
parT no.  
516069  
530028  
3249  
20561-001  
491008  
EM916019  
EM969013  
3019092  
514778  
parT name  
DRUM AND SHAFT COMPLETE ASSY............1.......... INCLUDES ITEMS LISTED BELOW  
QTY.  
remarks  
DRUM BEARING BRACKET  
CAP, DUST  
BEARING SEALED  
2
1
2
CAP, GREASE FITTING  
FITTING, GREASE  
NUT, LOCK 3/8"  
WASHER, FLAT 3/8"  
TRUNNION HUB  
2
2
12  
4
2
07594-012  
20654-001  
530029  
ROLL PIN 3/16" X 3/4"  
SEAL, SHAFT (BLACK)  
RING, RETENTION  
2
2
2
20104-002  
513452  
515009  
SEAL, SHAFT URETHANE (YELLOW)  
BOLT 3/8" NC X 1/4" G5  
DRUM, STEEL  
2
8
1
EM961019  
530043  
SET SCREW  
MAIN GEAR  
2
1
10057-034  
EM963057  
514752  
KEY, 3/8" SQ X 2.00 STEEL  
CAPSCREW HHCS 3/8 X 1-1/2"  
SHAFT, PADDLE  
1
4
1
6109170  
514946  
WASHER, FLAT 1/2"  
GRATE  
2
1
EM924015  
6109160  
6109180  
EM963692  
EM201537  
15081  
PIN, COTTER 3/16 X 1  
HEX NUT 1/2-13  
WASHER, LOCK 1/2"  
CAPSCREW, 1/2-13 X 1-1/2 HHCS  
HANDLE DUMP  
GRIP, DUMP HANDLE  
PADDLE SHAFT  
NUT, LOCK 1/2"  
2
2
2
2
1
1
1
6
514752  
492584  
530142  
3043  
EM200292  
530141  
6109170  
EM200297  
530143  
PADDLE ARM, CENTER ENGINE END  
SCREW, HHC 1/2-13 X 6" G5  
INSERT, PADDLE ARM  
PADDLE ARM, ENGINE END  
WASHER, FLAT 1/2"  
U-BOLT, END PADDLES  
PADDLE ARM, CENTER TOW END  
SCREW, 3/8 X 1-1/2 HHCS G5  
WASHER, FLAT 5/16"  
BLADE, SIDE, RUBBER  
BLADE, SIDE, SCRAPPER  
NUT, HEX 5/16" NC G5  
WASHER, LOCK 5/16"  
PADDLE ARM, TOW END  
BLADE ,SCRAPPER END  
BLADE, RUBBER END  
1
2
4
1
6
2
1
18  
28  
4
505196  
EM923023  
25667-001  
25668-001  
2105164  
EM923343  
530140  
4
14  
14  
1
2
2
33074-001  
33017-001  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
axle assy.  
page 50 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
axle assy.  
no.  
1#  
2#  
3
4
5
parT no.  
3469  
29194  
516476  
8164  
EM924008  
EM511159  
EM501299  
EM903113  
EM903012  
EM914288  
EM941306  
514802  
parT name  
DUST CAP  
LUG NUTS  
TIRE AND RIM, TOWMASTER II  
CASTLE NUT 1-20 JAM  
COTTER PIN 1/8" X 1-1/2'  
WASHER, FLAT, .087" THICKNESS  
WASHER, FLAT, .135" THICKNESS  
BEARING CONE  
QTY.  
remarks  
2
8
2
2
2
2
1
4
4
2
6
7
8#  
9#  
10#  
11  
12  
BEARING CUP  
OIL SEAL  
HUB ASSY., 4-BOLT .........................................2................INCLUDES ITEMS W/#  
AXLE, UNIVERSAL  
1
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
enGine assy.  
page 52 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
enGine assy.  
no.  
1
2
3
4
5
6
7
8
parT no.  
EM969013  
3019092  
EM905016  
492378  
JISB2804C25  
513868  
500214  
502226  
492077  
505084  
492467  
491107  
parT name  
NUT NYLOK 3/8" NC G5  
FLAT WASHER 3/8  
PILLOW BLOCK BEARING  
BOLT 3/8" NC X 1-3/4" G5  
RING, RETAINING  
QTY.  
remarks  
4
8
2
4
1
1
1
1
1
1
4
PINION GEAR  
KEY, SQUARE 1/4 X 1/4 X 1-1/2  
PINION SHAFT  
PULLEY (LARGE)  
KEY, 1/4" X 55 MM  
SCREWSET SCREW, 5/16' NC 3/8"  
V-BELT, A-32......................................................2................HONDA GX160, 5.5 HP  
V-BELT, 4L340 ...................................................2................HONDA GX240, 8.0 HP  
BOLT, 3/8" NC X 3" G5  
WASHER, FLAT 5/16"  
9
10  
11  
12  
12  
13  
14  
15  
15  
16  
16  
17  
18  
18  
19  
20  
21  
22  
22  
23  
23  
24  
24  
25  
26  
26  
07055-034  
503117  
508344  
2105162  
492378  
1
1
SET BOLT ENGINE ...........................................4................HONDA GX160, 5.5 HP  
BOLT 3/8 X 1-3/4 HHCS G5 ..............................4................HONDA GX240, 8.0 HP  
GX160UT1HX2 ENGINE, HONDA, 5.5 HP  
GX240UT1HA2 ENGINE, HONDA, 8.0 HP  
514985  
492055  
505205  
604445  
530454  
530019  
EM923023  
3019092  
EM923343  
0166 A  
2105164  
1456  
EM102014  
501019  
90745ZE2600  
1
1
1
BELT RETAINER BAR  
PULLEY, (SMALL) ............................................1................HONDA GX160, 5.5 HP  
PULLEY, (SMALL) ............................................1................HONDA GX240, 8.0 HP  
RETAINING RING  
2
1
1
6
6
4
4
4
4
1
SHAFT, ENGINE MOUNT  
ENGINE MOUNTING PLATE  
WASHER, FLAT 5/16"  
WASHER, FLAT 3/8"  
WASHER, LOCK 5/16"  
WASHER, LOCK 3/8"  
NUT, HEX 5/16"  
NUT, HEX FINISH 3/8-16  
SPRING, EXTENSION  
SQ. KEY 3/16" X 45 MM ...................................1................HONDA GX160, 5.5 HP  
SQ. KEY 6.3 X 6.3 X 43 MM .............................1................HONDA GX240, 8.0 HP  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
electric MOtOr assy.  
page 54 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
electric MOtOr assy.  
no.  
1
2
3
4
parT no.  
EM969013  
3019092  
EM905016  
492378  
20216-001  
20061-001  
500214  
492467  
491112  
503117  
3019092  
492582  
35L229S302  
514985  
502213  
604445  
530454  
530089  
2105164  
492623  
EM923023  
492378  
530024  
parT name  
NUT NYLOK 3/8" G5  
FLAT WASHER 3/8  
PILLOW BLOCK BEARING  
BOLT 3/8 X 1-3/4" G5  
PINION SHAFT  
QTY.  
4
8
2
4
1
1
1
3
2
1
2
1
1
1
1
2
1
1
4
4
8
4
1
1
remarks  
8
9
PULLEY (LARGE)  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
KEY, 1/4 X 1/4 X 1-1/2  
SET SCREW, 5/16' NC 3/8"  
V-BELT, A-40  
CAP SCREW 3/8 NC X 3 G5  
WASHER, FLAT 3/8"  
NUT, NYLON 5/16"-18  
ELECTRIC MOTOR 1.5 HP  
BELT RETAINER BAR  
PULLEY, (SMALL)  
RETAINING RING  
SHAFT, ENGINE MOUNT  
ELECTRIC MOTOR MOUNTING PLATE  
NUT, HEX 5/16" NC  
WASHER, LOCK 5/16"  
WASHER, FLAT 5/16"  
BOLT 3/8" NC X 1-3/4" G5  
SPRING, TENSION  
500169  
KEY, SQUARE 3/16" X 2"  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
cabinet assy.  
2
10  
11  
2
1
12  
2
6
1
4
3
9
8
5
12 OZ.  
RED  
8
SPRAY  
PAINT  
7
13  
NOTES:  
COMPLETE LATCH ASSEMBLY  
INCLUDES ITEMS WITHIN DASHED  
LINES. ITEMS CANNOT BE PURCHASED  
SEPARATELY.  
1
page 56 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
cabinet assy.  
no.  
1
2
3$  
4$  
5$  
6$  
7
8
9
10  
11  
12  
13  
parT no.  
515014  
490202  
13287  
2203  
parT name  
CABINET, ENGINE W/DECALS ........................1................INCLUDES ITEMS W/$  
QTY.  
remarks  
RUBBER PROTECTOR  
LOCK NUT 8-32  
4
6
6
6
2
4
4
4
1
1
1
WASHER, FLAT #10  
SCREW PHP 8-32 X 1/2"  
LATCH ASSY., COMPLETE  
CAP SCREW 3/8" NC X 1-1/4 G8  
WASHER, FLAT 3/8"  
NUT NYLOK 3/8  
KNOB, MUSHROOM  
SWITCH, PUSH-PULL  
WIRE HARNESS  
1307  
491010  
EM963610  
3019092  
EM969013  
29174-001  
29173-001  
504135C  
RAL3020S  
PAINT, SPRAY CAN 12 OZ., RED TRAFFIC AR  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
terMs and cOnditiOns Of sale — parts  
5. Parts must be in new and resalable  
condition, in the original Multiquip  
package (if any), and with Multiquip part  
numbers clearly marked.  
Multiquip reserves the right to quote and  
sell direct to Government agencies, and to  
Original Equipment Manufacturer accounts  
who use our products as integral parts of their  
own products.  
paYmenT Terms  
Terms of payment for parts are net 30 days.  
FreigHT poliCY  
6. The following items are not returnable:  
All parts orders will be shipped collect or  
prepaid with the charges added to the invoice.  
All shipments are F.O.B. point of origin.  
Multiquip’s responsibility ceases when a  
signed manifest has been obtained from the  
carrier, and any claim for shortage or damage  
must be settled between the consignee and  
the carrier.  
a. Obsolete parts. (If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
speCial expediTing serviCe  
A $35.00 surcharge will be added to the  
invoice for special handling including bus  
shipments, insured parcel post or in cases  
where Multiquip must personally deliver the  
parts to the carrier.  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
prior to the return date.  
limiTaTions oF seller’s liaBiliTY  
minimum order  
Multiquip shall not be liable hereunder for  
damages in excess of the purchase price of  
the item with respect to which damages are  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
other special, consequential or incidental  
damages.  
The minimum charge for orders from Multiquip  
is $15.00 net. Customers will be asked for  
instructions regarding handling of orders not  
meeting this requirement.  
c. Any line item with an extended  
dealer net price of less than  
$5.00.  
d. Special order items.  
reTurned goods poliCY  
e. Electrical components.  
f. Paint, chemicals, and lubricants.  
g. Decals and paper products.  
h. Items purchased in kits.  
Return shipments will be accepted and  
credit will be allowed, subject to the following  
provisions:  
limiTaTion oF warranTies  
No warranties, express or implied, are  
made in connection with the sale of parts or  
trade accessories nor as to any engine not  
manufactured by Multiquip. Such warranties  
made in connection with the sale of new,  
complete units are made exclusively by a  
statement of warranty packaged with such  
units, and Multiquip neither assumes nor  
authorizes any person to assume for it  
any other obligation or liability whatever in  
connection with the sale of its products. Apart  
from such written statement of warranty,  
there are no warranties, express, implied or  
statutory, which extend beyond the description  
of the products on the face hereof.  
1. A Returned Material Authorization  
must be approved by Multiquip prior to  
shipment.  
7. The sender will be notified of any material  
received that is not acceptable.  
8. Such material will be held for five  
working days from notification, pending  
instructions. If a reply is not received  
within five days, the material will be  
returned to the sender at his expense.  
2. To obtain a Return Material Authorization,  
a list must be provided to Multiquip  
Parts Sales that defines item numbers,  
quantities, and descriptions of the items  
to be returned.  
9. Credit on returned parts will be issued  
at dealer net price at time of the original  
purchase, less a 15% restocking  
charge.  
a. The parts numbers and descriptions  
must match the current parts price  
list.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
based on the list price that was effective  
twelve months prior to the RMA date.  
c. The list must state the reason(s)  
for the return.  
Effective: February 22, 2006  
d. The list must reference the sales  
order(s) or invoice(s) under  
which the items were originally  
purchased.  
11. Credit issued will be applied to future  
purchases only.  
priCing and reBaTes  
e. The list must include the name  
and phone number of the person  
requesting the RMA.  
Prices are subject to change without prior  
notice. Price changes are effective on a  
specific date and all orders received on or  
after that date will be billed at the revised price.  
Rebates for price declines and added charges  
for price increases will not be made for stock  
on hand at the time of any price change.  
3. AcopyoftheReturnMaterialAuthorization  
must accompany the return shipment.  
4. Freight is at the sender’s expense. All  
parts must be returned freight prepaid to  
Multiquip’s designated receiving point.  
page 58 — wm63-series mixer • operaTion and parTs manual — rev. #0 (09/27/12)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
nOtes  
wm63-series mixer • operaTion and parTs manual — rev. #0 (069/27/12) — page 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OperatiOn and parts Manual  
HERE’S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
United StateS  
Multiquip Corporate Office  
MQ Parts Department  
18910 Wilmington Ave.  
Carson, CA 90746  
Contact: [email protected]  
Tel. (800) 421-1244  
Fax (310) 537-3927  
800-427-1244  
310-537-3700  
Fax: 800-672-7877  
Fax: 310-637-3284  
Service Department  
Warranty Department  
800-421-1244  
310-537-3700  
Fax: 310-537-4259  
Fax: 310-943-2238  
800-421-1244  
310-537-3700  
Fax: 310-943-2249  
Technical Assistance  
800-478-1244  
mexico  
United Kingdom  
MQ Cipsa  
Multiquip (UK) Limited Head Office  
Carr. Fed. Mexico-Puebla KM 126.5  
Momoxpan, Cholula, Puebla 72760 Mexico  
Contact: [email protected]  
Tel: (52) 222-225-9900  
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223  
Fax: (52) 222-285-0420 Globe Lane,  
Dukinfield, Cheshire SK16 4UJ  
Contact: [email protected]  
Fax: 0161 339 3226  
Canada  
Multiquip  
4110 Industriel Boul.  
Laval, Quebec, Canada H7L 6V3  
Contact: [email protected]  
Tel: (450) 625-2244  
Tel: (877) 963-4411  
Fax: (450) 625-8664  
© COPYRIGHT 2012, MULTIQUIP INC.  
Multiquip Inc, the MQ logo and the Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other  
trademarks are the property of their respective owners and used with permission.  
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in  
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published  
in this publication at any time without notice and without incurring any obligations.  
Your Local Dealer is:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Clothes Dryer T234 C User Manual
Milwaukee Saw 6390 User Manual
MotoSAT Satellite TV System Executive User Manual
NETGEAR Network Router 202 11171 04 User Manual
Nextar Digital Photo Frame N1 519 User Manual
Omega Engineering Water Pump FPUHP User Manual
Oregon Scientific Clock RM383PA User Manual
OTC Wireless Network Card WiSER2400 User Manual
Panasonic Computer Monitor BT 4LH310 User Manual
Panasonic Telephone KX T7130 User Manual