PARTS AND OPERATION MANUAL
MIX N' GO
MINI CONCRETE MIXER
STEEL DRUM MODELS
MC3SE, MC3H (HONDA)
Revision #0 (09/09/02)
MULTIQUIPINC.
18910 WILMINGTON AVE.
PARTS DEPARTMENT:
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
E-mail:mq@multiquip.com • www:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #0 (08/09/02) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Honda G100K2QA2 Engine
Air Cleaner Assy................................................. 38-39
Camshaft Assy. .................................................. 40-41
Carburetor Assy. ................................................ 42-42
Control Assy. ...................................................... 43-44
Crankcase Cover Assy. ...................................... 45-46
Crankshaft Assy. ................................................ 47-48
Cylinder Barrel Assy. .......................................... 49-50
Fan Cover Assy. ................................................. 51-52
Flywheel Assy..................................................... 53-54
Fuel Tank Assy. .................................................. 55-56
Gasket Kit Assy. ................................................. 57-58
Ignition Coil Assy. ............................................... 60-61
Muffler Assy........................................................ 62-63
Piston Assy. ........................................................ 64-65
Recoil Starter Assy............................................. 66-67
Labels Assy. ....................................................... 68-69
Multiquip Mix N' Go — Mini
ConcreteMixer
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation .................................... 8-10
Operation and Safety Decals ............................. 11-12
Specifications .......................................................... 13
Dimensions (Mixer) ................................................. 14
Dimensions (Electric Motor).................................... 15
General Information ................................................ 16
Mixer Components.................................................. 17
Basic Engine ........................................................... 18
Assembly Instructions ........................................ 19-20
Pre-Inspection (Gasoline Engine) ........................... 21
Initial Start-up (Electric Motor) ................................ 22
Initial Start-up (Gasoline Engine)....................... 23-24
Maintenance ...................................................... 25-27
Preparation for Long-Term Storage........................ 28
Troubleshooting (Engine)........................................ 30
Troubleshooting (Engine/Mixer) .............................. 31
Explanation Of Code In Remarks Column .............. 32
Suggested Spare Parts ........................................... 33
Nameplate and Decals....................................... 34-35
Mixer Assy. ......................................................... 36-37
Terms and Conditions of Sale ................................. 70
Specification and part number
are subject to change without
notice.
PAGE 4 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
■ Dealer account number
■ Dealer name and address
■ Shipping address (if different than billing address)
■ Return fax number
■ Applicable model number
■ Quantity, part number and description of each part
■ Specify preferred method of shipment:
UPS Ground
•
UPS Second Day or Third Day*
•
UPS Next Day*
•
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
Airborne Express*
•
Truck or parcel post
•
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
Additional Discount
1-9 items
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
Now! Direct TOLL-FREE access
to our Parts Department!
■
UPS Ground Service at no charge for freight
■
UPS Third Day Service at one-half of actual freight
Toll-free nationwide:
800-421-1244
cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
Toll-free FAX:
*DISCOUNTS ARE SUBJECT TO CHANGE*
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
This Owner's Manual has been
developed to provide complete
instructions for the safe and
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
efficient operation of the Multiquip
MIX N' GO MIXER Models
MC3E, MC3B and MC3H. Refer
to the engine manufacturers
instructions for data relative to its
safe operation.
Before using this mixer, ensure
that the operating individual
has read and understands all
instructions in this manual.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with the MIX N' GO MIXER
operation will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 6 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine or electric motor
ON/OFF switch in the OFF position when the
mixer is not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your mixer, other property, or the
surrounding environment.
ALWAYS wear approved eye and hearing
protection.
This mixer, other property, or the
surrounding environment could
be damaged if you do not follow
instructions.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
NEVERtouchthehotexhaustmanifold,
muffler or cylinder.Allow these parts to
cool before servicing engine or mixer.
DANGER:
Failure to follow instructions in this manual may
lead to serious injury or even death! This
equipment is to be operated by trained and
qualified personnel only!This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the Mix N' Go Mixer:
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
GENERAL SAFETY
■
DO NOT operate or service this equipment before
readingthisentiremanual.
The engine of this mixer requires an adequate free flow of
cooling air. NEVER! operate the roller mixer in any enclosed
or narrow area where free flow of the air is restricted. If the air
flow is restricted it will cause
■
■
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job.
serious damage to the
mixer or engine and may
cause injury to people and
property. Remember the
mixer's engine (gasoline
models only) gives off
DEADLY gases.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
NEVER operate this equipment under the
influence or drugs or alcohol.
and open flames.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
NEVER operate the mixer in an explosive
atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
ALWAYS check the machine for loosened threads or bolts
before starting.
ALWAYS wear proper respiratory (mask) hearing and eye
protection equipment when operating the mixer.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
■
■
High Temperatures – Always stop engine and allow the
engine to cool before adding fuel, oil or performing service
and maintenance functions. Contact with hot components can
cause serious burns.
damage may occur.
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using roller.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
■
■
If mixer is equipped with an electric motor, operate only at
120VAC, 60 Hz.
■
■
■
■
NEVER leave the mixer unattended, turn off engine or electric
motor when unattended.
Make sure the OFF/ON power switch is always in the OFF
position before inserting the mixer's power plug into an AC
receptacle (electric model only).
CAUTION must always be observed while servicing this mixer.
Rotating parts can cause injury if contacted.
Unauthorized equipment modifications will void all
warranties.
Maintenance Safety
■
NEVER lubricate components or attempt service on a running
machine.
Ensure that any trailing cable is protected against damage
and not liable to be tripped over or trapped underneath the
mixer.
■
ALWAYS allow the machine a proper amount of time to cool
before servicing.
■
■
Ensure any extention cables must be no longer than 30 meters
(100 feet) in length and that the wire section is 2.5 mm 2.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
DO NOT allow extension cord to come into contact with water
or fluids.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
DO NOT expose power tools to rain or wet conditions.
This mixer is intended for the production of concrete, mortar
and plaster. Mixer must be used only for its intended purpose.
DO NOT use food or plastic containers to dispose of
hazardous waste.
■
This mixer is not suitable for the mixing of flammable or
explosive substances.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■
■
NEVER operate the mixer in an explosive atmosphere.
Before starting the mixer, check that all guards are in position
and correctly fitted.
■
■
DO NOT tip mixer onto drum mouth when the motor is running.
Keep area around the mixer clear of obstructions which
could cause persons to fall onto moving parts.
■
■
ALWAYS ensure mixer is on level ground before mixing.
Become familiar with the controls of the machine before
operating.
■
■
ALWAYS replace any worn or damaged warning decals.
Ensure the drum is rotating while filling and emptying the
drum.
■
■
DO NOT use mixer as a wheel barrel.
ALWAYS disconnect AC power plug from power source
before moving mixer (electric model only).
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Emergencies
■
ALWAYS know the location of the nearest fire extinguisher.
■
■
ALWAYS know the location of the nearest first aid kit.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
PAGE 10 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
Machine Safety Decals
The Mix N' Go mixer is equipped with a number of safety decals.These decals are provided for operator safety and maintenance
information.The illustration below and on the next page shows these decals as they appear on the machine.Should any of these
decals become unreadable, replacements can be obtained from your dealer.
WARNING!
ALARMA!
AVERTISSEMENT!
ENGLISH - WARNING! TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL
ESPAÑOL - ATENCION! PARA REDUCIR EL RIESGO DEL LESIONES EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DE INSTRUCCIONES
FRANÇAIS - ATTENTION! AFIN DE DIMINUER LE RISQUE DE BLESSURES L’UTILISATEUR DOIT LIRE ET COMPRENDRE CE MANUEL D’ INSTRUCTIONS
DCL251
P/N DCL251
TBD
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND SAFETY DECALS
WARNING!
1. Read owner’s manual before operating mixer.
ADVERTENCIA!
1. Lea el manual de operació antes de usar la mezcladora.
AVERTISSEMENT!
1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur.
2. Keep unauthorized and untrained people away
from mixer during operation.
3. Make sure all safety devices (guards) are in place
before mixer is started.
2. Mantenga personas que no estén autorizadas o capacitadas
alejades de la mezcladora durante el funcionamiento de la
máquina.
2. Seul un personnel qualifié peut être authorisé à se trouver à proximité
du malaxeur quand il est en opération.
3. Assurez vous que tous les dispositifs de sécurité sont en place avant
de mettre le malaxeur en marche.
3. Asegúreseque todos los aparatos de seguridad estén
trabajando apropiadamente antes de usar la mezcladora.
4. Keep hands and fingers away from moving objects.
4. Gardez les mains et doigts loin de toute piè en mouvement.
4. Mantenga las monos y dedos alejados de objetos en moviminto.
5. NEVER leave mixer unattended when operating.
6. ALWAYS check V-belt before starting mixer.
5. NE LAISSEZ jamais le malaxeur sans surveillance quand il est en
opération.
5. NUNCA se aleje de la mezclaora mientras ésta, este trabajando!
6. SIEMPRE inspeccione la banda antes de encender la mezcladora. 6. VEUILLEZ toujours vérifier la courroie avant de mettre le malaxeur
en marche.
GASOLINE ENGINE
Make sure engine is turned off and spark plug wire is
disconnected before cleaning mixer.
MOTEUR À ESSENCE
Assurez vous que le moteur est arrêté et que le fil de la bougie est
débranché avant de nettoyer le malaxeur.
MÁQUINAS DE GASOLINA
Asegure que la máquina este apagada y el alambre de la bujía
este desconectado antes de empezar a limpiar la mezcladora.
N’ UTILISEZ pas le malaxeur dans un endroit fermé, il est nécessaire
de travailler dans un endroit avec une bonne aération.
DO NOT operate mixer in an enclosed area, proper
ventilation is required.
NO encienda la mezcladora en una área cerrada; es necesario
estar en una área que tenga apropiada ventilación.
VEUILLEZ toujours vé la courroie avant de mettre le malaxeur en
marche.
ALWAYS stop the engine and allow engine to cool before
adding fuel or oil.
SIEMPRE apague la máquina y permita que se enfrie antes de
ponerle gasolina o aceite.
VÉRIFIEZ toujours le niveau d’essence et d’huile ainsi que le filtre à
air avant de mettre le moteur en marche.
ALWAYS check fuel, oil and air filter before starting engine.
SIEMPRE revise la gasolina, aceite, y el filtro del air antes de
encender la máquina.
ELECTRIC MOTOR
Make sure power cord has been disconnected from power
source before cleaning mixer.
MOTOR ELÉCTRICO
Asegúrese que el cable de corriente esté de empezar a limpiar
la mezcladora.
MOTEUR ÉLECTRIQUE
Assures vous toujours que le cable a été débranché de la prise de
courant avant de nettoyer le malaxeur.
Este motor elétrico está solamente capacitado para corriente
alterna de 115 voltios.
This electric motor is for 115 VAC operation only.
Ce moteur électrique à été conçu pour opération à 115 volts seulement.
ALWAYS use an extension cord of proper size, see chart
below:
SIEMPRE use el tamaño de extensiones de alambre indicado
como muestra el diagrama abajo:
Il faut toujours utiliser une rallonge de taille appropriée, veuillez s’il vous
référer au diagramme suivant:
TAMAÑO DE EXTENSIÓN
TAILLE DE LA RALLONGE
EXTENSION CORD SIZE
Alambre
Alambre
Numéro 6
Cable
Cable
Cable
Cable
Numéro 6
Alambre
Numéro 12
Alambre
No. 12 Wire
No. 10 Wire
No. 6 Wire
200 feet
No. 8 Wire
Numéro 10
Numéro 12
Numéro 10
Numéro 8
Numéro 8
75 feet
50 feet
100 feet
200 pies
75 pies
100 pies
50 pieds
50 pieds
50 pies
50 pieds
50 pieds
(22.86 meters)
(15.24 meters)
(30.48 meters) (60.96 meters)
(22.86 metros) (30.48 metros) (60.96 metros)
(15.24 métres)
(15.24 métres)
(15.24 métres) (15.24 métres)
(15.24 metros)
REMOVE BOLT AND FILL
WITH EP. 90 GEAR OIL
NEVER! OPERATE MIXER WITH
V-BELT COVER REMOVED.
ELECTRIC
MOTOR
REMOVER EL TORÑILLO Y
LLENAR CON ACEITE DE
ENGRNAJE EP. 90
NUNCA! MANEJE LA MEZCLADORA
SIN LA COBERTURA DE BANDA-V
REMOVIDA.
MOTOR
ELÉCTRICO
ELECTRIC
MOTOR
MOTEUR
ÉLECTRIQUE
ÔTEZ LE BOULON ET
REMPLISSEZ AVEC DE I’HUILE
EP. 90 À ENGRENAGES
N’ UTILISEZ! JAMAIS LE MALAXEUR
SANS LE COUVERCLE DE LA COURROIE.
MOTOR
ELÉCTRICO
MOTEUR
ÉLECTRIQUE
CHECK DAILY
REVISAR DIARIO
VÉRIFIEZ QUOTIDIENNEMENT
DCL250
P/N DCL250
PAGE 12 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — SPECIFICATIONS
Table 1. Specifications (Engine & Electric Motor)
Model
HONDA G100K2QA2
BALDOR 17LYE304
3/4 HP, 120 VAC, Single
Phase Electric Motor
Type
4-stroke, Side valve, Single Cylinder
20.5 in. X 18.1 in.
(52 mm x 46 mm)
Bore X Stroke
N/A
Displacement
6.0 cu. in. (98 cc)
2.5 H.P. at 3,600 R.P.M.
1,400 100 R.P.M.
N/A
3/4 H.P./3,450 RPM
N/A
Max Output
Engine/Electric Motor
Standard Idle Speed
Approx. 0.37 U.S. Gallons
(1.4 Liters)
Fuel Tank Capacity
N/A
Fuel
Unleaded Gasoline
0.48 U.S. Quarts (0.45 Liters)
Centrifugal Fly-weight Type
Recoil Start
N/A
N/A
N/A
N/A
Lube Oil Capacity
Speed Control Method
Starting Method
10.8 x 10.6 X 13.6 in.
(275 X 270 X 345 mm)
11.75 x 6.0 X 8.0 in.
(298 X 152 X 203 mm)
Dimensions (L x W x H)
Dry Net Weight
19.2 lbs (8.7 Kg.)
Approx. 12 lbs. (5.4 Kg.)
Table 2. Mix N' Go Mixer Specifications
34 in. (863.6 mm)
Height
Width
23-5/8 in. (584.2 mm)
Length
48-1/2 in. (1,219.2 mm)
Stand Weight
35 lbs. (15.9 Kg)
Maximum Drum Capacity
4.5 cu. ft. (0.13 m3)
3.0 cu. ft. (0.08 m3)
129 lbs. (58.5 Kg)
138 lbs. (62.6 Kg)
Maximum Mixing Capacity (1/2 bag)
Unladen Weight - Electric Motor
Unladen Weight - Gasoline Engine
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — DIMENSIONS (MIXER)
PAGE 14 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR)
Figure 2. Electric Motor
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — GENERAL INFORMATION
PORTABLE GENERATORS
APPLICATION
This mixer is only intended for the production of concrete,
mortar and plaster. The mixer must be used for its intended
purposes and is not suitable for the mixing of flammable or
explosive substances. The mixer must not be used in an
explosive atmosphere.
When using a portable generator it must have a minimum
output of 2.5 kw and be continuous rated.
GEARBOX
The gearbox oil level has been preset at the factory prior to
shipping. Before inspecting the gearbox oil level (Figures 30
and 31), make sure the gearbox is cold before removing the
filler plug. Fill up with EP90. or similar gear oil.
POWER PLANTS
This portable mixer is powered by either a Honda G100K2,
4-stroke, side valve, single cylinder, gasoline engine rated
at 2.5 hp @3,600 rpm. or a 0.75 hp electric motor.
TRANSPORTINGTHE MIXER
Use a ramp (Figure 3) to load and unload the mixer from the
transport vehicle. Never drop the mixer onto the ground; damage
to the mixer could result.
DRUM ASSEMBLY
The drum is instantly removable by unscrewing counter-
clockwise. When inserting drum onto gearbox shaft, make sure
that drum is fully screwed onto shoulder or threads may be
damaged. Use extreme care when screwing on the drum,
spinning drum onto the gearbox shaft too fast may damage
gearbox.
ELECTRICAL
If mixer is equipped with an electric motor, make sure that
the power being supplied to the motor corresponds to the
voltage rating label on the motor.Supplying the wrong voltage
to the electric motor will cause severe electrical damage to
the motor.
Always make sure that OFF/ON switch on the electric motor
is in the OFF position before applying power.
It is strongly recommended that when plugging in the
mixer's power cord into a receptacle, that a G.F.C.I.(Ground
Fault Current Interrupter) receptacle be used.
EXTENSION CABLES
The extension cable should be a 3-wire configuration that
includes a ground wire that conforms to UL code. The wire
cross section must be a minimum of 2.5 mm2 . Choose an
extension cord of adequate current carrying as Reference in
Table 5. Remember distance affects the wire size of the
extension cable.
Ensure that the extension cable is carefully laid out avoid-
ing wet areas, sharp edges and locations where vehicles
might run over it. Avoid allowing the extension cable to be
trapped underneath the mixer.
Unroll the extension cable fully or it will overheat and could
catch fire. Make sure that all extension cable connections
are dry and safe. Replace any defective or badly worn ex-
tension cable immediately.
Figure 3. Mixer Loading
PAGE 16 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MIXER COMPONENTS
Figure 4 shows the basic components of the Mix N' Go
Mixer.
Figure 4. Mixer Components
Table 3. MIXING HINTS
BATCH QUANTITIES
APPROX. BATCH
OUTPUT
MIX
RATIOS
CEMENT 112 lbs.
SAND
CU. FT.
STONE
CU. FT.
APPLICATIONS
(50 Kgs.)
Bag
LTR
35
LTR
71
CU. FT.
3
LTR
85
1:2:4
1:3:6
1:4:8
1/2 BAG
1/3 BAG
1/4 BAG
1-1/4
1-1/4
1-1/4
2-1/2
2-1/2
2-1/2
Most Ordinary
Foundations
35
71
2-3/4
2-3/4
78
35
71
78
Rough Mass
Concrete
1:1-1/2:3
2/3 BAG
1-1/4
35
3
71
3
85
Watertight Floors,
Tanks, Pits, Etc.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — BASIC ENGINE
Figure 5. Engine Controls and Components
INITIAL SERVICING
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
The engine (Figure 5) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions and details of operation and servicing.The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
8. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an air
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT
9. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch) Clean
spark plug once a week.
attempt to start the engine until the fuel residue has been completely
wiped up, and the area surrounding the engine is dry.
10. Muffler – Used to reduce noise and emissions.
2. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
starting, OFF position stops engine operation.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
5. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
11. Oil Drain Plug – Remove this plug to remove oil from the
engine's crankcase.
12. Dipstick/Oil Filler Cap – Remove this cap to determine if
the engine oil is low. Add oil through this filler port as
recommended in Table 4.
FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
PAGE 18 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS
Assembly
1. Removethemixerdrum andassociatedcomponentsfrom
the packing container (Figure 6). Match the components
againstthepartslisttomakesurethattheyareallaccounted
for.
Figure 6. Packing Container
Figure 8. Mixing Drum Placement
2. Placethemixerframeonasecurelevelsurface,andattach
the top cover as shown in Figure 7.
4. Placethetwohalvesofthesupportstandtogether(Figure9).
The left support stand fits into the center boss on the right
supportstand.
5. InserttheadapterpinthroughbossesasshowninFigure9.
Oncetheadapterpinhasbeeninsertedandaligned, insert
the locking pin. Place the round part of the locking pin over
the bottom section of the adapter pin.
Figure 7.Top Cover Placement
3. Fit the mixing drum onto gearbox shaft as shown in Figure
8.Rotatedruminaclockwisedirection,makesurethedrum
fits right up to the shoulder on the gearbox shaft.
CAUTION
Figure 9. Support Stand
DO NOT spin the drum on fast, as this may
damage the gearbox.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS
6. Tip mixer onto mouth as shown in Figure 10, and insert
support stand into frame swivel point.
9. Before attempting to lift mixer, locate the frame locking clip.
AttachthelockingclipasshowninFigure12.Thiswillprevent
the mixing drum from moving when the mixer is positioned
in an upright position.
Figure 12. Frame Locking Clip
10. DO NOT tilt the mixer on a wet, smooth or slippery surface.
Figure 10. Attaching Support Stand
7. Removebothwheelsandwheelretainersfromthepacking
container.
8. Placeonewheeloneachsideof themixer'saxleasshown
in Figure 11. Position wheel retainer over axle to secure
wheel in place. Use a rubber mallet when striking wheel
retainer.
Figure 13. Slippery or Wet Surfaces
11. Oncethestandhasbeenassembled,andthelockingcliphas
been secured, begin tilting the mixer to an upright position.
Remember always tilt from the front of the mixer as shown
in Figure 14.
Figure 11.Wheels and Wheel Retainers
Figure 14.Tilting Mixer to Upright Position
PAGE 20 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE)
3. Insertandremovethedipstickwithoutscrewingitintothefiller
neck. Check the oil level shown on the dipstick.
CAUTION
NEVER operate the mixer in
a confined area or enclosed
area structure that does not
provide ample free flow of air.
4. Iftheoillevelislow(Figure16), filltotheedgeoftheoilfiller
holewiththerecommendedoiltype(Table4).Maximum oil
capacity is 0.48 quarts (.45 liters)
ALWAYS wear approved eye and hearing
protection before operating the mixer.
NEVER place hands inside drum while the
engine is running.ALWAYS shut the engine
down before performing any kind of
maintenance service on the mixer.
Figure 16. Engine Oil Dipstick (Oil Level)
Table 4. Oil Type
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
Before Starting
1.
2.
Read safety instructions at the beginning of manual.
Clean the mixer, removing dirt and dust, particularly the
engine cooling air inlet, carburetor and air cleaner.
0°C or Lower
3.
4.
5.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
Explosive Fuel
Check fastening nuts and bolts for tightness.
Fuel Check
Engine Oil Check
Motor fuels are highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the mixer if the engine is hot! or running.
1.
To check the engine oil level, place the mixer on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 15) and wipe clean.
1. Remove the gasoline cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
V-Belt Check
A worn or damagedV-belt can adversely affect the performance
of the trowel.If aV-belt is defective or worn simply replace theV-
belt as outlined in the maintenance section of this manual.
Figure 15. Engine Oil Dipstick (Removal)
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — INITIAL START-UP (ELECTRIC MOTOR)
5. Plug the other end of the extension cord into a 120 VAC
G.F.C.I.protected receptacle. Rememberthepowerrequire-
ments for this electric motor is 120VAC, 60 Hz. The use of
any other input voltage will severely damage the motor.
Initial Start-up Instructions (Electric Motor)
Starting
CAUTION:
DO NOT attempt to operate the mixer until
the Safety, General Information and
Inspection sections have been read and
understood.
WARNING:
ALWAYS read the label on the electric motor
before applying power.The label will indicate the
proper power requirements for the motor.
Remember the use of any other input voltage will
severely damage the motor.
1. Before starting, make sure mixer is positioned on a secure
flatsurfacetopreventtipping.
2. Use an extension cord (see Table 5) of adequate current
carryingcapacity,insert theelectricmotor'spowerplug into
one end of the extension cord.
WARNING:
To prevent tripping (Figure 18) of both the mixer
and personnel, position the extension cord so that
it lays flat and is not curled underneath the mixer.
3. NEVER! use a worn or frayed extension cord.
4. NEVER! operate mixer withV-belt cover removed.
Table 5. Extension Cord Size
No. 12 Wire
No. 10 Wire
No. 8 Wire
No. 6 Wire
50 (feet)
75 (feet)
100 (feet)
200 (feet)
(15.24 meters) (22.86 meters (30.48 meters (60.96 meters
Figure 18. Mixer (Tripping)
DANGER
6. Thedrumshouldberotatingallowing themixingprocess to
begin. Use a shovel (Figure 19) to place the cement mix
inside the drum, add water as required. Be careful to only
placethetipoftheshovelinsidethedrum.Placingtheshovel
allthewayinsidethedrumwillcausetheshoveltostrikethe
blades. Thisconditionwillmaketheshovelrotate,andcould
cause injury to personnel.
NEVER! touch the power cord (Figure 17)
with wet hands or while standing in water
when it is connected to a power source.The
possibly exists of electrical shock
(electrocution) even death. NEVER! spray
water directly on the electric motor.
WET
HANDS
POWER
CORD
(POWER ON)
Figure 19. Mixing Drum (Placing cement Mix))
6. SeeTable3formixinghints.NEVER!placehandsinsidethe
Figure 17. Extension Cord (Wet Hands)
drum while the drum is rotating.
PAGE 22 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE)
3. Place the choke lever (Figure 22) in the "OPEN " position
DO NOT attempt to operate the mixer until
the Safety, General Information and
Inspection sections of this manual have
been read and thoroughly understood.
if starting a cold engine.
This section is intended to assist the operator with the initial
start-up of the walk-behind trowel. It is extremely important that
this section be read carefully before attempting to use the trowel
in the field.
Starting the Engine (HONDA engine)
1. Place the engine fuel valve lever (Figure 20) to the "ON"
position.
Figure 22. Engine Choke Lever (Open)
4. Placethechokelever(Figure23)inthe"CLOSED"position
if starting a warm engine or the temperature is warm.
Figure 20. Engine Fuel Valve Lever (ON Position)
2. Place the trowel's throttle lever (Figure 21) to the "IDLE"
position.
Figure 23. Engine Choke Lever (Closed)
5. Place the engine ON/OFF switch (Figure 24) in the "ON "
position.
Figure 21. Throttle Lever (Idle Position)
Figure 24. Engine ON/OFF Switch (ON Position)
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE)
6. Grasp the starter grip (Figure 25) and slowly pull it out.The
2. Aftertheenginecools,turntheengineON/OFFswitchtothe
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
“OFF” position (Figure 28 ).
Figure 25. Starter Grip
Figure 28. Engine ON/OFF Switch (OFF Position)
7. If the engine has started, slowly return the choke lever
(Figure 23 ) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
3. Closethefuelshut-offvalve (Figure29)bymovingthefuel
valve lever to the OFF position.
8. Beforethemixerisplacedintooperation,runtheenginefor
severalminutes. Checkforfuelleaks,andnoisesthatwould
associate with a loseV-belt cover or component.
9. To begin mixing, place the throttle lever (Figure 26) in the
"RUN" position
Figure 29. FuelValve Lever (OFF Position)
Emergency Showdown
1. MovethethrottleleverquicklytotheIDLE position,andturn
the engine ON/OFF switch to the OFF position.
Figure 26. Throttle Lever (Run Position)
Stopping The Engine
Normal Shutdown
1. Movethethrottlelever tothe IDLEposition (Figure27)and
run the engine for three minutes at low speed.
Figure 27. Throttle Lever (Idle Position)
PAGE 24 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MAINTENANCE
Maintenance
5. Insert oil filler plug and tighten.
Gearbox Oil Check
1. Positionthe mixeronalevel surface and place asupport block
under thefrontofthemixer frameas showninFigure30.This
will level the mixer.
2. NEVER! check the gearbox oil level with the mixer tilted up or
down.ALWAYS check the gearbox oil level with the mixer in a
level position.
Figure 31. Gearbox Oil Level Check
V-Belt Check
1. To adjustV-belts, removeV-belt cover and loosen the main
motor mount bolts, raise electric motor and retighten bolts.
Belttensionshouldbeadjustedsothatthemaximumdeflec-
tion is approximately 3/8 inch (10 mm).
2. ReplaceV-beltcover.
Figure 30. Mixer Positioning (Gearbox Oil Level)
CAUTION :
Gerarbox Removal
Check the gearbox oil level monthly
before operating mixer. Low oil level or no
oil will severely damage gearbox.
1. Remove drum by turning counter-clockwise to release from
gearboxshaft.
2. Remove pulley, remember the nut securing the pulley is left-
handthreaded. Removecirclip,anddrawoutshaft.
3. Beforeinspectingthegearboxoillevel,makesurethegearbox
iscoldbeforeremovingthefillerplug.Hot!oilcanburnskinand
cause injury.Let oil cool before checking.
3. Remove the 5 bolts securing rear plate.
4. Removegearboxoilfillerplug (Figure31)andfillwithEP90or
similargearoiltothelevelofthefillerplug.Replacegearboxoil
every 3,000 hours. Gerabox oil capacity is 8-10 ounces.
4. Reassembleinreverseorder,takingcaretoensuregearteeth
aremeshedcorrectly.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE)
Table 6. Engine Maintenance Schedule
FIRST
EVERY
EVERY
EVERY
YEAR
OR
EVERY
2 YEARS
OR
MONTH 3 MONTHS 6 MONTHS
OR
DESCRIPTION (3)
OPERATION
BEFORE
OR
OR
10 HRS.
25 HRS.
50 HRS.
100 HRS.
200 HRS.
CHECK
CHANGE
CHECK
X
Engine Oil
X
X
X
Air Cleaner
All Nuts & Bolts
Spark Plug
CHANGE
X (1)
Re-tighten If
Necessary
CHECK-CLEAN
REPLACE
CHECK
X
X
X
Cooling Fins
Spark Arrester
Fuel Tank
CLEAN
X
X
CLEAN
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
CHECK-ADJUST
CHECK
X (2)
Valve Clearance
Fuel lines
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA shop Manual for service procedures
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
Reference manufacturer engine
manual for specific servicing
instructions.
PAGE 26 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE)
DANGER :
Maintenance
Perform the scheduled maintenance procedures as definded by
Table 6 and below:
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
DAILY
■
Thoroughly remove dirt and oil from the engine and control
area.Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
gearbox for oil leaks. Repair or replace as needed.
ENGINEAIRCLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 34.
WEEKLY
2. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
■
Remove the fuel filter cap and clean the inside of the fuel
tank.
■
■
Remove or clean the filter at the bottom of the tank.
Remove and clean the spark plug (Figure 32), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit
has electronic ignition, which requires no adjustments.
Figure 32. Spark Plug Gap
ENGINEOIL
1. Drain the engine oil when the oil is warm as shown in
Figure 33.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
Figure 34. Engine Air Cleaner
3. Replace engine oil with recommended type oil as listed
in Table 4. Engine oil capacity is .48 quarts (0.45 liters).
DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securly.
Figure 33. Engine Oil (Draining)
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE
Mixer Storage
For storage of the mixer for over 30 days, the following is
recommended:
z
Drain the fuel tank completely, or add STA-BIL to the
fuel.
z
z
Run the engine until the fuel is completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
z
z
Clean the entire mixer and engine compartment.
Cover the mixer and place it a clean dry area, that is
protected from harsh elements.
PAGE 28 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start
POSSIBLE PROBLEM
SOLUTION
Ignition plug being bridge?
Carbon deposit at ignition?
Check ignition system.
Clean or replace ignition.
Replace insulators.
Fuel is available but spark plug
will not ignite. (Power available
at high tension cable).
Short circuit due to defective
insulators?
Improper spark gap?
Set spark plug gap to the correct gap.
Check stop switch circuit. Replace stop switch if defective.
Replace ignition coil.
Short circuit at stop switch?
Ignition coil defective?
Fuel is available but spark plug
will not ignite. (Power NOT
available at high tension cable).
Muffler clogged with carbon
deposits?
Clean or replace muffler.
Fuel is available and spark plug
ignites (compression normal).
Fuel in use inadequate (water,
dust)?
Flush fuel sytem and replace with fresh fuel.
Air Cleaner clogged?
Defective cylinder head gasket?
Cylinder worn?
Clean or replace air cleaner.
Tighten cylinder head bolts or replace head gasket.
Replace cylinder.
Fuel is available and spark plug
ignites (compression low ).
Spark plug loose?
Tighen spark plug.
Operation not satisfactory
Air cleaner clogged?
Air in fuel line?
Bleed (remove air) from fuel line.
Adjust carbureator float
Not enough power available
(compression normal, no miss-
firing).
Fuel level in carbureator float
chamber improper?
Carbon deposits in cylinder?
Ignition coil defective?
Clean or replace cylinder
Flush fuel sytem and replace with fresh fuel.
Replace ignition wires, clean ignition.
Flush fuel sytem and replace with fresh fuel.
Not enough power available
(compression normal, miss-
firing).
Ignition plug often shorts?
Fuel in use inadequate (water,
dust)?
Excessive carbon depostion in
combustion chamber?
Clean or replace crankcase.
Clean or replace muffler.
Engine overheats.
Exhaust or muffler clogged with
carbon.
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.
PAGE 30 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE/MIXER)
TABLE 7. ENGINE TROUBLESHOOTING (Continued)
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Operation not satisfactory
Governor adjustment improper?
Governor spring defective?
Fuel flow erratic?
Adjust governor to correct lever.
Clean or replace ignition.
Check fuel line.
Rotational speed fluctuates.
Air taken in through suction
line?
Check suction line.
Dust in rotating part?
Spring spring failure?
Clean recoil starter assembly.
Replace sprial spring.
Recoil starter not working
properly.
TABLE 8. MIXER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Check that the gears and bearings are not worn . Replace as
necessary.
Defective gearbox?
Drum rotates rough.
Worn V-belt?
Loose pulley?
Replace V-belt.
Tighten or replace pulley.
Incorrect or no voltage being
supplied to electric motor?
Check that the electric motor has the correct supply voltage.
Inspect power source and extension cord. Push reset button on
electric motor.
Power to electric motor?
Fuel?
Check level of fuel in fuel tank. Add fuel if necessary. Make sure
fuel is being supplied to the engine. Check to ensure that the fuel
filter is not clogged.
Drum does not rotate at all.
Broken V-belt?
Replace V-belt.
Check that the gears and bearings are not broken. Replace as
necessary.
Defective gearbox?
Defective motor?
Replace motor.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
The contents of this parts
catalog are subject to change
without notice.
NOTE
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
, belong to the same assembly or kit.
+
, %, or
*
■
Note: If more than one of the same reference number is listed,
the last one listed indicates newest (or latest) part available.
If more than one of the same
NOTE
reference number is listed, the
last one listed indicates newest
(or latest) part available.
PAGE 32 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — SUGGESTED SPARE PARTS
MIX N' GO MIXER 1 TO 3 UNITS WITH HONDA
G100K2QA2,
MIX N' GO MIXER 1TO 3 UNITS
1 to 3 Units
Qty.
P/N
Description
V-BELT, A23 (ELECTRIC MOTOR)
1 to 3 Units
2 ............ DM1840 ...........
Qty......... P/N.............................. Description
2 ............ 9807354776 ................ SPARK PLUG HONDA
2 ............ 17631ZH7003 ............. TANK CAP (HONDA)
3 ............ 17211896000 .............. AIR CLEANER ELEMENT (HONDA)
2 ............ 17218ZE2505 ............. FILTER OUTER (HONDA)
4 ............ 10611 .......................... V-BELT (A-21)
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
2
1
E
N
E
G
L
S
F
P
A
IS
H
R
Ñ
A
O
-
A
N
L
W
A
Ç
A
-
R
N
IS
T
-
E
N
IN
G
A
T
C
!
T
IO
T
E
O
N
N
T
!
P
R
E
IO
A
N
R
D
U
!
A
IN
C
E
A
F
R
E
T
H
IR
D
D
U
E
E
E
C
R
IS
D
IM
IN
K
IE
L
O
F
WA
U
R
E
IN
J
R
S
AV
R
N
L
G
O
U
R
A
E
ER
L
R
D
Y
,
A
S
IN
G
IS
E
U
R
Q
L
S
T
M
A
!
U
LE
E
IS
!
E
S
R
D
IO
M
U
E
E
N
B
E
S
M
E
L
S
T
E
E
R
E
A
D
S
L
N
T
S
U
U
!
R
S
A
E
U
N
S
A
’U IO
L
R
TIL
D
U
N
D
D
E
E
IS
B
R
S
A
E
T
L
T
A
E
E
U
E
O
N
D
R
R
D
Y
L
E
IN
S
IT
N
IR
T
R
T
E
U
C
N
E
D
T
IO
E
E
T
R
N
C
E
M
A
O
L
M
M
P
A
N
U
R
N
A
L
D
E
E
U
N
A
D
L
R
E
C
IN
S
E
M
T
R
A
N
U
C
D’
U
E
C
IO
L
N
IN
E
S
S
T
R
U
C
T
IO
N
S
DCL25
1
3
S
N
ES
CCIONINSTRUCTIO
TRU
D’
INS
UE
AN
L
UAL DE
MAN
AL
ANU
M
E
C
N
!
IO
UCT EL
STR ER
M
CO
E
NDR
PRE
G
M
IN
N
R
!
!
IN
ND
D
AN
RST
DE
UN
A
T
D
WA
RM
A
MEN
Y
ENTE
ET
IR
E
L
E
A
S
E
R
L
IS
T
E
LE
IT
DO
D
R
AN
DEB
R
TEU
ARIO ISA
E
AV
REA
US
USU ’UTIL
L
T
M
EL
ES
R
SER NES
SIO
SSU
BLE
U
Y
,
JUR
LE
IN
EL
E
D
F
D
O
GO
LE
QUE
RISK
EL
RIS
RIES
THE
R
UCE
UE
IN
R
E
D
R
E
D
U
C
I
R
I
M
O
N
!
T
ARA
P
DE
G
IN
!
N
AFIN
!
N
AR
-
W
L
ENCIO
TENTIO
T
T
-
A
GLISH
EN
-
A
AÑO
AIS
ESP
FRANÇ
té
m
nt
x
v
n
r
p
e
t
e
t
ire
r
r
l
e
a
e
s
a
à
nt.
p
i
l
e
r
e
u
o
e
v
n
g
ce
l
o
n
d
e
u
n
u
t
e
d
lem
lv
t
n
b
x
l
e
e
’
m
v
q
e
s
s
s
s
s
e
t
l
l
la
u
r
s
)
l
o
e
à
n
n
m
q
i
6
e
0
l
é
r
m
m
l
é
i
a
o
s
5
o
e
s
c
e
l
e
d
f
r
a
l
i
e
v
v
e
e
m
I
25
e
t
l
a
1
O
CL2
l
h
s
i
r
E
C
f
é
ter
é
1
,
C
m
0
4
R
R
’u
u
.
e
s
v
u
o
e
u
E
c
à
r
N
.
H
R
U
d
u
a
E
t
r
d
’
n
E
1
I
D
A
E
UROIE.
t
e
i
f
n
e
n
m
U
a
o
.
A
D
XEUR
G
s
A
CO
a
ê
r
s
.
t
s
o
S
E
t
x
n
b
t
t
I
r
o
p
N
8
e
R
C
N
A
e
n
e
e
T
é
r
a
O
l
o
d
t
D
B
A
a
u
p
p
h
d
u
u
r
l
u
s
X
Z
A
LA
i
i
À
a
n
é
L
b
é
i
I
.
EL
o
p
n
d
a
o
x
c
m
n
a
c
h
E
.
o
i
m
I
M
M
D
E
a
f
t
s
m
s
l
l
U
e
l
a
e
e
s
É
a
r
r
t
A
u
0
2
E
E
L
A
L
LE
t
a
s
l
e
i
m
i
E
u
e
u
a
r
’
n
R
l
x
po
e
R
(
A
R
E
V
E
U
A
C
l
u
u
s
r
o
l
f
M
e
t
e
i
u
u
r
U
b
l
u
A
0
R
J
R
E
A
ER
E
e
n
x
e
s
é
o
t
d
c
a
T
e
m
ç
1
s
OV
A
.
A
A
UV
l
e
l
t
o
E
e
s
e
A
BE
u
n
u
u
l
n
m
s
e
n
m
e
l
v
o
M
l
e
o
l
:
D
o
d
t
!
M
O
Z
O
V
r
s
a
e
u
r
i
m
R
L
!
E
a
r
m
j
u
s
l
e
u
t
r
i
E
L
L
C
m
V
E
VID
L
m
p
e
o
v
l
m
E
S
o
q
n
s
s
r
s
e
s
y
à
n
s
5
4
B
C
A
O
IL
A
l
p
5
E
V
U
I
S
n
u
a
z
t
s
.
Z
u
v
d
u
o
t
j
u
r
e
I
N
M
’
NS
e
Z
e
m
A
(
S
R
A
e
u
a
e
e
I
o
E
h
v
é
E
r
t
u
e
u
e
q
l
T
)
N
m
r
L
r
I
a
z
c
I
a
E
t
e
d
s
t
d
e
u
ram
2
s
L
S
u
s
l
s
A
d
G
E
p
E
m
u
s
r
T
a
e
E
o
v
n
l
r
o
d
é
1
2
.
L
n
a
3
o
V
e
é
U
’
t
U
F
a
u
j
d
C
m
p
m
4
5
.
A
d
r
v
s
u
4
C
O
E
U
6
N
e
a
r
u
a
N
5
2
R
R
E
m
R
a
a
t
u
5
T
O
O
I
R
.
V
a
s
A
u
m
u
e
1
T
T
R
E
IQU
C
T
T
C
RIQ
s
t
o
a
o
e
f
f
E
T
M
É
O
T
d
i
n
I
ré
E
M
EC
.
l
l
í
LECTR
r
i
e
d
.
v
j
c
u
.
r
e
d
ÉL
d
a
o
o
o
r
e
l
d
a
s
s
e
d
r
l
n
m
e
l
c
te
c
c
n
l
e
l
c
p
nte
e
e
o
i
e
z
s
s
r
d
z
n
n
t
i
i
do
)
m
a
a
e
t
,
b
m
e
.
a
l
e
6
s
l
a
i
d
m
s
a
d
l
a
e
i
o
i
b
o
i
r
r
r
l
b
é
c
a
n
e
a
a
n
m
é
e
s
r
n
g
a
s
e
A
a
i
r
a
e
e
e
r
e
a
m
0
m
u
d
e
d
I
e
t
d
p
b
A
u
0
6
u
l
s
u
t
m
e
e
mp
N
2
.
d
a
e
d
e
d
o
e
s
O
a
c
ltro
e
d
N
6
e
a
v
q
i
a
l
Ó
(
n
s
s
a
i
n
S
d
r
r
a
t
l
C
d
i
a
I
)
t
t
S
e
u
a
n
a
r
a
G
g
a
á
d
i
y
I
é
c
e
N
e
8
s
r
an
d
a
a
s
d
E
a
p
n
o
e
e
C
s
p
e
E
o
i
t
ó
n
o
m
c
e
o
a
n
d
e
z
a
S
t
e
n
p
y
t
L
e
e
i
T
a
m
0
8
m
q
d
s
e
e
b
A
e
e
a
a
n
a
E
e
n
n
X
A
u
0
.
e
y
R
e
0
o
a
s
a
e
I
a
o
n
i
,
o
e
jo:
z
s
l
e
O
T
E
(
d
o
e
d
i
o
e
o
Q
u
n
l
e
á
m
a
t
n
c
l
x
b
D
)
a
r
o
o
o
Á
á
z
u
d
s
d
e
0
o
s
A
m
m
d
M
o
c
a
MO
a
O
1
s
n
p
e
d
u
p
s
l
p
m
a
m
a
a
g
a
b
t
.
ño
m
Ñ
b
o
e
e
o
l
a
A
a
é
p
g
s
.
s
e
o
l
a
i
l
c
l
r
e
a
n
c
e
o
gra
5
6
m
e
t
e
n
r
n
g
s
E
e
n
a
a
p
n
s
q
l
c
o
t
i
M
A
u
7
2
j
u
ú
j
t
A
P
e
c
n
u
a
s
r
m
e
a
t
v
e
ld
T
2
e
a
q
5
M
e
m
s
a
a
N
M
u
e
c
n
E
g
E
r
l
o
e
1
e
a
2
L
e
s
.
.
3
t
M
N
I
g
e
e
e
l
R
d
e
a
t
e
d
u
s
r
s
o
O
N
s
a
n
M
n
r
z
o
u
m
é
o
e
e
4
5
.
s
e
M
a
E
e
I
S
m
m
a
m
p
m
o
c
e
m
e
r
u
0
4
s
l
E
m
N
5
2
A
l
a
I
1
c
e
s
r
e.
r
a
l
e
.
f
g
er
w
p
bj
i
e
b
e
o
rt
i
m
l
g
r
r
.
r
o
c
n
p
h
e
s
)
E
e
w
t
Y
I
e
L
T
i
o
a
i
p
i
u
,
o
t
r
.
e
W
e
E
r
p
s
o
n
m
k
e
t
d
n
s
6
f
m
F
L
L
D
I
ME
E
d
a
h
n
a
a
i
r
t
o
e
o
2
6
D
O
Ñ
E
T
S
p
N
N
R
D
ES
o
e
w
r
E
s
d
n
f
c
s
A
A
R
I
E
N
g
r
r
i
6
A
E
O
E
0
C
N
e
t
.
s
y
e
s
N
d
x
o
b
n
a
r
E
L
G
L
T
A
C
P
E
V
G
IE
e
u
t
c
e
a
n
r
N
f
m
n
w
r
R
s
r
p
Z
e
s
O
0
E
N
E
U
N
I
DIEN
b
r
v
a
e
e
E
o
e
a
T
i
o
r
I
r
t
e
E
V
9
R
N
Z
Z
R
G
Y
RIO
TID
d
.
n
W
e
P
E
C
J
B
N
I
A
A
a
e
d
r
n
e
n
n
n
a
n
C
o
f
O
E
V
R
A
E
A
n
e
u
t
I
M
A
V
D
8
0
m
O
A
N
E
S
D
QU
a
e
y
r
e
L
n
a
n
a
n
b
r
r
R
o
0
8
M
N
L
L
À
D
R
Z
o
r
i
b
t
r
a
I
1
4
E
R
I
T
O
A
K
C
W
s
z
n
f
s
d
e
V
S
A
s
c
e
.
n
l
R
s
x
5
c
O
N
0
W
E
E
G
E
P
0
S
F
E
V
r
o
u
l
s
n
m
k
c
G
e
f
m
d
e
,
C
m
r
o
(
E
Ô
R
P
RI
a
r
e
e
s
v
h
c
g
b
t
u
e
.
e
E
o
i
f
ns
N
r
)
C
R
VÉ
É
n
u
s
O
o
u
x
u
i
n
l
e
d
r
q
t
o
a
I
W
t
t
m
s
r
r
x
S
1
e
e
a
e
e
r
h
R
Y
r
t
p
i
t
o
c
c
t
N
m
K
r
a
f
e
V
u
n
T
O
o
s
e
c
p
r
m
a
E
o
5
6
e
f
A
S
1
2
M
b
e
E
L
k
n
l
f
S
r
f
c
e
2
3
.
a
A
Y
A
b
c
u
E
2
.
5
6
M
i
O
n
W
L
i
s
S
e
d
D
W
e
e
c
r
s
v
A
d
a
l
A
W
A
a
u
i
w
2
e
e
t
M
s
L
1
e
m
T
A
e
.
0
b
o
5
4
I
E
N
2
R
T
R
R
C
5
O
O
T
1
C
T
O
I
R
IQU
E
L
O
T
E
R
E
M
M
É
O
CT
E
M
L
É
4
PAGE 34 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NAMEPLATE AND DECALS.
NO
PART NO
DCL251
510165
PART NAME
QTY.
1
1
1
1
REMARKS
1
*
2
*
3
DECAL:WARNING MQ
DECAL: MQ MIX N GO
DECAL: NAMEPLATE
DECAL:WARNING MAINTENANCE
CONTACT MQ PARTS DEPT.
4
DCL250
*
SEE DECAL ILLUSTRATIONS ON PAGES 11 AND 12.
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MIXER ASSY.
MIXER ASSY.
PAGE 36 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
MIX N' GO MIXER — MIXER ASSY.
MIXER ASSY.
NO.
1#
2#
3#
4#
5#
6#
7
PART NO.
PART NAME
QTY.
REMARKS
DM3150
DM1356
DM1912
DM355
HEX HEAD BOLT M12 x 70
OIL FILLER PLUG M14 x 2 x 15L
HEX NUT M10
1
1
2
3
2
1
HEX HEAD BOLT M8 x P1.25 x 24L
FLAT WASHER M12
DM3151
DM3152
SP9012
HEX NUT M12
TOGGLE SWITCH .................................... 1 ......... INCLUDES ITEM W/
*
8
SWITCH, BOOT
1
1
*
9#
DM1320
DM1357
DM1380
DM1821
DM1822
DM2020
DM1840
DM1332
DM1810
DM1353
DM1352
DM1331
DM1310
DM1351
DM1333
DM1351
DM1720
DM1711
DM1641
DM2021
DM1110
DM1911
DM1141
DM1527
DM1524
DM1400
DM1414
DM1613
DM1630
DM1631
DM1632
DM1620
DM1640
DM1221
DM1212
DM1213
DM1231
DM3050
DM3051
DM3000
10649
GEAR BOX BACK COVER
GEAR BOX SEAL
BELT GUARD
10#
11
1
12
DRIVE PULLEY........................................ 1 ......... ELECTRIC MOTOR ONLY
13
SET SCREW M6 x 12L
BOLT M6 x 18
1
2
14
15
V-BELT, A23 ............................................. 1 ......... ELECTRIC MOTOR ONLY
16#
17#
18#
19#
20#
21#
22#
23#
24
NUT M12
1
1
1
1
1
1
1
1
1
2
2
2
2
1
3
1
2
2
1
2
2
2
2
2
1
2
1
1
1
1
4
4
1
1
1
1
GEARBOX PULLEY
OIL SEAL 20 x 42.5 x 10
BEARING RACE 6004
WORMSHAFT
GEARBOX CASE
BEARING RACE 6006
WORMSHAFT (DRUM)
BEARING RACE 6006
WHEEL RETAINER
WHEEL, RUBBER
25
26
27
HEX NUT M8
28
NUT
28
MAIN FRAME
29
HEX HEAD BOLT M10 x P1.5 x 40L
DRUM LOCK
30
31
HEX NUT M10
32
BOLT
33
STEEL DRUM
34
STEEL DRUM BLADE
HANDLE GRIP, RUBBER
TOP COVER CLAMP
SCREW 5.5 x 25
35
36
37
38
LOCKWASHER
39
TOP COVER, PLASTIC
BOLT M8 SPECIAL DOME HEAD
STAND, ADAPTER
STAND, BOTTOM LH (2 BOSS)
STAND, BOTTOM RH (1 BOSS)
CLIP LINCH PIN
40
41
42
43
44
45
NUT M8BOLT M8 x 35
BOLT M8 x 35
46
47
ENGINE MOUNT (GASOLINE)
ENGINE, 2.5 HP HONDA G100K2QA2
RETAINER RING
48
49#
50
DM1358
34579
MOTOR, ELECTRIC 3/4 H.P.
51
DM1810
MS01
GEARBOX ASSEMBLY............................ 1 ......... INCLUDES ITEMS/#
V-BELT, A24 ............................................. 1 ......... GASOLINE ENGINE ONLY
DRIVE PULLEY........................................ 1 ......... GASOLINE ENGINE ONLY
52
53
EM901006
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 38 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
QTY.
REMARKS
15721896010
17211896000
17212896000
17220ZG0000
17231ZG0000
90325044000
9405005000
9410106800
TUBE, BREATHER
ELEMENT, AIR CLEANER
GRID, AIR CLEANER
1
1
1
HOUSING, AIR CLEANER .............................. 1 .............INCLUDES ITEMS W/
*
5
COVER, AIR CLEANER
WING NUT, TOOL BOX SETTING
NUT, FLANGE 5MM
1
1
2
1
6
*
7
8
WASHER, PLAIN 6MM
*
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 40 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
5
6
7
8
8
8
8
8
8
8
8
9
PART NO.
PART NAME
QTY.
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
1
REMARKS
12209ZG1H11
14111ZC0000
14711ZG1H10
14721ZG1H10
14732ZC0000
14751896000
14771ZG0000
14801892000
14803892000
14806892000
14809892000
14812892000
14815892000
14818892000
14820892000
90452ZG0000
90452ZG0000
SEAL, VALVE STEM
CAMSHAFT
VALVE, IN.
VALVE, EX.
LIFTER, VALVE
SPRING, VALVE
RETAINER, VALVE SPRING
ADJUSTER, TAPPET CLEARANCE 3.15
ADJUSTER, TAPPET CLEARANCE 3.25
ADJUSTER, TAPPET CLEARANCE 3.34
ADJUSTER, TAPPET CLEARANCE 3.43
ADJUSTER, TAPPET CLEARANCE 3.52
ADJUSTER, TAPPET CLEARANCE 3.61
ADJUSTER, TAPPET CLEARANCE 3.72
ADJUSTER, TAPPET CLEARANCE 3.82
WASHER 12MM
10
WASHER 12MM
1
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 42 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
16010ZG0812
16011ZE0005
16013ZG0811
16015ZG0811
16016ZG0W00
16024ZE1811
16028ZG0811
16044ZG0W00
16100ZG0W02
16124ZE0005
16166ZG0W01
16173ZG0811
16211ZG0020
16212ZG0800
16221ZG0801
16269ZG0800
16953ZG0812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZG0811
93500030060H
99101ZG00500
99101ZG00520
99101ZG00550
99204ZE00350
GASKET SET
1
1
1
1
1
1
1
1
*
2
VALVE SET, FLOAT
FLOAT SET
CHAMBER SET, FLOAT
SCREW SET
SCREW SET, DRAIN
SCREW SET
CHOKE SET
CARBURETOR ASSEMBLY BF11B B ............. 1.............INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
*
3
*
4
*
6
*
7
*
8
*
9
*
10
*
11
*
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
12
*
13
14
O-RING
*
INSULATOR, CARBURETOR
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, AIR CLEANER
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3X6
JET, MAIN #50 (OPTIONAL)
JET, MAIN #52 (OPTIONAL)
JET, MAIN #55
15
16
17
18
*
19
*
20
*
21
*
22
*
23
*
24
24
24
25
*
*
JET SET, PILOT #35
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 44 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
1
2
3
4
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
QTY.
REMARKS
16551ZG0000
16555ZG0000
16561ZG0000
16562ZG0000
16570ZG0W00
16571ZG0000
16572ZG0000
16574ZE1000
16575ZG0000
16578ZE1000
16576891000
16584883300
16594883010
90015ZE5010
90605230000
93500040080A
93500050250A
93500050160A
9405006000
1
1
1
1
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSEMBLY, STANDARD ................ 1.............INCLUDES ITEMS W/
LEVER, CONTROL (STANDARD)
BASE, CONTROL (STANDARD)
SPRING, LEVER
WASHER, CONTROL LEVER
SPACER, CONTROL LEVER
HOLDER, CABLE
SPRING, CONTROL ADJUSTING
HOLDER, WIRE (OPTIONAL)
BOLT, GOVERNOR ARM
CIRCLIP 5MM (OPTIONAL)
SCREW, PAN 4X8 (OPTIONAL)
SCREW, PAN 5X25
5
6
*
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
*
7
8
*
*
9
*
10
*
11
*
12
*
13
15
18
20
21
*
22
*
SCREW, PAN 5X16
NUT, FLANGE 6MM
BOLT, FLANGE 6X12 (CT200)
23
*
24
90013883000
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 46 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER (1) ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
QTY.
REMARKS
11300ZG0010
11381ZG0800
15600ZG4003
15620ZG0003
15625ZG0000
15625ZE1003
16511896000
16512ZG0000
16513ZE1000
16531ZG0000
16541896000
90015883000
90131ZE1000
90601ZE1000
90602ZE1000
91202892004
9410105000
COVER ASSEMBLY, CRANKCASE ................. 1.............INCLUDES ITEMS W/
*
#
GASKET, CASE COVER
CAP ASSEMBLY, OIL FILLER ......................... 1.............INCLUDES ITEMS W/
CAP, OIL FILLER
1
1
1
1
2
1
2
1
1
6
2
2
1
1
1
1
1
1
6
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, FLANGE 6X28
BOLT, DRAIN PLUG
WASHER, DRAIN PLUG10.2MM
CLIP, GOVERNOR HOLDER
OIL SEAL 17X30X6 (NOK)
WASHER, PLAIN 5MM
WASHER, PLAIN 6MM
PIN, LOCK 8MM
7
8
9
#
*
10
11
12
13
14
15
16
*
17
18
19
21
22
*
*
*
9410106800
9425108000
961006203000
BEARING, RADIAL BALL 6203
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 48 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
4
PART NO.
PART NAME
QTY.
REMARKS
13310ZG0601
90745ZE1600
961006203000
CRANKSHAFT, Q-TYPE .................................... 1...........INCLUDES ITEMS W/
*
KEY 4.78X4.78X38
BEARING, RADIAL BALL
1
1
5
*
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 50 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12000ZG0020
12133896306
12221ZG0030
12281ZC0003
12351ZG0810
12361ZG0000
12370ZG0000
12375ZG0010
90002892000
90041896000
91202892004
91231816000
9430108140
CYLINDER ASSEMBLY.................................... 1.............INCLUDES ITEMS W/
*
3
*
4
5
6
8
GUIDE, VALVE OS (OPTIONAL)
CYLINDER HEAD
2
1
1
1
1
1
1
4
2
1
1
2
6
4
1
GASKET, CYLINDER HEAD
BED, ENGINE Q-TYPE
COVER, TAPPET ROOM
SEPARATOR, INNER
GASKET, TAPPET COVER
BOLT, FLANGE 5X10
BOLT, STUD 5X80
OIL SEAL 17X30X6 (NOK)
OIL SEAL
PIN A, DOWEL 8X14
BOLT, FLANGE 6X35
BOLT, FLANGE 8X18
SPARK PLUG, BRMR4A (NGK)
9
10
11
12
13
14
*
17
18
19
21
958010603500
957010801800
9807354776
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 52 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
5
7
8
9
10
PART NO.
PART NAME
COVER, FAN *R8* (BRIGHT RED)
SHROUD
QTY.
REMARKS
19610ZG0W20ZB
19631ZG0000
19721ZG0W20
36100ZE1015
90013883000
90652SB2023
90013883000
1
1
1
1
2
1
4
COVER, TOP
SWITCH ASSEMBLY, ENGINE STOP
BOLT, FLANGE 6X12 (CT200)
CLIP, TUBE 7MM
BOLT, FLANGE 6X12 (CT200
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 54 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
5
6
PART NO.
PART NAME
QTY.
REMARKS
19511ZG0W00
28450ZG0822
31100ZG0010
90741035000
9405012000
FAN, COOLING
1
1
1
1
1
PULLEY, STARTER
FLYWHEEL
KEY, WOODRUFF 3X5
NUT, FLANGE 12MM
7
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 56 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
5
6
7
8
PART NO.
PART NAME
TANK, FUEL *NH31* (MCKINLEY WHITE)
JOINT, FUEL TANK
O-RING 13.5X1.5 (ARAI)
CAP, FUEL FILLER .......................................... 1.............INCLUDES ITEMS W/
CAP, FUEL FILLER
GASKET, FUEL FILLER CAP
FILTER, FUEL
NUT, FLANGE 6MM
BULK HOSE, FUEL (4.5X3000) (4.5X55)
CLIP, TUBE B8
QTY.
REMARKS
17510ZG0W00ZA
16955ZE1000
91353671003
17620ZH7023
17620ZE2W00
17631ZH7003
17672ZE2W01
9405006000
1
1
1
*
9
1
1
1
2
1
2
1
10
12
*
16
17
19
20
950014500360M
9500202080
957010601400
BOLT, FLANGE 6X14
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
PAGE 58 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
061A1ZG0801
11381ZG0800
12281ZC0003
12375ZG0010
16212ZG0800
16221ZG0801
16269ZG0800
18381ZG0800
GASKET KIT .................................................... 1.............INCLUDES ITEMS W/
*
1
GASKET, CASE COVER
GASKET, CYLINDER HEAD
GASKET, TAPPET COVER
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, AIR CLEANER
GASKET, MUFFLER
1
1
1
1
1
1
1
*
2
*
3
*
5
*
7
*
8
*
10
*
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 60 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
3
PART NO.
PART NAME
QTY.
REMARKS
30500ZG0W01
30563ZG0000
30701888014
30702888003
36101ZG0000
90121952000
COIL ASSEMBLY, IGNITION............................ 1.............INCLUDES ITEMS W/
*
GROMMET, IGNITION WIRE
CAP, IGNITION (TOYO)
TERMINAL, PLUG
WIRE, STOP SWITCH
BOLT, FLANGE 6X25
1
1
1
1
2
5
*
6
*
7
8
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 62 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
2
*
4
*
6
*
8
10
11
12
18310ZG0830
18320ZG0810
18321896000
18331896620
18381ZG0800
90046ZG0000
90002ZG0003
93500060060A
9405006000
MUFFLER (W/PROTECTOR)
PROTECTOR, MUFFLER
SEPARATOR, MUFFLER
DEFLECTOR, MUFFLER (OPTIONAL)
GASKET, MUFFLER
1
1
1
1
1
2
2
2
2
BOLT, STUD 6X50
SCREW, TAPPING 4X8 (OPTIONAL)
SCREW, PAN 6X6
NUT, FLANGE 6MM
MUFFLER ASSEMBLY..................................... 1.............INCLUDES ITEMS W/
14
15
20
*
18300ZG0U01
*
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 64 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
5
5
PART NO.
PART NAME
QTY.
REMARKS
13010ZC0003
13011ZC0003
13012ZC0003
13013ZC0003
13101ZC0003
13102ZC0003
13103ZC0003
13104ZC0003
13111892000
13115147000
13200ZG0000
13200ZG0305
RING SET, PISTON -STANDARD
RING SET, PISTON - OS 0.25 ( OPTIONAL)
RING SET, PISTON - OS 0.50 (OPTIONAL)
RING SET, PISTON - 0.75 (OPTIONAL)
PISTON - STANDARD
1
1
1
1
1
1
1
1
1
2
PISTON - OS 0.25 (OPTIONAL)
PISTON- OS 0.50 (OPTIONAL)
PISTON- 0.75 (OPTIONAL)
PIN, PISTON
CLIP, PISTON PIN 10MM
ROD ASSY., CONNECTING STANDARD ......... 1.............INCLUDES ITEMS W/
ROD ASSY., CONNECTING (UNDER SIZE) .... 1.............INCLUDES ITEMS W/
OPTIONAL
*
*
8
90001ZG0000
BOLT, CONNECTING ROD
2
*
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 66 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER (3) ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
28400ZGOWO2ZC STARTER ASSY., RECOIL *R8* ..................... 1 .............INCLUDES ITEMS W/
*
2
28410ZGOWO2ZC CASE, RECOIL STARTER *R8*
1
1
1
1
1
1
1
1
3
1
*
3
28421ZGOWO2
28422ZGOWO2
28433ZGOWO2
28441ZH8003
28442ZH8003
28461ZGOWO2
28462ZGOWO2
9000-ZH8003
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
GRIP, STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
BOLT, FLANGE 6X8
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
957010600800
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — LABELS
LABELS
PAGE 68 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA G100K2QA2 ENGINE — LABELS
LABELS
NO.
2
4
7
8
PART NO.
PART NAME
QTY. REMARKS
87521ZG0W50
87522ZE1810
87528ZG0810
87528883661
87532ZG0810
EMBLEM
1
MARK, CAUTION (EXTERNAL)
MARK, EXTERNAL
MARK, CHOKE
1
1
1
1
9
MARK, THROTTLE( ENGLISH, FRENCH, GERMAN)
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 1, 2000
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
4. Freight is at the sender’s expense. All PRICINGANDREBATES
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
Terms of payment for parts are net 10 days.
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspecific
5. Parts must be in new and resalable dateandallordersreceivedonorafterthatdate
condition,intheoriginalMultiquippackage willbebilledattherevisedprice. Rebatesfor
(ifany),andwithMuiltiquippartnumbers price declines and added charges for price
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
clearlymarked.
increaseswillnotbemadeforstockonhandat
thetimeofanypricechange.
6. Thefollowingitemsarenotreturnable:
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
a. Obsolete parts. (If an item is listed
inthepartspricebookasbeing
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
andotherrubberparts)thatwere
purchasedmorethansixmonths
priortothereturndate.
MINIMUMORDER
SPECIALEXPEDITINGSERVICE
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
A$20.00to$50.00surchargewillbeaddedto
theinvoiceforspecialhandlingincludingbus
c. Anylineitemwithanextendeddealer shipments, insured parcel post or in cases
netpriceoflessthan$5.00.
where Multiquip must personally deliver the
partstothecarrier.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
Returnshipmentswillbeacceptedandcredit
will be allowed, subject to the following
provisions:
LIMITATIONSOFSELLER’SLIABILITY
f.
Paint,chemicals,andlubricants.
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
1. AReturnedMaterialAuthorizationmust
beapprovedbyMultiquippriortoshipment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Sales that defines item numbers,
quantities,anddescriptionsoftheitemsto
bereturned.
8. Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within5days,thematerialwillbereturned
tothesenderathisexpense.
LIMITATIONOFWARRANTIES
a. Thepartsnumbersanddescriptions
mustmatchthecurrentpartsprice
list.
Nowarranties,expressorimplied,aremadein
connection with the sale of parts or trade
accessories nor as to any engine not
manufacturedbyMultiquip.Suchwarranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connectionwiththesaleofitsproducts.Apart
fromsuchwrittenstatementofwarranty,there
arenowarranties,express,impliedorstatutory,
which extend beyond the description of the
productsonthefacehereof.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. Thelistmuststatethereason(s)for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhich
theitemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. Thelistmustincludethenameand
phonenumberoftheperson
requestingtheRMA.
3. A copy of the Return Material
Authorizationmustaccompanythereturn
shipment.
PAGE 70 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE
800-478-1244 or 310-537-3700
FAX: 310- 537-4259
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
MAIN
800-421-1244 or 310-537-3700
FAX: 310-537-3927
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Cooktop km 530 User Manual
Miele Washer W 487 WPS User Manual
MTD Log Splitter 246 631 000 User Manual
Nikon Digital Camera View DX User Manual
Nilfisk ALTO Vacuum Cleaner GD 10 Back User Manual
Olivetti Printer P216 User Manual
Oster Juicer 3181 User Manual
Packard Bell Computer Drive DVX 460 User Manual
Panasonic Telephone KX T2365A User Manual
Parasound Stereo Amplifier 5250 V2 User Manual