Multiquip Music Mixer MC 44S User Manual
OPERATION AND PARTS MANUAL  
MC-44S  
CONCRETE MIXER  
Revision #8 (09/15/11)  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — TABLE OF CONTENTS  
ComponetDrawings  
MULTIQUIP MC-44S  
Nameplate and Decals....................................... 34-35  
Mixer Assembly (Steel Drum) ............................ 36-37  
Main Frame Assembly ....................................... 38-39  
Axle Assembly .................................................... 40-41  
Cabinet Assembly .............................................. 42-43  
Gas Engine Mounting Plate Asasembly............ 44-45  
Electric Motor Mounting Plate Asasembly ........ 46-47  
Concrete Mixer  
Proposition 65 Warning ............................................. 2  
Table Of Contents ..................................................... 4  
Parts Ordering Procedures ....................................... 5  
Specifications ............................................................ 6  
Dimensions (Mixer) ................................................... 7  
Safety Message Alert Symbols ................................. 8  
Rules For Safe Operation .................................... 9-10  
Operation and Safety Decals .................................. 11  
General Information ................................................ 12  
Mixer Basic Components ........................................ 13  
Basic Engine Components...................................... 14  
Handwheel Assembly.............................................. 15  
Towing Guidelines ................................................... 16  
Safety Chain Connection ........................................ 17  
Electric Motor ..................................................... 18-19  
Pre-Inspection (Gasoline Engine) ........................... 20  
Initial Start-up (Gasoline Engine)............................ 21  
Initial Start-up (Electric Motor) ................................ 22  
Operation ................................................................ 23  
Maintenance (Engine)........................................ 24-25  
Maintenance (Mixer) .......................................... 26-28  
Troubleshooting (Engine)........................................ 30  
Troubleshooting (Engine/Mixer) .............................. 31  
Explanation Of Code In Remarks Column .............. 32  
Suggested Spare Parts ........................................... 33  
HONDAGX120K1QX2 Engine  
Air Cleaner Assembly......................................... 48-49  
Camshaft Assembly ........................................... 50-51  
Carburetor Assembly ......................................... 52-53  
Control Assembly ............................................... 54-55  
Crankcase Cover Assembly............................... 56-57  
Crankshaft Assembly ......................................... 58-59  
Cylinder Barrel Assembly................................... 60-61  
Cylinder Head Assembly.................................... 62-63  
Fan Cover Assembly .......................................... 64-65  
Flywheel Assembly ............................................ 66-67  
Fuel Tank Assembly ........................................... 68-69  
Ignition Coil Assembly ........................................ 70-71  
Muffler Assembly ............................................... 72-73  
Piston Assembly................................................. 74-75  
Recoil Starter Assembly..................................... 76-77  
Gasket Kit Assembly .......................................... 78-79  
Labels Assembly ................................................ 80-81  
Terms and Condition Of Sale  
—
Parts .................... 82  
Specification and part number  
are subject to change without  
notice.  
PAGE 4 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
Ordering parts has never been easier!  
Choose from three easy options:  
Effective:  
January 1st, 2006  
Best Deal!  
Order via Internet (Dealers Only):  
Order parts on-line using Multiquip’s SmartEquip website!  
If you have an MQ Account, to obtain a Username  
and Password, E-mail us at: parts@multiquip.  
com.  
■ View Parts Diagrams  
■ Order Parts  
■ Print Specification Information  
To obtain an MQ Account, contact your  
District Sales Manager for more information.  
Use the internet and qualify for a 5% Discount  
on Standard orders for all orders which include  
complete part numbers.*  
Goto www.multiquip.com and click on  
to log in and save!  
Order Parts  
Note: Discounts Are Subject To Change  
Fax your order in and qualify for a 2% Discount  
on Standard orders for all orders which include  
complete part numbers.*  
Order via Fax (Dealers Only):  
All customers are welcome to order parts via Fax.  
Domestic (US) Customers dial:  
1-800-6-PARTS-7 (800-672-7877)  
Note: Discounts Are Subject To Change  
Domestic (US) Dealers Call:  
Order via Phone:  
1-800-427-1244  
Non-Dealer Customers:  
International Customers should contact  
their local Multiquip Representatives for  
Parts Ordering information.  
Contact your local Multiquip Dealer for  
parts or call 800-427-1244 for help in  
locating a dealer near you.  
When ordering parts, please supply:  
❒
Dealer Account Number  
❒
Specify Preferred Method of Shipment:  
❒
❒
❒
❒
❒
Dealer Name and Address  
✓ UPS/Fed Ex  
✓ DHL  
✓ Truck  
■
■
Priority One  
Ground  
Shipping Address (if different than billing address)  
Return Fax Number  
■ Next Day  
Second/Third Day  
Applicable Model Number  
■
Quantity, Part Number and Description of Each Part  
NOTICE  
All orders are treated as Standard Orders and will  
ship the same day if received prior to 3PM PST.  
WE ACCEPT ALL MAJOR CREDIT CARDS!  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — SPECIFICATIONS  
Table 1. Specifications (Engine/Electric Motor)  
Model  
HONDA GX120K1QX2  
Baldor 34F324-5596  
Air-cooled 4 stroke, Single  
Cylinder, OHV, Horizontal Shaft  
Gasoline Engine  
1/2 HP, Single-phase 115  
VAC, Electric Motor  
Type  
2.7 in. X 1.7 in.  
(60 mm x 42 mm)  
Bore X Stroke  
N/A  
Displacement  
Max Output  
7.3 cu. in. (119 cc)  
3.9 H.P./3,600 rpm  
N/A  
1/2 HP/1725 R.P.M.  
Engine/Electric  
Motor  
Fuel Tank Capacity  
Fuel  
0.63 U.S. Gallons (0.60 Liters)  
Unleaded Automobile Gasoline  
0.63 qt. (0.6 liter)  
N/A  
N/A  
N/A  
Lube Oil Capacity  
Speed Control  
Method  
Centrifugal Fly-weight Type  
N/A  
Starting Method  
Input Voltage  
Recoil Start  
N/A  
Electric  
115 VAC Single Phase  
Dimension  
(L x W x H)  
11.7 x 13.4 X 12.5 in.  
(297 X 341 X 318 mm)  
13.87 x 7.56 X 8.62 in.  
(352 X 192 X 219 mm)  
Dry Net Weight  
28.7 lbs (13.0 Kg.)  
Approx. 12 lbs (5.4 kg.)  
Table 2. MC-44S Mixer Specifications  
60 in. (1,525 mm)  
Height  
Width  
51 in. (1,296 mm)  
Length  
66 in. (1,677 mm)  
Maximum Drum Capacity  
Maximum Mixing Capacity  
Bag Capacity  
6.35 cu. ft. (180 liters)  
4 cu. ft. (113 liters)  
(1/3 to 1/2 bag)  
Weight - With Engine/ElectricMotor  
495 lbs. (224 Kg.)  
PAGE 6 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — DIMENSIONS (MIXER)  
See Table 2 for mixer dimensions  
Figure 1. Mixer Dimensions  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — SAFETY MESSAGE ALERT SYMBOLS  
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!  
HAZARD SYMBOLS  
Safety precautions should be followed at all times when  
operating this equipment. Failure to read and understand the  
Safety Messages and Operating Instructions could result in  
injury to yourself and others.  
Rotating Parts  
This Owner's Manual has been  
developed to provide complete  
instructions for the safe and  
efficient operation of the Multiquip  
Model MC-44S (Steel) Concrete  
Mixer.  
NEVER operate equipment with covers, or  
guards removed. Keep fingers, hands, hair and  
clothing away from all moving parts to prevent  
injury.  
Before using these mixers,  
ensure that the operating  
individual has read and  
understands all instructions in  
this manual.  
Accidental Starting  
ALWAYS place the circuit breaker or power  
ON/OFF switch in the OFF position when the  
pump is not in use.  
SAFETY MESSAGE ALERT SYMBOLS  
Sight and Hearing hazard  
The three (3) Safety Messages shown below will inform you  
about potential hazards that could injure you or others. The  
Safety Messages specifically address the level of exposure to  
the operator, and are preceded by one of three words: DANGER,  
WARNING, or CAUTION.  
ALWAYS wear approved eye and hearing  
protection.  
DANGER: You WILL be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Respiratory Hazard  
ALWAYS wear approved respiratory  
protection.  
WARNING: You CAN be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Equipment Damage Messages  
CAUTION: You CAN be injured if you  
Other important messages are provided throughout this manual  
to help prevent damage to your mixer, other property, or the  
surrounding environment.  
do not follow directions.  
Potential hazards associated with the Multiquip MC-44S  
concrete mixer operation will be referenced with Hazard Symbols  
which appear throughout this manual, and will be referenced in  
conjunction with Safety Message Alert Symbols.  
This mixer, other property, or the  
surrounding environment could  
be damaged if you do not follow  
instructions.  
PAGE 8 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — RULES FOR SAFE OPERATION  
■
NEVER touchthehotexhaustmanifold,  
muffler or cylinder.Allow these parts to  
cool before servicing engine or mixer.  
DANGER:  
Failure to follow instructions in this manual may  
lead to serious injury or even death! This  
equipment is to be operated by trained and  
qualified personnel only!This equipment is for  
industrial use only.  
The following safety guidelines should always be used when  
operating the Multiquip MC-44S Concrete Mixer:  
■
■
HighTemperatures – Allow the engine to cool before adding  
fuel or performing service and maintenance functions. Contact  
with hot components can cause serious burns.  
GENERAL SAFETY  
■
DO NOT operate or service this equipment before  
readingthisentiremanual.  
The engine of this mixer requires an adequate free flow of  
cooling air. NEVER! operate the mixer in any enclosed or  
narrow area where free flow of the air is restricted. If the air  
flow is restricted it will cause  
■
■
This equipment should not be operated by  
persons under 18 years of age.  
NEVER operate this equipment without proper  
protective clothing, shatterproof glasses, steel-  
toed boots and other protective devices required  
by the job.  
serious damage to the  
mixer or engine and may  
cause injury to people and  
property. Remember the  
mixer's engine (gasoline  
models only) gives off  
DEADLY gases.  
■
■
NEVER operate this equipment when not feeling  
well due to fatigue, illness or taking medicine.  
■
■
ALWAYS refuel in a well-ventilated area, away from sparks  
NEVER operate this equipment under the  
influence or drugs or alcohol.  
and open flames.  
ALWAYS use extreme caution when working with flammable  
liquids. When refueling, stop the engine and allow it to cool.  
DO NOT smoke around or near the machine. Fire or explosion  
could result from fuel vapors, or if fuel is spilled on a hot  
engine.  
■
■
■
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
■
NEVER operate the mixer in an explosive  
atmosphere or near combustible  
materials. An explosion or fire could result  
causing severe bodily harm or even  
death.  
ALWAYS check the machine for loosened threads or bolts  
before starting.  
ALWAYS wear proper respiratory (mask) hearing and eye  
protection equipment when operating the mixer.  
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.  
Refer to the Engine Owner's Manual for engine technical  
questions or information.  
■
■
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
■
NEVER! place hands inside the drum while the drum is  
rotating.  
Manufacturer does not assume responsibility for any accident  
due to equipment modifications.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — RULES FOR SAFE OPERATION  
■
■
■
■
NEVER run engine without air cleaner.Severe engine damage  
■
NEVER disconnect any "emergency or safety devices".  
These devices are intended for operator safety. Disconnection  
of these devices can cause severe injury, bodily harm or even  
death! Disconnection of any of these devices will void all  
warranties.  
may occur.  
ALWAYS read, understand, and follow procedures in  
Operator’s Manual before attempting to operate equipment.  
ALWAYS be sure the operator is familiar with proper safety  
precautions and operations techniques before using roller.  
■
■
If mixer is equipped with an electric motor, operate electric  
motor only at the specified voltage indicated on the nameplate.  
ALWAYS store equipment properly when it is not being used.  
Equipment should be stored in a clean, dry location out of the  
reach of children.  
Make sure the OFF/ON power switch on the electric motor is  
always in the OFF position before inserting the mixer's power  
plug into an AC receptacle (electric model only).  
■
■
■
■
NEVER leave the mixer unattended, turn off engine or electric  
motor when unattended.  
Maintenance Safety  
■
NEVERlubricate components or attempt service on a running  
machine.  
CAUTION must always be observed while servicing this mixer.  
Rotating parts can cause injury if contacted.  
■
ALWAYS allow the machine a proper amount of time to cool  
before servicing.  
Unauthorized equipment modifications will void all  
warranties.  
■
■
Keep the machinery in proper running condition.  
Ensure that any extension cable is protected against damage  
and not liable to be tripped over or trapped underneath the  
mixer.  
Fix damage to the machine immediately and always replace  
broken parts, or missing decals.  
■
DO NOT allow extension cord to come into contact with water  
■
■
■
Dispose of hazardous waste properly.Examples of potentially  
hazardous waste are used motor oil, fuel and fuel filters.  
or fluids.  
■
■
DO NOT spray water onto electric motor.  
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
This mixer is intended for the production of concrete. Mixer  
must be used only for its intended purpose.  
DO NOT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
■
This mixer is not suitable for the mixing of flammable or  
explosive substances.  
Emergencies  
■
■
NEVER operate the mixer in an explosive atmosphere.  
■
ALWAYS know the location of the nearest fire extinguisher  
and first aid kit.  
Before starting the mixer, check that all guards are in position  
and correctly fitted.  
■
Keep area around the mixer clear of obstructions which  
could cause persons to fall onto moving parts.  
■
■
ALWAYS ensure mixer is on level ground before mixing.  
Become familiar with the controls of the mixer before  
operating.  
■
In emergencies always know the location of the  
nearest phone or keep a phone on the job site.  
Also know the phone numbers of the nearest  
ambulance, doctor and fire department. This  
information will be invaluable in the case of an  
emergency.  
■
■
ALWAYS replace any worn or damaged warning decals.  
Ensure the drum is rotating while filling and emptying the  
drum.  
■
■
ALWAYS disconnect AC power plug from power source  
before moving mixer (electric model only).  
High Temperatures – Always stop engine and allow the  
engine to cool before adding fuel, oil or performing service  
and maintenance functions. Contact with hot components  
can cause serious burns.  
PAGE 10 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — OPERATION AND SAFETY DECALS  
Machine Safety Decals  
The Multiquip MC-44S mixer is equipped with a number of safety decals (Figure 1A). These decals are provided for operator safety  
and maintenance information.The illustration below and on the next page shows these decals as they appear on the machine.  
Should any of these decals become unreadable, replacements can be obtained from your dealer.  
Figure 1A. MC-44S Mixer Decals  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — GENERAL INFORMATION  
Ensure that the extension cable is carefully laid out avoid-  
Application  
ing wet areas, sharp edges and locations where vehicles  
might run over it. Avoid allowing the extension cable to be  
trapped underneath the mixer.  
This mixer is only intended for the production of concrete.  
The mixer must be used for its intended purpose and is not  
suitable for the mixing of flammable or explosive  
substances. The mixer must not be used in an explosive  
atmosphere. Use Table 4 (Mixing Hints) as a guide when  
mixing concrete for various applications.  
Unroll the extension cable fully or it will overheat and could  
catch fire. Make sure that all extension cable connections  
are dry and safe. Replace any defective or badly worn ex-  
tension cable immediately.  
Power Plants  
The Multiquip MC42-S mixer can be powered by either a  
Honda GX120K1QX2 air-cooled, 4-stroke gasoline engine or  
a 1/2 HP electric motor.Refer toTable 2 to for specific engine  
or electric motor data information.  
Hardware  
Check all hardware on the mixer before starting. Periodically  
inspect all hardware. Loose hardware can contribute to early  
component failure and poor performance. UseTable 3 as general  
guideline when the torqueing of mixer hardware is required.  
Remember to keep all mixer hardware components tight.  
Electrical  
If mixer is equipped with an electric motor, make sure that  
the power being supplied to the motor corresponds to the  
voltage rating label on the motor.Supplying the wrong voltage  
to the electric motor will cause severe electrical damage to  
the motor.  
Table 3. Hardware Torque  
Recommendations  
Hardware  
Torque (ft-lbs)  
Diameter  
5/16-inch x 18  
3/8-inch x 16  
14  
24  
Always make sure the OFF/ON switch on the electric motor  
is in the OFF position before applying power.  
It is strongly recommended when inserting the mixer's  
power cord into a receptacle, that a G.F.C.I. (Ground Fault  
Current Interrupter) receptacle be used (115 VAC  
applications).  
3/8-inch x 24  
1/2-inch x 13  
37  
39  
90  
1/2-inch x 13  
(Grade 8)  
Extension Cables  
Engine Maintenance  
The extension cable should be a 3-wire configuration that  
includes a ground wire that conforms to UL code. The wire  
cross section must be a minimum of 2.5 mm2 . Choose an  
extension cord of adequate current carrying capacity as ref-  
erenced in Table 5. Remember distance affects the wire  
size of the extension cable.  
For basic engine maintenance, refer to the engine maintenance  
section in this manual. For a more detailed engine maintenance,  
refer to the Honda Engine Owner's manual furnished with the  
engine.  
Table 4. MIXING HINTS  
BATCH QUANTITIES  
SAND  
APPROX. BATCH  
OUTPUT  
MIX  
RATIOS  
CEMENT 112 lbs.  
(50 Kgs.)  
STONE  
CU. FT.  
APPLICATIONS  
Bag  
CU. FT.  
1-1/4  
LTR  
35  
LTR  
71  
CU. FT.  
3
LTR  
85  
1:2:4  
1:3:6  
1:4:8  
1/2 BAG  
1/3 BAG  
1/4 BAG  
2-1/2  
2-1/2  
2-1/2  
Most Ordinary  
Foundations  
1-1/4  
35  
71  
2-3/4  
2-3/4  
78  
1-1/4  
35  
71  
78  
Rough Mass  
Concrete  
1:1-1/2:3  
2/3 BAG  
1-1/4  
35  
3
71  
3
85  
Watertight Floors,  
Tanks, Pits, Etc.  
PAGE 12 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MIXER BASIC COMPONENTS  
Figure 2. Mixer Major Components  
1.  
Steel Mixing Drum — The Multiquip MC-44S concrete  
mixer uses a 4 cu. ft steel mixing drum.This drum is to be  
used for mixing of concrete. Always clean the drum after  
each use. DO NOT use this mixing drum for the mixing of  
volatile liquids.  
8.  
9.  
Rigid Suspension — This mixer uses a rigid type  
suspension. Check the mounting hardware for bolt hole  
elongation and tightness. See maintenance section of this  
manual for recommended maintenance.  
Chock Blocks — Place these blocks (not included as  
part of the mixer package) under each mixer wheel to  
prevent rolling, when mixer is not connect to the towing  
vehicle.  
2.  
3.  
Dump Latch —To rotate the mixing drum, this latch must  
be in the up position.To lock the drum, place the latch in the  
down position.  
10. Tires Ply — The tire ply (layers) number is rated in letters;  
This mixer uses 13-inch 2-ply tires. Replace with only  
recommended type tires.  
Dump Gear Guard — NEVER operate the mixer with this  
guard removed. Its purpose is to prevent dirt and debris  
from entering the dump gear. In addition operator clothing  
could become entangled in the dump gear, causing severe  
injury and bodily harm.  
11. ON/OFF Switch (gasoline only) —This switch is provided  
on mixer with gasoline engines only and is located on the  
side of the mixer frame. When activated it will shut down  
the engine. Pull out when starting the engine.  
4.  
5.  
Handwheel — Turn this wheel clockwise or counter-  
clockwise to rotate the mixing drum. Remember the dump  
latch must be in the up position in order for the mixing  
drum to be rotated.  
12. Cabinet/Latch — Encloses engine and electric motor.  
NEVER run mixer with cabinet removed. Use latches to  
secure engine compartment cabinet.  
Zerk Fittings — There is, at the bottom and engine side  
of the yoke, and center of the handwheel grease zerk  
fittings. Lubricate these fittings as referenced in the  
maintenance section of this manual.  
13. Mixing Blades (Steel) — Used for the mixing of concrete.  
When blades show signs of wear, entire steel mixing drum  
assembly must be replaced. See steel mixing drum  
assembly in the parts section of this manual.  
6.  
7.  
Safety Chain — This mixer uses a 3/16-inch thick, 72-  
inches long zinc-plated saftey chain.ALWAYS connect the  
safety chain when towing.  
14. Forklift Pockets – When lifting of the mixer is required,  
use these fork lift pockets to lift the mixer. Remember to  
insert the forks of the forklift a minimum of 24 inches into  
the lift pockets.  
Tow Bar — This mixer uses various towing bars, please  
reference the frame assembly drawing and parts list in this  
manual to determine which tow bar meets your  
requirements.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — BASIC ENGINE COMPONENTS  
Honda GX Series Engine Shown  
Figure 3. Engine Controls and Components  
INITIAL SERVICING  
5.  
FuelValve Lever – OPEN to let fuel flow, CLOSE to stop  
the flow of fuel.  
The engine (Figure 3) must be checked for proper lubrication and  
filled with fuel prior to operation. Refer to the manufacturers Engine  
manual for instructions & details of operation and servicing.  
6.  
Choke Lever – Used in the starting of a cold engine, or in  
cold weather conditions. The choke enriches the fuel  
mixture.  
7.  
Air Cleaner – Prevents dirt and other debris from entering  
the fuel system. Remove wing-nut on top of air filter  
cannister to gain access to filter element.  
1.  
Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tightened  
securely. DO NOT over fill.  
NOTE  
WARNING  
WARNING  
Operating the engine without an air filter,  
with a damaged air filter, or a filter in need of  
replacement will allow dirt to enter the  
engine, causing rapid engine wear.  
Adding fuel to the tank should be accomplished only  
when the engine is stopped and has had an  
opportunity to cool down. In the event of a fuel spill,  
8.  
Spark Plug – Provides spark to the ignition system. Set  
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). Clean  
spark plug once a week.  
DO NOT attempt to start the engine until the fuel residue has been  
completely wiped up, and the area surrounding the engine is dry.  
2.  
Throttle Lever – Used to adjust engine RPM speed (lever  
advanced forward SLOW, lever back toward operator  
FAST).  
9.  
Muffler – Used to reduce noise and emissions.  
WARNING  
3.  
Engine ON/OFF Switch – ON position permits engine  
starting, OFF position stops engine operations.  
Engine components can generate extreme heat.  
To prevent burns, DO NOT touch these areas  
4.  
Recoil Starter (pull rope) – Manual-starting method. Pull  
the starter grip until resistance is felt, then pull briskly and  
smoothly.  
while the engine is running or immediately after operating. NEVER  
operate the engine with the muffler removed.  
10. Fuel Tank – Holds unleaded gasoline. For additional  
information refer to engine owner's manual.  
PAGE 14 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — HANDWHEEL ASSEMBLY  
Assembly  
The Multiquip MC-44S concrete mixer is shipped with the  
handwheel detached. Attach the handwheel to the mixer as  
shown in Figure 4.  
Figure 4. Handwheel Assembly  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER —TOWING GUIDELINES  
■
■
■
■
Check wheel mounting lug nuts with a torque wrench.  
Torque wheel lug nuts as described in the maintenance  
section of this manual.  
Towing Safety Precautions  
CAUTION:  
Check tightness of U-clamp nuts, torque suspension  
hardware as referenced in the maintenance section of this  
manual.  
■
Check with your county or state safety  
towing regulations department before  
towing your mixer.  
Avoid sudden stops and starts.This can cause skidding, or  
jackknifing. Smooth, gradual starts and stops will improve  
gas milage.  
To reduce the possibility of an accident while transporting  
the mixer on public roads, always make sure that the mixer  
towing components and the towing vehicle are in good  
operating condition and both units are mechanically sound.  
Avoid sharp turns to prevent rolling.  
CAUTION:  
The following list of suggestions should be used when towing  
the mixer:  
If the mixer tow bar is deformed or damaged  
replace entire tow bar. NEVER tow the mixer  
with a defective tow bar. There exist the  
possibility of the trailer separating from the  
towing vehicle.  
■
Make sure that the hitch and coupling of the towing vehicle  
are rated equal to, or greater than the trailer "gross vehicle  
weight rating" (GVWR).  
■
■
■
■
■
■
ALWAYS inspect the hitch and coupling for wear. NEVER  
tow the mixer with defective hitches, couplings, chains etc.  
Tow Bar to Vehicle Connection (Coupler Only)  
1. Check the vehicle hitch ball, and mixer's coupler for  
signs of wear or damage. Replace any parts that are  
worn or damaged before towing.  
CHECK the tire air pressure on both the towing vehicle and  
the trailer.Also check the tire tread wear on both vehicles.  
ALWAYS make sure the mixer is equipped with a "Safety  
Chain".  
2. Use only a 2-inch ball diameter (towing vehicle), this  
will match the mixer's 2-inch coupler. Use of any other  
ball diameter will create an extremely dangerous condition  
which can result in separation of the coupler and ball or  
ball failure.  
ALWAYS attach trailer's safety chain to the frame of towing  
vehicle.  
ALWAYS make sure that the towing vehicle's directional,  
backup, and brake lights are working properly.  
3. After tow bar has been connected to mixer (see next  
page), attach mixer's coupler to the hitch ball on the  
towing vehicle securely and make sure the lock lever  
is in the down position (locked).  
Remember in most cases the maximum speed unless  
otherwise posted for highway towing is 45 MPH, however  
before towing your mixer, check your local state, and county  
vehicle towing requirements. Recommended off-road towing  
is not to exceed 10 MPH or less depending on type of terrain.  
■
■
■
■
Place chocked blocks underneath wheels to prevent rolling,  
while parked, if disconnected from towing vehicle.  
Mixer Tow Bar Vehicle Connection (Pintle and Loop)  
1. Make sure the bumper on the towing vehicle is  
equipped to handle either a pintle or loop type tow  
bar configuration.  
Inflate tires to correct pressure, inspect tires for cuts, and  
excessive wear.See Table 16 (Tire Wear Troubleshooting).  
When towing of the mixer is required, place the drum in the  
up position (mouth facing upwards).  
2. After tow bar has been connected to mixer (see next  
page), secure either type of tow bar to the towing vehicle,  
following state and county towing regulations.  
ALWAYS make sure that the fuel valve lever is in the OFF  
position (gasoline models only).  
3. As a minimum, use a 1/2-inch bolt and nylock nut grade  
5 when securing either tow bar to the towing vehicle,  
PAGE 16 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — SAFETY CHAIN CONNECTION  
2. Route the safety chain through the holes just above the  
tow bar, located on each side of the mixer stand.  
CAUTION:  
NEVER ! tow the mixer with the safety chain  
removed. The safety chain is intended to  
prevent complete separation of the mixer from  
the towing vehicle in the event of a tow bar  
failure.  
Loop the chain together and place under the tow bar.  
Secure the loop with the connector link.  
3. Extend the safety chain along the length of the tow bar,  
looping it through the tow bar's connector link. Remove  
any excess chain slack.  
Reference Figure 5 for the installation of the Safety Chain.  
4. Connect the free end of (clevis safety hook) the safety  
chain to the towing vehicle. Remember it is critical  
that the length of the chain be properly adjusted, to  
prevent the draw bar and the front of the mixer stand  
from dropping to the the ground (contact) in the event  
the draw bar becomes disconnected from the towing  
vehicle.  
Tow Bar to Mixer Connection  
1. Insert the tow bar through the round opening at the  
bottom of the mixer stand.  
Align the hole on the tow bar with the hole on the mixer  
frame, and insert 1/2-inch bolt through tow bar and frame.  
Secure tow bar to frame with 1/2-inch nylock nut.Tighten  
to 40 ft.-lbs.  
Figure 5. Tow Bar and Safety Chain Installation  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — ELECTRIC MOTOR  
Electric Motor  
Table 5. Recommended Extension Cord Sizes  
For maintenance care and operation of the electric motor, refer  
to your electric motor instruction booklet furnished with the electric  
motor.  
Electric  
Motor  
Input  
Voltage  
50 ft.  
(15.24 m)  
75 ft.  
100 ft.  
200 ft.  
(22.86 m) (30.48 m) (60.96 m)  
Protect the electric motor from dust as much as possible and  
keep ventilating openings clean.  
1/2 HP  
115 VAC  
No. 12  
No. 10  
No. 8  
No. 6  
CAUTION:  
■
■
DO NOT spray water at any time on the  
electric motor.  
Electric MotorVoltage Change Switch  
DO NOT operate electric motor in a  
explosive environment.  
1.  
ALWAYS make certain the electric motor's ON/OFF switch  
is in the "OFF" position and the power cord has been  
disconnected from the power source.  
The electric motor used in this mixer is a single-phase 1.5 HP  
motor. The input voltage requirement for this motor is either 115  
or 230VAC only.  
Electric Motor Connection  
NEVER! disable or disconnect the  
ON/OFF switch on the electric motor.  
A 12 inch electrical cable (Figure 2) with a pigtail at one end is  
provided with the electrical motor for hookup to a power source.  
Table 1. shows the required NEMA connector for the desired  
motor horsepower rating. In addition, Table 2 also shows the  
matching NEMA approved connector for the required extension  
cord.  
It is provided for operator safety.Injury  
may result if it is disable, disconnected  
or improperly maintained.  
ALWAYS, make certain that the power source required for the  
electric motor is correct and always use the correct NEMA  
configuration plug. Failure to supply the correct voltage to the  
motor can severely damage the motor.  
The electric motor supplied with the mixer is configured from the  
factoryfor115VACgroundedoperation.Makecertainthatthecorrect  
size grounded (3-wires) extension cord is used.SeeTable 5.  
Motors can burn out when the line voltage falls 10% below the  
voltage rating of the motor. Failure to use proper voltage will  
cause the motor to overheat and actuate the overload switch.  
If overload protection should actuate because of improper voltage  
or any other malfunction, turn the main switch on the motor to the  
"OFF" position and correct the problem, press the reset switch  
button, and turn the main switch to the "ON" position.  
PAGE 18 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — ELECTRIC MOTOR  
Figure 6. Single Phase Electric Motor with 12 inch Pigtail Cable  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — PRE-INSPECTION (GAS ENGINE)  
Before Starting  
Table 6. Oil Type  
1. Read safety instructions at the beginning of manual.  
Season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C~10°C  
Oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
2. Clean the mixer, removing dirt and dust, particularly the  
engine cooling air inlet, carburetor and air cleaner.  
3. Check theairfilterfor dirtanddust. Ifairfilterisdirty,replace  
air filter with a new one as required.  
0°C or Lower  
4. Check carburetor for external dirt and dust. Clean with dry  
compressedair.  
Explosive Fuel  
5. Checkfasteningnutsandboltsfortightness.  
Fuel Check  
Engine Oil Check  
If your mixer has a gasoline engine, determine if the engine fuel  
is low. If fuel is low, remove the fuel filler cap and fill with unleaded  
gasoline. Motor fuels are highly flammable and can be dangerous  
if mishandled. DO NOT smoke while refueling. DO NOT attempt  
to refuel the trowel if the engine is hot! or running.  
1. To check the engine oil level, place the mixer on  
secure level ground with the engine stopped.  
2. Remove the filler dipstick from the engine oil filler hole  
(Figure 7) and wipe it clean.  
1. Remove the gasoline cap located on top of fuel tank.  
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish  
with unleaded fuel.  
3. When refueling, be sure to use a strainer for filtration. DO  
NOT top-off fuel. Wipe up any spilled fuel.  
V-belt Check  
A worn or damagedV-belt can adversely affect the performance  
of the mixer.If aV-belt is defective or worn simply replace theV-  
belt as outlined in the maintenance section of this manual.  
Figure 7. Engine Oil Dipstick (Removal)  
Blade Check  
3. Insert and remove the dipstick without screwing it into the  
filler neck. Check the oil level shown on the dipstick.  
Check for worn blades. If using a steel tub and the blades are  
worn, replace the entire tub assembly. Remember the blades  
are welded to tub.  
4. If the engine oil level is low (Figure 8), fill to the edge of  
the oil filler hole with the recommended oil type (Table 6).  
See Table 2 for the oil capacity of your type engine.  
If using a plastic tub, replace the blades using the part numbers  
referenced in the parts section of this manual.  
Start/Stop Switches  
This mixer has been equipped with a start/stop switches for both  
the gasoline and electric motor mixers.These switches should be  
tested every time the engine or motor is started.  
Grease Fittings (Zerk)  
Check the zerk grease fittings (Figure 26) as shown in the  
maintenancesectionofthismanual.Thesegreasefittingslubricate  
the handwheel and the yoke mechanism.  
Figure 8. Engine Oil Dipstick (Oil Level)  
PAGE 20 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — INITIAL START-UP (GAS ENGINE)  
Starting the Engine (Gasoline Only)  
4.  
Turn the engine switch (Figure 12) to the ON position.  
The following steps outline the procedure for starting the engine.  
Depending on the type of engine employed in the mixer the  
steps may vary slightly. If your mixer has an electric motor  
disregard this section.  
1.  
Move the fuel shut-off lever (Figure 9) to the ON position.  
Figure 12. Engine ON/OFF Switch  
5.  
Located at the rear of the mixer frame is the main start/  
stop button (Figure 13). Pull this button outward to start the  
engine.  
Figure 9. Fuel Shut-OFF Lever  
2.  
To start a cold engine, move the choke lever (Figure 10) to  
the CLOSED position.  
Figure 13. Engine Start/Stop Button  
6.  
Pull the starter grip (Figure 14) lightly until you feel  
resistance, then pull briskly.The drum should be rotating at  
this time.  
Figure 11. Choke Lever  
3.  
Move the throttle lever (Figure 11) away from the slow  
position, about 1/3 of the way toward the fast position.  
Figure 14. Starter Grip  
Figure 11. Throttle Lever  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — INITIAL START-UP (ELECTRIC MOTOR)  
5. Plug the other end of the extension cord into a 120 VAC  
G.F.C.I.protected receptacle. Rememberthepowerrequire-  
ments for this electric motor is 120VAC, 60 Hz. The use of  
any other input voltage will severely damage the motor.  
Initial Start-up Instructions (Electric Motor)  
Starting  
CAUTION:  
DO NOT attempt to operate the mixer until  
CAUTION:  
the Safety, General Information and  
Inspection sections have been read and  
understood.  
ALWAYS read the label on the electric motor  
before applying power.The label will indicate  
the proper power requirements for the motor.  
Remember the use of any other input voltage  
will severely damage the motor.  
1. Before starting, make sure mixer is positioned on a secure  
flat surface to prevent rolling.  
CAUTION:  
2. Use an extension cord (see Table 5) of adequate current  
carryingcapacity,insert theelectricmotor'spowerplug into  
one end of the extension cord.  
To prevent tripping (Figure 16) of personnel,  
position the extension cord so that it lays flat  
and is not curled underneath the mixer.  
3. NEVER! use a worn or frayed extension cord.  
4. NEVER! operate mixer withV-belt cover removed.  
DANGER  
NEVER! touch the power cord (Figure 15)  
with wet hands or while standing in water  
when it is connected to a power source.The  
possibly exists of electrical shock  
(electrocution) even death. NEVER! spray  
water directly on the electric motor.  
Figure 16. Extension Cord (Tripping)  
WARNING:  
ALWAYS read the label on the electric motor  
before applying power.The label will indicate  
the correct power requirements for the motor.  
Remember the use of an incorrect input  
voltage will severely damage the electric  
motor.  
Figure 15. Extension Cord (Wet Hands)  
Starting the Electric Motor  
1.  
Set the electric motor's ON/OFF switch (Figure 17) to the  
ON position.  
To prevent personnel from tripping over  
the extension cord, position the  
NOTE  
extension cord so that it lays flat and is  
not curled underneath the mixer.  
Figure 17. Electric Motor ON/OFF Switch  
(ON Position)  
PAGE 22 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — OPERATION  
3. Placingtheshovelallthewayinsidethedrum(Figure20)will  
causetheshoveltostriketheblades.Thisconditionwillmake  
Operation  
1. Topositionthetub,makesurethemixerisplacedonfirmlevel  
ground,thenpulluponthedumplatch (Figure18)andturn  
thehandwheeluntilthetubisatthedesiredposition.Once  
thetubisatthedesiredposition,pulldownonthedumplatch  
to lock the tub in position.  
the shovel rotate, and could cause injury to personnel.  
NEVER place hands inside the mixing drum while it is  
rotating.  
Figure 20. Filling Mixing Drum  
Stopping the Mixer (Gasoline)  
1.  
Push the main start/stop switch (Figure 21) inward to stop  
the engine.  
Figure 18. Mixing Drum Positioning  
CAUTION:  
NEVER stand in front or behind the mixing  
drum while it is being placed in the dump  
position. Stay clear of the mixing drum while  
it is being positioned.  
Figure 21. Start/Stop Button (Stop Position)  
2.  
3.  
Place fuel shut-off lever in the OFF position.  
2. As the drum rotates, use a shovel (Figure 19) to place the  
cementmixinsidethedrum,addwaterasrequired.Becareful  
to only place the tip of the shovel inside the drum.  
Clean drum of all debris and foreign matter.  
Stopping the Mixer (Electric)  
1.  
Place the electric motor's ON/OFF switch (Figure 22) in  
the OFF position.  
Figure 22. Electric Motor ON/OFF Switch  
(OFF Position)  
2.  
3.  
Disconnect the electric motor's extension cord from its  
power source.  
Figure 19. Filling Mixing Drum  
Clean drum of all debris and foreign matter.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MAINTENANCE (ENGINE)  
UseTable 7 as a general maintenance guideline when servicing  
your engine. For more detail engine maintenance information,  
refer to the engine owner's manual supplied with your engine.  
Table 7. Engine Maintenance Schedule  
FIRST  
EVERY  
EVERY  
EVERY  
YEAR  
OR  
EVERY  
2 YEARS  
OR  
MONTH 3 MONTHS 6 MONTHS  
OR  
DESCRIPTION (3)  
OPERATION  
BEFORE  
OR  
OR  
10 HRS.  
25 HRS.  
50 HRS.  
100 HRS.  
200 HRS.  
CHECK  
CHANGE  
CHECK  
X
Engine Oil  
X
X
X
Air Cleaner  
All Nuts & Bolts  
Spark Plug  
CHANGE  
X (1)  
Re-tighten If  
Necessary  
CHECK-CLEAN  
REPLACE  
CHECK  
X
X
X
Cooling Fins  
Spark Arrester  
Fuel Tank  
CLEAN  
X
X
CLEAN  
Fuel Filter  
CHECK  
X
Idle Speed  
CHECK-ADJUST  
CHECK-ADJUST  
CHECK  
X (2)  
Valve Clearance  
Fuel lines  
X (2)  
Every 2 years (replace if necessary) (2)  
(1) Service more frequently when used in DUSTY areas.  
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically  
proficient. Refer to the HONDA or ROBIN Shop Manual for service procedures.  
(3) For commercial use, log hours of operation to determine proper maintenance intervals.  
PAGE 24 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MAINTENANCE (ENGINE)  
DANGER :  
Maintenance  
Perform the scheduled maintenance procedures as defined by  
Table 6 and below:  
DO NOT use gasoline as a cleaning solvent,  
because that would create a risk of fire or  
explosion.  
DAILY  
■
Thoroughly remove dirt and oil from the engine and control  
area.Clean or replace the air cleaner elements as necessary.  
Check and retighten all fasteners as necessary. Check the  
gearbox for oil leaks. Repair or replace as needed.  
ENGINEAIRCLEANER  
WEEKLY  
1. Remove the air cleaner cover and foam filter element as  
shown in Figure 25.  
■
Remove the fuel filter cap and clean the inside of the fuel  
tank.  
2. Tap the paper filter element (Figure 34) several times on a  
hard surface to remove dirt, or blow compressed air [not  
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter  
elementfromtheaircleanercaseside.NEVER brushoffdirt.  
Brushingwillforcedirtintothefibers.Replacethepaperfilter  
element if it is excessively dirty.  
■
■
Remove or clean the filter at the bottom of the tank.  
Remove and clean the spark plug (Figure 23), then adjust  
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm).This unit  
has electronic ignition, which requires no adjustments.  
3. Cleanfoamelementinwarm,soapywaterornonflammable  
solvent. Rinseanddrythoroughly. Diptheelementinclean  
engineoilandcompletelysqueezeouttheexcessoilfromthe  
element before installing.  
Figure 23. Spark Plug Gap  
ENGINEOIL  
1. Drain the engine oil when the oil is warm as shown in  
Figure 24.  
2. Remove the oil drain bolt and sealing washer and allow  
the oil to drain into a suitable container.  
3. Replace engine oil with recommended type oil as listed  
in Table 6. For engine oil capacity, see Table 2 (engine  
specifications). DO NOT overfill.  
4. Install drain bolt with sealing washer and tighten se-  
curely.  
Figure 25. Engine Air Cleaner  
Figure 24. Engine Oil (Draining)  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MAINTENANCE (MIXER)  
2.  
Use Poleyrex EM (Exxon Mobil) or equalivant lubricant.  
Clean grease fitting, apply grease gun to fitting (1/2 shot).  
Remember too much grease or injecting grease too quickly  
can cause premature bearing failure. Slowly apply the  
recommended amount of grease, taking a miniute or so to  
apply.  
Ball Socket and Clamp Face Maintenance  
1.  
If the towing vechicle is equipped with a ball socket, smear  
socket periodically with multi-purpose grease. This will keep  
the ball socket well lubricated.  
2.  
3.  
Periodically oil pivot points and clamp face surfaces of  
coupler with SAE 30 WT. motor oil.  
Wheel Bearings  
1. After every 3 months of operation, remove the hub dust cap  
When parking or storing your mixer. Keep the coupler off  
the ground so dirt will not build up in the ball socket.  
and inspect the wheel bearings (Figure 28).Once a year,  
or when required, disassemble the wheel hubs remove  
the old grease and repack the bearings forcing grease  
between rollers, cone and cage with a good grade of high  
speed wheel bearing grease (never use grease heavier  
than 265 A.S.T.M. penetration (“No. 2.”)  
Grease Fittings (Zerk) Maintenance (Mixer)  
There are 3 grease (Figure 26) fittings that will require  
lubrication. Lubricate these fittings once a week. Use lithium  
base grease, grade N0.1.  
Figure 28. Wheel Hub and Bearings  
Figure 26. Grease Fittings Mixer  
2.  
Fill the wheel hub (Figure 28) with grease to the inside  
diameter of the outer races and also fill the hub grease cap.  
Reassemble the hub and mount the wheel. Then tighten  
the adjusting nut, at the same time turn the wheel in both  
directions, until there is a slight bind to be sure all the  
bearing surfaces are in contact.  
Grease Fittings (Zerk) Maintenance (Electric Motor)  
1.  
There are two grease (Figure 27) fittings at each end of the  
electric motor that will require lubrication. Lubricate these  
fittings about every 16 months.  
Then back-off the adjusting nut 1/6 to 1/4 turn or to the  
nearest locking hole or sufficiently to allow the wheel to  
rotate freely within limits of .001" to .010" end play.Lock the  
nut at this position. Install the cotter pin and dust cap, and  
tighten all hardware.  
Mixer Cleaning  
1.  
For thorough mix and longer drum life, always wash drum  
out after each use.  
2.  
NEVER! pour or spray water over the engine or electric  
motor.  
Figure 27. Grease Fittings Electric Motor  
PAGE 26 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MAINTENANCE (MIXER)  
Tires/Wheels/Lug Nuts  
Tires and wheels are a very important and critical compo-  
nents of the trailer. When specifying or replacing the trailer  
wheels it is important the wheels, tires, and axle are prop-  
erly matched.  
CAUTION:  
DO NOT attempt to repair or modify a  
wheel. DO NOT install an inter-tube to  
correct a leak  
through the rim.  
If the rim is cracked, the air  
pressure in the inter-tube may  
cause pieces of the rim to explode  
(break-off) with great force and  
can cause serious eye or bodily  
injury.  
Suspension  
The rigid suspension and associated components (Figure  
29) should be visually inspected every 6,000 miles for signs  
of excessive wear, elongation of bolt holes, and loosening  
of mounting bracket. Replace any damaged suspension  
component immediately.  
TiresWear/Inflation  
Tire inflation pressure is the most important factor in tire  
life. Pressure should be checked cold before operation. DO  
NOT bleed air from tires when they are hot. Check inflation  
pressure weekly during use to insure the maximum tire life  
and tread wear.  
Table 8 (Tire Wear Troubleshooting) will help pinpoint the  
causes and solutions of tire wear problems.  
CAUTION:  
ALWAYS wear safety glasses when  
removing or installing force fitted  
parts. Failure to comply may result  
in serious injury.  
Figure 29. Suspension Components  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — MAINTENANCE (MIXER)  
Lug NutTorque Requirements  
It is extremely important to apply and maintain proper wheel  
mounting torque on the trailer. Be sure to use only the fas-  
teners matched to the cone angle of the wheel. Proper pro-  
cedure for attachment of the wheels is as follows:  
1. Start all wheel lug nuts by hand.  
2. Torque all lug nuts in sequence. See Figure 30. DO NOT  
torquethewheellugnutsallthewaydown.Tighteneachlug  
nut in 3 separate passes as defined by Table 9.  
3. Afterfirstroaduse,retorquealllugnutsinsequence.Check  
all wheel lug nuts periodically.  
NEVER! use an pneumatic air gun  
to tighten wheel lug nuts.  
Mixer Storage  
For storage of the mixer for over 30 days, the following is  
recommended:  
Drain the fuel tank completely, or add STA-BIL to the  
fuel.  
Run the engine until the fuel is completely consumed.  
Completely drain used oil from the engine crankcase  
and fill with fresh clean oil, then follow the procedures  
described in the engine manual for engine storage.  
Clean the entire mixer and engine compartment.  
Place the mixing drum in the down position (mouth facing  
downward).  
Cover the mixer and place it a clean dry area, that is  
protected from harsh elements.  
Figure 30. Wheel Lug Nuts Tightening Sequence  
PAGE 28 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — TROUBLESHOOTING (ENGINE)  
diagnosis based on the Troubleshooting (Tables 9 and 10)  
information shown below and on the next page. If the problem  
cannot be remedied, please leave the unit just as it is and  
consult our company's business office or service plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 9. ENGINE TROUBLESHOOTING  
SYMPTOM  
Difficult to start  
POSSIBLE PROBLEM  
SOLUTION  
Ignition plug being bridge?  
Carbon deposit at ignition?  
Check ignition system.  
Clean or replace ignition.  
Replace insulators.  
Fuel is available but spark plug  
will not ignite. (Power available  
at high tension cable).  
Short circuit due to defective  
insulators?  
Improper spark gap?  
Set spark plug gap to the correct gap.  
Check stop switch circuit. Replace stop switch if defective.  
Replace ignition coil.  
Short circuit at stop switch?  
Ignition coil defective?  
Fuel is available but spark plug  
will not ignite. (Power NOT  
available at high tension cable).  
Muffler clogged with carbon  
deposits?  
Clean or replace muffler.  
Fuel is available and spark plug  
ignites (compression normal).  
Fuel in use inadequate (water,  
dust)?  
Flush fuel sytem and replace with fresh fuel.  
Air Cleaner clogged?  
Defective cylinder head gasket?  
Cylinder worn?  
Clean or replace air cleaner.  
Tighten cylinder head bolts or replace head gasket.  
Replace cylinder.  
Fuel is available and spark plug  
ignites (compression low ).  
Spark plug loose?  
Tighen spark plug.  
Operation not satisfactory  
Air cleaner clogged?  
Air in fuel line?  
Bleed (remove air) from fuel line.  
Adjust carbureator float  
Not enough power available  
(compression normal, no miss-  
firing).  
Fuel level in carbureator float  
chamber improper?  
Carbon deposits in cylinder?  
Ignition coil defective?  
Clean or replace cylinder  
Flush fuel sytem and replace with fresh fuel.  
Replace ignition wires, clean ignition.  
Flush fuel sytem and replace with fresh fuel.  
Not enough power available  
(compression normal, miss-  
firing).  
Ignition plug often shorts?  
Fuel in use inadequate (water,  
dust)?  
Excessive carbon depostion in  
combustion chamber?  
Clean or replace crankcase.  
Clean or replace muffler.  
Engine overheats.  
Exhaust or muffler clogged with  
carbon.  
Spark plug heat value incorrect? Replace spark plug with correct type spark plug.  
PAGE 30 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — TROUBLESHOOTING (ENGINE/MIXER)  
TABLE 9. ENGINE TROUBLESHOOTING (Continued)  
SYMPTOM  
POSSIBLE PROBLEM  
SOLUTION  
Operation not satisfactory  
Governor adjustment improper?  
Governor spring defective?  
Fuel flow erratic?  
Adjust governor to correct lever.  
Clean or replace ignition.  
Check fuel line.  
Rotational speed fluctuates.  
Air taken in through suction  
line?  
Check suction line.  
Dust in rotating part?  
Spring spring failure?  
Clean recoil starter assembly.  
Replace sprial spring.  
Recoil starter not working  
properly.  
TABLE 10. MIXER TROUBLESHOOTING  
SYMPTOM  
POSSIBLE PROBLEM  
SOLUTION  
Check that the ring gear and bearings are not worn . Replace as  
necessary.  
Defective ring gear?  
Check that the pinion gear and bearings are not worn . Replace as  
necessary.  
Defective pinion gear?  
Drum rotates rough.  
Worn V-belt?  
Loose pulley?  
Replace V-belt.  
Tighten or replace pulley.  
Incorrect or no voltage being  
supplied to electric motor?  
Check that the electric motor has the correct supply voltage.  
Inspect power source and extension cord. Push reset button on  
electric motor. Make sure correct voltage is being supplied to motor.  
Power to electric motor?  
Fuel?  
Check level of fuel in fuel tank. Add fuel if necessary. Make sure  
fuel is being supplied to the engine. Check to ensure that the fuel  
filter is not clogged.  
Drum does not rotate at all.  
Broken V-belt?  
Replace V-belt.  
Check that the gears and bearings are not broken. Replace as  
necessary.  
Defective ring or pinion gears?  
Defective electric motor?  
Replace electric motor.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLANATION OF CODE IN REMARKS COLUMN  
The following section explains the different symbols and  
QTY. Column  
remarks used in the Parts section of this manual. Use the  
help numbers found on the back page of the manual if there  
are any questions.  
Numbers Used — Item quantity can be indicated by a  
number, a blank entry, or A/R.  
A/R (As Required) is generally used for hoses or other  
parts that are sold in bulk and cut to length.  
NOTICE  
The contents and part numbers listed in the parts  
section are subject to change without notice.Multiquip  
does not guarantee the availability of the parts listed.  
A blank entry generally indicates that the item is not sold  
separately.Other entries will be clarified in the“Remarks”  
Column.  
SAMPLE PARTS LIST  
REMARKS Column  
NO. PART NO. PART NAME  
QTY. REMARKS  
Some of the most common notes found in the “Remarks”  
Column are listed below. Other additional notes needed  
to describe the item can also be shown.  
1
2%  
12345  
BOLT......................1 .....INCLUDES ITEMS W/%  
WASHER, 1/4 IN............NOT SOLD SEPARATELY  
WASHER, 3/8 IN....1 .....MQ-45T ONLY  
2% 12347  
3
4
12348  
12349  
HOSE ..................A/R ...MAKE LOCALLY  
BEARING ..............1 .....S/N 2345B AND ABOVE  
Assembly/Kit — All items on the parts list with the  
same unique symbol will be included when this item is  
purchased.  
NO. Column  
Indicated by:  
Unique Symbols — All items with same unique  
symbol  
“INCLUDES ITEMS W/(unique symbol)”  
(@, #, +, %, or >) in the number column belong to the  
same assembly or kit, which is indicated by a note in the  
“Remarks” column.  
Serial Number Break — Used to list an effective serial  
number range where a particular part is used.  
Indicated by:  
Duplicate Item Numbers — Duplicate numbers indicate  
multiple part numbers, which are in effect for the same  
general item, such as different size saw blade guards in  
use or a part that has been updated on newer versions  
of the same machine.  
“S/N XXXXX AND BELOW”  
“S/N XXXX AND ABOVE”  
“S/N XXXX TO S/N XXX”  
Specific Model Number Use — Indicates that the part  
is used only with the specific model number or model  
number variant listed. It can also be used to show a  
part is NOT used on a specific model or model number  
variant.  
NOTICE  
When ordering a part that has more than one item  
number listed, check the remarks column for help in  
determining the proper part to order.  
Indicated by:  
“XXXXX ONLY”  
“NOT USED ON XXXX”  
PART NO. Column  
Numbers Used — Part numbers can be indicated by a  
number, a blank entry, or TBD.  
“Make/Obtain Locally” — Indicates that the part can  
be purchased at any hardware shop or made out of  
available items.Examples include battery cables, shims,  
and certain washers and nuts.  
TBD (To Be Determined) is generally used to show a  
part that has not been assigned a formal part number  
at the time of publication.  
“Not Sold Separately”— Indicates that an item cannot  
be purchased as a separate item and is either part of an  
assembly/kit that can be purchased, or is not available  
for sale through Multiquip.  
A blank entry generally indicates that the item is not sold  
separately or is not sold by Multiquip. Other entries will  
be clarified in the “Remarks” Column.  
PAGE 32 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — SUGGESTED SPARE PARTS  
MC-44S CONCRETE MIXER 1TO 4 UNITSWITH  
HONDA GX120K1QX2 ENGINE  
Qty. P/N  
Description  
2 ....... 507725 ................ V-BELT w/GAS ENGINE  
1 ....... 29173-001 ........... STOP BUTTON w/GAS ENGINE  
2 ....... 491010 ................ LATCH SET  
1 ....... 500904 ................ EXPANSION PLUG  
2 ....... EM903017 ........... SPINDLE BEARING CUP  
2 ....... EM903054 ........... SPINDLE BEARING CONES  
1 ....... EM505472 ........... SPACER, DRUM  
2 ....... 041006204 .......... BEARING, JACKSHAFT  
2 ....... EM914288 ........... SEAL, AXLE  
2 ....... EM903012 ........... BEARING CUP  
2 ....... EM903113 ........... BEARING CONE  
2 ....... 3469 .................... DUST CAP, AXLE  
4 ....... 17210ZE0505 ...... ELEMENT, AIR CLEANER  
4 ....... 9807955846......... SPARK PLUG  
1 ....... 17620ZH7023...... CAP, FUEL TANK  
1 ....... 28462ZH8003...... ROPE, RECOIL STARTER  
Part numbers on this Suggested  
Spare Parts List may supercede/  
replace the P/N's shown in the  
test pages of this manual.  
NOTE  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER — NAME PLATE AND DECALS  
NAME PLATE AND DECALS  
PAGE 34 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S CONCRETE MIXER— NAME PLATE AND DECALS  
NAME PLATE AND DECALS  
NO  
1
2
3
4
5
6
7
PART NO  
512910  
CIPDCL160  
504713  
EM948630  
DCL151  
35137  
PART NAME  
MQ MULTIQUIP LOGO  
QTY.  
REMARKS  
3
2
1
1
1
1
1
DECAL, CRUSHWARNING  
DECAL, SAFETY INSTRUCTIONS  
DECAL, EMERGENCY STOP  
DECAL, TOWING INSTRUCTIONS  
DECAL, READ  
13118  
DECAL, POWDER COATED  
8
NAMEPLATE........................................................ 1 ......... CONTACT MQ PARTS DEPT.  
SEE OPERATION AND SAFETY DECALS PAGE.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — STEEL BARREL ASSY.  
STEEL BARREL ASSY.  
PAGE 36 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — STEEL BARREL ASSY.  
STEEL BARREL ASSY.  
NO  
1
2
PART NO  
500904  
501867  
PART NAME  
CAP  
KING PIN  
QTY.  
1
1
REMARK  
3
4
5
6
7
8
8
8
EM903054  
EM903017  
504096  
EM963610  
501061  
511732  
511731  
511730  
EM969013  
490952  
502019  
493296  
EM963692  
492584  
514672  
491008  
EM916001  
500214  
501917  
492467  
EM505472  
492483  
500601  
SPINDLE BEARING 5/8" CONE ............ 2 ............. REPLACES 492154  
SPINDLE BEARING CUP ...................... 2 ............. REPLACES 492233  
RING GEAR  
1
6
1
AR  
AR  
AR  
5
BOLT 3/8" NC 1-1/4" G5  
BARREL, STEEL 4 CU. FT.  
SHIM 0.25 THICK  
SHIM .187 THICK  
SHIM .140 THICK  
9
NUT, LOCK 3/8” NC  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
RING, RETENTION  
2
1
2
2
2
1
3
DRIVE PINION SHAFT  
PINION SHAFT BEARING  
BOLT 1/2" NC X 1-1/2" G5  
LOCKNUT, HEX 1/2" NC  
HOUSING JACKSHAFT  
CAP, GREASE FITTING  
GREASE FITTING 1/8" NPT ................. 3.............. REPLACES 491698  
SQUARE KEY 1/4" X 30 MM  
DRIVE PINION  
ALLEN SCREW 5/16 NC 3/8"  
SPACER, BARREL  
SET SCREW 3/8" X 1- 1/4" NC  
1
1
1
1
1
NUT, HEX LOWER 1" ............................ 1 ............. REPLACES 492579  
492406  
492584  
510736  
491685  
500601  
501269  
BOLT 5/8" NC X 1-1/2" NC  
LOCKNUT, HEX 1/2" NC  
YOKE  
COTTER PIN 3/32" X 2"  
CASTLE NUT 1"  
SPACER  
2
2
1
1
1
1
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — MAIN FRAME ASSY.  
MAIN FRAME ASSY.  
PAGE 38 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — MAIN FRAME ASSY.  
MAIN FRAME ASSY.  
NO  
1
2
PART NO  
501844  
2101402  
PART NAME  
GUARD, GEAR WHEEL  
WASHER, LOCK 1/4"  
QTY.  
1
4
REMARK  
3
4
5
6
7
8
492284  
502017  
EM969013  
490896  
EM963610  
491008  
ROUND HEAD BOLT 1/4" NC 3/8 G2" ......... 4.............. REPLACES 492279  
DUMP GEAR  
1
1
1
1
2
NUT, LOCK 3/8" NC  
DUMP LATCH  
BOLT 3/8" NC X 1-1/2" G5  
GREASE CAP  
9
EM916001  
EM963055  
3103160  
495595  
514643  
10176  
EM124  
500596  
501902  
GREASE FITTING 1/8" NPT ........................ 2.............. REPLACES 491698  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
19  
19A  
20  
ALLEN BOLT 3/16" NS X 5/8"  
WASHER, LOCK 3/16"  
WASHER, FLAT 3/16"  
FRAME  
4
4
4
1
LOCK NUT 1/2 NC........................................ 1.............. REPLACES 492586  
BOLT 1/2"- 13 X 4 G5  
HANDWHEEL SHAFT  
HANDWHEEL  
1
1
1
1
SAFETY CHAIN  
*
01004  
01004  
516580  
490958  
13363KIT  
HBC-1  
HLC-1  
CONNECTOR LINK ...................................... 2 .............. BEFORE JANUARY 2006  
CONNECTOR LINK ...................................... 1 .............. AFTER JANUARY 2006  
CLEVIS SAFETY HOOK, 1/4" ..................... 1 .............. AFTER JANUARY 2006  
*
*
*
RING RETAINING  
1
21  
22  
23  
24  
CHAIN LINK KIT........................................... 1 .............. INCLUDES ITEMS W/  
*
BALL HITCH 2-INCH .................................... 1.............. CONTACT UNIT SALES  
LOOP HITCH ................................................ 1.............. CONTACT UNIT SALES  
PIN HITCH 1-INCH ....................................... 1.............. CONTACT UNIT SALES  
HPC-1  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — AXLE ASSY.  
AXLE ASSY.  
PAGE 40 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — AXLE ASSY.  
AXLE ASSY.  
NO  
1
PART NO  
PART NAME  
QTY.  
REMARK  
492584  
492394  
EM914288  
EM903113  
EM903012  
EM941306  
EM511159  
EM501299  
491688  
8164  
LOCK NUT 1/2" NC  
BOLT 1/2" NC 1-1/2" G5  
OIL SEAL  
8
8
2
4
4
2
3
4#  
#
#
*
BEARING CONE  
BEARING CUP  
5
6
7
8
9
HUB ASSY., 4-BOLT (1-1/16" SPINDLE) ........................ 2 ........... INCLUDES ITEMS W/  
#
WASHER, FLAT, .087" THICKNESS  
WASHER, FLAT, .135" THICKNESS  
COTTER PIN 1/8" X 1-1/2'  
NUT, SLOTTED HEX JAM 1"- 20  
TIRE AND RIM, CARLISE .............................................. 2 ........... BEFORE JANUARY 2006  
TIRE AND RIME, TOWMASTER II ................................. 2 ........... AFTER JANUARY 2006  
LUG NUTS  
DUST CAP  
AXLE, RIGID  
WASHER, FLAT  
2
AR  
2
10  
11  
11  
12  
13  
14  
15  
2
3005  
516476  
8115  
3469  
514679  
492600  
#
#
8
2
1
12  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — CABINET ASSY.  
CABINET ASSY.  
PAGE 42 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — CABINET ASSY.  
CABINET ASSY.  
NO  
1
2
PART NO  
490202  
514771  
PART NAME  
QTY.  
REMARKS  
RUBBER PROTECTOR  
4
ENGINE HOUSING CABINET W/DECALS ...........1................INCLUDES ITEM W//  
*
REPLACES P/N 514648  
3
4
5
6
7
492375  
EM923023  
13287  
2203  
1307  
BOLT 3/8" NC X 1" G5  
WASHER, FLAT 5/16"  
6
8
LOCK NUT 8-32 ....................................................6................REPLACEMENT PART ONLY  
WASHER, FLAT #10 .............................................6................REPLACEMENT PART ONLY  
RHMS 8-32 X 1/2" .................................................6................REPLACEMENT PART ONLY  
8/  
*
9
10  
11  
491010  
492598  
2105164  
EM974007  
LATCH ASSY., COMPLETE  
WASHER, FLAT 3/8"  
NUT 3/8" NC G5  
2
12  
6
PAINT, SPRAY CAN 12 OZ. TRAFFIC RED  
AR  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — GAS ENGINE MOUNTING PLATE ASSY.  
GAS ENGINE MOUNTING PLATE ASSY.  
PAGE 44 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — GAS ENGINE MOUNTING PLATE ASSY.  
GAS ENGINE MOUNTING PLATE ASSY.  
NO  
1
2
3
4
5
6
PART NO  
GX120K1QX2  
490956  
500246  
EM961045  
492066  
PART NAME  
ENGINE, HONDA 3.9 HP  
RING, RETAINING  
SQUARE KEY 1/4 X 35 MM  
SET SCREW 5/16" NC X 3/4"  
UPPER PULLEY  
QTY.  
REMARKS  
1
1
1
1
1
1
501019  
SQUARE KEY 3/16" X 45 MM  
7
7
8
9
507725  
EM507846  
492467  
V-BELT A-48 ................................................ 1 ........... USED UP TO JUNE 2005  
V-BELT A-50 ................................................ 1 ........... USED STARTING JULY 2005  
ALLEN SCREW 5/16" NC X 3/8"  
DRIVE PULLEY 4.0 HP  
WASHER, LOCK 5/16"  
WASHER, FLAT 5/16"  
NUT, HEX 5/16 X18 NC G5  
BASE PLATE, ENGINE  
WASHER, FLAT 1/2"  
1
1
4
4
4
1
8
4
1
1
1
4
4
1
492065  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
EM923343  
EM923023  
2105164  
514670  
492600  
EM963692  
29174-001  
29173-001  
510573C  
492584  
492367  
514684  
BOLT, HEX 1/2" NC 1-1/2" G5  
BUTTON, STOP  
SWITCH, STOP  
ENGINE CABLE HARNESS  
LOCKNUT 1/2"  
BOLT 5/16" X 1-3/4" G5  
SUPPORT BRACKET  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — ELECTRIC MOTOR MOUNTING PLATE ASSY.  
ELECTRIC MOTOR MOUNTING PLATE ASSY.  
PAGE 46 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MC-44S — ELECTRIC MOTOR MOUNTING PLATE ASSY.  
ELECTRIC MOTOR MOUNTING PLATE ASSY.  
NO  
1
2
3
4
5
6
PART NO  
34F3245596  
490956  
500246  
EM961045  
492066  
501019  
PART NAME  
MOTOR, ELECTRIC .5 HP  
RING, RETAINING  
SQUARE KEY 3/16" X 45 MM  
SET SCREW 5/16" NC X 3/4"  
UPPER PULLEY  
QTY.  
REMARKS  
1
1
1
1
1
1
SQUARE KEY 3/16" X 45 MM  
7
7
507725  
EM507846  
V-BELT A-48 ................................................ 1 ........... USED UP TO JUNE 2005  
V-BELT A-50 ................................................ 1 ........... USED STARTING JULY 2005  
8
9
492467  
492067  
EM923343  
EM923023  
492553  
502041  
492600  
EM963692  
4922584  
492367  
ALLEN SCREW 5/16" NC X 1/2"  
DRIVE PULLEY  
WASHER, LOCK 5/16"  
WASHER, FLAT 5/16"  
NUT, HEX 5/16 X18 NC G5  
BASE PLATE ENGINE  
WASHER, FLAT 1/2"  
BOLT, HEX 1/2" NC 1-1/2" G5  
LOCKNUT 1/2"  
BOLT 5/16" X 1-3/4"  
SUPPORT BRACKET  
1
1
4
4
4
1
8
4
4
4
1
10  
11  
12  
13  
14  
15  
16  
17  
18  
514684  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
PAGE 48 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
NO.  
1
2
3
*
4
PART NO.  
PART NAME  
QTY.  
REMARKS  
16271ZE1000  
17210ZE0505  
17218ZE0505  
17230ZE0820  
17232891000  
17238ZE0010  
17239ZE1000  
17410ZE0030  
90325044000  
957010602000  
9405006000  
GASKET, ELBOW  
1
ELEMENT, AIR CLEANER (DUAL) ................... 1.............INCLUDES ITEMS W/  
FILTER, OUTER  
COVER, AIR CLEANER (DUAL)  
GROMMET, AIR CLEANER  
COLLAR, AIR CLEANER  
COLLAR B, AIR CLEANER  
ELBOW, AIR CLEANER ................................... 1.............INCLUDES ITEMS W/  
WINGNUT, TOOL BOX SETTING  
BOLT, FLANGE 6X20  
NUT, FLANGE 6MM  
*
1
1
1
2
1
5
*
7
8
9
#
#
#
12  
13  
14  
2
1
2
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
PAGE 50 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
NO.  
1
2
3
4
PART NO.  
PART NAME  
QTY.  
REMARKS  
14100ZE0812  
14410ZE0010  
14431ZE1000  
14441ZE1010  
14451ZE1013  
14568ZE1000  
14711ZF0010  
14721ZF0000  
14751ZF1000  
14771ZE1000  
14773ZE1000  
14781ZE1000  
14791ZE0010  
90012ZE0010  
90206ZE1000  
CAMSHAFT ASSEMBLY.................................. 1.............INCLUDES ITEMS W/  
*
ROD, PUSH  
ARM, VALVE ROCKER  
LIFTER, VALVE  
PIVOT, ROCKER ARM  
SPRING, WEIGHT RETURN  
VALVE, IN.  
2
2
2
2
1
1
1
2
1
1
1
1
2
2
5
6
*
7
8
VALVE, EX.  
SPRING, VALVE  
9
10  
11  
12  
13  
14  
15  
RETAINER, IN. VALVE SPRING  
RETAINER, EX. VALVE SPRING  
ROTATOR, VALVE  
PLATE, PUSH ROD GUIDE  
BOLT, PIVOT 8MM  
NUT, PIVOT ADJ.  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CARBURETOR ASSY.  
CARBURETOR ASSY.  
PAGE 52 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CARBURETOR ASSY.  
CARBURETOR ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
*
2
*
3
*
4
*
5
*
6
*
7
*
8
*
9
16010ZE1812  
16011ZE0005  
16013ZE0005  
16015ZE1811  
16016ZH7W01  
16024ZE1811  
16028ZE0005  
16044ZE0005  
16100ZH7W51  
16124ZE0005  
16166ZH7W50  
16173001004  
16211ZE0000  
16212ZH7800  
16220ZE1020  
16221ZH8801  
16610ZE1000  
16953ZE1812  
16954ZE1811  
16956ZE1811  
16957ZE1812  
16967ZE0811  
93500030080G  
9430520122  
GASKET SET  
1
1
1
1
1
1
1
1
VALVE SET, FLOAT  
FLOAT SET  
CHAMBER SET, FLOAT  
SCREW SET  
SCREW SET, DRAIN  
SCREW SET B  
CHOKE SET  
CARBURETOR ASSEMBLY, BE60B B............. 1.............INCLUDES ITEMS W/  
SCREW, THROTTLE STOP  
NOZZLE, MAIN  
GASKET, FUEL STRAINER CUP  
INSULATOR, CARBURETOR  
GASKET, INSULATOR  
SPACER, CARBURETOR  
GASKET, CARBURETOR  
LEVER, CHOKE (STANDARD) ......................... 1.............INCLUDES ITEMS W/  
LEVER,VALVE  
PLATE, LEVER SETTING  
SPRING, VALVE LEVER  
GASKET, VALVE  
CUP, FUEL STRAINER  
SCREW, PAN (3 X 6)  
PIN, SPRING (2 X 12)  
JET, MAIN (#55) (OPTIONAL)  
JET, MAIN (#58) (OPTIONAL)  
JET, MAIN (#60)  
*
10  
1
1
1
1
1
1
1
*
11  
*
12  
*
13  
14  
15  
16  
17  
#
18  
1
1
1
1
1
2
1
1
1
1
1
*
19  
*
20  
*
21  
*
22  
*
23  
*
24  
25  
25  
25  
26  
#
99101ZH80550  
99101ZH80580  
99101ZH80600  
99204ZE00350  
*
*
JET, SET, PILOT (#35)  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CONTROL ASSY.  
CONTROL ASSY.  
PAGE 54 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CONTROL ASSY.  
CONTROL ASSY.  
NO.  
3
4
5
6
PART NO.  
PART NAME  
QTY.  
REMARKS  
16500ZH7820  
16551ZE0010  
16555ZE0000  
16561ZE0020  
16562ZE0020  
16571ZH7000  
16574ZE1000  
16575ZH8000  
16576891000  
16578ZE1000  
16580ZH7810  
16584883300  
16592ZE1810  
90013883000  
90015ZE5010  
90022888010  
90114SA0000  
93500050250H  
93500050160A  
9405006000  
CONTROL ASSEMBLY (REMOTE) ........... 1 ............ INCLUDES ITEMS W/  
#
ARM, GOVERNOR  
ROD, GOVERNOR  
SPRING, GOVERNOR  
SPRING, THROTTLE RETURN  
LEVER, CONTROL  
SPRING, LEVER  
WASHER, CONTROL LEVER  
HOLDER, CABLE  
SPACER, CONTROL LEVER  
BASE CONTROL  
SPRING, CONTROL ADJUSTING  
SPRING, CABLE RETURN  
BOLT, FLANGE 6X12 (CT200)  
BOLT, GOVERNOR ARM  
BOLT, FLANGE 6X20 (CT200)  
NUT, SELF- LOCK 6MM  
SCREW, PAN 5X25  
1
1
1
1
1
1
1
7
8#  
#
9
10  
11  
12  
14  
15  
16  
18  
19  
20  
21  
24  
25  
26  
#
#
#
#
#
#
1
1
1
1
1
1
1
1
1
1
#
#
#
SCREW, PAN  
NUT, FLANGE 6MM  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
PAGE 56 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
NO.  
1
2
PART NO.  
PART NAME  
QTY.  
REMARKS  
11300ZE0640  
11381ZH7800  
15600ZE1003  
15600ZG4003  
15625ZE1003  
15625ZE1003  
90015883000  
91001878003  
91203ZE0003  
9430108140  
COVER ASSEMBLY, CRANKCASE (W- TYPE)....... 1 ..............INCLUDES ITEMS W/  
*
#
GASKET, CASE COVER  
CAP ASSEMBLY, OIL FILLER ................................ 1 ..............INCLUDES ITEMS W/  
CAP ASSEMBLY, OIL FILLER ................................ 1 ..............INCLUDES ITEMS W/+  
GASKET, OIL FILLER CAP  
GASKET, OIL FILLER CAP  
BOLT, FLANGE 6X28  
BEARING, RADIAL BALL  
OIL SEAL 22X41X6  
1
3
4
7#  
1
1
7
1
1
2
8+  
9
10  
*
11  
12  
*
PIN A, DOWEL 8X14  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
PAGE 58 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
NO.  
1
2
PART NO.  
13310ZE0601  
90745ZE1600  
PART NAME  
CRANKSHAFT, H-TYPE  
KEY 4.78 X4.78X38  
QTY.  
1
1
REMARKS  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
PAGE 60 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
NO.  
2
3
PART NO.  
PART NAME  
QTY.  
REMARKS  
120A0ZH7810  
15510ZE1033  
16510ZE1000  
16511ZE1000  
16512ZE1000  
16513ZE1000  
16531ZE1000  
16541ZE1000  
90131ZE1000  
90451ZE1000  
90601ZE1000  
90602ZE1000  
91001878003  
91202ZE6003  
91353671003  
9405010000  
CYLINDER ASSEMBLY (OIL ALERT) ........1 ............ INCLUDES ITEMS W/  
*
#
SWITCH ASSEMBLY, OIL LEVEL  
GOVERNOR ASSEMBLLY .........................1 ............ INCLUDES ITEMS W/  
WEIGHT, GOVERNOR  
HOLDER, GOVERNORWEIGHT  
PIN, GOVERNOR WEIGHT  
SLIDER, GOVERNOR  
1
4
5#  
6#  
7#  
8
9
2
1
2
1
1
2
1
2
1
1
1
1
1
2
1
2
SHAFT, GOVERNOR ARM  
BOLT, DRAIN PLUG  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
WASHER, THRUST 6mm  
WASHER, DRAIN PLUG 10.2mm  
CLIP, GOVERNOR HOLDER  
BEARING, RADIAL BALL 62/22  
OIL SEAL 22X35X6  
O- RING 13.5X1.5 (ARAI)  
NUT, FLANGE 10mm  
WASHER, PLAIN 6mm  
PIN, LOCK 8mm  
BOLT, FLANGE 6X12  
*
*
9410106800  
9425108000  
957010601200  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
PAGE 62 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
12210ZH7000  
12204ZE1306  
12205ZE1315  
12216ZE5300  
12251ZH7800  
12310ZE1020  
12391ZE1000  
15721ZH8000  
90013883000  
90043ZE1020  
90047ZE1000  
9430110160  
CYLINDER HEAD ..................................................1.............. INCLUDES ITEMS W/  
*
2
GUIDE, VALVE (OS) OPTIONAL  
GUIDE, EX. VALVE (OS) OPTIONAL ...................1.............. INCLUDES ITEMS W/+  
CLIP, VALVE GUIDE  
GASKET, CYLINDER HEAD  
COVER, HEAD  
GASKET, CYLINDER HEAD COVER  
TUBE, BREATHER  
BOLT, FLANGE 6X12 (CT200)  
BOLT, STUD 6X109  
BOLT, STUD 8X32  
1
*
3
*
4 +  
1
1
1
1
1
4
2
2
2
4
1
*
5
6
7
8
9
10  
11  
12  
14  
15  
PIN, A, DOWEL 10X16  
BOLT, FLANGE 8X55  
SPARK PLUG BPR6ES (NGK)  
957230805500  
9807955846  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FAN COVER ASSY.  
FAN COVER ASSY.  
PAGE 64 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FAN COVER ASSY.  
FAN COVER ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
QTY.  
REMARKS  
11347371300  
19610ZE0000ZE  
19611ZH7810  
90601ZH7013  
19630ZH7000  
32197ZH8003  
36100ZE1015  
36101ZE1010  
90013883000  
90022888010  
34150ZH7003  
957010600800  
GROMMET, ADJUSTING COVER  
COVER, FAN *NH1* BLACK  
PLATE, SIDE (OIL ALERT)  
CLIP, HARNESS  
1
1
1
1
1
1
1
1
6
1
1
1
SHROUD  
SUB- HARNESS  
SWITCH ASSEMBLY, ENGINE STOP  
WIRE, STOP SWITCH 370MM  
BOLT, FLANGE 6X12 (CT200)  
BOLT, FLANGE 6X12 (CT200)  
ALERT UNIT, OIL  
9
10  
11  
13  
BOLT, FLANGE 6X8  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FLYWHEEL ASSY.  
FLYWHEEL ASSY.  
PAGE 66 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FLYWHEEL ASSY.  
FLYWHEEL ASSY.  
NO.  
1
2
4
5
PART NO.  
PART NAME  
KEY, SPECIAL WOODRUFF 25X18  
FAN, COOLING  
PULLEY, STARTER  
FLYWHEEL  
NUT, SPECIAL 14MM  
QTY.  
REMARKS  
13331357000  
19511ZE0000  
28451ZH8003  
31100ZE0010  
90201878003  
1
1
1
1
1
7
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FUELTANK ASSY.  
FUEL TANK ASSY.  
PAGE 68 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — FUELTANK ASSY.  
FUEL TANK ASSY.  
NO.  
1
2
3
5
PART NO.  
PART NAME  
RUBBER, SUPPORTER 107MM  
JOINT, FUEL TANK  
TANK, FUEL *NH1* (BLACK)  
CAP, FUEL FILLER ..................................... 1 .......... INCLUDES ITEMS W/  
GASKET, FUEL FILLER CAP  
O- RING 13.5X1.5 (ARAI)  
NUT, FLANGE 6MM  
BULK HOSE, FUEL (4.5X3000) (4.5X140)  
CLIP, TUBE (B8)  
QTY.  
REMARKS  
16854ZH8000  
16955ZE1000  
17510ZE0020ZD  
17620ZH7023  
17631ZH7003  
91353671003  
9405006000  
1
1
1
*
6
11  
1
1
2
1
2
1
*
12  
13  
14  
15  
950014500360M  
9500202080  
90004ZH7003  
BOLT, FLANGE 6X29  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
PAGE 70 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
NO.  
1
2
PART NO.  
PART NAME  
QTY.  
REMARKS  
30500ZE1033  
30700ZE1013  
90121952000  
COIL ASSEMBLY, IGNITION  
CAP ASSEMBLY, NOISE SUPPRESSOR  
BOLT, FLANGE 6X25  
1
1
2
8
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — MUFFLER ASSY.  
MUFFLER ASSY.  
PAGE 72 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — MUFFLER ASSY.  
MUFFLER ASSY.  
NO.  
1
3
7
10  
PART NO.  
PART NAME  
QTY.  
REMARKS  
18310ZF1000  
18320ZF1H01  
18381ZH8800  
90050ZE1000  
94001080000S  
MUFFLER  
1
1
1
4
2
PROTECTOR, MUFFLER  
GASKET, MUFFLER  
SCREW, TAPPING 5X8  
NUT, HEX. 8MM  
13  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — PISTON ASSY.  
PISTON ASSY.  
PAGE 74 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — PISTON ASSY.  
PISTON ASSY.  
NO.  
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.  
PART NAME  
QTY. REMARKS  
13010ZK7V01  
13011ZE6013  
13012ZK7V01  
13013ZK7V01  
13101ZH7000  
13102ZH7000  
13103ZH7000  
13104ZH7000  
13111ZE0000  
132A0ZE0000  
13200ZE0000  
90001ZE1000  
90551ZE0000  
RING SET, PISTON (STANDARD)  
RING SET, PISTON (OS 0.25), OPTIONAL  
RING SET, PISTON (OS 0.50) , OPTIONAL  
RING SET, PISTON (OS 0.75), OPTIONAL  
PISTON, STANDARD  
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25  
PISTON, OS 0.50  
PISTON, 0.75  
PIN, PISTON  
ROD ASSY, CONNECTING (UNDER SIZE) .... 1 ...... INCLUDES ITEMS W/  
ROD ASSEMBLY, CONNECTING.................... 1 ...... INCLUDES ITEMS W/  
BOLT, CONNECTING ROD  
CLIP, PISTON PIN 13MM  
*
*
2
2
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
PAGE 76 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
28400ZH8013ZB  
28410ZH8003ZB  
28420ZH8013  
28422ZH8013  
28433ZH8003  
28441ZH8003  
28442ZH8003  
28443ZH8003  
28461ZH8003  
28462ZH8003  
90003ZH8003  
9008ZE2003  
STARTER ASSY., RECOIL *NH1* (BLACK) ..........1.............. INCLUDES ITEMS W/  
*
2
CASE, RECOIL STARTER *NH1* (BLACK)  
REEL, RECOIL STARTER  
RATCHET, STARTER  
GUIDE, RATCHET  
SPRING, FRICTION  
SPRING, RECOIL STARTER  
SPRING, RETURN  
KNOB, RECOIL STARTER  
ROPE, RECOIL STARTER  
SCREW, SETTING  
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10  
*
11  
*
12  
BOLT, FLANGE 6X10  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — GASKET KIT ASSY.  
NO ARTWORK AVALIBLE  
PAGE 78 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — GASKET KIT ASSY.  
GASKET KIT ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
2
06111ZH7405  
11381ZH7800  
12251ZH7800  
12391ZE1000  
16212ZH7800  
16221ZH8801  
18381ZH8800  
GASKET KIT ......................................................... 1.............. INCLUDES ITEMS W/  
*
3
*
4
*
5
*
6
*
7
*
8
*
GASKET, CASE COVER  
GASKET, CYLINDER HEAD  
GASKET, CYLINDER HEAD COVER  
GASKET, INSULATOR  
GASKET, CARBURETOR  
GASKET, MUFFLER  
1
1
1
1
1
1
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — LABELS ASSY.  
LABELS ASSY.  
PAGE 80 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX120K1QX2 ENGINE — LABELS ASSY.  
LABELS ASSY.  
NO.  
1
3
4
6
PART NO.  
PART NAME  
RING SET, PISTON (STANDARD)  
LABEL CAUTION  
MARK CHOKE  
MARK, OIL ALERT  
QTY. REMARKS  
87521ZH7020  
87522zH9000  
87528ZE1810  
87532ZH8810  
1
1
1
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TERMS AND CONDITIONS OF SALE — PARTS  
5. Parts must be in new and resalable  
condition, in the original Multiquip  
package (if any), and with Multiquip part  
numbers clearly marked.  
Multiquip reserves the right to quote and  
sell direct to Government agencies, and to  
Original Equipment Manufacturer accounts  
who use our products as integral parts of their  
own products.  
PAYMENT TERMS  
Terms of payment for parts are net 30 days.  
FREIGHT POLICY  
6. The following items are not returnable:  
All parts orders will be shipped collect or  
prepaid with the charges added to the invoice.  
All shipments are F.O.B. point of origin.  
Multiquip’s responsibility ceases when a  
signed manifest has been obtained from the  
carrier, and any claim for shortage or damage  
must be settled between the consignee and  
the carrier.  
a. Obsolete parts. (If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
SPECIAL EXPEDITING SERVICE  
A $35.00 surcharge will be added to the  
invoice for special handling including bus  
shipments, insured parcel post or in cases  
where Multiquip must personally deliver the  
parts to the carrier.  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
prior to the return date.  
LIMITATIONS OF SELLER’S LIABILITY  
MINIMUM ORDER  
Multiquip shall not be liable hereunder for  
damages in excess of the purchase price of  
the item with respect to which damages are  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
other special, consequential or incidental  
damages.  
The minimum charge for orders from Multiquip  
is $15.00 net. Customers will be asked for  
instructions regarding handling of orders not  
meeting this requirement.  
c. Any line item with an extended  
dealer net price of less than  
$5.00.  
d. Special order items.  
RETURNED GOODS POLICY  
e. Electrical components.  
f. Paint, chemicals, and lubricants.  
g. Decals and paper products.  
h. Items purchased in kits.  
Return shipments will be accepted and  
credit will be allowed, subject to the following  
provisions:  
LIMITATION OF WARRANTIES  
No warranties, express or implied, are  
made in connection with the sale of parts or  
trade accessories nor as to any engine not  
manufactured by Multiquip. Such warranties  
made in connection with the sale of new,  
complete units are made exclusively by a  
statement of warranty packaged with such  
units, and Multiquip neither assumes nor  
authorizes any person to assume for it  
any other obligation or liability whatever in  
connection with the sale of its products. Apart  
from such written statement of warranty,  
there are no warranties, express, implied or  
statutory, which extend beyond the description  
of the products on the face hereof.  
1. A Returned Material Authorization  
must be approved by Multiquip prior to  
shipment.  
7. The sender will be notified of any material  
received that is not acceptable.  
8. Such material will be held for five  
working days from notification, pending  
instructions. If a reply is not received  
within five days, the material will be  
returned to the sender at his expense.  
2. To obtain a Return Material Authorization,  
a list must be provided to Multiquip  
Parts Sales that defines item numbers,  
quantities, and descriptions of the items  
to be returned.  
9. Credit on returned parts will be issued  
at dealer net price at time of the original  
purchase, less a 15% restocking  
charge.  
a. The parts numbers and descriptions  
must match the current parts price  
list.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
based on the list price that was effective  
twelve months prior to the RMA date.  
c. The list must state the reason(s)  
for the return.  
Effective: February 22, 2006  
d. The list must reference the sales  
order(s) or invoice(s) under  
which the items were originally  
purchased.  
11. Credit issued will be applied to future  
purchases only.  
PRICING AND REBATES  
e. The list must include the name  
and phone number of the person  
requesting the RMA.  
Prices are subject to change without prior  
notice. Price changes are effective on a  
specific date and all orders received on or  
after that date will be billed at the revised price.  
Rebates for price declines and added charges  
for price increases will not be made for stock  
on hand at the time of any price change.  
3. AcopyoftheReturnMaterialAuthorization  
must accompany the return shipment.  
4. Freight is at the sender’s expense. All  
parts must be returned freight prepaid to  
Multiquip’s designated receiving point.  
PAGE 82 —MC-44S CONCRETE MIXER— OPERATION & PARTS MANUAL — REV. #8 (09/15/11)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MC-44S CONCRETE MIXER — OPERATION & PARTS MANUAL — REV. #8 (09/15/11) — PAGE 83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION AND PARTS MANUAL  
HERE’S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL  
NUMBER ON-HAND WHEN CALLING  
UNITED STATES  
Multiquip Corporate Office  
MQ Parts Department  
18910 Wilmington Ave.  
Carson, CA 90746  
Contact: mq@multiquip.com  
Tel. (800) 421-1244  
Fax (800) 537-3927  
800-427-1244  
310-537-3700  
Fax: 800-672-7877  
Fax: 310-637-3284  
Service Department  
Warranty Department  
800-421-1244  
310-537-3700  
Fax: 310-537-4259  
Fax: 310-943-2238  
800-421-1244  
310-537-3700  
Fax: 310-537-1173  
Technical Assistance  
800-478-1244  
MEXICO  
UNITED KINGDOM  
MQ Cipsa  
Multiquip (UK) Limited Head Office  
Carr. Fed. Mexico-Puebla KM 126.5  
Momoxpan, Cholula, Puebla 72760 Mexico  
Contact: pmastretta@cipsa.com.mx  
Tel: (52) 222-225-9900  
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223  
Fax: (52) 222-285-0420 Globe Lane,  
Dukinfield, Cheshire SK16 4UJ  
Contact: sales@multiquip.co.uk  
Fax: 0161 339 3226  
CANADA  
Multiquip  
4110 Industriel Boul.  
Laval, Quebec, Canada H7L 6V3  
Contact: jmartin@multiquip.com  
Tel: (450) 625-2244  
Tel: (877) 963-4411  
Fax: (450) 625-8664  
© COPYRIGHT 2011, MULTIQUIP INC.  
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property  
of their respective owners and used with permission.  
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in  
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published  
in this publication at any time without notice and without incurring any obligations.  
Your Local Dealer is:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Clothes Dryer T 4464 C User Manual
Miele Dishwasher G 4205 User Manual
Multi Tech Equipment Indoor Furnishings MLT20DCA User Manual
Novatel Car Stereo System OM 20000149 User Manual
Optimus Cassette Player CTR 108 User Manual
Oregon Scientific Digital Camera DS6888 User Manual
Oster Automobile 76023 User Manual
OTC Wireless Computer Monitor AVCW 100 200 User Manual
Palsonic Computer Monitor TFTV385 User Manual
Panasonic DVR WJ HD500A User Manual