OPERATION AND PARTS MANUAL
MODEL AR13D
RIDE-ON TANDEM DRUM ROLLER
SERIES DRIVE SYSTEM
(DIESEL ENGINE)
Revision #2 (09/15/11)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —TABLE OF CONTENTS
MULTIQUIP AR13D
COMPONENT DRAWINGS
RIDE-ON TANDEM DRUM
ROLLER
Explanation Of Code In Remarks Column.............. 48
Suggested Spare Parts ........................................... 49
Name Plate and Decals ..................................... 50-51
Front Drum Assembly ........................................ 52-53
Exciter Assembly................................................ 54-55
Rear Drum and Chassis Assembly .................... 56-57
Covers and Frame Articulation Lock Assy. ........ 58-59
Hood and Rear Panel Assembly ........................ 60-61
Steering Column and Hydraulic Artic. Assy. ...... 62-63
Articulation Arm Assembly ................................. 64-65
Hydraulic Drive Pump Assembly ........................ 66-67
Manifold and Hydraulic Oil Filter Assembly........ 68-69
Fuel Tank and Oil Drain Hose Assembly............ 70-71
Water Tank Assembly ......................................... 72-73
Engine Mounting Assembly ............................... 74-75
Muffler Assembly ............................................... 76-77
Air Cleaner Assembly......................................... 78-79
Radiator Assembly ............................................. 80-81
Throttle Assy. ..................................................... 82-83
Brake Control Assy............................................. 84-85
Battery Assy. ...................................................... 86-87
Scraper Assy. ..................................................... 88-89
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation .................................... 8-10
Operation and Safety Decals ............................. 11-12
Specifications (Roller) ............................................. 13
Specifications (Engine) ........................................... 14
Dimensions ............................................................. 15
General Information ........................................... 16-17
Roller Components ............................................ 18-20
Engine Components ............................................... 21
Inspection........................................................... 22-24
Initial Start-Up ......................................................... 25
Operation ................................................................ 26
Maintenance ...................................................... 27-36
Preparation For Long-Term Storage ...................... 37
Manifold Test Ports.................................................. 38
Hydraulic System Diagram ..................................... 39
Electric Wiring Diagram ........................................... 40
Hydraulic Hose Connectsion.............................. 42-43
Troubleshooting (Roller).......................................... 44
Troubleshooting (Engine)................................... 45-46
Terms and Conditions of Sale ................................. 90
Specification and part number
are subject to change without
notice.
PAGE 4 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
UPS/Fed Ex
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
■ Next Day
Applicable Model Number
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
All orders are treated as Standard Orders
andwillshipthesamedayifreceivedprior
to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Potential hazards associated with operation of the pump will be
referenced with Hazard Symbols which appear throughout this
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
manual, and will be referenced in conjunction with Safety
Lethal Exhaust Gases
Message Alert Symbols.Some examples are listed below:
This Owner's Manual has been developed to
provide complete instructions for the safe and
efficient operation of the Multiquip Model
AR13D Ride-on Tandem Drum Roller. Refer to
the engine manufacturers instructions for data
relative to its safe operation.
WARNING - LETHAL EXHAUST GASES
Gasoline engine exhaust gases contain
poisonous carbon monoxide. This gas is
colorless and odorless, and can cause
death if inhaled. NEVER operate this
equipment in a confined area or enclosed
Before using this roller,ensure that the operating individual
has read and understands all instructions in this manual.
structure that does not provide ample free flow air.
SAFETY MESSAGE ALERT SYMBOLS
WARNING - EXPLOSIVE FUEL
Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids. DO NOT fill the fuel
tank while the engine is running or hot.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
DO NOT overfill tank, since spilled fuel
could ignite if it comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in approved
containers, in well-ventilated areas and away from sparks and
flames. NEVER use fuel as a cleaning agent.
DANGER
You WILL be KILLED or SERIOUSLY injured if you do
not follow directions.
WARNING - BURN HAZARDS
WARNING
Engine components can generate extreme
heat. To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operations. NEVER operate
the engine with heat shields or heat guards
removed.
You COULD be KILLED or SERIOUSLY injured if you
do not follow directions.
CAUTION
You CAN be injured if you do not follow directions
PAGE 6 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SAFETY MESSAGE ALERT SYMBOLS
WARNING - ROTATING PARTS
CAUTION - RESPIRATORY HAZARDS
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
ALWAYS wear approved respiratory
protection.
CAUTION - ACCIDENTAL STARTING
CAUTION - SIGHT AND HEARING HAZARDS
ALWAYS place the Engine ON/OFF switch
in the OFF position and remove the ignition
key when the pump is not in use.
ALWAYS wear approved eye and
hearing protection.
CAUTION - OVER-SPEED CONDITIONS
CAUTION - EQUIPMENT DAMAGE MESSAGES
NEVER tamper with the factory settings of
the engine governor or settings. Personal
injury and damage to the engine or
equipment can result if operating in speed
ranges above maximum allowable.
Other important messages are provided throughout this manual
to help prevent damage to your concrete pump, other property,
or the surrounding environment.
This Ride-onTandem Drum Roller, other property,
or the surrounding environment could be
damaged if you do not follow instructions.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — RULES FOR SAFE OPERATION
■
NEVERtouchthehotexhaustmanifold, mufflerorcylinder.
Allow these parts to cool before servicing
engine or pump.
DANGER - ReadThis Manual!
Failure to follow instructions in this manual may lead to serious
injury or even DEATH! This equipment is to be operated by
trained and qualified personnel only! This equipment is for
industrial use only.
■
High Temperatures – Allow the engine
to cool before adding fuel or performing
service and maintenance functions.
Contact with hot components can cause
serious burns.
The following safety guidelines should always be used when
operating the AR13D Ride-on Tandem Drum Roller:
■
The engine of this roller requires an adequate free flow of
cooling air. Never operate the roller in any enclosed or narrow
area where free flow of the air is restricted. If the air flow is
restricted it will cause
GENERAL SAFETY
■
■
■
DONOToperateorservicethisequipmentbefore
readingthisentiremanual.
This equipment should not be operated by
persons under 18 years of age.
serious damage to the
roller or engine and may
cause injury to people
and property.Remember
the roller's engine gives
off DEADLY gases.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
■
■
■
NEVER operate this equipment when not feeling well due to
fatigue, illness or taking medicine.
NEVER operate this equipment under the influence or drugs or
alcohol.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or explosion
could result from fuel vapors, or if fuel is spilled on a hot
engine.
ALWAYS check the machine for loosened threads or bolts
before starting.
ALWAYS wear proper respiratoty (mask) hearing and eye
protection equipment when operating the roller.
■
NEVER operate the Ride-on Tandem
Drum Roller in an explosive atmosphere
or near combustible materials. An
explosion or fire could result causing
severe bodily harm or even death.
■
■
NEVER operate this equipment when not feeling
well due to fatigue, llness or taking medicine.
■
■
Topping-off to filler port is dangerous, as it tends to spill fuel.
NEVER operate this equipment under the
influence of drugs or alcohol.
Refer to the Engine Owner's Manual for engine technical
questions or information.
■
■
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
PAGE 8 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — RULES FOR SAFE OPERATION
■
■
■
■
NEVER Run engine without air cleaner. Severe engine
MAINTENANCE SAFETY
damage may occur.
■
NEVER lubricate components or attempt service on a running
ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
machine.
■
ALWAYS allow the machine a proper amount of time to cool
ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using roller.
before servicing.
■
■
Keep the machinery in proper running condition.
ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children.
Fix damage to the machine immediately and always replace
broken parts, or missing decals.
■
■
■
Dispose of hazardous waste properly.Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■
■
■
DO NOT operate this roller with hydrostatic oil temperature
higher than 180 degrees fahrenheit.
DO NOT use food or plastic containers to dispose of
hazardous waste.
NEVER leave the roller unattended, turn off engine and place
parking brake lever in upright position.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
CAUTION must always be observed while servicing this roller.
Rotating parts can cause injury if contacted.
■
■
DO NOT leave roller with engine running.
If the roller must be stopped on an incline (grade), remove the
ignition key and place chock blocks (not provided) under the
front and rear drums.
■
■
NEVER drive the roller on unshored trenches or near steep,
unsupported banks.The vibration caused by the roller could
cause a cave-in.
ALWAYS use extreme care when operating near obstructions,
on slippery surfaces, grades and side slopes.
■
■
ALWAYS wear slip resistant safety shoes or boots.
Unauthorized equipment modifications will void all
warranties.
■
When working on slopes, avoid sidehill travel. Operate up
and down travel only. Remember, the danger of sliding on
and/or tripping on steep slopes is always present.
■
■
ALWAYS wear seat belts.
When malfunctions occur, always remove the ignition key
and place a "DO NOT OPERATE " sign in the operator's
seat.
■
If a malfunction occurs with the travel lever mechanism, speed
and direction will be impossible to control. Immediately stop
the roller and correct the problem.
■
■
If the steering system operates improperly, immediately stop
the engine and apply the parking brake.
In the event of hydraulic hose or line failure, promptly return
the travel lever to the “neutral” position, stop the engine and
set the parking brake.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — RULES FOR SAFE OPERATION
LOADING ANDTRANSPORTING SAFETY
EMERGENCIES
■
ALWAYS know the location of the
nearest fire extinguisher.
DANGER - Loading & Unloading the Roller
DANGER! ALWAYS load and unload the roller on Level,
Hard Ground, or Pavement. Serious injury or death can
result from improper loading, lifting or unloading. Use extreme
caution!
■
■
ALWAYS know the location of the
nearest and first aid kit.
■
The roller has an operating weight of approximately 3,088
lbs. (1,400 Kg). Use lifting equipment capable of lifting this
weight.
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
ALWAYS check the roller's lifting hooks. Before lifting or
transporting the roller, lock the frame with the locking bar that
is provided. Make sure the hooks are secure and tight before
lifting the machine.
■
■
When driving the roller onto a transporting vehicle or trailer,
use ramps or other suitable material of sufficient strength to
support the roller.
Remove mud, oil, ice, snow or any other slippery materials
from the ramps and bed of the vehicle to avoid accidents.
■
■
After loading, apply the parking brake.
Use a chain, binders or other suitable means to firmly secure
the roller before transporting.
■
■
Only use the lifting points for the roller that are clearly marked
as “lifting point ”.
NEVER apply chains through the articulating section of the
roller. The chain could cause damage by scoring the hydraulic
steering cylinder.
■
NEVER stand below roller when it is being lifted.
DANGER - Transporting Safety
DO NOT allow personnel to stand under or near any
suspended machine. Serious injury or death may result.
PAGE 10 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — OPERATION AND SAFETY DECALS
Machine Safety Decals
The AR13D Ride-onTandem Drum Roller is equipped with a number of safety decals.These decals are provided for operator safety
and maintenance information.The illustration below and on the next page shows these decals as they appear on the machine.
Should any of these decals become unreadable, replacements can be obtained from your dealer.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — OPERATION AND SAFETY DECALS
PAGE 12 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SPECIFICATIONS (ROLLER)
Table 1. AR-13D Roller Specifications
Shipping Weight
2,700 lbs. (1,225 Kg.)
2,556 lbs. (1,160 Kg.)
3,360 lbs. (1,524 Kg.)
3,437 lbs. (1,559 Kg.)
90.5 in. (2,286 mm.)
38.25 in. (972 mm.)
Dry Weight
Operating Weight
Operating Weight w/ Drum Ballast
Overall Length
Overall Width
Overall Height-ROPS (up)
Maximum Rolling Width
Turning Radius-Inside
Ground Clearance
87.0 in. (2,210 mm.)
35.7 in. (907 cm.)
109 in. (2,768 mm.)
11.5 in. (292 mm.)
Curb Clearance
7.75 in. L, 19.0 in. R (197 mm., 483 mm.)
1.75 in L, 1.25 in. R (45 mm., 32 mm.)
45 in. (1,143 mm.)
Wall Clearance
Wheelbase
Drum Width
35.7 in. (907mm.)
Drum Diameter
22.6 in. (574 mm.)
Drum Thickness
0.38 in. (10.0 mm.)
Centrifugal Force @ 2,400 - 2,700 rpm
Vibrations per minute @ 2,400 - 2,700 rpm
3,100 lbs. (1,406 Kg.)
4,000 VPM
Dynamic Linear
Force per Drum 2,400 - 2,700 rpm
87.5 lbs./in. (39.6 Kg./cm.)
(front only)
Oscillating Angle
Hydraulic Oil Tank Capacity
Cooling System
11 degrees
5.7 U.S. Gallons (21.6 Liters)
Air
Fuel
Diesel
Fuel Tank Capacity
Water Tank Capacity
Battery
9.5 U.S. Gallons (36 Liters)
40 Gallons (152 Liters)
12 Volt GroupType U1
0-4.8 MPH (0-7.7 KPH)
15 degrees (27%)
Travel Speed -variable
Grade Ability w-w/o Vibration
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SPECIFICATIONS (ENGINE)
Table 2. Engine Specifications
Model
Briggs & Stratton DM 850D
Diesel Engine
Type
Number of Cylinders
[Bore x Stroke]
Displacement
3
2.67 in. x 307 in. (68 mm x 78 mm)
51.8 cu. in. (850 cc)
23.6 gross
21.1 (net intermittent)
18.3 ( net continuous)
Horsepower
HP@ 3600RPM
Max. Torque
Ft./lbs. @ 2400 RPM
40.0/2400 gross
35.0/2400
Dry Weight
185.0 lbs. (84.0 kg.)
3.17 qts. (3.0 liters)
3.5 qts. (3.3 liters)
Engine Oil without Filter
Engine Oil with Filter
PAGE 14 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — DIMENSIONS
Figure 1. AR13D Roller Dimensions
Table 3. AR-13D Dimensions
Wheelbase
A
B
C
D
E
F
G
H
I
45.0 in. (1,143 mm.)
Drum Diameter
Curb Clearance
Drum Width
22.6 in. (574 mm.)
7.75 in. Left, 19.0 in. Right ( 197 mm., 483 mm.)
35.7 in. (907 mm.)
Overall Height (with ROPS)
Ground Clearance
Overall Length
Wall Clearance
Drum Thickness
Overall Width
87 in. (2,210 mm.)
11.5 in. (292 mm.)
90.5 in. (2,147 mm.)
1.75 in. Left, 1.25 in. Right ( 45 mm., 32 mm.)
.38 in. (10 mm.)
J
38.25 in. (972 mm.)
Seat Height
K
L
63 in. (1,600 mm.)
Steering Wheel
60 in. (1,524 mm.)
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — GENERAL INFORMATION
The roller nominally has an operating weight of 3,088 lbs (1,400
Kg.), but can be increased to 3,309 lbs (1,500 Kg.) by adding
water ballast to the rear drum.
The AR13D roller has been designed for asphalt application
and compaction of granular soils used in site preparation. Use
the machine only for the purpose intended and by experienced
personnel who understand this operating manual and all safety
decals. Typical applications for this roller are driveways, patch
work and road repairs. Standard features included with this roller
are articulated steering, double drum hydrostatic drive, front drum
vibration, high curb clearance and on board water capability.
HYDRAULIC OIL FILTER SYSTEM
The hydraulic system oil is filtered by a screen type filter located
in the reservoir filler neck, then doubled filtered within the system
first by a 40 micron mesh-type suction filter located in the tank
and the by a Zinga 10 micron, cartridge style spin-on return line
filter.
POWER PLANT
The AR13D roller is powered by a Brigss & Stratton DM 850D,
liquid cooled, diesel engine rated at 23.6 hp @3,600 rpm. The
engine is of a lightweight design and is exceptionally well
balanced for low vibration.
ARTICULATED STEERING SYSTEM
Power for the articulated steering system, which uses a single
hydraulic cylinder is provided by the gear pump. This steering
system can produce an inside turning radius of 109 inches (2.77
meters).
HYDRAULIC SYSTEM
The Brigss & Stratton DM 850D diesel engine drives an axial
hydraulic, variable displacement pump which is manually
controlled via a cable control system. Pump flow is directed
through an aluminum block manifold which provides the control
for the 3 hydraulic motors.
SPRINKLER SYSTEM
A 40 gallon (152 liters) water tank with a gravity feed spray bar
is provided for wetting the roll for asphaltic pavement rolling.
The water system is fully adjustable from the operator’s position
by adjusting the two water valves. The front valve controls the
water supply to the front drum, and the rear valve controls water
to the rear drum.
The hydraulic drum drive system incorporates a parallel closed
loop configuration operating at a maximum pressure of 2,900
psi. In addition this hydraulic system offers a "free wheel valve"
which allows the roller to be towed in the event of an emergency.
Before starting an asphalt rolling job, be sure all spray bar holes
are clear of dirt or foreign matter and are working. Always use
clean fresh water in the water tank.To prevent rust and foreign
debris from clogging the spray bar holes, drain and flush water
tank and spray bars every 30 days.
COMPACTION SYSTEM
The compaction force is delivered by a 36-inch wide steel drum
with beveled edges to help prevent asphalt marring. A fully
enclosed hydrostatic drive system offers a variable speed control
as well as smooth acceleration and braking.
LIFTING THE ROLLER
When lifting of the roller is required, attach a suitable
hook or shackle to the lifting eye of the roller. These
lifting points (4) are marked by a lifting hook decal. Make
sure the lifting device is capable of lifting 4,000 lbs. (1,814 Kg).
Connected to the axial hydraulic pump is a gear pump that
provides power for the drum vibratory system and the articulating
steering system. Oil from this pump flows to the manifold control
valve block and then to a hydraulic motor which rotates the
eccentric weights inside a sealed housing containing oil to
lubricate the bearings.
DANGER - Clear Obstacles from Area
A pushbutton switch located on top of the gearshift lever when
pressed activates a hydraforce valve that engages or disgages
the vibratory action. The drum's vibratory action generates 3,100
lbs. (1,406 Kg.) of centrifugal force at a frequency of 4,000 vpm
(vibrations per minute). If the vibration appears to be weak or
slow, allow the machine to warm-up thoroughly, and check the
hydraulic oil level. Add hydraulic oil if necessary.
Before operating the roller, make sure that personnel and
obstacles are free from the roller’s path. Serious injury or
even death can result!
The forward-reverse control lever operates the hydrostatic pump
which governs the roller speed and direction of travel.The speed
in which movement of this lever is made is directly related to the
amount of pressure that is applied to the travel lever in each
direction.Travel speed is infinitely variable from 0 to 4.8 mph.The
neutral position of this lever will cause the roller to stop.
The vibrator housing and drum are shock mounted to isolate the
engine compartment and operator from vibration.
PAGE 16 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — GENERAL INFORMATION
Tipping (Rollovers)
DANGER - Transporting Safety
NEVER! operate the roller on side slopes (Figure 3). The
possibility exist that the roller could tip over (roll over), thus
causing bodily harm even death and serious damage to the
equipment.
DO NOT allow personnel to stand under or near any
suspended machine. Serious injury or death may result.
CAUTION - Use CERTIFIED Lifting Devices
ONLY! use approved certified lifting devices capable of lifting
at least 4,000 lbs. (1,814 Kg.).
SIDE TO SIDE
OPERATION
NOT RECOMMENDED
CAUTION - Lifting the Roller
When lifting of the roller is required, only use the provided
lifting eyes to lift the roller. Using other sections of the roller
for lifting purposes may cause severe damage to the roller.
OPERATING ON SLOPES
ROLL OVER
Special care must be taken when operating the roller on hills or
slopes. There exist the possibility of serious injury to the operator
and severe damage to the roller in the event of a roll over.ALWAYS
operate the roller up and down hills rater than from side to side.
For safe operation hillside slopes should not exceed 12 degree
(27 % grade).See Figure 2 below.
Figure 3. Tipping (Rollover)
NEVER! operate the roller on side slopes.
The roller may tip over causing injury to
personnel and severe damage to the
equipment
MAXIMUM SLOPE
In the event the roller does tip over, if at all possible, try to shut-
down the engine by turning the ignition key to the OFF position.
Extreme care must be taken to prevent damage to the engine.
When the roller has been tipped over, oil from the engine
crankcase can flow into the combustion chamber, which can
severely damage the engine the next time it is started.
27%
IMMEDIATELY after a unit has tipped over upright the unit as
soon as possible to prevent oil from leaking into the combustion
chamber.
Figure 2. Recommend Slope
CAUTION - Roller Rollover Safety
To prevent damage to the engine after a rollover, the roller
must NOT be started. NEVER start a roller after a rollover.
CONTACT your nearest authorized multiquip dealer for
instructions or servicing.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ROLLER COMPONENTS
Figure 4. Roller Components 1
PAGE 18 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ROLLER COMPONENTS
Figure 4 shows the location of the components and basic
12. Rear Spray Control Valve – This valve controls the
flow of water to the rear spray bar.Turn the water valve
to the open position (counterclockwise) to let water flow,
return this valve to the closed position (clockwise) when
water is not required.
components for the AR13D compaction roller. The function of
each component or control is described below:
1.
2.
Battery – Provides +12VDC to the electrical system,
and is located underneath foot plate. Replace only with
recommended type battery, see specification Table 1.
13. Throttle Control — Pull all the way out to achieved
maximum engine RPM's.To idle the engine, push the RED
stop button inwards all the way.
Articulating Locking Bar – Always make sure that the
articulating locking bar is engaged during lifting,
transport and maintenance.
14. Vibration Control Button – Press this button to activate
the eccentric that will produce a vibration frequency of
4,400 vpm (vibrations per minute). Pressing the button
again will stop the vibrations.
3.
4.
5.
6.
Foot Step – To lift yourself onto the roller's platform,
place foot into foot step, then grab hold of hand rail.
Ignition Switch – With key inserted, turn clockwise to
start the engine.
15. Shift Lever — Push the lever forward to makethe roller
travel in a forward direction, pull the lever backward to
make the roller travel in a reverse direction. Maximum travel
speed is 4.8 MPH ( 7.7 KPH). Center position is neutral, no
travel.
Rear Sprinkler System – A gravity feed spray bar is
provided for the wetting the roll for asphalt pavement.
Rear Roller – This roller is a 30 inch wide steel drum
with beveled edges (no vibration). The beveled edges
help prevent asphalt marring.
16. Hour meter — Indicates the number hours the unit has
been in use.
7.
8.
Lifting Point – Attach a crane or suitable lifting device
17. WaterTank — Remove filler cap and fill with water.Water
tank capacity is 40 gallons (152 liters).To determine if water
level is low, visually inspect water level gauge (tube) at
rear of roller.Add water as necessary.
to this point when lifting of the roller is required.
Rear Scrapper – This adjustable rear scrapper blade
helps prevent the buildup of material between the drum
and frame.
18. Roll-Over Bar — This unit may be equipped with a Roll
Over Protection System (ROPS) to protect the operator
when the roller is used on slopes, open trenches, sharp
turns, slippery surfaces or objects in the rollers's path of
travel.
9.
Fuel Tank/Fuel Gauge – The fuel capacity of the fuel
tank is 9.5 gallons (36 liters). Read the gauge on top of
the fuel cap to determine if fuel level is low. Fill with
diesel fuel.To gain access to the fuel tank, tilt the front
seat forward. Fuel tank has a spill containment feature
19. Operator's Seat — A contoured seat that provides visibility
of both front rear drum edges during operation. NEVER!
start the roller unless seated in the operator's seat.
10. Tie-DownTransport Point – Attach a chain or suitable
tie-down device to this point when transporting of the is
required.
20. Parking Break Lever — Pull the lever upward to set the
parking break. To release the parking break, press and
hold the button on top of the lever and push lever downward.
21. Seat Belt — When using the roller in working conditions
always have the operator wear the seat belt. NEVER use
the roller without a seat belt. If the seat belt becomes worn
or damaged, have it replaced immediately.
TRANSPORT
TIE-DOWN POINT
22. SteeringWheel — Use this wheel to steer the roller.
23. Engine Status Indicator Gauge — Indicates oil
temperature, water temperature, glow plug and battery.
24. Hydraulic Motor – This hydraulic motor provides
control for the rear of the roller
11. Front Spray Control Valve – This valve controls the
flow of water to the front spray bar.Turn the water valve
to the open position (counterclockwise) to let water flow,
return this valve to the closed position (clockwise) when
water is not required.
25. Documentation Box — Maintain and store at all times
Operation, Parts, and Engine manuals in this box.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ROLLER COMPONENTS
Figure 5. Roller Components 2
Figure 5 shows the location of additional components for the
AR13D compaction roller. The function of each component or
control is described below:
34. Steering Cylinder – Controls direction of roller.
35. Engine – This roller incorporates a Briggs & Stratton
DM850D, liquid-cooled diesel engine rated at 23.6 hp
at 3,600 rpm.
26. Front Sprinkler System – A gravity feed spray bar is
provided for the wetting the roll for asphalt pavement.
36. Hydraulic Fluid Filler Port – Remove this cap to add
hydraulic fluid. Fill with type ISO 46 anti-wear hydraulic
fluid.
27. Hydraulic Manifold – Aluminum block that controls the
flow of hydraulic pressure to the various hydraulic motors
and other components required to control the roller.
37. Compartment Hood – Houses the engine, hydraulic
manifold, accessory relay, hydraulic oil filter, hoses, and
hydraulic pump. To lift the compartment hood, release
the rubber bunjee latches located on each side of the
hood.
28. Hydraulic Oil Filter – Filters return oil from the front
and rear hydrostatic motors.
29. Fuel Filter/Fuel Pump – Electrical device that pumps
fuel from the fuel tank to the carburetor.
30. Hydraulic Pump – This unit incorporates an axial
38. Compartment Hood Lift Point – Place hand here then
variable displacement hydraulic piston pump.
lift upwards to lift compartment hood.
31. Front Ride-on Tandem Drum Roller – This roller is a
30 inch wide steel drum with beveled edges. The
beveled edges help prevent asphalt marring.
39. Hydraulic Motor – This hydraulic motor drives the roller
during operation.
40. Rear Drum Zerk Grease Fitting – Grease this fitting
32. Hydraulic Motor – This hydraulic motor controls the
bi-weekly. See maintenance section of this manual.
rotation of the vibratory system.
42. Hand Rail – Grab hold of this hand rail when lifting
33. Bunjee Latch – Pull this rubber latch upward and back
to gain access to the engine/pump compartment.There
is one rubber latch located on each side of the unit.
yourself onto the operator's platform.
PAGE 20 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ENGINE COMPONENTS
Figure 6. B&S 850D Diesel Engine Controls and Components
INITIAL SERVICING
The engine (Figure 6) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturer's engine
manual for instructions & details of operation and servicing.
12. Injector Pump– Provides fuel under pressure to the
injector nozzles.
14. Air Filter – Prevents dirt and other debris from entering the
fuel system. Unsnap air filter cover to gain access to filter
element.
1.
Thermostat – Regulates the temperature of the engine
coolant.
2.
Oil Filler Cap – Remove to add engine oil.
3.
Starter – Starts engine when ignition key is rotated to the
"ON" position
WARNING - BURN HAZARD
4.
Oil Pan– Holds a maximum of 3.5 quarts (3.3 liters) of
motor oil.
Enginecomponentscangenerateextremeheat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
5.
Alternator– Provides charge for battery and voltage for
the +12VDC electrical system.
6.
Injection Nozzle – Injects diesel fuel into the cylinder.
7.
Glow Plugs – Heating element used for starting the engine
in cold weather conditions.
Operating the engine without an air filter,
with a damaged air filter, or a filter in need of
replacement will allow dirt to enter the
engine, causing rapid engine wear.
8.
Oil Drain Plugs – Remove to drain crankcase oil. Fill with
recommended type oil as listed in Table 4.
9.
Oil Filter – Spin-on type, filters oil contaminants.
10. Oil Dip Stick – Remove to check amount and condition of
oil in crankcase. Refill or replace with recommended type
oil as listed in Table 4.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — INSPECTION
3. Check the oil level shown on the dipstick (Figure 8).
Before Starting
1. Read safety instructions at begining of manual.
2. CleantheROLLER,removingdirtanddust,particularlythe
engine cooling air inlet, carburetor and air cleaner.
3. Check theair filter for dirtanddust. Ifairfilterisdirty,replace
air filter with a new one as required.
4. Check carburetor for external dirt and dust. Clean with dry
compressedair.
5. Checkfasteningnutsandboltsfortightness.
Engine Oil Check
1. Tochecktheengineoillevel,placethe rolleronsecurelevel
ground with the engine stopped.
Figure 8. Engine Oil Dipstick
2. Remove the dipstick from its holder (Figure 7) and wipe it
clean.
4. If the oil level is low, remove the oil filler cap (Figure 9) and
filltothesafeoperatinglevel(F)asindicatedbythedipstick.
Pour oil slowly. Fill with recommended type oil as listed in
Table 4.Maximum oil capacity is 3.5 quarts (3.3 liters).
Figure 7. Engine Oil Dipstick (Removal)
Table 4. Motor Oil Grade
Figure 9. Engine Oil Filler Port
Grade of motor oil
Season or Temperature
To assure proper venting, always remove the
dipstick when adding oil. ALWAYS be sure to
check the engine oil level prior to starting the
engine.
(higher than MS class)
Spring, Summer or Autumn
SAE 30
+120° F to +15° F
Winter
SAE 30
+40° F to +15° F
Below +15° F
SAE 10W-30
PAGE 22 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — INSPECTION
4. Ifthefuellevelislow, removethefuelfillercap/guageand
fill with #2 diesel fuel. Wipe up any spilled fuel immedi-
Fuel Check
DANGER - EXPLOSIVE FUEL
ately
.
5. Payattentiontothefueltankcapacitywhenreplenishing
fuel (Figure 12). Refer to the fuel tank capacity listed on
page 13, AR13D Roller Specification Table 1.
NEVER fill the fuel tank while the engine is running or in
the dark. Fuel spillage on a hot engine can cause a fire
or explosion. If fuel spillage occurs, wipe up the spilled
fuel completely to prevent fire hazards.
DO NOT smoke while refueling, motor fuels are highly
flammable and can be dangerous if mishandled.
Figure 12. Adding Fuel
1. Tochecktheenginefuellevel,placethe rolleronsecurelevel
ground with the engine stopped.
6. Afterreplenishingfuel,makesurefuelcapissecurelytighten
to fuel tank. Return operator's seat to normal operating
position.
2. Tilt the operator's seat (Figure 10) forward to gain access
to the fuel tank.
Hydraulic Oil Check
1. To check the hydraulic oil level, place the roller on secure
level ground with the engine stopped.
2. Visually inspect the hydraulic oil sight glass (Figure 13)
located on the right rear of the front drum. For normal
operation the hydraulic oil level must be below the top and
above the bottom of the sight glass. DO NOT OVERFILL!
Figure 10. Fuel Tank Access
3. Readthefuelgauge(Figure11)locatedontopofthefueltank
to determine if fuel level is low.
Figure 13. Hydraulic Oil Sightglass
4. If the hydraulic oil level is low, remove the hydraulic oil cap
(Figure14)andfillwithtypeISO46anti-weartypehydrau-
lic oil to the recommended operating level.
Figure 11. Fuel Guage
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — INSPECTION
Battery Check
A 12-volt DC battery (Figure 16) is shipped dry, and will require
a proper electrolyte level for operation.
ALWAYS be sure that the battery cables are properly
connected to the battery terminals as shown below.Generally
the RED cable will be connected to the positive terminal of
the battery, and the BLACK cable will be connected to the
negative terminal of the battery.
Figure 14. Hydraulic Oil Reservoir Filler Port
Figure 16. Battery
Water Tank Check
WARNING - Battery Polarity Safety
1. To check the water tank water level, place the roller on
secure level ground.
If the battery cables are connected incorrectly, electrical
damage will occur causing damage to the roller's electrical
circuits. Pay close attention to the polarity of the battery
when connecting the battery.
2. The amount of water inside the water tank can be visually
inspected by reading the water tube (Figure 15) that runs
verticallyalongthewatertankattherearoftheroller.Thistube
indicatestheamountofwaterinsidethewatertank.Totaltank
capacity is 40 gallons (152 liters)
WATER
TANK
CAP
WATER
TANK
WATER
LEVEL
TUBE
REAR
ROLLER
Figure 15. Water Tank
PAGE 24 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — INITIAL START-UP
Initial Start-up Instructions
Starting
PUSH-IN, THEN PULL
TO SET THROTTLE
(RPM’s)
CAUTION - General Operation Safety
DO NOT attempt to operate the roller until the Safety, General
Information and Inspection sections have been read and
understood.
1. Placeyourfootintotheroller'sfootstep,grabholdofthehand
raillocatedonthesteeringconsole,andliftyourselfontothe
platform.
THROTTLE RELEASE
AND IDLE BUTTON
PUSH ALL THE WAYDOWN
TO IDLE ENGINE
THROTTLE LOCK
KNOB, TURN CLOCKWISE
TO LOCK THROTTLE CABLE.
2. Sit down in the operators seat and adjust the seat for a
confortable position, then fasten the seat belt (Figure 17)
aroundyourwaist.NEVER!operatetherollerwithouttheseat
beltbeingfastened,seriousinjurycouldoccuriftheseatbelt
is not used.
Figure 19. Throttle Control
6. Insert ignition key into ignition switch (Figure 20), turn key
clockwise until glow plug indicator light turns ON, keep key
in this position until glow plug indicator light turns OFF.
Continue turning ignition all the way clockwise until engine
starts,releasekey.
Figure 17. Securing Seat Belt
3. Beforestartingengine,makesuretheimmediateareaisfree
of obstructions and debris that may lay in the roller's path.
4. Makesurethat theroller'sshiftlever(Figure18)isplacedin
the neutral position.
Figure 20. Ignition Switch
7. Iftheenginedoesnotstart,repeatsteps1through7 orconsult
the troubleshooting guide contained in this manual.
Figure 18. Shift Lever
8. Let the engine warm for 3 to 5 minutes before using roller.
Check for fuel and oil leaks, and noises that would asso-
ciate with a loose guard and/or covers.
5. PUSH the"RED" button(Figure19)onthethrottlecontroland
pulltheroundblackknobabouthalfwayout.Makesurethat
the throttle lock knob has been dis-engaged.
9. If necessary return the choke knob to the full OPEN
position.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — OPERATION
OPERATION
3. Try manuvering the roller a few times to get familar with the
handling. Alsoplacethetravelleverintheopositedirection
to get acquainted with driving in reverse.
Parking Brake
1. To release the parking brake, press and hold the release
button (Figure 21) pull up slightlyon the parking lever, then
push the parking brake lever all the way down.
4. Makesurethattherollercomestoacompletestop(neutral)
beforeplacingthetravelleverineitheraforwardorreverse
position.
Vibration Button
1. To begin the vibratory action, press the vibratory
pushbutton switch located on top of the travel lever as
shown in Figure 23. The pressing of this switch will
generate 3,100 lbs. (1,406 Kg.) of centrifugal force at a
frequencyof4000vpm(vibrationsperminute)tothefront
drum.
Figure 21. Brake Release Lever
Shift Lever
1. To make the roller move in a forward direction, move the
shift lever forward as shown in Figure 22.
Figure 23.Vibration Pushbutton Switch
2. Tostopthevibratoryaction, pressthevibratorypushbutton
switchagain.
Sprinkler Controls
1. Iftheapplicationrequiresthewetting ofasurface,frontand
rear drum sprinkler controls have been provided. These
controls (Figure 24) are located to the bottom right of the
operatorsseat.Thefrontvalve controlsthewatersupplyto
the front drum spray bar and the back valve contols water
flow to the back drum spray bar.
Figure 22. Shift Lever
2. Remember the speed of the roller is directly proportional to
the amount of pressure being applied to the lever in each
direction.Travel speed is between 0 and 4.8 mph (7.2 kph).
FRONT
BACK
CAUTION - Drive System Safety
ALWAYS allow the roller to come to a complete stop before
changing the direction of travel. Changing directions before
the roller comes to a complete stop will result in excessive
force being applied to the transmission and drive system,
which will reduce the over service life of the system.
Figure 24. Sprinkler Controls
PAGE 26 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Maintenance
Perform roller maintenance as
indicated by Figure 25 and
Table 5.
Figure 25. Roller Maintenance
Schedule
Table 5. AR-13H Roller Maintenance Schedule
Daily
1
X
X
X
X
X
X
X
2
X
X
X
X
3
Interval
Notes
1
2
3
4
5
6
7
Engine Oil Level
Water Tank Level
Fuel Level
See Table 4
Hydraulic Oil Level
Sprinkler System
Scraper
Use ISO 46 Type Hydraulic Oil
Replace when badly worn
X
X
Drums (Front/Rear)
Weekly
8
9
Air Filter
Replace paper element once a year.
X
X
X
X
Battery Liquid Level
Bi-Weekly
80 hrs. or
Bi-Weekly
Use Type Alvania #2 or equivalent
3 shots max. DO NOT over grease.
X
10
Zerk Grease Fitting (Rear Drum)
3 Months
Hydraulic Oil Filter (Return)
6 Months
12
13
500 hrs.
Replace with same type filter.
X
X
Engine Oil Filter
20 hrs. or
1 month
After first 20 hrs, change oil filter
every 6 months or 100 hrs.
Yearly
14
Hydraulic Oil
1,100 hrs. or Use ISO 46 Type Hydraulic Oil
0nce a year
X
1 = Check 2 = Refill/ Clean / Grease 3 = Replace
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Hydraulic Oil System
The hydraulic system consists of a two pump stack directly
coupled to the engine. A hydraulic valve block (manifold)is
provided for quick and easy testing and troubleshooting.
Hydraulic oil is filtered by a screen filter located in the tank filler
neck, a 40 micron suction filter located in the tank, and a 10
micron return filter, with cold oil bypass valve located in the
return circuit.
It is recommended that ISO 46 type hydraulic oil or equivalent
be used when adding or replacing the hydraulic oil is required.
DO NOT USE MULTI-VISCOSITY OIL. Cleanliness is a very
important part of proper hydraulic system operation. Hydraulic
oil is not only used to transfer power; it also lubricates and cools
the system components. Keeping the hydraulic system clean
can help reduce costly repairs.
The hydraulic oil level sight glass is located on the right rear of
the front drum, below the engine compartment.This level should
be checked daily.Oil must be below the top and above the bottom
of the sight glass.DO NOT OVERFILL! Care should be taken to
clean the filler cap before adding oil to the system. If hydraulic oil
has to be added, the machine should be inspected for leaks.
Figure 26. Hydraulic Filter Locations
Changing Hydraulic Oil and Filters
1.
Park the roller on a clean flat work area and set the parking
brake.
The suction filter (Figure 26) is located inside the hydraulic
tank.This filter is attached to the fitting connected to the hydraulic
pump suction hose.
2.
Remove the hydraulic oil drain plug (Figure 26) and
drain the hydraulic oil. Dispose of the used oil in an
environmentally friendly manner. Replace the drain plug
and tighten.
The return filter (Figure 26) is located at the front of the engine
compartment.Replace both filters according to theTable 5.
3.
4.
Remove the return filter and install a new filter.Dispose of
the used filter in an environmentally friendly manner.
CAUTION - HYDRAULIC SYSTEM HAZARD
Disconnect the suction hose and remove the fitting from
the tank. Replace the suction filter. Dispose of the used
filter in an environmentally friendly manner. Replace the
fitting and reconnect the suction hose.
DO NOT open hydraulic lines or loosen hydraulic fittings
while engine is running! Hydraulic fluid under pressure can
penetrate the skin, blind, cause burns or create other
potentially dangerous hazards follow all safety instructions
as described throughout this manual.
Freewheel Engagement Valve
This hydraulic system has a freewheel engagemet valve allowing
hydraulic oil to be bypassed. Open (turn allen wrench counter-
clockwise) this valve (Figure 27) to engage the freewheel
capability of the roller. When the valve is fully opened, ports A
and B are allowed to connect, bypassing the oil to and from the
drum drive motors.
Remember the freewheel engagement valve should only be
used in emergencies when the roller cannot be driven due to
engine or hydraulic system problems.
When towing of the roller has been completed, this valve must
be closed (turn allen wrench fully clockwise) completely and
the lock nut set.Failure to close this valve completely will result
in low power, improper speed, and excessive hydraulic oil
temperature.
PAGE 28 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
The vibration circuit is controlled by an electric control valve
located on the valve block (manifold).This valve is controlled by
CAUTION - Freewheel EngagementValve
the “ON/OFF” pushbutton switch mounted on top of the travel
The freewheel engagement valve (towing) is only for
emergency use. DO NOT move roller over 2 MPH or long
distances as hydraulic system component failure could result.
lever.
High-pressure oil is supplied by the pump to the
valve block (port P) and is directed to the electric
control valve. When the pushbutton switch is in the
“OFF” position, this valve is open allowing oil to go
to the steering valve, without driving the vibration
motor.
PUSH
TO
START
ALLEN
WRENCH
CLOSED
(ON)
OPEN
PUSH
TO
START
When the switch is in the “ON” position, the
electric control valve closes and oil is directed
out of port 1 to the vibration motor. Return oil
from the motor returns to the valve block via port
2 and is directed to the steering valve.
CLOSED
FREEWHEEL
ENGAGEMENT
VALVE
CLOSED
(ON)
Steering is controlled by a steering valve and cylinder (Figures
29 and 30).The steering wheel is direct coupled to the steering
valve controling the oil flow to the cylinder.Oil supplied from the
vibration circuit is directed to port 3 which connects to port P of
the steering valve. When steering is not being used, oil passes
out of portT of the valve block and returns to the hydraulic tank.
When the steering wheel is operated, the steering valve closes
and oil is directed to ports L or R to extend or retract the steering
cylinder.
Figure 27. Freewheel EngagementValve
Drum Drive
The drum drive circuit is a parallel, closed loop system
(Figures 29 and 30) consisting of a hydrostatic pump, two
relief valves, a freewheel engagement valve, front and rear
drum drive motors.
The hydrostatic pump is manually controlled by a cable
connected to the forward/reverse shift lever located on the right
side of the operator seat. When the shift lever is placed in forward,
high-pressure oil is supplied by the hydrostatic pump to the valve
block (port A). The valve block (manifold) directs this high-
pressure oil to the front and rear drum drive motors. Return oil
from the motors is returned to the valve block (port B) and is
returned to the suction side of the hydrostatic pump.
Rubber Scrapper Mat
Rubber scraper mats have been provided for the cleaning of the
front and rear drums. Adjust the scrapers mats as close as
possible to the drums, using the slotted holes (Figure 28)
provided. Replace these rubber mats when they become badly
worn.
When shifted into reverse, the high-pressure and suction ports
on the hydrostatic pump are reversed. Oil flow is then in the
opposite direction of forward (port B becomes high-pressure
and port A becomes suction)
Vibration and Steering
The vibration and steering system is an open loop circuit
operated by a gear type pump. Separate relief valves control
each circuit.This system consist of the gear pump, relief valves,
electric vibration control valve, vibration drive motor, steering
valve, and steering cylinder.
Figure 28. Scraper Bar Adjustment
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Forward/Reverse Hydraulic Pressure Test
1.
On the manifold block install a 5,000 psi pressure gauge to
quick disconnect test port 1.
Park the machine on a solid flat surface and stop the engine. Set
the parking brake and block the front drum securely.
2.
3.
Start the engine and run at full throttle.
1.
Check hydraulic oil level by viewing the hydraulic oil sight
glass. The hydraulic oil level must be below the top and
above the bottom of the sight glass. DO NOT OVERFILL!
To start the vibration, press the pushbutton switch
(vibration control) located on top of the travel lever. Under
normal operating conditions this pressure will range
between 800-1,000 psi.
2.
3.
Adjust engine RPM (3,500 +/- 50 RPM)
Let engine run for 5 minutes, this will bring the hydraulic oil
operating temperature to a minimum of 135
Vibration relief pressure is hard to read
accurately using this test. It may be necessary to
disconnect the pressure line to the vibration drive
motor.Plug this line and re-test, pressure will be
exact relief pressure. DO NOT perform this test
for a long period of time — damage could occur.
°
farenheit.
4.
5.
Check and repair all hydraulic leaks.
On the manifold block install a 5,000 psi pressure gauge
(Figure 34) to the forward pressure quick disconnect
test port 2
6.
7.
Run engine at full throttle.
Move the travel lever to the forward position. MAKE SURE
FRONT AND REAR DRUMS DO NOT SPIN.
Steering PressureTest
1.
On the manifold block, install a 5,000 psi pressure gauge
into quick disconnect test port 1 (Figure 34).
8.
9.
Read the pressure gauge. The relief pressure (roller
drums blocked) will read 2,900 145 psi. Under normal
operating conditions this pressure will read 400-600 psi.
2.
3.
Start the engine and run at full throttle.
Turn the steering wheel to the left or right (maximum) and
hold.Read the steering relief pressure.The relief pressure
reading for the steering test port 1 will be 700 psi. Again,
under normal operating conditions, pressure for the
steering port will be between 200-400 psi.
Return the travel lever to the neutral position and stop the
engine.
10. Install the pressure gauge into the reverse quick disconnect
port 3 and repeat the above procedures.The relief pressure
reading for the reverse test port 3 will be the same (2,900
psi). Again normal operation pressure for the reverse port
will be 400-600 psi.
If maximum pressure cannot be reached, plug the steering
cylinder pressure hoses and re-test. If pressure is correct the
steering cylinder is leaking. DO NOT ACTIVATE THE
VIBRATION FUNCTIONWHILE PERFORMINGTHISTEST !
Vibration Circuit PressureTest
Place the front drum on soil, gravel, or a heavy rubber mat.
DO NOT ACTIVATE VIBR
OR HARD SURFACE!
TEST PORTS
1.
2.
3.
Vibration and Steering
Forward
Reverse
Figure 34. ManifoldTest Ports
PAGE 30 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Forward/Reverse ReliefValves Drive Adjustment
Steering ReliefValve Pressure Adjustment
The forward and reverse relief valves (Figure 35) are shim
type cartridge type and are located in the hydrostatic pump (not
on the manifold block) under plugs 1 and 2 . Plug 2 is located in
the same location as plug 1, except it is on the bottom side of the
pump. Relief valve 1 is reverse and 2 is forward.
To adjust the relief valve steering pressure perform the following:
1.
Insert an 8 mm allen wrench into steering relief port 4
(Figure 36) on the manifold block.
2.
On the manifold, connect at 5,000 psi pressure gauge into
quick disconnect test port 1.
Axle Pumps supplied after 01/01/2003 DO NOT
have adjustable relief cartridges.The pressure
is fixed at 2,900 145 psi. If the relief pressure is
not within normal range, the complete cartridge
must be replaced.
3.
4.
Start the engine and run at full throttle.
Turn the steering wheel to the left or right (maximum) and
hold. Read the steering relief pressure.The relief pressure
reading for the steering test port 1 will should be 700 psi.
5.
If the steering relief pressure is not 700 psi, using the allen
wrench adjust the pressure at port 4 until the pressure
gauge reads 500 psi.
1.
2.
3.
4.
Clean the area around the cap.
Remove the cap.
Carefully remove the valve cartridge.
Using an allen wrench, remove the top nut (extreme care
must be taken not to loosen existing shims, spring, or valve)
Add or remove shims as required. Adding shims increases
pressure; removing shims lowers pressure. One shim is
equal to approximately 50 psi. Shim P/N is 34538.
5.
Install the top nut and install valve in the pump cavity using
extreme care not to bind.
6.
7.
Install the valve cap.
Re-test pressure, further adjustment may be needed if
pressure is not correct.
Figure 36. Steering andVibration ReliefValves
Vibration ReliefValve Pressure Adjustment
1.
Insert an 8 mm allen wrench into steering relief port 5
(Figure 36) on the manifold block.
2.
On the manifold block, insert a 5,000 psi pressure gauge
into quick disconnect test port 1.
3.
4.
Start the engine and run at full throttle.
To start the vibration, press the pushbutton switch
(vibration control) located on top of the travel lever. The
relief pressure should read 800 ~ 1,000 psi.
5.
If the vibration relief pressure is not 800 ~ 1,000 psi using
the allen wrench adjust the pressure at port 5 until the
pressure guage reads correctly.
Figure 35. Adjusting Forward/Reverse
ReliefValves
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Removing and Replacing Hydrostatic Pump
Drums and Main Frame
1.
2.
3.
4.
5.
6.
7.
8.
Set the parking brake.
The front drum is designed to apply vibration and compaction
force to the operating surface for compaction.This vibration and
compaction force is produced when the vibrator shaft is rotated.
Maximum efficiency is achieved only when the engine is operated
Disconnect the battery.
Clean the pump and all connections.
Mark and disconnect all hoses and lines from the pump.
Disconnect the forward / reverse control cable.
Disconnect the pump support bracket.
at full throttle.
A single drive motor is mounted on the left side of the drum and
is shockmounted. This type of drive motor is designed for
maximum torque and power.
Remove the engine mounting bolts.
The vibrator is driven by a gear motor coupled to the vibrator
shaft.The vibrator assembly rotates inside of a sealed housing
containing oil to lubricate the bearings.This side of the drum is
also shock mounted.
Elevate the pump and engine assembly using a proper
lifting device.
9.
Disconnect and remove the hydrostatic pump assembly.
10. Repair or replace the hydrostatic pump as required.
Front and Rear Drum Removal and Disassembly.
11. Install the hydrostatic pump in the reverse order of removal,
using Locktite 271 on all mounting bolts and nuts.
The removal and disassembly of the front and rear drums shall
be referenced by Figures 37, 38, and 39 on the following pages.
When reassembling the front drum use Loctite 271 on all
mounting hardware.
12. Test operate.Test and adjust the forward and reverse relief
pressures as required. Adjust the forward / reverse control
cable.
Removing and ReplacingVibration/Steering Pump
1.
2.
3.
4.
5.
Remove the hydrostatic pump as per preceding instructions.
Remove all hoses and lines.
Disconnect the vibration / steering pump and remove.
Repair or replace pump as required.
Install the pump in the reverse order of removal, using
Locktite 271 on all mounting bolts and nuts.
6.
Test operate. Test and adjust the forward and reverse
pressure relief valves as required. Adjust the forward/
reverse control cable. Test and adjust the vibration and
steering pressure relief valves as required.
PAGE 32 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Figure 37. Front-Right Drum Removal
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
STEP 1
STEP 4
M
N
STEP 3
STEP 2
1. JACK FRAME UP SLIGHTLY AT
ARTICULATION JOINT.
3. MARK AND DISCONNECT
HOSES FROM MOTOR.
2. REMOVE THE EIGHT ALLEN HEAD
SCREWS HOLDING THE SIDE
COVER OF THE DRUM SUPPORT
PLATE.
4. REMOVE FOUR ALLEN HEAD
SCREWS FROM DRUM SUPPORT
PLATE. (SCREWS MAY NEED TO BE
HEATED TO REMOVE)
5. PULL DRUM SUPPORT PLATE
OFF DRIVE PLATE ASSEMBLY.
6. REMOVE FOUR ALLEN HEAD
SCREWS SECURING MOTOR TO
DRUM SUPPORT PLATE AND
SET ASIDE.
7. REMOVE SIX NUTS SECURING
DRIVE PLATE TO SHOCK MOUNTS.
PULL OFF DRIVE PLATE AND SET
STEP 6
ASIDE.
STEP 9
STEP 5
STEP 7
STEP 8
8. UN-THREAD SIX SHOCK MOUNTS
FROM DRUM WALL TO REPLACE.
STEP 8
DRUM
9. PULL EXCITER ASSEMBLY TO
REMOVE FROM DRUM INTERIOR.
FRONT
10. REVERSE PROCEDURES TO
REASSEMBLE DRUM. USE
LOCKTITE ON ALL NUTS AND
BOLTS.
Figure 38. Front-Left Drum Removal
PAGE 34 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
STEP 6
STEP 4
STEP 2
I
STEP 5
J
STEP 1
STEP 3
STEP 4
1. JACK FRAME UP SLIGHTLY AT
ARTICULATION JOINT.
4. REMOVE ALLEN HEAD SCREWS
HOLDING THE SIDE COVER OF THE
DRUM SUPPORT PLATE.
2. REMOVE THE FOUR ALLEN HEAD
SCREWS SECURING THE DRUM
SUPPORT PLATE TO THE FRAME.
5. MARK AND DISCONNECT
HOSES FROM MOTOR.
3. REMOVE NUTS SECURING BEARING
FLANGE TO BASE OF DRUM SUPPORT
PLATE.
6. REMOVE FOUR ALLEN HEAD
SCREWS FROM DRUM SUPPORT
PLATES.
7. REMOVE TWO NUTS SECURING
DRUM SUPPORT PLATE TO FLANGE.
PULL OFF LEFT DRUM SUPPORT
PLATE AND SET ASIDE.
8. PULL FLANGE OFF DRUM ROD
FOR SERVICE.
STEP 10
9. PULL RIGHT DRUM SUPPORT PLATE
OFF DRIVE PLATE ASSEMBLY.
STEP 9
STEP 11
10. REMOVE FOUR ALLEN HEAD
SCREWS SECURING MOTOR TO
DRUM SUPPORT PLATE AND
SET ASIDE.
11. REMOVE SIX BOLTS SECURING
DRIVE PLATE TO DRUM WALL.
PULL OFF DRIVE PLATE AND SET
ASIDE.
STEP 8
STEP 7
12. REVERSE PROCEDURES TO
REASSEMBLE DRUM.
Figure 39. Rear Drum Removal/Installation
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MAINTENANCE
Alternator/Regulator
The AR13D is equipped with a 40 amp charging system.This
system uses three charge coils connected in parallel. The
windings of each coil are wound with heave-duty insulated wire
and are further protected by insulating material for long life. A
voltage regulator is provided to control the amount of charge
voltage being delivered to the 12 volt electrical system. For
servicing this charging system, contact your engine dealer.
Neutral Safety Switch
The travel lever is provided with a neutral safety switch
(Figure 40) that prevents the engine from starting when the
lever is in the forward or reverse drive position. Lever must
be placed in the neutral position in order for the starter to
function.
Figure 41. Vibration Solenoid
Battery
Mishandling of the battery shortens the service life of the battery
ans adds to maintenance cost. When handling the battery do the
following:
To check this switch, remove the panel located below and to the
rear of the floor. This switch is mounted to the lower forward/
reverse lever mechanism. Disconnect the white and green wires.
Place the lever in neutral and test for continuity.Place the lever
in forward or reverse; no continuity should be present. Repair or
replace as required.
Be careful not to let the battery electrolyte come in
contact with your body or clothing.
Always wear eye protection and rubber gloves, since
the battery contains sulfuric acid which burns skin and
eats through clothing.
CAUTION - BATTERY ACID BURN HAZARD
If your clothing or skin comes in contact with the battery acid,
immediately wash off with running water and get medical
attention.
Check the battery regulary and make sure that each
electrolyte level is to the bottom of the vent well
(Figure 42). If necessary add only distilled water in a
well-ventilated area.
Figure 40. Safety Switch
Vibrator Solenoid
The vibrator solenoid (Figure 41) is located in the manifold valve
block and is controlled by the vibration switch located on top of
the travel lever.This solenoid controls the vibration control valve
which supplies hydraulic oil to the vibration drive motor.
To test the vibration solenoid, turn the ignition switch on. Check
for proper supply voltage and ground. If proper voltage and
ground are present, check the solenoid for continuity. If no
continuity, replace the solenoid coil.If continuity is present, place
your hand on the solenoid and turn the switch to the ON position;
movement should be felt. DO NOT STARTTHE ENGINE FOR
THISTEST
Figure 42. Battery Fluid Levels
PAGE 36 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — PREPARATION FOR LONG-TERM STORAGE
Roller Storage
For storage of the roller for over 30 days, the following is
recommended:
Drain the fuel tank completely, or add STA-BIL to the
fuel.
Run the engine until the fuel in the injection system is
completely consumed.
Completely drain used oil from the engine crankcase
and fill with fresh clean oil, then follow the procedures
described in the engine manual for engine storage.
Drain water tank
Clean the entire roller and engine compartment.
Remove battery and store it in cool dry place.
Cover the roller and place it a clean dry area, that is
protected from harsh elements.
Remove ignition key, and store in a safe place.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MANIFOLDTEST PORTS
Figure 29. ManifoldTest Ports
PAGE 38 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HYDRAULIC SYSTEM DIAGRAM
Figure 30. Hydraulic System Diagram
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D ROLLER — ELECTRICWIRING DIAGRAM
Wiring diagram not available at this time.
PAGE 40 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HYDRAULIC HOSE CONNECTIONS
MANIFOLD
FROM OPERATOR’S
FRONT RIGHT SIDE
POSITION
H
C
G
F
B
G
A
E
D
B
A
F
C
FRONT LEFT SIDE
FROM OPERATOR’S
POSITION
D
E
HYDRAULIC
DRIVE PUMP
NOTES
HOSES SHADED FOR
VISUAL CLARITY.
Figure 32. Hydraulic Hose Connections 1
PAGE 42 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HYDRAULIC HOSE CONNECTIONS
FRONT RIGHT MOTOR
Q
STEERING COLUMN
O
O
P
Q
K
L
P
MANIFOLD
K L
N
M
I
J
REAR LEFT MOTOR
FROM OPERATOR’S
POSITION
J
I
N
M
NOTES
FRONT LEFT MOTOR
HOSES SHADED FOR
VISUAL CLARITY.
Figure 33. Hydraulic Hose Connections 2
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —TROUBLESHOOTING (ROLLER)
TABLE 6. ROLLER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Low engine RPM?
SOLUTION
Check and adjust engine speed.
Low Vibration
Low hydraulic pressure?
No voltage to 12 volt solenoid?
No oil pressurel?
Check and adjust hydraulic pressure.
Check vibration switch, check coil for continuity.
Check for proper oil pressure or defective relief valve.
Replace coupler.
No Vibration
Broken motor coupler?
Low hydraulic pressure?
Steering column connector?
Defective steering cylinder?
Defective Steering cylinder?
Low hydraulic pressure?
Check pressure.
Slow Steering
Inspect bearings and grease if necessary.
Check seals, replace if necessary.
Inspect cylinder for contamination, replace if necessary.
Check pressure.
Steers Slow in One Direction
Rubber scrapper adjustment
incorrect?
Check for proper adjustment against drum.
Slow Forward/Reverse Speed
Main Hydraulic Pressure Low
Rubber shock mount loose?
Inspect for broken mount, replace if necessary.
Close valve.
Free wheel valve "open"?
Speed control cable out of
adjustment?
Inspect cable and adjust if necessary.
Incorrect engine speed?
Adjust engine speed to correct speed.
Inspect for cracks, replace if necessary.
Broken rubber shock mounts or
drive plate?
Drive motor hardware not
secure?
Check motor nut and key coupler.
PAGE 44 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTON
POSSIBLE PROBLEM
No Fuel reaching injection pump?
Defective fuel pump?
SOLUTION
Add fuel. Check entire fuel system.
Replace fuel pump.
Fuel filter clogged?
Replace fuel filter and clean tank.
Replace or repair fuel line.
Faulty fuel supply line?
Engine will not start or start is
delayed, although engine can
be turned over.
Check piston, cylinder and valves. Adjust or
repair per engine repair manual.
Compression too low?
Fuel pump not working correctly?
Oil pressure too low?
Repair or replacefuel pump.
Check engine oil pressure.
Comply with cold starting instructions and
proper oil viscosity.
Low starting temperature limit exceeded
Defective battery?
Charge or replace battery.
Refill engine crankcase with correct type of oil
for winter environment.
Engine oil too thick?
At low temperatures engine will
not start.
Defective battery?
Fuel filter blocked?
Fuel supply blocked?
Defective fuel pump?
Fuel tank empty?
Replace battery.
Replace fuel filter.
Check the entire fuel system.
Replace fuel pump.
Add fuel.
Engine fires but stops soon as
starter is switched off.
Fuel filter blocked?
Defective fuel pump?
Replace fuel filter.
Replace fuel pump.
Engine stops by itself during
normal operation.
Mechanical oil pressure shutdown sensor
stops the engine due to low oil?
Add oil. Replace low oil shutdown sensor if
necessary.
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —TROUBLESHOOTING (ENGINE)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTON
POSSIBLE PROBLEM
Fuel tank empty?
SOLUTION
Replace fuel filter.
Replace fuel filter.
Fuel filter clogged?
Fuel tank venting is inadequate?
Leaks at pipe unions?
Ensure that tank is adequately vented.
Low engine power, output and
speed.
Check threaded pipe unions tape and tighten
unions a required.
Speed control lever does not remain in selected See engine manual for corrective action.
position?
Engine oil level too full?
Air filter blocked?
Correct engine oil level?
Clean or replace air filter.
Adjust valves per engine specification.
See engine manual.
Low engine power output and
low speed, black exhaust
smoke.
Incorrect valve clearances?
Malfunction at injector?
Drain off engine oil down to uppermark on
dipstick.
Too much oil in engine crankcase?
Air-cooled diesel engine runs
very "HOT". Cylinder head
overheats.
Clean cooling air system, and cooling fin
areas.
Entire cooling air system contaminated blocked?
PAGE 46 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
QTY. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SAMPLE PARTS LIST
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
WASHER, 3/8 IN....1 .....MQ-45T ONLY
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLY
BEARING ..............1 .....S/N 2345B AND ABOVE
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
NO. Column
Indicated by:
Unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“Not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
PAGE 48 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SUGGESTED SPARE PARTS
AR13D Ride-onTandem Drum Roller
w/Briggs and Stratton Diesel Engine
1 to 3 Units
Qty.
P/N
Description
1 .......... 513324 ................... Forward Reverse Travel Cable
............ 509350SW ............. Neutral Safety Switch
2 .......... 510229 ................... Throttle Cable
6 .......... 508667 ................... Hydraulic Oil Filter
1 .......... 507278 ................... HydraulicTank Cap
6 .......... 820311 ................... Fuel Filter
1 .......... 34507 ..................... Fuel Tank Cap Gauge
1 .......... 509249 ................... Water Tank Cap
4 .......... 508433 ................... Rubber Drum Scraper
3 .......... M113621 ................ Air Filter Element
4 .......... 691959 ................... Ignition Key
2 .......... 692318 ................... Ignition Switch
4 .......... 821075 ................... Fan Belt
4 .......... 820150 ................... Rocker Cover Gasket
6 .......... 820314 ................... Engine Oil Filter
2 .......... 820258 ................... Radiator Cap
1 .......... 825222 ................... Starter
2 .......... 821135 ................... Oil Pressure Switch
2 .......... 820208 ................... Water Temperature Switch
2 .......... 825064 ................... Thermostat
2 .......... 515848 ................... Breaker Switch
1 .......... 825324 ................... Injection Pump
1 .......... 825265 ................... Water Pump
1 .......... 825133 ................... Radiator Hose Upper
1 .......... 825134 ................... Radiator Hose Lower
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
1
8
7
9
2
14
15
6
4
26
3
10
13
REAR
ROLLER
5
11
23
17
24
16
12
18
12
12
18
20
20
19
22
21
21
25
18
PAGE 50 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO.
1
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NO.
513457
13118
511726
511736
511740
34536
PART NAME
QTY.
REMARKS
DECAL: STEERING CONSOLE
DECAL: POWDER COATED
DECAL: HYDRAULIC OIL LEVEL INDICATOR
DECAL:WARNING
DECAL: MULTIQUIP BANNER
DECAL: OWNERS MANUAL
DECAL: ENGINE RPM SETTING
DECAL: WATER TANK CAP
DECAL: CONTROL PANEL
DECAL: SERVICE INSTRUCTION CHART
DECAL: SECURING POINT INDICATOR ................ 3 ........ POINT ARROW DOWN
DECAL:CAUTION
DECAL: ATTENTION
DECAL: PARKING BRAKE INSTRUCTIONS
DECAL: AR13D MQ LOGO
DECAL:DANGER
DECAL: SECURING POINT INDICATOR ................ 4 ........ POINT ARROW UP
DECAL: CAUTION STRIPE PATTERN.................... 1 ........ HORIZONTAL PLACEMENT
DECAL: CAUTION STRIPE PATTERN.................... 2 ........ VERTICAL PLACEMENT
1
1
1
1
1
1
1
1
1
1
513580
513698
515436
511737
513393
511735
513707
513467
515818
511738
513393
513469
511718
513688
513740
515815
511739
511724
511733
2
2
1
1
1
DECAL: MQ LOGO
2
DECAL: CAUTION STRIPE PATTERN.................... 1 ........ HORIZONTAL PLACEMENT
DECAL: AR13D MQ LOGO
DECAL:CAUTION:INSTRUCTIONS
DECAL: GREASE REMINDER
DECAL:HYDRAULIC OIL INDICATOR
1
1
1
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — FRONT DRUM ASSY.
FRONT DRUM ASSY.
PAGE 52 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — FRONT DRUM ASSY.
FRONT DRUM ASSY.
NO.
2
4
6
8
PART NO.
513280
506145
506147
506136
508665
506142
011208025
EM923023
492264
506141
508340
020108060
514522
6109210
513283
513314
506220
492362
EM923343
513337
513343
513342
EM963610
3019092
505985
021110120
505977
505984
EM503803
515637
EM924006
511159
515396
505990
515639
505951
513332
PART NAME
QTY.
REMARKS
FRONT ROLLER
HOUSING BEARING
BEARING
RING, RETAINING
COUPLER
MOUNT, VIBRATION MOTOR
BOLT, 8X25T................................................... 6 ................ REPLACES 508342
WASHER, FLAT 5/16” ..................................... 6 ................ REPLACES 492597
1
1
1
1
1
1
10
12
14
16
18
20
22
26
28
30
32
34
36
40
41
43
45
47
78
80
82
84
86
88
90
92
94
95
96
98
100
124
126
128
130
BOLT, 3/8”X1”
SHOCK, MOUNT
STUD, M8X40
6
3
6
NUT, M8 .......................................................... 6 ................ REPLACES 508341
ROLLER, SUPPORT, RIGHT .......................... 1 ................ LEFT SIDE - FRONT/REAR
BOLT 1/2”X1-1/2” ............................................ 8 ................ REPLACES 492276
HOSE, PROTECTION COVER
NUT 1/4”X1/2”
MOTOR, HYDRAULIC
NUT 5/16”X5/8”
WASHER, LOCK 5/16” DIAMETER .............. 10 ................ REPLACES 492623
HOSE
HOSE
HOSE
BOLT 3/8”X1” .................................................. 6 ................ REPLACES 492375
WASHER, 3/8 ................................................. 6 ................ REPLACES 508346
SHOCK, MOUNT
NUT, NYLON LOCK M10 ZINC 1.SP
PLATE, DRIVER
1
12
1
4
1
1
1
6
12
1
HUB
1
PINS, DOWEL ................................................ 2 ................ REPLACES 503803
SUPPORT, ROLLER, LEFT ............................ 1 ................ RIGHT SIDE - FRONT
KEY, COTTER 1/8”X2” .................................... 1 ................ REPLACES 491690
FLAT WASHER
MOTOR, HYDRAULIC
BOLT 1/2”X2-1/2”
COVER
FITTING
FITTING
HOSE
HOSE
1
1
4
1
2
2
1
1
515641
513344
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — EXCITER ASSY.
EXCITER ASSY.
58
46
64
74
66
76
52
70
70
1
60
54
62
74
64
48
NOTES:
46
INNER BEARINGS ARE INCLUDED
WITH ITEM 64.
1
44
PAGE 54 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — EXCITER ASSY.
EXCITER ASSY.
NO.
44
46
48
52
54
58
60
62
64
66
70
74
76
PART NO.
EM963610
3019092
513285
EM927040
492467
EM963610
506144
490964
506131
513418
506135
513286
513287
PART NAME
QTY.
REMARKS
CAPSCREW, 3/8”N X 1-1/4”G5
6
WASHER, 3/8" ............................................... 12 ............... REPLACES 508346
HOUSING, BEARING RIGHT
KEY, WOODRUFF 606 ..................................... 1 ............... REPLACES 506250
SCREW, ALLEN 5/16”
CAPSCREW, 3/8” ............................................ 6 ............... REPLACES 492375
SEAL
RING, RETAINING
1
4
1
1
2
1
2
2
1
BEARING
EXCITER SHAFT
RING, RETAINING
OIL SEAL 65x100x9
HOUSING, BEARING LEFT
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — REAR DRUM & CHASSIS ASSY.
REAR DRUM & CHASSIS ASSY.
PAGE 56 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — REAR DRUM & CHASSIS ASSY.
REAR DRUM & CHASSIS ASSY.
NO.
2
4
PART NO.
513291
505988
PART NAME
REAR DRUM
ALLEN PLUG
NUT, LOCK 1/2 IN.
QTY.
REMARKS
1
1
2
6
492584
8
503735
514523
513283
509165
6109210
EM963610
3019092
505977
3019092
EM963610
505984
EM503803
515637
515639
513314
511159
EM924006
515396
505990
505951
BEARING, FLANGE ........................................ 1 ............... INCLUDES ITEMS W/
SUPPORT, ROLLER ........................................ 1 ............... RIGHT SIDE - REAR
*
10
11
12
14
16
18
20
22
24
26
28
30
32
34
35
36
38
40
66
70
72
HOSE PROTECTION COVER
BOLT, 1/2 NC x 2-1/4 IN. G5
1
2
BOLT, 1/2 NC x 1-1/2 IN. G5 ............................ 8 ............... REPLACES 492276
CAPSCREW, 3/8 IN. NC x 1-1/4 IN. G5
LOCK WASHER 3/8 IN. .................................. 6 ............... REPLACES 508346
PLATE DRIVE
6
1
WASHER 3/8 IN............................................... 6 ............... REPLACES 508346
CAPSCREW, 3/8 NC x 1-1/4 IN. G8 ................ 6 ............... REPLACES 492375
HUB
1
2
PINS, DOWEL 3/8 x 1 IN.
REAR ROLLER SUPPORT, LEFT ................... 1 ............... LEFT SIDE - FRONT/REAR
SUPPORT COVER
BOLT, 1/4 NC x 1/2 IN. G
FLAT WASHER 1 IN.
1
12
1
KEY, COTTER 1/8 x 2 IN................................. 1 ............... REPLACES 491690
MOTOR, HYDRAULIC
BOLT, 1/2 NC x 2-1/2 IN. G
FITTING 8-10-F5OLO-S
HOSE
1
4
2
2
513349
ZERK GREASE FITTING ................................ 1 ............... CANNOT BE SOLD SEPARATELY
ZERK CAP....................................................... 1 ............... CANNOT BE SOLD SEPARATELY
*
74
*
100
126
128
130
132
513266
505976
506185
492367
EM923343
REAR CHASSIS
CLAMP 3/4
PLATE CORNER
SCREW, HHC5/16”-18X1-3/4”
1
5
4
3
WASHER, LOCK 5/16” ..................................... 4 ............... REPLACES 492623
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — COVERS AND FRAME ARTICULATION LOCK ASSY.
PAGE 58 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — COVERS AND FRAME ARTICULATION LOCK ASSY.
COVERS AND FRAME ARTICULATION LOCK ASSY.
NO.
4
6
20
21
22
23
24
27
29
30
32
33
PART NO.
513315
509177
515416
515415
509177
512881
511474
508679
509074
514243
492363
EM923023
EM923343
507888
EM923023
2105164
510875
513314
513471
513328
2101402
492410
506167
EM923023
EM969023
745
PART NAME
REAR WATER TANK COVER
BOLT 5/16 IN.
FLOOR PLATE
ARM, FLOOR COVER
BOLT 5/16 X 3/4 IN.
RIVET AM-54 .................................................. 1 ............... REPLACES 503723
BRACKET, ARM
SEAL RUBBER
PIN COTTER 3/32"
CONSOLE COVER
BOLT 5/16 X 3/4 IN. NCG5
WASHER 5/16" ................................................ 6 ............... REPLACES 505679
WASHER, LOCK 5/16 IN. ................................ 6 ............... REPLACES 492623
QTY.
REMARKS
1
4
1
1
2
1
11.8"
1
1
6
34
136
138
140
142
159
161
162
163
164
166
167
168
170
238
240
242
243
SEAT
1
NUT 5/16" ...................................................... 12 ............... REPLACES 505679
NUT, NYLON 5/16 IN. - 18 ............................... 4 ...............REPLACES 492582
BOLT 3/4 NC X 1-1/2 IN
SCREW 1/4" X 3/4"
LOCK CLIP
4
1
1
1
LOCKING ARM
WASHER LOCK 1/4" ....................................... 1 ............... REPLACES 492622
BOLT 5/8 NC x 2-1/2 IN. G5
WASHER, PLASTIC 5/8 IN.
WASHER, PLAIN 5/16 IN. ............................... 1 ............... REPLACES 506109
NUT, LOCK 5/8 IN............................................ 1 ............... REPLACES 492586
LOCK PIN
DOCUMENT BOX
BOLT 1/4" X 3/4"
1
2
1
1
2
29057
492356
EM923057
492581
WASHER 1/4 IN............................................... 8 ............... REPLACES 492596
NUT 1/4"-20 NYLON
2
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HOOD AND REAR PANEL ASSY.
HOOD AND REAR PANEL ASSY.
PAGE 60 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HOOD AND REAR PANEL ASSY.
HOOD AND REAR PANEL ASSY.
NO.
2
4
6
8
PART NO.
515703
513305
0202
PART NAME
HOOD
HINGE, SLOTTED
QTY.
1
2
REMARKS
SCREW, HHC 5/16 X 18 X 1 IN....................... 4 ............... REPLACES 492364
FLAT WASHER 5/16 IN.................................. 10 ............... REPLACES 505679
NUT, NYLON 5/16- 18 ...................................... 4 ............... REPLACES 492582
LATCH KIT ....................................................... 2 ............... REPLACES 504744
RIVET BRAKE LINING .................................... 2 ............... REPLACES 503723
SEAL RUBBER
SEAL RUBBER
LATCH KIT (HOOD)
BOLT 1/4 X 3/4 IN.
NUT 1/4 IN.
FRONT CHASSIS
REAR EINGINE COVER
GROMMET, 1-1/4 IN. ID
EM923023
2105164
491010
512881
508679
508679
514438
492356
492581
515645
513308
13212
506158
490181
516294
0202
2105164
EM923023
011208025
EM923343
506205
510925
513314
EM506085
10
12
13
15
17
18
22
24
30
32
33
34
90
92
94
96
98
100
102
104
148
150
155
56.1"
23.6"
2
12
12
1
1
1
BOLT 5/16 X 3/4 IN. ........................................ 4 ............... REPLACES 513309
SIGHT GLASS
SUPPORT REAR ENGINE COVER
1
1
BOLT 1/4 X 3/4 IN. .......................................... 1 ............... REPLACES 492364
WASHER, LOCK 1/4 IN. .................................. 1 ............... REPLACES 492622
FLAT WASHER 5/16 IN.................................... 3 ............... REPLACES 492597
BOLT 8 X 25T DCA-85,125,150SSM ............... 1 ............... REPLACES 508342
WASHER, LOCK 5/16 IN. ................................ 1 ............... REPLACES 492623
PLUG
NUT 3/16 IN.
BOLT 1/4 X 1/2 IN.
1
2
2
GROMMET ...................................................... 1 ............... REPLACES 506085
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D — STEERING COLUMN AND HYDRAULIC ARTICULATION ASSY.
STEERING COLUMN AND HYDRAULIC ARTICULATION ASSY.
PAGE 62 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D — STEERING COLUMN AND HYDRAULIC ARTICULATION ASSY.
STEERING COLUMN AND HYDRAULIC ARTICULATION ASSY.
NO.
16
18
19
22
24
26
28
30
PART NO.
EM969023
492413
EM128
506196
513297
6109210
513299
EM963055
6109180
0166A
PART NAME
QTY.
REMARKS
NUT, LOCK 5/8 IN............................................ 2 ............... REPLACES 492586
BOLT 5/8” UNC X 3-1/2
BOLT 5/8"NC X 4"G8
ELBOW FITTING
CYLINDER, STEERING
BOLT 1/2"-13 x 1-1/2 ....................................... 4 ............... REPLACES 492276
COVER, ARTICULATING JOINT
HEX HEAD CAPSCREW 3/8 IN. x 3/4 IN........ 3 ............... REPLACES 492373
WASHER, LOCK 1/2” DIAMETER ................... 8 ............... REPLACES 492626
WASHER, LOCK 3/8” DIAMETER ................... 3 ............... REPLACES 492624
1
1
2
1
1
32
34
36
38
40
42
44
46
48
50
52
54
56
58
172
174
176
178
181
182
184
186
188
190
192
194
195
198
200
202
390
391
513300
513301
506164
6109210
6109180
513302
513303
6109210
491701
513350
513348
491008
509156
493128
507862
506265
513346
EM923343
508335
509190
506186
18706
RETAINER PLATE
SPACER
BEARING
1
1
1
BOLT 1/2 IN. NC x 1-1/2 IN. G ......................... 4 .............. REPLACES 492276
WASHER, LOCK 1/2 IN. .................................. 4 .............. REPLACES 492626
BASE, ARTICULATING JOINT
ARTICULATING JOINT
BOLT 1/2 IN. NC x 1-1/2 IN. G ......................... 4 ............... REPLACES 492276
ZERK FITTING
HOSE, 9
HOSE, 16
GREASE COVER
NUT
WHEEL, STEERING
STEERING COLUMN ...................................... 1 ............... REPLACES 5061861
NUT 5/16 IN.
HOSES K AND L
WASHER 5/16 IN............................................. 4 ............... REPLACES 492623
BUSHING
WASHER 3/4 IN.
HYDRAULIC VALVE
HOUR METER
NUT, LOCK 3/16”
SWITCH, STARTER
KEY, IGNITION
BOLT 1/4 IN. x 3/4 IN.
NUT 1/4 IN. ...................................................... 1 ............... REPLACES 492581
HARNESS, WIRING
INDICATOR, GAUGE, ENGINE STATUS
CIRCUIT BREAKER
1
1
1
1
1
1
1
1
4
2
4
1
1
1
1
1
1
1
503119
692318
691959
492356
EM969079
515791
515971
515848
1
1
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ARTICULATION ARM ASSY.
ARTICULATION ARM
PAGE 64 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ARTICULATION ARM ASSY.
ARTICULATION ARM
NO.
2
4
6
8
10
62
PART NO.
513294
514347
EM505069
513295
513296
PART NAME
ROD END
BOLT 3/4 IN. x 2-1/2 IN.
NUT 3/4 IN.
NUT 3/4 IN.
ROD, DIRECTION STABILIZER
FLAT WASHER 3/4.
QTY.
REMARKS
2
2
2
2
1
4
514433
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HYDRAULIC DRIVE PUMP ASSY.
HYDRAULIC DRIVE PUMP ASSY.
PAGE 66 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — HYDRAULIC DRIVE PUMP ASSY.
HYDRAULIC DRIVE PUMP ASSY.
NO.
36
54
56
58
60
62
64
66
68
70
72
74
PART NO.
515803
507845
EM508346
EM175
507860
506187
513310
509144
2105162
2105164
503119
513489
515727
506217
515723
506207
506203
515725
508427C
515726
508343
513339
508428C
506219
506195
515724
EM923343
515811
PART NAME
ENGINE, BRIGGS AND STRATTON 850D
PUMP, STEERING
QTY.
1
1
REMARKS
WASHER 3/8 IN............................................... 2 ............... REPLACES 508346
BOLT 3/8-16 X 1-1/4 SC HD
ADAPTER, STEERING PUMP
HYDRAULIC PUMP
SHIFT LEVER
BOLT 3/16 X 1-3/4 IN.
BOLT 5/16 X 1-3/4 IN. ..................................... 1 ............... REPLACES 492367
NUT, NYLON 5/16 IN. - 18 ............................... 1 ............... REPLACES 492582
NUT, LOCK 3/16 IN.
SCREW ALLEN HEAD 1/4 - 20 X 3/8 IN. ........ 1 ............... REPLACES 492465
HOSE
FITTING 3/4 IN.
HOSE
HOSE CLAMP, HS-16
FITTING
HOSE
COPPER WASHER 21/32 IN.
HOSE
FITTING
2
1
1
1
1
1
87
2
1
1
2
1
1
3
1
3
1
1
1
1
1
190
191
192
196
199
200
201
202
203
204
206
208
209
388
390
HOSE
COPPER WASHER 5/8 IN.
FITTING 1/2 IN.
FITTING 3703-08-08
HOSE
WASHER LOCK 5/16" .................................... 4 ................ REPLACES 492623
COUPLING, FLYWHEEL ASSY ...................... 1 ................ INCLUDES ITEMS W/#
391# 515811H
HUB, DRIVE
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MANIFOLD AND HYDRAULIC OIL FILTER ASSY.
MANIFOLD AND HYDRAULIC OIL FILTER ASSY.
PAGE 68 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MANIFOLD AND HYDRAULIC OIL FILTER ASSY.
MANIFOLD AND HYDRAULIC OIL FILTER ASSY.
NO.
30
83
87
91
PART NO.
515645
513221
515727
EM505186
507278
506218
506221
508667
508664
492356
2101402
506204
EM25507
506244
508670
505976
506185
2105162
EM923343
492371
506201
506202
506206
506195
515502
508814
506192
507774
507772
506247
506246
506245
507885
506182
506190
511808
506190
506205
506193
PART NAME
CHASSIS AR13D
HOSE
QTY.
REMARKS
1
1
1
HOSE
CUSHION RUBBER ......................................... 2 ............... REPLACES 505186
106
108
110
112
114
116
118
120
121
122
124
126
128
130
132
134
136
138
140
144
156
157
158
160
162
164
166
168
170
172
174
176
178
182
186
HYDRAULICTANK CAP
STRAIGHT FITTING 3/4"
FILTER
OIL FILTER
FILTER, HEAD
1
1
1
1
1
2
BOLT 1/4" X 3/4"
WASHER, LOCK 1/4” ....................................... 2 ............... REPLACES 492622
FITTING
FITTING
BLOCK FILTER M10
VALVE CHECK
CLAMP 3/4
1
2
1
1
3
3
PLATE CORNER
SCREW, HHC5/16”-18X1-3/4” .......................... 2 ............... REPLACES 492367
WASHER, LOCK 5/16” ..................................... 3 ............... REPLACES 492623
BOLT 5/16” LOCK
FITTING, TEE
FITTING
FITTING
FITTING
MANIFOLD
BOLT 5/16”X3-1/4”
FITTING
VALVE RELIEF, 500 PSI
PLUG
VALVE, NEEDLE
VALVE, RELIEF, 2000 PSI
VALVE, SOLENOID
12 VOLT COIL SOLENOID
COUPLING PSI TEST
FITTING
ADAPTER, STRAIGHT
FITTING
PLUG
1
1
1
1
1
1
2
2
1
1
1
1
1
1
3
2
2
2
1
5
FITTING
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — FUELTANK & OIL DRAIN HOSE ASSY.
FUEL TANK & OIL DRAIN HOSE ASSY.
PAGE 70 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — FUELTANK & OIL DRAIN HOSE ASSY.
FUEL TANK & OIL DRAIN HOSE ASSY.
NO.
124
204
205
206
207
208
210
212
213
214
216
218
220
221
248
252
256
268
270
284
285
290
292
294
342
344
346
362
364
398
400
401
402
403
404
405
PART NO.
508302
513329
514467
34507
PART NAME
QTY.
2
1
1
1
5.6'
1
1
REMARKS
PAD, RUBBER TANK
FUEL TANK
BRACKET, FUEL TANK SUPPORT
CAP, FUEL W/GAUGE
PAD, RUBBER BRACKET 4 x 36 x 10 mm
FLEX TUBE 5/16 IN.
ADAPTER, ELBOW
BOLT 3/8 NC x 3/4 IN. G5
WASHER, LOCK 5/16 IN. .......................................2 ......... REPLACES 492623
WASHER, FLAT 3/8 IN.
NUT, HEX 5/16 IN. ..................................................2 ......... REPLACES 492553
514340
505594
514560
492309
EM923343
3019092
2105164
506208
514536
514536
512731
512731
EM512722
511778
514536
491210
505594
514536
EM20427
514536
515697
011208025
EM923343
492363
492582
825219
516416
516417
516353
513619
820311
820347
2
2
CLAMP HS-4
12
4.1'
.7'
2
2
1
2
4.1'
1
1
4.1'
HOSE 4FLH 5/16 IN.
HOSE 4FLH 5/16 IN.
ADAPTOR
ADAPTOR
FUEL SHUT-OFF VALVE
ADAPTER
HOSE 4FLH 5/16 IN.
PLUG, TANK 1/4 IN.
FLEX TUBE 5/16 IN.
HOSE 4FLH 5/16 IN.
HOSE 4FLH 5/16 IN.
HOSE 4FLH 5/16 IN.
FILTER SUPPORT
BOLT 8 X 25T .........................................................2 ......... REPLACES 508342
WASHER 5/16 IN....................................................2 ......... REPLACES 492623
BOLT 5/16" NC X 3/4" G5
4'
4.6'
1
2
2
1
1
1
1
1
1
1
NUT 5/16"-18
FUEL FILTER ASSY W/SENSOR
ENGINE OIL DRAIN
FITTING 90°
HOSE
FITTING
FUEL, FILTER ELEMENT W/O SENSOR
SENSOR, FUEL FILTER
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —WATERTANK ASSY.
WATER TANK ASSEMBLY ASSY.
PAGE 72 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —WATERTANK ASSY.
WATER TANK ASSEMBLY ASSY.
NO.
8
14
PART NO.
513316
509249
PART NAME
QTY.
1
1
REMARKS
WATERTANK
WATER TANK CAP
PLUG
16
514541
1
17
18
491028
506071
CLAMP
ELBOW PVC
10
7
19
84
86
88
506288
513321
EM506085
EM492358
492581
CLAMP
WATER VALVE EXTENSION
GROMMET
BOLT 1/4" NC x 1-1/4" G5
NUT1/4"
1
1
2
4
90
4
92
93
94
513322
513351
513379
VALVE, BALL
ELBOW 90G 1/2” NYLON
“T” ADAPTER
2
1
1
96
98
402010060
506086
3019092
EM20426
508435
EM20415
503015
402010060
402010060
402010060
402010060
402010060
508301
508251
506084
EM923023
EM492299
506072
506074
508610
HOSE 1/2" ....................................................1.3' ............... REPLACES 504163
U- BOLT 3/8"
WASHER, FLAT. 3/8”...................................... 16 ............... REPLACES 492598
4
100
101
102
103
104
116
118
119
120
122
123
125
128
130
132
266
268
270
ELBOW BRASS
LOCK NUT
TUBE 5/16"
2
8
2.3'
2
KNOB, HANDLE ADJ.
HOSE 1/2" .................................................. .33' ................ REPLACES 504163
HOSE 1/2" .................................................. .66' ................ REPLACES 504163
HOSE 1/2" ..................................................... 2' ................ REPLACES 504163
HOSE 1/2" .................................................... .5' ................ REPLACES 504163
HOSE 1/2" .................................................. 6.2' ................ REPLACES 504163
PAD, WATERTANK
PAD, WATERTANK
CLAMP
2
2
4
NUT 5/16" ........................................................ 4 ............... REPLACES 505679
SCREW, HHC 5/16”- 18X1/2” ........................... 4 ............... REPLACES 505401
PVC TUBE
MALE ADAPTER
CAP
4
4
4
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ENGINE MOUNTING ASSY.
ENGINE MOUNTING ASSY.
PAGE 74 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — ENGINE MOUNTING ASSY.
ENGINE MOUNTING ASSY.
NO.
36
PART NO.
515803
515800
492599
492625
PART NAME
QTY.
REMARKS
DIESEL ENGINE, BRIGGS AND STRATTON 850D ...... 1 ..........INCLUDES ITEMS W/#
316
318
319
320
322
324
326
328
330
332
334
336
338
340
450#@
451#@
BOLT 7/16"NC X 1" G5
WASHER 7/16"
WASHER 7/16"
2
2
2
1
515659
MOUNT, ENGINE
EM963057
3019092
EM969013
515650
EM963610
3019092
EM969013
2105162
EM923023
2105164
CAPSCREW 3/8"X1-1/2" ............................................... 2 ..........REPLACES 492313
WASHER FLAT 3/8" ....................................................... 4 ..........REPLACES 492598
NUT NYLOC................................................................... 2 ..........REPLACES 492583
MOUNT, ENGINE
1
CAPSCREW 3/8"NC X 1-1/4" G8 .................................. 2 ..........REPLACES 492376
WASHER FLAT 3/8" ....................................................... 2 ..........REPLACES 492598
NUT NYLOC................................................................... 2 ..........REPLACES 492583
SET BOLT ENGINE ....................................................... 2 ..........REPLACES 492367
WASHER PLAIN 5/16" ................................................... 2 ..........REPLACES 492597
NUT 5/16" ...................................................................... 2 ..........REPLACES 492582
MOUNT, ENGINE
MOUNT, ENGINE
1
1
452# 835034
ENGINE MOUNT KIT .................................................... 1 ..........INCLUDES ITEMS W/@
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 76 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — MUFFLER ASSY.
MUFFLER ASSY.
NO.
212
348
350
352
354
356
358
360
396
412
414
416
418
424
426
428
430
450
PART NO.
506257
515667
515663
493108
PART NAME
U-BOLT
QTY.
REMARKS
1
1
1
2
MOUNT PLATE, MUFFLER
MUFFLER BASE EXTENSION
CLAMP
SCREW, HHC 5/16-18 X 1 ............................ 1 .................. REPLACES 492364
WASHER FLAT 5/16 ..................................... 1 .................. REPLACES 492597
WASHER FLAT 5/16 ..................................... 1 .................. REPLACES 492623
NUT 5/16....................................................... 1 .................. REPLACES 492553
MUFFLER ..................................................... 1 .................. INCLUDEDWITH ENGINE
0202
EM923023
EM923343
2105164
835029
516291
0202
EM923343
2105164
517127
517328
506886
ELBOW, EXHAUST
1
SCREW, HHC 5/16-18 X 1 ............................ 4 .................. REPLACES 492364
WASHER LOCK 5/16" .................................. 4 .................. REPLACES 492623
NUT HEX 5/16" DIA-NC ................................ 4 .................. REPLACES 492553
WRAP 2" X 1/16" X 8' .................................. 11.5'............. REPLACES 510718
CLAMP
BOLT
1
4
EM923343
821001
WASHER LOCK 5/16" .................................. 4 .................. REPLACES 492623
GASKET, EXHAUST MANIFOLD
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 78 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
376
378
402
452
454
458
PART NO.
515801
515696
835007
515802
PART NAME
AIR INTAKE HOSE
HOSE AIR INLET
QTY.
1
1
REMARKS
AIR CLEANER .............................................. 1 .................. INCLUDEDWITH ENGINE
CLAMP
MOUNT, AIR CLEANER ............................... 1 .................. INCLUDED WITH ITEM 402
ELEMENT, AIR FILTER
3
M113621
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — RADIATOR ASSY.
RADIATOR ASSY.
PAGE 80 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — RADIATOR ASSY.
RADIATOR ASSY.
NO.
45
47
366
368
370
372
374
472
PART NO.
516422
516421
PART NAME
QTY.
2.62'
2.62'
1
REMARKS
TRIM EDGE1" X 1"
TRIM EDGE 3/4" X 3/4"
MOUNT RADIATOR OVERFLOW
BOLT HEX 6MM X 15 ................................... 2 .................. REPLACES 506599
WASHER SPRING 1/4" ................................ 2 .................. REPLACES 492622
BOLT 1/4" X 3/4"
NUT 1/4"-20 NYLON LOCK
RADIATOR MOUNTING KIT
515660
EM506599
2101402
492356
492581
835085
2
2
1
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —THROTTLE ASSY.
THROTTLE ASSY.
PAGE 82 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER —THROTTLE ASSY.
THROTTLE ASSY.
NO.
106
108
110
112
114
134
135
136
137
330
PART NO.
513323
513324
516487
508451
513325
510229
G201
PART NAME
QTY.
REMARKS
TRAVEL LEVER (FWD/REV)
CABLE, FORWARD/REVERSE
JOINT BALL
1
1
1
1
1
1
1
1
1
1
LOCK NUT 1/4" - 28 NF
ADVANCE CABLE SUPPORT
CABLE THROTTLE ASSEMBLY
KNOB HANDLE
LEVER HANDLE
NUT 1/4-20 HEX
DA1252
516116
EM968435
NUT
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — BRAKE CONTROL ASSY.
BRAKE CONTROL ASSY.
38
44
36
42
52
66
48
56
60
46
40
50
54
62
64
58
68
70
76
82
78
72
265
74
268
267
266
269
PAGE 84 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — BRAKE CONTROL ASSY.
BRAKE CONTROL ASSY.
NO.
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
82
PART NO.
506046
506158
PART NAME
LEVER, BRAKE
BOLT 5/16" NC x 3/4" G5
QTY.
1
4
REMARKS
492303
BOLT 5/16" NC x 1/1/4" G5 ............................. 1 ............... REPLACES 492365
WASHER, FLAT 5/16” ...................................... 2 ............... REPLACES 492597
NUT, NYLON 5/16”- 18 ..................................... 1 ............... REPLACES 492582
BRAKE LINK
BELL CRANK
BOLT 3/8” NC x 1/1/2" G5................................ 1 ............... REPLACES 492313
NUT, LOCK 3/8” ............................................... 1 ............... REPLACES 492583
BRACKET, BRAKE
BOLT 5/16" NC x 1" G5
PIN, CLEVIS
KEY, COTTER
ROD BRAKE UPPER
PIN, CLEVIS
KEY, COTTER ................................................. 1 ............... REPLACES 491687
NUT, HEX 5/8" ................................................. 1 ............... REPLACES 492570
WASHER, LOCK 5/8” ....................................... 1 ............... REPLACES 492627
BRAKE ROD
BOLT, HEX HEAD 3/8” NCX4”
WASHER, FLAT 3/8” ........................................ 2 ............... REPLACES 492598
NUT, LOCK 3/8” ............................................... 1 ............... REPLACES 492583
BUSHING, PLASTIC
SUPPORT, BRAKE SHOE
BRAKE PAD
RIVET
WASHER 3/16"
EM923023
2105164
506057
1
1
505999
EM963097
EM969013
506000
508674
506042
506044
508450
506043
2219
1
4
1
1
1
1
4702
EM923348
508449
1
1
503116
3019092
EM969013
506001
1
1
1
6
6
265# 513320
266# 505997
267# 508566
268# 508386
269
513193
BRAKE PAD ASSEMBLY ................................ 1 ............... INCLUDES ITEMS W/ #
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — BATTERY ASSY.
BATTERY ASSY.
150
144
146
158
160
154
152
148
156
NOTES:
REMOVE ITEMS 20
AND 29 ON PAGE 58
FOR BATTERY ACCESS
PAGE 86 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — BATTERY ASSY.
BATTERY ASSY.
NO.
144
146
148
150
152
154
156
158
160
PART NO.
514391
515119
515115
505624
506266
506153
514387
492359
2101402
PART NAME
QTY.
REMARKS
BATTERY 12V
1
1
1
CABLE (-) BATTERY
CABLE (+) BATTERY
BATTERY TERMINAL COVER......................... 1 ............... BLACK
BATTERY TERMINAL COVER......................... 1 ............... RED
WRAP
1
1
1
CLAMP, BATTERY
HEX HEAD SCREW 3/8"X2" NC G5
WASHER, LOCK 1/4” ...................................... 1 ............... REPLACES 492622
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SCRAPER ASSY.
SCRAPER ASSY.
PAGE 88 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
AR13D RIDE-ON ROLLER — SCRAPER ASSY.
SCRAPER ASSY.
NO.
106
108
110
112
114
116
118
120
122
PART NO.
513290
508433
PART NAME
QTY.
REMARKS
SCRAPER, SUPPORT
SCRAPER, RUBBER
PLATE BACKING
4
4
4
508434
EM963057
3019092
EM969013
EM963692
492584
BOLT 3/8” ..................................................... 12 ................ REPLACES 492313
WASHER, FLAT3/8” ...................................... 12 ................ REPLACES 492598
NUT, LOCK 3/8” ............................................ 12 ................ REPLACES 492583
BOLT, 1/2” UNC X 1-1/2” ................................. 8 ................ REPLACES 492394
NUT, LOCK 1/2”NC
WASHER 1/2” SPECIAL
8
8
621
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE
5. Parts must be in new and resalable
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
PAYMENT TERMS
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Terms of payment for parts are net 30 days.
FREIGHT POLICY
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LIMITATIONS OF SELLER’S LIABILITY
MINIMUM ORDER
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
RETURNED GOODS POLICY
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
PAGE 90 — AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
AR13D RIDE-ON TANDEM DRUM ROLLER — OPERATION & PARTS MANUAL — REV. #2 (09/15/11) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-537-1173
Technical Assistance
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Miele Refrigerator KWT 1601 Vi User Manual
National Instruments Welding System 321645c 01 User Manual
Nikon Camera Lens AF DC Nikkor 105mm f 2 D User Manual
Nokia Cell Phone 1108 User Manual
Oki Switch BISM2 User Manual
Omnimount TV Mount OM10057 User Manual
Optoma Technology Projector ET700XE User Manual
Oreck Carpet Cleaner STEAM200 User Manual
Oregon Trimmer HT255 User Manual
Panasonic Fax Machine KX PW30CL User Manual