OPERATION MANUAL
StreetPro Series
MODELS
SP706016
SP706020
SP706026
SP706030
SP706036
PROFESSIONAL PAVEMENT SAW
(DEUTZ BF3L2011 DIESEL ENGINE)
Revision #0 (02/13/09)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
P/N 38260
Download from Www.Somanuals.com. All Manuals Search And Download.
SILICOSIS/RESPIRATORY WARNINGS
WARNING WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SP7060 StreetPro Series
Professional Pavement Saw
Proposition 65 Warning ........................................... 2
Silicosis/RespiratoryWarnings ................................ 3
Table of Contents .................................................... 4
Training Checklist .................................................... 6
Daily Pre-Operation Checklist ................................. 7
Safety ................................................................... 8-9
Rules and Regulations ..................................... 10-14
Dimensions ........................................................... 15
Specifications ........................................................ 16
Engine Specifications ............................................ 17
Intended Use / Familiarization .............................. 18
Serial Tag Information ........................................... 19
Controls and Indicators ......................................... 20
Components.......................................................... 21
Basic Engine Information ...................................... 22
Choosing Proper Blade Size ............................ 23-24
Specific Tools / Saw Blades................................... 25
Installing the Blade........................................... 26-27
Blade Guards ................................................... 28-29
Water Delivery System .......................................... 30
Stay-level handlebars ........................................... 31
Battery................................................................... 31
Fueling the Saw .................................................... 32
Cold Weather Operation ....................................... 33
Pointer Adjustment ................................................ 33
Raise-Lower Controls ........................................... 34
Blade shaft Engage System.................................. 35
Wheel Drive System.............................................. 35
Operation ......................................................... 36-37
Loading and Transporting ..................................... 38
Maintenance .................................................... 39-55
Troubleshooting (Engine)................................. 56-57
Troubleshooting (Blade) ........................................ 58
Electrical Diagram to SN AF3700155 ................... 60
Electrical Diagram SN AF3700156 and Up.......... 61
Hydraulic Schematic to SN AF3700155............... 62
Hydraulic Schematic SN AF3700156 and Up ...... 63
Specifications are subject to change without
notice.
PAGE4 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
TRAINING CHECKLIST
TRAINING CHECKLIST
This checklist lists the minimum requirements for machine
maintenance and operation. Please feel free to detach it
and make copies. Use this checklist when training a new
operator or use as a review for more experienced operators.
Training Checklist
Description
Read Operator’s Manual completely.
No.
OK?
Date
1
Machine layout, location of components, checking of engine and
hydraulic oil levels.
2
3
4
Fuel system, refueling procedure.
Operation of spray and lights.
5
Operation of controls (machine not running).
Safety controls, safety stop switch operation.
Emergency stop procedures.
6
7
8
Startup of machine, pre-heat, engine choke.
Forward and Reverse Travel.
9
10
11
12
13
14
15
16
Starting a cut.
Pavement Cutting techniques.
Stopping a cut.
Re-start after stopping blade within work surface - explanation.
Shutdown of machine.
Lifting of machine (lift loops).
Machine transport and storage.
Operator _________________________________________ Trainee __________________________________________
COMMENTS:
PAGE6 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
DAILY PRE-OPERATION CHECKLIST
DAILY PRE-OPERATION CHECKLIST
Daily Pre-Operation Checklist
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1
2
3
4
5
6
Hardware and damage check.
Engine oil level.
Hydraulic oil level.
Condition of blade.
Safety Stop Switch operation.
Braking control operation.
COMMENTS:
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
FORYOUR SAFETY AND SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all
times when operating this equipment. Failure
to read and understand the safety messages
and operating instructions could result in injury
to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with Hazard Symbols which
appear throughout this manual, and will be referenced in
conjunction with Safety Message Alert Symbols.
WARNING — Lethal Exhaust Gas Hazards
Engine fuel exhaust gases contain
poisonous carbon monoxide. This gas is
colorless and odorless, and can cause
death if inhaled. NEVER operate this
equipment in a confined area or enclosed
structure that does not provide ample free
flow of air.
Thismanualhasbeendevelopedtoprovide
complete instructions for the safe and
efficient operation of this equipment. Refer
to the engine manufacturer’s instructions
for data relative to its safe operation.
Before using this equipment ensure that the operating
individual has read and understood all instructions in this
manual.
WARNING — Explosive Fuel Hazards
Fuel is extremely flammable and its
vapors can cause an explosion if ignited.
DO NOT start the engine near spilled fuel
or combustible fluids.
SAFETY MESSAGE ALERT SYMBOLS
The three Safety Messages shown below will inform you
about potential hazards that could injure you or others.The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER,WARNING,or CAUTION.
DO NOT fill the fuel tank while the engine
is running or hot. DO NOT overfill tank, since spilled
fuel could ignite if it comes into contact with hot engine
parts or sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas and away
from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operation. Never operate
the engine with heat shields or heat guards
removed.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if you
DO NOT follow these directions.
WARNING — Respiratory Hazards
CAUTION
ALWAYS wear approved respiratory
protection when required.
You CAN be INJURED if you DO NOT follow these
directions.
PAGE8 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CAUTION — Rotating Blade
Rotating blade can cut and crush. Keep
CAUTION — Overspeed Conditions
NEVER tamper with the factory setting of
the engine governor. Personal injury and
equipment damage can result if operating
in speed ranges above the maximum
allowable.
hands and feet clear.
CAUTION — Accidental Starting Hazards
WARNING — Skin Injection Hazards
Accidental starts can cause severe injury
or death. ALWAYS place the equipment
ON/OFF switch in the OFF position when
the equipment is not in use. Disconnect
negative battery cable from battery before
servicing
NEVER use your hand to find hydraulic
leaks. Use a piece of wood or cardboard.
Hydraulic fluid injected into the skin must
be treated by a knowledgable physician
immediately or severe injury or death can
occur.
CAUTION — Eye and Hearing Hazards
CAUTION — Guards and Covers in Place
ALWAYS wear approved eye and hearing
protection when required.
NEVER operate the saw without blade
guards and covers in place. Adhere to
safety guidelines and applicable local
regulations.
WARNING — Crush Hazard
CAUTION — Equipment Damage Hazards
ALWAYS ensure saw is SECURELY
placed on appropriate blocks or jackstands
when performing maintenance requiring
the saw to be elevated.
Other important messages are provided throughout this
manual to help prevent damage to your equipment, other
property or the surrounding environment.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult to read.
WARNING — ReadThis Manual
Failure to follow instructions in this manual may lead to
serious injury or even DEATH! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
ALWAYS check the equipment for loosened
threads or bolts before starting.
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing engine or pump.
GENERAL SAFETY
DO NOT operate or service this equipment
ALWAYS allow the engine to cool before adding fuel or
performing service and maintenance functions. Contact
with hot components can cause serious burns.
before reading this entire manual.
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment in any enclosed or narrow
area where free flow of the air is restricted. The engine of
this equipment requires an
adequate free flow of cooling
air. If the air flow is restricted it
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
will cause serious damage to
the equipment or engine and
may cause injury to people and
property. Remember the
engine gives off DEADLY
gases.
NEVER operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
NEVER operate this equipment under the
influence of drugs or alcohol.
ALWAYS use extreme caution when working with
flammable liquids.When refueling, stop the engine and
allow it to cool.
DO NOT smoke around or near the
equipment. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
NEVER disconnect any “emergency or safety devices.”
These devices are intended for operator safety.
Disconnection of these devices can cause severe injury,
bodily harm or even death! Disconnection of any of these
devices will void all warranties.
NEVER operate the equipment in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
NEVER use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
AVOID wearing jewelry or loose fitting clothing that may
snag on the controls or moving parts. This can cause
serious injury.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties. Any
modification which could lead to a change in the original
characteristics of the machine should be made only by
the manufacturer who shall confirm that the machine is
in conformity with appropriate safety regulations.
Make certain the operator knows how to and is capable
of turning the engine OFF in case of an emergency.
DO NOT top-off fuel tank.Topping-off is dangerous as it
causes fuel to spill.
PAGE10 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
NEVER use fuel as a cleaning agent.
Verify the engine start switch is set to the OFF position
before installing a blade.
ALWAYS store the equipment in a clean, dry location
out of the reach of children.
Use proper blades and follow the blade manufacturer’s
recommendations. Match the blade RPM (blade shaft
RPM) to the recommended blade surface feet per minute.
(SFPM).
NEVER run engine without air cleaner or air filter.Severe
engine damage may occur. Service air cleaner at
recommended service intervals to prevent engine
damage.
Ensure the 5/8" blade-mounting bolt is tightened to 125-
175 foot lbs. of torque.
NEVER leave the equipment unattended with the engine
running.Turn off engine when unattended.
NEVER leave the machine unattended while running.
CAUTION must always be observed while servicing this
equipment.Rotating parts can cause injury if contacted.
Ensure brakes are applied when leaving or when using
on a slope. This saw utilizes a brake system where the
brakes are automatically applied when the engine is
stopped.
ALWAYS keep the work area well-organized.
Keep the saw clean.It will perform better and last longer.
Start engine with the control handle in the NEUTRAL
position to prevent unexpected saw movement.
ALWAYS check to make sure that the cutting area is
clear before starting the engine. ALWAYS clear the
cutting area of any debris, tools, etc. that would
constitute a hazard while the saw is in operation.
Do not start engine on a sloping surface to prevent
unexpected loss of control.
DO NOT use on excessive slopes or on extremely
uneven surfaces.
Keep all inexperienced and unauthorized people clear of
the cutting area when operating the saw.
If the saw must be parked on a slope and engine turned
off, ensure the parking brake is engaged and holds the
saw safely in place.Turning the saw across the angle of
the slope will help prevent accidental downhill movement.
Block the saw as well when leaving.
No one other than the operator is to be in the working
area when the saw is in operation.
NEVER allow passengers or riders on the saw during
operation or transportation.
Make certain all protective guards are securely in place
BEFORE operating the saw.This saw is supplied with a
blade guard, blade flange guard and a belt guard.
NEVER place your feet or hands inside the guards while
starting or operating this equipment.
DO NOT go near rotating parts, (blades, belts, pulleys
or wheels), while engine is running.
Moving Parts – Shut down the engine
before performing service or maintenance
functions. Contact with moving parts can
cause serious injury.
NEVER touch the hot exhaust manifold,
muffler or cylinder.Allow these parts to cool
before servicing the saw.Contact with hot!
components can cause serious burns.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
Always store equipment properly when not being used.
Equipment should be stored in a clean, dry location out
of the reach of children.When storing the saw in freezing
weather, blow out the water lines to prevent damage to
components in the water delivery system.
DIAMOND BLADE SAFETY
Use appropriate steel-centered diamond blades
manufactured for particular use on your saw.See further
blade information in this manual.
DON'T POLLUTE!Waste Oils and other chemicals must
be disposed of in a manner consistent with local and
state environmental protection regulations.
WARNING — Inspect Diamond Blades
ALWAYS inspect diamond blades before
each use. The blade should exhibit no
cracks, dings, or flaws in the steel
centered core and/or rim. Center (arbor)
hole must be undamaged and true.
Always observe all applicable compulsory regulations
relevant to environmental protection, especially fuel
storage, the handling of hazardous substances, and the
wearing of protective clothing and equipment. Instruct
the user as necessary, or, as the user, request this
information and training.
Examine blade flanges for damage and excessive wear.
Ensure the cleanliness of the blade before blade is
installed. Blade should fit snugly on the shaft and against
the inside/outside blade flanges.
Ensure the blade is marked with an operating speed
greater than the spindle speed of the saw.
Only cut the material that is specified for the diamond
blade. Read the specifications of the diamond blade to
ensure the proper tool has been matched to the material
being cut. The saw has been engineered for WET
CUTTING.Ensure a WET CUTTING blade is being used
and that the water supply system to the blade is properly
functioning and being used.
ALWAYS keep blade guards in place. Exposure of the
diamond blade must not exceed 180 degrees.
Ensure that the diamond blade does not come into contact
with the ground or surface during transportation.DO NOT
drop the diamond blade on ground or surface.
The engine governor is set to permit maximum engine
speed in a no-load condition. Do not tamper with the
engine governor to increase the speed. Increasing the
engine speed could allow the maximum rated spindle
speed to be exceeded, creating an unsafe condition.
Ensure that the blade is mounted for proper operating
direction.
Adhere to the blade manufacturer’s recommendations
on handling, storage, and safe usage of blades.
PAGE12 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
TOWING SAFETY PRECAUTIONS (TRAILER USAGE)
CAUTION —Transporting Saw
SAW LIFTING AND LOADING SAFETY
CAUTION — Lifting Saw
Conform to Department ofTransportation (DOT) Safety
Towing Regulations before transporting saw on public
roads.
This saw is very heavy. Use proper heavy lifting
procedures and DO NOT attempt to lift by the guards.
DANGER — Do Not Stand Under Saw
To reduce the possibility of an accident while transporting the
saw on public roads, always make sure the trailer that supports
the saw and the towing vehicle are in good operating condition
and both units are mechanically sound.
NEVER stand under or allow anyone else to stand under
the saw while it is being lifted.
DO NOT use the handle bars and/or front pointer as lifting
points.
The following list of suggestions should be used when towing
your saw:
ALWAYS use ramps capable of supporting the weight
of the saw and the operator to load and unload the saw.
Check the tire air pressure on both towing vehicle and trailer.
Refer to the tire manufacturer’s recommended pressure.
Also check the tire tread wear on both vehicles.
NEVER tip the engine to extreme angles as it may cause
oil to gravitate into the cylinder head making the engine
start difficult.
Make sure the hitch and coupling of the towing vehicle are
rated equal to or greater than the trailer “gross vehicle weight
rating” (GVWR) of 6,000 lbs.
TRANSPORTING (VIATRUCK/TRAILER)
ALWAYS shutdown engine before transporting.
ALWAYS inspect the hitch and coupling for wear. NEVER
Tighten fuel tank cap securely and close fuel petcock to
prevent fuel from spilling.
tow a trailer with defective hitches, couplings, chains, etc.
ALWAYS make sure the trailer is equipped with Safety
Chains and ensure they are attached properly.
Drain fuel when transporting saw for long distances or
over bad roads.
ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and working.
Use appropriate lifting equipment to ensure the safe
movement of the saw.
DO NOT exceed the recommended highway speed when
towing.
When placing the saw on a truck-bed for transport,
always tie-down the saw.
Use chock-blocks at each wheel when parked to prevent
trailer from rolling.
Do not use the handlebars or front pointer as tie-down
points.
Use the trailer’s swivel jack to adjust the trailer height to a
level position while parked.
Never attempt to tow the saw untrailered behind a vehicle.
NEVER transport the saw to or from the job site with the
blade mounted.
Avoid sudden stops and starts.This can cause the trailer to
skid or jack-knife. Smooth, gradual starts and stops will
improve towing.
If the saw is being transported via a trailer, make sure
the trailer complies with all local and state safety
transportation laws.Refer to the following“Towing Safety
Precautions” section for basic towing techniques.
Avoid sharp turns.
Trailer should be adjusted to a level position at all times
when towing.
Raise and lock trailer wheel stand in the “UP” position when
transporting.
DOT requirements include the following:
Connect and test electric brake operation.
Secure portable power cables in cable tray with tie wraps.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES AND REGULATIONS
NEVER lubricate components or attempt service on a
BATTERY
running saw.
The battery contains acids that can cause injury to the
eyes and skin.To avoid eye irritation, ALWAYS wear safety
glasses or face shielding. Use well insulated gloves when
picking the battery up. Use the following guidelines when
handling the battery.
ALWAYS allow the saw a proper amount of time to cool
before servicing.
Prior to service, level the frame surface.
Anytime the saw is lifted onto its nose, or tilted fully
back, such as for maintenance access, the high end of
the saw MUST be blocked up to prevent the possibility
of crush injury.
DO NOT drop the battery. Any impact to the
battery may cause it to explode.
DO NOT expose the battery to open flames,
sparks, lit cigarettes etc.The battery contains
combustible gases and liquids. If these gases and liquids
come in contact with a flame or spark, an explosion can
occur.
Make sure that there is no buildup of concrete, grease,
oil or debris on the machine.
Repair damage to the saw immediately and always
replace broken parts.
ALWAYS keep the battery charged. If the battery is not
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
charged a buildup of combustible gas will occur.
ALWAYS recharge the battery in a well-ventilated area
to avoid risk of a dangerous concentration of combustible
gases.
DO NOT use plastic food containers to dispose of
hazardous waste.
ALWAYS keep battery cables in good working condition.
DO NOT pour waste oil or fuel directly onto the ground,
down a drain or into any water source.
Repair or replace all worn cables.
Disconnect battery cables before inspecting
electrical system and never “spark” battery
terminals to test for charge.
NEVER store saw with fuel in the tank for any extended
period of time. Always clean up spilled fuel immediately.
EMERGENCIES
If the battery liquid (dilute sulfuric acid)
comes in contact with clothing or skin,
rinse skin or clothing immediately with
plenty of water.
ALWAYS know the location of the nearest
fire extinguisher.
ALWAYS know the location of the nearest
first aid kit.
If the battery liquid (dilute sulfuric acid) comes in contact
with your eyes, rinse eyes immediately with plenty of
water, then contact the nearest doctor or hospital and
seek medical attention.
Know the phone numbers of the nearest ambulance,
doctor and fire department. Ensure that a phone or
radio is readily available at the jobsite. If this is not
possible, know the location of the nearest phone. This
information will be invaluable in the event of an
emergency.
MAINTENANCE SAFETY
Maintain this equipment in a safe operating condition at
all times.
ALWAYS shut down the engine and disconnect battery
before performing service or maintenance functions.
Contact with moving parts can cause serious injury.
Securely support any saw components that must be
raised.
PAGE14 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
See Figures 1 and 2 and Table 1 for saw dimensions.
E
C
D
A
B
Figure 1. Chassis and Dimensions — Side View
TABLE 1. CHASSIS AND DIMENSIONS
DESCRIPTION
REFERENCE
LETTER
DIMENSIONS
in. (mm)
A
B
C
D
E
F
G
H
I
Max Height (Front Pointer raised)
52-5/8 in. (1335 mm)
33-3/8 in. (847 mm)
77-1/4 in. (1962 mm)
57-1/8 in. (1450 mm)
114-1/4 in. (2901 mm)
36-1/8 in. (918 mm)
30-1/8 in. (765 mm)
50 in. (1270 mm)
Max Handle Bar Height
Max Length (Handle Bars Installed & Front Pointer fully raised)
Length (Handle Bars not Installed & Front Pointer fully raised)
Max Length (Handle Bars Installed & Front Pointer lowered)
Max Width
Frame Width
Frame Length
Front Wheel Width
28-1/8 in. (715 mm)
28-1/8 in. (715 mm)
33-5/8 in. (855 mm)
J
Rear Wheel Width
K
Blade Shaft Inner Flange to Inner Flange Width
Handlebars
Stay-Level Handlebar System
Vibration Control System
Console Mounting
Chassis
Cold-Formed Welded Box Construction
Optional
Night Light (M18004)
Crated Dimension (L x W x H): 60 x 43 x 64 in. (1525 x 1090 x 1625 mm)
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
H
G
K
F
I
J
Figure 2. Chassis and Dimensions — Bottom View
TABLE 2. BLADE AND SHAFT SPECIFICATIONS
Oil bath design, fully enclosed housing
Pressurized oil bath lubrication
2-3/8 in. (60mm)
Blade Shaft Assembly
Blade Shaft Bearings
Blade Shaft Diameter
Arbor Diameter
1 in. (25.4 mm)
Quick disconnect system, inner flanges mounted to shaft
4-1/2 in. and 6 in. (114mm and 152 mm)
10 belts, (2) 5G 3VX-530 multi-groove belts
20 in. (508 mm)
Blade Flanges
Blade Flange Sizes
Drive Belts
Max. Blade Raise Height
Blade Mounting
Left or Right
36 in. (914 mm)
Max. Blade Diameter
Max. Depth of Cut
Blade Guard Capacity
Blade Guard
15 in. (381 mm)
16-36 in. (406 mm-914 mm)
Slip-on, tapered mount
Electro-hydraulic pump
Blade Raise-Lower
Blade Shaft Clutch
Blade Shaft Clutch Control
Water Control
Standard
Belt drive tension automatically controlled by hydraulic tensioning system
Left and right side water valves
Dual water lines directly deliver water to blade
Water Distribution
PAGE16 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE SPECIFICATIONS
TABLE 3. ENGINE / MOTOR SPECIFICATIONS
Engine Manufacture
Model
Deutz
BF3L2011
3000
Max RPM
60.2
133.4 lb-ft.
Diesel
/
44.9
Horsepower
/
Max kW
/
181 Nm
Peak Torque
Fuel
8.25 gallons
Dual element radial seal with integral turbo pre-cleaner
8 quarts 7.5L
Oil to Air
/
31.2L
Fuel Capacity
Air Filter
/
Oil Capacity
Engine Coolant
TABLE 4. TRANSMISSION SYSTEM SPECIFICATIONS
Hydro-gear hydrostatic transmission pump
Hydro-gear hydrostatic wheel motors
0-275 FPM / 0-84 MPM, infinitely variable
Automatic actuating parking brake
12 in x 3 in. (305 mm x 76 mm)
Transmission Pump
Wheel Motors
Travel Speed
Brakes
Wheels Rear
Wheels Front
8 in x 3 in. (203 mm x 76 mm)
TABLE 5. WEIGHTS
1725 lbs. (782 Kg)
1825 lbs. (827.8 Kg)
Uncrated Weight
Crated Weight
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INTENDED USE / FAMILIARIZATION
INTENDED USE
FEATURES
Operate the SP7060 Multiquip Saw, tools and components
in accordance with the manufacturer’s instructions. Use of
any other tools for stated operation is considered contrary
to designated use. The risk of such use lies entirely with
the user.The manufacturer cannot be held liable for damages
as a result of misuse.
Stay-level handlebar system adjusts handlebar angle
automatically.
Engine stop switch conveniently located on operator’s
control panel.
Console mounted with vibration control system.
Chassis cold-formed welded box construction.
Pressurized oil bath lubrication (blade shaft bearings).
Oil bath design, fully enclosed housing.
ENGINE
The SP7060 saw is classified in the industry as a “high”
powered saw.This classification is particularly useful when
selecting the proper cutting tool (blade) for an application.
Quick disconnect blade flange system; inner flanges
mounted to shaft.
The SP7060 saw is powered by a liquid cooled, 3 cylnder,
turbocharged diesel engine rated at 60.2 HP (44.9 kW) at
3,000 RPM. Blade rotation is belt driven. Wheel Drive
system is driven by a hydrostatic transmission consisting
of a variable displacement pump and two fixed displacement
wheel motors.
Blade mounting left side or right side.
Saw position guide helps ensure straight cuts
Dual water lines directly deliver water to blade.
Slip-on, tapered mount blade guard for ease of removal
and installation.
Refer to the Engine Owner’s Manual for specific
instructions regarding engine operation and maintenance
practices.
Blade raise-lower by electro-hydraulic pump.
WATER SYSTEM
Belt drive tension automatically controlled by hydraulic
tensioning system.
All SP7060 saws provide a hardy water plumbing system
that evenly distributes water volume and optimum flow rate
to both sides of the blade to keep it cool when cutting.The
basic water system provides a valve that connects to a
standard garden hose.The water is delivered (via a hose)
to the saw blade.
Dual filter element air filter with integral turbo pre-cleaner.
Hydro-gear hydrostatic transmission pump.
Hydro-gear hydrostatic wheel motors.
Travel speed up to 84 MPM (meters per minute)/ 275
FPM.
All MULTIQUIP SP7060 saws are designed, engineered
and manufactured with strict adherence to American
National Standards Institute, Inc. (ANSI) guidelines B7.1
and B7.5.
Automatic actuating parking brake.
Optional night light.
PAGE18 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL TAG INFORMATION
1
2
MODEL
SERIAL NO.
Figure 3. Serial Tag/Locations
SERIALTAG
The serial tag contains the model number and serial number
of the saw. The information details all parts that were
included with the saw when it was shipped from the factory,
as well as the date of manufacture.
Record these numbers, in case you need to contact the
manufacturer for information or service in the future.
Record your ENGINE model, (Item 2) specification number
and serial number here:
The SERIAL TAG is bonded to the inside of the console
(Figure 3, Item 1).
Table 6. Serial Tag Information
SERIAL NUMBER
MODEL NUMBER
ENGINE NUMBER
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND INDICATORS
16 7
6
5
14
17
15
3
4
13
12
11
6
7
5
150
175
8
4
125
200
100
9
230
3
255
10
75
280
11
2
50
305
12
330
25
1
355
13
8
9
380
14
0
MM
0
15
INCH
2
1
10
18
Figure 4. Controls and Indicators
Figures 4 and 5 show the location of the controls, indicators
and general maintenance parts.The function of each control,
indicator or maintenance part is explained below.
7. Light Switch — When activated, turns on light. Lights
offer better visibility when working indoors.
8. Depth Indicator — Indicates relative depth of blade in
1. FNR Handle — Use to engage the saw in a forward or
backward direction. Push handle forward to move the
saw forward; pull handle back to move saw backward.
surface.
9. Depth Stop — Allows repeatable cutting depths.
10. LeftWater FlowValve — Meters water supply.
2. Raise/Lower Switch — Use to lift or lower the front of
11. Right Water Flow Valve — Opens and closes water
the saw (and blade if installed).
supply to water supply system.
3. Blade Shaft RPM — Indicates blade shaft speed in
12. Water Pump Switch (Optional) —Toggle to turn pump
revolutions per minute.
on or off.
13. Emergency Stop Button — Press the RED emergency
4. Throttle Control — Controls the speed of the engine.
Turn knob counter-clockwise to increase engine speed.
Turn knob clockwise to reduce engine speed.For quick
throttle response, depress red button and push or pull
knob.
stop button to shut the system down.
14. Socket Connector — Use to plug in optional light.
15. Blade Shaft Engage/Disengage Switch — Toggle
switch to engage or disengage the blade shaft drive.
5. System Status — Allows operator to monitor engine
16. Auxiliary Switch
and electrical functions.
17. Fuel Filler Cap — Remove this cap to add fuel.
6. Ignition Switch — With key inserted turn clockwise
18. Rear Access Panel — Remove to access items such as
to start engine.
the battery, hydraulic filter, etc.
PAGE20 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
15
1
14
16
2
17
13
10
21
18
3
4
12
19
8
22
20
11
6
23
7
5
9
Figure 5. Components
1. Front Pointer Assembly
2. BladeWrench
13. RightsideWater On/Off ControlValve
14. Light Assembly
3. Blade Shaft Pulley Guard
4. Blade Shaft Assembly
5. Blade Flange
15. Engine Assembly
16. Engine Fuel Filler Cap
17. Control and Indicator Panel
18. Stay-Level Handles (SLH)
19. Rear Access Panel
20. Flange Guard
6. Front Axle Assembly
7. LeftWheel Motor
8. Brake Cylinder
9. RightWheel Motor
10. Engine Guard
21. LeftsideWater MeteringValve
22. Belt Guard
11. Rear Pointer
23. Slurry Strip
12. Documentation Box
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC ENGINE INFORMATION
18
13
12
8
6
11
9
16
17
2
10
15
7
14
3
1
5
4
Figure 6. Basic Engine Components
9. V-beltTension Adjustment —This bolt provides means
BASIC ENGINE COMPONENTS
to adjust theV-belt tension at the alternator bracket.
The following refers to basic engine components and their
functions that an operator may need to reference. The
manufacturer’s engine manual provides further instructions
and details of operation and servicing. The engine shown
in Figure 6 is a Deutz BF3L2011 engine.
10. V-belt (Fan belt) — Driven by the engine crank during
operation, drives the fan as well as the aternator.
11. Oil Fill Cap — Remove to add engine oil.
12. Lifting Eye — The lifting eye is provided if the removal/
installation of the engine becomes necessary.
1. Fuel Filter — Removes dirt and water from the engine
13. Alternator — Located inside the fan assembly.Provides
current to the electrical system and charges the battery.
Driven by means of a crankshaft/V-belt pulley system.
fuel.
2. Governor Lever — This lever restricts engine speed
(high idle and low idle) through a speed control device
linked to the accelerator system.
14. Starter — Starts engine when ignition key is rotated to
the “START” position.
3. Oil Dip Stick — Remove to check amount and condition
15. Flywheel — Main power is taken off from the flywheel
of oil in crankcase.
end.
4. Oil Filter — Spin-on type, filters oil for contaminants.
16. Air Intake Port — Provides air from the air cleaner to the
5. Oil Drain Plug and Hose — Remove plug and attach
turbocharger unit.
drain hose to drain crankcase oil.
17. Turbocharger — Provides pressurized intake air to the
cylinder by means of a turbine energized by exhaust gas
that rotates the blower.
6. Oil Filler Port — Remove to add fresh crankcase oil.
7. CrankshaftV-Pulley — Check fanV-belt betweenV-Pulley
and fan to determine proper belt tension.
18. Air Cleaner Assembly — Provides clean filtered air to
8. Cooling Fan — Driven by theV-belt, the cooling fan cools
the engine by cooling engine oil that circulates through
the engine block and cylinder head.
the air intake port.
PAGE22 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING PROPER BLADE SIZE
CHOOSING PROPER BLADE SIZE
Ratio Speeds and Blade Guard Size
Proper blade selection is a product of:
The 7060 Series offer five blade guard sizes (16", 20", 26",
30", 36") that will accommodate most commonly used
diamond blades up to a 36" (914 mm). The series further
offers four distinct pulley ratio set-ups that provide specific
blade shaft RPM. Pairing a diamond blade diameter to a
proper ratio speed and blade guard size is imperative.
Additionally, matching up blade diameters with the
appropriate blade guard size is equally as important. See
Table 7.
■
■
■
■
■
■
■
Understanding the capability of your saw
Understanding the specifications of the engine
Understanding the blade shaft speed of your saw
Understanding diamond blade operating limitations
The depth of cut required
Cutting conditions
Table 7. Blade Guard Sizing Chart
Desired cutting performance requirements
Blade Guard
16"
14"
16"
20"
26"
24"
26"
30"
36"
Engine (RPM) and Surface Feet per Minute (SFPM)
Speeds
16"
24"
26"
Diamond Blade
Diameter (in.)
18"
20"
26"
30"
30"
36"
This saw uses a belt drive system to propel the diamond
blade. Specifically sized engine drive and blade shaft
pulleys, engine (RPM) and blade diameter determine the
ultimate peripheral speed (SFPM) of the diamond blade. It
is important to understand the SFPM speed — For safety
and performance, it is essential that the selected
diameter diamond blade be matched up to a proper
SFPM (see Table 8).
Five 7060 models are available (706016, 706020, 706026,
706030, 706036) and are designed with different pulley ratio
speeds to govern the blade shaft RPM output. The
combination of the different diameters of the pulleys along
with engine (RPM) determines this ratio that ultimately
provides a RPM speed at the blade shaft (Figure 7).
Figure 7. Blade Shaft Ratios
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING PROPER BLADE SIZE
Blade RPM vs. Surface Feet Per Minute (SFPM)
CAUTION
When choosing a blade for your cutting conditions, follow
the blade manufacturer's recommendations. Match the
blade speed (Blade Shaft RPM) to the recommended blade
Surface Feet Per Minute (SFPM). See Table 8.
Verify the engine start switch is OFF before removing
or installing a blade.
Tighten the 5/8" blade-mounting bolt to 125-175 ft. lbs.
of torque.
WARNING
Maximum allowable blade surface feet per minute per
ANSI Standard B.7.1 is 16,000 SFPM.
Table 8. Surface Feet per Minute (SFPM) Data ~ No Load
Blade
Shaft
Ratio: Engine
Engine Pulley
Blade
Flange
Dia.
Saw
Model
Depth of Eng RPM, Bladeshaft
14"
16"
18"
20"
24"
26"
30"
36"
Pulley Cut (in.) NO LOAD
Size
RPM
SFPM SFPM SFPM SFPM SFPM SFPM SFPM SFPM
RPM'S
Size
Circumference of Blade in Feet: 3.665
4.189 4.712 5.236 6.283 6.807 7.854 9.425
10733 12267 13801 15334 18401 19934 23001 27601
9490 10847 12203 13558 16270 17626 20338 24405
706016
706020
706026
706030
706036
1.02
1.16
1.61
1.61
1.70
4.10
4.10
3.30
3.30
3.30
4.20
4.75
5.30
5.30
5.60
5.75
7.50
3000
3000
3000
3000
2800
2929
2589
1868
1868
1650
4.50"
4.50"
4.50"
6.00"
6.00"
10.25
12.00
15.00
6846
6846
6047
7824
7824
6912
8802
8802
7775
9780 11737 12715 14671 17605
9780 11737 12715 14671 17605
8639 10367 11231 12959 15551
PAGE24 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC TOOLS / SAW BLADES
to an “under cutting” condition brought about by highly
abrasive material or improper under cutting core
protection.
SPECIFICTOOLSTO BE USED
This saw is to use tools (blades) as follows:
Steel core segmented or continuous diamond rim cutting
wheel
4. Directional Arrow — Check to ensure that the blade
is oriented properly on the spindle/arbor for sawing.
Reference the directional arrow on the blade and place
it so the direction of rotation “downcuts” with the turn
of the shaft.
Any other type of tool is not to be used.
SAW BLADES
5. Diamond Segment or Rim — Ensure there are no
cracks, dings, or missing portions of the diamond
segment/rim. DO NOT use a blade that is missing a
segment or a portion of the rim. Damaged and/or
missing segments/rims may cause damage to your
saw, and injury to the user or others in the operating
area.
WARNING — Inspect Diamond Blade
Failure to thoroughly inspect the diamond blade (Figure
8) for operational safety could result in damage to the
blade or the saw and may cause injury to the user or
others in the operating area. Discard damaged or worn
blades and replace with fresh blade.
6. Specifications — Ensure that the blade specifications,
size, and diameter properly match up to the sawing
operation. Wet blades must have water to act as a
coolant. Utilizing a diamond blade not matched properly
to the task may result in poor performance and/or blade
damage.
7. Arbor Hole — It is essential that the arbor hole diameter
properly matches the shaft arbor, and that it is free
from distortions. Correct blade flanges (collars) must
be used.The inside face of the flanges must be clean
and free of debris. An out of round arbor condition will
cause damage to the blade and the saw.
Figure 8. Diamond Blade
8. MAX RPM — This RPM reference is the maximum
safe operating speed for the blade selected. NEVER
exceed the max RPM on the diamond blade. Exceeding
the max RPM is dangerous and may cause poor
performance and may damage the blade. All blades
used must be designed for the maximum spindle RPM.
1. Drive Pin Hole — A commonly located hole on the
diamond blade core that prevents operational blade
slippage between the inner & outer blade flanges
(collars). Inspect the diameter of the hole to ensure
there is no distortion, and that a snug fit develops
between the hole and drive pin.
2. Stress Relief Holes (Gullets) — Check the steel core
for cracks that may have propagated from the slots
and/or gullets. Cracks indicate extreme fatigue failure,
and if sawing continues, catastrophic failure will occur.
3. Edge of the Steel Core — Check the diameter edge
for discoloration (blue oxidation) indicating an
overheating condition caused by insufficient cooling
water/air. Overheating of blades may lead to loss of
core tension and/or increase the possibility for blade
failure. Check to make sure the steel core’s width is
uniform about the rim of the blade and not succumbing
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE BLADE
INSTALLING THE BLADE
The blade can be mounted on either side of the saw to
accomodate different cutting jobs. With the proper sized
blade selected, reference the following procedure to install
the new blade.
Ensure the flange faces are kept clean and
smooth as well as the inside diameter of
the blade shaft.
1. Raise the saw so the blade will clear the ground when
Figure 10. Aligning Flange Pin Through Blade
WARNING —Tighten Blade Mounting Bolt
installed.
2. Remove the blade flange bolt.This bolt is LEFT-HAND
thread on the RIGHT side of the saw and RIGHT-HAND
thread on the LEFT side of the saw.
Failure to properly tighten the blade mounting bolt can
result in the bolts coming loose with the blade flange
potentially falling off the rotating blade shaft assembly.
The blade and other parts coming loose from the saw
during operation pose a high risk of serious injury or
even death!
3. Verify the blade flanges are clean and not damaged.
Pay particular attention to all holes and recesses.Clean
or “rod-out” as necessary (Figure 9).
6. With the blade still off the ground, tighten mounting bolt
as tight as can be achieved until blade spins. (Figure 11,
Item B shows tightening direction for blade mounted on
RIGHT side of saw.)
B
Figure 9. Inspect and Clean Flange
4. Taking note of the direction of rotation of the blade (Figure
11, Item A), insert the bushing and mounting bolt through
the outer flange and blade (Figure 10).
A
5. Align flange pin through the blade into the inner flange.
The blade mounting bolt on the right side of the
saw (as viewed from the operator’s position), has
a left-hand thread, while the bolt on the left side of
the saw has a right-hand thread.
A. Blade Direction of Rotation
B. Tightening Direction - Right Side
Figure 11. Blade Rotation Direction
PAGE26 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE BLADE
Stacking Blades for Wide Cuts
CAUTION — Improper Torque
Combining or stacking blades together to make wide cuts
requires and optional bushing extension kit.
An improperly torqued mounting bolt can cause the
inside diameter of the blade, blade shaft, and flange
bushing to quickly wear. This can result in poor cutting
characteristics or premature failure of these parts
,requiring replacement and machine “downtime.”
WARNING
NEVER attempt to stack blades beyond the capacity
of the kits described here. NEVER operate the saw
without blade guards in place.
2
■
■
Kit #18501 allows blade stacking from .375" to .75"
thickness.
Kit #18502 allows blade stacking from .75" to 1.125"
thickness.
1
1. Remove existing blade (See previous section).
1. 12 In. (30.48 cm)
2. Replace the standard flange bushing, outer flange, and
mounting bolt that came with the saw with the extended
bolt and bushing and the new outer flange supplied with
the kit. Remember that the mounting bolt for the right side
of the saw has a left-hand thread while the mounting bolt
for the left side of the saw has a right-hand thread.
2. 125-175 lbs (56.7-79.4 Kg)
Figure 12. Blade Wrench
125-175 lbs. (56.7 -79.4 Kg) of weight applied to
the end of the blade wrench will provide 125-
175 ft. lbs. (169.5 -237.3 Nm) of torque to the
blade mounting bolt. (Figure 12.)
3. Insert the bushing and mounting bolt through the outer
flange and stack of blades. Spacers are required between
blades when stacking multiple blades.The longer bushing
and bolt allow blades to be stacked together while
maintaining proper alignment of flange bushing into blade
shaft.
7. Lower the blade to the ground surface (Figure 13, Item A)
to prevent blade from spinning and tighten the mounting
bolt to 125-175 ft. lbs. (169.5-237.3Nm) of torque (Figure13,
Item B).
4. Align flange pin through the stack of blades into the inner
flange.
5. Tighten the 5/8" Mounting Bolt to 125-175 ft. lbs. of torque.
WARNING
The operator must match the diamond blade diameter
to the proper blade guard size. See Table 7.
B
A
Figure 13.Torque Flange Bolt
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE GUARDS
3. With the opposite hand, grasp the rear handle and rock
back and forth with an upward pressure to release the
blade guard tapered mounting clip. Lift straight up, then
pull back once the tapered lock is released. Install blade
guard in reverse order.
BLADE GUARD
The blade guard can be mounted on either side of the saw
to accomodate different cutting jobs.
Removing a Blade Guard:
The saw utilizes a tapered blade guard mounting
clip that, during operation, settles in the taper by
the weight of the guard locking itself into place,
providing a rigid, rattle-free fit.
1. Remove the water delivery hose from the blade guard
(Figure 14).
Figure 14. Blade GuardWater Delivery Connector
Figure 15. Removing The Blade Guard
2. Standing toward the back of the blade guard, grasp
the top handle firmly with your outboard hand (this will
be the right hand if the guard is mounted on the right
as viewed from the operator’s position), and prepare to
support the weight of the blade guard (Figure 15).
WARNING
NEVER operate the saw with the front half of the Blade
Guard removed.
PAGE28 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE GUARDS
Installing a Blade Guard
Blade Guards with StandardWater Systems:
1. Slide the blade guard straight downward to engage the
tapered mounting clip (Figure 16).
Figure 18.WaterTube Detail (Inner side)
Figure 16.Tapered Mounting Clip
Blade Guards withWaterjetWater Systems:
2. Connect the water delivery hose to the blade guard
1. Slide the blade guard straight downward to engage the
tapered mounting clip (Figure 16).
(Figure 14).
3. Ensure that the hose ends maintain a 45o angle and
2. Ensure that the water delivery tubes are pointed toward the
maintain a light contact with the surface of the blade.
water distribution grooves in the blade flanges (Figure 20).
4. Ensure the front hinged section of the blade guard is fully
3. Ensure the front hinged section of the blade guard is fully
closed before use.
closed before use.
INSTALLINGTHE FLANGE GUARD
The flange guard protects the blade flange when not in use.
1. Slide the flange guard onto the guard mounting tab on the
frame (Figure 19).
2. Verify that the blade flange not in use is secured to the
blade shaft by tightening the mounting bolt.
Figure 17.Water Hose Detail
Figure 19. Flange Guard Installed
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER DELIVERY SYSTEMS
WATER DELIVERY SYSTEM
CAUTION
When storing the saw where temperatures may drop
below freezing, blow out the water lines to prevent
damage to the water delivery system.
1. Connect the water supply hose to the water inlet
(garden hose) fitting on the left side of the saw (Figure
5, Item 21).
2. Verify that the water hose on the saw is connected to
the blade guard, (Figure 14), and that the water hoses
or tubes are pointed into both blade flanges.
3. Ensure that the hose ends maintain a 45o angle and
maintain a light contact with the surface of the blade.
Figure 20. Large Bladeguard Water Tube
The lever on the left side of the control panel
regulates water flow volume. The lever on
the right side of the control panel turns the
water ON and OFF.
PAGE30 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
STAY-LEVEL HANDLEBARS/BATTERY
STAY-LEVEL HANDLEBARS (SLH)
WARNING — Shock hazards
This saw incorporates a unique handlebar design that allows
the handlebars to maintain a level height position regardless
of the angle of the saw. Along with this, the height of the
handlebars can be adjusted for individual operator providing
for more comfortable operation.
Disconnect battery cables before inspecting
electrical system and never “spark” battery
terminals to test for charge.
To adjust the handlebar height:
CAUTION — Battery safety
1. Loosen the SLH linkage adjustment plate bolts (Figure 21).
2. Set the handlebars to the desired height.
3. Tighten the SLH linkage adjustment plate bolts.
Use all safety precautions specified by the battery
manufacturer when working with the battery.
This saw was shipped with a wet charged battery (Figure 22).
This battery may need to be charged for a brief period of time
as per the manufacturer instructions.
Figure 22. Battery and Battery Box
Figure 21. Stay-Level Handlebars
BATTERY SETUP
To install the battery on the saw, make sure that the battery is
properly clamped into the battery box. Connect the positive
cables to the positive terminals on the battery first, then connect
the negative cables to the negative terminals.
WARNING — Battery hazards
Always recharge the battery in a well-
ventilated area to avoid risk of a dangerous
concentration of combustible gases.
Battery electrolyte contains corrosive,
toxic chemical. (dilute sulfuric acid). Avoid
contact with eyes and skin.
The 7060 uses two positive battery cables and
two negative battery cables. One set is for engine
start, and the other is for the raise/lower pump
assembly.Make sure that both sets of cables are
connected to the battery.Also, LIMIT the cycling
of the raise/lower system on battery power only.
Frequentcyclingwilldiminishthelifeofthebattery.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
FUELING THE SAW
FUELINGTHE SAW
Priming the Fuel System
This saw features an 8-gallon, clear, molded plastic fuel
tank for ease of checking the fuel level. It has a central
drain and a shutoff valve. The fuel tank cap is located at
the front of the control panel console, and a fuel gauge
tube is featured on the front of the console.
Saws UPTO S/N ZC3700225 utilize a fuel primer bulb when
fueling the saw for the first time or refilling after running out
of fuel. Locate the fuel primer bulb inside the console
beneath the fuel tank (Figure 24, Item A) and squeeze the
fuel priming bulb until it fills with fuel, (it will become firm
when properly primed), priming the fuel transfer pump.
CAUTION — Fuel Safety
Saws AFTER S/N ZC3700225 utilize a fuel primer button
built into the engine transfer pump (Figure 24, Item B).
Handle fuel safely.
Motor fuels are highly flammable and can be
dangerous if mishandled.
WARNING — Fuel
DO NOT crank the engine without fuel in the line
between the tank and the primary fuel pump to prevent
damage to the primary fuel transfer pump.
DO NOT smoke while refueling.
DO NOT attempt to refuel the saw if the engine is hot or
running.
Avoid spilling fuel on the control panel or engine.Clean up
fuel spills to avoid falls from slipping.
A
DO NOT overtighten the fuel tank cap.
WARNING — Diesel Fuel only
Use DIESEL FUEL ONLY.
NEVER use gasoline or fuels not specifically for use in
the Deutz Diesel engine.
B
1. Determine if the engine fuel is low.( Figure 23)
2. If fuel level is low, remove the fuel filler cap and fill with
diesel fuel (Cetane fuel number 45 or greater).
Figure 24. Fuel Primer Bulb (A) or Button (B)
Storage With Fuel In System
CAUTION — Fuel
DO NOT store with fuel in the tank for an extended
period of time. Completely drain fuel system (tank, lines,
etc.) if the unit is to be put into long term storage. For
shorter or intermediate periods of time, the tank should
be filled to avoid condensation that could cause
contamination of the fuel.
Figure 23. Fuel Gauge
PAGE32 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
COLD WEATHER OPERATION/POINTER ADJUSTMENT
to lock the pointer in position. Repeat this process for the
rear pointer.
COLDWEATHER OPERATION
Block Heaters
4. To raise the front pointer assembly (Item 1), first pull back
and up on the pointer cable. Secure the pointer assembly
in the desired raised position by locking the cable between
the jaws of the cam cleat.
CAUTION — Block Heaters
DO NOT leave optional block heaters plugged in for
extended periods when temperatures may rise above
20oF, (-6.67o Celsius). The oil could “cook” inside the
crankcase and damage the engine.
If the water system is not drained when the saw is not
in use and temperatures fall below 32o F (0o C), damage
may occur to optional water pumps.
In extreme cold weather, optional block heaters may be used.Block
heaters are installed directly onto the crankcase and are operated
by plugging into a 110VAC electrical outlet. Be sure to use
appropriate gauge wire when using extension cords and abide by
all safety rules when using electical power, power cords, and
extension cords. Do not use block heaters when the when
temperatures are above 20o F (-6.67o Celsius).
Draining the Water System
When low temperatures fall below 32o F (0o C):
1. If the saw is equipped with an optional water pump, open
the drain petcock on the pump and allow the pump to
drain.Turn the water pump switch on for a few seconds to
purge any water remaining inside the pump body.
Figure 25. Pointer Assembly
2. Tilt the saw UP and BACK, to allow water to drain.
3. Tilt the saw FORWARD, to allow water to drain again.
4. If an air compressor is available, blow out the system by
applying compressed air to the water inlet.
2
POINTER ADJUSTMENT
1. Lower the front pointer assembly (Figure 25).
2. Using 10-12 ft. (3-3.7 meters) of stringline, divide the length
of the string in half and slide the string into one of the
slots or gullets on the backside of the blade (as viewed
standing in front of the pointer) SeeFigure 26, Item 2. Hold
both ends of the string in one hand and pull the string taut
(Item 3). Move your hand from side to side until both strings
are touching both sides of the blade.
1
5
4
Top View
3. Adjust the pointer rod (Item 5) by loosening the lock knob
(Item 4). Move the pointer directly over the middle of the
two strings in your hand and tighten the pointer setscrew
3
Figure 26. Adjusting the Pointer Assembly
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
RAISE-LOWER CONTROLS
RAISE - LOWER CONTROLS
Depth Control System
The SP7060 saw uses a 12-volt hydraulic pump and cylinder
to raise and lower the saw. The raise-lower function is
controlled by the operator through a 3-position toggle switch
on the raise-lower control handle located on the operator’s
control panel.
The SP7060 saw uses an electronically controlled depth
stop to position and lock the blade at the desired cut depth.
To control the depth of cut with the saw running and blade
mounted:
1. Raise the saw above the desired cutting depth.
2. Turn the depth control knob counterclockwise until the
saw cannot be lowered by pushing the raise/lower switch
forward (Figure 29).
1
Raises
Lowers
Figure 27. Raise-Lower Control Toggle Switch
2
1. To lower the blade, push the toggle switch located on
the end of the control handle FORWARD (Figure 27).
1
2. To raise the blade, pull the toggle switch located on
the end of the control handle BACKWARD.
Setting the Depth Indicator
6
1. Lower the blade until it just touches the cutting surface.
4
5
2. Set the depth indicator dial to zero.The depth indicator
now accurately indicates how deep the blade is cutting
(Figure 28).
1. Depth Control Knob
3
2. Raise/Lower Toggle Switch
3. Adjuster Bracket
4. Adjuster Cable/Spring assy.
5. Adjuster Nut
6. Depth Control Housing
5
4
6
125
5
50
150
100
7
0
3
175
5
75
200
8
0
2
50
230
30
9
255
5
1
25
10
280
Figure 29. Setting Depth Gauge and Depth Stop
0
11
0
0
305
MM
INCH
CH
330
12
0
355
5
380
13
0
14
15
3. Hold the raise/lower toggle switch in the lowering
position by pushing it forward and rotate the depth
control knob clockwise until the desired cutting depth
is achieved. The saw will repeat to the same depth
until readjusted.
Figure 28. Depth Indicator
PAGE34 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
BLADE SHAFT ENGAGE SYSTEM / WHEEL DRIVE SYSTEM
To Re-adjust for full cutting depth:
WHEEL DRIVE SYSTEM
1. Hold the raise/lower switch in the lowering position and
rotate the depth control knob clockwise until the saw is
fully lowered.
The 7060 Series features a cable-controlled hydraulic
powered gear motor system with infinite Forward-Neutral-
Reverse (F-N-R) speed adjustment. This is controlled by
the operator through the speed control handle located on
the control panel. The saw is designed with a locked axle
drive and can travel forward at transportation speeds up to
275 feet per minute.
2. Rotate depth control knob clockwise an additional 1 turn.
To disable the depth stop when it is not needed:
1. While holding the raise-lower toggle switch FORWARD,
rotate depth control knob CLOCKWISE until saw is at full
depth position.
A bi-directional variable displacement transmission pump
powers two hydraulic wheel motors that are directly coupled
to the wheels. This design provides vehicle propulsion in
both forward and reverse depending on the position and
direction of movement of the F-N-R control handle. The
wheel drive system also provides dynamic braking action.
2. Rotate depth control knob an additional 1-2 turns.
BLADE SHAFT ROTATION — DISENGAGEMENT
SYSTEM
The engine MUST be at IDLE when engaging or disengaging
blade shaft drive (Figure 30, item 1).
Hydraulic system pressure must be sufficient to
enable the blade shaft engage/disengage feature.
Increasing engine RPM slightly may help facilitate
the system pressure necessary to engage the
blade shaft drive.
To STOP blade shaft rotation:
Push rocker switch labeled BLADE SHAFT DISENGAGE
(Figure 30, item 2).The engine (via the hydraulic lift cylinder)
will tilt forward, disengaging the belt drive.
Figure 31. F-N-R Control
To START blade shaft rotation:
Refer to Figure 31.
Push rocker switch labeled BLADE SHAFT ENGAGE
(Figure 30, item 2).The engine (via the hydraulic lift cylinder)
will tilt backward, engaging the belt drive.
■
■
■
■
To increase the forward speed, slowly move the control
handle FORWARD.
To decrease the forward speed, pull the control handle
BACKWARD.
2
1
When the control handle is in the Neutral position the
saw will have neither a forward nor reverse motion.
As the control handle is passed backward through the
neutral position the saw will start to move in REVERSE.
Reverse speed is also controlled by the position of the
control handle.
Figure 30. Blade shaft Engage/Disengage
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING AND STOPPINGTHE ENGINE
WARNING
DO NOT leave the saw unattended while the engine is
running.NEVER start, park, or leave the saw unattended
on a slope.
CAUTION
Allow the engine to warm up before increasing engine
speed.
1. Engine oil pressure warning light
2. Engine high temp warning light
3. Glow plug warning light
4. Not used
5. Air filter warning light
6. Battery warning light
DO NOT stop the engine abruptly when hot.Reduce the
throttle to idle and allow the engine to run one or two
minutes before turning the ignition switch off.This allows
the engine to cool down preventing damage to the turbo
charger.
Figure 33. Ignition Switch and System Status
Starting the Engine
8. Allow the engine to warm up for several minutes.
1. Move the speed control handle to the NEUTRAL
position.
9. Set the throttle to the recommended engine RPM to match
the recommended blade speed of the attached blade.
2. Set the throttle to IDLE.
10. Lower the blade to the cut depth.
3. Make sure the emergency stop button is in the OUT
position.
11. Move the control handle FORWARD to advance the cut.
4. Ensure that water lines are attached and water is
flowing to the saw blade.
In case of an EMERGENCY, push the RED
EMERGENCY-STOP BUTTON to stop all
functions (Figure 34). Engine will not crank
when emergency stop button is depressed.
5. Turn the ignition switch to the ON position (Figure 32).
Figure 32. ON/OFF Switch
6. Wait for the glow plug indicator light to go out. See
Figure 33.
Figure 34. Emergency Stop Button
7. Turn ignition switch to the START position; RELEASE
switch after engine starts.
PAGE36 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Stopping the Engine
OPERATING SYNOPSIS
1. When finished with the cut, move the control handle to
the NEUTRAL position.
BEFORE STARTING — Check all fluid levels.Secure blade
firmly to blade shaft. Make sure all protective guards
are in place and properly mounted. Wear eye, ear
protection and protective clothing.
2. Raise the saw blade out of the cut.
3. Reduce the throttle to idle.
WATER SUPPLY— Connect water supply to water inlet.
Move water ON/OFF CONTROL to ON position. Adjust
WATER FLOW CONTROL lever to desired position.
Drain watering system in cold weather to prevent
damage due to freezing.
4. Allow the engine to run one or two minutes to let the
engine cool down.
5. To stop the engine, turn the Ignition Switch to the OFF
position.
Restarting After Running Out of Fuel
BLADES — Always follow blade manufacturer’s
recommendations for blade selection, speed and
application. NEVER exceed blade manufacturer’s
maximum rated RPM. See previous steps for
detailed blade mounting instructions.
The 2011 series Deutz engines do not require bleeding of
the fuel system if the engine runs out of fuel.
To restart the engine:
1. Refill the fuel tank with fresh, clean diesel fuel.
STARTING ENGINE — Set CONTROL HANDLE to
NEUTRAL position.SetTHROTTLE to IDLE.Turn start
switch to ON position.Wait for glow plug indicator light
to go out. Momentarily turn switch to start position;
release switch as soon as engine starts. Allow engine
to warm up for several minutes before increasing
engine speed. Use approved diesel fuel only.
2. Units up to S/N ZC3700225 only: Re-prime the fuel
system by squeezing the fuel prime bulb (located inside
the console, directly under the fuel tank), until the fuel
primer bulb becomes firm.
3. Crank the engine normally until it starts.
STOPPING ENGINE — Do not stop engine abruptly when
hot! Reduce THROTTLE to IDLE and allow engine to
run 1 to 2 minutes before turning ignition switch off.
Damage to engine may occur if not allowed to cool
adequately.
FWD-NEUTRAL-REV CONTROL — The panel mounted
handle controls FORWARD, NEUTRAL AND
REVERSE operation. Neutral position stops or holds
saw in a stationary position. Incremental movement
in the FORWARD or REVERSE direction will
increase speed proportionate to amount of
movement.
RAISE-LOWER FUNCTION — RAISE-LOWER function is
controlled by the switch mounted at the right side of
the CONTROL HANDLE. Push toggle switch lever
forward to lower saw.Pull toggle switch lever backward
to raise saw.
BRAKES — This saw is equipped with parking brakes.
Brakes are applied automatically when engine is off
and disengaged when engine is running.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING AND TRANSPORTING
LOADING, UNLOADING ANDTRANSPORTINGTHE
SAW
Lifting Point
The convenient single point for lifting the saw with a hoist
is located above the engine (Figure 36).
Loading and Unloading
WARNING
When LOADING, UNLOADING or when on a STEEP
SLOPE, the engine MUST BE at 1800 RPM or above
to prevent loss of control.
Tie-Down Points
Figure 36. Lifting Point
The saw is provided with holes at each corner of the lower
frame for easy tie-down during transportation. See Figure 35.
WARNING
AVOID INJURY!
Stay clear of the saw while it is being hoisted.
CAUTION
To avoid possible damage to the saw, use approved
rigging (minimum 3000 lb. test) when hoisting the saw.
NEVER tie the back end of the saw down by strapping
across the handlebars. Damage to the SLH (Stay Level
Handles) system will occur.
Night Light
CAUTION
The night light (Figure 37) can be used on either side of the
saw and can be extended and rotated for best illumination of
the cutting area. Aim the light then lock it in position by tightening
the lock knobs. The light can be removed for storage by
loosening the lock knobs, disconnecting the light cord and
sliding the light bar out of the saw.
The use of tie-downs to secure the saw during
transportation is highly recommended.ALWAYS secure
the saw during transportation to prevent unwanted
movement or shifting that could result in equipment
damage or injury to personnel.
To turn lights ON, push the rocker-style switch located on the
instrument panel forward.To turn lights OFF, push rocker switch
backward.
Figure 35. Tie-Down Points
Figure 37. Night Light
PAGE38 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MAINTENANCE
WARNING
Maintenance Schedule
Daily (8-10 Hours)
1. Check fluid levels in engine and reservoir; fill as
necessary.
Certain maintenance operations or machine adjustments
require specialized knowledge and skill. Attempting to
perform maintenance operations or adjustments without
the proper knowledge, skills or training could result in
equipment damage or injury to personnel. If in doubt,
consult your dealer.
2. Visually inspect for wear and damage.
3. Visually inspect for engine leaks.
4. Check or replace the engine air filters as necessary.
5. Check operation of emergency stop button.
Monthly (125-150 Hours)
When performing maintenance operations on the
saw or engine, follow all safety messages and rules
for safe operation stated here and at the beginning
of this manual.
1. Change hydraulic oil and filter (first 125 hours, then
every 250 hours).
See the engine manufacturer’s manual supplied with your machine
for appropriate maintenance schedule and troubleshooting guide
for problems.
2. Change engine oil and filter.
Yearly (500 Hours)
1. Replace fuel filter cartridge and v-belt.
2. Check fuel lines for leakage.
WARNING — Accidental Starting Hazards
Accidental starts can cause severe injury or death!
3. Check battery cables and connectors.
4. Check engine monitoring and warning system.
AIR CLEANERS (DAILY)
ALWAYS place the ON/OFF switch in the
OFF position.
Engine and muffler surfaces can get HOT!
The saw utilizes both a primary air filter and a safety air
filter (Figure 39). The air filter restriction light (Figure 38,
Item A) on the engine status indicator (Figure 38, Item B)
will illuminate when the filter is plugged.
Allow to cool before servicing.
ALWAYS ensure saw is SECURELY
placed on appropriate blocks or jackstands
when performing maintenance requiring the
saw to be elevated.
A
CAUTION — Clean up spills
B
Avoid slips and falls!
Figure 38. Air Filter Restriction Light
Clean up all engine oil, hydraulic oil, and
diesel fuel spills immediately.
Empty the dust discharge valve daily and clean the
discharge slot from time to time (Figure 39).
While the air filters should be checked daily and replaced
when necessary, there is no need to “over-service” the air
filters.That is, they require no cleaning and do not require
the use of oil. If the primary filter becomes clogged, simply
replace it.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Never blow dirt out with compressed air or try to clean with
fluids. Damage can occur to the filter, and if re-installed,
can result in damage to the engine.
ENGINE
This saw features a 60 HP DEUTZTier IITurbocharged diesel
engine, BF3L2011. Complete engine service details and
recommendations can be found in the engine manufacturer’s
manual included with the saw. See Figure 40.
CAUTION — Air Filters
Safety air filters are NOT intended to be used for primary
air filtration.When the primary air filter becomes clogged,
replace it immediately. DO NOT run the saw using the
safety filter only.
2
4
15
Replace the safety filter element every fourth primary filter
element. SeeTable 9.
16
18
1
Table 9. Air and Oil Filter Chart
FILTER
PART NUMBER
Primary Air Filter
Safety Air Filter
Engine Oil Filter
Hydraulic System Filter
Fuel Filter
P772579
P775300
306012 (Deutz #1174416-SP)
306006
5
304010 (Donaldson #1174696)
14
17
7
1
2
19
3
3
1
13
4
9
6
10
8
5
1. Air Cleaner Case
12
11
2. Primary Filter Element
3. Safety Filter Element
4. Latch
1. V-belt
11. Engine Oil Filter
12. Drain Plug (engine oil)
13. Filler Port (engine oil)
14. Crank Shaft V-pulley
15. Cooling Fan
16. Adjustment bolt (V-belt
tension)
17. Belt Guard
2. Rocker Arm Cover
3. Fuel Injection Pump
4. Alternator
5. Starter motor
6. Flywheel
7. Air Filter/Cooling System
8. Fuel Filter
9. Throttle Lever
10. Dipstick (engine oil)
5. Dust DischargeValve
Figure 39. Air Cleaner Components
CAUTION — Air Cleaner Components
Operating the engine with loose or damaged air cleaner
components could allow unfiltered air into the engine
causing premature wear and failure.
18. Fan Cover
19. Oil Cooler
Figure 40. Engine Service Areas
PAGE40 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checking Engine Oil
Table 10. Recommended Viscosity Grades
SAE 0W-30, 0W-40
1. Check engine oil level daily before starting the engine.
2. When checking or adding oil, place the machine so
the engine is level.
SAE 5W-30, 5W-40
3. Pull the engine oil dipstick from its holder (Figure 40,
Item 10, Figure 40).
SAE 10W-30, 10W-40
SAE 15W-40
4. Determine if engine oil is low. Oil should be between
the upper and lower limit (add oil) lines.
SAE 20W-50
5. If oil is below the “Add Engine Oil” line, add oil up to
the upper limit on the dipstick. Allow enough time for
any oil to make its way to the oil pan before rechecking.
F -20
C -30
0
32 40
60
80
100
40
20
-10
10
-20
0
20
30
TEMPERATURE RANGE EXPECTED BEFORE NEXT OIL CHANGE
Oil Filter (125 Hours)
CAUTION — Do Not Overfill Oil Pan
1. Replace the engine oil filter (Figure 41) every oil change
or 125 hours. Refer to your engine manual for specific
details to perform this operation.
DO NOT overfill the oil pan with engine oil.Always keep
the engine oil level at the upper limit lines on the dipstick
due to the tilting of the engine during operation.
Changing Engine Oil And Filter
1. Change the engine oil after the first 5 hours of use,
then change every 6 months or 125 hours.
2
2. Remove the oil filler cap (Figure 40, Item 13), and fill
engine crankcase with recommended type oil as listed in
Table 2. Fill to the upper limit of dipstick.
3. Crankcase capacity with filter replacement is 8 quarts,
(7.57 liters).Refer toTable 10 for recommended viscosity
grade for temperature range.
1
1. Engine Oil Filter
2. Filter Seal
Figure 41. Oil Filter
2. Be sure to coat the seal of the new oil filter with clean
engine oil.
3. Spin on new filter until seal make contact with surface,
then tighten additional 2/3 to 3/4 turn.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Fuel Filter (500 Hours)
LUBRICATION
Replace the engine fuel filter (Figure 42) every 500 hours.
Refer to your engine manual for specific details to perform
this operation.
This saw has many service-saving features, including fully
enclosed oil bath lubricated blade shaft bearings that require
no daily lubrication.
This saw has 4 grease fittings on the front axle assembly.
See Figure 43.
Grease these fittings every 125 hours of operation with a
premium grade waterproof E.P.(extreme pressure) grease.
WARNING — Crush Injury
Prevent Crush Injury!
Ensure the saw is securely placed on
blocks before servicing lubrication points.
1
Figure 42. Fuel Filter Removal
Oil And Fuel Lines
Check the oil and fuel lines and connections regularly for
leaks or damage. Repair or replace as necessary.
Engine Tune-Up
See your engine manual for specific information on tuning
up your engine.
See the engine manual supplied with your
machine for appropriate engine maintenance
schedule and troubleshooting guide for
problems.
At the front of the book, there is a “Daily Pre-Operation
Checklist.” Make copies of this checklist and use it on a
daily basis.
Disconnect negative (ground) battery cable and secure away
before attempting any service or maintenance on the saw.
1. Front Axle Pivot Bearing
2. Hydraulic Lift Cylinder End
Figure 43. Grease Fittings
PAGE42 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
COOLING SYSTEM
BATTERY/CHARGING SYSTEM
The Deutz 2011 Series engine uses a robust, heavy duty
oil cooler system to cool the engine. The cooling system
will benefit from periodic inspection and cleaning.
WARNING — Battery hazards
Always recharge the battery in a well-
ventilated area to avoid risk of a dangerous
concentration of combustible gases.
1. Disconnect the air intake hose at the lifting bale (Figure
44, Item A).
Battery electrolyte contains corrosive,
toxic chemical. (dilute sulfuric acid). Avoid
contact with eyes and skin.
2. Remove 3 bolts that mount the air filter bracket to the
engine (Item B), and cover the oil cooler (Item C).
3. Remove the air box cover (Item D).
Shock or Fire due to electric short-circuit.
Disconnect battery cables before inspecting
electrical system and never "spark" battery
terminals to test for charge.
D
This saw uses a Group 75, 12Volt, 850 CCA (cold cranking
amp) AGM Technology battery. See Figure 45.
1. Check and clean battery terminals for corrosion.
B
2. Never attempt to charge a battery that is frozen. The
battery can explode unless first allowed to thaw.
A
3. Disconnect the negative terminal ( - ) of the battery
during storage. If unit will be stored where ambient
temperature will drop to -15o C or less, remove and
store battery in a warm, dry place.
C
B
Figure 44. Air Cleaner Removal
4. Use a nylon bristle brush to gently brush the underside
of the oil cover to break loose any accumulated dirt
and debris.
5. Using compressed air, carefully blow from the top of
the oil cooler to remove lodged dirt and debris. Blow
out any dirt out of the air box.
6. Use compressed air to next blow accumulated dirt and
debris from the fan air intake, fan, and fan tunnel.
7. Using a non-caustic degreasing agent, soak entire oil
cooler and let sit for several minutes.With low pressure
water, such as a garden hose with a spray nozzle,
thoroughly rinse oil cooler and air box out.
8. Re-install air box cover, air filter assembly and mount,
and tighten air intake hose connector.
Refer to your engine manual for additional information.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Replacing the Battery
REMOVABLE GUARDS AND ACCESS PANELS
For ease of service access, the guards and access panels
shown in Figure 47 are removable.
3
4
2
Figure 45. Battery Location
5
1. Remove rear access panel.
2. Disconnect both negative battery cables first, then
disconnect both positive battery cables to prevent arcing.
6
1
3. Remove top battery retainer clip (Figure 46, Item A).
4. Remove lower battery retainer (Figure 46, Item B).
1. Blade Guard
2. Rear Access Panel
3. Console Access Panel
4. Belt Guard
5. Carefully slide battery out of tray. Dispose of properly in
accordance with ordinances and regulations in your area.
6. Install new battery in tray.
5. Flange Guard
7. Install lower battery retainer. Push retainer tightly against
battery and tighten bolt.
6. Engine/SLH Guard
Figure 47. Guards & Panels
8. Install top battery retainer clip.
9. Re-connect both positive cables first, then both negative
cables to prevent arcing.
WARNING — Replace Guards
Replace guards and panels prior to starting the engine.
A
B
Figure 46. Battery Tray and Retainer Clips
PAGE44 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Engine must be at idle when engaging or disengaging blade
shaft drive:
BELTS AND PULLEYS
This saw uses a pair of Blade Shaft Drive Belts (5G 3VX
530) and a Hydrostatic Pump Belt (AX-35).
To STOP Blade shaft Rotation:
2
Push rocker switch labeled BLADE SHAFT forward. Engine
will tilt forward, disengaging the drive belt.
1
To START Blade shaft Rotation:
Push rocker switch lableled BLADE SHAFT backward.
Engine will tilt back, engaging the belt drive.
1
2
3
3
1. Blade Shaft Drive Belt
2. Pump Drive Belt
3. BeltTensioner Pulley
Figure 48. Belt Locations
V-Belt Tension
5
CAUTION — Keep belts clean
4
Keep belts clean of foreign material that may cause
slippage. Never dress belts as this can cause premature
failure.
1. Engine Sheave
2. Tensioner Nut
3. Tensioner Base
4. Jackshaft Pulley
5. Tensioner Pulley
The V-belt tension on this saw is automatically controlled
by the hydraulic system that actuates the blade shaft
engage/disengage system. Hydraulic pressure exerted on
the engine tilt cylinder applies force on the belt drive system
to engage blade shaft rotation.
Figure 49. Belt Drive System
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ROTARY BELTTENSIONER
BLADE SHAFT
The rotary belt tensioner system uses a 9/16"-headed nut
and a 15/16" or 1" nut to set belt tension by positioning an
arm between the tensioner pulley and the tensioner base.
Ridges on the base mark the amount of tension.
The fully enclosed blade shaft eliminates most maintenance
(Figures 51 and 52). Should the blade shaft need service
or repair however, contact the manufacturer for details.
Blade Shaft Assembly
Adjust to 3-1/2 notches on the tensioner:
1. Loosen the 9/16" nut.
2. Rotate the tensioner nut clockwise until the desired
belt tension is achieved.
3. Tighten the 9/16"nut.
3
Figure 51. Blade Shaft Assembly
External Components
2
4
5
1
6
1
7
2
3
1. 9/16" Nut
2. Tensioner Nut
3. Adjustment Notches
Figure 50.Tension Adjustment Notches
5
3
7
2
6
1. Bolt, 5/8 GR8
2. Bushing
1
4
3. Outer Flange
4. Inner Flange
5. Drive Key
6. Blade shaft
7. Blade shaft Housing
Figure 52. Blade Shaft External Components
PAGE46 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Removal and Replacement
DRIVE SYSTEM ALIGNMENT
To ensure correct blade shaft/wheel alignment, this
operation should be performed by an authorized service
center.
In addition to blade alignment, maintaining proper blade
and drive system alignment will allow the saw to cut lines
that are straight without much effort. Therefore the front
wheels and blade shaft axles MUST be at right angles to
the frame edge.
Blade Alignment
Maintaining proper blade and drive system alignment will
allow the saw to cut lines that are straight without much
effort. Therefore the blade shaft flanges MUST be
equadistant to the sides of the saw, (+/- .030"). See Figure
53 below where distance A must equal distance B.
In Figure 54, you see the distance “A” on the right side is
shown as “A + .187"” which means that the distance
between centers of the front and rear drive axles are 3/16"
longer than on the opposite side. This will have the effect
of causing the saw to “steer” slightly to the left. After
becoming familar with the saws particular sawing
characteristics, the operator may wish to have this alignment
altered to fit his own preferences or to fit a particular
application.
The second requirement for the blade is that it MUST be square
to horizontal (90o to flat surface). See Figure 53.
A + .187”
X
A
B
A
X
Figure 54. Wheel Alignment Requirements
Drive System Alignment Adjustment
90o
The drive wheels are aligned by adjusting the entire rear
drive assembly.
1. Loosen the transaxle attachment bolts just enough to
move the transaxle. Do not completely loosen the bolts.
Figure 53. Blade Alignment Requirements
2. Loosen and tighten the alignment jackscrew nuts to
move the transaxle, and thus the wheels, in the
appropriate direction to achieve the desired alignment
distance (Figure 54).
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3. Lock down the transaxle attachment bolts when the
appropriate alignment distance is set.
1
2
1. Blade Flange
2. Horseshoe Puller Plate
3. Puller Plate
4. Perimeter Bolt
5. Center Puller Bolt
6. Blade Mounting Bolt
Figure 56. Blade Flange Puller
Removing the Inner Blade Flange
1. With the outer blade flange in place, remove the blade
mounting bolt (Figure 56, item 6).
3
WARNING — Outer Flange
The outer flange MUST be in place to prevent the puller
assembly and inner flange from flying off when the taper
breaks loose. Injury or equipment damage could
otherwise result.
1. PivotAttachmentBolt
2. AdjustmentAttachmentBolts
3. AdjustmentScrew
Figure 55. Drive Wheel Alignment Bolt Locations
2. While the 3 perimeter bolts (item 4) hold the two puller
plates together, slide the horseshoe plate (item 2) of
the flange puller behind the shaft side of the inner
flange.
BLADE FLANGE REMOVAL/INSTALLATION
Correct removal or installation of the inner blade flange requires
a flange puller (p/n 18503). See Figure 56, items 2 and 3.
3. Tighten the center puller bolt (item 5) to remove the
inner flange from the blade shaft.
WARNING
If unfamilar with this operation, seek assistance or
training from someone that is familar with this operation.
Because of the tapered fit between the blade flange
and blade shaft, 5-10 tons of force is required to release
the inner flange from the blade shaft. Both parts and
tools can become dangerous projectiles if instructions
are not followed properly.
If the inner flange does not readily break free
from the tapered blade shaft while the center
puller bolt is tightened, lightly tap on the center
puller bolt to allow the flange to break free from
the shaft.
PAGE48 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
6. Loosen the mounting bolt and remove the outer flange
and bushing.
Installing the Inner Blade Flange
1. Ensure that the tapered portion of the blade shaft and the
inner blade flange are clean and free of burrs or
indentations. Clean and repair as necessary. See Figure
57.
7. Inspect the inner flange to ensure the proper seating
of the tapered fit. The inner flange should be seated
between .030" and 0.0" (flush) to the end of the blade
shaft. See Figure 58.
2. Ensure that the drive key (Figure 57, item 6) is in place.
3. Slide the Inner Flange (item 5) onto the tapered portion
of the blade shaft.
1
2
CAUTION — Do not use lubricant
0.000”
DO NOT use lubricant of any kind. Lubricant prevents
the tapered surface of the Flange and Shaft from mating
properly.
to 0.030”
3
4
4. Install the outer blade flange (item 3), flange bushing
(item 2), and mounting bolt (item 1).
1. Blade Shaft
5. Tighten with a 1/2" impact wrench to seat the tapered
surfaces of the inner flange and blade shaft.
2. Tolerance
3. Inner Flange Inside Face
4. Surface Area to be Checked
5
6
For Runout While Rotating
1
7
Figure 58. Inner Flange Seating
2
3
8. Test to ensure that the inner flange does not wobble
when rotated. Use a dial indicator on the face of the
flange (Figure 58, item 4). Maximum tolerance is .002"
runout on the face of the flange when rotated.
4
1. Mounting Bolt
2. Flange Bushing
3. Outer Flange
4. Dowel Pin
5. Inner Flange
6. Drive Key
7. Blade Shaft
Figure 57. Inner Blade Flange Installation
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CIRCUIT BREAKERS AND STARTER RELAYS
Thermal circuit breakers and glow plug starter relays are located
behind the console access cover at the top of the console.
See Figure 59.
2
1
2
1
3
4
3
1. Circuit Breakers
2. Relay, Glow Plug
3. DelayTimer
4. Starter Relay
Figure 59. Circuit Breakers and Starter Relay
4
1. Left-Side Stop Bolt
Under normal circumstances the circuit breakers do not require
service.They automatically reset when an overload condition
is corrected. If a breaker is cycling on and off, locate the cause
of the electrical overload and repair as required.
2. Right-Side Stop Bolt
3. Blade Flanges
4. Blade Shaft Housing
Figure 60. Depth Adjustment
MAXIMUM CUT DEPTH ADJUSTMENT
The saw comes factory-adjusted for maximum usable cut
depth. Should this setting need to be changed, perform the
following:
in several turns until it no longer makes contact with the
axle.
5. Adjust the left-side stop bolt (item 1) in or out until the
blade flange or lower belt guard achieves 1/8" to 3/16"
ground clearance.Tighten lock nut on left side.
While adjustment of the depth stop limiting
bolts can change the maximum usable cut
depth, they should not be adjusted to
compensate for unit “wobble” or blade/cut
problems.These are a result of other issues
that should be addressed.
6. Raise saw and place 2 jack stands under the blade shaft
housing.
7. Whileholdingtheraise-lowerswitchintheloweringposition,
raise the front axle assembly until it contacts the left-side
depth limiting stop bolt.
1. With the BLADE REMOVED, park the saw on a flat and
level surface.
8. While holding the axle firmly against the left-side depth
limiting stop bolt, screw the right-side depth limiting stop
bolt out until it makes contact with the axle. Tighten lock
nut on right side.
2. Fully lower the saw onto the depth limiting stop bolts. See
Figure 60.
3. Measure the distance from the blade flanges to the surface.
Following this procedure will prevent torsional stresses
being applied to the frame when fully lowered due to uneven
adjustment of depth limiting stop bolts.
4. If adjustment is required, loosen locknut on the right-side
depth limiting stop bolt (Figure 60, item 2) and screw bolt
PAGE50 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PTO DRIVE MAINTENANCE
RAISE-LOWER SYSTEM
Disassembly of the PTO drive and replacement of the PTO
drive sheave/bearing assembly requires the PTO bearing
puller, p/n 18610. The sheave/bearing assembly is not
serviceable and must be replaced as a complete unit.
Reference Figure 61 for components.
The saw uses a 12-volt hydraulic pump and hydraulic
cylinder to power the raise-lower system.
1. Check hydraulic oil level daily.
2. When checking or adding hydraulic oil, place the
machine so the saw frame is level to get an accurate
reading.
1
6
2
4
9
2
7
5
Figure 62. Hydraulic Oil Reservoir
3. Hydraulic oil should be 1/2" to 1" in the oil reserve
when cold.
1. Engine Adapter Plate
2. Belt Shoe
4. If hydraulic oil level is low, add oil to 1/2" to 1".
3. Drivebelt Pulley
4. Drivebelts
5. Use 15W-40 premium grade engine oil.
5. Blade shaft Pulley
6. Idler ArmTensioner
7. Idler Pulley
8
Idler Arm Belt
9. Pump Drive Pulley
Figure 61. PTO Drive Assembly
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
4
2
7
5
1
3
6
1. Pump Motor
2. Lift Pump Reservoir
3. Raise-LowerValve (Solenoid)
4. Raise-Lower Toggle
5. Raise-Lower Wire Harness
6. Lift Cylinder
7. Lift Pump Solenoid
Figure 63. Raise-Lower System
Raise-Lower System Troubleshooting
Refer to Figure 63 and the following table to assist in
troubleshooting the raise-lower system.
Table 11. Raise-Lower System Troubleshooting
Indication
Possible Causes
Battery discharged, raise-lower solenoid faulty, cables
loose or damaged, defective wiring
Won’t raise
Bad switch, faulty wiring connection, coil bad, valve
cartridge bad
Won’t lower
PAGE52 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
F-N-R CONTROL ADJUSTMENT
HYDRAULIC SYSTEM MAINTENANCE
DANGER — Hydraulic Leaks
NEVER use your hand to find hydraulic
leaks. Use a piece of wood or cardboard.
Hydraulic fluid injected into the skin must
be treated by a knowledgable physician
immediately or severe injury or death can
occur.
Many hydraulic problems are a result of low fluid levels.
Before checking any other possibilities, make sure the
hydraulic fluid level is correct. See Figure 66 for hydraulic
components. Hydraulic problems could be a result of the
following:
2
1
1. Incorrect hydraulic fluid level.
2. Plugged hydraulic oil filter
3. Loose or leaking fittings.
4. Ruptured/damaged hydraulic lines.
5. Faulty hydraulic pump.
3
4
2
1
3
1. Adjustment Nut
2. Rod End
Hydraulic Oil System
1. Check hydraulic oil level daily.
3. Push-Pull Cable
4. Neutral Safety Switch
2. When checking or adding hydraulic oil, place the
machine so the saw frame is level to get an accurate
reading.
Figure 64. F-N-R Control Adjustment
Control (cable) adjustment for the F-N-R should not normally
be necessary; however, some adjustment can be made on
each of the rod end adjustment nuts. See Figure 64.
3. Hydraulic oil should be 1/2" to 1" in the Oil Reserve
when cold.
4. If hydraulic oil level is low add oil to 1/2" to 1".
5. Use 15W-40 premium grade engine oil.
Figure 65. Oil Reserve Fill Line
6. Change oil and filter annually. See Figure 65.
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1
2
3
1. Hydraulic Reservoir
2. Filter
3. Pump
7
4. Wheel Motor
5. Engine Pivot Cylinder
6. EngineTilt Cylinder
7. Motor
5
8
8. Pump Body
9. Lift Cylinder
4
6
9
4
Figure 66. Hydraulic System
DRAININGTHE HYDRAULIC SYSTEM
CAUTION — Pre-fill Filter
To prevent hydraulic pump damage, pre-fill the filter with
oil prior to installing it.
7. Add oil to the system reservoir.
1
2
8. The reservoir will need to be filled several times.
3
9. Run the engine for 5-10 minutes to cycle the oil
throughout the system.
Figure 67. Hydraulic System Drains
10. Add oil as required.
1. Place an oil pan beneath the Blade Shaft Housing
(Figure 67, item 1).
11. Repeat process until oil level is stable after running
engine.
2. Remove the drain plug from the bottom of the blade
shaft housing (item 3)
3. Collect and dispose of the used oil (and filter) in
accordance with ordinances and regulations of your
area.
4. Remove used oil filter.
5. After oil is drained, reinstall drain plug.
6. Pre-fill and install a new oil filter.
PAGE54 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Tips When Draining and Filling the Hydraulic Oil
System
LONGTERM STORAGE
■
■
■
■
Remove the battery.
1. It will take 3-4 quarts to fill the hydraulic system when
new and somewhat less when changing the oil.
Drain fuel from fuel tank and fuel lines.
Clean exterior with a cloth soaked in clean oil.
2. Remove the oil reservoir cap to speed oil draining.
Store unit covered with plastic sheet in moisture and
dust-free location out of direct sunlight.
3. When refilling the system, raise the saw halfway up,
then lift the rear of the saw until the blade flanges touch
the ground. This will help to speed the filling process.
CAUTION — Fuel
4. After filling the system, jack the saw up so the drive
wheels are off the ground. Start the saw and move the
control handle half way into FORWARD to purge air
out of the system.
Never store the saw with fuel in the tank for any extended
period of time.Always clean up spilled fuel immediately.
DECOMMISSIONING SAW/COMPONENTS
Decommissioning is a controlled process used to safely
retire a piece of equipment that is no longer serviceable. If
the equipment poses an unacceptable and unrepairable
safety risk due to wear or damage or is no longer cost
effective to maintain (beyond life-cycle reliability) and is to
be decommissioned (demolition and dismantlement), the
following procedure must take place:
If the blade shaft is drained completely, it will
require approximately 1 gallon to refill.
Stay-Level Handles (SLH)
1. Drain all fluids completely. These may include oil,
gasoline, hydraulic oil and antifreeze. Dispose of
properly in accordance with local and governmental
regulations. Never pour on ground or dump down drains
or sewers.
The stay-level handlebar system is designed to require very
little maintenance (Figure 68).
NEVER try to lift the saw with the handlebars (a lift bale is
provided for lifting). DO NOT try to dislodge a stuck blade
by prying or using excessive force on the handlebars.
2. Remove battery and bring to appropriate facility for lead
reclamation. Use safety precautions when handling
batteries that contain sulfuric acid.
3. The remainder can be brought to a salvage yard or
metal reclamation facility for further dismantling.
Figure 68. Stay Level Handlebar System
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
TABLE 12. TROUBLESHOOTING (ENGINE)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Emergency stop button pushed in?
Pull out E-Stop button.
Check cable connections, charge
or replace battery.
Battery disconnected or discharged?
Ignition switch/wiring defective?
Will not start, no power with key “ON.”
Replace ignition switch. Check
wiring.
Fuel not available in fuel tank (tank
empy)?
Fill with correct type of fuel.
Fuel filter/lines clogged?
Replace fuel filter or fuel lines.
Clean or replace fuel tank cap.
Bleed fuel line.
Will not start. No fuel present.
Fuel tank cap breather hole clogged?
Air in fuel line?
Injection valve clogged or defective?
Clean or replace.
Flush fuel system, and replace
with correct type of fuel.
Wrong fuel type?
Difficult to start, “fuel is available and
compression is normal.”
Contaminated fuel system (water, dirt)?
Air cleaner dirty?
Flush fuel system.
Replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and/or
piston.
Piston ring and/or cylinder worn?
Difficult to start, ”fuel is available and
compression is low.”
Cylinder head not tightened properly?
Head gasket damaged?
Torque cylinder head bolts
Replace head gaskets.
Certain operations referred to in this
troubleshooting section such as re-seating
valves or replacing piston rings may require
specialtoolsandmustbeperformedbytrained
andcompetentpersonnel.
For further engine troubleshooting, see your
engine owner's manual
PAGE56 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (ENGINE)
TABLE 12. TROUBLESHOOTING (ENGINE, CONTINUED)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Clear air intake of dirt and debris.
Replace air cleaner elements as
necessary.
Intake air restricted?
Flush fuel system if contaminated.
Refill with clean fuel of prescribed
quality.
“Weak in power” compression is proper
and does not misfire.
Improper fuel or contaminated fuel?
Injection line leaks?
Repair or replace lines.
Repair or replace line.
Charge air line leaking?
Flush fuel system and replace with
correct type fuel.
Water in fuel system?
“Weak in power” compression is proper
but misfires.
Ignition defective?
Replace ignition.
Damaged or worn injector orifices?
Clean or replace injectors.
Flush fuel system, and replace with
correct type of fuel.
Wrong fuel type?
Clear air intake of dirt and debris.
Replace air cleaner elements as
necessary.
Intake air restricted?
Engine overheats.
Injection valve defective?
Replace injection valve.
Clean cooling fins.
Cooling fins dirty?
Oil level too low or too high?
Governor adjusted correctly?
Governor spring defective or missing?
Adjust oil to proper level.
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Starter malfunction.
Check entire fuel system for leaks or
clogs.
Fuel flow restricted?
Ensure tight, clean connections on
battery and starter.
Loose, damaged wiring?
Battery insufficiently charged?
Recharge or replace battery.
Replace starter.
Starter damaged or internally shorted?
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (BLADE)
TABLE 13. BLADE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
Consult dealer or Multiquip for correct blade. Try cutting
very soft material (sandstone, silica brick, cinder block) to
“redress” the blade.
Blade too hard for the material being
cut?
Engine torque diminished because of
loose or worn drive-belts?
Re-tension belts or replace.
Blade slows or stops cutting.
Insufficient engine power?
Check throttle setting. Refer to Engine Troubleshooting.
Check that the blade is properly oriented and rotational
arrow points in a “down-cutting” direction.
Improper direction of rotation?
Check that the blade and flange pin are properly installed
on the blade shaft.
Blade is slipping on the blade shaft?
Blade misaligned on saw?
Check alignment integrity.
Check blade shaft and flange for wear, damage and blade
seating.
“Cut gap” excessive or blade wobble?
Blade is excessively hard for the
material being cut?
Check specification of the blade with the material being
cut. Consult dealer or Multiquip for information.
Blade does not cut straight
and/or true.
Ensure blade surface feet per minute speed (SFPM) is
approximately 10,000.
Blade being used at improper RPM?
Blade improperly mounted on arbor
shoulders and flanges?
Ensure blade is properly affixed on the blade shaft.
Excessive force applied to blade while
cutting?
DO NOT force the blade in the cut. Apply a slow and
steady pace when sawing.
Blade wearing out on one side and
not the other?
Check blade shaft and flange for wear, damage and blade
seating.
Consult Dealer or Multiquip for correct blade. Try cutting
very soft material (sandstone, silica brick, cinder block) to
“redress” the blade.
Blades too hard for the material being
cut?
Blade improperly mounted on arbor
shoulders and flanges?
Ensure blade is properly affixed on the blade shaft.
Blade discoloring, crackling
and/or wearing excessively.
Blade not receiving enough cooling
water?
Ensure proper flow and volume of water is provided for
wet cutting blades.
Arbor hole out of round?
Ensure blade is properly affixed on the blade shaft.
Incorrect blade chosen for material
being cut?
Check specification of the blade with the material being
cut. Consult dealer or Multiquip for information.
Diamond abrasive material worn away or burnished into
the metal. Check saw for alignment or damage and
replace saw blade.
Excessive force applied to blade while
cutting?
PAGE58 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL DIAGRAM TO SN AF3700155
ELECTRICAL DIAGRAM UP TO S/N AF3700155
III
III
III
III
II
II
II
I
0
I
12 AWG Red
12 AWG Red
16 AWG Red/Black
PAGE60 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL DIAGRAM SN AF3700156 & UP
ELECTRICAL DIAGRAM S/N AF3700156 AND UP
.
e R d / B l a c A k W G 1 6
.
.
.
.
3 1
I N 1
I N 2
3 0
O u t
B l a c k A W G 1 6
i n P k / B l a c A k W G 1 4
d e R e A W G 1 6
.
.
.
.
.
.
d e R e A W G 1 2
d e R e A W G 1 2
I
0
I I
I
I I
I I I
I I
I I I
I I I
I I I
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SCHEMATIC TO SN AF3700155
HYDRAULIC SCHEMATICTO SN AF3700155
1. Lift Cylinder Assembly
2. Lift Pump
10. Wheel Motor
11. Velocity Fuse
12. CheckValve (2)
13. Valve 4W2P
14. Lift Cylinder
15. Pilot Piston
16. O-Ring
3. Reservoir
4. Blade Shaft Assembly
5. Brake Cylinder
6. Spin-On Filter
7. Hydrostatic Pump
8. Engine Pivot Cylinder 2.5"
9. Valve Assembly
17. Backup (2)
PAGE62 — SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SCHEMATIC SN AF3700156 & UP
HYDRAULIC SCHEMATIC SN AF3700156 AND UP
1. Lift Cylinder Assembly
2. Lift Pump
10. CheckValve (2)
11. Velocity Fuse
12. Engine Pivot Cylinder 2.5"
13. Valve 4W2P
3. Reservoir
4. Blade Shaft Assembly
5. Brake Cylinder
14. Lift Cylinder
15. Pilot Piston
6. Spin-On Filter
7. Hydrostatic Pump
8. Cylinder andValve Assembly
9. Wheel Motor
16. O-Ring
17. Backup (2)
SP7060 PAVEMENT SAW • OPERATION MANUAL — REV. #0 (02/13/09) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION MANUAL
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Mayco Parts
Warranty Department
800-306-2926
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
800-421-1244, Ext. 279
310-537-3700, Ext. 279
Fax: 310-537-1173
Fax: 310-631-5032
Service Department
Technical Assistance
800-421-1244
310-537-3700
Fax: 310-537-4259
800-478-1244
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Tel: 0161 339 2223
Fax: 0161 339 3226
Contact: sales@multiquip.co.uk
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2009, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|
MTD Log Splitter 24632C User Manual
NEC Flat Panel Television P701AVT User Manual
NordicTrack Treadmill 83129881 User Manual
Nortel Networks Answering Machine CalPilot 40 User Manual
Nortel Networks Telephone P0609347 02 User Manual
Numark Industries CD Player CDN22 User Manual
Oster Mixer 111805 003 User Manual
Panasonic Cell Phone EB GD92 User Manual
Panasonic Patio Furniture EP MA10 User Manual
Parker Hannifin Video Game Console P N88023735 01A User Manual